Skip to contentSkip to conversation

ALSA: hda: Flush interrupts on disabling

PATCH In review Sasha Levin 8 participants 217 messages Sep 22, 2019 – Oct 2, 2019 Page 1 of 2

Subsystems (34)
lore
Share & tools
lore
author maintainer
#6 lore raw

PATCH 7/203 spi: dw-mmio: Clock should be shut when error occurs

In reply to Sasha Levin

From: Andy Shevchenko <[email protected]>

[ Upstream commit 3da9834d9381dd99273f2ad4e6d096c9187dc4f2 ]

When optional clock requesting fails, the main clock is still up and running, we should shut it down in such caee.

Fixes 560ee7e91009 ("spi: dw: Add support for an optional interface clock")
Cc Phil Edworthy <[email protected]>
Cc Gareth Williams <[email protected]>
---
 drivers/spi/spi-dw-mmio.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
drivers/spi/spi-dw-mmio.c +4 -2
index 18c06568805e7..86789dbaf5771 100644
@@ -172,8 +172,10 @@ static int dw_spi_mmio_probe(struct platform_device *pdev)
 
 	/* Optional clock needed to access the registers */
 	dwsmmio->pclk = devm_clk_get_optional(&pdev->dev, "pclk");
-	if (IS_ERR(dwsmmio->pclk))
-		return PTR_ERR(dwsmmio->pclk);
+	if (IS_ERR(dwsmmio->pclk)) {
+		ret = PTR_ERR(dwsmmio->pclk);
+		goto out_clk;
+	}
 	ret = clk_prepare_enable(dwsmmio->pclk);
 	if (ret)
 		goto out_clk;
Signature · 1 line
2.20.1
author maintainer
#38 lore raw

PATCH 37/203 arm64: dts: imx8mq: Correct OPP table according to latest datasheet

In reply to Sasha Levin

From: Anson Huang <[email protected]>

[ Upstream commit 9eced3a2f224a62a233761e8af18c907c532e192 ]

According to latest datasheet (Rev.1, 10/2018) from below links, in the consumer datasheet, 1.5GHz is mentioned as highest opp but depends on speed grading fuse, and in the industrial datasheet, 1.3GHz is mentioned as highest opp but depends on speed grading fuse. 1.5GHz and 1.3GHz opp use same voltage, so no need for consumer part to support 1.3GHz opp, with same voltage, CPU should run at highest frequency in order to go into idle as quick as possible, this can save power.

That means for consumer part, 1GHz/1.5GHz are supported, for industrial part, 800MHz/1.3GHz are supported, and then check the speed grading fuse to limit the highest CPU frequency further. Correct the market segment bits in opp table to make them work according to datasheets.

https://www.nxp.com/docs/en/data-sheet/IMX8MDQLQIEC.pdf
https://www.nxp.com/docs/en/data-sheet/IMX8MDQLQCEC.pdf

Fixes 12629c5c3749 ("arm64: dts: imx8mq: Add cpu speed grading and all OPPs")
---
 arch/arm64/boot/dts/freescale/imx8mq.dtsi | 5 ++---
 1 file changed, 2 insertions(+), 3 deletions(-)
arch/arm64/boot/dts/freescale/imx8mq.dtsi +2 -3
index 52aae341d0da5..d1f4eb197af26 100644
@@ -169,15 +169,14 @@
 		opp-1300000000 {
 			opp-hz = /bits/ 64 <1300000000>;
 			opp-microvolt = <1000000>;
-			opp-supported-hw = <0xc>, <0x7>;
+			opp-supported-hw = <0xc>, <0x4>;
 			clock-latency-ns = <150000>;
 		};
 
 		opp-1500000000 {
 			opp-hz = /bits/ 64 <1500000000>;
 			opp-microvolt = <1000000>;
-			/* Consumer only but rely on speed grading */
-			opp-supported-hw = <0x8>, <0x7>;
+			opp-supported-hw = <0x8>, <0x3>;
 			clock-latency-ns = <150000>;
 		};
 	};
Signature · 1 line
2.20.1
author maintainer
#47 lore raw

