dt-bindings: rng: exynos4-rng: Convert Exynos PRNG bindings to json-schema
Subsystems (30)
Krzysztof Kozlowski
maintainerPATCH v2 1/8 dt-bindings: rng: exynos4-rng: Convert Exynos PRNG bindings to json-schema
Convert Samsung Exynos Pseudo Random Number Generator bindings to DT schema format using json-schema.
---
Changes since v1:
1. Indent example with four spaces (more readable).
--- .../bindings/rng/samsung,exynos4-rng.txt | 19 --------- .../bindings/rng/samsung,exynos4-rng.yaml | 41 +++++++++++++++++++ MAINTAINERS | 2 +- 3 files changed, 42 insertions(+), 20 deletions(-) delete mode 100644 Documentation/devicetree/bindings/rng/samsung,exynos4-rng.txt create mode 100644 Documentation/devicetree/bindings/rng/samsung,exynos4-rng.yaml
Documentation/devicetree/bindings/rng/samsung,exynos4-rng.txt deleted +0 -19
@@ -1,19 +0,0 @@ -Exynos Pseudo Random Number Generator - -Required properties: - -- compatible : One of: - - "samsung,exynos4-rng" for Exynos4210 and Exynos4412 - - "samsung,exynos5250-prng" for Exynos5250+ -- reg : Specifies base physical address and size of the registers map. -- clocks : Phandle to clock-controller plus clock-specifier pair. -- clock-names : "secss" as a clock name. - -Example: - - rng@10830400 { - compatible = "samsung,exynos4-rng"; - reg = <0x10830400 0x200>; - clocks = <&clock CLK_SSS>; - clock-names = "secss"; - };
Documentation/devicetree/bindings/rng/samsung,exynos4-rng.yaml new file +41 -0
41 lines not on this page · raw message
MAINTAINERS +1 -1
@@ -14181,7 +14181,7 @@ L: [email protected] L: [email protected] S: Maintained F: drivers/crypto/exynos-rng.c -F: Documentation/devicetree/bindings/rng/samsung,exynos4-rng.txt +F: Documentation/devicetree/bindings/rng/samsung,exynos4-rng.yaml SAMSUNG EXYNOS TRUE RANDOM NUMBER GENERATOR (TRNG) DRIVER M: Łukasz Stelmach <[email protected]>
Signature · 1 line
2.17.1
Krzysztof Kozlowski
maintainerPATCH v2 2/8 dt-bindings: sram: Convert SRAM bindings to json-schema
Convert generic mmio-sram bindings to DT schema format using json-schema.
---
Changes since v1:
1. Indent example with four spaces (more readable).
--- .../devicetree/bindings/sram/sram.txt | 80 ---------- .../devicetree/bindings/sram/sram.yaml | 138 ++++++++++++++++++ 2 files changed, 138 insertions(+), 80 deletions(-) delete mode 100644 Documentation/devicetree/bindings/sram/sram.txt create mode 100644 Documentation/devicetree/bindings/sram/sram.yaml
Documentation/devicetree/bindings/sram/sram.txt deleted +0 -80
@@ -1,80 +0,0 @@ -Generic on-chip SRAM - -Simple IO memory regions to be managed by the genalloc API. - -Required properties: - -- compatible : mmio-sram or atmel,sama5d2-securam - -- reg : SRAM iomem address range - -Reserving sram areas: ---------------------- - -Each child of the sram node specifies a region of reserved memory. Each -child node should use a 'reg' property to specify a specific range of -reserved memory. - -Following the generic-names recommended practice, node names should -reflect the purpose of the node. Unit address (@<address>) should be -appended to the name. - -Required properties in the sram node: - -- #address-cells, #size-cells : should use the same values as the root node -- ranges : standard definition, should translate from local addresses - within the sram to bus addresses - -Optional properties in the sram node: - -- no-memory-wc : the flag indicating, that SRAM memory region has not to - be remapped as write combining. WC is used by default. - -Required properties in the area nodes: - -- reg : iomem address range, relative to the SRAM range - -Optional properties in the area nodes: - -- compatible : standard definition, should contain a vendor specific string - in the form <vendor>,[<device>-]<usage> -- pool : indicates that the particular reserved SRAM area is addressable - and in use by another device or devices -- export : indicates that the reserved SRAM area may be accessed outside - of the kernel, e.g. by bootloader or userspace -- protect-exec : Same as 'pool' above but with the additional - constraint that code wil be run from the region and - that the memory is maintained as read-only, executable - during code execution. NOTE: This region must be page - aligned on start and end in order to properly allow - manipulation of the page attributes. -- label : the name for the reserved partition, if omitted, the label - is taken from the node name excluding the unit address. -- clocks : a list of phandle and clock specifier pair that controls the - single SRAM clock. - -Example: - -sram: sram@5c000000 { - compatible = "mmio-sram"; - reg = <0x5c000000 0x40000>; /* 256 KiB SRAM at address 0x5c000000 */ - - #address-cells = <1>; - #size-cells = <1>; - ranges = <0 0x5c000000 0x40000>; - - smp-sram@100 { - compatible = "socvendor,smp-sram"; - reg = <0x100 0x50>; - }; - - device-sram@1000 { - reg = <0x1000 0x1000>; - pool; - }; - - exported@20000 { - reg = <0x20000 0x20000>; - export; - }; -};
Documentation/devicetree/bindings/sram/sram.yaml new file +138 -0
138 lines not on this page · raw message
Signature · 6 lines
2.17.1 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Krzysztof Kozlowski
maintainerPATCH v2 3/8 dt-bindings: sram: Convert Samsung Exynos SYSRAM bindings to json-schema
In reply to Krzysztof KozlowskiConvert Samsung Exynos SYSRAM bindings to DT schema format using json-schema.
---
TODO:
The node naming should be probably fixed (sysram->sram)
Changes since v1:
1. Indent example with four spaces (more readable).
--- .../devicetree/bindings/sram/samsung-sram.txt | 38 ------------ .../bindings/sram/samsung-sram.yaml | 58 +++++++++++++++++++ MAINTAINERS | 2 +- 3 files changed, 59 insertions(+), 39 deletions(-) delete mode 100644 Documentation/devicetree/bindings/sram/samsung-sram.txt create mode 100644 Documentation/devicetree/bindings/sram/samsung-sram.yaml
Documentation/devicetree/bindings/sram/samsung-sram.txt deleted +0 -38
@@ -1,38 +0,0 @@ -Samsung Exynos SYSRAM for SMP bringup: ------------------------------------- - -Samsung SMP-capable Exynos SoCs use part of the SYSRAM for the bringup -of the secondary cores. Once the core gets powered up it executes the -code that is residing at some specific location of the SYSRAM. - -Therefore reserved section sub-nodes have to be added to the mmio-sram -declaration. These nodes are of two types depending upon secure or -non-secure execution environment. - -Required sub-node properties: -- compatible : depending upon boot mode, should be - "samsung,exynos4210-sysram" : for Secure SYSRAM - "samsung,exynos4210-sysram-ns" : for Non-secure SYSRAM - -The rest of the properties should follow the generic mmio-sram discription -found in Documentation/devicetree/bindings/sram/sram.txt - -Example: - - sysram@2020000 { - compatible = "mmio-sram"; - reg = <0x02020000 0x54000>; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0 0x02020000 0x54000>; - - smp-sysram@0 { - compatible = "samsung,exynos4210-sysram"; - reg = <0x0 0x1000>; - }; - - smp-sysram@53000 { - compatible = "samsung,exynos4210-sysram-ns"; - reg = <0x53000 0x1000>; - }; - };
Documentation/devicetree/bindings/sram/samsung-sram.yaml new file +58 -0
58 lines not on this page · raw message
MAINTAINERS +1 -1
@@ -2225,7 +2225,7 @@ F: drivers/soc/samsung/ F: include/linux/soc/samsung/ F: Documentation/arm/samsung/ F: Documentation/devicetree/bindings/arm/samsung/ -F: Documentation/devicetree/bindings/sram/samsung-sram.txt +F: Documentation/devicetree/bindings/sram/samsung-sram.yaml F: Documentation/devicetree/bindings/power/pd-samsung.txt N: exynos
Signature · 1 line
2.17.1
Krzysztof Kozlowski
maintainerPATCH v2 4/8 dt-bindings: memory-controllers: Convert Samsung Exynos SROM bindings to json-schema
In reply to Krzysztof KozlowskiConvert Samsung Exynos SROM controller bindings to DT schema format using json-schema.
