Skip to contentSkip to conversation

add thermal driver for h6

PATCH Superseded Yangtao Li 3 participants 5 messages May 16, 2019 – May 17, 2019

Subsystems (4)

v2 of 5 Superseded Latest is v5 →

lore
Share & tools
lore

Yangtao Li

author maintainer
#0 lore raw

v2 cover add thermal driver for h6

This patchset supprt H6 thermal controller.

Yangtao Li (2):
thermal: sun8i: add thermal driver for h6
dt-bindings: thermal: add binding document for h6 thermal controller

 .../bindings/thermal/sun8i-thermal.txt        |  34 ++
 MAINTAINERS                                   |   7 +
 drivers/thermal/Kconfig                       |  14 +
 drivers/thermal/Makefile                      |   1 +
 drivers/thermal/sun8i_thermal.c               | 422 ++++++++++++++++++
 5 files changed, 478 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/thermal/sun8i-thermal.txt
 create mode 100644 drivers/thermal/sun8i_thermal.c

---
v2:
-Additions and deletions of some comments
-Change some function prefix to "ths_"
-Support interrupt
---
2.17.0

author maintainer
#1 lore raw

PATCH v2 1/2 thermal: sun8i: add thermal driver for h6

This patch adds the support for allwinner thermal sensor, within allwinner SoC. It will register sensors for thermal framework and use device tree to bind cooling device.

---
 MAINTAINERS                     |   7 +
 drivers/thermal/Kconfig         |  14 ++
 drivers/thermal/Makefile        |   1 +
 drivers/thermal/sun8i_thermal.c | 422 ++++++++++++++++++++++++++++++++
 4 files changed, 444 insertions(+)
 create mode 100644 drivers/thermal/sun8i_thermal.c
MAINTAINERS +7 -0
index 005902ea1450..4e753ed20cd0 100644
@@ -674,6 +674,13 @@ L:	[email protected]
 S:	Maintained
 F:	drivers/crypto/sunxi-ss/
 
+ALLWINNER THERMAL DRIVER
+M:	Yangtao Li <[email protected]>
+L:	[email protected]
+S:	Maintained
+F:	Documentation/devicetree/bindings/thermal/sun8i-thermal.txt
+F:	drivers/thermal/sun8i_thermal.c
+
 ALLWINNER VPU DRIVER
 M:	Maxime Ripard <[email protected]>
 M:	Paul Kocialkowski <[email protected]>
drivers/thermal/Kconfig +14 -0
index 66a709d5d6b9..f03d941c5686 100644
@@ -263,6 +263,20 @@ config SPEAR_THERMAL
 	  Enable this to plug the SPEAr thermal sensor driver into the Linux
 	  thermal framework.
 
+config SUN8I_THERMAL
+	tristate "Allwinner sun8i thermal driver"
+	depends on ARCH_SUNXI || COMPILE_TEST
+	depends on HAS_IOMEM
+	depends on NVMEM_SUNXI_SID
+	depends on OF
+	depends on RESET_CONTROLLER
+	help
+	  Support for the sun8i thermal sensor driver into the Linux thermal
+	  framework.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called sun8i-thermal.
+
 config ROCKCHIP_THERMAL
 	tristate "Rockchip thermal driver"
 	depends on ARCH_ROCKCHIP || COMPILE_TEST
drivers/thermal/Makefile +1 -0
index 74a37c7f847a..fa6f8b206281 100644
@@ -31,6 +31,7 @@ thermal_sys-$(CONFIG_DEVFREQ_THERMAL) += devfreq_cooling.o
 obj-y				+= broadcom/
 obj-$(CONFIG_THERMAL_MMIO)		+= thermal_mmio.o
 obj-$(CONFIG_SPEAR_THERMAL)	+= spear_thermal.o
+obj-$(CONFIG_SUN8I_THERMAL)     += sun8i_thermal.o
 obj-$(CONFIG_ROCKCHIP_THERMAL)	+= rockchip_thermal.o
 obj-$(CONFIG_RCAR_THERMAL)	+= rcar_thermal.o
 obj-$(CONFIG_RCAR_GEN3_THERMAL)	+= rcar_gen3_thermal.o
drivers/thermal/sun8i_thermal.c new file +422 -0

422 lines not on this page · raw message

Signature · 1 line
2.17.0
author maintainer
#3 lore raw

PATCH v2 2/2 dt-bindings: thermal: add binding document for h6 thermal controller

In reply to Yangtao Li

This patch adds binding document for allwinner h6 thermal controller.