PATCH 46/203 ia64:unwind: fix double free for mod->arch.init_unw_table

In reply to Sasha Levin

From: chenzefeng <[email protected]>

[ Upstream commit c5e5c48c16422521d363c33cfb0dcf58f88c119b ]

The function free_module in file kernel/module.c as follow:

void free_module(struct module *mod) {
	......
	module_arch_cleanup(mod);
	......
	module_arch_freeing_init(mod);
	......
}

Both module_arch_cleanup and module_arch_freeing_init function would free the mod->arch.init_unw_table, which cause double free.

Here, set mod->arch.init_unw_table = NULL after remove the unwind table to avoid double free.

---
 arch/ia64/kernel/module.c | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)
arch/ia64/kernel/module.c +6 -2
index 326448f9df160..1a42ba885188a 100644
@@ -914,10 +914,14 @@ module_finalize (const Elf_Ehdr *hdr, const Elf_Shdr *sechdrs, struct module *mo
 void
 module_arch_cleanup (struct module *mod)
 {
-	if (mod->arch.init_unw_table)
+	if (mod->arch.init_unw_table) {
 		unw_remove_unwind_table(mod->arch.init_unw_table);
-	if (mod->arch.core_unw_table)
+		mod->arch.init_unw_table = NULL;
+	}
+	if (mod->arch.core_unw_table) {
 		unw_remove_unwind_table(mod->arch.core_unw_table);
+		mod->arch.core_unw_table = NULL;
+	}
 }
 
 void *dereference_module_function_descriptor(struct module *mod, void *ptr)
Signature · 1 line
2.20.1
author maintainer
#48 lore raw

PATCH 47/203 EDAC/altera: Use the proper type for the IRQ status bits

In reply to Sasha Levin

From: Dan Carpenter <[email protected]>

[ Upstream commit 8faa1cf6ed82f33009f63986c3776cc48af1b7b2 ]

Smatch complains about the cast of a u32 pointer to unsigned long:

drivers/edac/altera_edac.c:1878 altr_edac_a10_irq_handler()
warn: passing casted pointer '&irq_status' to 'find_first_bit()'

This code wouldn't work on a 64 bit big endian system because it would read past the end of &irq_status.

[ bp: massage. ]

Fixes 13ab8448d2c9 ("EDAC, altera: Add ECC Manager IRQ controller support")
Cc James Morse <[email protected]>
Cc linux-edac <[email protected]>
Cc Mauro Carvalho Chehab <[email protected]>
Cc Tony Luck <[email protected]>
---
 drivers/edac/altera_edac.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/edac/altera_edac.c +3 -1
index c2e693e34d434..bf024ec0116c7 100644
@@ -1866,6 +1866,7 @@ static void altr_edac_a10_irq_handler(struct irq_desc *desc)
 	struct altr_arria10_edac *edac = irq_desc_get_handler_data(desc);
 	struct irq_chip *chip = irq_desc_get_chip(desc);
 	int irq = irq_desc_get_irq(desc);
+	unsigned long bits;
 
 	dberr = (irq = edac->db_irq) ? 1 : 0;
 	sm_offset = dberr ? A10_SYSMGR_ECC_INTSTAT_DERR_OFST :
@@ -1875,7 +1876,8 @@ static void altr_edac_a10_irq_handler(struct irq_desc *desc)
 
 	regmap_read(edac->ecc_mgr_map, sm_offset, &irq_status);
 
-	for_each_set_bit(bit, (unsigned long *)&irq_status, 32) {
+	bits = irq_status;
+	for_each_set_bit(bit, &bits, 32) {
 		irq = irq_linear_revmap(edac->domain, dberr * 32 + bit);
 		if (irq)
 			generic_handle_irq(irq);
Signature · 1 line
2.20.1
author maintainer
#51 lore raw

PATCH 50/203 md/raid1: end bio when the device faulty

In reply to Sasha Levin

From: Yufen Yu <[email protected]>

[ Upstream commit eeba6809d8d58908b5ed1b5ceb5fcb09a98a7cad ]

When write bio return error, it would be added to conf->retry_list and wait for raid1d thread to retry write and acknowledge badblocks.

