Skip to contentSkip to conversation

ARM: davinci: da850: Manual pinmux only when PINCTRL not available

PATCH New Adam Ford 2 participants 2 messages Jun 10, 2019 – Jul 14, 2019

lore
Share & tools
lore

Adam Ford

author
#0 lore raw

PATCH 1/1 ARM: davinci: da850: Manual pinmux only when PINCTRL not available

With a recent update to the pinctrl-single driver and the fact that the da850evm has both DM and OF_CONTROL working in both SPL and U-Boot, some of the manual pinmuxing can be setup to only be activated when either the driver doesn't have DM for it, or when CONFIG_PINMUX isn't available (only during SPL). If the code ever shrinks enough to support PINCTRL in SPL, a lot of this can go away. This also remove some manual pinmuxing not needed by SPL to give SPL a little more breathing room.

board/davinci/da8xxevm/da850evm.c +12 -2
index a90b7a3538..5180128db4 100644
@@ -216,21 +216,29 @@ static const struct pinmux_config gpio_pins[] = {
 };
 
 const struct pinmux_resource pinmuxes[] = {
+#ifndef CONFIG_SPL_BUILD
 #ifdef CONFIG_DRIVER_TI_EMAC
 	PINMUX_ITEM(emac_pins_mdio),
 #ifdef CONFIG_DRIVER_TI_EMAC_USE_RMII
 	PINMUX_ITEM(emac_pins_rmii),
 #else
 	PINMUX_ITEM(emac_pins_mii),
-#endif
-#endif
+#endif /* CONFIG_DRIVER_TI_EMAC */
+#endif /* CONFIG_DRIVER_TI_EMAC_USE_RMII */
+#endif /* CONFIG_SPL_BUILD */
 #ifdef CONFIG_SPI_FLASH
+#if !CONFIG_IS_ENABLED(PINCTRL)
 	PINMUX_ITEM(spi1_pins_base),
 	PINMUX_ITEM(spi1_pins_scs0),
 #endif
+#endif
+#if !CONFIG_IS_ENABLED(PINCTRL)
 	PINMUX_ITEM(uart2_pins_txrx),
 	PINMUX_ITEM(uart2_pins_rtscts),
+#endif
+#if !CONFIG_IS_ENABLED(PINCTRL)
 	PINMUX_ITEM(i2c0_pins),
+#endif
 #ifdef CONFIG_NAND_DAVINCI
 	PINMUX_ITEM(emifa_pins_cs3),
 	PINMUX_ITEM(emifa_pins_cs4),
@@ -241,8 +249,10 @@ const struct pinmux_resource pinmuxes[] = {
 #endif
 	PINMUX_ITEM(gpio_pins),
 #ifdef CONFIG_MMC_DAVINCI
+#if !CONFIG_IS_ENABLED(PINCTRL)
 	PINMUX_ITEM(mmc0_pins),
 #endif
+#endif
 };
 
 const int pinmuxes_size = ARRAY_SIZE(pinmuxes);
Signature · 1 line
2.17.1
#1 lore raw

PATCH 1/1 ARM: davinci: da850: Manual pinmux only when PINCTRL not available

board/davinci/da8xxevm/da850evm.c

Quoted 13 lines · Adam Ford

With a recent update to the pinctrl-single driver and the fact that the da850evm has both DM and OF_CONTROL working in both SPL and U-Boot, some of the manual pinmuxing can be setup to only be activated when either the driver doesn't have DM for it, or when CONFIG_PINMUX isn't available (only during SPL). If the code ever shrinks enough to support PINCTRL in SPL, a lot of this can go away. This also remove some manual pinmuxing not needed by SPL to give SPL a little more breathing room.

board/davinci/da8xxevm/da850evm.c +0 -0
index a90b7a3538..5180128db4 100644

Applied to u-boot/master, thanks!

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190714/6584587f/attachment.sig>