Skip to contentSkip to conversation

net: dsa: mt7530: Convert to PHYLINK and add support for port 5

PATCH Superseded René van Dorst 6 participants 20 messages Aug 21, 2019 – Aug 30, 2019

Subsystems (7)

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

v2 cover net: dsa: mt7530: Convert to PHYLINK and add support for port 5

1. net: dsa: mt7530: Convert to PHYLINK API
This patch converts mt7530 to PHYLINK API.
2. dt-bindings: net: dsa: mt7530: Add support for port 5
3. net: dsa: mt7530: Add support for port 5
These 2 patches adding support for port 5 of the switch.

v1->v2:
* Mostly phylink improvements after review.
rfc -> v1:
* Mostly phylink improvements after review.
* Drop phy isolation patches. Adds no value for now.
René van Dorst (3):
net: dsa: mt7530: Convert to PHYLINK API
dt-bindings: net: dsa: mt7530: Add support for port 5
net: dsa: mt7530: Add support for port 5

 .../devicetree/bindings/net/dsa/mt7530.txt    | 218 ++++++++++
 drivers/net/dsa/mt7530.c                      | 371 +++++++++++++++---
 drivers/net/dsa/mt7530.h                      |  61 ++-
 3 files changed, 577 insertions(+), 73 deletions(-)
Signature · 1 line
2.20.1
#1 lore raw

PATCH v2 1/3 net: dsa: mt7530: Convert to PHYLINK API

Convert mt7530 to PHYLINK API

v1->v2:
* Refactor "unsupported" phy_interface part in mt7530_phylink_mac_validate() suggested by Russell King
* Report and return when phylink tries to use autoneg_inband in mt7530_phylink_mac_config() suggested by Russell King
* Refactor port 6 setup in mt7530_phylink_mac_config() rfc->v1:
* Renamed P5_MODE_* to P5_INTF_SEL_*. fits the function more
* Convert if-statement for speed bits to a switch suggested by Daniel Santos
* Refactor flow_control pause bits and don't use state->link in mt7530_phylink_mac_config() suggested by Russell King
* Move MAC tx/rx en/disable to mt7530_phylink_mac_link_up/down() suggested by Russell King
* Always support PHY_INTERFACE_MODE_NA in mt7530_phylink_validate() suggested by Russell King
* Added phylink_set_port_modes() in mt7530_phylink_validate() suggested by Russell King
* Remove dev_err on the end of mt7530_phylink_mac_config() suggested by Russell King

---
 drivers/net/dsa/mt7530.c | 266 +++++++++++++++++++++++++++++----------
 drivers/net/dsa/mt7530.h |  32 +++--
 2 files changed, 211 insertions(+), 87 deletions(-)
drivers/net/dsa/mt7530.c +197 -69
index c48e29486b10..ecc13b57e619 100644
@@ -13,7 +13,7 @@
 #include <linux/of_mdio.h>
 #include <linux/of_net.h>
 #include <linux/of_platform.h>
-#include <linux/phy.h>
+#include <linux/phylink.h>
 #include <linux/regmap.h>
 #include <linux/regulator/consumer.h>
 #include <linux/reset.h>
@@ -633,63 +633,6 @@ mt7530_get_sset_count(struct dsa_switch *ds, int port, int sset)
 	return ARRAY_SIZE(mt7530_mib);
 }
 
-static void mt7530_adjust_link(struct dsa_switch *ds, int port,
-			       struct phy_device *phydev)
-{
-	struct mt7530_priv *priv = ds->priv;
-
-	if (phy_is_pseudo_fixed_link(phydev)) {
-		dev_dbg(priv->dev, "phy-mode for master device = %x\n",
-			phydev->interface);
-
-		/* Setup TX circuit incluing relevant PAD and driving */
-		mt7530_pad_clk_setup(ds, phydev->interface);
-
-		if (priv->id == ID_MT7530) {
-			/* Setup RX circuit, relevant PAD and driving on the
-			 * host which must be placed after the setup on the
-			 * device side is all finished.
-			 */
-			mt7623_pad_clk_setup(ds);
-		}
-	} else {
-		u16 lcl_adv = 0, rmt_adv = 0;
-		u8 flowctrl;
-		u32 mcr = PMCR_USERP_LINK | PMCR_FORCE_MODE;
-
-		switch (phydev->speed) {
-		case SPEED_1000:
-			mcr |= PMCR_FORCE_SPEED_1000;
-			break;
-		case SPEED_100:
-			mcr |= PMCR_FORCE_SPEED_100;
-			break;
-		}
-
-		if (phydev->link)
-			mcr |= PMCR_FORCE_LNK;
-
-		if (phydev->duplex) {
-			mcr |= PMCR_FORCE_FDX;
-
-			if (phydev->pause)
-				rmt_adv = LPA_PAUSE_CAP;
-			if (phydev->asym_pause)
-				rmt_adv |= LPA_PAUSE_ASYM;
-
-			lcl_adv = linkmode_adv_to_lcl_adv_t(
-				phydev->advertising);
-			flowctrl = mii_resolve_flowctrl_fdx(lcl_adv, rmt_adv);
-
-			if (flowctrl & FLOW_CTRL_TX)
-				mcr |= PMCR_TX_FC_EN;
-			if (flowctrl & FLOW_CTRL_RX)
-				mcr |= PMCR_RX_FC_EN;
-		}
-		mt7530_write(priv, MT7530_PMCR_P(port), mcr);
-	}
-}
-
 static int
 mt7530_cpu_port_enable(struct mt7530_priv *priv,
 		       int port)
@@ -698,9 +641,6 @@ mt7530_cpu_port_enable(struct mt7530_priv *priv,
 	mt7530_write(priv, MT7530_PVC_P(port),
 		     PORT_SPEC_TAG);
 
-	/* Setup the MAC by default for the cpu port */
-	mt7530_write(priv, MT7530_PMCR_P(port), PMCR_CPUP_LINK);
-
 	/* Disable auto learning on the cpu port */
 	mt7530_set(priv, MT7530_PSC_P(port), SA_DIS);
 
@@ -731,9 +671,6 @@ mt7530_port_enable(struct dsa_switch *ds, int port,
 
 	mutex_lock(&priv->reg_mutex);
 
-	/* Setup the MAC for the user port */
-	mt7530_write(priv, MT7530_PMCR_P(port), PMCR_USERP_LINK);
-
 	/* Allow the user port gets connected to the cpu port and also
 	 * restore the port matrix if the port is the member of a certain
 	 * bridge.
@@ -742,7 +679,7 @@ mt7530_port_enable(struct dsa_switch *ds, int port,
 	priv->ports[port].enable = true;
 	mt7530_rmw(priv, MT7530_PCR_P(port), PCR_MATRIX_MASK,
 		   priv->ports[port].pm);
-	mt7530_port_set_status(priv, port, 1);
+	mt7530_port_set_status(priv, port, 0);
 
 	mutex_unlock(&priv->reg_mutex);
 
@@ -1232,10 +1169,10 @@ static int
 mt7530_setup(struct dsa_switch *ds)
 {
 	struct mt7530_priv *priv = ds->priv;
-	int ret, i;
-	u32 id, val;
-	struct device_node *dn;
 	struct mt7530_dummy_poll p;
+	struct device_node *dn;
+	u32 id, val;
+	int ret, i;
 
 	/* The parent node of master netdev which holds the common system
 	 * controller also is the container for two GMACs nodes representing
@@ -1305,6 +1242,8 @@ mt7530_setup(struct dsa_switch *ds)
 	val |= MHWTRAP_MANUAL;
 	mt7530_write(priv, MT7530_MHWTRAP, val);
 
+	priv->p6_interface = PHY_INTERFACE_MODE_NA;
+
 	/* Enable and reset MIB counters */
 	mt7530_mib_reset(ds);
 
