Skip to contentSkip to conversation

net: macb: add support for faster clk rates

PATCH In review Ramon Fried 2 participants 10 messages Jul 16, 2019 – Jul 25, 2019 Network drivers

lore
Share & tools
lore
#0 lore raw

PATCH v2 2/6 net: macb: add support for faster clk rates

add support for clock rates higher than 2.4Mhz

---
v2: nothing.

 drivers/net/macb.c | 6 +++++-
 drivers/net/macb.h | 2 ++
 2 files changed, 7 insertions(+), 1 deletion(-)
drivers/net/macb.c +5 -1
index 0032d4e000..0fed43bbe2 100644
@@ -903,8 +903,12 @@ static u32 gem_mdc_clk_div(int id, struct macb_device *macb)
 		config = GEM_BF(CLK, GEM_CLK_DIV48);
 	else if (macb_hz < 160000000)
 		config = GEM_BF(CLK, GEM_CLK_DIV64);
-	else
+	else if (macb_hz < 240000000)
 		config = GEM_BF(CLK, GEM_CLK_DIV96);
+	else if (macb_hz < 320000000)
+		config = GEM_BF(CLK, GEM_CLK_DIV128);
+	else
+		config = GEM_BF(CLK, GEM_CLK_DIV224);
 
 	return config;
 }
drivers/net/macb.h +2 -0
index 8966c793a7..9b16383eba 100644
@@ -613,6 +613,8 @@
 #define GEM_CLK_DIV48				3
 #define GEM_CLK_DIV64				4
 #define GEM_CLK_DIV96				5
+#define GEM_CLK_DIV128				6
+#define GEM_CLK_DIV224				7
 
 /* Constants for MAN register */
 #define MACB_MAN_SOF				1
Signature · 1 line
2.22.0
#1 lore raw

PATCH v2 3/6 net: macb: use bit access macro from header file

macb.h provides macros for reading/setting bitfields, in macb registers and descriptors. use that instead of redefining them in the source file.

---
v2: nothing.

 drivers/net/macb.c | 48 +++++++++++++++-------------------------------
 1 file changed, 15 insertions(+), 33 deletions(-)
drivers/net/macb.c +15 -33
index 0fed43bbe2..a968a4bd06 100644
@@ -77,27 +77,8 @@ struct macb_dma_desc {
 #define MACB_RX_DMA_DESC_SIZE	(DMA_DESC_BYTES(MACB_RX_RING_SIZE))
 #define MACB_TX_DUMMY_DMA_DESC_SIZE	(DMA_DESC_BYTES(1))
 
-#define RXADDR_USED		0x00000001
-#define RXADDR_WRAP		0x00000002
-
 #define RXBUF_FRMLEN_MASK	0x00000fff
-#define RXBUF_FRAME_START	0x00004000
-#define RXBUF_FRAME_END		0x00008000
-#define RXBUF_TYPEID_MATCH	0x00400000
-#define RXBUF_ADDR4_MATCH	0x00800000
-#define RXBUF_ADDR3_MATCH	0x01000000
-#define RXBUF_ADDR2_MATCH	0x02000000
-#define RXBUF_ADDR1_MATCH	0x04000000
-#define RXBUF_BROADCAST		0x80000000
-
 #define TXBUF_FRMLEN_MASK	0x000007ff
-#define TXBUF_FRAME_END		0x00008000
-#define TXBUF_NOCRC		0x00010000
-#define TXBUF_EXHAUSTED		0x08000000
-#define TXBUF_UNDERRUN		0x10000000
-#define TXBUF_MAXRETRY		0x20000000
-#define TXBUF_WRAP		0x40000000
-#define TXBUF_USED		0x80000000
 
 struct macb_device {
 	void			*regs;
@@ -316,9 +297,9 @@ static int _macb_send(struct macb_device *macb, const char *name, void *packet,
 	paddr = dma_map_single(packet, length, DMA_TO_DEVICE);
 
