Skip to contentSkip to conversation

gfs2: Fix lru_count going negative

PATCH New Sasha Levin 1 participant 32 messages May 22, 2019

Subsystems (13)
lore
Share & tools
lore

Sasha Levin

author maintainer
#0 lore raw

PATCH 1/92 gfs2: Fix lru_count going negative

From: Ross Lagerwall <[email protected]>

[ Upstream commit 7881ef3f33bb80f459ea6020d1e021fc524a6348 ]

Under certain conditions, lru_count may drop below zero resulting in a large amount of log spam like this:

vmscan: shrink_slab: gfs2_dump_glock+0x3b0/0x630 [gfs2] \
negative objects to delete nr=-1

This happens as follows:
1) A glock is moved from lru_list to the dispose list and lru_count is decremented.
2) The dispose function calls cond_resched() and drops the lru lock.
3) Another thread takes the lru lock and tries to add the same glock to lru_list, checking if the glock is on an lru list.
4) It is on a list (actually the dispose list) and so it avoids incrementing lru_count.
5) The glock is moved to lru_list.
5) The original thread doesn't dispose it because it has been re-added to the lru list but the lru_count has still decreased by one.

Fix by checking if the LRU flag is set on the glock rather than checking if the glock is on some list and rearrange the code so that the LRU flag is added/removed precisely when the glock is added/removed from lru_list.

---
 fs/gfs2/glock.c | 22 +++++++++++++---------
 1 file changed, 13 insertions(+), 9 deletions(-)
fs/gfs2/glock.c +13 -9
index 09a0cf5f3dd86..1eb737c466ddc 100644
@@ -136,22 +136,26 @@ static int demote_ok(const struct gfs2_glock *gl)
 
 void gfs2_glock_add_to_lru(struct gfs2_glock *gl)
 {
+	if (!(gl->gl_ops->go_flags & GLOF_LRU))
+		return;
+
 	spin_lock(&lru_lock);
 
-	if (!list_empty(&gl->gl_lru))
-		list_del_init(&gl->gl_lru);
-	else
+	list_del(&gl->gl_lru);
+	list_add_tail(&gl->gl_lru, &lru_list);
+
+	if (!test_bit(GLF_LRU, &gl->gl_flags)) {
+		set_bit(GLF_LRU, &gl->gl_flags);
 		atomic_inc(&lru_count);
+	}
 
-	list_add_tail(&gl->gl_lru, &lru_list);
-	set_bit(GLF_LRU, &gl->gl_flags);
 	spin_unlock(&lru_lock);
 }
 
 static void gfs2_glock_remove_from_lru(struct gfs2_glock *gl)
 {
 	spin_lock(&lru_lock);
-	if (!list_empty(&gl->gl_lru)) {
+	if (test_bit(GLF_LRU, &gl->gl_flags)) {
 		list_del_init(&gl->gl_lru);
 		atomic_dec(&lru_count);
 		clear_bit(GLF_LRU, &gl->gl_flags);
@@ -1040,8 +1044,7 @@ void gfs2_glock_dq(struct gfs2_holder *gh)
 		    !test_bit(GLF_DEMOTE, &gl->gl_flags))
 			fast_path = 1;
 	}
-	if (!test_bit(GLF_LFLUSH, &gl->gl_flags) && demote_ok(gl) &&
-	    (glops->go_flags & GLOF_LRU))
+	if (!test_bit(GLF_LFLUSH, &gl->gl_flags) && demote_ok(gl))
 		gfs2_glock_add_to_lru(gl);
 
 	trace_gfs2_glock_queue(gh, 0);
@@ -1341,6 +1344,7 @@ __acquires(&lru_lock)
 		if (!spin_trylock(&gl->gl_lockref.lock)) {
 add_back_to_lru:
 			list_add(&gl->gl_lru, &lru_list);
+			set_bit(GLF_LRU, &gl->gl_flags);
 			atomic_inc(&lru_count);
 			continue;
 		}
@@ -1348,7 +1352,6 @@ __acquires(&lru_lock)
 			spin_unlock(&gl->gl_lockref.lock);
 			goto add_back_to_lru;
 		}
-		clear_bit(GLF_LRU, &gl->gl_flags);
 		gl->gl_lockref.count++;
 		if (demote_ok(gl))
 			handle_callback(gl, LM_ST_UNLOCKED, 0, false);
@@ -1384,6 +1387,7 @@ static long gfs2_scan_glock_lru(int nr)
 		if (!test_bit(GLF_LOCK, &gl->gl_flags)) {
 			list_move(&gl->gl_lru, &dispose);
 			atomic_dec(&lru_count);
+			clear_bit(GLF_LRU, &gl->gl_flags);
 			freed++;
 			continue;
 		}
Signature · 1 line
2.20.1
author maintainer
#2 lore raw

PATCH 3/92 mmc: core: Verify SD bus width

From: Raul E Rangel <[email protected]>

[ Upstream commit 9e4be8d03f50d1b25c38e2b59e73b194c130df7d ]

The SD Physical Layer Spec says the following: Since the SD Memory Card shall support at least the two bus modes 1-bit or 4-bit width, then any SD Card shall set at least bits 0 and 2 (SD_BUS_WIDTH="0101").

This change verifies the card has specified a bus width.

AMD SDHC Device 7806 can get into a bad state after a card disconnect where anything transferred via the DATA lines will always result in a zero filled buffer. Currently the driver will continue without error if the HC is in this condition. A block device will be created, but reading from it will result in a zero buffer. This makes it seem like the SD device has been erased, when in actuality the data is never getting copied from the DATA lines to the data buffer.

SCR is the first command in the SD initialization sequence that uses the DATA lines. By checking that the response was invalid, we can abort mounting the card.

---
 drivers/mmc/core/sd.c | 8 ++++++++
 1 file changed, 8 insertions(+)
drivers/mmc/core/sd.c +8 -0
index 967535d76e346..fb8741f18c1f5 100644
@@ -216,6 +216,14 @@ static int mmc_decode_scr(struct mmc_card *card)
 
 	if (scr->sda_spec3)
 		scr->cmds = UNSTUFF_BITS(resp, 32, 2);
+
+	/* SD Spec says: any SD Card shall set at least bits 0 and 2 */
+	if (!(scr->bus_widths & SD_SCR_BUS_WIDTH_1) ||
+	    !(scr->bus_widths & SD_SCR_BUS_WIDTH_4)) {
+		pr_err("%s: invalid bus width\n", mmc_hostname(card->host));
+		return -EINVAL;
+	}
+
 	return 0;
 }
 
Signature · 1 line
2.20.1
author maintainer
#5 lore raw

PATCH 6/92 spi: pxa2xx: fix SCR (divisor) calculation

In reply to Sasha Levin

From: Flavio Suligoi <[email protected]>

[ Upstream commit 29f2133717c527f492933b0622a4aafe0b3cbe9e ]

Calculate the divisor for the SCR (Serial Clock Rate), avoiding that the SSP transmission rate can be greater than the device rate.

When the division between the SSP clock and the device rate generates a reminder, we have to increment by one the divisor.
In this way the resulting SSP clock will never be greater than the device SPI max frequency.

For example, with:

- ssp_clk = 50 MHz
- dev freq = 15 MHz

without this patch the SSP clock will be greater than 15 MHz:

- 25 MHz for PXA25x_SSP and CE4100_SSP
- 16,56 MHz for the others

Instead, with this patch, we have in both case an SSP clock of 12.5MHz, so the max rate of the SPI device clock is respected.

---
 drivers/spi/spi-pxa2xx.c | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)
drivers/spi/spi-pxa2xx.c +6 -2
index 3cac73e4c3e4a..e87b6fc9f4c63 100644
@@ -859,10 +859,14 @@ static unsigned int ssp_get_clk_div(struct driver_data *drv_data, int rate)
 
 	rate = min_t(int, ssp_clk, rate);
 
+	/*
+	 * Calculate the divisor for the SCR (Serial Clock Rate), avoiding
+	 * that the SSP transmission rate can be greater than the device rate
+	 */
 	if (ssp->type == PXA25x_SSP || ssp->type == CE4100_SSP)
-		return (ssp_clk / (2 * rate) - 1) & 0xff;
+		return (DIV_ROUND_UP(ssp_clk, 2 * rate) - 1) & 0xff;
 	else
-		return (ssp_clk / rate - 1) & 0xfff;
+		return (DIV_ROUND_UP(ssp_clk, rate) - 1)  & 0xfff;
 }
 
 static unsigned int pxa2xx_ssp_get_clk_div(struct driver_data *drv_data,
Signature · 1 line
2.20.1
author maintainer
#17 lore raw

PATCH 18/92 bcache: return error immediately in bch_journal_replay()

In reply to Sasha Levin

From: Coly Li <[email protected]>

[ Upstream commit 68d10e6979a3b59e3cd2e90bfcafed79c4cf180a ]

When failure happens inside bch_journal_replay(), calling cache_set_err_on() and handling the failure in async way is not a good idea. Because after bch_journal_replay() returns, registering code will continue to execute following steps, and unregistering code triggered by cache_set_err_on() is running in same time. First it is unnecessary to handle failure and unregister cache set in an async way, second there might be potential race condition to run register and unregister code for same cache set.

So in this patch, if failure happens in bch_journal_replay(), we don't call cache_set_err_on(), and just print out the same error message to kernel message buffer, then return -EIO immediately caller. Then caller can detect such failure and handle it in synchrnozied way.