@@ -1329,6 +1268,191 @@ mt7530_setup(struct dsa_switch *ds)
 	return 0;
 }
 
+static void mt7530_phylink_mac_config(struct dsa_switch *ds, int port,
+				      unsigned int mode,
+				      const struct phylink_link_state *state)
+{
+	struct mt7530_priv *priv = ds->priv;
+	u32 mcr_cur, mcr_new;
+
+	switch (port) {
+	case 0: /* Internal phy */
+	case 1:
+	case 2:
+	case 3:
+	case 4:
+		if (state->interface != PHY_INTERFACE_MODE_GMII)
+			return;
+		break;
+	/* case 5: Port 5 is not supported! */
+	case 6: /* 1st cpu port */
+		if (priv->p6_interface == state->interface)
+			break;
+
+		if (state->interface != PHY_INTERFACE_MODE_RGMII &&
+		    state->interface != PHY_INTERFACE_MODE_TRGMII)
+			return;
+
+		/* Setup TX circuit incluing relevant PAD and driving */
+		mt7530_pad_clk_setup(ds, state->interface);
+
+		if (priv->id == ID_MT7530) {
+			/* Setup RX circuit, relevant PAD and driving on the
+			 * host which must be placed after the setup on the
+			 * device side is all finished.
+			 */
+			mt7623_pad_clk_setup(ds);
+		}
+
+		priv->p6_interface = state->interface;
+		break;
+	default:
+		dev_err(ds->dev, "%s: unsupported port: %i\n", __func__, port);
+		return;
+	}
+
+	if (phylink_autoneg_inband(mode)) {
+		dev_err(ds->dev, "%s: in-band negotiation unsupported\n",
+			__func__);
+		return;
+	}
+
+	mcr_cur = mt7530_read(priv, MT7530_PMCR_P(port));
+	mcr_new = mcr_cur;
+	mcr_new &= ~(PMCR_FORCE_SPEED_1000 | PMCR_FORCE_SPEED_100 |
+		     PMCR_FORCE_FDX | PMCR_TX_FC_EN | PMCR_RX_FC_EN);
+	mcr_new |= PMCR_IFG_XMIT(1) | PMCR_MAC_MODE | PMCR_BACKOFF_EN |
+		   PMCR_BACKPR_EN | PMCR_FORCE_MODE | PMCR_FORCE_LNK;
+
+	switch (state->speed) {
+	case SPEED_1000:
+		mcr_new |= PMCR_FORCE_SPEED_1000;
+		break;
+	case SPEED_100:
+		mcr_new |= PMCR_FORCE_SPEED_100;
+		break;
+	}
+	if (state->duplex == DUPLEX_FULL) {
+		mcr_new |= PMCR_FORCE_FDX;
+		if (state->pause & MLO_PAUSE_TX)
+			mcr_new |= PMCR_TX_FC_EN;
+		if (state->pause & MLO_PAUSE_RX)
+			mcr_new |= PMCR_RX_FC_EN;
+	}
+
+	if (mcr_new != mcr_cur)
+		mt7530_write(priv, MT7530_PMCR_P(port), mcr_new);
+}
+
+static void mt7530_phylink_mac_link_down(struct dsa_switch *ds, int port,
+					 unsigned int mode,
+					 phy_interface_t interface)
+{
+	struct mt7530_priv *priv = ds->priv;
+
+	mt7530_port_set_status(priv, port, 0);
+}
+
+static void mt7530_phylink_mac_link_up(struct dsa_switch *ds, int port,
+				       unsigned int mode,
+				       phy_interface_t interface,
+				       struct phy_device *phydev)
+{
+	struct mt7530_priv *priv = ds->priv;
+
+	mt7530_port_set_status(priv, port, 1);
+}
+
+static void mt7530_phylink_validate(struct dsa_switch *ds, int port,
+				    unsigned long *supported,
+				    struct phylink_link_state *state)
+{
+	__ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
+
+	switch (port) {
+	case 0: /* Internal phy */
+	case 1:
+	case 2:
+	case 3:
+	case 4:
+		if (state->interface != PHY_INTERFACE_MODE_NA &&
+		    state->interface != PHY_INTERFACE_MODE_GMII)
+			goto unsupported;
+		break;
+	/* case 5: Port 5 not supported! */
+	case 6: /* 1st cpu port */
+		if (state->interface != PHY_INTERFACE_MODE_NA &&
+		    state->interface != PHY_INTERFACE_MODE_RGMII &&
+		    state->interface != PHY_INTERFACE_MODE_TRGMII)
+			goto unsupported;
+		break;
+	default:
+		dev_err(ds->dev, "%s: unsupported port: %i\n", __func__, port);
+unsupported:
+		linkmode_zero(supported);
+		return;
+	}
+
+	phylink_set_port_modes(mask);
+	phylink_set(mask, Autoneg);
+
+	if (state->interface != PHY_INTERFACE_MODE_TRGMII) {
+		phylink_set(mask, 10baseT_Half);
+		phylink_set(mask, 10baseT_Full);
+		phylink_set(mask, 100baseT_Half);
+		phylink_set(mask, 100baseT_Full);
+		phylink_set(mask, 1000baseT_Half);
+	}
+
+	phylink_set(mask, 1000baseT_Full);
+
+	phylink_set(mask, Pause);
+	phylink_set(mask, Asym_Pause);
+
+	linkmode_and(supported, supported, mask);
+	linkmode_and(state->advertising, state->advertising, mask);
+}
+
+static int
+mt7530_phylink_mac_link_state(struct dsa_switch *ds, int port,
+			      struct phylink_link_state *state)
+{
+	struct mt7530_priv *priv = ds->priv;
+	u32 pmsr;
+
+	if (port < 0 || port >= MT7530_NUM_PORTS)
+		return -EINVAL;
+
+	pmsr = mt7530_read(priv, MT7530_PMSR_P(port));
+
+	state->link = (pmsr & PMSR_LINK);
+	state->an_complete = state->link;
+	state->duplex = !!(pmsr & PMSR_DPX);
+
+	switch (pmsr & PMSR_SPEED_MASK) {
+	case PMSR_SPEED_10:
+		state->speed = SPEED_10;
+		break;
+	case PMSR_SPEED_100:
+		state->speed = SPEED_100;
+		break;
+	case PMSR_SPEED_1000:
+		state->speed = SPEED_1000;
+		break;
+	default:
+		state->speed = SPEED_UNKNOWN;
+		break;
+	}
+
+	state->pause &= ~(MLO_PAUSE_RX | MLO_PAUSE_TX);
+	if (pmsr & PMSR_RX_FC)
+		state->pause |= MLO_PAUSE_RX;
+	if (pmsr & PMSR_TX_FC)
+		state->pause |= MLO_PAUSE_TX;
+
+	return 1;
+}
+
 static const struct dsa_switch_ops mt7530_switch_ops = {
 	.get_tag_protocol	= mtk_get_tag_protocol,
 	.setup			= mt7530_setup,
@@ -1337,7 +1461,6 @@ static const struct dsa_switch_ops mt7530_switch_ops = {
 	.phy_write		= mt7530_phy_write,
 	.get_ethtool_stats	= mt7530_get_ethtool_stats,
 	.get_sset_count		= mt7530_get_sset_count,
-	.adjust_link		= mt7530_adjust_link,
 	.port_enable		= mt7530_port_enable,
 	.port_disable		= mt7530_port_disable,
 	.port_stp_state_set	= mt7530_stp_state_set,
@@ -1350,6 +1473,11 @@ static const struct dsa_switch_ops mt7530_switch_ops = {
 	.port_vlan_prepare	= mt7530_port_vlan_prepare,
 	.port_vlan_add		= mt7530_port_vlan_add,
 	.port_vlan_del		= mt7530_port_vlan_del,
+	.phylink_validate	= mt7530_phylink_validate,
+	.phylink_mac_link_state = mt7530_phylink_mac_link_state,
+	.phylink_mac_config	= mt7530_phylink_mac_config,
+	.phylink_mac_link_down	= mt7530_phylink_mac_link_down,
+	.phylink_mac_link_up	= mt7530_phylink_mac_link_up,
 };
 
 static const struct of_device_id mt7530_of_match[] = {
drivers/net/dsa/mt7530.h +14 -18
index bfac90f48102..107dd04acede 100644
@@ -198,26 +198,20 @@ enum mt7530_vlan_port_attr {
 #define  PMCR_FORCE_SPEED_100		BIT(2)
 #define  PMCR_FORCE_FDX			BIT(1)
 #define  PMCR_FORCE_LNK			BIT(0)
-#define  PMCR_COMMON_LINK		(PMCR_IFG_XMIT(1) | PMCR_MAC_MODE | \
-					 PMCR_BACKOFF_EN | PMCR_BACKPR_EN | \
-					 PMCR_TX_EN | PMCR_RX_EN | \
-					 PMCR_TX_FC_EN | PMCR_RX_FC_EN)
-#define  PMCR_CPUP_LINK			(PMCR_COMMON_LINK | PMCR_FORCE_MODE | \
-					 PMCR_FORCE_SPEED_1000 | \
-					 PMCR_FORCE_FDX | \
-					 PMCR_FORCE_LNK)
-#define  PMCR_USERP_LINK		PMCR_COMMON_LINK
-#define  PMCR_FIXED_LINK		(PMCR_IFG_XMIT(1) | PMCR_MAC_MODE | \
-					 PMCR_FORCE_MODE | PMCR_TX_EN | \
-					 PMCR_RX_EN | PMCR_BACKPR_EN | \
-					 PMCR_BACKOFF_EN | \
-					 PMCR_FORCE_SPEED_1000 | \
-					 PMCR_FORCE_FDX | \
-					 PMCR_FORCE_LNK)
-#define PMCR_FIXED_LINK_FC		(PMCR_FIXED_LINK | \
-					 PMCR_TX_FC_EN | PMCR_RX_FC_EN)
+#define  PMCR_SPEED_MASK		(PMCR_FORCE_SPEED_100 | \
+					 PMCR_FORCE_SPEED_1000)
 
