Skip to contentSkip to conversation

PCI: sysfs: Ignore lockdep for remove attribute

RFC PATCH Applied [email protected] 2 participants 3 messages May 26, 2019 – Jun 21, 2019 PCI

lore
Share & tools
lore
#0 lore raw

RFC PATCH 1/1 PCI: sysfs: Ignore lockdep for remove attribute

From: Marek Vasut <[email protected]>

On ARM64 R-Car Gen3 R8A7795 system with Intel NVMe SSD inserted into the PCIe slot, with CONFIG_PROVE_LOCKING=y enabled in the kernel config, the following lockdep warning can be triggered:

  $ lspci
  01:00.0 Class 0108: 8086:f1a5	# This is the NVMe SSD
  00:00.0 Class 0604: 1912:0025	# This is the PCIe root port
  $ echo 1 > /sys/class/pci_bus/0000\:00/device/0000\:00\:00.0/remove
  nvme nvme0: failed to set APST feature (-19)

============================================
WARNING: possible recursive locking detected 5.2.0-rc1-next-20190524-00018-gd76fa47ee507 #57 Not tainted
--------------------------------------------
sh/1616 is trying to acquire lock:
(____ptrval____) (kn->count#21){++++}, at: kernfs_remove_by_name_ns+0x4c/0x98

but task is already holding lock:
(____ptrval____) (kn->count#21){++++}, at: kernfs_remove_self+0xec/0x150

other info that might help us debug this:

   Possible unsafe locking scenario:
         CPU0
         ----
    lock(kn->count#21);
    lock(kn->count#21);

*** DEADLOCK ***

May be due to missing lock nesting notation

4 locks held by sh/1616:
#0: (____ptrval____) (sb_writers#4){.+.+}, at: vfs_write+0x190/0x1b0
#1: (____ptrval____) (&of->mutex){+.+.}, at: kernfs_fop_write+0xb4/0x1f0 #2: (____ptrval____) (kn->count#21){++++}, at: kernfs_remove_self+0xec/0x150 #3: (____ptrval____) (pci_rescan_remove_lock){+.+.}, at: pci_lock_rescan_remove+0x1c/0x28

  stack backtrace:
  CPU: 0 PID: 1616 Comm: sh Not tainted 5.2.0-rc1-next-20190524-00018-gd76fa47ee507 #57
  Hardware name: Renesas Salvator-X 2nd version board based on r8a7795 ES2.0+ (DT)
  Call trace:
   dump_backtrace+0x0/0x130
   show_stack+0x14/0x20
   dump_stack+0xd4/0x11c
   __lock_acquire+0x1df8/0x1e58
   lock_acquire+0xdc/0x258
   __kernfs_remove+0x290/0x2f8
   kernfs_remove_by_name_ns+0x4c/0x98
   remove_files.isra.0+0x38/0x78
   sysfs_remove_group+0x4c/0xa0
   sysfs_remove_groups+0x34/0x50
   device_remove_attrs+0x50/0x70
   device_del+0x13c/0x350
   pci_remove_bus_device+0x78/0x100
   pci_remove_bus_device+0x34/0x100
   pci_stop_and_remove_bus_device_locked+0x24/0x38
   remove_store+0x88/0x98
   dev_attr_store+0x14/0x28
   sysfs_kf_write+0x48/0x70
   kernfs_fop_write+0xe4/0x1f0
   __vfs_write+0x18/0x40
   vfs_write+0xa4/0x1b0
   ksys_write+0x64/0xe8
   __arm64_sys_write+0x18/0x20
   el0_svc_common.constprop.0+0x90/0x168
   el0_svc_compat_handler+0x18/0x20
   el0_svc_compat+0x8/0x10
  pci_bus 0000:01: busn_res: [bus 01] is released

The crash is not isolated to NVMe SSDs, but pretty much any other PCIe device will trigger it as well ; empty slot will not. The NVMe SSD was just available for this particular test, Intel e1000 or IGB ethernet triggers the same.

The lockdep complains about trying to acquire the same lock from the same process again, however that is not true. What really happens is that every "remove" sysfs attribute of a PCI device has the same lockdep key, which then confuses lockdep and triggers this warning on two unrelated locks.

