Skip to contentSkip to conversation

Revert "drm/bridge: adv7511: Attach to DSI host at probe time"

PATCH Applied Rob Clark 2 participants 2 messages Aug 29, 2019 – Sep 13, 2019

Subsystems (3)
lore
Share & tools
lore

Rob Clark

author
#0 lore raw

PATCH 1/1 Revert "drm/bridge: adv7511: Attach to DSI host at probe time"

From: Rob Clark <[email protected]>

This reverts commit 83f35bc3a852f1c3892c7474998c5cec707c7ba3.

This commit the wrong direction, we should really be changing panel framework to attach dsi host after probe, rather than introducing the same probe-order problem that panels already have to bridges.

The reason is, that in order to deal with devices where display is enabled by bootloader and efifb/simplefb is used until the real driver probes, we need to be careful to not touch the hardware until we have all the pieces probed and ready to go, otherwise you will kill the working display, leaving yourself (at least, in the case of real consumer devices that do not have a debug UART) with no good way to debug what went wrong.

---
 drivers/gpu/drm/bridge/adv7511/adv7511_drv.c | 12 +++---------
 1 file changed, 3 insertions(+), 9 deletions(-)
drivers/gpu/drm/bridge/adv7511/adv7511_drv.c +3 -9
index 98bccace8c1c..f6d2681f6927 100644
@@ -874,6 +874,9 @@ static int adv7511_bridge_attach(struct drm_bridge *bridge)
 				 &adv7511_connector_helper_funcs);
 	drm_connector_attach_encoder(&adv->connector, bridge->encoder);
 
+	if (adv->type == ADV7533)
+		ret = adv7533_attach_dsi(adv);
+
 	if (adv->i2c_main->irq)
 		regmap_write(adv->regmap, ADV7511_REG_INT_ENABLE(0),
 			     ADV7511_INT0_HPD);
@@ -1219,17 +1222,8 @@ static int adv7511_probe(struct i2c_client *i2c, const struct i2c_device_id *id)
 	drm_bridge_add(&adv7511->bridge);
 
 	adv7511_audio_init(dev, adv7511);
-
-	if (adv7511->type == ADV7533) {
-		ret = adv7533_attach_dsi(adv7511);
-		if (ret)
-			goto err_remove_bridge;
-	}
-
 	return 0;
 
-err_remove_bridge:
-	drm_bridge_remove(&adv7511->bridge);
 err_unregister_cec:
 	i2c_unregister_device(adv7511->i2c_cec);
 	if (adv7511->cec_clk)
Signature · 1 line
2.21.0
#1 lore raw
Quoted 16 lines · Rob Clark

From: Rob Clark <[email protected]>

This reverts commit 83f35bc3a852f1c3892c7474998c5cec707c7ba3.

This commit the wrong direction, we should really be changing panel framework to attach dsi host after probe, rather than introducing the same probe-order problem that panels already have to bridges.

The reason is, that in order to deal with devices where display is enabled by bootloader and efifb/simplefb is used until the real driver probes, we need to be careful to not touch the hardware until we have all the pieces probed and ready to go, otherwise you will kill the working display, leaving yourself (at least, in the case of real consumer devices that do not have a debug UART) with no good way to debug what went wrong.

Quoted 1 line

Applied to drm-misc-next-fixes, with changed commit message - I hope it is OK for you.

Regards

Andrzej

Quoted 36 lines
---
 drivers/gpu/drm/bridge/adv7511/adv7511_drv.c | 12 +++---------
 1 file changed, 3 insertions(+), 9 deletions(-)
drivers/gpu/drm/bridge/adv7511/adv7511_drv.c +3 -9
index 98bccace8c1c..f6d2681f6927 100644
@@ -874,6 +874,9 @@ static int adv7511_bridge_attach(struct drm_bridge *bridge)
 				 &adv7511_connector_helper_funcs);
 	drm_connector_attach_encoder(&adv->connector, bridge->encoder);
 
+	if (adv->type == ADV7533)
+		ret = adv7533_attach_dsi(adv);
+
 	if (adv->i2c_main->irq)
 		regmap_write(adv->regmap, ADV7511_REG_INT_ENABLE(0),
 			     ADV7511_INT0_HPD);
@@ -1219,17 +1222,8 @@ static int adv7511_probe(struct i2c_client *i2c, const struct i2c_device_id *id)
 	drm_bridge_add(&adv7511->bridge);
 
 	adv7511_audio_init(dev, adv7511);
-
-	if (adv7511->type == ADV7533) {
-		ret = adv7533_attach_dsi(adv7511);
-		if (ret)
-			goto err_remove_bridge;
-	}
-
 	return 0;
 
-err_remove_bridge:
-	drm_bridge_remove(&adv7511->bridge);
 err_unregister_cec:
 	i2c_unregister_device(adv7511->i2c_cec);
 	if (adv7511->cec_clk)