 #define MT7530_PMSR_P(x)		(0x3008 + (x) * 0x100)
+#define  PMSR_EEE1G			BIT(7)
+#define  PMSR_EEE100M			BIT(6)
+#define  PMSR_RX_FC			BIT(5)
+#define  PMSR_TX_FC			BIT(4)
+#define  PMSR_SPEED_1000		BIT(3)
+#define  PMSR_SPEED_100			BIT(2)
+#define  PMSR_SPEED_10			0x00
+#define  PMSR_SPEED_MASK		(PMSR_SPEED_100 | PMSR_SPEED_1000)
+#define  PMSR_DPX			BIT(1)
+#define  PMSR_LINK			BIT(0)
 
 /* Register for MIB */
 #define MT7530_PORT_MIB_COUNTER(x)	(0x4000 + (x) * 0x100)
@@ -423,6 +417,7 @@ struct mt7530_port {
  * @ports:		Holding the state among ports
  * @reg_mutex:		The lock for protecting among process accessing
  *			registers
+ * @p6_interface	Holding the current port 6 interface
  */
 struct mt7530_priv {
 	struct device		*dev;
@@ -435,6 +430,7 @@ struct mt7530_priv {
 	struct gpio_desc	*reset;
 	unsigned int		id;
 	bool			mcm;
+	phy_interface_t		p6_interface;
 
 	struct mt7530_port	ports[MT7530_NUM_PORTS];
 	/* protect among processes for registers access*/
Signature · 1 line
2.20.1
#2 lore raw

PATCH v2 2/3 dt-bindings: net: dsa: mt7530: Add support for port 5

In reply to René van Dorst

MT7530 port 5 has many modes/configurations.
Update the documentation how to use port 5.

v1->v2:
* Adding extra note about RGMII2 and gpio use.
rfc->v1:
* No change

---
 .../devicetree/bindings/net/dsa/mt7530.txt    | 218 ++++++++++++++++++
 1 file changed, 218 insertions(+)
Documentation/devicetree/bindings/net/dsa/mt7530.txt +218 -0
index 47aa205ee0bd..43993aae3f9c 100644
@@ -35,6 +35,42 @@ Required properties for the child nodes within ports container:
 - phy-mode: String, must be either "trgmii" or "rgmii" for port labeled
 	 "cpu".
 
+Port 5 of the switch is muxed between:
+1. GMAC5: GMAC5 can interface with another external MAC or PHY.
+2. PHY of port 0 or port 4: PHY interfaces with an external MAC like 2nd GMAC
+   of the SOC. Used in many setups where port 0/4 becomes the WAN port.
+   Note: On a MT7621 SOC with integrated switch: 2nd GMAC can only connected to
+	 GMAC5 when the gpios for RGMII2 (GPIO 22-33) are not used and not
+	 connected to external component!
+
+Port 5 modes/configurations:
+1. Port 5 is disabled and isolated: An external phy can interface to the 2nd
+   GMAC of the SOC.
+   In the case of a build-in MT7530 switch, port 5 shares the RGMII bus with 2nd
+   GMAC and an optional external phy. Mind the GPIO/pinctl settings of the SOC!
+2. Port 5 is muxed to PHY of port 0/4: Port 0/4 interfaces with 2nd GMAC.
+   It is a simple MAC to PHY interface, port 5 needs to be setup for xMII mode
+   and RGMII delay.
+3. Port 5 is muxed to GMAC5 and can interface to an external phy.
+   Port 5 becomes an extra switch port.
+   Only works on platform where external phy TX<->RX lines are swapped.
+   Like in the Ubiquiti ER-X-SFP.
+4. Port 5 is muxed to GMAC5 and interfaces with the 2nd GAMC as 2nd CPU port.
+   Currently a 2nd CPU port is not supported by DSA code.
+
+Depending on how the external PHY is wired:
+1. normal: The PHY can only connect to 2nd GMAC but not to the switch
+2. swapped: RGMII TX, RX are swapped; external phy interface with the switch as
+   a ethernet port. But can't interface to the 2nd GMAC.
+
+Based on the DT the port 5 mode is configured.
+
+Driver tries to lookup the phy-handle of the 2nd GMAC of the master device.
+When phy-handle matches PHY of port 0 or 4 then port 5 set-up as mode 2.
+phy-mode must be set, see also example 2 below!
+ * mt7621: phy-mode = "rgmii-txid";
+ * mt7623: phy-mode = "rgmii";
+
 See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional
 required, optional properties and how the integrated switch subnodes must
 be specified.
@@ -94,3 +130,185 @@ Example:
 			};
 		};
 	};
+
+Example 2: MT7621: Port 4 is WAN port: 2nd GMAC -> Port 5 -> PHY port 4.
+
+&eth {
+	status = "okay";
+
+	gmac0: mac@0 {
+		compatible = "mediatek,eth-mac";
+		reg = <0>;
+		phy-mode = "rgmii";
+
+		fixed-link {
+			speed = <1000>;
+			full-duplex;
+			pause;
+		};
+	};
+
+	gmac1: mac@1 {
+		compatible = "mediatek,eth-mac";
+		reg = <1>;
+		phy-mode = "rgmii-txid";
+		phy-handle = <&phy4>;
+	};
+
+	mdio: mdio-bus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Internal phy */
+		phy4: ethernet-phy@4 {
+			reg = <4>;
+		};
+
+		mt7530: switch@1f {
+			compatible = "mediatek,mt7621";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1f>;
+			pinctrl-names = "default";
+			mediatek,mcm;
+
+			resets = <&rstctrl 2>;
+			reset-names = "mcm";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					label = "lan0";
+				};
+
+				port@1 {
+					reg = <1>;
+					label = "lan1";
+				};
+
+				port@2 {
+					reg = <2>;
+					label = "lan2";
+				};
+
+				port@3 {
+					reg = <3>;
+					label = "lan3";
+				};
+
+/* Commented out. Port 4 is handled by 2nd GMAC.
+				port@4 {
+					reg = <4>;
+					label = "lan4";
+				};
+*/
+
+				cpu_port0: port@6 {
+					reg = <6>;
+					label = "cpu";
+					ethernet = <&gmac0>;
+					phy-mode = "rgmii";
+
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+						pause;
+					};
+				};
+			};
+		};
+	};
+};
+
+Example 3: MT7621: Port 5 is connected to external PHY: Port 5 -> external PHY.
+
+&eth {
+	status = "okay";
+
+	gmac0: mac@0 {
+		compatible = "mediatek,eth-mac";
+		reg = <0>;
+		phy-mode = "rgmii";
+
+		fixed-link {
+			speed = <1000>;
+			full-duplex;
+			pause;
+		};
+	};
+
+	mdio: mdio-bus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* External phy */
+		ephy5: ethernet-phy@7 {
+			reg = <7>;
+		};
+
+		mt7530: switch@1f {
+			compatible = "mediatek,mt7621";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1f>;
+			pinctrl-names = "default";
+			mediatek,mcm;
+
+			resets = <&rstctrl 2>;
+			reset-names = "mcm";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					label = "lan0";
+				};
+
+				port@1 {
+					reg = <1>;
+					label = "lan1";
+				};
+
+				port@2 {
+					reg = <2>;
+					label = "lan2";
+				};
+
+				port@3 {
+					reg = <3>;
+					label = "lan3";
+				};
+
+				port@4 {
+					reg = <4>;
+					label = "lan4";
+				};
+
+				port@5 {
+					reg = <5>;
+					label = "lan5";
+					phy-mode = "rgmii";
+					phy-handle = <&ephy5>;
+				};
+
+				cpu_port0: port@6 {
+					reg = <6>;
+					label = "cpu";
+					ethernet = <&gmac0>;
+					phy-mode = "rgmii";
+
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+						pause;
+					};
+				};
+			};
+		};
+	};
+};
Signature · 1 line
2.20.1
#6 lore raw

PATCH v2 3/3 net: dsa: mt7530: Add support for port 5

In reply to René van Dorst

Adding support for port 5.