---
 .../bindings/thermal/sun8i-thermal.txt        | 34 +++++++++++++++++++
 1 file changed, 34 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/thermal/sun8i-thermal.txt
Documentation/devicetree/bindings/thermal/sun8i-thermal.txt new file +34 -0
new file mode 100644
index 000000000000..bd417260501f
@@ -0,0 +1,34 @@
+* Allwinner Thermal
+
+This describes the device tree binding for the Allwinner thermal controller
+which measures the on-SoC temperatures.
+
+Required properties:
+- compatible:
+  - "allwinner,sun50i-h6-ths" : For H6
+- reg: Address range of the thermal controller
+- clocks, clock-names: Clocks needed for the thermal controller.
+		       The required clocks for h6 are: "bus".
+- resets: Reference to the reset controller controlling the thermal controller.
+- interrupts: IRQ for the thermal controller
+- #thermal-sensor-cells : For H6 Should be 1.
+			  See ./thermal.txt for a description.
+
+Optional properties:
+- nvmem-cells: A phandle to the calibration data provided by a nvmem device. If
+	       unspecified default values shall be used.
+- nvmem-cell-names: Should be "calib".
+
+Example:
+
+	ths: ths@1c25000 {
+		compatible = "allwinner,sun50i-h6-ths";
+		reg = <0x05070400 0x100>;
+		clocks = <&ccu CLK_BUS_THS>;
+		clock-names = "bus";
+		resets = <&ccu RST_BUS_THS>;
+		interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+		nvmem-cells = <&tsen_calib>;
+		nvmem-cell-names = "calib";
+		#thermal-sensor-cells = <1>;
+	};
Signature · 1 line
2.17.0
#2 lore raw

Re: [PATCH v2 1/2] thermal: sun8i: add thermal driver for h6

In reply to Yangtao Li

Hello Yangtao,

Quoted 158 lines · Yangtao Li

This patch adds the support for allwinner thermal sensor, within allwinner SoC. It will register sensors for thermal framework and use device tree to bind cooling device.

---
 MAINTAINERS                     |   7 +
 drivers/thermal/Kconfig         |  14 ++
 drivers/thermal/Makefile        |   1 +
 drivers/thermal/sun8i_thermal.c | 422 ++++++++++++++++++++++++++++++++
 4 files changed, 444 insertions(+)
 create mode 100644 drivers/thermal/sun8i_thermal.c
MAINTAINERS +7 -0
index 005902ea1450..4e753ed20cd0 100644
@@ -674,6 +674,13 @@ L:	[email protected]
 S:	Maintained
 F:	drivers/crypto/sunxi-ss/
 
+ALLWINNER THERMAL DRIVER
+M:	Yangtao Li <[email protected]>
+L:	[email protected]
+S:	Maintained
+F:	Documentation/devicetree/bindings/thermal/sun8i-thermal.txt
+F:	drivers/thermal/sun8i_thermal.c
+
 ALLWINNER VPU DRIVER
 M:	Maxime Ripard <[email protected]>
 M:	Paul Kocialkowski <[email protected]>
drivers/thermal/Kconfig +14 -0
index 66a709d5d6b9..f03d941c5686 100644
@@ -263,6 +263,20 @@ config SPEAR_THERMAL
 	  Enable this to plug the SPEAr thermal sensor driver into the Linux
 	  thermal framework.
 