 	ctrl = length & TXBUF_FRMLEN_MASK;
-	ctrl |= TXBUF_FRAME_END;
+	ctrl |= MACB_BIT(TX_LAST);
 	if (tx_head == (MACB_TX_RING_SIZE - 1)) {
-		ctrl |= TXBUF_WRAP;
+		ctrl |= MACB_BIT(TX_WRAP);
 		macb->tx_head = 0;
 	} else {
 		macb->tx_head++;
@@ -340,7 +321,7 @@ static int _macb_send(struct macb_device *macb, const char *name, void *packet,
 		barrier();
 		macb_invalidate_ring_desc(macb, TX);
 		ctrl = macb->tx_ring[tx_head].ctrl;
-		if (ctrl & TXBUF_USED)
+		if (ctrl & MACB_BIT(TX_USED))
 			break;
 		udelay(1);
 	}
@@ -348,9 +329,9 @@ static int _macb_send(struct macb_device *macb, const char *name, void *packet,
 	dma_unmap_single(packet, length, paddr);
 
 	if (i <= MACB_TX_TIMEOUT) {
-		if (ctrl & TXBUF_UNDERRUN)
+		if (ctrl & MACB_BIT(TX_UNDERRUN))
 			printf("%s: TX underrun\n", name);
-		if (ctrl & TXBUF_EXHAUSTED)
+		if (ctrl & MACB_BIT(TX_BUF_EXHAUSTED))
 			printf("%s: TX buffers exhausted in mid frame\n", name);
 	} else {
 		printf("%s: TX timeout\n", name);
@@ -369,14 +350,14 @@ static void reclaim_rx_buffers(struct macb_device *macb,
 
 	macb_invalidate_ring_desc(macb, RX);
 	while (i > new_tail) {
-		macb->rx_ring[i].addr &= ~RXADDR_USED;
+		macb->rx_ring[i].addr &= ~MACB_BIT(RX_USED);
 		i++;
 		if (i > MACB_RX_RING_SIZE)
 			i = 0;
 	}
 
 	while (i < new_tail) {
-		macb->rx_ring[i].addr &= ~RXADDR_USED;
+		macb->rx_ring[i].addr &= ~MACB_BIT(RX_USED);
 		i++;
 	}
 
@@ -396,17 +377,17 @@ static int _macb_recv(struct macb_device *macb, uchar **packetp)
 	for (;;) {
 		macb_invalidate_ring_desc(macb, RX);
 
-		if (!(macb->rx_ring[next_rx_tail].addr & RXADDR_USED))
+		if (!(macb->rx_ring[next_rx_tail].addr & MACB_BIT(RX_USED)))
 			return -EAGAIN;
 
 		status = macb->rx_ring[next_rx_tail].ctrl;
-		if (status & RXBUF_FRAME_START) {
+		if (status & MACB_BIT(RX_SOF)) {
 			if (next_rx_tail != macb->rx_tail)
 				reclaim_rx_buffers(macb, next_rx_tail);
 			macb->wrapped = false;
 		}
 
-		if (status & RXBUF_FRAME_END) {
+		if (status & MACB_BIT(RX_EOF)) {
 			buffer = macb->rx_buffer + 128 * macb->rx_tail;
 			length = status & RXBUF_FRMLEN_MASK;
 
@@ -699,7 +680,7 @@ static int gmac_init_multi_queues(struct macb_device *macb)
 		if (queue_mask & (1 << i))
 			num_queues++;
 
-	macb->dummy_desc->ctrl = TXBUF_USED;
+	macb->dummy_desc->ctrl = MACB_BIT(TX_USED);
 	macb->dummy_desc->addr = 0;
 	flush_dcache_range(macb->dummy_desc_dma, macb->dummy_desc_dma +
 			ALIGN(MACB_TX_DUMMY_DMA_DESC_SIZE, PKTALIGN));
@@ -732,7 +713,7 @@ static int _macb_init(struct macb_device *macb, const char *name)
 	paddr = macb->rx_buffer_dma;
 	for (i = 0; i < MACB_RX_RING_SIZE; i++) {
 		if (i == (MACB_RX_RING_SIZE - 1))
-			paddr |= RXADDR_WRAP;
+			paddr |= MACB_BIT(RX_WRAP);
 		macb->rx_ring[i].addr = paddr;
 		macb->rx_ring[i].ctrl = 0;
 		paddr += 128;
@@ -743,9 +724,10 @@ static int _macb_init(struct macb_device *macb, const char *name)
 	for (i = 0; i < MACB_TX_RING_SIZE; i++) {
 		macb->tx_ring[i].addr = 0;
 		if (i == (MACB_TX_RING_SIZE - 1))
-			macb->tx_ring[i].ctrl = TXBUF_USED | TXBUF_WRAP;
+			macb->tx_ring[i].ctrl = MACB_BIT(TX_USED) |
+				MACB_BIT(TX_WRAP);
 		else
-			macb->tx_ring[i].ctrl = TXBUF_USED;
+			macb->tx_ring[i].ctrl = MACB_BIT(TX_USED);
 	}
 	macb_flush_ring_desc(macb, TX);
 
Signature · 1 line
2.22.0
#3 lore raw

PATCH v2 4/6 net: macb: add support for SGMII phy interface

In reply to Ramon Fried

This patch adds support for the sgmii phy interface, available only to DM users, dictated by current driver design.

---
v2: nothing.

 drivers/net/macb.c | 7 +++++++
 1 file changed, 7 insertions(+)
drivers/net/macb.c +7 -0
index a968a4bd06..cf76270ad8 100644
@@ -759,6 +759,13 @@ static int _macb_init(struct macb_device *macb, const char *name)
 			gem_writel(macb, USRIO, GEM_BIT(RGMII));
 		else
 			gem_writel(macb, USRIO, 0);
+
+		if (macb->phy_interface == PHY_INTERFACE_MODE_SGMII) {
+			unsigned int ncfgr = macb_readl(macb, NCFGR);
+
+			ncfgr |= GEM_BIT(SGMIIEN) | GEM_BIT(PCSSEL);
+			macb_writel(macb, NCFGR, ncfgr);
+		}
 #else
 #if defined(CONFIG_RGMII) || defined(CONFIG_RMII)
 		gem_writel(macb, USRIO, GEM_BIT(RGMII));
Signature · 1 line
2.22.0
#5 lore raw

PATCH v2 5/6 net: macb: add dma_burst_length config

In reply to Ramon Fried

GEM support higher DMA burst writes/reads than the default (4). add configuration structure with dma burst length so it could be applied later to DMA configuration.

---
v2: nothing.

 drivers/net/macb.c | 22 +++++++++++++++++++++-
 1 file changed, 21 insertions(+), 1 deletion(-)
drivers/net/macb.c +21 -1
index cf76270ad8..dc6aa6deda 100644
@@ -82,6 +82,7 @@ struct macb_dma_desc {
 
 struct macb_device {
 	void			*regs;
+	unsigned int		dma_burst_length;
 
 	unsigned int		rx_tail;
 	unsigned int		tx_head;
@@ -118,6 +119,11 @@ struct macb_device {
 	phy_interface_t		phy_interface;
 #endif
 };
+
+struct macb_config {
+	unsigned int		dma_burst_length;
+};
+
 #ifndef CONFIG_DM_ETH
 #define to_macb(_nd) container_of(_nd, struct macb_device, netdev)
 #endif
@@ -1135,8 +1141,13 @@ static int macb_enable_clk(struct udevice *dev)
 }
 #endif
 
+static const struct macb_config default_gem_config = {
+	.dma_burst_length = 16,
+};
+
 static int macb_eth_probe(struct udevice *dev)
 {
+	const struct macb_config *macb_config;
 	struct eth_pdata *pdata = dev_get_platdata(dev);
 	struct macb_device *macb = dev_get_priv(dev);
 	const char *phy_mode;
@@ -1153,6 +1164,11 @@ static int macb_eth_probe(struct udevice *dev)
 
 	macb->regs = (void *)pdata->iobase;
 
+	macb_config = (struct macb_config *)dev_get_driver_data(dev);
+	if (!macb_config)
+		macb_config = &default_gem_config;
+
+	macb->dma_burst_length = macb_config->dma_burst_length;
 #ifdef CONFIG_CLK
 	ret = macb_enable_clk(dev);
 	if (ret)
@@ -1213,12 +1229,16 @@ static int macb_eth_ofdata_to_platdata(struct udevice *dev)
 	return macb_late_eth_ofdata_to_platdata(dev);
 }
 
+static const struct macb_config sama5d4_config = {
+	.dma_burst_length = 4,
+};
+
 static const struct udevice_id macb_eth_ids[] = {
 	{ .compatible = "cdns,macb" },
 	{ .compatible = "cdns,at91sam9260-macb" },
 	{ .compatible = "atmel,sama5d2-gem" },
 	{ .compatible = "atmel,sama5d3-gem" },
-	{ .compatible = "atmel,sama5d4-gem" },
+	{ .compatible = "atmel,sama5d4-gem", .data = (ulong)&sama5d4_config },
 	{ .compatible = "cdns,zynq-gem" },
 	{ }
 };
Signature · 1 line
2.22.0
#7 lore raw

PATCH v2 6/6 net: macb: apply sane DMA configuration

In reply to Ramon Fried

DMA configuration was heavily dependent on the HW defaults, add function to properly set the required fields, including the new dma_burst_length.

---
v2: nothing.

 drivers/net/macb.c | 28 ++++++++++++++++++++++++++++
 1 file changed, 28 insertions(+)
drivers/net/macb.c +28 -0
index dc6aa6deda..035109dc43 100644
@@ -47,6 +47,7 @@ DECLARE_GLOBAL_DATA_PTR;
 
 #define MACB_RX_BUFFER_SIZE		4096
 #define MACB_RX_RING_SIZE		(MACB_RX_BUFFER_SIZE / 128)
+#define RX_BUFFER_MULTIPLE		64
 #define MACB_TX_RING_SIZE		16
 #define MACB_TX_TIMEOUT		1000
 #define MACB_AUTONEG_TIMEOUT	5000000
@@ -697,6 +698,31 @@ static int gmac_init_multi_queues(struct macb_device *macb)
 	return 0;
 }
 
+static void gmac_configure_dma(struct macb_device *macb)
+{
+	u32 buffer_size;
+	u32 dmacfg;
+
+	buffer_size = 128 / RX_BUFFER_MULTIPLE;
+	dmacfg = gem_readl(macb, DMACFG) & ~GEM_BF(RXBS, -1L);
+	dmacfg |= GEM_BF(RXBS, buffer_size);
+
+	if (macb->dma_burst_length)
+		dmacfg = GEM_BFINS(FBLDO, macb->dma_burst_length, dmacfg);
+
+	dmacfg |= GEM_BIT(TXPBMS) | GEM_BF(RXBMS, -1L);
+	dmacfg &= ~GEM_BIT(ENDIA_PKT);
+
+#ifdef CONFIG_SYS_LITTLE_ENDIAN
+		dmacfg &= ~GEM_BIT(ENDIA_DESC);
+#else
+		dmacfg |= GEM_BIT(ENDIA_DESC); /* CPU in big endian */
+#endif
+
+	dmacfg &= ~GEM_BIT(ADDR64);
+	gem_writel(macb, DMACFG, dmacfg);
+}
+
 #ifdef CONFIG_DM_ETH
 static int _macb_init(struct udevice *dev, const char *name)
 #else
@@ -750,6 +776,8 @@ static int _macb_init(struct macb_device *macb, const char *name)
 	macb_writel(macb, TBQP, macb->tx_ring_dma);
 
 	if (macb_is_gem(macb)) {
+		/* Initialize DMA properties */
+		gmac_configure_dma(macb);
 		/* Check the multi queue and initialize the queue for tx */
 		gmac_init_multi_queues(macb);
 
Signature · 1 line
2.22.0