Skip to contentSkip to conversation

rk3399: orangepi: Enable TPL

PATCH Superseded Jagan Teki 3 participants 10 messages May 9, 2019 – Jun 1, 2019 5 messages not in the archive Arm Rockchip

v1 of 2 Superseded Latest is v2 →

lore
Share & tools
lore

Jagan Teki

author
#0 lore raw

PATCH 1/3 rk3399: orangepi: Enable TPL

Enable TPL for OrangePI rk3399 board.

Signed-off-by Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
---
 configs/orangepi-rk3399_defconfig | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)
configs/orangepi-rk3399_defconfig +4 -3
index 3f02c89983..90021bb695 100644
@@ -5,7 +5,7 @@ CONFIG_SPL_LIBCOMMON_SUPPORT=y
 CONFIG_SPL_LIBGENERIC_SUPPORT=y
 CONFIG_SYS_MALLOC_F_LEN=0x4000
 CONFIG_ROCKCHIP_RK3399=y
-CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x4000
+CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x50000
 CONFIG_DEBUG_UART_BASE=0xFF1A0000
 CONFIG_DEBUG_UART_CLOCK=24000000
 CONFIG_SPL_STACK_R_ADDR=0x80000

@@ -14,9 +14,8 @@ CONFIG_NR_DRAM_BANKS=1
 CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-orangepi.dtb"
 # CONFIG_DISPLAY_CPUINFO is not set
 CONFIG_DISPLAY_BOARDINFO_LATE=y
-CONFIG_SPL_TEXT_BASE=0xff8c2000
 CONFIG_SPL_STACK_R=y
-CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x4000
+CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000
 CONFIG_CMD_BOOTZ=y
 CONFIG_CMD_GPT=y
 CONFIG_CMD_MMC=y

@@ -24,6 +23,7 @@ CONFIG_CMD_SF=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_TIME=y
+CONFIG_TPL=y
 CONFIG_SPL_OF_CONTROL=y
 CONFIG_DEFAULT_DEVICE_TREE="rk3399-orangepi"
 CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"

@@ -56,4 +56,5 @@ CONFIG_USB_ETHER_MCS7830=y
 CONFIG_USB_ETHER_RTL8152=y
 CONFIG_USB_ETHER_SMSC95XX=y
 CONFIG_USE_TINY_PRINTF=y
+CONFIG_SPL_TINY_MEMSET=y
 CONFIG_ERRNO_STR=y
Signature · 1 line
2.18.0.321.gffc6fa0e3

A message that is not in the archive (sent off-list or not yet received): 20190509105746.24830-1-jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org

author
#2 lore raw

PATCH 2/3 rk3399: nanopi4: Enable TPL

Enable TPL for NanoPC T4, NanoPI M4 boards.

Signed-off-by Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
---
 configs/nanopc-t4-rk3399_defconfig | 7 ++++---
 configs/nanopi-m4-rk3399_defconfig | 7 ++++---
 2 files changed, 8 insertions(+), 6 deletions(-)
configs/nanopc-t4-rk3399_defconfig +4 -3
index d9f2137b4c..9b7e15d63a 100644
@@ -5,7 +5,7 @@ CONFIG_SPL_LIBCOMMON_SUPPORT=y
 CONFIG_SPL_LIBGENERIC_SUPPORT=y
 CONFIG_SYS_MALLOC_F_LEN=0x4000
 CONFIG_ROCKCHIP_RK3399=y
-CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x4000
+CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x50000
 CONFIG_DEBUG_UART_BASE=0xFF1A0000
 CONFIG_DEBUG_UART_CLOCK=24000000
 CONFIG_SPL_STACK_R_ADDR=0x80000

@@ -14,9 +14,8 @@ CONFIG_NR_DRAM_BANKS=1
 CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-nanopc-t4.dtb"
 # CONFIG_DISPLAY_CPUINFO is not set
 CONFIG_DISPLAY_BOARDINFO_LATE=y
-CONFIG_SPL_TEXT_BASE=0xff8c2000
 CONFIG_SPL_STACK_R=y
-CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x4000
+CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000
 CONFIG_CMD_BOOTZ=y
 CONFIG_CMD_GPT=y
 CONFIG_CMD_MMC=y

