drm/bridge/synopsys: dsi: Wait for all active lanes to reach stop
Subsystems (3)
PATCH 1/1 drm/bridge/synopsys: dsi: Wait for all active lanes to reach stop
The Synopsys manual states that software should wait for all active lanes to reach stop state (User manual section 3.1.5). Currently the driver only waits for / checks that the clock lane is in stop state. Fix this by waiting for the mask of PHY STATUS bits corresponding to the active lanes to be set.
---
drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c | 15 ++++++++++++--- 1 file changed, 12 insertions(+), 3 deletions(-)
drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c +12 -3
@@ -189,6 +189,10 @@#define DSI_PHY_TX_TRIGGERS 0xac#define DSI_PHY_STATUS 0xb0 +#define PHY_STOP_STATE_LANE_3 BIT(11) +#define PHY_STOP_STATE_LANE_2 BIT(9) +#define PHY_STOP_STATE_LANE_1 BIT(7) +#define PHY_STOP_STATE_LANE_0 BIT(4)#define PHY_STOP_STATE_CLK_LANE BIT(2)#define PHY_LOCK BIT(0)
@@ -752,7 +756,7 @@ static void dw_mipi_dsi_dphy_init(struct dw_mipi_dsi *dsi)static void dw_mipi_dsi_dphy_enable (struct dw_mipi_dsi *dsi) { -u32 val; +u32 val, mask;int ret; dsi_write(dsi, DSI_PHY_RSTZ, PHY_ENFORCEPLL | PHY_ENABLECLK |
@@ -763,11 +767,16 @@ static void dw_mipi_dsi_dphy_enable(struct dw_mipi_dsi *dsi)if (ret)DRM_DEBUG_DRIVER ("failed to wait phy lock state\n" ); + mask =PHY_STOP_STATE_CLK_LANE |PHY_STOP_STATE_LANE_0 ; + mask |= (dsi->lanes >=2 ) ?PHY_STOP_STATE_LANE_1 :0 ; + mask |= (dsi->lanes >=3 ) ?PHY_STOP_STATE_LANE_2 :0 ; + mask |= (dsi->lanes ==4 ) ?PHY_STOP_STATE_LANE_3 :0 ; + ret =readl_poll_timeout (dsi->base +DSI_PHY_STATUS , - val, val &PHY_STOP_STATE_CLK_LANE ,1000 , + val, (val & mask) == mask,1000 ,PHY_STATUS_TIMEOUT_US );if (ret) -DRM_DEBUG_DRIVER ("failed to wait phy clk lane stop state\n" ); +DRM_DEBUG_DRIVER ("failed to wait phy stop state\n" ); }static void dw_mipi_dsi_clear_err (struct dw_mipi_dsi *dsi)
Signature · 1 line
2.17.1
Hi Matt,
Thank you for the patch.
Quoted 7 lines · Matt Redfearn
The Synopsys manual states that software should wait for all active lanes to reach stop state (User manual section 3.1.5). Currently the driver only waits for / checks that the clock lane is in stop state. Fix this by waiting for the mask of PHY STATUS bits corresponding to the active lanes to be set.
Signed-off-by Matt Redfearn <[email protected]>
I don't have access to the datasheet, but the change makes sense.
Quoted 48 lines
---
drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c | 15 ++++++++++++--- 1 file changed, 12 insertions(+), 3 deletions(-)drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c +12
-3@@ -189,6 +189,10 @@#define DSI_PHY_TX_TRIGGERS 0xac#define DSI_PHY_STATUS 0xb0 +#define PHY_STOP_STATE_LANE_3 BIT(11) +#define PHY_STOP_STATE_LANE_2 BIT(9) +#define PHY_STOP_STATE_LANE_1 BIT(7) +#define PHY_STOP_STATE_LANE_0 BIT(4)#define PHY_STOP_STATE_CLK_LANE BIT(2)#define PHY_LOCK BIT(0)@@ -752,7 +756,7 @@ static void dw_mipi_dsi_dphy_init(struct dw_mipi_dsi *dsi)static void dw_mipi_dsi_dphy_enable (struct dw_mipi_dsi *dsi) { -u32 val; +u32 val, mask;int ret; dsi_write(dsi, DSI_PHY_RSTZ, PHY_ENFORCEPLL | PHY_ENABLECLK |@@ -763,11 +767,16 @@ static void dw_mipi_dsi_dphy_enable(struct dw_mipi_dsi *dsi)if (ret)DRM_DEBUG_DRIVER ("failed to wait phy lock state\n" ); + mask =PHY_STOP_STATE_CLK_LANE |PHY_STOP_STATE_LANE_0 ; + mask |= (dsi->lanes >=2 ) ?PHY_STOP_STATE_LANE_1 :0 ; + mask |= (dsi->lanes >=3 ) ?PHY_STOP_STATE_LANE_2 :0 ; + mask |= (dsi->lanes ==4 ) ?PHY_STOP_STATE_LANE_3 :0 ; + ret =readl_poll_timeout (dsi->base +DSI_PHY_STATUS , - val, val &PHY_STOP_STATE_CLK_LANE ,1000 , + val, (val & mask) == mask,1000 ,PHY_STATUS_TIMEOUT_US );if (ret) -DRM_DEBUG_DRIVER ("failed to wait phy clk lane stop state\n" ); +DRM_DEBUG_DRIVER ("failed to wait phy stop state\n" ); }static void dw_mipi_dsi_clear_err (struct dw_mipi_dsi *dsi)
Signature · 7 lines
Regards, Laurent Pinchart _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel