staging: octeon-usb octeon-hcd: Fix several typos.
PATCH 1/1 staging: octeon-usb octeon-hcd: Fix several typos.
I found that the comments had several typos such as "aenable", "internaly" and some others. I fixed them all.
Signed-off-by Laura Lazzati <[email protected]>
--- drivers/staging/octeon-usb/octeon-hcd.h | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-)
drivers/staging/octeon-usb/octeon-hcd.h +5 -5
@@ -1711,7 +1711,7 @@ union cvmx_usbnx_usbp_ctl_status {* Indicates an internal error was detected during * the BIST sequence. * @tdata_out: PHY Test Data Out. -* Presents either internaly generated signals or +* Presents either internally generated signals or * test register contents, based upon the value of * test_data_out_sel. * @siddq: Drives the USBP (USB-PHY) SIDDQ input.
@@ -1737,7 +1737,7 @@ union cvmx_usbnx_usbp_ctl_status {* to D+. When an A/B device is acting as a host * (downstream-facing port), dp_pulldown and * dm_pulldown are enabled. This must not toggle -* during normal opeartion. +* during normal operation. * @dm_pulld: PHY DM_PULLDOWN input to the USB-PHY. * This signal enables the pull-down resistance on * the D- line. '1' pull down-resistance is connected
@@ -1745,7 +1745,7 @@ union cvmx_usbnx_usbp_ctl_status {* to D-. When an A/B device is acting as a host * (downstream-facing port), dp_pulldown and * dm_pulldown are enabled. This must not toggle -* during normal opeartion. +* during normal operation. * @hst_mode: When '0' the USB is acting as HOST, when '1' * USB is acting as device. This field needs to be * set while the USB is in reset.
@@ -1784,7 +1784,7 @@ union cvmx_usbnx_usbp_ctl_status {* Used to activate BIST in the PHY. * @tdata_sel: Test Data Out Select. * '1' test_data_out[3:0] (PHY) register contents -* are output. '0' internaly generated signals are +* are output. '0' internally generated signals are * output. * @taddr_in: Mode Address for Test Interface. * Specifies the register address for writing to or
@@ -1797,7 +1797,7 @@ union cvmx_usbnx_usbp_ctl_status {* This is a test signal. When the USB Core is * powered up (not in Susned Mode), an automatic * tester can use this to disable phy_clock and -* free_clk, then re-eanable them with an aligned +* free_clk, then re-enable them with an aligned * phase. * '1': The phy_clk and free_clk outputs are * disabled. "0": The phy_clock and free_clk outputs
Signature · 1 line
2.17.1
Hi,
Quoted 4 lines · Laura Lazzati
I found that the comments had several typos such as "aenable", "internaly" and some others. I fixed them all.
Signed-off-by Laura Lazzati <[email protected]>
I spotted one more typo that could be fixed as well:
drivers/staging/octeon-usb/octeon-hcd.h union cvmx_usbnx_usbp_ctl_status { · line 1798
Quoted 3 lines
drivers/staging/octeon-usb/octeon-hcd.h +0
-0@@ -1797,7 +1797,7 @@ union cvmx_usbnx_usbp_ctl_status {* This is a test signal. When the USB Core is * powered up (not in Susned Mode), an automatic
^^^^^^
Should be "Suspend".
A.