Skip to contentSkip to conversation

ARC: [plat-hsdk] Get rid of inappropriate PHY settings

PATCH In review Alexey Brodkin 3 participants 3 messages May 15, 2019 – May 28, 2019

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 ARC: [plat-hsdk] Get rid of inappropriate PHY settings

Initial bring-up of the platform was done on FPGA prototype where TI's DP83867 PHY was used. And so some specific PHY options were added.

Just to confirm this is what we get on FPGA prototype in the bootlog:
| TI DP83867 stmmac-0:00: attached PHY driver [TI DP83867] ...

On real board though we have Micrel KZS9031 PHY and we even have CONFIG_MICREL_PHY=y set in hsdk_defconfig. That's what we see in the bootlog:
| Micrel KSZ9031 Gigabit PHY stmmac-0:00: ...

So essentially all TI-related bits have to go away.

Signed-off-by Alexey Brodkin <abrodkin at synopsys.com>
Cc Trent Piepho <tpiepho at impinj.com>
Cc Rob Herring <robh+dt at kernel.org>
---
 arch/arc/boot/dts/hsdk.dts | 4 ----
 1 file changed, 4 deletions(-)
arch/arc/boot/dts/hsdk.dts +0 -4
index 7425bb0f2d1b..f88a898029ce 100644
@@ -11,7 +11,6 @@
  */
 /dts-v1/;
 
-#include <dt-bindings/net/ti-dp83867.h>
 #include <dt-bindings/reset/snps,hsdk-reset.h>
 
 / {
@@ -201,9 +200,6 @@
 				compatible = "snps,dwmac-mdio";
 				phy0: ethernet-phy at 0 {
 					reg = <0>;
-					ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
-					ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
-					ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
 				};
 			};
 		};
Signature · 1 line
2.16.2
Acked-by on v1 1/1
#1 lore raw
Quoted 9 lines · Alexey Brodkin

Initial bring-up of the platform was done on FPGA prototype where TI's DP83867 PHY was used. And so some specific PHY options were added.

Just to confirm this is what we get on FPGA prototype in the bootlog:

Quoted 1 line

TI DP83867 stmmac-0:00: attached PHY driver [TI DP83867] ...

On real board though we have Micrel KZS9031 PHY and we even have CONFIG_MICREL_PHY=y set in hsdk_defconfig. That's what we see in the bootlog:

Quoted 7 lines
Quoted 1 line

Micrel KSZ9031 Gigabit PHY stmmac-0:00: ...

So essentially all TI-related bits have to go away.

Signed-off-by Alexey Brodkin <abrodkin at synopsys.com>
Cc Trent Piepho <tpiepho at impinj.com>
Cc Rob Herring <robh+dt at kernel.org>
Acked-by <tpiepho at impinj.com>

Review

Quoted 5 lines
---
 arch/arc/boot/dts/hsdk.dts | 4 ----
 1 file changed, 4 deletions(-)
(quoted diff) +0 -0
@@ -201,9 +200,6 @@

I think it would be pedantically correct to change the phy-mode to "rgmii-id", though I see nothing in the micrel phy driver that uses this, and so doubt it will do anything at all at this point.

The Micrel phy appears to default to putting a clock skew on the RGMII lines and the driver will use the default if no properties are present. So I believe what your board is effectively using now is "rgmii-id" with default skews, unless the phy and your board design has some resistor pin strapping that has changed this.

#2 lore raw
In reply to Alexey Brodkin
Quoted 11 lines · Alexey Brodkin

Initial bring-up of the platform was done on FPGA prototype where TI's DP83867 PHY was used. And so some specific PHY options were added.

Just to confirm this is what we get on FPGA prototype in the bootlog:
| TI DP83867 stmmac-0:00: attached PHY driver [TI DP83867] ...

On real board though we have Micrel KZS9031 PHY and we even have CONFIG_MICREL_PHY=y set in hsdk_defconfig. That's what we see in the bootlog:
| Micrel KSZ9031 Gigabit PHY stmmac-0:00: ...

Quoted 5 lines

So essentially all TI-related bits have to go away.

Signed-off-by Alexey Brodkin <abrodkin at synopsys.com>
Cc Trent Piepho <tpiepho at impinj.com>
Cc Rob Herring <robh+dt at kernel.org>

Added to for-curr.

Thx,
-Vineet