@@ -24,6 +23,7 @@ CONFIG_CMD_SF=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_TIME=y
+CONFIG_TPL=y
 CONFIG_SPL_OF_CONTROL=y
 CONFIG_DEFAULT_DEVICE_TREE="rk3399-nanopc-t4"
 CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"

@@ -56,4 +56,5 @@ CONFIG_USB_ETHER_MCS7830=y
 CONFIG_USB_ETHER_RTL8152=y
 CONFIG_USB_ETHER_SMSC95XX=y
 CONFIG_USE_TINY_PRINTF=y
+CONFIG_SPL_TINY_MEMSET=y
 CONFIG_ERRNO_STR=y
configs/nanopi-m4-rk3399_defconfig +4 -3
index c2832788f0..92e70dd939 100644
@@ -5,7 +5,7 @@ CONFIG_SPL_LIBCOMMON_SUPPORT=y
 CONFIG_SPL_LIBGENERIC_SUPPORT=y
 CONFIG_SYS_MALLOC_F_LEN=0x4000
 CONFIG_ROCKCHIP_RK3399=y
-CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x4000
+CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x50000
 CONFIG_DEBUG_UART_BASE=0xFF1A0000
 CONFIG_DEBUG_UART_CLOCK=24000000
 CONFIG_SPL_STACK_R_ADDR=0x80000

@@ -14,9 +14,8 @@ CONFIG_NR_DRAM_BANKS=1
 CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-nanopi-m4.dtb"
 # CONFIG_DISPLAY_CPUINFO is not set
 CONFIG_DISPLAY_BOARDINFO_LATE=y
-CONFIG_SPL_TEXT_BASE=0xff8c2000
 CONFIG_SPL_STACK_R=y
-CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x4000
+CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000
 CONFIG_CMD_BOOTZ=y
 CONFIG_CMD_GPT=y
 CONFIG_CMD_MMC=y

@@ -24,6 +23,7 @@ CONFIG_CMD_SF=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_TIME=y
+CONFIG_TPL=y
 CONFIG_SPL_OF_CONTROL=y
 CONFIG_DEFAULT_DEVICE_TREE="rk3399-nanopi-m4"
 CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"

@@ -56,4 +56,5 @@ CONFIG_USB_ETHER_MCS7830=y
 CONFIG_USB_ETHER_RTL8152=y
 CONFIG_USB_ETHER_SMSC95XX=y
 CONFIG_USE_TINY_PRINTF=y
+CONFIG_SPL_TINY_MEMSET=y
 CONFIG_ERRNO_STR=y
Signature · 1 line
2.18.0.321.gffc6fa0e3

A message that is not in the archive (sent off-list or not yet received): 20190509105746.24830-2-jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org

Reviewed-by
#4 lore raw

Re: [PATCH 2/3] rk3399: nanopi4: Enable TPL

Hi Jagan,

Quoted 3 lines · Jagan Teki

Enable TPL for NanoPC T4, NanoPI M4 boards.

Signed-off-by Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
Reviewed-by Kever Yang <[email protected]>

Thanks,
- Kever

Quoted 81 lines
---
 configs/nanopc-t4-rk3399_defconfig | 7 ++++---
 configs/nanopi-m4-rk3399_defconfig | 7 ++++---
 2 files changed, 8 insertions(+), 6 deletions(-)
configs/nanopc-t4-rk3399_defconfig +4 -3
index d9f2137b4c..9b7e15d63a 100644
@@ -5,7 +5,7 @@ CONFIG_SPL_LIBCOMMON_SUPPORT=y
 CONFIG_SPL_LIBGENERIC_SUPPORT=y
 CONFIG_SYS_MALLOC_F_LEN=0x4000
 CONFIG_ROCKCHIP_RK3399=y
-CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x4000
+CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x50000
 CONFIG_DEBUG_UART_BASE=0xFF1A0000
 CONFIG_DEBUG_UART_CLOCK=24000000
 CONFIG_SPL_STACK_R_ADDR=0x80000

@@ -14,9 +14,8 @@ CONFIG_NR_DRAM_BANKS=1
 CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-nanopc-t4.dtb"
 # CONFIG_DISPLAY_CPUINFO is not set
 CONFIG_DISPLAY_BOARDINFO_LATE=y
-CONFIG_SPL_TEXT_BASE=0xff8c2000
 CONFIG_SPL_STACK_R=y
-CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x4000
+CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000
 CONFIG_CMD_BOOTZ=y
 CONFIG_CMD_GPT=y
 CONFIG_CMD_MMC=y