---
Changes since v1:
1. Indent example with four spaces (more readable),
2. Split examples into two,
3. Fix pattern for subnode name,
4. Remove checks for #address-cells-ranges-#size-cells,
5. Add "additionalProperties" so the wrongly named subnodes would be matched.
--- .../memory-controllers/exynos-srom.txt | 79 ----------- .../memory-controllers/exynos-srom.yaml | 128 ++++++++++++++++++ 2 files changed, 128 insertions(+), 79 deletions(-) delete mode 100644 Documentation/devicetree/bindings/memory-controllers/exynos-srom.txt create mode 100644 Documentation/devicetree/bindings/memory-controllers/exynos-srom.yaml
Documentation/devicetree/bindings/memory-controllers/exynos-srom.txt deleted +0 -79
@@ -1,79 +0,0 @@ -SAMSUNG Exynos SoCs SROM Controller driver. - -Required properties: -- compatible : Should contain "samsung,exynos4210-srom". - -- reg: offset and length of the register set - -Optional properties: -The SROM controller can be used to attach external peripherals. In this case -extra properties, describing the bus behind it, should be specified as below: - -- #address-cells: Must be set to 2 to allow device address translation. - Address is specified as (bank#, offset). - -- #size-cells: Must be set to 1 to allow device size passing - -- ranges: Must be set up to reflect the memory layout with four integer values - per bank: - <bank-number> 0 <parent address of bank> <size> - -Sub-nodes: -The actual device nodes should be added as subnodes to the SROMc node. These -subnodes, in addition to regular device specification, should contain the following -properties, describing configuration of the relevant SROM bank: - -Required properties: -- reg: bank number, base address (relative to start of the bank) and size of - the memory mapped for the device. Note that base address will be - typically 0 as this is the start of the bank. - -- samsung,srom-timing : array of 6 integers, specifying bank timings in the - following order: Tacp, Tcah, Tcoh, Tacc, Tcos, Tacs. - Each value is specified in cycles and has the following - meaning and valid range: - Tacp : Page mode access cycle at Page mode (0 - 15) - Tcah : Address holding time after CSn (0 - 15) - Tcoh : Chip selection hold on OEn (0 - 15) - Tacc : Access cycle (0 - 31, the actual time is N + 1) - Tcos : Chip selection set-up before OEn (0 - 15) - Tacs : Address set-up before CSn (0 - 15) - -Optional properties: -- reg-io-width : data width in bytes (1 or 2). If omitted, default of 1 is used. - -- samsung,srom-page-mode : if page mode is set, 4 data page mode will be configured, - else normal (1 data) page mode will be set. - -Example: basic definition, no banks are configured - memory-controller@12570000 { - compatible = "samsung,exynos4210-srom"; - reg = <0x12570000 0x14>; - }; - -Example: SROMc with SMSC911x ethernet chip on bank 3 - memory-controller@12570000 { - #address-cells = <2>; - #size-cells = <1>; - ranges = <0 0 0x04000000 0x20000 // Bank0 - 1 0 0x05000000 0x20000 // Bank1 - 2 0 0x06000000 0x20000 // Bank2 - 3 0 0x07000000 0x20000>; // Bank3 - - compatible = "samsung,exynos4210-srom"; - reg = <0x12570000 0x14>; - - ethernet@3,0 { - compatible = "smsc,lan9115"; - reg = <3 0 0x10000>; // Bank 3, offset = 0 - phy-mode = "mii"; - interrupt-parent = <&gpx0>; - interrupts = <5 8>; - reg-io-width = <2>; - smsc,irq-push-pull; - smsc,force-internal-phy; - - samsung,srom-page-mode; - samsung,srom-timing = <9 12 1 9 1 1>; - }; - };
Documentation/devicetree/bindings/memory-controllers/exynos-srom.yaml new file +128 -0
128 lines not on this page · raw message
Signature · 6 lines
2.17.1 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Krzysztof Kozlowski
maintainerPATCH v2 5/8 dt-bindings: watchdog: Convert Samsung SoC watchdog bindings to json-schema
In reply to Krzysztof KozlowskiConvert Samsung S3C/S5P/Exynos watchdog bindings to DT schema format using json-schema.
---
Changes since v1:
1. Indent example with four spaces (more readable),
2. Remove unneeded timeout-sec description.
--- .../bindings/watchdog/samsung-wdt.txt | 35 ---------- .../bindings/watchdog/samsung-wdt.yaml | 67 +++++++++++++++++++ 2 files changed, 67 insertions(+), 35 deletions(-) delete mode 100644 Documentation/devicetree/bindings/watchdog/samsung-wdt.txt create mode 100644 Documentation/devicetree/bindings/watchdog/samsung-wdt.yaml
Documentation/devicetree/bindings/watchdog/samsung-wdt.txt deleted +0 -35
@@ -1,35 +0,0 @@ -* Samsung's Watchdog Timer Controller - -The Samsung's Watchdog controller is used for resuming system operation -after a preset amount of time during which the WDT reset event has not -occurred. - -Required properties: -- compatible : should be one among the following - - "samsung,s3c2410-wdt" for S3C2410 - - "samsung,s3c6410-wdt" for S3C6410, S5PV210 and Exynos4 - - "samsung,exynos5250-wdt" for Exynos5250 - - "samsung,exynos5420-wdt" for Exynos5420 - - "samsung,exynos7-wdt" for Exynos7 - -- reg : base physical address of the controller and length of memory mapped - region. -- interrupts : interrupt number to the cpu. -- samsung,syscon-phandle : reference to syscon node (This property required only - in case of compatible being "samsung,exynos5250-wdt" or "samsung,exynos5420-wdt". - In case of Exynos5250 and 5420 this property points to syscon node holding the PMU - base address) - -Optional properties: -- timeout-sec : contains the watchdog timeout in seconds. - -Example: - -watchdog@101d0000 { - compatible = "samsung,exynos5250-wdt"; - reg = <0x101D0000 0x100>; - interrupts = <0 42 0>; - clocks = <&clock 336>; - clock-names = "watchdog"; - samsung,syscon-phandle = <&pmu_syscon>; -};
Documentation/devicetree/bindings/watchdog/samsung-wdt.yaml new file +67 -0
67 lines not on this page · raw message
Signature · 6 lines
2.17.1 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Krzysztof Kozlowski
maintainerPATCH v2 6/8 dt-bindings: watchdog: Add missing clocks requirement in Samsung SoC watchdog
In reply to Krzysztof KozlowskiThe Samsung SoC watchdog driver always required providing a clock (either through platform data or from DT). However when bindings were added in commit 9487a9cc7140 ("watchdog: s3c2410: Add support for device tree based probe"), they missed the requirement of clock.
---
Changes since v1:
1. Indent example with four spaces (more readable),
2. Add also missing required entries for clocks.
--- .../devicetree/bindings/watchdog/samsung-wdt.yaml | 9 +++++++++ 1 file changed, 9 insertions(+)
Documentation/devicetree/bindings/watchdog/samsung-wdt.yaml +9 -0
@@ -26,6 +26,13 @@ properties: reg: maxItems: 1 + clocks: + maxItems: 1 + + clock-names: + items: + - const: watchdog + interrupts: maxItems: 1
@@ -40,6 +47,8 @@ properties: required: - compatible + - clocks + - clock-names - interrupts - reg
Signature · 6 lines
2.17.1 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Krzysztof Kozlowski
maintainerPATCH v2 7/8 dt-bindings: pwm: Convert PWM bindings to json-schema
In reply to Krzysztof KozlowskiConvert generic PWM bindings to DT schema format using json-schema. The consumer bindings are split to separate file.