+config SUN8I_THERMAL
+	tristate "Allwinner sun8i thermal driver"
+	depends on ARCH_SUNXI || COMPILE_TEST
+	depends on HAS_IOMEM
+	depends on NVMEM_SUNXI_SID
+	depends on OF
+	depends on RESET_CONTROLLER
+	help
+	  Support for the sun8i thermal sensor driver into the Linux thermal
+	  framework.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called sun8i-thermal.
+
 config ROCKCHIP_THERMAL
 	tristate "Rockchip thermal driver"
 	depends on ARCH_ROCKCHIP || COMPILE_TEST
drivers/thermal/Makefile +1 -0
index 74a37c7f847a..fa6f8b206281 100644
@@ -31,6 +31,7 @@ thermal_sys-$(CONFIG_DEVFREQ_THERMAL) += devfreq_cooling.o
 obj-y				+= broadcom/
 obj-$(CONFIG_THERMAL_MMIO)		+= thermal_mmio.o
 obj-$(CONFIG_SPEAR_THERMAL)	+= spear_thermal.o
+obj-$(CONFIG_SUN8I_THERMAL)     += sun8i_thermal.o
 obj-$(CONFIG_ROCKCHIP_THERMAL)	+= rockchip_thermal.o
 obj-$(CONFIG_RCAR_THERMAL)	+= rcar_thermal.o
 obj-$(CONFIG_RCAR_GEN3_THERMAL)	+= rcar_gen3_thermal.o
drivers/thermal/sun8i_thermal.c new file +84 -0
new file mode 100644
index 000000000000..c9920f58fc80
@@ -0,0 +1,422 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Thermal sensor driver for Allwinner SOC
+ * Copyright (C) 2019 Yangtao Li
+ *
+ * Based on the work of Icenowy Zheng <[email protected]>
+ * Based on the work of Ondrej Jirman <[email protected]>
+ * Based on the work of Josef Gajdusek <[email protected]>
+ */
+
+#include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/nvmem-consumer.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+#include <linux/slab.h>
+#include <linux/thermal.h>
+
+#define MAX_SENSOR_NUM	4
+
+#define FT_TEMP_MASK				GENMASK(11, 0)
+#define TEMP_CALIB_MASK				GENMASK(11, 0)
+#define TEMP_TO_REG				672
+#define CALIBRATE_DEFAULT			0x800
+
+#define SUN50I_THS_CTRL0			0x00
+#define SUN50I_H6_THS_ENABLE			0x04
+#define SUN50I_H6_THS_PC			0x08
+#define SUN50I_H6_THS_DIC			0x10
+#define SUN50I_H6_THS_DIS			0x20
+#define SUN50I_H6_THS_MFC			0x30
+#define SUN50I_H6_THS_TEMP_CALIB		0xa0
+#define SUN50I_H6_THS_TEMP_DATA			0xc0
+
+#define SUN50I_THS_CTRL0_T_ACQ(x)		((GENMASK(15, 0) & (x)) << 16)
+#define SUN50I_THS_FILTER_EN			BIT(2)
+#define SUN50I_THS_FILTER_TYPE(x)		(GENMASK(1, 0) & (x))
+#define SUN50I_H6_THS_PC_TEMP_PERIOD(x)		((GENMASK(19, 0) & (x)) << 12)
+#define SUN50I_H6_THS_DATA_IRQ_STS(x)		BIT(x)
+
+/* millidegree celsius */
+#define SUN50I_H6_FT_DEVIATION			7000
+
+struct ths_device;
+
+struct tsensor {
+	struct ths_device		*tmdev;
+	struct thermal_zone_device	*tzd;
+	int				id;
+};
+
+struct ths_thermal_chip {
+	int		sensor_num;
+	int		offset;
+	int		scale;
+	int		ft_deviation;
+	int		temp_calib_base;
+	int		temp_data_base;
+	int		(*enable)(struct ths_device *tmdev);
+	int		(*disable)(struct ths_device *tmdev);
+	irqreturn_t	(*irq_thread)(int irq, void *data);
+};
+
+struct ths_device {
+	const struct ths_thermal_chip		*chip;
+	struct device				*dev;
+	struct regmap				*regmap;
+	struct reset_control			*reset;
+	struct clk				*bus_clk;
+	struct tsensor				sensor[MAX_SENSOR_NUM];
+};
+
+/* Temp Unit: millidegree Celsius */
+static int ths_reg2temp(struct ths_device *tmdev,
+			int reg)
+{
+	return (reg + tmdev->chip->offset) * tmdev->chip->scale;
+}
+
+static int ths_get_temp(void *data, int *temp)

drivers/thermal/sun8i_thermal.c line 94

Quoted 10 lines
drivers/thermal/sun8i_thermal.c new file +10 -0
+{
+	struct tsensor *s = data;
+	struct ths_device *tmdev = s->tmdev;
+	int val;
+
+	regmap_read(tmdev->regmap, tmdev->chip->temp_data_base +
+		    0x4 * s->id, &val);
+
+	/* ths have no data yet */
+	if (unlikely(val == 0))

You probably forgot to change this to !val and drop unlikely.

drivers/thermal/sun8i_thermal.c line 99

Quoted 5 lines
drivers/thermal/sun8i_thermal.c new file +5 -0
+		return -EBUSY;
+
+	*temp = ths_reg2temp(tmdev, val);
+	if (tmdev->chip->ft_deviation)
+		*temp += tmdev->chip->ft_deviation;

Please move this to ths_reg2temp, so that ths_reg2temp returns the final temperature.