@@ -24,6 +23,7 @@ CONFIG_CMD_SF=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_TIME=y
+CONFIG_TPL=y
 CONFIG_SPL_OF_CONTROL=y
 CONFIG_DEFAULT_DEVICE_TREE="rk3399-nanopc-t4"
 CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"

@@ -56,4 +56,5 @@ CONFIG_USB_ETHER_MCS7830=y
 CONFIG_USB_ETHER_RTL8152=y
 CONFIG_USB_ETHER_SMSC95XX=y
 CONFIG_USE_TINY_PRINTF=y
+CONFIG_SPL_TINY_MEMSET=y
 CONFIG_ERRNO_STR=y
configs/nanopi-m4-rk3399_defconfig +4 -3
index c2832788f0..92e70dd939 100644
@@ -5,7 +5,7 @@ CONFIG_SPL_LIBCOMMON_SUPPORT=y
 CONFIG_SPL_LIBGENERIC_SUPPORT=y
 CONFIG_SYS_MALLOC_F_LEN=0x4000
 CONFIG_ROCKCHIP_RK3399=y
-CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x4000
+CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x50000
 CONFIG_DEBUG_UART_BASE=0xFF1A0000
 CONFIG_DEBUG_UART_CLOCK=24000000
 CONFIG_SPL_STACK_R_ADDR=0x80000

@@ -14,9 +14,8 @@ CONFIG_NR_DRAM_BANKS=1
 CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-nanopi-m4.dtb"
 # CONFIG_DISPLAY_CPUINFO is not set
 CONFIG_DISPLAY_BOARDINFO_LATE=y
-CONFIG_SPL_TEXT_BASE=0xff8c2000
 CONFIG_SPL_STACK_R=y
-CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x4000
+CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000
 CONFIG_CMD_BOOTZ=y
 CONFIG_CMD_GPT=y
 CONFIG_CMD_MMC=y

@@ -24,6 +23,7 @@ CONFIG_CMD_SF=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_TIME=y
+CONFIG_TPL=y
 CONFIG_SPL_OF_CONTROL=y
 CONFIG_DEFAULT_DEVICE_TREE="rk3399-nanopi-m4"
 CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"

@@ -56,4 +56,5 @@ CONFIG_USB_ETHER_MCS7830=y
 CONFIG_USB_ETHER_RTL8152=y
 CONFIG_USB_ETHER_SMSC95XX=y
 CONFIG_USE_TINY_PRINTF=y
+CONFIG_SPL_TINY_MEMSET=y
 CONFIG_ERRNO_STR=y
#5 lore raw

Re: [PATCH 2/3] rk3399: nanopi4: Enable TPL

Quoted 9 lines · Kever Yang

Hi Jagan,

Quoted 3 lines · Jagan Teki

Enable TPL for NanoPC T4, NanoPI M4 boards.

Signed-off-by Jagan Teki <[email protected]>
Reviewed-by Kever Yang <[email protected]>

Applied to u-boot-rockchip/master, thanks!

Quoted 83 lines

Thanks,
- Kever

Quoted 80 lines
---
 configs/nanopc-t4-rk3399_defconfig | 7 ++++---
 configs/nanopi-m4-rk3399_defconfig | 7 ++++---
 2 files changed, 8 insertions(+), 6 deletions(-)
configs/nanopc-t4-rk3399_defconfig +4 -3
index d9f2137b4c..9b7e15d63a 100644
@@ -5,7 +5,7 @@ CONFIG_SPL_LIBCOMMON_SUPPORT=y
 CONFIG_SPL_LIBGENERIC_SUPPORT=y
 CONFIG_SYS_MALLOC_F_LEN=0x4000
 CONFIG_ROCKCHIP_RK3399=y
-CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x4000
+CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x50000
 CONFIG_DEBUG_UART_BASE=0xFF1A0000
 CONFIG_DEBUG_UART_CLOCK=24000000
 CONFIG_SPL_STACK_R_ADDR=0x80000

