hw/char/escc: Lower irq when transmit buffer is filled
PATCH 1/1 hw/char/escc: Lower irq when transmit buffer is filled
The SCC/ESCC will briefly stop asserting an interrupt when the transmit FIFO is filled.
This code doesn't model the transmit FIFO/shift register so the pending transmit interrupt is never deasserted which means that an edge-triggered interrupt controller will never see the low-to-high transition it needs to raise another interrupt. The practical consequence of this is that guest firmware with an interrupt service routine for the ESCC that does not send all of the data it has immediately will stop sending data if the following sequence of events occurs:
1. Disable processor interrupts
2. Write a character to the ESCC
3. Add additional characters to a buffer which is drained by the ISR
4. Enable processor interrupts
In this case, the first character will be sent, the interrupt will fire and the ISR will output the second character. Since the pending transmit interrupt remains asserted, no additional interrupts will ever fire.
This fixes that situation by explicitly lowering the IRQ when a character is written to the buffer.
--- hw/char/escc.c | 1 + 1 file changed, 1 insertion(+)
hw/char/escc.c +1 -0
@@ -509,6 +509,7 @@ static void escc_mem_write(void *opaque, hwaddr addr,break ;case SERIAL_DATA :trace_escc_mem_writeb_data (CHN_C (s), val); +qemu_irq_lower (s->irq); s->tx = val;if (s->wregs[W_TXCTRL2 ] &TXCTRL2_TXEN ) {// tx enabled if (qemu_chr_fe_backend_connected (&s->chr)) {
Signature · 1 line
2.17.2 (Apple Git-113)
Quoted 21 lines · Stephen Checkoway
The SCC/ESCC will briefly stop asserting an interrupt when the transmit FIFO is filled.
This code doesn't model the transmit FIFO/shift register so the pending transmit interrupt is never deasserted which means that an edge-triggered interrupt controller will never see the low-to-high transition it needs to raise another interrupt. The practical consequence of this is that guest firmware with an interrupt service routine for the ESCC that does not send all of the data it has immediately will stop sending data if the following sequence of events occurs:
1. Disable processor interrupts
2. Write a character to the ESCC
3. Add additional characters to a buffer which is drained by the ISR
4. Enable processor interruptsIn this case, the first character will be sent, the interrupt will fire and the ISR will output the second character. Since the pending transmit interrupt remains asserted, no additional interrupts will ever fire.
Quoted 4 lines
This fixes that situation by explicitly lowering the IRQ when a character is written to the buffer.
Signed-off-by Stephen Checkoway <[email protected]>
Looks good but I would like Mark to give his ack as well.
Mark, could you also add hw/char/escc.c to both SPARC and Mac sections of MAINTAINERS?
Thanks,
Paolo
Quoted 17 lines
--- hw/char/escc.c | 1 + 1 file changed, 1 insertion(+)hw/char/escc.c +1
-0@@ -509,6 +509,7 @@ static void escc_mem_write(void *opaque, hwaddr addr,break ;case SERIAL_DATA :trace_escc_mem_writeb_data (CHN_C (s), val); +qemu_irq_lower (s->irq); s->tx = val;if (s->wregs[W_TXCTRL2 ] &TXCTRL2_TXEN ) {// tx enabled if (qemu_chr_fe_backend_connected (&s->chr)) {
Quoted 25 lines · Paolo Bonzini
Quoted 24 lines · Stephen Checkoway
The SCC/ESCC will briefly stop asserting an interrupt when the transmit FIFO is filled.
This code doesn't model the transmit FIFO/shift register so the pending transmit interrupt is never deasserted which means that an edge-triggered interrupt controller will never see the low-to-high transition it needs to raise another interrupt. The practical consequence of this is that guest firmware with an interrupt service routine for the ESCC that does not send all of the data it has immediately will stop sending data if the following sequence of events occurs:
1. Disable processor interrupts
2. Write a character to the ESCC
3. Add additional characters to a buffer which is drained by the ISR
4. Enable processor interruptsIn this case, the first character will be sent, the interrupt will fire and the ISR will output the second character. Since the pending transmit interrupt remains asserted, no additional interrupts will ever fire.
This fixes that situation by explicitly lowering the IRQ when a character is written to the buffer.
Quoted 6 lines
Quoted 1 line
Signed-off-by Stephen Checkoway <[email protected]>Looks good but I would like Mark to give his ack as well.
Mark, could you also add
hw/char/escc.cto both SPARC and Mac sections ofMAINTAINERS?
Cc'ing Artyom who also made some changes in this file, and Laurent.
Stephen, which particular chipset are you using?
This file models various types. I had a talk with Mark or Laurent at last KVM forum about this device. IIRC, while the sun4m machines use a real chipset, the MacIO embeds an slighly modified IP core.
I can't find what you describe in the Z85C30 doc, however in the ESCC datasheet referenced in escc.c (which happens to be a 85MiB pdf!!!) I found:
Transmit Interrupts and Transmit Buffer Empty Bit on the NMOS/CMOS
The TxIP is reset either by writing data to the transmit buffer or by issuing the Reset Tx Int command in WR0.