---
Changes since v1:
1. Indent example with four spaces (more readable),
2. Change pattern for pwm nodes,
3. Remove $ref from #cells.
--- .../devicetree/bindings/clock/pwm-clock.txt | 2 +- .../bindings/display/bridge/ti,sn65dsi86.txt | 2 +- .../devicetree/bindings/display/ssd1307fb.txt | 2 +- .../bindings/leds/backlight/pwm-backlight.txt | 2 +- .../devicetree/bindings/leds/leds-pwm.txt | 2 +- .../devicetree/bindings/mfd/max77693.txt | 2 +- .../bindings/pwm/atmel-hlcdc-pwm.txt | 2 +- .../devicetree/bindings/pwm/atmel-pwm.txt | 2 +- .../devicetree/bindings/pwm/atmel-tcb-pwm.txt | 2 +- .../bindings/pwm/brcm,bcm7038-pwm.txt | 2 +- .../bindings/pwm/brcm,iproc-pwm.txt | 2 +- .../devicetree/bindings/pwm/brcm,kona-pwm.txt | 2 +- .../devicetree/bindings/pwm/img-pwm.txt | 2 +- .../devicetree/bindings/pwm/imx-pwm.txt | 2 +- .../devicetree/bindings/pwm/imx-tpm-pwm.txt | 2 +- .../bindings/pwm/lpc1850-sct-pwm.txt | 2 +- .../devicetree/bindings/pwm/mxs-pwm.txt | 2 +- .../bindings/pwm/nvidia,tegra20-pwm.txt | 2 +- .../bindings/pwm/nxp,pca9685-pwm.txt | 2 +- .../devicetree/bindings/pwm/pwm-bcm2835.txt | 2 +- .../devicetree/bindings/pwm/pwm-berlin.txt | 2 +- .../bindings/pwm/pwm-consumers.yaml | 76 +++++++++++++++++++ .../devicetree/bindings/pwm/pwm-fsl-ftm.txt | 2 +- .../devicetree/bindings/pwm/pwm-hibvt.txt | 2 +- .../devicetree/bindings/pwm/pwm-lp3943.txt | 2 +- .../devicetree/bindings/pwm/pwm-mediatek.txt | 2 +- .../devicetree/bindings/pwm/pwm-meson.txt | 2 +- .../devicetree/bindings/pwm/pwm-mtk-disp.txt | 2 +- .../bindings/pwm/pwm-omap-dmtimer.txt | 2 +- .../devicetree/bindings/pwm/pwm-rockchip.txt | 2 +- .../devicetree/bindings/pwm/pwm-sifive.txt | 2 +- .../devicetree/bindings/pwm/pwm-stm32-lp.txt | 2 +- .../devicetree/bindings/pwm/pwm-stm32.txt | 2 +- .../devicetree/bindings/pwm/pwm-tiecap.txt | 2 +- .../devicetree/bindings/pwm/pwm-tiehrpwm.txt | 2 +- .../devicetree/bindings/pwm/pwm-zx.txt | 2 +- Documentation/devicetree/bindings/pwm/pwm.txt | 69 ----------------- .../devicetree/bindings/pwm/pwm.yaml | 29 +++++++ .../bindings/pwm/renesas,pwm-rcar.txt | 2 +- .../bindings/pwm/renesas,tpu-pwm.txt | 4 +- .../devicetree/bindings/pwm/spear-pwm.txt | 2 +- .../devicetree/bindings/pwm/st,stmpe-pwm.txt | 2 +- .../devicetree/bindings/pwm/ti,twl-pwm.txt | 2 +- .../devicetree/bindings/pwm/ti,twl-pwmled.txt | 2 +- .../devicetree/bindings/pwm/vt8500-pwm.txt | 2 +- .../bindings/regulator/pwm-regulator.txt | 2 +- .../devicetree/bindings/timer/ingenic,tcu.txt | 2 +- 47 files changed, 150 insertions(+), 114 deletions(-) create mode 100644 Documentation/devicetree/bindings/pwm/pwm-consumers.yaml delete mode 100644 Documentation/devicetree/bindings/pwm/pwm.txt create mode 100644 Documentation/devicetree/bindings/pwm/pwm.yaml
Documentation/devicetree/bindings/clock/pwm-clock.txt +1 -1
@@ -3,7 +3,7 @@ Binding for an external clock signal driven by a PWM pin. This binding uses the common clock binding[1] and the common PWM binding[2]. [1] Documentation/devicetree/bindings/clock/clock-bindings.txt -[2] Documentation/devicetree/bindings/pwm/pwm.txt +[2] Documentation/devicetree/bindings/pwm/pwm-consumers.yaml Required properties: - compatible : shall be "pwm-clock".
Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt +1 -1
@@ -21,7 +21,7 @@ Optional properties: - #gpio-cells : Should be two. The first cell is the pin number and the second cell is used to specify flags. See ../../gpio/gpio.txt for more information. -- #pwm-cells : Should be one. See ../../pwm/pwm.txt for description of +- #pwm-cells : Should be one. See ../../pwm/pwm.yaml for description of the cell formats. - clock-names: should be "refclk"
Documentation/devicetree/bindings/display/ssd1307fb.txt +1 -1
@@ -37,7 +37,7 @@ Optional properties: - solomon,area-color-enable: Display uses color mode - solomon,low-power. Display runs in low power mode -[0]: Documentation/devicetree/bindings/pwm/pwm.txt +[0]: Documentation/devicetree/bindings/pwm/pwm-consumers.yaml Examples: ssd1307: oled@3c {
Documentation/devicetree/bindings/leds/backlight/pwm-backlight.txt +1 -1
@@ -28,7 +28,7 @@ Optional properties: having to list out every possible value in the brightness-level array. -[0]: Documentation/devicetree/bindings/pwm/pwm.txt +[0]: Documentation/devicetree/bindings/pwm/pwm-consumers.yaml [1]: Documentation/devicetree/bindings/gpio/gpio.txt Example:
Documentation/devicetree/bindings/leds/leds-pwm.txt +1 -1
@@ -11,7 +11,7 @@ LED sub-node properties: specify the period time to be used: <&phandle id period_ns>; - pwm-names : (optional) Name to be used by the PWM subsystem for the PWM device For the pwms and pwm-names property please refer to: - Documentation/devicetree/bindings/pwm/pwm.txt + Documentation/devicetree/bindings/pwm/pwm-consumers.yaml - max-brightness : Maximum brightness possible for the LED - active-low : (optional) For PWMs where the LED is wired to supply rather than ground.
Documentation/devicetree/bindings/mfd/max77693.txt +1 -1
@@ -38,7 +38,7 @@ Optional properties: PWM properties should be named "pwms". And number of cell is different for each pwm device. To get more information, please refer to documentation. - [*] refer Documentation/devicetree/bindings/pwm/pwm.txt + [*] refer Documentation/devicetree/bindings/pwm/pwm-consumers.yaml - charger : Node configuring the charger driver. If present, required properties:
Documentation/devicetree/bindings/pwm/atmel-hlcdc-pwm.txt +1 -1
@@ -10,7 +10,7 @@ Required properties: - pinctrl-0: should contain the pinctrl states described by pinctrl default. - #pwm-cells: should be set to 3. This PWM chip use the default 3 cells - bindings defined in pwm.txt in this directory. + bindings defined in pwm.yaml in this directory. Example:
Documentation/devicetree/bindings/pwm/atmel-pwm.txt +1 -1
@@ -7,7 +7,7 @@ Required properties: - "atmel,sama5d2-pwm" - "microchip,sam9x60-pwm" - reg: physical base address and length of the controller's registers - - #pwm-cells: Should be 3. See pwm.txt in this directory for a + - #pwm-cells: Should be 3. See pwm.yaml in this directory for a description of the cells format. Example:
Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt +1 -1
@@ -2,7 +2,7 @@ Atmel TCB PWM controller Required properties: - compatible: should be "atmel,tcb-pwm" -- #pwm-cells: should be 3. See pwm.txt in this directory for a description of +- #pwm-cells: should be 3. See pwm.yaml in this directory for a description of the cells format. The only third cell flag supported by this binding is PWM_POLARITY_INVERTED. - tc-block: The Timer Counter block to use as a PWM chip.