The echo 1 > /sys/class/pci_bus/0000:00/device/0000:00:00.0/remove triggers drivers/pci/pci-sysfs.c remove_store(), which first calls device_remove_file_self() on /sys/class/pci_bus/0000:00/device/0000:00:00.0/remove file. This requires calling kernfs_break_active_protection(), since kernfs_fop_open() holds a rwsem lock on the file, using rwsem_acquire_read(&kn->dep_map, 0, 1, _RET_IP_); in kernfs_get_active(), and the kernfs_break_active_protection() releases the lock, allowing the file to be safely removed. The lock is reinstated by calling kernfs_unbreak_active_protection() after the removal. This rwsem operation has a small side-effect in that it registers a lockdep class with the kernfs/sysfs attribute key and this is now in lockdep cache.

The remove_store() continues by calling pci_stop_and_remove_bus_device_locked(), which calls pci_stop_and_remove_bus_device(), pci_remove_bus_device(), device_del() on the subdevices. The interesting one is PCI device 00:01.0 and specifically it's "remove" attribute again, on which the code calls kernfs_remove_by_name_ns(), which calls __kernfs_remove() and then kernfs_drain(), which finally requests a rwsem lock using rwsem_acquire(&kn->dep_map, 0, 0, _RET_IP_); . This is where the lockdep generates the backtrace as seen at the beginning.

The kernfs_node "kn" in each of the previous paragraphs is different kernfs node, however the lockdep key for kn->dep_map is the same. This is because when the "remove" sysfs attibute is created in __kernfs_create_file(), the "key" passed in is the same.

The "key" is assigned to the attribute via drivers/pci/probe.c:pci_device_add(), which calls device_add(&dev->dev) defined in drivers/base/core.c. The device_add() calls device_add_attrs(), device_add_groups(), sysfs_create_groups(), fs/sysfs/group.c:sysfs_create_group(), internal_create_group() and create_files(). The create_files() iterates over all attribute tables associted with "dev" device and calls sysfs_add_file_mode_ns() from fs/sysfs/file.c, which ends up calling __kernfs_create_file() with key = attr->key ?: (struct lock_class_key *)&attr->skey; .

The attribute list gets assigned to the "dev" device in pci_alloc_dev() and points to const struct device_type pci_dev_type in drivers/pci/pci-sysfs.c , which contains the attribute groups and then arrays of sysfs attributes. Since these arrays are static and constant, each and every newly allocated PCI device triggers creation of kernfs objects with the same attribute pointer and thus the same attribute key pointer, and thus the same lockdep key.

This patch marks the "remove" sysfs attribute with __ATTR_IGNORE_LOCKDEP() as it is safe to ignore the lockdep check between different "remove" kernfs instances. However, the better solution might be to allocate new attribute key for every newly allocated PCI device.

From: Marek Vasut <[email protected]>
Cc: Geert Uytterhoeven <[email protected]>
Cc: Phil Edworthy <[email protected]>
Cc: Simon Horman <[email protected]>
Cc: Tejun Heo <[email protected]>
Cc: Wolfram Sang <[email protected]>
Cc: [email protected]
To: [email protected]
---
NOTE: The "rescan" attribute has similar issues
NOTE: This is a different take on https://patchwork.kernel.org/patch/10669333/

---
 drivers/pci/pci-sysfs.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/pci/pci-sysfs.c +1 -1
index 6d27475e39b2..4e83c347de5d 100644
@@ -477,7 +477,7 @@ static ssize_t remove_store(struct device *dev, struct device_attribute *attr,
 		pci_stop_and_remove_bus_device_locked(to_pci_dev(dev));
 	return count;
 }
-static struct device_attribute dev_remove_attr = __ATTR(remove,
+static struct device_attribute dev_remove_attr = __ATTR_IGNORE_LOCKDEP(remove,
 							(S_IWUSR|S_IWGRP),
 							NULL, remove_store);
 
Signature · 1 line
2.20.1
#1 lore raw

[+cc Alan, Eric, Alexander (from previous similar discussions, LKML]

Quoted 5 lines · On Mon, May 27, 2019 at 12:51:51AM +0200, [email protected] wrote:

From: Marek Vasut <[email protected]>

On ARM64 R-Car Gen3 R8A7795 system with Intel NVMe SSD inserted into the PCIe slot, with CONFIG_PROVE_LOCKING=y enabled in the kernel config, the following lockdep warning can be triggered:

As you say, this has nothing to do with the specific platform or NVMe.