@@ -14,9 +14,8 @@ CONFIG_NR_DRAM_BANKS=1
 CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-nanopc-t4.dtb"
 # CONFIG_DISPLAY_CPUINFO is not set
 CONFIG_DISPLAY_BOARDINFO_LATE=y
-CONFIG_SPL_TEXT_BASE=0xff8c2000
 CONFIG_SPL_STACK_R=y
-CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x4000
+CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000
 CONFIG_CMD_BOOTZ=y
 CONFIG_CMD_GPT=y
 CONFIG_CMD_MMC=y

@@ -24,6 +23,7 @@ CONFIG_CMD_SF=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_TIME=y
+CONFIG_TPL=y
 CONFIG_SPL_OF_CONTROL=y
 CONFIG_DEFAULT_DEVICE_TREE="rk3399-nanopc-t4"
 CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"

@@ -56,4 +56,5 @@ CONFIG_USB_ETHER_MCS7830=y
 CONFIG_USB_ETHER_RTL8152=y
 CONFIG_USB_ETHER_SMSC95XX=y
 CONFIG_USE_TINY_PRINTF=y
+CONFIG_SPL_TINY_MEMSET=y
 CONFIG_ERRNO_STR=y
configs/nanopi-m4-rk3399_defconfig +4 -3
index c2832788f0..92e70dd939 100644
@@ -5,7 +5,7 @@ CONFIG_SPL_LIBCOMMON_SUPPORT=y
 CONFIG_SPL_LIBGENERIC_SUPPORT=y
 CONFIG_SYS_MALLOC_F_LEN=0x4000
 CONFIG_ROCKCHIP_RK3399=y
-CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x4000
+CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x50000
 CONFIG_DEBUG_UART_BASE=0xFF1A0000
 CONFIG_DEBUG_UART_CLOCK=24000000
 CONFIG_SPL_STACK_R_ADDR=0x80000

@@ -14,9 +14,8 @@ CONFIG_NR_DRAM_BANKS=1
 CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-nanopi-m4.dtb"
 # CONFIG_DISPLAY_CPUINFO is not set
 CONFIG_DISPLAY_BOARDINFO_LATE=y
-CONFIG_SPL_TEXT_BASE=0xff8c2000
 CONFIG_SPL_STACK_R=y
-CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x4000
+CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000
 CONFIG_CMD_BOOTZ=y
 CONFIG_CMD_GPT=y
 CONFIG_CMD_MMC=y

@@ -24,6 +23,7 @@ CONFIG_CMD_SF=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_TIME=y
+CONFIG_TPL=y
 CONFIG_SPL_OF_CONTROL=y
 CONFIG_DEFAULT_DEVICE_TREE="rk3399-nanopi-m4"
 CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"

@@ -56,4 +56,5 @@ CONFIG_USB_ETHER_MCS7830=y
 CONFIG_USB_ETHER_RTL8152=y
 CONFIG_USB_ETHER_SMSC95XX=y
 CONFIG_USE_TINY_PRINTF=y
+CONFIG_SPL_TINY_MEMSET=y
Quoted 9 lines

configs/nanopi-m4-rk3399_defconfig CONFIG_USB_ETHER_MCS7830=y · line 60

Quoted 1 line
configs/nanopi-m4-rk3399_defconfig +0 -0
 CONFIG_ERRNO_STR=y

_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip

_______________________________________________
U-Boot mailing list
[email protected]
https://lists.denx.de/listinfo/u-boot

author
#6 lore raw

PATCH 3/3 doc: rockchip: Add doc for rk3399 TPL build/flash

In reply to a message not in the archive

This patch add documentation for TPL build and flashing steps for rk3399 boards.

Add full boot log for future reference.