Quoted 240 lines
drivers/thermal/sun8i_thermal.c new file +240 -0
+	return 0;
+}
+
+static const struct thermal_zone_of_device_ops ths_ops = {
+	.get_temp = ths_get_temp,
+};
+
+static const struct regmap_config config = {
+	.reg_bits = 32,
+	.val_bits = 32,
+	.reg_stride = 4,
+	.fast_io = true,
+};
+
+static irqreturn_t sun50i_h6_irq_thread(int irq, void *data)
+{
+	struct ths_device *tmdev = data;
+	int i, state;
+
+	regmap_read(tmdev->regmap, SUN50I_H6_THS_DIS, &state);
+
+	for (i = 0; i < tmdev->chip->sensor_num; i++) {
+		if (state & SUN50I_H6_THS_DATA_IRQ_STS(i)) {
+			/* clear data irq pending */
+			regmap_write(tmdev->regmap, SUN50I_H6_THS_DIS,
+				     SUN50I_H6_THS_DATA_IRQ_STS(i));
+
+			thermal_zone_device_update(tmdev->sensor[i].tzd,
+						   THERMAL_EVENT_UNSPECIFIED);
+		}
+	}
+
+	return IRQ_HANDLED;
+}
+
+static int ths_init_resource(struct ths_device *tmdev)
+{
+	struct device *dev = tmdev->dev;
+	struct platform_device *pdev = to_platform_device(dev);
+	struct resource *mem;
+	void __iomem *base;
+	int irq, ret;
+
+	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	base = devm_ioremap_resource(dev, mem);
+	if (IS_ERR(base))
+		return PTR_ERR(base);
+
+	tmdev->regmap = devm_regmap_init_mmio(dev, base, &config);
+	if (IS_ERR(tmdev->regmap))
+		return PTR_ERR(tmdev->regmap);
+
+	tmdev->reset = devm_reset_control_get(dev, 0);
+	if (IS_ERR(tmdev->reset))
+		return PTR_ERR(tmdev->reset);
+
+	tmdev->bus_clk = devm_clk_get(&pdev->dev, "bus");
+	if (IS_ERR(tmdev->bus_clk))
+		return PTR_ERR(tmdev->bus_clk);
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0)
+		return irq;
+
+	ret = devm_request_threaded_irq(dev, irq, NULL,
+					tmdev->chip->irq_thread,
+					IRQF_ONESHOT, "ths", tmdev);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static int ths_calibrate(struct ths_device *tmdev)
+{
+	struct nvmem_cell *calcell;
+	struct device *dev = tmdev->dev;
+	u16 *caldata;
+	size_t callen;
+	int ft_temp;
+	int i, ret = 0;
+
+	calcell = devm_nvmem_cell_get(dev, "calib");
+	if (IS_ERR(calcell)) {
+		if (PTR_ERR(calcell) == -EPROBE_DEFER)
+			return -EPROBE_DEFER;
+		/*
+		 * Even if the external calibration data stored in sid is
+		 * not accessible, the THS hardware can still work, although
+		 * the data won't be so accurate.
+		 *
+		 * The default value of calibration register is 0x800 for
+		 * every sensor, and the calibration value is usually 0x7xx
+		 * or 0x8xx, so they won't be away from the default value
+		 * for a lot.
+		 *
+		 * So here we do not return error if the calibartion data is
+		 * not available, except the probe needs deferring.
+		 */
+		goto out;
+	}
+
+	caldata = nvmem_cell_read(calcell, &callen);
+	if (IS_ERR(caldata)) {
+		ret = PTR_ERR(caldata);
+		goto out;
+	}
+
+	if (!caldata[0] || callen < 2 + 2 * tmdev->chip->sensor_num) {
+		ret = -EINVAL;
+		goto out_free;
+	}
+
+	/*
+	 * efuse layout:
+	 *
+	 *	0   11  16	 32
+	 *	+-------+-------+-------+