Documentation/devicetree/bindings/pwm/brcm,bcm7038-pwm.txt +1 -1
@@ -4,7 +4,7 @@ Required properties: - compatible: must be "brcm,bcm7038-pwm" - reg: physical base address and length for this controller -- #pwm-cells: should be 2. See pwm.txt in this directory for a description +- #pwm-cells: should be 2. See pwm.yaml in this directory for a description of the cells format - clocks: a phandle to the reference clock for this block which is fed through its internal variable clock frequency generator
Documentation/devicetree/bindings/pwm/brcm,iproc-pwm.txt +1 -1
@@ -6,7 +6,7 @@ Required Properties : - compatible: must be "brcm,iproc-pwm" - reg: physical base address and length of the controller's registers - clocks: phandle + clock specifier pair for the external clock -- #pwm-cells: Should be 3. See pwm.txt in this directory for a +- #pwm-cells: Should be 3. See pwm.yaml in this directory for a description of the cells format. Refer to clocks/clock-bindings.txt for generic clock consumer properties.
Documentation/devicetree/bindings/pwm/brcm,kona-pwm.txt +1 -1
@@ -6,7 +6,7 @@ Required Properties : - compatible: should contain "brcm,kona-pwm" - reg: physical base address and length of the controller's registers - clocks: phandle + clock specifier pair for the external clock -- #pwm-cells: Should be 3. See pwm.txt in this directory for a +- #pwm-cells: Should be 3. See pwm.yaml in this directory for a description of the cells format. Refer to clocks/clock-bindings.txt for generic clock consumer properties.
Documentation/devicetree/bindings/pwm/img-pwm.txt +1 -1
@@ -8,7 +8,7 @@ Required properties: - clock-names: Must include the following entries. - pwm: PWM operating clock. - sys: PWM system interface clock. - - #pwm-cells: Should be 2. See pwm.txt in this directory for the + - #pwm-cells: Should be 2. See pwm.yaml in this directory for the description of the cells format. - img,cr-periph: Must contain a phandle to the peripheral control syscon node which contains PWM control registers.
Documentation/devicetree/bindings/pwm/imx-pwm.txt +1 -1
@@ -6,7 +6,7 @@ Required properties: - "fsl,imx1-pwm" for PWM compatible with the one integrated on i.MX1 - "fsl,imx27-pwm" for PWM compatible with the one integrated on i.MX27 - reg: physical base address and length of the controller's registers -- #pwm-cells: 2 for i.MX1 and 3 for i.MX27 and newer SoCs. See pwm.txt +- #pwm-cells: 2 for i.MX1 and 3 for i.MX27 and newer SoCs. See pwm.yaml in this directory for a description of the cells format. - clocks : Clock specifiers for both ipg and per clocks. - clock-names : Clock names should include both "ipg" and "per"
Documentation/devicetree/bindings/pwm/imx-tpm-pwm.txt +1 -1
@@ -3,7 +3,7 @@ Freescale i.MX TPM PWM controller Required properties: - compatible : Should be "fsl,imx7ulp-pwm". - reg: Physical base address and length of the controller's registers. -- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of the cells format. +- #pwm-cells: Should be 3. See pwm.yaml in this directory for a description of the cells format. - clocks : The clock provided by the SoC to drive the PWM. - interrupts: The interrupt for the PWM controller.
Documentation/devicetree/bindings/pwm/lpc1850-sct-pwm.txt +1 -1
@@ -7,7 +7,7 @@ Required properties: See ../clock/clock-bindings.txt for details. - clock-names: Must include the following entries. - pwm: PWM operating clock. - - #pwm-cells: Should be 3. See pwm.txt in this directory for the description + - #pwm-cells: Should be 3. See pwm.yaml in this directory for the description of the cells format. Example:
Documentation/devicetree/bindings/pwm/mxs-pwm.txt +1 -1
@@ -3,7 +3,7 @@ Freescale MXS PWM controller Required properties: - compatible: should be "fsl,imx23-pwm" - reg: physical base address and length of the controller's registers -- #pwm-cells: should be 2. See pwm.txt in this directory for a description of +- #pwm-cells: should be 2. See pwm.yaml in this directory for a description of the cells format. - fsl,pwm-number: the number of PWM devices
Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt +1 -1
@@ -10,7 +10,7 @@ Required properties: - "nvidia,tegra210-pwm", "nvidia,tegra20-pwm": for Tegra210 - "nvidia,tegra186-pwm": for Tegra186 - reg: physical base address and length of the controller's registers -- #pwm-cells: should be 2. See pwm.txt in this directory for a description of +- #pwm-cells: should be 2. See pwm.yaml in this directory for a description of the cells format. - clocks: Must contain one entry, for the module clock. See ../clocks/clock-bindings.txt for details.
Documentation/devicetree/bindings/pwm/nxp,pca9685-pwm.txt +1 -1
@@ -3,7 +3,7 @@ NXP PCA9685 16-channel 12-bit PWM LED controller Required properties: - compatible: "nxp,pca9685-pwm" - - #pwm-cells: Should be 2. See pwm.txt in this directory for a description of + - #pwm-cells: Should be 2. See pwm.yaml in this directory for a description of the cells format. The index 16 is the ALLCALL channel, that sets all PWM channels at the same time.
Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt +1 -1
@@ -6,7 +6,7 @@ Required properties: - clocks: This clock defines the base clock frequency of the PWM hardware system, the period and the duty_cycle of the PWM signal is a multiple of the base period. -- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of +- #pwm-cells: Should be 3. See pwm.yaml in this directory for a description of the cells format. Examples:
Documentation/devicetree/bindings/pwm/pwm-berlin.txt +1 -1
@@ -4,7 +4,7 @@ Required properties: - compatible: should be "marvell,berlin-pwm" - reg: physical base address and length of the controller's registers - clocks: phandle to the input clock -- #pwm-cells: should be 3. See pwm.txt in this directory for a description of +- #pwm-cells: should be 3. See pwm.yaml in this directory for a description of the cells format. Example:
Documentation/devicetree/bindings/pwm/pwm-consumers.yaml new file +76 -0
76 lines not on this page · raw message
Documentation/devicetree/bindings/pwm/pwm-fsl-ftm.txt +1 -1
@@ -21,7 +21,7 @@ Required properties: - "fsl,vf610-ftm-pwm" for PWM compatible with the one integrated on VF610 - "fsl,imx8qm-ftm-pwm" for PWM compatible with the one integrated on i.MX8QM - reg: Physical base address and length of the controller's registers -- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of +- #pwm-cells: Should be 3. See pwm.yaml in this directory for a description of the cells format. - clock-names: Should include the following module clock source entries: "ftm_sys" (module clock, also can be used as counter clock),
Documentation/devicetree/bindings/pwm/pwm-hibvt.txt +1 -1
@@ -10,7 +10,7 @@ Required properties: - reg: physical base address and length of the controller's registers. - clocks: phandle and clock specifier of the PWM reference clock. - resets: phandle and reset specifier for the PWM controller reset. -- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of +- #pwm-cells: Should be 3. See pwm.yaml in this directory for a description of the cells format. Example:
Documentation/devicetree/bindings/pwm/pwm-lp3943.txt +1 -1
@@ -2,7 +2,7 @@ TI/National Semiconductor LP3943 PWM controller Required properties: - compatible: "ti,lp3943-pwm" - - #pwm-cells: Should be 2. See pwm.txt in this directory for a + - #pwm-cells: Should be 2. See pwm.yaml in this directory for a description of the cells format. Note that this hardware limits the period length to the range 6250~1600000.