Signed-off-by Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
---
 doc/README.rockchip | 51 ++++++++++++++++++++++++++++++++++++++++++++-
 1 file changed, 50 insertions(+), 1 deletion(-)
doc/README.rockchip +50 -1
index ca4d6473b0..264f7e4994 100644
@@ -173,7 +173,10 @@ For example:
      => make u-boot.itb
 
      (Get spl/u-boot-spl-dtb.bin, u-boot.itb images and some boards would get
-      spl/u-boot-spl.bin since it doesn't enable CONFIG_SPL_OF_CONTROL)
+      spl/u-boot-spl.bin since it doesn't enable CONFIG_SPL_OF_CONTROL
+
+      If TPL enabled on the target, get tpl/u-boot-tpl-dtb.bin or tpl/u-boot-tpl.bin
+      if CONFIG_TPL_OF_CONTROL not enabled)
 
 Writing to the board with USB
 =============================

@@ -455,6 +458,52 @@ Net:   eth0: ethernet@fe300000
 Hit any key to stop autoboot:  0
 =>
 
+Option 3: Package the image with TPL:
+
+  - Prefix rk3399 header to TPL image
+
+    => cd /path/to/u-boot
+    => ./tools/mkimage -n rk3399 -T rksd -d tpl/u-boot-tpl-dtb.bin out
+
+  - Concatinate tpl with spl
+
+    => cd /path/to/u-boot
+    => cat ./spl/u-boot-spl-dtb.bin >> out
+
+  - Write tpl+spl at 64th sector
+
+    => sudo dd if=out of=/dev/sdc seek=64
+
+  - Write U-Boot proper at 16384 sector
+
+    => sudo dd if=u-boot.itb of=/dev/sdc seek=16384
+    => sync
+
+Put this SD (or micro-SD) card into your board and reset it. You should see
+something like:
+
+U-Boot TPL board init
+Trying to boot from BOOTROM
+Returning to boot ROM...
+
+U-Boot SPL board init
+Trying to boot from MMC1
+
+
+U-Boot 2019.07-rc1-00241-g5b3244767a (May 08 2019 - 10:51:06 +0530)
+
+Model: Orange Pi RK3399 Board
+DRAM:  2 GiB
+MMC:   dwmmc@fe310000: 2, dwmmc@fe320000: 1, sdhci@fe330000: 0
+Loading Environment from MMC... OK
+In:    serial@ff1a0000
+Out:   serial@ff1a0000
+Err:   serial@ff1a0000
+Model: Orange Pi RK3399 Board
+Net:   eth0: ethernet@fe300000
+Hit any key to stop autoboot:  0
+=>
+
 Using fastboot on rk3288
 ========================
 - Write GPT partition layout to mmc device which fastboot want to use it to
Signature · 1 line
2.18.0.321.gffc6fa0e3

A message that is not in the archive (sent off-list or not yet received): 20190509105746.24830-3-jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org

Reviewed-by
#8 lore raw

Re: [PATCH 3/3] doc: rockchip: Add doc for rk3399 TPL build/flash

Hi Jagan,

Quoted 6 lines · Jagan Teki

This patch add documentation for TPL build and flashing steps for rk3399 boards.

Add full boot log for future reference.

Signed-off-by Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
Reviewed-by Kever Yang <[email protected]>

Thanks,
- Kever

Quoted 73 lines
---
 doc/README.rockchip | 51 ++++++++++++++++++++++++++++++++++++++++++++-
 1 file changed, 50 insertions(+), 1 deletion(-)
doc/README.rockchip +50 -1
index ca4d6473b0..264f7e4994 100644
@@ -173,7 +173,10 @@ For example:
      => make u-boot.itb
 
      (Get spl/u-boot-spl-dtb.bin, u-boot.itb images and some boards would get
-      spl/u-boot-spl.bin since it doesn't enable CONFIG_SPL_OF_CONTROL)
+      spl/u-boot-spl.bin since it doesn't enable CONFIG_SPL_OF_CONTROL
+
+      If TPL enabled on the target, get tpl/u-boot-tpl-dtb.bin or tpl/u-boot-tpl.bin
+      if CONFIG_TPL_OF_CONTROL not enabled)
 
 Writing to the board with USB
 =============================

@@ -455,6 +458,52 @@ Net:   eth0: ethernet@fe300000
 Hit any key to stop autoboot:  0
 =>
 