It took me longer than I want to admit to figure out the qemu parameters, but I did reproduce this in qemu by making a bridge with a device below it and then removing the bridge:

  $ /usr/bin/qemu-system-x86_64 -M q35 -nographic \
      -drive file=ubuntu.img,if=none,id=disk \
      -device ide-drive,drive=disk,bus=ide.0 \
      -device ioh3420,id=root_port1 \
      -device nec-usb-xhci,bus=root_port1 \
      -kernel ~/linux/arch/x86/boot/bzImage \
      -append "console=ttyS0,115200n8 root=/dev/sda1"
  root@ubuntu:~# lspci -t
  -[0000:00]-+-00.0
             +-01.0
             +-02.0
             +-03.0-[01]----00.0
             +-1f.0
             +-1f.2
             \-1f.3
  root@ubuntu:~# lspci -vs03.0
  00:03.0 PCI bridge: Intel Corporation 7500/5520/5500/X58 I/O Hub PCI Express Root Port 0 (rev 02) (prog-if 00 [Normal decode])
  root@ubuntu:~# lspci -vs01:00.0
  01:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 03) (prog-if 30 [XHCI])
  root@ubuntu:~# echo 1 > /sys/devices/pci0000:00/0000:00:03.0/remove
  <lockdep splat>
Quoted 127 lines
  $ lspci
  01:00.0 Class 0108: 8086:f1a5	# This is the NVMe SSD
  00:00.0 Class 0604: 1912:0025	# This is the PCIe root port
  $ echo 1 > /sys/class/pci_bus/0000\:00/device/0000\:00\:00.0/remove
  nvme nvme0: failed to set APST feature (-19)

============================================
WARNING: possible recursive locking detected 5.2.0-rc1-next-20190524-00018-gd76fa47ee507 #57 Not tainted
--------------------------------------------
sh/1616 is trying to acquire lock:
(____ptrval____) (kn->count#21){++++}, at: kernfs_remove_by_name_ns+0x4c/0x98

but task is already holding lock:
(____ptrval____) (kn->count#21){++++}, at: kernfs_remove_self+0xec/0x150

other info that might help us debug this:

   Possible unsafe locking scenario:
         CPU0
         ----
    lock(kn->count#21);
    lock(kn->count#21);

*** DEADLOCK ***

May be due to missing lock nesting notation

4 locks held by sh/1616:

   #0: (____ptrval____) (sb_writers#4){.+.+}, at: vfs_write+0x190/0x1b0
   #1: (____ptrval____) (&of->mutex){+.+.}, at: kernfs_fop_write+0xb4/0x1f0
   #2: (____ptrval____) (kn->count#21){++++}, at: kernfs_remove_self+0xec/0x150
   #3: (____ptrval____) (pci_rescan_remove_lock){+.+.}, at: pci_lock_rescan_remove+0x1c/0x28
  stack backtrace:
  CPU: 0 PID: 1616 Comm: sh Not tainted 5.2.0-rc1-next-20190524-00018-gd76fa47ee507 #57
  Hardware name: Renesas Salvator-X 2nd version board based on r8a7795 ES2.0+ (DT)
  Call trace:
   dump_backtrace+0x0/0x130
   show_stack+0x14/0x20
   dump_stack+0xd4/0x11c
   __lock_acquire+0x1df8/0x1e58
   lock_acquire+0xdc/0x258
   __kernfs_remove+0x290/0x2f8
   kernfs_remove_by_name_ns+0x4c/0x98
   remove_files.isra.0+0x38/0x78
   sysfs_remove_group+0x4c/0xa0
   sysfs_remove_groups+0x34/0x50
   device_remove_attrs+0x50/0x70
   device_del+0x13c/0x350
   pci_remove_bus_device+0x78/0x100
   pci_remove_bus_device+0x34/0x100
   pci_stop_and_remove_bus_device_locked+0x24/0x38
   remove_store+0x88/0x98
   dev_attr_store+0x14/0x28
   sysfs_kf_write+0x48/0x70
   kernfs_fop_write+0xe4/0x1f0
   __vfs_write+0x18/0x40
   vfs_write+0xa4/0x1b0
   ksys_write+0x64/0xe8
   __arm64_sys_write+0x18/0x20
   el0_svc_common.constprop.0+0x90/0x168
   el0_svc_compat_handler+0x18/0x20
   el0_svc_compat+0x8/0x10
  pci_bus 0000:01: busn_res: [bus 01] is released

The crash is not isolated to NVMe SSDs, but pretty much any other PCIe device will trigger it as well ; empty slot will not. The NVMe SSD was just available for this particular test, Intel e1000 or IGB ethernet triggers the same.