---
 drivers/md/bcache/journal.c | 9 ++++++---
 1 file changed, 6 insertions(+), 3 deletions(-)
drivers/md/bcache/journal.c +6 -3
index 6ed066a0e7c0a..dfedc2c1f1e15 100644
@@ -322,9 +322,12 @@ int bch_journal_replay(struct cache_set *s, struct list_head *list)
 	list_for_each_entry(i, list, list) {
 		BUG_ON(i->pin && atomic_read(i->pin) != 1);
 
-		cache_set_err_on(n != i->j.seq, s,
-"bcache: journal entries %llu-%llu missing! (replaying %llu-%llu)",
-				 n, i->j.seq - 1, start, end);
+		if (n != i->j.seq) {
+			pr_err("bcache: journal entries %llu-%llu missing! (replaying %llu-%llu)",
+			n, i->j.seq - 1, start, end);
+			ret = -EIO;
+			goto err;
+		}
 
 		for (k = i->j.start;
 		     k < bset_bkey_last(&i->j);
Signature · 1 line
2.20.1
author maintainer
#18 lore raw

PATCH 19/92 bcache: fix failure in journal relplay

In reply to Sasha Levin

From: Tang Junhui <[email protected]>

[ Upstream commit 631207314d88e9091be02fbdd1fdadb1ae2ed79a ]

journal replay failed with messages:

Sep 10 19:10:43 ceph kernel: bcache: error on

bb379a64-e44e-4812-b91d-a5599871a3b1: bcache: journal entries 2057493-2057567 missing! (replaying 2057493-2076601), disabling caching

The reason is in journal_reclaim(), when discard is enabled, we send discard command and reclaim those journal buckets whose seq is old than the last_seq_now, but before we write a journal with last_seq_now, the machine is restarted, so the journal with the last_seq_now is not written to the journal bucket, and the last_seq_wrote in the newest journal is old than last_seq_now which we expect to be, so when we doing replay, journals from last_seq_wrote to last_seq_now are missing.

It's hard to write a journal immediately after journal_reclaim(), and it harmless if those missed journal are caused by discarding since those journals are already wrote to btree node. So, if miss seqs are started from the beginning journal, we treat it as normal, and only print a message to show the miss journal, and point out it maybe caused by discarding.

Patch v2 add a judgement condition to ignore the missed journal only when discard enabled as Coly suggested.

(Coly Li: rebase the patch with other changes in bch_journal_replay())

---
 drivers/md/bcache/journal.c | 25 +++++++++++++++++++++----
 1 file changed, 21 insertions(+), 4 deletions(-)
drivers/md/bcache/journal.c +21 -4
index dfedc2c1f1e15..e12907fef597c 100644
@@ -309,6 +309,18 @@ void bch_journal_mark(struct cache_set *c, struct list_head *list)
 	}
 }
 
+bool is_discard_enabled(struct cache_set *s)
+{
+	struct cache *ca;
+	unsigned int i;
+
+	for_each_cache(ca, s, i)
+		if (ca->discard)
+			return true;
+
+	return false;
+}
+
 int bch_journal_replay(struct cache_set *s, struct list_head *list)
 {
 	int ret = 0, keys = 0, entries = 0;
@@ -323,10 +335,15 @@ int bch_journal_replay(struct cache_set *s, struct list_head *list)
 		BUG_ON(i->pin && atomic_read(i->pin) != 1);
 
 		if (n != i->j.seq) {
-			pr_err("bcache: journal entries %llu-%llu missing! (replaying %llu-%llu)",
-			n, i->j.seq - 1, start, end);
-			ret = -EIO;
-			goto err;
+			if (n == start && is_discard_enabled(s))
+				pr_info("bcache: journal entries %llu-%llu may be discarded! (replaying %llu-%llu)",
+					n, i->j.seq - 1, start, end);
+			else {
+				pr_err("bcache: journal entries %llu-%llu missing! (replaying %llu-%llu)",
+					n, i->j.seq - 1, start, end);
+				ret = -EIO;
+				goto err;
+			}
 		}
 
 		for (k = i->j.start;
Signature · 1 line
2.20.1
author maintainer
#19 lore raw

PATCH 20/92 bcache: add failure check to run_cache_set() for journal replay

In reply to Sasha Levin

From: Coly Li <[email protected]>

[ Upstream commit ce3e4cfb59cb382f8e5ce359238aa580d4ae7778 ]

Currently run_cache_set() has no return value, if there is failure in bch_journal_replay(), the caller of run_cache_set() has no idea about such failure and just continue to execute following code after run_cache_set(). The internal failure is triggered inside bch_journal_replay() and being handled in async way. This behavior is inefficient, while failure handling inside bch_journal_replay(), cache register code is still running to start the cache set. Registering and unregistering code running as same time may introduce some rare race condition, and make the code to be more hard to be understood.

This patch adds return value to run_cache_set(), and returns -EIO if bch_journal_rreplay() fails. Then caller of run_cache_set() may detect such failure and stop registering code flow immedidately inside register_cache_set().

If journal replay fails, run_cache_set() can report error immediately to register_cache_set(). This patch makes the failure handling for bch_journal_replay() be in synchronized way, easier to understand and debug, and avoid poetential race condition for register-and-unregister in same time.

---
 drivers/md/bcache/super.c | 17 ++++++++++++-----
 1 file changed, 12 insertions(+), 5 deletions(-)
drivers/md/bcache/super.c +12 -5
index ef28ddfff7c61..420877cabd2fc 100644
@@ -1558,7 +1558,7 @@ struct cache_set *bch_cache_set_alloc(struct cache_sb *sb)
 	return NULL;
 }
 
-static void run_cache_set(struct cache_set *c)
+static int run_cache_set(struct cache_set *c)
 {
 	const char *err = "cannot allocate memory";
 	struct cached_dev *dc, *t;
@@ -1650,7 +1650,9 @@ static void run_cache_set(struct cache_set *c)
 		if (j->version < BCACHE_JSET_VERSION_UUID)
 			__uuid_write(c);
 
-		bch_journal_replay(c, &journal);
+		err = "bcache: replay journal failed";
+		if (bch_journal_replay(c, &journal))
+			goto err;
 	} else {
 		pr_notice("invalidating existing data");
 
@@ -1718,11 +1720,13 @@ static void run_cache_set(struct cache_set *c)
 	flash_devs_run(c);
 
 	set_bit(CACHE_SET_RUNNING, &c->flags);
-	return;
+	return 0;
 err:
 	closure_sync(&cl);
 	/* XXX: test this, it's broken */
 	bch_cache_set_error(c, "%s", err);
+
+	return -EIO;
 }
 
 static bool can_attach_cache(struct cache *ca, struct cache_set *c)
@@ -1786,8 +1790,11 @@ static const char *register_cache_set(struct cache *ca)
 	ca->set->cache[ca->sb.nr_this_dev] = ca;
 	c->cache_by_alloc[c->caches_loaded++] = ca;
 
-	if (c->caches_loaded == c->sb.nr_in_set)
-		run_cache_set(c);
+	if (c->caches_loaded == c->sb.nr_in_set) {
+		err = "failed to run cache set";
+		if (run_cache_set(c) < 0)
+			goto err;
+	}
 
 	return NULL;
 err:
Signature · 1 line
2.20.1
author maintainer
#20 lore raw

PATCH 21/92 bcache: avoid clang -Wunintialized warning

In reply to Sasha Levin

From: Arnd Bergmann <[email protected]>

[ Upstream commit 78d4eb8ad9e1d413449d1b7a060f50b6efa81ebd ]

clang has identified a code path in which it thinks a variable may be unused:

drivers/md/bcache/alloc.c:333:4: error: variable 'bucket' is used uninitialized whenever 'if' condition is false

      [-Werror,-Wsometimes-uninitialized]
                        fifo_pop(&ca->free_inc, bucket);
                        ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/md/bcache/util.h:219:27: note: expanded from macro 'fifo_pop'
 #define fifo_pop(fifo, i)       fifo_pop_front(fifo, (i))
                                ^~~~~~~~~~~~~~~~~~~~~~~~~
drivers/md/bcache/util.h:189:6: note: expanded from macro 'fifo_pop_front'
        if (_r) {                                                       \
            ^~
drivers/md/bcache/alloc.c:343:46: note: uninitialized use occurs here
                        allocator_wait(ca, bch_allocator_push(ca, bucket));
                                                                  ^~~~~~
drivers/md/bcache/alloc.c:287:7: note: expanded from macro 'allocator_wait'
                if (cond)                                               \
                    ^~~~
drivers/md/bcache/alloc.c:333:4: note: remove the 'if' if its condition is always true
                        fifo_pop(&ca->free_inc, bucket);
                        ^
drivers/md/bcache/util.h:219:27: note: expanded from macro 'fifo_pop'
 #define fifo_pop(fifo, i)       fifo_pop_front(fifo, (i))
                                ^
drivers/md/bcache/util.h:189:2: note: expanded from macro 'fifo_pop_front'
        if (_r) {                                                       \
        ^
drivers/md/bcache/alloc.c:331:15: note: initialize the variable 'bucket' to silence this warning
                        long bucket;
                                   ^

This cannot happen in practice because we only enter the loop if there is at least one element in the list.

Slightly rearranging the code makes this clearer to both the reader and the compiler, which avoids the warning.

---
 drivers/md/bcache/alloc.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)
drivers/md/bcache/alloc.c +3 -2
index 16c3390e5d9f3..d82ae445c9ee3 100644
@@ -324,10 +324,11 @@ static int bch_allocator_thread(void *arg)
 		 * possibly issue discards to them, then we add the bucket to
 		 * the free list:
 		 */
-		while (!fifo_empty(&ca->free_inc)) {
+		while (1) {
 			long bucket;
 
-			fifo_pop(&ca->free_inc, bucket);
+			if (!fifo_pop(&ca->free_inc, bucket))
+				break;
 
 			if (ca->discard) {
 				mutex_unlock(&ca->set->bucket_lock);
Signature · 1 line
2.20.1
author maintainer
#21 lore raw

PATCH 22/92 RDMA/cma: Consider scope_id while binding to ipv6 ll address

In reply to Sasha Levin

From: Parav Pandit <[email protected]>

[ Upstream commit 5d7ed2f27bbd482fd29e6b2e204b1a1ee8a0b268 ]

When two netdev have same link local addresses (such as vlan and non vlan), two rdma cm listen id should be able to bind to following different addresses.

listener-1: addr=lla, scope_id=A, port=X
listener-2: addr=lla, scope_id=B, port=X

However while comparing the addresses only addr and port are considered, due to which 2nd listener fails to listen.

In below example of two listeners, 2nd listener is failing with address in use error.

$ rping -sv -a fe80::268a:7ff:feb3:d113%ens2f1 -p 4545&
$ rping -sv -a fe80::268a:7ff:feb3:d113%ens2f1.200 -p 4545
rdma_bind_addr: Address already in use

To overcome this, consider the scope_ids as well which forms the accurate IPv6 link local address.