+Option 3: Package the image with TPL:
+
+  - Prefix rk3399 header to TPL image
+
+    => cd /path/to/u-boot
+    => ./tools/mkimage -n rk3399 -T rksd -d tpl/u-boot-tpl-dtb.bin out
+
+  - Concatinate tpl with spl
+
+    => cd /path/to/u-boot
+    => cat ./spl/u-boot-spl-dtb.bin >> out
+
+  - Write tpl+spl at 64th sector
+
+    => sudo dd if=out of=/dev/sdc seek=64
+
+  - Write U-Boot proper at 16384 sector
+
+    => sudo dd if=u-boot.itb of=/dev/sdc seek=16384
+    => sync
+
+Put this SD (or micro-SD) card into your board and reset it. You should see
+something like:
+
+U-Boot TPL board init
+Trying to boot from BOOTROM
+Returning to boot ROM...
+
+U-Boot SPL board init
+Trying to boot from MMC1
+
+
+U-Boot 2019.07-rc1-00241-g5b3244767a (May 08 2019 - 10:51:06 +0530)
+
+Model: Orange Pi RK3399 Board
+DRAM:  2 GiB
+MMC:   dwmmc@fe310000: 2, dwmmc@fe320000: 1, sdhci@fe330000: 0
+Loading Environment from MMC... OK
+In:    serial@ff1a0000
+Out:   serial@ff1a0000
+Err:   serial@ff1a0000
+Model: Orange Pi RK3399 Board
+Net:   eth0: ethernet@fe300000
+Hit any key to stop autoboot:  0
+=>
+
 Using fastboot on rk3288
 ========================
 - Write GPT partition layout to mmc device which fastboot want to use it to

A message that is not in the archive (sent off-list or not yet received): b5cd9180-56c9-dd02-e6bf-4e7638902d5c-TNX95d0MmH7DzftRWevZcw@public.gmane.org

#10 lore raw

Re: [PATCH 3/3] doc: rockchip: Add doc for rk3399 TPL build/flash

Quoted 11 lines · Kever Yang

Hi Jagan,

Quoted 6 lines · Jagan Teki

This patch add documentation for TPL build and flashing steps for rk3399 boards.

Add full boot log for future reference.

Signed-off-by Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
Reviewed-by Kever Yang <[email protected]>

Applied to u-boot-rockchip/master, thanks!

Quoted 84 lines

Thanks,
- Kever

Quoted 63 lines
---
 doc/README.rockchip | 51 ++++++++++++++++++++++++++++++++++++++++++++-
 1 file changed, 50 insertions(+), 1 deletion(-)
doc/README.rockchip +43 -1
index ca4d6473b0..264f7e4994 100644
@@ -173,7 +173,10 @@ For example:
      => make u-boot.itb
 
      (Get spl/u-boot-spl-dtb.bin, u-boot.itb images and some boards would get
-      spl/u-boot-spl.bin since it doesn't enable CONFIG_SPL_OF_CONTROL)
+      spl/u-boot-spl.bin since it doesn't enable CONFIG_SPL_OF_CONTROL
+
+      If TPL enabled on the target, get tpl/u-boot-tpl-dtb.bin or tpl/u-boot-tpl.bin
+      if CONFIG_TPL_OF_CONTROL not enabled)
 
 Writing to the board with USB
 =============================

@@ -455,6 +458,52 @@ Net:   eth0: ethernet@fe300000
 Hit any key to stop autoboot:  0
 =>
 
+Option 3: Package the image with TPL:
+
+  - Prefix rk3399 header to TPL image
+
+    => cd /path/to/u-boot
+    => ./tools/mkimage -n rk3399 -T rksd -d tpl/u-boot-tpl-dtb.bin out
+
+  - Concatinate tpl with spl
+
+    => cd /path/to/u-boot
+    => cat ./spl/u-boot-spl-dtb.bin >> out
+
+  - Write tpl+spl at 64th sector
+
+    => sudo dd if=out of=/dev/sdc seek=64
+
+  - Write U-Boot proper at 16384 sector
+
+    => sudo dd if=u-boot.itb of=/dev/sdc seek=16384
+    => sync
+
+Put this SD (or micro-SD) card into your board and reset it. You should see
+something like:
+
+U-Boot TPL board init
+Trying to boot from BOOTROM
+Returning to boot ROM...
+
+U-Boot SPL board init
+Trying to boot from MMC1
+
+
+U-Boot 2019.07-rc1-00241-g5b3244767a (May 08 2019 - 10:51:06 +0530)
+
+Model: Orange Pi RK3399 Board
+DRAM:  2 GiB
+MMC:   dwmmc@fe310000: 2, dwmmc@fe320000: 1, sdhci@fe330000: 0
+Loading Environment from MMC... OK
+In:    serial@ff1a0000

doc/README.rockchip Net: eth0: ethernet@fe300000 · line 509

Quoted 10 lines
doc/README.rockchip +7 -0
+Out:   serial@ff1a0000
+Err:   serial@ff1a0000
+Model: Orange Pi RK3399 Board
+Net:   eth0: ethernet@fe300000
+Hit any key to stop autoboot:  0
+=>
+
 Using fastboot on rk3288
 ========================
 - Write GPT partition layout to mmc device which fastboot want to use it to