Documentation/devicetree/bindings/pwm/pwm-mediatek.txt +1 -1
@@ -7,7 +7,7 @@ Required properties: - "mediatek,mt7623-pwm": found on mt7623 SoC. - "mediatek,mt7628-pwm": found on mt7628 SoC. - reg: physical base address and length of the controller's registers. - - #pwm-cells: must be 2. See pwm.txt in this directory for a description of + - #pwm-cells: must be 2. See pwm.yaml in this directory for a description of the cell format. - clocks: phandle and clock specifier of the PWM reference clock. - clock-names: must contain the following, except for MT7628 which
Documentation/devicetree/bindings/pwm/pwm-meson.txt +1 -1
@@ -10,7 +10,7 @@ Required properties: or "amlogic,meson-g12a-ee-pwm" or "amlogic,meson-g12a-ao-pwm-ab" or "amlogic,meson-g12a-ao-pwm-cd" -- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of +- #pwm-cells: Should be 3. See pwm.yaml in this directory for a description of the cells format. Optional properties:
Documentation/devicetree/bindings/pwm/pwm-mtk-disp.txt +1 -1
@@ -6,7 +6,7 @@ Required properties: - "mediatek,mt6595-disp-pwm": found on mt6595 SoC. - "mediatek,mt8173-disp-pwm": found on mt8173 SoC. - reg: physical base address and length of the controller's registers. - - #pwm-cells: must be 2. See pwm.txt in this directory for a description of + - #pwm-cells: must be 2. See pwm.yaml in this directory for a description of the cell format. - clocks: phandle and clock specifier of the PWM reference clock. - clock-names: must contain the following:
Documentation/devicetree/bindings/pwm/pwm-omap-dmtimer.txt +1 -1
@@ -4,7 +4,7 @@ Required properties: - compatible: Shall contain "ti,omap-dmtimer-pwm". - ti,timers: phandle to PWM capable OMAP timer. See timer/ti,timer.txt for info about these timers. -- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of +- #pwm-cells: Should be 3. See pwm.yaml in this directory for a description of the cells format. Optional properties:
Documentation/devicetree/bindings/pwm/pwm-rockchip.txt +1 -1
@@ -14,7 +14,7 @@ Required properties: - For newer hardware (rk3328 and future socs): specified by name - "pwm": This is used to derive the functional clock. - "pclk": This is the APB bus clock. - - #pwm-cells: must be 2 (rk2928) or 3 (rk3288). See pwm.txt in this directory + - #pwm-cells: must be 2 (rk2928) or 3 (rk3288). See pwm.yaml in this directory for a description of the cell format. Example:
Documentation/devicetree/bindings/pwm/pwm-sifive.txt +1 -1
@@ -17,7 +17,7 @@ Required properties: Please refer to sifive-blocks-ip-versioning.txt for details. - reg: physical base address and length of the controller's registers - clocks: Should contain a clock identifier for the PWM's parent clock. -- #pwm-cells: Should be 3. See pwm.txt in this directory +- #pwm-cells: Should be 3. See pwm.yaml in this directory for a description of the cell format. - interrupts: one interrupt per PWM channel
Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt +1 -1
@@ -8,7 +8,7 @@ See ../mfd/stm32-lptimer.txt for details about the parent node. Required parameters: - compatible: Must be "st,stm32-pwm-lp". - #pwm-cells: Should be set to 3. This PWM chip uses the default 3 cells - bindings defined in pwm.txt. + bindings defined in pwm.yaml. Optional properties: - pinctrl-names: Set to "default". An additional "sleep" state can be
Documentation/devicetree/bindings/pwm/pwm-stm32.txt +1 -1
@@ -9,7 +9,7 @@ Required parameters: - pinctrl-0: List of phandles pointing to pin configuration nodes for PWM module. For Pinctrl properties see ../pinctrl/pinctrl-bindings.txt - #pwm-cells: Should be set to 3. This PWM chip uses the default 3 cells - bindings defined in pwm.txt. + bindings defined in pwm.yaml. Optional parameters: - st,breakinput: One or two <index level filter> to describe break input configurations.
Documentation/devicetree/bindings/pwm/pwm-tiecap.txt +1 -1
@@ -8,7 +8,7 @@ Required properties: for dra746 - compatible = "ti,dra746-ecap", "ti,am3352-ecap"; for 66ak2g - compatible = "ti,k2g-ecap", "ti,am3352-ecap"; for am654 - compatible = "ti,am654-ecap", "ti,am3352-ecap"; -- #pwm-cells: should be 3. See pwm.txt in this directory for a description of +- #pwm-cells: should be 3. See pwm.yaml in this directory for a description of the cells format. The PWM channel index ranges from 0 to 4. The only third cell flag supported by this binding is PWM_POLARITY_INVERTED. - reg: physical base address and size of the registers map.
Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt +1 -1
@@ -7,7 +7,7 @@ Required properties: for am654 - compatible = "ti,am654-ehrpwm", "ti-am3352-ehrpwm"; for da850 - compatible = "ti,da850-ehrpwm", "ti-am3352-ehrpwm", "ti,am33xx-ehrpwm"; for dra746 - compatible = "ti,dra746-ehrpwm", "ti-am3352-ehrpwm"; -- #pwm-cells: should be 3. See pwm.txt in this directory for a description of +- #pwm-cells: should be 3. See pwm.yaml in this directory for a description of the cells format. The only third cell flag supported by this binding is PWM_POLARITY_INVERTED. - reg: physical base address and size of the registers map.
Documentation/devicetree/bindings/pwm/pwm-zx.txt +1 -1
@@ -7,7 +7,7 @@ Required properties: - clock-names: "pclk" for PCLK, "wclk" for WCLK to the PWM controller. The PCLK is for register access, while WCLK is the reference clock for calculating period and duty cycles. - - #pwm-cells: Should be 3. See pwm.txt in this directory for a description of + - #pwm-cells: Should be 3. See pwm.yaml in this directory for a description of the cells format. Example:
Documentation/devicetree/bindings/pwm/pwm.txt deleted +0 -69
69 lines not on this page · raw message
Documentation/devicetree/bindings/pwm/pwm.yaml new file +29 -0
@@ -0,0 +1,29 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pwm/pwm.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: PWM controllers (providers) + +maintainers: + - Thierry Reding <[email protected]> + +properties: + $nodename: + pattern: "^pwm(@.*|-[0-9a-f])*$" + + "#pwm-cells": + description: + Number of cells in a PWM specifier. + +required: + - "#pwm-cells" + +examples: + - | + pwm: pwm@7000a000 { + compatible = "nvidia,tegra20-pwm"; + reg = <0x7000a000 0x100>; + #pwm-cells = <2>; + };
Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt +1 -1
@@ -20,7 +20,7 @@ Required Properties: - "renesas,pwm-r8a77990": for R-Car E3 - "renesas,pwm-r8a77995": for R-Car D3 - reg: base address and length of the registers block for the PWM. -- #pwm-cells: should be 2. See pwm.txt in this directory for a description of +- #pwm-cells: should be 2. See pwm.yaml in this directory for a description of the cells format. - clocks: clock phandle and specifier pair. - pinctrl-0: phandle, referring to a default pin configuration node.
Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt +2 -2
@@ -19,11 +19,11 @@ Required Properties: - reg: Base address and length of each memory resource used by the PWM controller hardware module. - - #pwm-cells: should be 3. See pwm.txt in this directory for a description of + - #pwm-cells: should be 3. See pwm.yaml in this directory for a description of the cells format. The only third cell flag supported by this binding is PWM_POLARITY_INVERTED. -Please refer to pwm.txt in this directory for details of the common PWM bindings +Please refer to pwm-consumers.yaml in this directory for details of the common PWM bindings used by client devices. Example: R8A7740 (R-Mobile A1) TPU controller node
Documentation/devicetree/bindings/pwm/spear-pwm.txt +1 -1
@@ -5,7 +5,7 @@ Required properties: - "st,spear320-pwm" - "st,spear1340-pwm" - reg: physical base address and length of the controller's registers -- #pwm-cells: should be 2. See pwm.txt in this directory for a description of +- #pwm-cells: should be 2. See pwm.yaml in this directory for a description of the cells format. Example:
Documentation/devicetree/bindings/pwm/st,stmpe-pwm.txt +1 -1
@@ -7,7 +7,7 @@ subdevices of the STMPE MFD device. Required properties: - compatible: should be: - "st,stmpe-pwm" -- #pwm-cells: should be 2. See pwm.txt in this directory for a description of +- #pwm-cells: should be 2. See pwm.yaml in this directory for a description of the cells format. Example:
Documentation/devicetree/bindings/pwm/ti,twl-pwm.txt +1 -1
@@ -6,7 +6,7 @@ On TWL6030 series: PWM0 and PWM1 Required properties: - compatible: "ti,twl4030-pwm" or "ti,twl6030-pwm" -- #pwm-cells: should be 2. See pwm.txt in this directory for a description of +- #pwm-cells: should be 2. See pwm.yaml in this directory for a description of the cells format. Example:
Documentation/devicetree/bindings/pwm/ti,twl-pwmled.txt +1 -1
@@ -6,7 +6,7 @@ On TWL6030 series: LED PWM (mainly used as charging indicator LED) Required properties: - compatible: "ti,twl4030-pwmled" or "ti,twl6030-pwmled" -- #pwm-cells: should be 2. See pwm.txt in this directory for a description of +- #pwm-cells: should be 2. See pwm.yaml in this directory for a description of the cells format. Example:
Documentation/devicetree/bindings/pwm/vt8500-pwm.txt +1 -1
@@ -3,7 +3,7 @@ VIA/Wondermedia VT8500/WM8xxx series SoC PWM controller Required properties: - compatible: should be "via,vt8500-pwm" - reg: physical base address and length of the controller's registers -- #pwm-cells: should be 3. See pwm.txt in this directory for a description of +- #pwm-cells: should be 3. See pwm.yaml in this directory for a description of the cells format. The only third cell flag supported by this binding is PWM_POLARITY_INVERTED. - clocks: phandle to the PWM source clock
Documentation/devicetree/bindings/regulator/pwm-regulator.txt +1 -1
@@ -27,7 +27,7 @@ Required properties: -------------------- - compatible: Should be "pwm-regulator" -- pwms: PWM specification (See: ../pwm/pwm.txt) +- pwms: PWM specification (See: ../pwm/pwm-consumers.yaml) Only required for Voltage Table Mode: - voltage-table: Voltage and Duty-Cycle table consisting of 2 cells
Documentation/devicetree/bindings/timer/ingenic,tcu.txt +1 -1
@@ -42,7 +42,7 @@ Required properties: - compatible: Must be one of: * ingenic,jz4740-pwm * ingenic,jz4725b-pwm -- #pwm-cells: Should be 3. See ../pwm/pwm.txt for a description of the cell +- #pwm-cells: Should be 3. See ../pwm/pwm.yaml for a description of the cell format. - clocks: List of phandle & clock specifiers for the TCU clocks. - clock-names: List of name strings for the TCU clocks.
Signature · 6 lines
2.17.1 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Krzysztof Kozlowski
maintainerPATCH v2 8/8 dt-bindings: pwm: Convert Samsung PWM bindings to json-schema
In reply to Krzysztof KozlowskiConvert Samsung PWM (S3C, S5P and Exynos SoCs) bindings to DT schema format using json-schema.
---
Changes since v1:
1. Indent example with four spaces (more readable),
2. Fix samsung,pwm-outputs after review,
3. Remove double-quotes from clock names.
--- .../devicetree/bindings/pwm/pwm-samsung.txt | 51 --------- .../devicetree/bindings/pwm/pwm-samsung.yaml | 107 ++++++++++++++++++ 2 files changed, 107 insertions(+), 51 deletions(-) delete mode 100644 Documentation/devicetree/bindings/pwm/pwm-samsung.txt create mode 100644 Documentation/devicetree/bindings/pwm/pwm-samsung.yaml
Documentation/devicetree/bindings/pwm/pwm-samsung.txt deleted +0 -51
@@ -1,51 +0,0 @@ -* Samsung PWM timers - -Samsung SoCs contain PWM timer blocks which can be used for system clock source -and clock event timers, as well as to drive SoC outputs with PWM signal. Each -PWM timer block provides 5 PWM channels (not all of them can drive physical -outputs - see SoC and board manual). - -Be aware that the clocksource driver supports only uniprocessor systems. - -Required properties: -- compatible : should be one of following: - samsung,s3c2410-pwm - for 16-bit timers present on S3C24xx SoCs - samsung,s3c6400-pwm - for 32-bit timers present on S3C64xx SoCs - samsung,s5p6440-pwm - for 32-bit timers present on S5P64x0 SoCs - samsung,s5pc100-pwm - for 32-bit timers present on S5PC100, S5PV210, - Exynos4210 rev0 SoCs - samsung,exynos4210-pwm - for 32-bit timers present on Exynos4210, - Exynos4x12, Exynos5250 and Exynos5420 SoCs -- reg: base address and size of register area -- interrupts: list of timer interrupts (one interrupt per timer, starting at - timer 0) -- clock-names: should contain all following required clock names: - - "timers" - PWM base clock used to generate PWM signals, - and any subset of following optional clock names: - - "pwm-tclk0" - first external PWM clock source, - - "pwm-tclk1" - second external PWM clock source. - Note that not all IP variants allow using all external clock sources. - Refer to SoC documentation to learn which clock source configurations - are available. -- clocks: should contain clock specifiers of all clocks, which input names - have been specified in clock-names property, in same order. -- #pwm-cells: should be 3. See pwm.txt in this directory for a description of - the cells format. The only third cell flag supported by this binding is - PWM_POLARITY_INVERTED. - -Optional properties: -- samsung,pwm-outputs: list of PWM channels used as PWM outputs on particular - platform - an array of up to 5 elements being indices of PWM channels - (from 0 to 4), the order does not matter. - -Example: - pwm@7f006000 { - compatible = "samsung,s3c6400-pwm"; - reg = <0x7f006000 0x1000>; - interrupt-parent = <&vic0>; - interrupts = <23>, <24>, <25>, <27>, <28>; - clocks = <&clock 67>; - clock-names = "timers"; - samsung,pwm-outputs = <0>, <1>; - #pwm-cells = <3>; - }
Documentation/devicetree/bindings/pwm/pwm-samsung.yaml new file +107 -0
107 lines not on this page · raw message
Signature · 6 lines
2.17.1 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH v2 8/8] dt-bindings: pwm: Convert Samsung PWM bindings to json-schema
Quoted 166 lines · Krzysztof Kozlowski
Convert Samsung PWM (S3C, S5P and Exynos SoCs) bindings to DT schema format using json-schema.