Port 5 can muxed/interface to:
- internal 5th GMAC of the switch; can be used as 2nd CPU port or as extra port with an external phy for a 6th ethernet port.
- internal PHY of port 0 or 4; Used in most applications so that port 0 or 4 is the WAN port and interfaces with the 2nd GMAC of the SOC.

v1->v2:
* Also report 1000base-x support for port 5 suggested by Russell King
* Reorder variable declaraiant in reverse christmas tree suggested by Daved Miller
* Refactor phy-handle lookup for 2nd GMAC.
* Use of_mdio_parse_addr() instead of do it manualy suggested by Florian Fainelli
* Refactor port 5 setup in mt7530_phylink_mac_config() rfc->v1:
* Removed unnecessary info print suggested by Andrew Lunn
* Added support for MII mode for port 5

---
 drivers/net/dsa/mt7530.c | 145 +++++++++++++++++++++++++++++++++++++--
 drivers/net/dsa/mt7530.h |  29 ++++++++
 2 files changed, 168 insertions(+), 6 deletions(-)
drivers/net/dsa/mt7530.c +139 -6
index ecc13b57e619..43407a9b80ac 100644
@@ -633,6 +633,77 @@ mt7530_get_sset_count(struct dsa_switch *ds, int port, int sset)
 	return ARRAY_SIZE(mt7530_mib);
 }
 
+static void mt7530_setup_port5(struct dsa_switch *ds, phy_interface_t interface)
+{
+	struct mt7530_priv *priv = ds->priv;
+	u8 tx_delay = 0;
+	int val;
+
+	mutex_lock(&priv->reg_mutex);
+
+	val = mt7530_read(priv, MT7530_MHWTRAP);
+
+	val |= MHWTRAP_MANUAL | MHWTRAP_P5_MAC_SEL | MHWTRAP_P5_DIS;
+	val &= ~MHWTRAP_P5_RGMII_MODE & ~MHWTRAP_PHY0_SEL;
+
+	switch (priv->p5_intf_sel) {
+	case P5_INTF_SEL_PHY_P0:
+		/* MT7530_P5_MODE_GPHY_P0: 2nd GMAC -> P5 -> P0 */
+		val |= MHWTRAP_PHY0_SEL;
+		/* fall through */
+	case P5_INTF_SEL_PHY_P4:
+		/* MT7530_P5_MODE_GPHY_P4: 2nd GMAC -> P5 -> P4 */
+		val &= ~MHWTRAP_P5_MAC_SEL & ~MHWTRAP_P5_DIS;
+
+		/* Setup the MAC by default for the cpu port */
+		mt7530_write(priv, MT7530_PMCR_P(5), 0x56300);
+		break;
+	case P5_INTF_SEL_GMAC5:
+		/* MT7530_P5_MODE_GMAC: P5 -> External phy or 2nd GMAC */
+		val &= ~MHWTRAP_P5_DIS;
+		break;
+	case P5_DISABLED:
+		interface = PHY_INTERFACE_MODE_NA;
+		break;
+	default:
+		dev_err(ds->dev, "Unsupported p5_intf_sel %d\n",
+			priv->p5_intf_sel);
+		goto unlock_exit;
+	}
+
+	/* Setup RGMII settings */
+	if (phy_interface_mode_is_rgmii(interface)) {
+		val |= MHWTRAP_P5_RGMII_MODE;
+
+		/* P5 RGMII RX Clock Control: delay setting for 1000M */
+		mt7530_write(priv, MT7530_P5RGMIIRXCR, CSR_RGMII_EDGE_ALIGN);
+
+		/* Don't set delay in DSA mode */
+		if (!dsa_is_dsa_port(priv->ds, 5) &&
+		    (interface == PHY_INTERFACE_MODE_RGMII_TXID ||
+		     interface == PHY_INTERFACE_MODE_RGMII_ID))
+			tx_delay = 4; /* n * 0.5 ns */
+
+		/* P5 RGMII TX Clock Control: delay x */
+		mt7530_write(priv, MT7530_P5RGMIITXCR,
+			     CSR_RGMII_TXC_CFG(0x10 + tx_delay));
+
+		/* reduce P5 RGMII Tx driving, 8mA */
+		mt7530_write(priv, MT7530_IO_DRV_CR,
+			     P5_IO_CLK_DRV(1) | P5_IO_DATA_DRV(1));
+	}
+
+	mt7530_write(priv, MT7530_MHWTRAP, val);
+
+	dev_info(ds->dev, "Setup P5, HWTRAP=0x%x, intf_sel=%s, phy-mode=%s\n",
+		 val, p5_intf_modes(priv->p5_intf_sel), phy_modes(interface));
+
+	priv->p5_interface = interface;
+
+unlock_exit:
+	mutex_unlock(&priv->reg_mutex);
+}
+
 static int
 mt7530_cpu_port_enable(struct mt7530_priv *priv,
 		       int port)
@@ -1169,7 +1240,10 @@ static int
 mt7530_setup(struct dsa_switch *ds)
 {
 	struct mt7530_priv *priv = ds->priv;
+	struct device_node *phy_node;
+	struct device_node *mac_np;
 	struct mt7530_dummy_poll p;
+	phy_interface_t interface;
 	struct device_node *dn;
 	u32 id, val;
 	int ret, i;
@@ -1260,6 +1334,40 @@ mt7530_setup(struct dsa_switch *ds)
 			mt7530_port_disable(ds, i);
 	}
 
+	/* Setup port 5 */
+	priv->p5_intf_sel = P5_DISABLED;
+	interface = PHY_INTERFACE_MODE_NA;
+
+	if (!dsa_is_unused_port(ds, 5)) {
+		priv->p5_intf_sel = P5_INTF_SEL_GMAC5;
+		interface = of_get_phy_mode(ds->ports[5].dn);
+	} else {
+		/* Scan the ethernet nodes. look for GMAC1, lookup used phy */
+		for_each_child_of_node(dn, mac_np) {
+			if (!of_device_is_compatible(mac_np,
+						     "mediatek,eth-mac"))
+				continue;
+
+			ret = of_property_read_u32(mac_np, "reg", &id);
+			if (ret < 0 || id != 1)
+				continue;
+
+			phy_node = of_parse_phandle(mac_np, "phy-handle", 0);
+			if (phy_node->parent == priv->dev->of_node->parent) {
+				interface = of_get_phy_mode(mac_np);
+				id = of_mdio_parse_addr(ds->dev, phy_node);
+				if (id == 0)
+					priv->p5_intf_sel = P5_INTF_SEL_PHY_P0;
+				if (id == 4)
+					priv->p5_intf_sel = P5_INTF_SEL_PHY_P4;
+			}
+			of_node_put(phy_node);
+			break;
+		}
+	}
+
+	mt7530_setup_port5(ds, interface);
+
 	/* Flush the FDB table */
 	ret = mt7530_fdb_cmd(priv, MT7530_FDB_FLUSH, NULL);
 	if (ret < 0)
@@ -1284,7 +1392,16 @@ static void mt7530_phylink_mac_config(struct dsa_switch *ds, int port,
 		if (state->interface != PHY_INTERFACE_MODE_GMII)
 			return;
 		break;
-	/* case 5: Port 5 is not supported! */
+	case 5: /* 2nd cpu port with phy of port 0 or 4 / external phy */
+		if (priv->p5_interface == state->interface)
+			break;
+		if (!phy_interface_mode_is_rgmii(state->interface) &&
+		    state->interface != PHY_INTERFACE_MODE_MII &&
+		    state->interface != PHY_INTERFACE_MODE_GMII)
+			return;
+
+		mt7530_setup_port5(ds, state->interface);
+		break;
 	case 6: /* 1st cpu port */
 		if (priv->p6_interface == state->interface)
 			break;
@@ -1324,6 +1441,10 @@ static void mt7530_phylink_mac_config(struct dsa_switch *ds, int port,
 	mcr_new |= PMCR_IFG_XMIT(1) | PMCR_MAC_MODE | PMCR_BACKOFF_EN |
 		   PMCR_BACKPR_EN | PMCR_FORCE_MODE | PMCR_FORCE_LNK;
 
+	/* Are we connected to external phy */
+	if (port == 5 && dsa_is_user_port(ds, 5))
+		mcr_new |= PMCR_EXT_PHY;
+
 	switch (state->speed) {
 	case SPEED_1000:
 		mcr_new |= PMCR_FORCE_SPEED_1000;
@@ -1379,7 +1500,13 @@ static void mt7530_phylink_validate(struct dsa_switch *ds, int port,
 		    state->interface != PHY_INTERFACE_MODE_GMII)
 			goto unsupported;
 		break;
-	/* case 5: Port 5 not supported! */
+	case 5: /* 2nd cpu port with phy of port 0 or 4 / external phy */
+		if (state->interface != PHY_INTERFACE_MODE_NA &&
+		    !phy_interface_mode_is_rgmii(state->interface) &&
+		    state->interface != PHY_INTERFACE_MODE_MII &&
+		    state->interface != PHY_INTERFACE_MODE_GMII)
+			goto unsupported;
+		break;
 	case 6: /* 1st cpu port */
 		if (state->interface != PHY_INTERFACE_MODE_NA &&
 		    state->interface != PHY_INTERFACE_MODE_RGMII &&
@@ -1396,15 +1523,21 @@ static void mt7530_phylink_validate(struct dsa_switch *ds, int port,
 	phylink_set_port_modes(mask);
 	phylink_set(mask, Autoneg);
 