+	 *	|temp|  |sensor0|sensor1|
+	 *	+-------+-------+-------+
+	 *
+	 * The calibration data on the H6 is the ambient temperature and
+	 * sensor values that are filled during the factory test stage.
+	 *
+	 * The unit of stored FT temperature is 0.1 degreee celusis.
+	 * Through the stored ambient temperature and the data read
+	 * by the sensor, after a certain calculation, the calibration
+	 * value to be compensated can be obtained.
+	 */
+	ft_temp = caldata[0] & FT_TEMP_MASK;
+
+	for (i = 0; i < tmdev->chip->sensor_num; i++) {
+		int reg = (int)caldata[i + 1];
+		int sensor_temp = ths_reg2temp(tmdev, reg);
+		int delta, cdata, calib_offest;
+
+		/*
+		 * To calculate the calibration value:
+		 *
+		 * X(in Celsius) = Ts - ft_temp
+		 * delta = X * 10000 / TEMP_TO_REG
+		 * cdata = CALIBRATE_DEFAULT - delta
+		 *
+		 * cdata: calibration value
+		 */
+		delta = (sensor_temp - ft_temp * 100) * 10 / TEMP_TO_REG;
+		cdata = CALIBRATE_DEFAULT - delta;
+		if (cdata & ~TEMP_CALIB_MASK) {
+			/*
+			 * Calibration value more than 12-bit, but calibration
+			 * register is 12-bit. In this case, ths hardware can
+			 * still work without calibration, although the data
+			 * won't be so accurate.
+			 */
+			dev_warn(dev, "sensor%d is not calibrated.\n", i);
+
+			continue;
+		}
+
+		calib_offest = tmdev->chip->temp_calib_base + (i / 2) * 0x4;
+
+		if (i % 2) {
+			int val;
+
+			regmap_read(tmdev->regmap, calib_offest, &val);
+			val = (val & TEMP_CALIB_MASK) | (cdata << 16);
+			regmap_write(tmdev->regmap, calib_offest, val);
+		} else {
+			regmap_write(tmdev->regmap, calib_offest, cdata);
+		}
+	}
+
+out_free:
+	kfree(caldata);
+out:
+	return ret;
+}
+
+static int ths_register(struct ths_device *tmdev)
+{
+	struct thermal_zone_device *tzd;
+	int i = 0;
+
+	for (; i < tmdev->chip->sensor_num; i++) {
+		tmdev->sensor[i].tmdev = tmdev;
+		tmdev->sensor[i].id = i;
+		tmdev->sensor[i].tzd =
+			devm_thermal_zone_of_sensor_register(tmdev->dev,
+							     i,
+							     &tmdev->sensor[i],
+							     &ths_ops);
+		if (IS_ERR(tmdev->sensor[i].tzd))
+			return PTR_ERR(tzd);
+	}
+
+	return 0;
+}
+
+static int ths_probe(struct platform_device *pdev)
+{
+	struct ths_device *tmdev;
+	struct device *dev = &pdev->dev;
+	int ret;
+
+	tmdev = devm_kzalloc(dev, sizeof(*tmdev), GFP_KERNEL);
+	if (!tmdev)
+		return -ENOMEM;
+
+	tmdev->dev = dev;
+	tmdev->chip = of_device_get_match_data(&pdev->dev);
+	if (!tmdev->chip)
+		return -EINVAL;
+
+	ret = ths_init_resource(tmdev);
+	if (ret)
+		return ret;
+
+	ret = ths_register(tmdev);
+	if (ret)
+		return ret;
+
+	ret = tmdev->chip->enable(tmdev);
+	if (ret)
+		return ret;
+
+	platform_set_drvdata(pdev, tmdev);
+
+	return ret;
+}
+
+static int ths_remove(struct platform_device *pdev)
+{
+	struct ths_device *tmdev = platform_get_drvdata(pdev);
+
+	tmdev->chip->disable(tmdev);
+
+	return 0;
+}
+
+static int sun50i_thermal_enable(struct ths_device *tmdev)