---
 drivers/infiniband/core/cma.c | 25 +++++++++++++++++++------
 1 file changed, 19 insertions(+), 6 deletions(-)
drivers/infiniband/core/cma.c +19 -6
index 1454290078def..76e7eca35a110 100644
@@ -902,18 +902,31 @@ static inline int cma_any_addr(struct sockaddr *addr)
 	return cma_zero_addr(addr) || cma_loopback_addr(addr);
 }
 
-static int cma_addr_cmp(struct sockaddr *src, struct sockaddr *dst)
+static int cma_addr_cmp(const struct sockaddr *src, const struct sockaddr *dst)
 {
 	if (src->sa_family != dst->sa_family)
 		return -1;
 
 	switch (src->sa_family) {
 	case AF_INET:
-		return ((struct sockaddr_in *) src)->sin_addr.s_addr !=
-		       ((struct sockaddr_in *) dst)->sin_addr.s_addr;
-	case AF_INET6:
-		return ipv6_addr_cmp(&((struct sockaddr_in6 *) src)->sin6_addr,
-				     &((struct sockaddr_in6 *) dst)->sin6_addr);
+		return ((struct sockaddr_in *)src)->sin_addr.s_addr !=
+		       ((struct sockaddr_in *)dst)->sin_addr.s_addr;
+	case AF_INET6: {
+		struct sockaddr_in6 *src_addr6 = (struct sockaddr_in6 *)src;
+		struct sockaddr_in6 *dst_addr6 = (struct sockaddr_in6 *)dst;
+		bool link_local;
+
+		if (ipv6_addr_cmp(&src_addr6->sin6_addr,
+					  &dst_addr6->sin6_addr))
+			return 1;
+		link_local = ipv6_addr_type(&dst_addr6->sin6_addr) &
+			     IPV6_ADDR_LINKLOCAL;
+		/* Link local must match their scope_ids */
+		return link_local ? (src_addr6->sin6_scope_id !=
+				     dst_addr6->sin6_scope_id) :
+				    0;
+	}
+
 	default:
 		return ib_addr_cmp(&((struct sockaddr_ib *) src)->sib_addr,
 				   &((struct sockaddr_ib *) dst)->sib_addr);
Signature · 1 line
2.20.1
author maintainer
#26 lore raw

PATCH 27/92 HID: logitech-hidpp: use RAP instead of FAP to get the protocol version

In reply to Sasha Levin

From: Hans de Goede <[email protected]>

[ Upstream commit 096377525cdb8251e4656085efc988bdf733fb4c ]

According to the logitech_hidpp_2.0_specification_draft_2012-06-04.pdf doc:
https://lekensteyn.nl/files/logitech/logitech_hidpp_2.0_specification_draft_2012-06-04.pdf

We should use a register-access-protocol request using the short input / output report ids. This is necessary because 27MHz HID++ receivers have a max-packetsize on their HIP++ endpoint of 8, so they cannot support long reports. Using a feature-access-protocol request (which is always long or very-long) with these will cause a timeout error, followed by the hidpp driver treating the device as not being HID++ capable.

This commit fixes this by switching to using a rap request to get the protocol version.

Besides being tested with a (046d:c517) 27MHz receiver with various 27MHz keyboards and mice, this has also been tested to not cause regressions on a non-unifying dual-HID++ nano receiver (046d:c534) with k270 and m185 HID++-2.0 devices connected and on a unifying/dj receiver (046d:c52b) with a HID++-2.0 Logitech Rechargeable Touchpad T650.

---
 drivers/hid/hid-logitech-hidpp.c | 17 +++++++++++++----
 1 file changed, 13 insertions(+), 4 deletions(-)
drivers/hid/hid-logitech-hidpp.c +13 -4
index 5fd97860aec4d..3666e5064d0d3 100644
@@ -414,13 +414,16 @@ static int hidpp_root_get_feature(struct hidpp_device *hidpp, u16 feature,
 
 static int hidpp_root_get_protocol_version(struct hidpp_device *hidpp)
 {
+	const u8 ping_byte = 0x5a;
+	u8 ping_data[3] = { 0, 0, ping_byte };
 	struct hidpp_report response;
 	int ret;
 
-	ret = hidpp_send_fap_command_sync(hidpp,
+	ret = hidpp_send_rap_command_sync(hidpp,
+			REPORT_ID_HIDPP_SHORT,
 			HIDPP_PAGE_ROOT_IDX,
 			CMD_ROOT_GET_PROTOCOL_VERSION,
-			NULL, 0, &response);
+			ping_data, sizeof(ping_data), &response);
 
 	if (ret == HIDPP_ERROR_INVALID_SUBID) {
 		hidpp->protocol_major = 1;
@@ -440,8 +443,14 @@ static int hidpp_root_get_protocol_version(struct hidpp_device *hidpp)
 	if (ret)
 		return ret;
 
-	hidpp->protocol_major = response.fap.params[0];
-	hidpp->protocol_minor = response.fap.params[1];
+	if (response.rap.params[2] != ping_byte) {
+		hid_err(hidpp->hid_dev, "%s: ping mismatch 0x%02x != 0x%02x\n",
+			__func__, response.rap.params[2], ping_byte);
+		return -EPROTO;
+	}
+
+	hidpp->protocol_major = response.rap.params[0];
+	hidpp->protocol_minor = response.rap.params[1];
 
 	return ret;
 }
Signature · 1 line
2.20.1
author maintainer
#27 lore raw

PATCH 28/92 pinctrl: pistachio: fix leaked of_node references

In reply to Sasha Levin

From: Wen Yang <[email protected]>

[ Upstream commit 44a4455ac2c6b0981eace683a2b6eccf47689022 ]

The call to of_get_child_by_name returns a node pointer with refcount incremented thus it must be explicitly decremented after the last usage.

Detected by coccinelle with the following warnings:
./drivers/pinctrl/pinctrl-pistachio.c:1422:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1360, but without a corresponding object release within this function.

---
 drivers/pinctrl/pinctrl-pistachio.c | 2 ++
 1 file changed, 2 insertions(+)
drivers/pinctrl/pinctrl-pistachio.c +2 -0
index 98a459b1c095a..86e8d989092c8 100644
@@ -1373,6 +1373,7 @@ static int pistachio_gpio_register(struct pistachio_pinctrl *pctl)
 		if (!of_find_property(child, "gpio-controller", NULL)) {
 			dev_err(pctl->dev,
 				"No gpio-controller property for bank %u\n", i);
+			of_node_put(child);
 			ret = -ENODEV;
 			goto err;
 		}
@@ -1380,6 +1381,7 @@ static int pistachio_gpio_register(struct pistachio_pinctrl *pctl)
 		irq = irq_of_parse_and_map(child, 0);
 		if (irq < 0) {
 			dev_err(pctl->dev, "No IRQ for bank %u: %d\n", i, irq);
+			of_node_put(child);
 			ret = irq;
 			goto err;
 		}
Signature · 1 line
2.20.1
author maintainer
#3 lore raw

PATCH 4/92 powerpc/boot: Fix missing check of lseek() return value

In reply to Sasha Levin

From: Bo YU <[email protected]>

[ Upstream commit 5d085ec04a000fefb5182d3b03ee46ca96d8389b ]

This is detected by Coverity scan: CID: 1440481

---
 arch/powerpc/boot/addnote.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)
arch/powerpc/boot/addnote.c +5 -1
index 9d9f6f334d3cc..3da3e2b1b51bc 100644
@@ -223,7 +223,11 @@ main(int ac, char **av)
 	PUT_16(E_PHNUM, np + 2);
 
 	/* write back */
-	lseek(fd, (long) 0, SEEK_SET);
+	i = lseek(fd, (long) 0, SEEK_SET);
+	if (i < 0) {
+		perror("lseek");
+		exit(1);
+	}
 	i = write(fd, buf, n);
 	if (i < 0) {
 		perror("write");
Signature · 1 line
2.20.1
author maintainer
#6 lore raw

PATCH 7/92 brcm80211: potential NULL dereference in brcmf_cfg80211_vndr_cmds_dcmd_handler()

In reply to Sasha Levin

From: Dan Carpenter <[email protected]>

[ Upstream commit e025da3d7aa4770bb1d1b3b0aa7cc4da1744852d ]

If "ret_len" is negative then it could lead to a NULL dereference.

The "ret_len" value comes from nl80211_vendor_cmd(), if it's negative then we don't allocate the "dcmd_buf" buffer. Then we pass "ret_len" to brcmf_fil_cmd_data_set() where it is cast to a very high u32 value. Most of the functions in that call tree check whether the buffer we pass is NULL but there are at least a couple places which don't such as brcmf_dbg_hex_dump() and brcmf_msgbuf_query_dcmd(). We memcpy() to and from the buffer so it would result in a NULL dereference.

The fix is to change the types so that "ret_len" can't be negative. (If we memcpy() zero bytes to NULL, that's a no-op and doesn't cause an issue).

Fixes 1bacb0487d0e ("brcmfmac: replace cfg80211 testmode with vendor command")
---
 drivers/net/wireless/brcm80211/brcmfmac/vendor.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)
drivers/net/wireless/brcm80211/brcmfmac/vendor.c +3 -2
index 8eff2753abade..d493021f60318 100644
@@ -35,9 +35,10 @@ static int brcmf_cfg80211_vndr_cmds_dcmd_handler(struct wiphy *wiphy,
 	struct brcmf_if *ifp;
 	const struct brcmf_vndr_dcmd_hdr *cmdhdr = data;
 	struct sk_buff *reply;
-	int ret, payload, ret_len;
+	unsigned int payload, ret_len;
 	void *dcmd_buf = NULL, *wr_pointer;
 	u16 msglen, maxmsglen = PAGE_SIZE - 0x100;
+	int ret;
 
 	if (len < sizeof(*cmdhdr)) {
 		brcmf_err("vendor command too short: %d\n", len);
@@ -65,7 +66,7 @@ static int brcmf_cfg80211_vndr_cmds_dcmd_handler(struct wiphy *wiphy,
 			brcmf_err("oversize return buffer %d\n", ret_len);
 			ret_len = BRCMF_DCMD_MAXLEN;
 		}
-		payload = max(ret_len, len) + 1;
+		payload = max_t(unsigned int, ret_len, len) + 1;
 		dcmd_buf = vzalloc(payload);
 		if (NULL == dcmd_buf)
 			return -ENOMEM;
Signature · 1 line
2.20.1
author maintainer
#8 lore raw

PATCH 9/92 w1: fix the resume command API

In reply to Sasha Levin

From: Mariusz Bialonczyk <[email protected]>

[ Upstream commit 62909da8aca048ecf9fbd7e484e5100608f40a63 ]

Quoted 1 line

From the DS2408 datasheet [1]:

"Resume Command function checks the status of the RC flag and, if it is set,
directly transfers control to the control functions, similar to a Skip ROM command. The only way to set the RC flag is through successfully executing the Match ROM, Search ROM, Conditional Search ROM, or Overdrive-Match ROM command"

The function currently works perfectly fine in a multidrop bus, but when we have only a single slave connected, then only a Skip ROM is used and Match ROM is not called at all. This is leading to problems e.g. with single one DS2408 connected, as the Resume Command is not working properly and the device is responding with failing results after the Resume Command.