-	if (state->interface != PHY_INTERFACE_MODE_TRGMII) {
+	if (state->interface == PHY_INTERFACE_MODE_TRGMII) {
+		phylink_set(mask, 1000baseT_Full);
+	} else {
 		phylink_set(mask, 10baseT_Half);
 		phylink_set(mask, 10baseT_Full);
 		phylink_set(mask, 100baseT_Half);
 		phylink_set(mask, 100baseT_Full);
-		phylink_set(mask, 1000baseT_Half);
-	}
 
-	phylink_set(mask, 1000baseT_Full);
+		if (state->interface != PHY_INTERFACE_MODE_MII) {
+			phylink_set(mask, 1000baseT_Half);
+			phylink_set(mask, 1000baseT_Full);
+			if (port == 5)
+				phylink_set(mask, 1000baseX_Full);
+		}
+	}
 
 	phylink_set(mask, Pause);
 	phylink_set(mask, Asym_Pause);
drivers/net/dsa/mt7530.h +29 -0
index 107dd04acede..ccb9da8cad0d 100644
@@ -186,6 +186,7 @@ enum mt7530_vlan_port_attr {
 /* Register for port MAC control register */
 #define MT7530_PMCR_P(x)		(0x3000 + ((x) * 0x100))
 #define  PMCR_IFG_XMIT(x)		(((x) & 0x3) << 18)
+#define  PMCR_EXT_PHY			BIT(17)
 #define  PMCR_MAC_MODE			BIT(16)
 #define  PMCR_FORCE_MODE		BIT(15)
 #define  PMCR_TX_EN			BIT(14)
@@ -245,6 +246,7 @@ enum mt7530_vlan_port_attr {
 
 /* Register for hw trap modification */
 #define MT7530_MHWTRAP			0x7804
+#define  MHWTRAP_PHY0_SEL		BIT(20)
 #define  MHWTRAP_MANUAL			BIT(16)
 #define  MHWTRAP_P5_MAC_SEL		BIT(13)
 #define  MHWTRAP_P6_DIS			BIT(8)
@@ -402,6 +404,30 @@ struct mt7530_port {
 	u16 pvid;
 };
 
+/* Port 5 interface select definitions */
+enum p5_interface_select {
+	P5_DISABLED = 0,
+	P5_INTF_SEL_PHY_P0,
+	P5_INTF_SEL_PHY_P4,
+	P5_INTF_SEL_GMAC5,
+};
+
+static const char *p5_intf_modes(unsigned int p5_interface)
+{
+	switch (p5_interface) {
+	case P5_DISABLED:
+		return "DISABLED";
+	case P5_INTF_SEL_PHY_P0:
+		return "PHY P0";
+	case P5_INTF_SEL_PHY_P4:
+		return "PHY P4";
+	case P5_INTF_SEL_GMAC5:
+		return "GMAC5";
+	default:
+		return "unknown";
+	}
+}
+
 /* struct mt7530_priv -	This is the main data structure for holding the state
  *			of the driver
  * @dev:		The device pointer
@@ -418,6 +444,7 @@ struct mt7530_port {
  * @reg_mutex:		The lock for protecting among process accessing
  *			registers
  * @p6_interface	Holding the current port 6 interface
+ * @p5_intf_sel:	Holding the current port 5 interface select
  */
 struct mt7530_priv {
 	struct device		*dev;
@@ -431,6 +458,8 @@ struct mt7530_priv {
 	unsigned int		id;
 	bool			mcm;
 	phy_interface_t		p6_interface;
+	phy_interface_t		p5_interface;
+	unsigned int		p5_intf_sel;
 
 	struct mt7530_port	ports[MT7530_NUM_PORTS];
 	/* protect among processes for registers access*/
Signature · 1 line
2.20.1
maintainer
#9 lore raw
In reply to René van Dorst
Quoted 8 lines · René van Dorst

1. net: dsa: mt7530: Convert to PHYLINK API
This patch converts mt7530 to PHYLINK API.
2. dt-bindings: net: dsa: mt7530: Add support for port 5
3. net: dsa: mt7530: Add support for port 5
These 2 patches adding support for port 5 of the switch.

v1->v2:
* Mostly phylink improvements after review.

Hi René

You are addressing comments mostly from Russell King. It would of been good to Cc: him on the patchset.

Andrew

#10 lore raw
In reply to René van Dorst

Hi,

tested on BPI-R2 (mt7623) with 2 Problems (already reported to Rene, just to inform everyone)...maybe anybody has an idea

- linux-next (i know it's not part of the series, but a pitfall on testing other devices) seems to break power-regulator somewhere here:

priv->core_pwr = devm_regulator_get(&mdiodev->dev, "core"); returns 517

#define EPROBE_DEFER517/* Driver requests probe retry */

https://elixir.bootlin.com/linux/latest/source/drivers/regulator/core.c#L1726

without linux-next switch came up including dsa-ports

- RX-traffic (run iperf3 -c x.x.x.x -R) is only 780 Mbits/sec (TX=940 Mbits/sec), same measure with 5.3-rc4 gives 940 MBit/s with same devices, maybe caused by changes for mt76x8?

regards Frank

#11 lore raw

tested now also on bpi-r64 (mt7622) v0.1 (rtl8367 switch), without linux-next to avoid power-regulator-problems like on bpi-r2

dmesg without warnings/errors caused by this patches
link came up as desired
iperf3 looks good: 943 Mbits/sec in both directions and no other issues

so it is currently only the rx-throughput-problem on mt7623/bpi-r2

regards Frank

maintainer
#12 lore raw
In reply to René van Dorst

From: René van Dorst <[email protected]>
Date: Wed, 21 Aug 2019 16:45:44 +0200

Quoted 11 lines

1. net: dsa: mt7530: Convert to PHYLINK API
This patch converts mt7530 to PHYLINK API.
2. dt-bindings: net: dsa: mt7530: Add support for port 5
3. net: dsa: mt7530: Add support for port 5
These 2 patches adding support for port 5 of the switch.

v1->v2:
* Mostly phylink improvements after review.
rfc -> v1:
* Mostly phylink improvements after review.
* Drop phy isolation patches. Adds no value for now.

This definitely needs some review before I'll apply it.

Thanks.

maintainer
#13 lore raw
Quoted 9 lines · David Miller

From: René van Dorst <[email protected]>
Date: Wed, 21 Aug 2019 16:45:44 +0200

Quoted 6 lines

1. net: dsa: mt7530: Convert to PHYLINK API
This patch converts mt7530 to PHYLINK API.
2. dt-bindings: net: dsa: mt7530: Add support for port 5
3. net: dsa: mt7530: Add support for port 5
These 2 patches adding support for port 5 of the switch.

Quoted 7 lines
Quoted 5 lines

v1->v2:
* Mostly phylink improvements after review.
rfc -> v1:
* Mostly phylink improvements after review.
* Drop phy isolation patches. Adds no value for now.

This definitely needs some review before I'll apply it.

That would be Russell.

We should try to improve MAINTAINER so that Russell King gets picked by the get_maintainer script.

Andrew

maintainer
#14 lore raw

From: Andrew Lunn <[email protected]>
Date: Fri, 23 Aug 2019 03:09:28 +0200

Quoted 4 lines

That would be Russell.

We should try to improve MAINTAINER so that Russell King gets picked by the get_maintainer script.

Shoule he be added to the mt7530 entry?

maintainer
#15 lore raw
Quoted 9 lines · David Miller

From: Andrew Lunn <[email protected]>
Date: Fri, 23 Aug 2019 03:09:28 +0200

Quoted 4 lines

That would be Russell.

We should try to improve MAINTAINER so that Russell King gets picked by the get_maintainer script.

Shoule he be added to the mt7530 entry?

Hi David

No. I think we need a phylink entry. And then make use of the K: line format to list keywords. I hope that even though changes like this don't touch any files listed as being part of phylink, they will match the keyword and pickup Russell.

I need to do some testing and see if this actually works.

Andrew

#17 lore raw
In reply to David Miller
Quoted 9 lines · David Miller

From: Andrew Lunn <[email protected]>
Date: Fri, 23 Aug 2019 03:09:28 +0200

Quoted 4 lines

That would be Russell.