I understand the NMOS/CMOS desc. matches the Z85C30 (no FIFO used).
So your description and patch makes sens.
What worries me is the controller could have other pending IRQs to deliver and you are clearing them. Shouldn't we only clear the INTR_TXINT bit, and call escc_update_irq() which should lower the IRQ if no bits are pending?
Maybe as:
s->wregs[W_INTR] &= ~INTR_TXINT;
escc_update_irq(s);Thanks,
Phil.
Quoted 23 lines
Thanks,
Paolo
Quoted 17 lines
--- hw/char/escc.c | 1 + 1 file changed, 1 insertion(+)hw/char/escc.c +1
-0@@ -509,6 +509,7 @@ static void escc_mem_write(void *opaque, hwaddr addr,break ;case SERIAL_DATA :trace_escc_mem_writeb_data (CHN_C (s), val); +qemu_irq_lower (s->irq); s->tx = val;if (s->wregs[W_TXCTRL2 ] &TXCTRL2_TXEN ) {// tx enabled if (qemu_chr_fe_backend_connected (&s->chr)) {
Quoted 30 lines · Philippe Mathieu-Daudé
Quoted 29 lines · Paolo Bonzini
Quoted 21 lines · Stephen Checkoway
The SCC/ESCC will briefly stop asserting an interrupt when the transmit FIFO is filled.
This code doesn't model the transmit FIFO/shift register so the pending transmit interrupt is never deasserted which means that an edge-triggered interrupt controller will never see the low-to-high transition it needs to raise another interrupt. The practical consequence of this is that guest firmware with an interrupt service routine for the ESCC that does not send all of the data it has immediately will stop sending data if the following sequence of events occurs:
1. Disable processor interrupts
2. Write a character to the ESCC
3. Add additional characters to a buffer which is drained by the ISR
4. Enable processor interruptsIn this case, the first character will be sent, the interrupt will fire and the ISR will output the second character. Since the pending transmit interrupt remains asserted, no additional interrupts will ever fire.
Quoted 4 lines
This fixes that situation by explicitly lowering the IRQ when a character is written to the buffer.
Signed-off-by Stephen Checkoway <[email protected]>Looks good but I would like Mark to give his ack as well.
Quoted 7 lines
Quoted 2 lines
Mark, could you also add
hw/char/escc.cto both SPARC and Mac sections ofMAINTAINERS?Cc'ing Artyom who also made some changes in this file, and Laurent.
Stephen, which particular chipset are you using?
I'm away from the hardware, but my notes say Z80C30. I've included the image from the board if you want to try to decipher the rest of the part number. My best guess is it's a Z85C3008VEC. If it's important, I can ask someone who is a few thousand km closer to the hardware than I currently am to take a look.
Quoted 6 lines
This file models various types. I had a talk with Mark or Laurent at last KVM forum about this device. IIRC, while the sun4m machines use a real chipset, the MacIO embeds an slighly modified IP core.
I can't find what you describe in the Z85C30 doc, however in the ESCC datasheet referenced in
escc.c(which happens to be a 85MiB pdf!!!) I found:
(This chip is ridiculously configurable, I honestly found it much easier to write a driver by reverse engineering existing firmware than by reading the part sheet.)
Quoted 7 lines
Transmit Interrupts and Transmit Buffer Empty Bit on the NMOS/CMOS
The TxIP is reset either by writing data to the transmit buffer or by issuing the Reset Tx Int command in WR0.
I understand the NMOS/CMOS desc. matches the Z85C30 (no FIFO used).
It has been a little while since I was last looking at this, but my recollection was the SCC has a 1-byte transmit buffer and the ESCC has a small (4 maybe?) byte transmit buffer. But in either case writing data to the transmit buffer should clear the interrupt.
Quoted 10 lines
So your description and patch makes sens.
What worries me is the controller could have other pending IRQs to deliver and you are clearing them. Shouldn't we only clear theINTR_TXINTbit, and callescc_update_irq()which should lower the IRQ if no bits are pending?Maybe as:
s->wregs[W_INTR] &= ~INTR_TXINT; escc_update_irq(s);
Ah, I think I see. In this case, escc_update_irq() will lower the IRQ if no other interrupts are pending and the set_txint() will raise it again. Otherwise, it'll remain raised. I can give this a shot and see how it goes. (I think this should be R_INTR instead of W_INTR, but I'll double check once I have an opportunity to dig into this again.)
Thanks for looking at this!
Steve
Signature · 1 line
Stephen Checkoway
Quoted 10 lines · Philippe Mathieu-Daudé
So your description and patch makes sens.
What worries me is the controller could have other pending IRQs to deliver and you are clearing them. Shouldn't we only clear theINTR_TXINTbit, and callescc_update_irq()which should lower the IRQ if no bits are pending?
Quoted 4 lines
Maybe as:
s->wregs[W_INTR] &= ~INTR_TXINT; escc_update_irq(s);
I just sent a v2 patch (but it looks like I failed to include Philippe, sorry about that!)
I used
s->txint = 0;
escc_update_irq(s);which appears to do the right thing in my tests.
Thank you,
Steve
Signature · 1 line
Stephen Checkoway