drivers/thermal/sun8i_thermal.c line 350

Quoted 10 lines
drivers/thermal/sun8i_thermal.c new file +10 -0
+{
+	int ret, val;
+
+	ret = reset_control_deassert(tmdev->reset);
+	if (ret)
+		return ret;
+
+	ret = clk_prepare_enable(tmdev->bus_clk);
+	if (ret)
+		goto assert_reset;

What if we rename sun50i_thermal_enable to sun50i_thermal_setup and put clock setup and reset deassert to probe?

drivers/thermal/sun8i_thermal.c line 354

Quoted 3 lines
drivers/thermal/sun8i_thermal.c new file +3 -0
+	ret = ths_calibrate(tmdev);
+	if (ret)
+		goto assert_reset;

ths_calibrate will be SoC specific. On H3 for example, it would just be moving values from SID directly to some register. Maybe we can rename this to make this reflect that it's for H6 only, right now.

You also need to unprepare and disable the clock on failure.

Perhaps move this to struct ths_thermal_chip right away.

Quoted 10 lines
drivers/thermal/sun8i_thermal.c new file +10 -0
+	/*
+	 * clkin = 24MHz
+	 * T acquire = clkin / (x + 1)
+	 *           = 20us
+	 */
+	regmap_write(tmdev->regmap, SUN50I_THS_CTRL0,
+		     SUN50I_THS_CTRL0_T_ACQ(479));
+	/* average over 4 samples */
+	regmap_write(tmdev->regmap, SUN50I_H6_THS_MFC,
+		     SUN50I_THS_FILTER_EN |

drivers/thermal/sun8i_thermal.c line 375

Quoted 10 lines
drivers/thermal/sun8i_thermal.c new file +10 -0
+		     SUN50I_THS_FILTER_TYPE(1));
+	/* period = (x + 1) * 4096 / clkin; ~10ms */
+	regmap_write(tmdev->regmap, SUN50I_H6_THS_PC,
+		     SUN50I_H6_THS_PC_TEMP_PERIOD(58));
+	/* enable sensor */
+	val = GENMASK(tmdev->chip->sensor_num - 1, 0);
+	regmap_write(tmdev->regmap, SUN50I_H6_THS_ENABLE, val);
+	/* thermal data interrupt enable */
+	val = GENMASK(tmdev->chip->sensor_num - 1, 0);
+	regmap_write(tmdev->regmap, SUN50I_H6_THS_DIC, val);

It's probably better to clear the interrupt flags prior to enabling interrupts.

Quoted 5 lines
drivers/thermal/sun8i_thermal.c new file +5 -0
+	return 0;
+
+assert_reset:
+	reset_control_assert(tmdev->reset);
+

drivers/thermal/sun8i_thermal.c line 391

Quoted 10 lines
drivers/thermal/sun8i_thermal.c new file +10 -0
+	return ret;
+}
+
+static int sun50i_thermal_disable(struct ths_device *tmdev)
+{
+	clk_disable_unprepare(tmdev->bus_clk);
+	reset_control_assert(tmdev->reset);
+
+	return 0;
+}

I suggest moving this to ths_remove directly. And dropping sun50i_thermal_disable and ->disable callback completely.

thank you and regards,

	o.
Quoted 38 lines
drivers/thermal/sun8i_thermal.c new file +30 -0
+static const struct ths_thermal_chip sun50i_h6_ths = {
+	.sensor_num = 2,
+	.offset = -2794,
+	.scale = -67,
+	.ft_deviation = SUN50I_H6_FT_DEVIATION,
+	.temp_calib_base = SUN50I_H6_THS_TEMP_CALIB,
+	.temp_data_base = SUN50I_H6_THS_TEMP_DATA,
+	.enable = sun50i_thermal_enable,
+	.disable = sun50i_thermal_disable,
+	.irq_thread = sun50i_h6_irq_thread,
+};
+
+static const struct of_device_id of_ths_match[] = {
+	{ .compatible = "allwinner,sun50i-h6-ths", .data = &sun50i_h6_ths },
+	{ /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, of_ths_match);
+
+static struct platform_driver ths_driver = {
+	.probe = ths_probe,
+	.remove = ths_remove,
+	.driver = {
+		.name = "sun8i-thermal",
+		.of_match_table = of_ths_match,
+	},
+};
+module_platform_driver(ths_driver);
+
+MODULE_DESCRIPTION("Thermal sensor driver for Allwinner SOC");
+MODULE_LICENSE("GPL v2");
Signature · 7 lines
2.17.0


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#4 lore raw
In reply to Yangtao Li

Hi,

Quoted 1 line · Yangtao Li

This patchset supprt H6 thermal controller.

The discussion is still ongoing on the v1, it would have been better to wait a bit on it to settle before sending a new version.

Anyway, some comment made there still apply.

Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com