We should try to improve MAINTAINER so that Russell King gets picked by the get_maintainer script.

Shoule he be added to the mt7530 entry?

Probably some way to make MAINTAINERS pick up on phylink-containing patches. Something like:

K: phylink

maybe?

Signature · 3 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up
According to speedtest.net: 11.9Mbps down 500kbps up
Acked-by Russell King on the v2 series
#18 lore raw
In reply to René van Dorst
Quoted 16 lines · René van Dorst

1. net: dsa: mt7530: Convert to PHYLINK API
This patch converts mt7530 to PHYLINK API.
2. dt-bindings: net: dsa: mt7530: Add support for port 5
3. net: dsa: mt7530: Add support for port 5
These 2 patches adding support for port 5 of the switch.

v1->v2:
* Mostly phylink improvements after review.
rfc -> v1:
* Mostly phylink improvements after review.
* Drop phy isolation patches. Adds no value for now.
René van Dorst (3):
net: dsa: mt7530: Convert to PHYLINK API
dt-bindings: net: dsa: mt7530: Add support for port 5
net: dsa: mt7530: Add support for port 5

Quoted 4 lines
 .../devicetree/bindings/net/dsa/mt7530.txt    | 218 ++++++++++
 drivers/net/dsa/mt7530.c                      | 371 +++++++++++++++---
 drivers/net/dsa/mt7530.h                      |  61 ++-
 3 files changed, 577 insertions(+), 73 deletions(-)

Having looked through this set of patches, I don't see anything from the phylink point of view that concerns me. So, for the series from the phylink perspective:

Thanks.

I did notice a dev_info() in patch 3 that you may like to consider whether they should be printed at info level or debug level. You may keep my ack on the patch when fixing that.

I haven't considered whether the patch passes davem's style requirements for networking code; what I spotted did look like the declarations were upside-down christmas tree.

Signature · 3 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up
According to speedtest.net: 11.9Mbps down 500kbps up
#16 lore raw
In reply to Andrew Lunn
Quoted 9 lines · Andrew Lunn
Quoted 8 lines · David Miller

From: Andrew Lunn <[email protected]>
Date: Fri, 23 Aug 2019 03:09:28 +0200

Quoted 4 lines

That would be Russell.

We should try to improve MAINTAINER so that Russell King gets picked by the get_maintainer script.

Quoted 8 lines
Quoted 1 line

Shoule he be added to the mt7530 entry?

Hi David

No. I think we need a phylink entry. And then make use of the K: line format to list keywords. I hope that even though changes like this don't touch any files listed as being part of phylink, they will match the keyword and pickup Russell.

Note that phylink itself is already covered by

"SFF/SFP/SFP+ MODULE SUPPORT"

but doesn't pick up on keywords.

Signature · 3 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up
According to speedtest.net: 11.9Mbps down 500kbps up
maintainer
#7 lore raw

Re: [PATCH net-next v2 3/3] net: dsa: mt7530: Add support for port 5

In reply to René van Dorst

From: René van Dorst <[email protected]>
Date: Wed, 21 Aug 2019 16:45:47 +0200

drivers/net/dsa/mt7530.c mt7530_get_sset_count(struct dsa_switch *ds, int port, int sset) · line 699

Quoted 2 lines
drivers/net/dsa/mt7530.c +2 -0
+	dev_info(ds->dev, "Setup P5, HWTRAP=0x%x, intf_sel=%s, phy-mode=%s\n",
+		 val, p5_intf_modes(priv->p5_intf_sel), phy_modes(interface));

This is debugging, at best. Please make this a debugging message or remove it entirely.

#8 lore raw

Re: [PATCH net-next v2 3/3] net: dsa: mt7530: Add support for port 5

Hi David,

Quoting David Miller <[email protected]>:

Quoted 8 lines

From: René van Dorst <[email protected]>
Date: Wed, 21 Aug 2019 16:45:47 +0200

drivers/net/dsa/mt7530.c mt7530_get_sset_count(struct dsa_switch *ds, int port, int sset) · line 699

Quoted 2 lines
drivers/net/dsa/mt7530.c +2 -0
+	dev_info(ds->dev, "Setup P5, HWTRAP=0x%x, intf_sel=%s, phy-mode=%s\n",
+		 val, p5_intf_modes(priv->p5_intf_sel), phy_modes(interface));

This is debugging, at best. Please make this a debugging message or remove it entirely.

I change it to a debug message.

If there is nothing else I send a new version with this change also add the tags ack-by Russell King and tested-by Frank Wunderlich.

Greats,

René

#19 lore raw
In reply to Russell King - ARM Linux admin

Hi Russell,

Quoting Russell King - ARM Linux admin <[email protected]>:

Quoted 22 lines · René van Dorst
Quoted 16 lines

1. net: dsa: mt7530: Convert to PHYLINK API
This patch converts mt7530 to PHYLINK API.
2. dt-bindings: net: dsa: mt7530: Add support for port 5
3. net: dsa: mt7530: Add support for port 5
These 2 patches adding support for port 5 of the switch.

v1->v2:
* Mostly phylink improvements after review.
rfc -> v1:
* Mostly phylink improvements after review.
* Drop phy isolation patches. Adds no value for now.
René van Dorst (3):
net: dsa: mt7530: Convert to PHYLINK API
dt-bindings: net: dsa: mt7530: Add support for port 5
net: dsa: mt7530: Add support for port 5

Quoted 4 lines
 .../devicetree/bindings/net/dsa/mt7530.txt    | 218 ++++++++++
 drivers/net/dsa/mt7530.c                      | 371 +++++++++++++++---
 drivers/net/dsa/mt7530.h                      |  61 ++-
 3 files changed, 577 insertions(+), 73 deletions(-)
Quoted 5 lines

Having looked through this set of patches, I don't see anything from the phylink point of view that concerns me. So, for the series from the phylink perspective:

Thanks and thanks for reviewing.

Greats,

René

Quoted 15 lines

Thanks.

I did notice a dev_info() in patch 3 that you may like to consider whether they should be printed at info level or debug level. You may keep my ack on the patch when fixing that.

I haven't considered whether the patch passes davem's style requirements for networking code; what I spotted did look like the declarations were upside-down christmas tree.

--
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up According to speedtest.net: 11.9Mbps down 500kbps up

maintainer
#3 lore raw

Re: [PATCH net-next v2 2/3] dt-bindings: net: dsa: mt7530: Add support for port 5

In reply to René van Dorst
Quoted 11 lines · René van Dorst

MT7530 port 5 has many modes/configurations.
Update the documentation how to use port 5.

v1->v2:
* Adding extra note about RGMII2 and gpio use.
rfc->v1:
* No change

The changelog goes below the '---'

Quoted 52 lines
---
 .../devicetree/bindings/net/dsa/mt7530.txt    | 218 ++++++++++++++++++
 1 file changed, 218 insertions(+)
Documentation/devicetree/bindings/net/dsa/mt7530.txt +36 -0
index 47aa205ee0bd..43993aae3f9c 100644
@@ -35,6 +35,42 @@ Required properties for the child nodes within ports container:
 - phy-mode: String, must be either "trgmii" or "rgmii" for port labeled
 	 "cpu".
 
+Port 5 of the switch is muxed between:
+1. GMAC5: GMAC5 can interface with another external MAC or PHY.
+2. PHY of port 0 or port 4: PHY interfaces with an external MAC like 2nd GMAC
+   of the SOC. Used in many setups where port 0/4 becomes the WAN port.
+   Note: On a MT7621 SOC with integrated switch: 2nd GMAC can only connected to
+	 GMAC5 when the gpios for RGMII2 (GPIO 22-33) are not used and not
+	 connected to external component!
+
+Port 5 modes/configurations:
+1. Port 5 is disabled and isolated: An external phy can interface to the 2nd
+   GMAC of the SOC.
+   In the case of a build-in MT7530 switch, port 5 shares the RGMII bus with 2nd
+   GMAC and an optional external phy. Mind the GPIO/pinctl settings of the SOC!
+2. Port 5 is muxed to PHY of port 0/4: Port 0/4 interfaces with 2nd GMAC.
+   It is a simple MAC to PHY interface, port 5 needs to be setup for xMII mode
+   and RGMII delay.
+3. Port 5 is muxed to GMAC5 and can interface to an external phy.
+   Port 5 becomes an extra switch port.
+   Only works on platform where external phy TX<->RX lines are swapped.
+   Like in the Ubiquiti ER-X-SFP.
+4. Port 5 is muxed to GMAC5 and interfaces with the 2nd GAMC as 2nd CPU port.
+   Currently a 2nd CPU port is not supported by DSA code.
+
+Depending on how the external PHY is wired:
+1. normal: The PHY can only connect to 2nd GMAC but not to the switch
+2. swapped: RGMII TX, RX are swapped; external phy interface with the switch as
+   a ethernet port. But can't interface to the 2nd GMAC.
+
+Based on the DT the port 5 mode is configured.
+
+Driver tries to lookup the phy-handle of the 2nd GMAC of the master device.
+When phy-handle matches PHY of port 0 or 4 then port 5 set-up as mode 2.
+phy-mode must be set, see also example 2 below!
+ * mt7621: phy-mode = "rgmii-txid";
+ * mt7623: phy-mode = "rgmii";
+
 See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional
 required, optional properties and how the integrated switch subnodes must
 be specified.