_______________________________________________
Linux-rockchip mailing list [email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip

#11 lore raw
In reply to a message not in the archive

Hi Jagan,

    The first two patches need re-base after the patch from Tom:

344a0e4367 configs: Resync with savedefconfig

Thanks,
- Kever

Quoted 40 lines · Jagan Teki

Enable TPL for OrangePI rk3399 board.

Signed-off-by Jagan Teki <[email protected]>
---
 configs/orangepi-rk3399_defconfig | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)
configs/orangepi-rk3399_defconfig +3 -3
index 3f02c89983..90021bb695 100644
@@ -5,7 +5,7 @@ CONFIG_SPL_LIBCOMMON_SUPPORT=y
 CONFIG_SPL_LIBGENERIC_SUPPORT=y
 CONFIG_SYS_MALLOC_F_LEN=0x4000
 CONFIG_ROCKCHIP_RK3399=y
-CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x4000
+CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x50000
 CONFIG_DEBUG_UART_BASE=0xFF1A0000
 CONFIG_DEBUG_UART_CLOCK=24000000
 CONFIG_SPL_STACK_R_ADDR=0x80000

@@ -14,9 +14,8 @@ CONFIG_NR_DRAM_BANKS=1
 CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-orangepi.dtb"
 # CONFIG_DISPLAY_CPUINFO is not set
 CONFIG_DISPLAY_BOARDINFO_LATE=y
-CONFIG_SPL_TEXT_BASE=0xff8c2000
 CONFIG_SPL_STACK_R=y
-CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x4000
+CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000
 CONFIG_CMD_BOOTZ=y
 CONFIG_CMD_GPT=y
 CONFIG_CMD_MMC=y

@@ -24,6 +23,7 @@ CONFIG_CMD_SF=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_TIME=y
+CONFIG_TPL=y
 CONFIG_SPL_OF_CONTROL=y
 CONFIG_DEFAULT_DEVICE_TREE="rk3399-orangepi"
 CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"

configs/orangepi-rk3399_defconfig CONFIG_USB_ETHER_MCS7830=y · line 60

Quoted 5 lines
configs/orangepi-rk3399_defconfig +1 -0
@@ -56,4 +56,5 @@ CONFIG_USB_ETHER_MCS7830=y
 CONFIG_USB_ETHER_RTL8152=y
 CONFIG_USB_ETHER_SMSC95XX=y
 CONFIG_USE_TINY_PRINTF=y
+CONFIG_SPL_TINY_MEMSET=y
 CONFIG_ERRNO_STR=y

_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip

Reviewed-by on v1 1/3
#12 lore raw
In reply to Jagan Teki

Hi Jagan,

Quoted 3 lines · Jagan Teki

Enable TPL for OrangePI rk3399 board.

Signed-off-by Jagan Teki <[email protected]>
Reviewed-by Kever Yang <[email protected]>

Thanks,
- Kever

Quoted 37 lines
---
 configs/orangepi-rk3399_defconfig | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)
configs/orangepi-rk3399_defconfig +3 -3
index 3f02c89983..90021bb695 100644
@@ -5,7 +5,7 @@ CONFIG_SPL_LIBCOMMON_SUPPORT=y
 CONFIG_SPL_LIBGENERIC_SUPPORT=y
 CONFIG_SYS_MALLOC_F_LEN=0x4000
 CONFIG_ROCKCHIP_RK3399=y
-CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x4000
+CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x50000
 CONFIG_DEBUG_UART_BASE=0xFF1A0000
 CONFIG_DEBUG_UART_CLOCK=24000000
 CONFIG_SPL_STACK_R_ADDR=0x80000