Signed-off-by Krzysztof Kozlowski <[email protected]>---
Changes since v1:
1. Indent example with four spaces (more readable),
2. Fix samsung,pwm-outputs after review,
3. Remove double-quotes from clock names.--- .../devicetree/bindings/pwm/pwm-samsung.txt | 51 --------- .../devicetree/bindings/pwm/pwm-samsung.yaml | 107 ++++++++++++++++++ 2 files changed, 107 insertions(+), 51 deletions(-) delete mode 100644 Documentation/devicetree/bindings/pwm/pwm-samsung.txt create mode 100644 Documentation/devicetree/bindings/pwm/pwm-samsung.yamlDocumentation/devicetree/bindings/pwm/pwm-samsung.txt deleted +0
-51@@ -1,51 +0,0 @@ -* Samsung PWM timers - -Samsung SoCs contain PWM timer blocks which can be used for system clock source -and clock event timers, as well as to drive SoC outputs with PWM signal. Each -PWM timer block provides 5 PWM channels (not all of them can drive physical -outputs - see SoC and board manual). - -Be aware that the clocksource driver supports only uniprocessor systems. - -Required properties: -- compatible : should be one of following: - samsung,s3c2410-pwm - for 16-bit timers present on S3C24xx SoCs - samsung,s3c6400-pwm - for 32-bit timers present on S3C64xx SoCs - samsung,s5p6440-pwm - for 32-bit timers present on S5P64x0 SoCs - samsung,s5pc100-pwm - for 32-bit timers present on S5PC100, S5PV210, - Exynos4210 rev0 SoCs - samsung,exynos4210-pwm - for 32-bit timers present on Exynos4210, - Exynos4x12, Exynos5250 and Exynos5420 SoCs -- reg: base address and size of register area -- interrupts: list of timer interrupts (one interrupt per timer, starting at - timer 0) -- clock-names: should contain all following required clock names: - - "timers" - PWM base clock used to generate PWM signals, - and any subset of following optional clock names: - - "pwm-tclk0" - first external PWM clock source, - - "pwm-tclk1" - second external PWM clock source. - Note that not all IP variants allow using all external clock sources. - Refer to SoC documentation to learn which clock source configurations - are available. -- clocks: should contain clock specifiers of all clocks, which input names - have been specified in clock-names property, in same order. -- #pwm-cells: should be 3. See pwm.txt in this directory for a description of - the cells format. The only third cell flag supported by this binding is - PWM_POLARITY_INVERTED. - -Optional properties: -- samsung,pwm-outputs: list of PWM channels used as PWM outputs on particular - platform - an array of up to 5 elements being indices of PWM channels - (from 0 to 4), the order does not matter. - -Example: - pwm@7f006000 { - compatible = "samsung,s3c6400-pwm"; - reg = <0x7f006000 0x1000>; - interrupt-parent = <&vic0>; - interrupts = <23>, <24>, <25>, <27>, <28>; - clocks = <&clock 67>; - clock-names = "timers"; - samsung,pwm-outputs = <0>, <1>; - #pwm-cells = <3>; - }Documentation/devicetree/bindings/pwm/pwm-samsung.yaml new file +84
-0@@ -0,0 +1,107 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pwm/pwm-samsung.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung SoC PWM timers + +maintainers: + - Thierry Reding <[email protected]> + - Krzysztof Kozlowski <[email protected]> + +description: |+ + Samsung SoCs contain PWM timer blocks which can be used for system clock source + and clock event timers, as well as to drive SoC outputs with PWM signal. Each + PWM timer block provides 5 PWM channels (not all of them can drive physical + outputs - see SoC and board manual). + + Be aware that the clocksource driver supports only uniprocessor systems. + +allOf: + - $ref: pwm.yaml# + +properties: + compatible: + enum: + - samsung,s3c2410-pwm # 16-bit, S3C24xx + - samsung,s3c6400-pwm # 32-bit, S3C64xx + - samsung,s5p6440-pwm # 32-bit, S5P64x0 + - samsung,s5pc100-pwm # 32-bit, S5PC100, S5PV210, Exynos4210 rev0 SoCs + - samsung,exynos4210-pwm # 32-bit, Exynos + + reg: + maxItems: 1 + + clocks: + minItems: 1 + maxItems: 3 + + clock-names: + description: | + Should contain all following required clock names: + - "timers" - PWM base clock used to generate PWM signals, + and any subset of following optional clock names: + - "pwm-tclk0" - first external PWM clock source, + - "pwm-tclk1" - second external PWM clock source. + Note that not all IP variants allow using all external clock sources. + Refer to SoC documentation to learn which clock source configurations + are available. + oneOf: + - items: + - const: timers + - items: + - const: timers + - const: pwm-tclk0 + - items: + - const: timers + - const: pwm-tclk1 + - items: + - const: timers + - const: pwm-tclk0 + - const: pwm-tclk1 + + interrupts: + description: + One interrupt per timer, starting at timer 0. + minItems: 1 + maxItems: 5 + + "#pwm-cells": + description: + The only third cell flag supported by this binding + is PWM_POLARITY_INVERTED. + const: 3 + + samsung,pwm-outputs: + description: + A list of PWM channels used as PWM outputs on particular platform. + It is an array of up to 5 elements being indices of PWM channels + (from 0 to 4), the order does not matter. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32-array + - uniqueItems: true + - items:
Documentation/devicetree/bindings/pwm/pwm-samsung.yaml line 94
Quoted 10 lines
Documentation/devicetree/bindings/pwm/pwm-samsung.yaml new file +10
-0+ minimum: 0 + maximum: 4 + +required: + - clocks + - clock-names + - compatible + - interrupts + - "#pwm-cells" + - reg
additionalProperties: false
should work here. And in the rng binding too.
Rob
Krzysztof Kozlowski
maintainerRe: [PATCH v2 5/8] dt-bindings: watchdog: Convert Samsung SoC watchdog bindings to json-schema
In reply to Krzysztof KozlowskiQuoted 11 lines · Krzysztof Kozlowski
Convert Samsung S3C/S5P/Exynos watchdog bindings to DT schema format using json-schema.
Signed-off-by Krzysztof Kozlowski <[email protected]>---
Changes since v1:
1. Indent example with four spaces (more readable),
2. Remove unneeded timeout-sec description.
Superseded by v3 (although named v2...).
Best regards,
Krzysztof
Rob Herring
maintainerRe: [PATCH v2 2/8] dt-bindings: sram: Convert SRAM bindings to json-schema
In reply to Krzysztof KozlowskiQuoted 2 lines · Krzysztof Kozlowski
Convert generic mmio-sram bindings to DT schema format using json-schema.
I've been slow getting to this because I started on the same thing...
Quoted 20 lines
Signed-off-by Krzysztof Kozlowski <[email protected]>---
Changes since v1:
1. Indent example with four spaces (more readable).--- .../devicetree/bindings/sram/sram.txt | 80 ---------- .../devicetree/bindings/sram/sram.yaml | 138 ++++++++++++++++++ 2 files changed, 138 insertions(+), 80 deletions(-) delete mode 100644 Documentation/devicetree/bindings/sram/sram.txt create mode 100644 Documentation/devicetree/bindings/sram/sram.yamlDocumentation/devicetree/bindings/sram/sram.yaml new file +0
-0
Documentation/devicetree/bindings/sram/sram.yaml line 10
Quoted 10 lines
Documentation/devicetree/bindings/sram/sram.yaml new file +10
-0@@ -0,0 +1,138 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/sram/sram.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Generic on-chip SRAM + +maintainers: + - FIXME <[email protected]>
You can put me.
Quoted 11 lines
Documentation/devicetree/bindings/sram/sram.yaml new file +11
-0+ +description: |+ + Simple IO memory regions to be managed by the genalloc API. + + Each child of the sram node specifies a region of reserved memory. Each + child node should use a 'reg' property to specify a specific range of + reserved memory. + + Following the generic-names recommended practice, node names should + reflect the purpose of the node. Unit address (@<address>) should be + appended to the name.
Documentation/devicetree/bindings/sram/sram.yaml line 31
Quoted 10 lines
Documentation/devicetree/bindings/sram/sram.yaml new file +10
-0+ +properties: + $nodename: + pattern: "^sram(@.*)?" + + compatible: + items: + - enum: + - mmio-sram + - atmel,sama5d2-securam
I was trying to go down the path of putting all the compatibles for various SRAM bindings here, but I ran into some issues. I need to revisit as I've forgotten the exact issue.
This would need to be a 'contains' if this is going to work for others.
Documentation/devicetree/bindings/sram/sram.yaml line 40
Quoted 9 lines
Documentation/devicetree/bindings/sram/sram.yaml new file +9
-0+ + reg: + maxItems: 1 + + "#address-cells": + description: Should use the same values as the root node. + + "#size-cells": + description: Should use the same values as the root node.
I defined both of these to be 1 as 4GB of SRAM should be enough for a while. We can debate 1 or 2 cells vs. 1, but there's no reason it has to be the same as the root (unless we're failing to do address translation).