The lockdep complains about trying to acquire the same lock from the same process again, however that is not true. What really happens is that every "remove" sysfs attribute of a PCI device has the same lockdep key, which then confuses lockdep and triggers this warning on two unrelated locks.

The echo 1 > /sys/class/pci_bus/0000:00/device/0000:00:00.0/remove triggers drivers/pci/pci-sysfs.c remove_store(), which first calls device_remove_file_self() on /sys/class/pci_bus/0000:00/device/0000:00:00.0/remove file. This requires calling kernfs_break_active_protection(), since kernfs_fop_open() holds a rwsem lock on the file, using rwsem_acquire_read(&kn->dep_map, 0, 1, _RET_IP_); in kernfs_get_active(), and the kernfs_break_active_protection() releases the lock, allowing the file to be safely removed. The lock is reinstated by calling kernfs_unbreak_active_protection() after the removal. This rwsem operation has a small side-effect in that it registers a lockdep class with the kernfs/sysfs attribute key and this is now in lockdep cache.

The remove_store() continues by calling pci_stop_and_remove_bus_device_locked(), which calls pci_stop_and_remove_bus_device(), pci_remove_bus_device(), device_del() on the subdevices. The interesting one is PCI device 00:01.0 and specifically it's "remove" attribute again, on which the code calls kernfs_remove_by_name_ns(), which calls __kernfs_remove() and then kernfs_drain(), which finally requests a rwsem lock using rwsem_acquire(&kn->dep_map, 0, 0, _RET_IP_); . This is where the lockdep generates the backtrace as seen at the beginning.

The kernfs_node "kn" in each of the previous paragraphs is different kernfs node, however the lockdep key for kn->dep_map is the same. This is because when the "remove" sysfs attibute is created in __kernfs_create_file(), the "key" passed in is the same.

The "key" is assigned to the attribute via drivers/pci/probe.c:pci_device_add(), which calls device_add(&dev->dev) defined in drivers/base/core.c. The device_add() calls device_add_attrs(), device_add_groups(), sysfs_create_groups(), fs/sysfs/group.c:sysfs_create_group(), internal_create_group() and create_files(). The create_files() iterates over all attribute tables associted with "dev" device and calls sysfs_add_file_mode_ns() from fs/sysfs/file.c, which ends up calling __kernfs_create_file() with key = attr->key ?: (struct lock_class_key *)&attr->skey; .

The attribute list gets assigned to the "dev" device in pci_alloc_dev() and points to const struct device_type pci_dev_type in drivers/pci/pci-sysfs.c , which contains the attribute groups and then arrays of sysfs attributes. Since these arrays are static and constant, each and every newly allocated PCI device triggers creation of kernfs objects with the same attribute pointer and thus the same attribute key pointer, and thus the same lockdep key.

This patch marks the "remove" sysfs attribute with __ATTR_IGNORE_LOCKDEP() as it is safe to ignore the lockdep check between different "remove" kernfs instances. However, the better solution might be to allocate new attribute key for every newly allocated PCI device.

Quoted 11 lines

From: Marek Vasut <[email protected]>
Cc: Geert Uytterhoeven <[email protected]>
Cc: Phil Edworthy <[email protected]>
Cc: Simon Horman <[email protected]>
Cc: Tejun Heo <[email protected]>
Cc: Wolfram Sang <[email protected]>
Cc: [email protected]
To: [email protected]
---
NOTE: The "rescan" attribute has similar issues
NOTE: This is a different take on https://patchwork.kernel.org/patch/10669333/

I tried to reproduce this "rescan" problem with the above qemu platform:

  root@ubuntu:~# echo 1 > /sys/class/pci_bus/0000:00/device/0000:00:00.0/remove
  root@ubuntu:~# echo 1 > /sys/class/pci_bus/0000:00/rescan
  root@ubuntu:~# echo 1 > /sys/devices/pci0000:00/0000:00:00.0/remove
  root@ubuntu:~# echo 1 > /sys/devices/pci0000:00/pci_bus/0000:00/rescan

These all worked fine. I didn't see any recent changes that should have fixed this, so I don't know whether it was fixed a different way, or if I'm just not doing the right thing to see it.

drivers/pci/pci-sysfs.c static ssize_t remove_store(struct device *dev, struct device_attribute *attr, · line 482

Quoted 12 lines
drivers/pci/pci-sysfs.c +1 -1
index 6d27475e39b2..4e83c347de5d 100644
@@ -477,7 +477,7 @@ static ssize_t remove_store(struct device *dev, struct device_attribute *attr,
 		pci_stop_and_remove_bus_device_locked(to_pci_dev(dev));
 	return count;
 }
-static struct device_attribute dev_remove_attr = __ATTR(remove,
+static struct device_attribute dev_remove_attr = __ATTR_IGNORE_LOCKDEP(remove,
 							(S_IWUSR|S_IWGRP),
 							NULL, remove_store);

I think this is the same problem solved for USB by 356c05d58af0 ("sysfs: get rid of some lockdep false positives") which used DEVICE_ATTR_IGNORE_LOCKDEP for the USB "remove" files.

e9b526fe7048 ("i2c: suppress lockdep warning on delete_device") does the same for the i2c "delete_device" files.