@@ -14,9 +14,8 @@ CONFIG_NR_DRAM_BANKS=1
 CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-orangepi.dtb"
 # CONFIG_DISPLAY_CPUINFO is not set
 CONFIG_DISPLAY_BOARDINFO_LATE=y
-CONFIG_SPL_TEXT_BASE=0xff8c2000
 CONFIG_SPL_STACK_R=y
-CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x4000
+CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000
 CONFIG_CMD_BOOTZ=y
 CONFIG_CMD_GPT=y
 CONFIG_CMD_MMC=y

@@ -24,6 +23,7 @@ CONFIG_CMD_SF=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_TIME=y
+CONFIG_TPL=y
 CONFIG_SPL_OF_CONTROL=y
 CONFIG_DEFAULT_DEVICE_TREE="rk3399-orangepi"
 CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"

configs/orangepi-rk3399_defconfig CONFIG_USB_ETHER_MCS7830=y · line 60

Quoted 5 lines
configs/orangepi-rk3399_defconfig +1 -0
@@ -56,4 +56,5 @@ CONFIG_USB_ETHER_MCS7830=y
 CONFIG_USB_ETHER_RTL8152=y
 CONFIG_USB_ETHER_SMSC95XX=y
 CONFIG_USE_TINY_PRINTF=y
+CONFIG_SPL_TINY_MEMSET=y
 CONFIG_ERRNO_STR=y

_______________________________________________
U-Boot mailing list
[email protected]
https://lists.denx.de/listinfo/u-boot

A message that is not in the archive (sent off-list or not yet received): 3d1513a8-202a-9906-ddb0-2ed1000696f3-TNX95d0MmH7DzftRWevZcw@public.gmane.org

#14 lore raw
Quoted 8 lines · Kever Yang

Hi Jagan,

Quoted 3 lines · Jagan Teki

Enable TPL for OrangePI rk3399 board.

Signed-off-by Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
Reviewed-by Kever Yang <[email protected]>

Applied to u-boot-rockchip/master, thanks!

Quoted 53 lines

Thanks,
- Kever

Quoted 37 lines
---
 configs/orangepi-rk3399_defconfig | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)
configs/orangepi-rk3399_defconfig +3 -3
index 3f02c89983..90021bb695 100644
@@ -5,7 +5,7 @@ CONFIG_SPL_LIBCOMMON_SUPPORT=y
 CONFIG_SPL_LIBGENERIC_SUPPORT=y
 CONFIG_SYS_MALLOC_F_LEN=0x4000
 CONFIG_ROCKCHIP_RK3399=y
-CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x4000
+CONFIG_ROCKCHIP_SPL_RESERVE_IRAM=0x50000
 CONFIG_DEBUG_UART_BASE=0xFF1A0000
 CONFIG_DEBUG_UART_CLOCK=24000000
 CONFIG_SPL_STACK_R_ADDR=0x80000

@@ -14,9 +14,8 @@ CONFIG_NR_DRAM_BANKS=1
 CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-orangepi.dtb"
 # CONFIG_DISPLAY_CPUINFO is not set
 CONFIG_DISPLAY_BOARDINFO_LATE=y
-CONFIG_SPL_TEXT_BASE=0xff8c2000
 CONFIG_SPL_STACK_R=y
-CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x4000
+CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000
 CONFIG_CMD_BOOTZ=y
 CONFIG_CMD_GPT=y
 CONFIG_CMD_MMC=y

@@ -24,6 +23,7 @@ CONFIG_CMD_SF=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_TIME=y
+CONFIG_TPL=y
 CONFIG_SPL_OF_CONTROL=y
 CONFIG_DEFAULT_DEVICE_TREE="rk3399-orangepi"
 CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"

configs/orangepi-rk3399_defconfig CONFIG_USB_ETHER_MCS7830=y · line 60

Quoted 5 lines
configs/orangepi-rk3399_defconfig +1 -0
@@ -56,4 +56,5 @@ CONFIG_USB_ETHER_MCS7830=y
 CONFIG_USB_ETHER_RTL8152=y
 CONFIG_USB_ETHER_SMSC95XX=y
 CONFIG_USE_TINY_PRINTF=y
+CONFIG_SPL_TINY_MEMSET=y
 CONFIG_ERRNO_STR=y

_______________________________________________
Linux-rockchip mailing list [email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip