Skip to contentSkip to conversation

imx: Add support for i.MX28 based XEA board

PATCH Superseded Lukasz Majewski 1 participant 1 message Aug 12, 2019

Subsystems (3)

v1 of 6 Superseded Latest is v6 →

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 imx: Add support for i.MX28 based XEA board

From: Mans Rullgard <[email protected]>

This patch introduces support for i.MX28 based XEA board.

This board supports DM/DTS in U-Boot proper as well as DM aware drivers in SPL (u-boot.sb).
More detailed information regarding usage of it can be found in ./board/liebherr/xea/README file.

U-Boot SPL 2019.10-rc1-00233-g6aa549f05c (Aug 12 2019 - 09:23:36 +0200) Trying to boot from MMC1
MMC0: Command 8 timeout (status 0xf0344020)
mmc_load_image_raw_sector: mmc block read error

U-Boot 2019.10-rc1-00233-g6aa549f05c (Aug 12 2019 - 09:23:36 +0200)

CPU:   Freescale i.MX28 rev1.2 at 454 MHz
BOOT:  SSP SPI #3, master, 3V3 NOR
Model: Liebherr (LWE) XEA i.MX28 Board
DRAM:  128 MiB
MMC:   MXS MMC: 0
Loading Environment from SPI Flash... SF: Detected n25q128a13 with page size 256 Bytes, erase size 64 KiB, total 16 MiB
OK
In:    serial
Out:   serial
Err:   serial

Net:
Warning: ethernet at 800f0000 (eth0) using random MAC address - ce:e1:9e:46:f3:a2
eth0: ethernet at 800f0000
Hit any key to stop autoboot: 0

---

Dependencies:
- The whole patch series (1-4) starting at:
https://patchwork.ozlabs.org/patch/1145520/

- Fixes/conversion for i.MX28 spi and emmc (the whole series 1-5):
https://patchwork.ozlabs.org/patch/1145527/

---
 arch/arm/dts/Makefile              |   3 +
 arch/arm/dts/imx28-xea-u-boot.dtsi |  38 +++++
 arch/arm/dts/imx28-xea.dts         | 110 ++++++++++++++
 arch/arm/mach-imx/mxs/Kconfig      |   4 +
 board/liebherr/xea/Kconfig         |  24 +++
 board/liebherr/xea/MAINTAINERS     |   6 +
 board/liebherr/xea/Makefile        |  12 ++
 board/liebherr/xea/README          |  63 ++++++++
 board/liebherr/xea/spl_xea.c       | 301 +++++++++++++++++++++++++++++++++++++
 board/liebherr/xea/xea.c           | 120 +++++++++++++++
 configs/imx28_xea_defconfig        | 103 +++++++++++++
 include/configs/xea.h              | 196 ++++++++++++++++++++++++
 12 files changed, 980 insertions(+)
 create mode 100644 arch/arm/dts/imx28-xea-u-boot.dtsi
 create mode 100644 arch/arm/dts/imx28-xea.dts
 create mode 100644 board/liebherr/xea/Kconfig
 create mode 100644 board/liebherr/xea/MAINTAINERS
 create mode 100644 board/liebherr/xea/Makefile
 create mode 100644 board/liebherr/xea/README
 create mode 100644 board/liebherr/xea/spl_xea.c
 create mode 100644 board/liebherr/xea/xea.c
 create mode 100644 configs/imx28_xea_defconfig
 create mode 100644 include/configs/xea.h
arch/arm/dts/Makefile +3 -0
index 9e7d6d6490..555532b933 100644
@@ -544,6 +544,9 @@ dtb-$(CONFIG_VF610) += vf500-colibri.dtb \
 	vf610-pcm052.dtb \
 	vf610-bk4r1.dtb
 
+dtb-$(CONFIG_MX28) += \
+	imx28-xea.dtb
+
 dtb-$(CONFIG_MX53) += imx53-cx9020.dtb \
 	imx53-kp.dtb \
 	imx53-m53menlo.dtb
arch/arm/dts/imx28-xea-u-boot.dtsi new file +38 -0
new file mode 100644
index 0000000000..59b3bd4c2b
@@ -0,0 +1,38 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019
+ * Lukasz Majewski, DENX Software Engineering, lukma at denx.de
+ *
+ * SPDX-License-Identifier:     GPL-2.0+ or X11
+ */
+
+/*
+ * The minimal augmentation DTS U-Boot file to allow eMMC driver
+ * configuration in SPL for falcon boot.
+ */
+#include "imx28-u-boot.dtsi"
+/ {
+	apb at 80000000 {
+		u-boot,dm-spl;
+
+		apbh at 80000000 {
+			u-boot,dm-spl;
+		};
+
+		apbx at 80040000 {
+			u-boot,dm-spl;
+		};
+	};
+};
+
+&clks {
+	u-boot,dm-spl;
+};
+
+&ssp0 {
+	u-boot,dm-spl;
+};
+
+&ssp3 {
+	u-boot,dm-spl;
+};
arch/arm/dts/imx28-xea.dts new file +110 -0

110 lines not on this page · raw message

arch/arm/mach-imx/mxs/Kconfig +4 -0
index 68072d5a1f..b90d7b6e41 100644
@@ -60,6 +60,9 @@ config TARGET_SC_SPS_1
 config TARGET_TS4600
 	bool "Support TS4600"
 
+config TARGET_XEA
+	bool "Support XEA"
+
 endchoice
 
 config SYS_SOC
@@ -67,6 +70,7 @@ config SYS_SOC
 
 source "board/bluegiga/apx4devkit/Kconfig"
 source "board/freescale/mx28evk/Kconfig"
+source "board/liebherr/xea/Kconfig"
 source "board/ppcag/bg0900/Kconfig"
 source "board/schulercontrol/sc_sps_1/Kconfig"
 source "board/technologic/ts4600/Kconfig"
board/liebherr/xea/Kconfig new file +24 -0
new file mode 100644
index 0000000000..5428de4646
@@ -0,0 +1,24 @@
+if TARGET_XEA
+
+config SYS_BOARD
+	default "xea"
+
+config SYS_VENDOR
+	default "liebherr"
+
+config SYS_SOC
+	default "mxs"
+
+config SYS_CONFIG_NAME
+	default "xea"
+
+config ENV_SIZE
+	default 0x2000
+
+config ENV_SECT_SIZE
+	default 0x10000 if ENV_IS_IN_SPI_FLASH
+
+config ENV_OFFSET
+	default 0x80000 if ENV_IS_IN_SPI_FLASH
+
+endif
board/liebherr/xea/MAINTAINERS new file +6 -0
new file mode 100644
index 0000000000..623184d0f8
@@ -0,0 +1,6 @@
+XEA BOARD
+M:	Lukasz Majewski <[email protected]>
+S:	Maintained
+F:	board/liebherr/xea/
+F:	include/configs/xea.h
+F:	configs/imx28_xea_defconfig
board/liebherr/xea/Makefile new file +12 -0
new file mode 100644
index 0000000000..abf500857f
@@ -0,0 +1,12 @@
+#
+# (C) Copyright 2019
+# Lukasz Majewski, DENX Software Engineering, lukma at denx.de.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y	:= xea.o
+
+ifdef	CONFIG_SPL_BUILD
+obj-y	+= spl_xea.o
+endif
board/liebherr/xea/README new file +63 -0

63 lines not on this page · raw message

board/liebherr/xea/spl_xea.c new file +301 -0

301 lines not on this page · raw message

board/liebherr/xea/xea.c new file +120 -0

120 lines not on this page · raw message

configs/imx28_xea_defconfig new file +103 -0

103 lines not on this page · raw message

include/configs/xea.h new file +196 -0

196 lines not on this page · raw message

Signature · 1 line
2.11.0