In narrow_write_error(), the error bio will be split in the unit of badblock shift (such as one sector) and raid1d thread issues them one by one. Until all of the splited bio has finished, raid1d thread can go on processing other things, which is time consuming.

But, there is a scene for error handling that is not necessary. When the device has been set faulty, flush_bio_list() may end bios in pending_bio_list with error status. Since these bios has not been issued to the device actually, error handlding to retry write and acknowledge badblocks make no sense.

Even without that scene, when the device is faulty, badblocks info can not be written out to the device. Thus, we also no need to handle the error IO.

---
 drivers/md/raid1.c | 26 ++++++++++++++------------
 1 file changed, 14 insertions(+), 12 deletions(-)
drivers/md/raid1.c +14 -12
index 34e26834ad28b..501a3b4d82f33 100644
@@ -447,19 +447,21 @@ static void raid1_end_write_request(struct bio *bio)
 		    /* We never try FailFast to WriteMostly devices */
 		    !test_bit(WriteMostly, &rdev->flags)) {
 			md_error(r1_bio->mddev, rdev);
-			if (!test_bit(Faulty, &rdev->flags))
-				/* This is the only remaining device,
-				 * We need to retry the write without
-				 * FailFast
-				 */
-				set_bit(R1BIO_WriteError, &r1_bio->state);
-			else {
-				/* Finished with this branch */
-				r1_bio->bios[mirror] = NULL;
-				to_put = bio;
-			}
-		} else
+		}
+
+		/*
+		 * When the device is faulty, it is not necessary to
+		 * handle write error.
+		 * For failfast, this is the only remaining device,
+		 * We need to retry the write without FailFast.
+		 */
+		if (!test_bit(Faulty, &rdev->flags))
 			set_bit(R1BIO_WriteError, &r1_bio->state);
+		else {
+			/* Finished with this branch */
+			r1_bio->bios[mirror] = NULL;
+			to_put = bio;
+		}
 	} else {
 		/*
 		 * Set R1BIO_Uptodate in our master bio, so that we
Signature · 1 line
2.20.1
author maintainer
#52 lore raw

PATCH 51/203 md: don't call spare_active in md_reap_sync_thread if all member devices can't work

In reply to Sasha Levin

From: Guoqing Jiang <[email protected]>

[ Upstream commit 0d8ed0e9bf9643f27f4816dca61081784dedb38d ]

When add one disk to array, the md_reap_sync_thread is responsible to activate the spare and set In_sync flag for the new member in spare_active().

But if raid1 has one member disk A, and disk B is added to the array. Then we offline A before all the datas are synchronized from A to B, obviously B doesn't have the latest data as A, but B is still marked with In_sync flag.

So let's not call spare_active under the condition, otherwise B is still showed with 'U' state which is not correct.

---
 drivers/md/md.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/md/md.c +2 -1
index 24638ccedce42..fd62be3ca2871 100644
@@ -9043,7 +9043,8 @@ void md_reap_sync_thread(struct mddev *mddev)
 	/* resync has finished, collect result */
 	md_unregister_thread(&mddev->sync_thread);
 	if (!test_bit(MD_RECOVERY_INTR, &mddev->recovery) &&
-	    !test_bit(MD_RECOVERY_REQUESTED, &mddev->recovery)) {
+	    !test_bit(MD_RECOVERY_REQUESTED, &mddev->recovery) &&
+	    mddev->degraded != mddev->raid_disks) {
 		/* success...*/
 		/* activate any spares */
 		if (mddev->pers->spare_active(mddev)) {
Signature · 1 line
2.20.1
author maintainer
#53 lore raw

PATCH 52/203 md: don't set In_sync if array is frozen

In reply to Sasha Levin

From: Guoqing Jiang <[email protected]>

[ Upstream commit 062f5b2ae12a153644c765e7ba3b0f825427be1d ]

When a disk is added to array, the following path is called in mdadm.