This commit is fixing this by using a Skip ROM instead in those cases. The bandwidth / performance advantage is exactly the same.

Refs:
[1] https://datasheets.maximintegrated.com/en/ds/DS2408.pdf

---
 drivers/w1/w1_io.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)
drivers/w1/w1_io.c +1 -2
index 282092421cc9e..1a9d9ec8db4df 100644
@@ -437,8 +437,7 @@ int w1_reset_resume_command(struct w1_master *dev)
 	if (w1_reset_bus(dev))
 		return -1;
 
-	/* This will make only the last matched slave perform a skip ROM. */
-	w1_write_8(dev, W1_RESUME_CMD);
+	w1_write_8(dev, dev->slave_count > 1 ? W1_RESUME_CMD : W1_SKIP_ROM);
 	return 0;
 }
 EXPORT_SYMBOL_GPL(w1_reset_resume_command);
Signature · 1 line
2.20.1
author maintainer
#10 lore raw

PATCH 11/92 mac80211/cfg80211: update bss channel on channel switch

In reply to Sasha Levin

From: Sergey Matyukevich <[email protected]>

[ Upstream commit 5dc8cdce1d722c733f8c7af14c5fb595cfedbfa8 ]

FullMAC STAs have no way to update bss channel after CSA channel switch completion. As a result, user-space tools may provide inconsistent channel info. For instance, consider the following two commands:

$ sudo iw dev wlan0 link
$ sudo iw dev wlan0 info
The latter command gets channel info from the hardware, so most probably
its output will be correct. However the former command gets channel info
from scan cache, so its output will contain outdated channel info.
In fact, current bss channel info will not be updated until the
next [re-]connect.

Note that mac80211 STAs have a workaround for this, but it requires access to internal cfg80211 data, see ieee80211_chswitch_work:

	/* XXX: shouldn't really modify cfg80211-owned data! */
	ifmgd->associated->channel = sdata->csa_chandef.chan;

This patch suggests to convert mac80211 workaround into cfg80211 behavior and to update current bss channel in cfg80211_ch_switch_notify.

---
 net/mac80211/mlme.c    | 3 ---
 net/wireless/nl80211.c | 5 +++++
 2 files changed, 5 insertions(+), 3 deletions(-)
net/mac80211/mlme.c +0 -3
index ed4fef32b394f..08384dbf426c8 100644
@@ -1104,9 +1104,6 @@ static void ieee80211_chswitch_work(struct work_struct *work)
 		goto out;
 	}
 
-	/* XXX: shouldn't really modify cfg80211-owned data! */
-	ifmgd->associated->channel = sdata->csa_chandef.chan;
-
 	ifmgd->csa_waiting_bcn = true;
 
 	ieee80211_sta_reset_beacon_monitor(sdata);
net/wireless/nl80211.c +5 -0
index 81013490a99f4..1968998e6c6c2 100644
@@ -12788,6 +12788,11 @@ void cfg80211_ch_switch_notify(struct net_device *dev,
 
 	wdev->chandef = *chandef;
 	wdev->preset_chandef = *chandef;
+
+	if (wdev->iftype == NL80211_IFTYPE_STATION &&
+	    !WARN_ON(!wdev->current_bss))
+		wdev->current_bss->pub.channel = chandef->chan;
+
 	nl80211_ch_switch_notify(rdev, dev, chandef, GFP_KERNEL,
 				 NL80211_CMD_CH_SWITCH_NOTIFY, 0);
 }
Signature · 1 line
2.20.1
author maintainer
#13 lore raw

PATCH 14/92 mwifiex: prevent an array overflow

In reply to Sasha Levin

From: Dan Carpenter <[email protected]>

[ Upstream commit b4c35c17227fe437ded17ce683a6927845f8c4a4 ]

The "rate_index" is only used as an index into the phist_data->rx_rate[] array in the mwifiex_hist_data_set() function. That array has MWIFIEX_MAX_AC_RX_RATES (74) elements and it's used to generate some debugfs information. The "rate_index" variable comes from the network skb->data[] and it is a u8 so it's in the 0-255 range. We need to cap it to prevent an array overflow.

Fixes cbf6e05527a7 ("mwifiex: add rx histogram statistics support")
---
 drivers/net/wireless/mwifiex/cfp.c | 3 +++
 1 file changed, 3 insertions(+)
drivers/net/wireless/mwifiex/cfp.c +3 -0
index 3ddb8ec676ed3..6dd331dfb5179 100644
@@ -533,5 +533,8 @@ u8 mwifiex_adjust_data_rate(struct mwifiex_private *priv,
 		rate_index = (rx_rate > MWIFIEX_RATE_INDEX_OFDM0) ?
 			      rx_rate - 1 : rx_rate;
 
+	if (rate_index >= MWIFIEX_MAX_AC_RX_RATES)
+		rate_index = MWIFIEX_MAX_AC_RX_RATES - 1;
+
 	return rate_index;
 }
Signature · 1 line
2.20.1
author maintainer
#12 lore raw

PATCH 13/92 ASoC: fsl_sai: Update is_slave_mode with correct value

In reply to Sasha Levin

From: Daniel Baluta <[email protected]>

[ Upstream commit ddb351145a967ee791a0fb0156852ec2fcb746ba ]

is_slave_mode defaults to false because sai structure that contains it is kzalloc'ed.

Anyhow, if we decide to set the following configuration SAI slave -> SAI master, is_slave_mode will remain set on true although SAI being master it should be set to false.

Fix this by updating is_slave_mode for each call of fsl_sai_set_dai_fmt.

---
 sound/soc/fsl/fsl_sai.c | 2 ++
 1 file changed, 2 insertions(+)
sound/soc/fsl/fsl_sai.c +2 -0
index 08b460ba06efc..61d2d955f26a6 100644
@@ -260,12 +260,14 @@ static int fsl_sai_set_dai_fmt_tr(struct snd_soc_dai *cpu_dai,
 	case SND_SOC_DAIFMT_CBS_CFS:
 		val_cr2 |= FSL_SAI_CR2_BCD_MSTR;
 		val_cr4 |= FSL_SAI_CR4_FSD_MSTR;
+		sai->is_slave_mode = false;
 		break;
 	case SND_SOC_DAIFMT_CBM_CFM:
 		sai->is_slave_mode = true;
 		break;
 	case SND_SOC_DAIFMT_CBS_CFM:
 		val_cr2 |= FSL_SAI_CR2_BCD_MSTR;
+		sai->is_slave_mode = false;
 		break;
 	case SND_SOC_DAIFMT_CBM_CFS:
 		val_cr4 |= FSL_SAI_CR4_FSD_MSTR;
Signature · 1 line
2.20.1
author maintainer
#16 lore raw

PATCH 17/92 ssb: Fix possible NULL pointer dereference in ssb_host_pcmcia_exit

In reply to Sasha Levin

From: YueHaibing <[email protected]>

[ Upstream commit b2c01aab9646ed8ffb7c549afe55d5349c482425 ]

Syzkaller report this:

kasan: GPF could be caused by NULL-ptr deref or user memory access

general protection fault: 0000 [#1] SMP KASAN PTI
CPU: 0 PID: 4492 Comm: syz-executor.0 Not tainted 5.0.0-rc7+ #45
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
RIP: 0010:sysfs_remove_file_ns+0x27/0x70 fs/sysfs/file.c:468
Code: 00 00 00 41 54 55 48 89 fd 53 49 89 d4 48 89 f3 e8 ee 76 9c ff 48 8d 7d 30 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 <80> 3c 02 00 75 2d 48 89 da 48 b8 00 00 00 00 00 fc ff df 48 8b 6d
RSP: 0018:ffff8881e9d9fc00 EFLAGS: 00010206
RAX: dffffc0000000000 RBX: ffffffff900367e0 RCX: ffffffff81a95952
RDX: 0000000000000006 RSI: ffffc90001405000 RDI: 0000000000000030
RBP: 0000000000000000 R08: fffffbfff1fa22ed R09: fffffbfff1fa22ed
R10: 0000000000000001 R11: fffffbfff1fa22ec R12: 0000000000000000
R13: ffffffffc1abdac0 R14: 1ffff1103d3b3f8b R15: 0000000000000000
FS:  00007fe409dc1700(0000) GS:ffff8881f1200000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000001b2d721000 CR3: 00000001e98b6005 CR4: 00000000007606f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
 sysfs_remove_file include/linux/sysfs.h:519 [inline]
 driver_remove_file+0x40/0x50 drivers/base/driver.c:122
 pcmcia_remove_newid_file drivers/pcmcia/ds.c:163 [inline]
 pcmcia_unregister_driver+0x7d/0x2b0 drivers/pcmcia/ds.c:209
 ssb_modexit+0xa/0x1b [ssb]
 __do_sys_delete_module kernel/module.c:1018 [inline]
 __se_sys_delete_module kernel/module.c:961 [inline]
 __x64_sys_delete_module+0x3dc/0x5e0 kernel/module.c:961
 do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x462e99
Code: f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007fe409dc0c58 EFLAGS: 00000246 ORIG_RAX: 00000000000000b0
RAX: ffffffffffffffda RBX: 000000000073bf00 RCX: 0000000000462e99
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 00000000200000c0
RBP: 0000000000000002 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007fe409dc16bc
R13: 00000000004bccaa R14: 00000000006f6bc8 R15: 00000000ffffffff
Modules linked in: ssb(-) 3c59x nvme_core macvlan tap pata_hpt3x3 rt2x00pci null_blk tsc40 pm_notifier_error_inject notifier_error_inject mdio cdc_wdm nf_reject_ipv4 ath9k_common ath9k_hw ath pppox ppp_generic slhc ehci_platform wl12xx wlcore tps6507x_ts ioc4 nf_synproxy_core ide_gd_mod ax25 can_dev iwlwifi can_raw atm tm2_touchkey can_gw can sundance adp5588_keys rt2800mmio rt2800lib rt2x00mmio rt2x00lib eeprom_93cx6 pn533 lru_cache elants_i2c ip_set nfnetlink gameport tipc hampshire nhc_ipv6 nhc_hop nhc_udp nhc_fragment nhc_routing nhc_mobility nhc_dest 6lowpan silead brcmutil nfc mt76_usb mt76 mac80211 iptable_security iptable_raw iptable_mangle iptable_nat nf_nat_ipv4 nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 iptable_filter bpfilter ip6_vti ip_gre sit hsr veth vxcan batman_adv cfg80211 rfkill chnl_net caif nlmon vcan bridge stp llc ip6_gre ip6_tunnel tunnel6 tun joydev mousedev serio_raw ide_pci_generic piix floppy ide_core sch_fq_codel ip_tables x_tables ipv6
 [last unloaded: 3c59x]
Dumping ftrace buffer:
   (ftrace buffer empty)
---[ end trace 3913cbf8011e1c05 ]---