Documentation/devicetree/bindings/net/dsa/mt7530.txt Example: · line 137

Quoted 8 lines
Documentation/devicetree/bindings/net/dsa/mt7530.txt +5 -0
@@ -94,3 +130,185 @@ Example:
 			};
 		};
 	};
+
+Example 2: MT7621: Port 4 is WAN port: 2nd GMAC -> Port 5 -> PHY port 4.
+
+&eth {
+	status = "okay";

Don't show status in examples.

This should show the complete node.

Quoted 180 lines
Documentation/devicetree/bindings/net/dsa/mt7530.txt +177 -0
+
+	gmac0: mac@0 {
+		compatible = "mediatek,eth-mac";
+		reg = <0>;
+		phy-mode = "rgmii";
+
+		fixed-link {
+			speed = <1000>;
+			full-duplex;
+			pause;
+		};
+	};
+
+	gmac1: mac@1 {
+		compatible = "mediatek,eth-mac";
+		reg = <1>;
+		phy-mode = "rgmii-txid";
+		phy-handle = <&phy4>;
+	};
+
+	mdio: mdio-bus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Internal phy */
+		phy4: ethernet-phy@4 {
+			reg = <4>;
+		};
+
+		mt7530: switch@1f {
+			compatible = "mediatek,mt7621";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1f>;
+			pinctrl-names = "default";
+			mediatek,mcm;
+
+			resets = <&rstctrl 2>;
+			reset-names = "mcm";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					label = "lan0";
+				};
+
+				port@1 {
+					reg = <1>;
+					label = "lan1";
+				};
+
+				port@2 {
+					reg = <2>;
+					label = "lan2";
+				};
+
+				port@3 {
+					reg = <3>;
+					label = "lan3";
+				};
+
+/* Commented out. Port 4 is handled by 2nd GMAC.
+				port@4 {
+					reg = <4>;
+					label = "lan4";
+				};
+*/
+
+				cpu_port0: port@6 {
+					reg = <6>;
+					label = "cpu";
+					ethernet = <&gmac0>;
+					phy-mode = "rgmii";
+
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+						pause;
+					};
+				};
+			};
+		};
+	};
+};
+
+Example 3: MT7621: Port 5 is connected to external PHY: Port 5 -> external PHY.
+
+&eth {
+	status = "okay";
+
+	gmac0: mac@0 {
+		compatible = "mediatek,eth-mac";
+		reg = <0>;
+		phy-mode = "rgmii";
+
+		fixed-link {
+			speed = <1000>;
+			full-duplex;
+			pause;
+		};
+	};
+
+	mdio: mdio-bus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* External phy */
+		ephy5: ethernet-phy@7 {
+			reg = <7>;
+		};
+
+		mt7530: switch@1f {
+			compatible = "mediatek,mt7621";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1f>;
+			pinctrl-names = "default";
+			mediatek,mcm;
+
+			resets = <&rstctrl 2>;
+			reset-names = "mcm";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					label = "lan0";
+				};
+
+				port@1 {
+					reg = <1>;
+					label = "lan1";
+				};
+
+				port@2 {
+					reg = <2>;
+					label = "lan2";
+				};
+
+				port@3 {
+					reg = <3>;
+					label = "lan3";
+				};
+
+				port@4 {
+					reg = <4>;
+					label = "lan4";
+				};
+
+				port@5 {
+					reg = <5>;
+					label = "lan5";
+					phy-mode = "rgmii";
+					phy-handle = <&ephy5>;
+				};
+
+				cpu_port0: port@6 {
+					reg = <6>;
+					label = "cpu";
+					ethernet = <&gmac0>;
+					phy-mode = "rgmii";
+
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+						pause;
+					};
+				};
+			};
+		};
+	};
+};
Signature · 1 line
2.20.1
#4 lore raw

Re: [PATCH net-next v2 2/3] dt-bindings: net: dsa: mt7530: Add support for port 5

Hi Rob,

Quoting Rob Herring <[email protected]>:

Quoted 8 lines · René van Dorst
Quoted 6 lines

MT7530 port 5 has many modes/configurations.
Update the documentation how to use port 5.

Quoted 7 lines
Quoted 4 lines

v1->v2:
* Adding extra note about RGMII2 and gpio use.
rfc->v1:
* No change

The changelog goes below the '---'

Thanks for the review,
I shall fix that.

Quoted 64 lines
Quoted 64 lines
---
 .../devicetree/bindings/net/dsa/mt7530.txt    | 218 ++++++++++++++++++
 1 file changed, 218 insertions(+)
Documentation/devicetree/bindings/net/dsa/mt7530.txt +0 -0
index 47aa205ee0bd..43993aae3f9c 100644
@@ -35,6 +35,42 @@ Required properties for the child nodes within  

ports container:
- phy-mode: String, must be either "trgmii" or "rgmii" for port labeled

Documentation/devicetree/bindings/net/dsa/mt7530.txt +3 -0
 	 "cpu".
 
+Port 5 of the switch is muxed between:
+1. GMAC5: GMAC5 can interface with another external MAC or PHY.
+2. PHY of port 0 or port 4: PHY interfaces with an external MAC  

like 2nd GMAC

Documentation/devicetree/bindings/net/dsa/mt7530.txt +2 -0
+   of the SOC. Used in many setups where port 0/4 becomes the WAN port.
+   Note: On a MT7621 SOC with integrated switch: 2nd GMAC can only  

connected to

Documentation/devicetree/bindings/net/dsa/mt7530.txt +5 -0
+	 GMAC5 when the gpios for RGMII2 (GPIO 22-33) are not used and not
+	 connected to external component!
+
+Port 5 modes/configurations:
+1. Port 5 is disabled and isolated: An external phy can interface  

to the 2nd

Documentation/devicetree/bindings/net/dsa/mt7530.txt +2 -0
+   GMAC of the SOC.
+   In the case of a build-in MT7530 switch, port 5 shares the  

RGMII bus with 2nd
+ GMAC and an optional external phy. Mind the GPIO/pinctl
settings of the SOC!
+2. Port 5 is muxed to PHY of port 0/4: Port 0/4 interfaces with 2nd GMAC.
+ It is a simple MAC to PHY interface, port 5 needs to be setup
for xMII mode

Documentation/devicetree/bindings/net/dsa/mt7530.txt +6 -0
+   and RGMII delay.
+3. Port 5 is muxed to GMAC5 and can interface to an external phy.
+   Port 5 becomes an extra switch port.
+   Only works on platform where external phy TX<->RX lines are swapped.
+   Like in the Ubiquiti ER-X-SFP.
+4. Port 5 is muxed to GMAC5 and interfaces with the 2nd GAMC as  

2nd CPU port.

Documentation/devicetree/bindings/net/dsa/mt7530.txt +5 -0
+   Currently a 2nd CPU port is not supported by DSA code.
+
+Depending on how the external PHY is wired:
+1. normal: The PHY can only connect to 2nd GMAC but not to the switch
+2. swapped: RGMII TX, RX are swapped; external phy interface with  

the switch as

Documentation/devicetree/bindings/net/dsa/mt7530.txt +10 -0
+   a ethernet port. But can't interface to the 2nd GMAC.
+
+Based on the DT the port 5 mode is configured.
+
+Driver tries to lookup the phy-handle of the 2nd GMAC of the master device.
+When phy-handle matches PHY of port 0 or 4 then port 5 set-up as mode 2.
+phy-mode must be set, see also example 2 below!
+ * mt7621: phy-mode = "rgmii-txid";
+ * mt7623: phy-mode = "rgmii";
+
 See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list  

of additional
required, optional properties and how the integrated switch subnodes must be specified.

Documentation/devicetree/bindings/net/dsa/mt7530.txt +0 -0
@@ -94,3 +130,185 @@ Example:
 			};
 		};
Quoted 8 lines

Documentation/devicetree/bindings/net/dsa/mt7530.txt Example: · line 137

Quoted 6 lines
Documentation/devicetree/bindings/net/dsa/mt7530.txt +5 -0
 	};
+
+Example 2: MT7621: Port 4 is WAN port: 2nd GMAC -> Port 5 -> PHY port 4.
+
+&eth {
+	status = "okay";

Don't show status in examples.