Here's the original discussion about USB that led to the addition of DEVICE_ATTR_IGNORE_LOCKDEP:
https://lore.kernel.org/r/[email protected]

Bottom line, I think this patch is the right fix, and I'll apply it unless somebody has a better idea.

Bjorn

#2 lore raw
In reply to [email protected]
Quoted 133 lines · On Mon, May 27, 2019 at 12:51:51AM +0200, [email protected] wrote:

From: Marek Vasut <[email protected]>

On ARM64 R-Car Gen3 R8A7795 system with Intel NVMe SSD inserted into the PCIe slot, with CONFIG_PROVE_LOCKING=y enabled in the kernel config, the following lockdep warning can be triggered:

  $ lspci
  01:00.0 Class 0108: 8086:f1a5	# This is the NVMe SSD
  00:00.0 Class 0604: 1912:0025	# This is the PCIe root port
  $ echo 1 > /sys/class/pci_bus/0000\:00/device/0000\:00\:00.0/remove
  nvme nvme0: failed to set APST feature (-19)

============================================
WARNING: possible recursive locking detected 5.2.0-rc1-next-20190524-00018-gd76fa47ee507 #57 Not tainted
--------------------------------------------
sh/1616 is trying to acquire lock:
(____ptrval____) (kn->count#21){++++}, at: kernfs_remove_by_name_ns+0x4c/0x98

but task is already holding lock:
(____ptrval____) (kn->count#21){++++}, at: kernfs_remove_self+0xec/0x150

other info that might help us debug this:

   Possible unsafe locking scenario:
         CPU0
         ----
    lock(kn->count#21);
    lock(kn->count#21);

*** DEADLOCK ***

May be due to missing lock nesting notation

4 locks held by sh/1616:

   #0: (____ptrval____) (sb_writers#4){.+.+}, at: vfs_write+0x190/0x1b0
   #1: (____ptrval____) (&of->mutex){+.+.}, at: kernfs_fop_write+0xb4/0x1f0
   #2: (____ptrval____) (kn->count#21){++++}, at: kernfs_remove_self+0xec/0x150
   #3: (____ptrval____) (pci_rescan_remove_lock){+.+.}, at: pci_lock_rescan_remove+0x1c/0x28
  stack backtrace:
  CPU: 0 PID: 1616 Comm: sh Not tainted 5.2.0-rc1-next-20190524-00018-gd76fa47ee507 #57
  Hardware name: Renesas Salvator-X 2nd version board based on r8a7795 ES2.0+ (DT)
  Call trace:
   dump_backtrace+0x0/0x130
   show_stack+0x14/0x20
   dump_stack+0xd4/0x11c
   __lock_acquire+0x1df8/0x1e58
   lock_acquire+0xdc/0x258
   __kernfs_remove+0x290/0x2f8
   kernfs_remove_by_name_ns+0x4c/0x98
   remove_files.isra.0+0x38/0x78
   sysfs_remove_group+0x4c/0xa0
   sysfs_remove_groups+0x34/0x50
   device_remove_attrs+0x50/0x70
   device_del+0x13c/0x350
   pci_remove_bus_device+0x78/0x100
   pci_remove_bus_device+0x34/0x100
   pci_stop_and_remove_bus_device_locked+0x24/0x38
   remove_store+0x88/0x98
   dev_attr_store+0x14/0x28
   sysfs_kf_write+0x48/0x70
   kernfs_fop_write+0xe4/0x1f0
   __vfs_write+0x18/0x40
   vfs_write+0xa4/0x1b0
   ksys_write+0x64/0xe8
   __arm64_sys_write+0x18/0x20
   el0_svc_common.constprop.0+0x90/0x168
   el0_svc_compat_handler+0x18/0x20
   el0_svc_compat+0x8/0x10
  pci_bus 0000:01: busn_res: [bus 01] is released

The crash is not isolated to NVMe SSDs, but pretty much any other PCIe device will trigger it as well ; empty slot will not. The NVMe SSD was just available for this particular test, Intel e1000 or IGB ethernet triggers the same.