Quoted 12 lines
Documentation/devicetree/bindings/sram/sram.yaml new file +12
-0+ + ranges: + description: + Should translate from local addresses within the sram to bus addresses. + + no-memory-wc: + description: + The flag indicating, that SRAM memory region has not to be remapped + as write combining. WC is used by default. + type: boolean + + # TODO: additionalProperties: false
Documentation/devicetree/bindings/sram/sram.yaml line 62
Quoted 10 lines
Documentation/devicetree/bindings/sram/sram.yaml new file +10
-0+ +patternProperties: + "^([a-z]*-)?sram@[a-f0-9]$": + type: object + description: + Each child of the sram node specifies a region of reserved memory. + properties: + reg: + description: + IO mem address range, relative to the SRAM range.
maxItems: 1
Quoted 20 lines
Documentation/devicetree/bindings/sram/sram.yaml new file +20
-0+ + compatible: + $ref: /schemas/types.yaml#/definitions/string + description: + Should contain a vendor specific string in the form + <vendor>,[<device>-]<usage> + + pool: + description: + Indicates that the particular reserved SRAM area is addressable + and in use by another device or devices. + type: boolean + + export: + description: + Indicates that the reserved SRAM area may be accessed outside + of the kernel, e.g. by bootloader or userspace. + type: boolean + + protect-exec:
Documentation/devicetree/bindings/sram/sram.yaml line 92
Quoted 10 lines
Documentation/devicetree/bindings/sram/sram.yaml new file +10
-0+ description: | + Same as 'pool' above but with the additional constraint that code + will be run from the region and that the memory is maintained as + read-only, executable during code execution. NOTE: This region must + be page aligned on start and end in order to properly allow + manipulation of the page attributes. + type: boolean + + label: + $ref: /schemas/types.yaml#/definitions/string
Already has a type definition.
Quoted 49 lines
Documentation/devicetree/bindings/sram/sram.yaml new file +46
-0+ description: + The name for the reserved partition, if omitted, the label is taken + from the node name excluding the unit address. + + clocks: + description: + A list of phandle and clock specifier pair that controls the + single SRAM clock. + + # TODO: additionalProperties: false + + required: + - reg + +required: + - compatible + - reg + - "#address-cells" + - "#size-cells" + - ranges + +examples: + - | + sram: sram@5c000000 { + compatible = "mmio-sram"; + reg = <0x5c000000 0x40000>; /* 256 KiB SRAM at address 0x5c000000 */ + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x5c000000 0x40000>; + + smp-sram@100 { + compatible = "socvendor,smp-sram"; + reg = <0x100 0x50>; + }; + + device-sram@1000 { + reg = <0x1000 0x1000>; + pool; + }; + + exported@20000 { + reg = <0x20000 0x20000>; + export; + }; + };Signature · 1 line
2.17.1
Krzysztof Kozlowski
maintainerRe: [PATCH v2 2/8] dt-bindings: sram: Convert SRAM bindings to json-schema
Quoted 30 lines · Rob Herring
Quoted 2 lines · Krzysztof Kozlowski
Convert generic mmio-sram bindings to DT schema format using json-schema.
I've been slow getting to this because I started on the same thing...
Quoted 24 lines
Signed-off-by Krzysztof Kozlowski <[email protected]>---
Changes since v1:
1. Indent example with four spaces (more readable).--- .../devicetree/bindings/sram/sram.txt | 80 ---------- .../devicetree/bindings/sram/sram.yaml | 138 ++++++++++++++++++ 2 files changed, 138 insertions(+), 80 deletions(-) delete mode 100644 Documentation/devicetree/bindings/sram/sram.txt create mode 100644 Documentation/devicetree/bindings/sram/sram.yamlDocumentation/devicetree/bindings/sram/sram.yaml new file +4
-0@@ -0,0 +1,138 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/sram/sram.yaml#
Quoted 8 lines
Documentation/devicetree/bindings/sram/sram.yaml line 10
Quoted 6 lines
Documentation/devicetree/bindings/sram/sram.yaml new file +6
-0+$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Generic on-chip SRAM + +maintainers: + - FIXME <[email protected]>You can put me.
Sure.
Quoted 27 lines
Quoted 12 lines
Documentation/devicetree/bindings/sram/sram.yaml new file +11
-0+ +description: |+ + Simple IO memory regions to be managed by the genalloc API. + + Each child of the sram node specifies a region of reserved memory. Each + child node should use a 'reg' property to specify a specific range of + reserved memory. + + Following the generic-names recommended practice, node names should + reflect the purpose of the node. Unit address (@<address>) should be + appended to the name.Documentation/devicetree/bindings/sram/sram.yaml line 31
Quoted 10 lines
Documentation/devicetree/bindings/sram/sram.yaml new file +10
-0+ +properties: + $nodename: + pattern: "^sram(@.*)?" + + compatible: + items: + - enum: + - mmio-sram + - atmel,sama5d2-securamI was trying to go down the path of putting all the compatibles for various SRAM bindings here, but I ran into some issues. I need to revisit as I've forgotten the exact issue.
Quoted 1 line
This would need to be a 'contains' if this is going to work for others.
OK.
Quoted 15 lines
Documentation/devicetree/bindings/sram/sram.yaml line 40
Quoted 10 lines
Documentation/devicetree/bindings/sram/sram.yaml new file +9
-0+ + reg: + maxItems: 1 + + "#address-cells": + description: Should use the same values as the root node. + + "#size-cells": + description: Should use the same values as the root node.I defined both of these to be 1 as 4GB of SRAM should be enough for a while. We can debate 1 or 2 cells vs. 1, but there's no reason it has to be the same as the root (unless we're failing to do address translation).
That was copied from txt version. I can adjust them to 1 although this is will more than simple conversion.
Quoted 17 lines
Quoted 17 lines
Documentation/devicetree/bindings/sram/sram.yaml new file +16
-0+ + ranges: + description: + Should translate from local addresses within the sram to bus addresses. + + no-memory-wc: + description: + The flag indicating, that SRAM memory region has not to be remapped + as write combining. WC is used by default. + type: boolean + + # TODO: additionalProperties: false + +patternProperties: + "^([a-z]*-)?sram@[a-f0-9]$": + type: object
Quoted 8 lines
Documentation/devicetree/bindings/sram/sram.yaml line 62
Quoted 6 lines
Documentation/devicetree/bindings/sram/sram.yaml new file +6
-0+ description: + Each child of the sram node specifies a region of reserved memory. + properties: + reg: + description: + IO mem address range, relative to the SRAM range.maxItems: 1
OK
Quoted 25 lines
Quoted 25 lines
Documentation/devicetree/bindings/sram/sram.yaml new file +24
-0+ + compatible: + $ref: /schemas/types.yaml#/definitions/string + description: + Should contain a vendor specific string in the form + <vendor>,[<device>-]<usage> + + pool: + description: + Indicates that the particular reserved SRAM area is addressable + and in use by another device or devices. + type: boolean + + export: + description: + Indicates that the reserved SRAM area may be accessed outside + of the kernel, e.g. by bootloader or userspace. + type: boolean + + protect-exec: + description: | + Same as 'pool' above but with the additional constraint that code + will be run from the region and that the memory is maintained as + read-only, executable during code execution. NOTE: This region must
Quoted 8 lines
Documentation/devicetree/bindings/sram/sram.yaml line 92
Quoted 6 lines
Documentation/devicetree/bindings/sram/sram.yaml new file +6
-0+ be page aligned on start and end in order to properly allow + manipulation of the page attributes. + type: boolean + + label: + $ref: /schemas/types.yaml#/definitions/stringAlready has a type definition.
OK
Best regards,
Krzysztof
Re: [PATCH v2 4/8] dt-bindings: memory-controllers: Convert Samsung Exynos SROM bindings to json-schema
In reply to Krzysztof KozlowskiQuoted 14 lines · Krzysztof Kozlowski
Convert Samsung Exynos SROM controller bindings to DT schema format using json-schema.
Signed-off-by Krzysztof Kozlowski <[email protected]>---
Changes since v1:
1. Indent example with four spaces (more readable),
2. Split examples into two,
3. Fix pattern for subnode name,
4. Remove checks for #address-cells-ranges-#size-cells,
5. Add "additionalProperties" so the wrongly named subnodes would be matched.
Quoted 7 lines
--- .../memory-controllers/exynos-srom.txt | 79 ----------- .../memory-controllers/exynos-srom.yaml | 128 ++++++++++++++++++ 2 files changed, 128 insertions(+), 79 deletions(-) delete mode 100644 Documentation/devicetree/bindings/memory-controllers/exynos-srom.txt create mode 100644 Documentation/devicetree/bindings/memory-controllers/exynos-srom.yaml
Applied, thanks.
Rob