In ssb_modinit, it does not fail SSB init when ssb_host_pcmcia_init failed, however in ssb_modexit, ssb_host_pcmcia_exit calls pcmcia_unregister_driver unconditionally, which may tigger a NULL pointer dereference issue as above.

Fixes 399500da18f7 ("ssb: pick PCMCIA host code support from b43 driver")
---
 drivers/ssb/bridge_pcmcia_80211.c | 9 +++++++--
 1 file changed, 7 insertions(+), 2 deletions(-)
drivers/ssb/bridge_pcmcia_80211.c +7 -2
index d70568ea02d53..2ff7d90e166ac 100644
@@ -113,16 +113,21 @@ static struct pcmcia_driver ssb_host_pcmcia_driver = {
 	.resume		= ssb_host_pcmcia_resume,
 };
 
+static int pcmcia_init_failed;
+
 /*
  * These are not module init/exit functions!
  * The module_pcmcia_driver() helper cannot be used here.
  */
 int ssb_host_pcmcia_init(void)
 {
-	return pcmcia_register_driver(&ssb_host_pcmcia_driver);
+	pcmcia_init_failed = pcmcia_register_driver(&ssb_host_pcmcia_driver);
+
+	return pcmcia_init_failed;
 }
 
 void ssb_host_pcmcia_exit(void)
 {
-	pcmcia_unregister_driver(&ssb_host_pcmcia_driver);
+	if (!pcmcia_init_failed)
+		pcmcia_unregister_driver(&ssb_host_pcmcia_driver);
 }
Signature · 1 line
2.20.1
author maintainer
#15 lore raw

PATCH 16/92 at76c50x-usb: Don't register led_trigger if usb_register_driver failed

In reply to Sasha Levin

From: YueHaibing <[email protected]>

[ Upstream commit 09ac2694b0475f96be895848687ebcbba97eeecf ]

Syzkaller report this:

[ 1213.468581] BUG: unable to handle kernel paging request at fffffbfff83bf338
[ 1213.469530] #PF error: [normal kernel read fault]
[ 1213.469530] PGD 237fe4067 P4D 237fe4067 PUD 237e60067 PMD 1c868b067 PTE 0
[ 1213.473514] Oops: 0000 [#1] SMP KASAN PTI
[ 1213.473514] CPU: 0 PID: 6321 Comm: syz-executor.0 Tainted: G         C        5.1.0-rc3+ #8
[ 1213.473514] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
[ 1213.473514] RIP: 0010:strcmp+0x31/0xa0
[ 1213.473514] Code: 00 00 00 00 fc ff df 55 53 48 83 ec 08 eb 0a 84 db 48 89 ef 74 5a 4c 89 e6 48 89 f8 48 89 fa 48 8d 6f 01 48 c1 e8 03 83 e2 07 <42> 0f b6 04 28 38 d0 7f 04 84 c0 75 50 48 89 f0 48 89 f2 0f b6 5d
[ 1213.473514] RSP: 0018:ffff8881f2b7f950 EFLAGS: 00010246
[ 1213.473514] RAX: 1ffffffff83bf338 RBX: ffff8881ea6f7240 RCX: ffffffff825350c6
[ 1213.473514] RDX: 0000000000000000 RSI: ffffffffc1ee19c0 RDI: ffffffffc1df99c0
[ 1213.473514] RBP: ffffffffc1df99c1 R08: 0000000000000001 R09: 0000000000000004
[ 1213.473514] R10: 0000000000000000 R11: ffff8881de353f00 R12: ffff8881ee727900
[ 1213.473514] R13: dffffc0000000000 R14: 0000000000000001 R15: ffffffffc1eeaaf0
[ 1213.473514] FS:  00007fa66fa01700(0000) GS:ffff8881f7200000(0000) knlGS:0000000000000000
[ 1213.473514] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1213.473514] CR2: fffffbfff83bf338 CR3: 00000001ebb9e005 CR4: 00000000007606f0
[ 1213.473514] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 1213.473514] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 1213.473514] PKRU: 55555554
[ 1213.473514] Call Trace:
[ 1213.473514]  led_trigger_register+0x112/0x3f0
[ 1213.473514]  led_trigger_register_simple+0x7a/0x110
[ 1213.473514]  ? 0xffffffffc1c10000
[ 1213.473514]  at76_mod_init+0x77/0x1000 [at76c50x_usb]
[ 1213.473514]  do_one_initcall+0xbc/0x47d
[ 1213.473514]  ? perf_trace_initcall_level+0x3a0/0x3a0
[ 1213.473514]  ? kasan_unpoison_shadow+0x30/0x40
[ 1213.473514]  ? kasan_unpoison_shadow+0x30/0x40
[ 1213.473514]  do_init_module+0x1b5/0x547
[ 1213.473514]  load_module+0x6405/0x8c10
[ 1213.473514]  ? module_frob_arch_sections+0x20/0x20
[ 1213.473514]  ? kernel_read_file+0x1e6/0x5d0
[ 1213.473514]  ? find_held_lock+0x32/0x1c0
[ 1213.473514]  ? cap_capable+0x1ae/0x210
[ 1213.473514]  ? __do_sys_finit_module+0x162/0x190
[ 1213.473514]  __do_sys_finit_module+0x162/0x190
[ 1213.473514]  ? __ia32_sys_init_module+0xa0/0xa0
[ 1213.473514]  ? __mutex_unlock_slowpath+0xdc/0x690
[ 1213.473514]  ? wait_for_completion+0x370/0x370
[ 1213.473514]  ? vfs_write+0x204/0x4a0
[ 1213.473514]  ? do_syscall_64+0x18/0x450
[ 1213.473514]  do_syscall_64+0x9f/0x450
[ 1213.473514]  entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 1213.473514] RIP: 0033:0x462e99
[ 1213.473514] Code: f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
[ 1213.473514] RSP: 002b:00007fa66fa00c58 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
[ 1213.473514] RAX: ffffffffffffffda RBX: 000000000073bf00 RCX: 0000000000462e99
[ 1213.473514] RDX: 0000000000000000 RSI: 0000000020000300 RDI: 0000000000000003
[ 1213.473514] RBP: 00007fa66fa00c70 R08: 0000000000000000 R09: 0000000000000000
[ 1213.473514] R10: 0000000000000000 R11: 0000000000000246 R12: 00007fa66fa016bc
[ 1213.473514] R13: 00000000004bcefa R14: 00000000006f6fb0 R15: 0000000000000004

If usb_register failed, no need to call led_trigger_register_simple.

Fixes 1264b951463a ("at76c50x-usb: add driver")
---
 drivers/net/wireless/at76c50x-usb.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/net/wireless/at76c50x-usb.c +2 -2
index dab25136214a4..da14eca2aa2c8 100644
@@ -2582,8 +2582,8 @@ static int __init at76_mod_init(void)
 	if (result < 0)
 		printk(KERN_ERR DRIVER_NAME
 		       ": usb_register failed (status %d)\n", result);
-
-	led_trigger_register_simple("at76_usb-tx", &ledtrig_tx);
+	else
+		led_trigger_register_simple("at76_usb-tx", &ledtrig_tx);
 	return result;
 }
 
Signature · 1 line
2.20.1
author maintainer
#23 lore raw

PATCH 24/92 smpboot: Place the __percpu annotation correctly

In reply to Sasha Levin

From: Sebastian Andrzej Siewior <[email protected]>

[ Upstream commit d4645d30b50d1691c26ff0f8fa4e718b08f8d3bb ]

The test robot reported a wrong assignment of a per-CPU variable which it detected by using sparse and sent a report. The assignment itself is correct. The annotation for sparse was wrong and hence the report. The first pointer is a "normal" pointer and points to the per-CPU memory area. That means that the __percpu annotation has to be moved.

Move the __percpu annotation to pointer which points to the per-CPU area. This change affects only the sparse tool (and is ignored by the compiler).