OK.

Quoted 2 lines

This should show the complete node.

To be clear, I should take ethernet node from the mt7621.dtsi [0] or mt7623.dtsi
[1] and insert the example below?, right?

Greats,

René

[0]: https://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next.git/tree/drivers/staging/mt7621-dts/mt7621.dtsi#n397
[1]: https://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next.git/tree/arch/arm/boot/dts/mt7623.dtsi#n1023

Quoted 181 lines
Quoted 181 lines
Documentation/devicetree/bindings/net/dsa/mt7530.txt +89 -0
+
+	gmac0: mac@0 {
+		compatible = "mediatek,eth-mac";
+		reg = <0>;
+		phy-mode = "rgmii";
+
+		fixed-link {
+			speed = <1000>;
+			full-duplex;
+			pause;
+		};
+	};
+
+	gmac1: mac@1 {
+		compatible = "mediatek,eth-mac";
+		reg = <1>;
+		phy-mode = "rgmii-txid";
+		phy-handle = <&phy4>;
+	};
+
+	mdio: mdio-bus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Internal phy */
+		phy4: ethernet-phy@4 {
+			reg = <4>;
+		};
+
+		mt7530: switch@1f {
+			compatible = "mediatek,mt7621";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1f>;
+			pinctrl-names = "default";
+			mediatek,mcm;
+
+			resets = <&rstctrl 2>;
+			reset-names = "mcm";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					label = "lan0";
+				};
+
+				port@1 {
+					reg = <1>;
+					label = "lan1";
+				};
+
+				port@2 {
+					reg = <2>;
+					label = "lan2";
+				};
+
+				port@3 {
+					reg = <3>;
+					label = "lan3";
+				};
+
+/* Commented out. Port 4 is handled by 2nd GMAC.
+				port@4 {
+					reg = <4>;
+					label = "lan4";
+				};
+*/
+
+				cpu_port0: port@6 {
+					reg = <6>;
+					label = "cpu";
+					ethernet = <&gmac0>;
+					phy-mode = "rgmii";
+
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+						pause;
+					};
+				};
+			};
+		};
+	};
+};
+
+Example 3: MT7621: Port 5 is connected to external PHY: Port 5 ->  

external PHY.

Documentation/devicetree/bindings/net/dsa/mt7530.txt +88 -1
+
+&eth {
+	status = "okay";
+
+	gmac0: mac@0 {
+		compatible = "mediatek,eth-mac";
+		reg = <0>;
+		phy-mode = "rgmii";
+
+		fixed-link {
+			speed = <1000>;
+			full-duplex;
+			pause;
+		};
+	};
+
+	mdio: mdio-bus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* External phy */
+		ephy5: ethernet-phy@7 {
+			reg = <7>;
+		};
+
+		mt7530: switch@1f {
+			compatible = "mediatek,mt7621";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1f>;
+			pinctrl-names = "default";
+			mediatek,mcm;
+
+			resets = <&rstctrl 2>;
+			reset-names = "mcm";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					label = "lan0";
+				};
+
+				port@1 {
+					reg = <1>;
+					label = "lan1";
+				};
+
+				port@2 {
+					reg = <2>;
+					label = "lan2";
+				};
+
+				port@3 {
+					reg = <3>;
+					label = "lan3";
+				};
+
+				port@4 {
+					reg = <4>;
+					label = "lan4";
+				};
+
+				port@5 {
+					reg = <5>;
+					label = "lan5";
+					phy-mode = "rgmii";
+					phy-handle = <&ephy5>;
+				};
+
+				cpu_port0: port@6 {
+					reg = <6>;
+					label = "cpu";
+					ethernet = <&gmac0>;
+					phy-mode = "rgmii";
+
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+						pause;
+					};
+				};
+			};
+		};
+	};
+};
--

2.20.1

#5 lore raw

Re: [PATCH net-next v2 2/3] dt-bindings: net: dsa: mt7530: Add support for port 5

Hi Rob,

<snip>

Quoted 15 lines
Quoted 6 lines
Quoted 6 lines

See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional required, optional properties and how the integrated switch subnodes must be specified.

(quoted diff) +0 -0
@@ -94,3 +130,185 @@ Example:
 			};
 		};
Quoted 8 lines

Documentation/devicetree/bindings/net/dsa/mt7530.txt Example: · line 137

Quoted 6 lines
Documentation/devicetree/bindings/net/dsa/mt7530.txt +5 -0
 	};
+
+Example 2: MT7621: Port 4 is WAN port: 2nd GMAC -> Port 5 -> PHY port 4.
+
+&eth {
+	status = "okay";

Don't show status in examples.

Quoted 5 lines

OK.

Quoted 2 lines

This should show the complete node.

I asked this question below in my previous email.
May be you missed it, I hope that you have time soon to answer this so that I can send a new version.

Quoted 1 line

To be clear, I should take ethernet node from the mt7621.dtsi [0] or mt7623.dtsi [1] and insert the example below?, right?

Greats,

René

Quoted 189 lines

Greats,

René

[0]: https://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next.git/tree/drivers/staging/mt7621-dts/mt7621.dtsi#n397
[1]: https://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next.git/tree/arch/arm/boot/dts/mt7623.dtsi#n1023

Quoted 181 lines
Quoted 181 lines
Documentation/devicetree/bindings/net/dsa/mt7530.txt +89 -0
+
+	gmac0: mac@0 {
+		compatible = "mediatek,eth-mac";
+		reg = <0>;
+		phy-mode = "rgmii";
+
+		fixed-link {
+			speed = <1000>;
+			full-duplex;
+			pause;
+		};
+	};
+
+	gmac1: mac@1 {
+		compatible = "mediatek,eth-mac";
+		reg = <1>;
+		phy-mode = "rgmii-txid";
+		phy-handle = <&phy4>;
+	};
+
+	mdio: mdio-bus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Internal phy */
+		phy4: ethernet-phy@4 {
+			reg = <4>;
+		};
+
+		mt7530: switch@1f {
+			compatible = "mediatek,mt7621";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1f>;
+			pinctrl-names = "default";
+			mediatek,mcm;
+
+			resets = <&rstctrl 2>;
+			reset-names = "mcm";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					label = "lan0";
+				};
+
+				port@1 {
+					reg = <1>;
+					label = "lan1";
+				};
+
+				port@2 {
+					reg = <2>;
+					label = "lan2";
+				};
+
+				port@3 {
+					reg = <3>;
+					label = "lan3";
+				};
+
+/* Commented out. Port 4 is handled by 2nd GMAC.
+				port@4 {
+					reg = <4>;
+					label = "lan4";
+				};
+*/
+
+				cpu_port0: port@6 {
+					reg = <6>;
+					label = "cpu";
+					ethernet = <&gmac0>;
+					phy-mode = "rgmii";
+
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+						pause;
+					};
+				};
+			};
+		};
+	};
+};
+
+Example 3: MT7621: Port 5 is connected to external PHY: Port 5 ->  

external PHY.

Documentation/devicetree/bindings/net/dsa/mt7530.txt +88 -1
+
+&eth {
+	status = "okay";
+
+	gmac0: mac@0 {
+		compatible = "mediatek,eth-mac";
+		reg = <0>;
+		phy-mode = "rgmii";
+
+		fixed-link {
+			speed = <1000>;
+			full-duplex;
+			pause;
+		};
+	};
+
+	mdio: mdio-bus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* External phy */
+		ephy5: ethernet-phy@7 {
+			reg = <7>;
+		};
+
+		mt7530: switch@1f {
+			compatible = "mediatek,mt7621";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1f>;
+			pinctrl-names = "default";
+			mediatek,mcm;
+
+			resets = <&rstctrl 2>;
+			reset-names = "mcm";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					label = "lan0";
+				};
+
+				port@1 {
+					reg = <1>;
+					label = "lan1";
+				};
+
+				port@2 {
+					reg = <2>;
+					label = "lan2";
+				};
+
+				port@3 {
+					reg = <3>;
+					label = "lan3";
+				};
+
+				port@4 {
+					reg = <4>;
+					label = "lan4";
+				};
+
+				port@5 {
+					reg = <5>;
+					label = "lan5";
+					phy-mode = "rgmii";
+					phy-handle = <&ephy5>;
+				};
+
+				cpu_port0: port@6 {
+					reg = <6>;
+					label = "cpu";
+					ethernet = <&gmac0>;
+					phy-mode = "rgmii";
+
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+						pause;
+					};
+				};
+			};
+		};
+	};
+};
--

2.20.1