The lockdep complains about trying to acquire the same lock from the same process again, however that is not true. What really happens is that every "remove" sysfs attribute of a PCI device has the same lockdep key, which then confuses lockdep and triggers this warning on two unrelated locks.

The echo 1 > /sys/class/pci_bus/0000:00/device/0000:00:00.0/remove triggers drivers/pci/pci-sysfs.c remove_store(), which first calls device_remove_file_self() on /sys/class/pci_bus/0000:00/device/0000:00:00.0/remove file. This requires calling kernfs_break_active_protection(), since kernfs_fop_open() holds a rwsem lock on the file, using rwsem_acquire_read(&kn->dep_map, 0, 1, _RET_IP_); in kernfs_get_active(), and the kernfs_break_active_protection() releases the lock, allowing the file to be safely removed. The lock is reinstated by calling kernfs_unbreak_active_protection() after the removal. This rwsem operation has a small side-effect in that it registers a lockdep class with the kernfs/sysfs attribute key and this is now in lockdep cache.

The remove_store() continues by calling pci_stop_and_remove_bus_device_locked(), which calls pci_stop_and_remove_bus_device(), pci_remove_bus_device(), device_del() on the subdevices. The interesting one is PCI device 00:01.0 and specifically it's "remove" attribute again, on which the code calls kernfs_remove_by_name_ns(), which calls __kernfs_remove() and then kernfs_drain(), which finally requests a rwsem lock using rwsem_acquire(&kn->dep_map, 0, 0, _RET_IP_); . This is where the lockdep generates the backtrace as seen at the beginning.

The kernfs_node "kn" in each of the previous paragraphs is different kernfs node, however the lockdep key for kn->dep_map is the same. This is because when the "remove" sysfs attibute is created in __kernfs_create_file(), the "key" passed in is the same.

The "key" is assigned to the attribute via drivers/pci/probe.c:pci_device_add(), which calls device_add(&dev->dev) defined in drivers/base/core.c. The device_add() calls device_add_attrs(), device_add_groups(), sysfs_create_groups(), fs/sysfs/group.c:sysfs_create_group(), internal_create_group() and create_files(). The create_files() iterates over all attribute tables associted with "dev" device and calls sysfs_add_file_mode_ns() from fs/sysfs/file.c, which ends up calling __kernfs_create_file() with key = attr->key ?: (struct lock_class_key *)&attr->skey; .

The attribute list gets assigned to the "dev" device in pci_alloc_dev() and points to const struct device_type pci_dev_type in drivers/pci/pci-sysfs.c , which contains the attribute groups and then arrays of sysfs attributes. Since these arrays are static and constant, each and every newly allocated PCI device triggers creation of kernfs objects with the same attribute pointer and thus the same attribute key pointer, and thus the same lockdep key.

This patch marks the "remove" sysfs attribute with __ATTR_IGNORE_LOCKDEP() as it is safe to ignore the lockdep check between different "remove" kernfs instances. However, the better solution might be to allocate new attribute key for every newly allocated PCI device.

Quoted 8 lines

From: Marek Vasut <[email protected]>
Cc: Geert Uytterhoeven <[email protected]>
Cc: Phil Edworthy <[email protected]>
Cc: Simon Horman <[email protected]>
Cc: Tejun Heo <[email protected]>
Cc: Wolfram Sang <[email protected]>
Cc: [email protected]
To: [email protected]

Applied to pci/enumeration for v5.3, thanks, Marek!

Quoted 23 lines

---
NOTE: The "rescan" attribute has similar issues
NOTE: This is a different take on https://patchwork.kernel.org/patch/10669333/

---
 drivers/pci/pci-sysfs.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/pci/pci-sysfs.c +1 -1
index 6d27475e39b2..4e83c347de5d 100644
@@ -477,7 +477,7 @@ static ssize_t remove_store(struct device *dev, struct device_attribute *attr,
 		pci_stop_and_remove_bus_device_locked(to_pci_dev(dev));
 	return count;
 }
-static struct device_attribute dev_remove_attr = __ATTR(remove,
+static struct device_attribute dev_remove_attr = __ATTR_IGNORE_LOCKDEP(remove,
 							(S_IWUSR|S_IWGRP),
 							NULL, remove_store);
 
Signature · 1 line
2.20.1