Cc Linus Torvalds <[email protected]>
Cc Paul E. McKenney <[email protected]>
Cc Peter Zijlstra <[email protected]>
Cc Thomas Gleixner <[email protected]>
Fixes f97f8f06a49fe ("smpboot: Provide infrastructure for percpu hotplug threads")
---
 include/linux/smpboot.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
include/linux/smpboot.h +1 -1
index 12910cf19869c..12a4b09f4d08b 100644
@@ -30,7 +30,7 @@ struct smpboot_thread_data;
  * @thread_comm:	The base name of the thread
  */
 struct smp_hotplug_thread {
-	struct task_struct __percpu	**store;
+	struct task_struct		* __percpu *store;
 	struct list_head		list;
 	int				(*thread_should_run)(unsigned int cpu);
 	void				(*thread_fn)(unsigned int cpu);
Signature · 1 line
2.20.1
author maintainer
#22 lore raw

PATCH 23/92 x86/build: Move _etext to actual end of .text

In reply to Sasha Levin

From: Kees Cook <[email protected]>

[ Upstream commit 392bef709659abea614abfe53cf228e7a59876a4 ]

When building x86 with Clang LTO and CFI, CFI jump regions are automatically added to the end of the .text section late in linking. As a result, the _etext position was being labelled before the appended jump regions, causing confusion about where the boundaries of the executable region actually are in the running kernel, and broke at least the fault injection code. This moves the _etext mark to outside (and immediately after) the .text area, as it already the case on other architectures (e.g. arm64, arm).

---
 arch/x86/kernel/vmlinux.lds.S | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
arch/x86/kernel/vmlinux.lds.S +3 -3
index 17e1e60b6b400..68dd72248919b 100644
@@ -110,11 +110,11 @@ SECTIONS
 		*(.text.__x86.indirect_thunk)
 		__indirect_thunk_end = .;
 #endif
-
-		/* End of text section */
-		_etext = .;
 	} :text = 0x9090
 
+	/* End of text section */
+	_etext = .;
+
 	NOTES :text :note
 
 	EXCEPTION_TABLE(16) :text = 0x9090
Signature · 1 line
2.20.1
author maintainer
#25 lore raw

PATCH 26/92 mm/uaccess: Use 'unsigned long' to placate UBSAN warnings on older GCC versions

In reply to Sasha Levin

From: Peter Zijlstra <[email protected]>

[ Upstream commit 29da93fea3ea39ab9b12270cc6be1b70ef201c9e ]

Randy reported objtool triggered on his (GCC-7.4) build:

lib/strncpy_from_user.o: warning: objtool: strncpy_from_user()+0x315: call to __ubsan_handle_add_overflow() with UACCESS enabled lib/strnlen_user.o: warning: objtool: strnlen_user()+0x337: call to __ubsan_handle_sub_overflow() with UACCESS enabled

This is due to UBSAN generating signed-overflow-UB warnings where it should not. Prior to GCC-8 UBSAN ignored -fwrapv (which the kernel uses through -fno-strict-overflow).

Make the functions use 'unsigned long' throughout.

---
 lib/strncpy_from_user.c | 5 +++--
 lib/strnlen_user.c      | 4 ++--
 2 files changed, 5 insertions(+), 4 deletions(-)
lib/strncpy_from_user.c +3 -2
index e0af6ff73d146..f8b1e3cb716b9 100644
@@ -20,10 +20,11 @@
  * hit it), 'max' is the address space maximum (and we return
  * -EFAULT if we hit it).
  */
-static inline long do_strncpy_from_user(char *dst, const char __user *src, long count, unsigned long max)
+static inline long do_strncpy_from_user(char *dst, const char __user *src,
+					unsigned long count, unsigned long max)
 {
 	const struct word_at_a_time constants = WORD_AT_A_TIME_CONSTANTS;
-	long res = 0;
+	unsigned long res = 0;
 
 	/*
 	 * Truncate 'max' to the user-specified limit, so that
lib/strnlen_user.c +2 -2
index 3a5f2b366d84e..1c87bfa63db7f 100644
@@ -27,7 +27,7 @@
 static inline long do_strnlen_user(const char __user *src, unsigned long count, unsigned long max)
 {
 	const struct word_at_a_time constants = WORD_AT_A_TIME_CONSTANTS;
-	long align, res = 0;
+	unsigned long align, res = 0;
 	unsigned long c;
 
 	/*
@@ -41,7 +41,7 @@ static inline long do_strnlen_user(const char __user *src, unsigned long count,
 	 * Do everything aligned. But that means that we
 	 * need to also expand the maximum..
 	 */
-	align = (sizeof(long) - 1) & (unsigned long)src;
+	align = (sizeof(unsigned long) - 1) & (unsigned long)src;
 	src -= align;
 	max += align;
 
Signature · 1 line
2.20.1
author maintainer
#24 lore raw

PATCH 25/92 x86/mm: Remove in_nmi() warning from 64-bit implementation of vmalloc_fault()

In reply to Sasha Levin

From: Jiri Kosina <[email protected]>

[ Upstream commit a65c88e16f32aa9ef2e8caa68ea5c29bd5eb0ff0 ]

In-NMI warnings have been added to vmalloc_fault() via:

ebc8827f75 ("x86: Barf when vmalloc and kmemcheck faults happen in NMI")

back in the time when our NMI entry code could not cope with nested NMIs.

These days, it's perfectly fine to take a fault in NMI context and we don't have to care about the fact that IRET from the fault handler might cause NMI nesting.

This warning has already been removed from 32-bit implementation of vmalloc_fault() in:

6863ea0cda8 ("x86/mm: Remove in_nmi() warning from vmalloc_fault()")

but the 64-bit version was omitted.

Remove the bogus warning also from 64-bit implementation of vmalloc_fault().

Cc Andy Lutomirski <[email protected]>
Cc Borislav Petkov <[email protected]>
Cc Dave Hansen <[email protected]>
Cc Frederic Weisbecker <[email protected]>
Cc Joerg Roedel <[email protected]>
Cc Linus Torvalds <[email protected]>
Cc Peter Zijlstra <[email protected]>
Cc Thomas Gleixner <[email protected]>
Fixes 6863ea0cda8 ("x86/mm: Remove in_nmi() warning from vmalloc_fault()")
---
 arch/x86/mm/fault.c | 2 --
 1 file changed, 2 deletions(-)
arch/x86/mm/fault.c +0 -2
index c4dffae5d9390..462c5c30b9a21 100644
@@ -373,8 +373,6 @@ static noinline int vmalloc_fault(unsigned long address)
 	if (!(address >= VMALLOC_START && address < VMALLOC_END))
 		return -1;
 
-	WARN_ON_ONCE(in_nmi());
-
 	/*
 	 * Copy kernel mappings over when needed. This can also
 	 * happen within a race in page table update. In the later
Signature · 1 line
2.20.1
author maintainer
#30 lore raw

PATCH 31/92 media: ov6650: Move v4l2_clk_get() to ov6650_video_probe() helper

In reply to Sasha Levin

From: Janusz Krzysztofik <[email protected]>

[ Upstream commit ccdd85d518d8b9320ace1d87271f0ba2175f21fa ]

In preparation for adding asynchronous subdevice support to the driver, don't acquire v4l2_clk from the driver .probe() callback as that may fail if the clock is provided by a bridge driver which may be not yet initialized. Move the v4l2_clk_get() to ov6650_video_probe() helper which is going to be converted to v4l2_subdev_internal_ops.registered() callback, executed only when the bridge driver is ready.

---
 drivers/media/i2c/soc_camera/ov6650.c | 25 ++++++++++++++-----------
 1 file changed, 14 insertions(+), 11 deletions(-)
drivers/media/i2c/soc_camera/ov6650.c +14 -11
index 1e4783b51a351..c4004888bfd39 100644
@@ -839,9 +839,16 @@ static int ov6650_video_probe(struct i2c_client *client)
 	u8		pidh, pidl, midh, midl;
 	int		ret;
 
+	priv->clk = v4l2_clk_get(&client->dev, NULL);
+	if (IS_ERR(priv->clk)) {
+		ret = PTR_ERR(priv->clk);
+		dev_err(&client->dev, "v4l2_clk request err: %d\n", ret);
+		return ret;
+	}
+
 	ret = ov6650_s_power(&priv->subdev, 1);
 	if (ret < 0)
-		return ret;
+		goto eclkput;
 
 	/*
 	 * check and show product ID and manufacturer ID
@@ -876,6 +883,11 @@ static int ov6650_video_probe(struct i2c_client *client)
 
 done:
 	ov6650_s_power(&priv->subdev, 0);
+	if (!ret)
+		return 0;
+eclkput:
+	v4l2_clk_put(priv->clk);
+
 	return ret;
 }
 
@@ -1033,18 +1045,9 @@ static int ov6650_probe(struct i2c_client *client,
 	priv->code	  = MEDIA_BUS_FMT_YUYV8_2X8;
 	priv->colorspace  = V4L2_COLORSPACE_JPEG;
 
-	priv->clk = v4l2_clk_get(&client->dev, NULL);
-	if (IS_ERR(priv->clk)) {
-		ret = PTR_ERR(priv->clk);
-		goto eclkget;
-	}
-
 	ret = ov6650_video_probe(client);
-	if (ret) {
-		v4l2_clk_put(priv->clk);
-eclkget:
+	if (ret)
 		v4l2_ctrl_handler_free(&priv->hdl);
-	}
 
 	return ret;
 }
Signature · 1 line
2.20.1
author maintainer
#28 lore raw

PATCH 29/92 dmaengine: at_xdmac: remove BUG_ON macro in tasklet

In reply to Sasha Levin

From: Nicolas Ferre <[email protected]>

[ Upstream commit e2c114c06da2d9ffad5b16690abf008d6696f689 ]

Even if this case shouldn't happen when controller is properly programmed, it's still better to avoid dumping a kernel Oops for this.
As the sequence may happen only for debugging purposes, log the error and just finish the tasklet call.

---
 drivers/dma/at_xdmac.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)
drivers/dma/at_xdmac.c +5 -1
index af24c5bf32d69..8aa3ccf42e55a 100644
@@ -1608,7 +1608,11 @@ static void at_xdmac_tasklet(unsigned long data)
 					struct at_xdmac_desc,
 					xfer_node);
 		dev_vdbg(chan2dev(&atchan->chan), "%s: desc 0x%p\n", __func__, desc);
-		BUG_ON(!desc->active_xfer);
+		if (!desc->active_xfer) {
+			dev_err(chan2dev(&atchan->chan), "Xfer not active: exiting");
+			spin_unlock_bh(&atchan->lock);
+			return;
+		}
 
 		txd = &desc->tx_dma_desc;
 
Signature · 7 lines
2.20.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
author maintainer
#31 lore raw

PATCH 32/92 media: au0828: stop video streaming only when last user stops

In reply to Sasha Levin

From: Hans Verkuil <[email protected]>

[ Upstream commit f604f0f5afb88045944567f604409951b5eb6af8 ]

If the application was streaming from both videoX and vbiX, and streaming from videoX was stopped, then the vbi streaming also stopped.

The cause being that stop_streaming for video stopped the subdevs as well, instead of only doing that if dev->streaming_users reached 0.

au0828_stop_vbi_streaming was also wrong since it didn't stop the subdevs at all when dev->streaming_users reached 0.

---
 drivers/media/usb/au0828/au0828-video.c | 13 ++++++++-----
 1 file changed, 8 insertions(+), 5 deletions(-)
drivers/media/usb/au0828/au0828-video.c +8 -5
index 7b2fe1b56039e..1ff66e7e26a81 100644
@@ -799,9 +799,9 @@ int au0828_start_analog_streaming(struct vb2_queue *vq, unsigned int count)
 			return rc;
 		}
 
+		v4l2_device_call_all(&dev->v4l2_dev, 0, video, s_stream, 1);
+
 		if (vq->type == V4L2_BUF_TYPE_VIDEO_CAPTURE) {
-			v4l2_device_call_all(&dev->v4l2_dev, 0, video,
-						s_stream, 1);
 			dev->vid_timeout_running = 1;
 			mod_timer(&dev->vid_timeout, jiffies + (HZ / 10));
 		} else if (vq->type == V4L2_BUF_TYPE_VBI_CAPTURE) {
@@ -821,10 +821,11 @@ static void au0828_stop_streaming(struct vb2_queue *vq)
 
 	dprintk(1, "au0828_stop_streaming called %d\n", dev->streaming_users);
 
-	if (dev->streaming_users-- == 1)
+	if (dev->streaming_users-- == 1) {
 		au0828_uninit_isoc(dev);
+		v4l2_device_call_all(&dev->v4l2_dev, 0, video, s_stream, 0);
+	}
 
-	v4l2_device_call_all(&dev->v4l2_dev, 0, video, s_stream, 0);
 	dev->vid_timeout_running = 0;
 	del_timer_sync(&dev->vid_timeout);
 
@@ -853,8 +854,10 @@ void au0828_stop_vbi_streaming(struct vb2_queue *vq)
 	dprintk(1, "au0828_stop_vbi_streaming called %d\n",
 		dev->streaming_users);
 
-	if (dev->streaming_users-- == 1)
+	if (dev->streaming_users-- == 1) {
 		au0828_uninit_isoc(dev);
+		v4l2_device_call_all(&dev->v4l2_dev, 0, video, s_stream, 0);
+	}
 
 	spin_lock_irqsave(&dev->slock, flags);
 	if (dev->isoc_ctl.vbi_buf != NULL) {
Signature · 1 line
2.20.1
author maintainer
#29 lore raw

PATCH 30/92 media: coda: clear error return value before picture run

In reply to Sasha Levin

From: Philipp Zabel <[email protected]>

[ Upstream commit bbeefa7357a648afe70e7183914c87c3878d528d ]

The error return value is not written by some firmware codecs, such as MPEG-2 decode on CodaHx4. Clear the error return value before starting the picture run to avoid misinterpreting unrelated values returned by sequence initialization as error return value.

---
 drivers/media/platform/coda/coda-bit.c | 3 +++
 1 file changed, 3 insertions(+)
drivers/media/platform/coda/coda-bit.c +3 -0
index d76511c1c1e3f..a4639813cf35d 100644
@@ -1829,6 +1829,9 @@ static int coda_prepare_decode(struct coda_ctx *ctx)
 	/* Clear decode success flag */
 	coda_write(dev, 0, CODA_RET_DEC_PIC_SUCCESS);
 
+	/* Clear error return value */
+	coda_write(dev, 0, CODA_RET_DEC_PIC_ERR_MB);
+
 	trace_coda_dec_pic_run(ctx, meta);
 
 	coda_command_async(ctx, CODA_COMMAND_PIC_RUN);
Signature · 1 line
2.20.1
author maintainer
#14 lore raw

PATCH 15/92 net: cw1200: fix a NULL pointer dereference

In reply to Sasha Levin

From: Kangjie Lu <[email protected]>

[ Upstream commit 0ed2a005347400500a39ea7c7318f1fea57fb3ca ]

In case create_singlethread_workqueue fails, the fix free the hardware and returns NULL to avoid NULL pointer dereference.

---
 drivers/net/wireless/cw1200/main.c | 5 +++++
 1 file changed, 5 insertions(+)
drivers/net/wireless/cw1200/main.c +5 -0
index 0e51e27d2e3f1..317daa968e037 100644
@@ -345,6 +345,11 @@ static struct ieee80211_hw *cw1200_init_common(const u8 *macaddr,
 	mutex_init(&priv->wsm_cmd_mux);
 	mutex_init(&priv->conf_mutex);
 	priv->workqueue = create_singlethread_workqueue("cw1200_wq");
+	if (!priv->workqueue) {
+		ieee80211_free_hw(hw);
+		return NULL;
+	}
+
 	sema_init(&priv->scan.lock, 1);
 	INIT_WORK(&priv->scan.work, cw1200_scan_work);
 	INIT_DELAYED_WORK(&priv->scan.probe_work, cw1200_probe_work);
Signature · 1 line
2.20.1
author maintainer
#11 lore raw

PATCH 12/92 driver core: platform: Fix the usage of platform device name(pdev->name)

In reply to Sasha Levin

From: Venkata Narendra Kumar Gutta <[email protected]>

[ Upstream commit edb16da34b084c66763f29bee42b4e6bb33c3d66 ]

Platform core is using pdev->name as the platform device name to do the binding of the devices with the drivers. But, when the platform driver overrides the platform device name with dev_set_name(), the pdev->name is pointing to a location which is freed and becomes an invalid parameter to do the binding match.

use-after-free instance:

[   33.325013] BUG: KASAN: use-after-free in strcmp+0x8c/0xb0
[   33.330646] Read of size 1 at addr ffffffc10beae600 by task modprobe
[   33.339068] CPU: 5 PID: 518 Comm: modprobe Tainted:
			G S      W  O      4.19.30+ #3
[   33.346835] Hardware name: MTP (DT)
[   33.350419] Call trace:
[   33.352941]  dump_backtrace+0x0/0x3b8
[   33.356713]  show_stack+0x24/0x30
[   33.360119]  dump_stack+0x160/0x1d8
[   33.363709]  print_address_description+0x84/0x2e0
[   33.368549]  kasan_report+0x26c/0x2d0
[   33.372322]  __asan_report_load1_noabort+0x2c/0x38
[   33.377248]  strcmp+0x8c/0xb0
[   33.380306]  platform_match+0x70/0x1f8
[   33.384168]  __driver_attach+0x78/0x3a0
[   33.388111]  bus_for_each_dev+0x13c/0x1b8
[   33.392237]  driver_attach+0x4c/0x58
[   33.395910]  bus_add_driver+0x350/0x560
[   33.399854]  driver_register+0x23c/0x328
[   33.403886]  __platform_driver_register+0xd0/0xe0

So, use dev_name(&pdev->dev), which fetches the platform device name from the kobject(dev->kobj->name) of the device instead of the pdev->name.

---
 drivers/base/platform.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)
drivers/base/platform.c +4 -4
index 065fcc4be263a..071dd053a917b 100644
@@ -796,7 +796,7 @@ static ssize_t modalias_show(struct device *dev, struct device_attribute *a,
 	if (len != -ENODEV)
 		return len;
 
-	len = snprintf(buf, PAGE_SIZE, "platform:%s\n", pdev->name);
+	len = snprintf(buf, PAGE_SIZE, "platform:%s\n", dev_name(&pdev->dev));
 
 	return (len >= PAGE_SIZE) ? (PAGE_SIZE - 1) : len;
 }
@@ -872,7 +872,7 @@ static int platform_uevent(struct device *dev, struct kobj_uevent_env *env)
 		return rc;
 
 	add_uevent_var(env, "MODALIAS=%s%s", PLATFORM_MODULE_PREFIX,
-			pdev->name);
+			dev_name(&pdev->dev));
 	return 0;
 }
 
@@ -881,7 +881,7 @@ static const struct platform_device_id *platform_match_id(
 			struct platform_device *pdev)
 {
 	while (id->name[0]) {
-		if (strcmp(pdev->name, id->name) == 0) {
+		if (strcmp(dev_name(&pdev->dev), id->name) == 0) {
 			pdev->id_entry = id;
 			return id;
 		}
@@ -925,7 +925,7 @@ static int platform_match(struct device *dev, struct device_driver *drv)
 		return platform_match_id(pdrv->id_table, pdev) != NULL;
 
 	/* fall-back to driver name match */
-	return (strcmp(pdev->name, drv->name) == 0);
+	return (strcmp(dev_name(&pdev->dev), drv->name) == 0);
 }
 
 #ifdef CONFIG_PM_SLEEP
Signature · 1 line
2.20.1
author maintainer
#9 lore raw

PATCH 10/92 dmaengine: pl330: _stop: clear interrupt status

In reply to Sasha Levin

From: Sugar Zhang <[email protected]>

[ Upstream commit 2da254cc7908105a60a6bb219d18e8dced03dcb9 ]

This patch kill instructs the DMAC to immediately terminate execution of a thread. and then clear the interrupt status, at last, stop generating interrupts for DMA_SEV. to guarantee the next dma start is clean. otherwise, one interrupt maybe leave to next start and make some mistake.

we can reporduce the problem as follows:

DMASEV: modify the event-interrupt resource, and if the INTEN sets function as interrupt, the DMAC will set irq<event_num> HIGH to generate interrupt. write INTCLR to clear interrupt.

	DMA EXECUTING INSTRUCTS		DMA TERMINATE
		|				|
		|				|
	       ...			      _stop
		|				|
		|			spin_lock_irqsave
	     DMASEV				|
		|				|
		|			    mask INTEN
		|				|
		|			     DMAKILL
		|				|
		|			spin_unlock_irqrestore

in above case, a interrupt was left, and if we unmask INTEN, the DMAC will set irq<event_num> HIGH to generate interrupt.

to fix this, do as follows:

	DMA EXECUTING INSTRUCTS		DMA TERMINATE
		|				|
		|				|
	       ...			      _stop
		|				|
		|			spin_lock_irqsave
	     DMASEV				|
		|				|
		|			     DMAKILL
		|				|
		|			   clear INTCLR
		|			    mask INTEN
		|				|
		|			spin_unlock_irqrestore
---
 drivers/dma/pl330.c | 10 +++++++---
 1 file changed, 7 insertions(+), 3 deletions(-)
drivers/dma/pl330.c +7 -3
index 95619ee33112c..799c182c3eacc 100644
@@ -1006,6 +1006,7 @@ static void _stop(struct pl330_thread *thrd)
 {
 	void __iomem *regs = thrd->dmac->base;
 	u8 insn[6] = {0, 0, 0, 0, 0, 0};
+	u32 inten = readl(regs + INTEN);
 
 	if (_state(thrd) == PL330_STATE_FAULT_COMPLETING)
 		UNTIL(thrd, PL330_STATE_FAULTING | PL330_STATE_KILLING);
@@ -1018,10 +1019,13 @@ static void _stop(struct pl330_thread *thrd)
 
 	_emit_KILL(0, insn);
 
-	/* Stop generating interrupts for SEV */
-	writel(readl(regs + INTEN) & ~(1 << thrd->ev), regs + INTEN);
-
 	_execute_DBGINSN(thrd, insn, is_manager(thrd));
+
+	/* clear the event */
+	if (inten & (1 << thrd->ev))
+		writel(1 << thrd->ev, regs + INTCLR);
+	/* Stop generating interrupts for SEV */
+	writel(inten & ~(1 << thrd->ev), regs + INTEN);
 }
 
 /* Start doing req 'idx' of thread 'thrd' */
Signature · 1 line
2.20.1
author maintainer
#7 lore raw

PATCH 8/92 rtc: 88pm860x: prevent use-after-free on device remove

In reply to Sasha Levin

From: Sven Van Asbroeck <[email protected]>

[ Upstream commit f22b1ba15ee5785aa028384ebf77dd39e8e47b70 ]

The device's remove() attempts to shut down the delayed_work scheduled on the kernel-global workqueue by calling flush_scheduled_work().

Unfortunately, flush_scheduled_work() does not prevent the delayed_work from re-scheduling itself. The delayed_work might run after the device has been removed, and touch the already de-allocated info structure. This is a potential use-after-free.

Fix by calling cancel_delayed_work_sync() during remove(): this ensures that the delayed work is properly cancelled, is no longer running, and is not able to re-schedule itself.

This issue was detected with the help of Coccinelle.

---
 drivers/rtc/rtc-88pm860x.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/rtc/rtc-88pm860x.c +1 -1
index 19e53b3b8e005..166faae3a59cd 100644
@@ -414,7 +414,7 @@ static int pm860x_rtc_remove(struct platform_device *pdev)
 	struct pm860x_rtc_info *info = platform_get_drvdata(pdev);
 
 #ifdef VRTC_CALIBRATION
-	flush_scheduled_work();
+	cancel_delayed_work_sync(&info->calib_work);
 	/* disable measurement */
 	pm860x_set_bits(info->i2c, PM8607_MEAS_EN2, MEAS2_VRTC, 0);
 #endif	/* VRTC_CALIBRATION */
Signature · 1 line
2.20.1
author maintainer
#4 lore raw

PATCH 5/92 ASoC: imx: fix fiq dependencies

In reply to Sasha Levin

From: Arnd Bergmann <[email protected]>

[ Upstream commit ea751227c813ab833609afecfeedaf0aa26f327e ]

During randconfig builds, I occasionally run into an invalid configuration of the freescale FIQ sound support:

WARNING: unmet direct dependencies detected for SND_SOC_IMX_PCM_FIQ
Depends on [m]: SOUND [=y] && !UML && SND [=y] && SND_SOC [=y] && SND_IMX_SOC [=m]
Selected by [y]:
- SND_SOC_FSL_SPDIF [=y] && SOUND [=y] && !UML && SND [=y] && SND_SOC [=y] && SND_IMX_SOC [=m]!=n && (MXC_TZIC [=n] || MXC_AVIC [=y])

sound/soc/fsl/imx-ssi.o: In function `imx_ssi_remove':
imx-ssi.c:(.text+0x28): undefined reference to imx_pcm_fiq_exit' sound/soc/fsl/imx-ssi.o: In function imx_ssi_probe':
imx-ssi.c:(.text+0xa64): undefined reference to `imx_pcm_fiq_init'

The Kconfig warning is a result of the symbol being defined inside of the "if SND_IMX_SOC" block, and is otherwise harmless. The link error is more tricky and happens with SND_SOC_IMX_SSI=y, which may or may not imply FIQ support. However, if SND_SOC_FSL_SSI is set to =m at the same time, that selects SND_SOC_IMX_PCM_FIQ as a loadable module dependency, which then causes a link failure from imx-ssi.

The solution here is to make SND_SOC_IMX_PCM_FIQ built-in whenever one of its potential users is built-in.

Fixes ff40260f79dc ("ASoC: fsl: refine DMA/FIQ dependencies")
---
 sound/soc/fsl/Kconfig | 9 +++++----
 1 file changed, 5 insertions(+), 4 deletions(-)
sound/soc/fsl/Kconfig +5 -4
index 3066e068aae5c..d420995ed45bf 100644
@@ -171,16 +171,17 @@ config SND_MPC52xx_SOC_EFIKA
 
 endif # SND_POWERPC_SOC
 
+config SND_SOC_IMX_PCM_FIQ
+	tristate
+	default y if SND_SOC_IMX_SSI=y && (SND_SOC_FSL_SSI=m || SND_SOC_FSL_SPDIF=m) && (MXC_TZIC || MXC_AVIC)
+	select FIQ
+
 if SND_IMX_SOC
 
 config SND_SOC_IMX_SSI
 	tristate
 	select SND_SOC_FSL_UTILS
 
-config SND_SOC_IMX_PCM_FIQ
-	tristate
-	select FIQ
-
 comment "SoC Audio support for Freescale i.MX boards:"
 
 config SND_MXC_SOC_WM1133_EV1
Signature · 1 line
2.20.1
author maintainer
#1 lore raw

PATCH 2/92 cxgb4: Fix error path in cxgb4_init_module

In reply to Sasha Levin

From: YueHaibing <[email protected]>

[ Upstream commit a3147770bea76c8dbad73eca3a24c2118da5e719 ]

BUG: unable to handle kernel paging request at ffffffffa016a270
PGD 3270067 P4D 3270067 PUD 3271063 PMD 230bbd067 PTE 0
Oops: 0000 [#1
CPU: 0 PID: 6134 Comm: modprobe Not tainted 5.1.0+ #33
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.9.3-0-ge2fc41e-prebuilt.qemu-project.org 04/01/2014
RIP: 0010:atomic_notifier_chain_register+0x24/0x60
Code: 1f 80 00 00 00 00 55 48 89 e5 41 54 49 89 f4 53 48 89 fb e8 ae b4 38 01 48 8b 53 38 48 8d 4b 38 48 85 d2 74 20 45 8b 44 24 10 <44> 3b 42 10 7e 08 eb 13 44 39 42 10 7c 0d 48 8d 4a 08 48 8b 52 08
RSP: 0018:ffffc90000e2bc60 EFLAGS: 00010086
RAX: 0000000000000292 RBX: ffffffff83467240 RCX: ffffffff83467278
RDX: ffffffffa016a260 RSI: ffffffff83752140 RDI: ffffffff83467240
RBP: ffffc90000e2bc70 R08: 0000000000000000 R09: 0000000000000001
R10: 0000000000000000 R11: 00000000014fa61f R12: ffffffffa01c8260
R13: ffff888231091e00 R14: 0000000000000000 R15: ffffc90000e2be78
FS:  00007fbd8d7cd540(0000) GS:ffff888237a00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffffffa016a270 CR3: 000000022c7e3000 CR4: 00000000000006f0
Call Trace:
 register_inet6addr_notifier+0x13/0x20
 cxgb4_init_module+0x6c/0x1000 [cxgb4
 ? 0xffffffffa01d7000
 do_one_initcall+0x6c/0x3cc
 ? do_init_module+0x22/0x1f1
 ? rcu_read_lock_sched_held+0x97/0xb0
 ? kmem_cache_alloc_trace+0x325/0x3b0
 do_init_module+0x5b/0x1f1
 load_module+0x1db1/0x2690
 ? m_show+0x1d0/0x1d0
 __do_sys_finit_module+0xc5/0xd0
 __x64_sys_finit_module+0x15/0x20
 do_syscall_64+0x6b/0x1d0
 entry_SYSCALL_64_after_hwframe+0x49/0xbe

If pci_register_driver fails, register inet6addr_notifier is pointless. This patch fix the error path in cxgb4_init_module.

Fixes b5a02f503caa ("cxgb4 : Update ipv6 address handling api")
---
 drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c | 15 ++++++++++++---
 1 file changed, 12 insertions(+), 3 deletions(-)
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c +12 -3
index a3e1498ca67ce..3b96622de8ff2 100644
@@ -5061,15 +5061,24 @@ static int __init cxgb4_init_module(void)
 
 	ret = pci_register_driver(&cxgb4_driver);
 	if (ret < 0)
-		debugfs_remove(cxgb4_debugfs_root);
+		goto err_pci;
 
 #if IS_ENABLED(CONFIG_IPV6)
 	if (!inet6addr_registered) {
-		register_inet6addr_notifier(&cxgb4_inet6addr_notifier);
-		inet6addr_registered = true;
+		ret = register_inet6addr_notifier(&cxgb4_inet6addr_notifier);
+		if (ret)
+			pci_unregister_driver(&cxgb4_driver);
+		else
+			inet6addr_registered = true;
 	}
 #endif
 
+	if (ret == 0)
+		return ret;
+
+err_pci:
+	debugfs_remove(cxgb4_debugfs_root);
+
 	return ret;
 }
 
Signature · 1 line
2.20.1