Manage_subdevs -> sysfs_freeze_array

               -> Manage_add
               -> sysfs_set_str(&info, NULL, "sync_action","idle")

Then from kernel side, Manage_add invokes the path (add_new_disk -> validate_super = super_1_validate) to set In_sync flag.

Since In_sync means "device is in_sync with rest of array", and the new added disk need to resync thread to help the synchronization of data. And md_reap_sync_thread would call spare_active to set In_sync for the new added disk finally. So don't set In_sync if array is in frozen.

---
 drivers/md/md.c | 11 +++++++++--
 1 file changed, 9 insertions(+), 2 deletions(-)
drivers/md/md.c +9 -2
index fd62be3ca2871..232ea1f519963 100644
@@ -1826,8 +1826,15 @@ static int super_1_validate(struct mddev *mddev, struct md_rdev *rdev)
 				if (!(le32_to_cpu(sb->feature_map) &
 				      MD_FEATURE_RECOVERY_BITMAP))
 					rdev->saved_raid_disk = -1;
-			} else
-				set_bit(In_sync, &rdev->flags);
+			} else {
+				/*
+				 * If the array is FROZEN, then the device can't
+				 * be in_sync with rest of array.
+				 */
+				if (!test_bit(MD_RECOVERY_FROZEN,
+					      &mddev->recovery))
+					set_bit(In_sync, &rdev->flags);
+			}
 			rdev->raid_disk = role;
 			break;
 		}
Signature · 1 line
2.20.1
author maintainer
#55 lore raw

PATCH 54/203 media: staging: tegra-vde: Fix build error

In reply to Sasha Levin

From: YueHaibing <[email protected]>

[ Upstream commit 6b2265975239ab655069d796b822835a593e1cc7 ]

If IOMMU_SUPPORT is not set, and COMPILE_TEST is y, IOMMU_IOVA may be set to m. So building will fails:

drivers/staging/media/tegra-vde/iommu.o: In function `tegra_vde_iommu_map':
iommu.c:(.text+0x41): undefined reference to alloc_iova' iommu.c:(.text+0x56): undefined reference to __free_iova'

Select IOMMU_IOVA while COMPILE_TEST is set to fix this.

Fixes b301f8de1925 ("media: staging: media: tegra-vde: Add IOMMU support")
---
 drivers/staging/media/tegra-vde/Kconfig | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/staging/media/tegra-vde/Kconfig +1 -1
index 2e7f644ae5911..ba49ea50b8c0b 100644
@@ -3,7 +3,7 @@ config TEGRA_VDE
 	tristate "NVIDIA Tegra Video Decoder Engine driver"
 	depends on ARCH_TEGRA || COMPILE_TEST
 	select DMA_SHARED_BUFFER
-	select IOMMU_IOVA if IOMMU_SUPPORT
+	select IOMMU_IOVA if (IOMMU_SUPPORT || COMPILE_TEST)
 	select SRAM
 	help
 	    Say Y here to enable support for the NVIDIA Tegra video decoder
Signature · 1 line
2.20.1
author maintainer
#97 lore raw

PATCH 90/203 ARM: dts: imx7d: cl-som-imx7: make ethernet work again

In reply to Sasha Levin

From: André Draszik <[email protected]>

[ Upstream commit 9846a4524ac90b63496580b7ad50674b40d92a8f ]

Recent changes to the atheros at803x driver caused ethernet to stop working on this board.
In particular commit 6d4cd041f0af
("net: phy: at803x: disable delay only for RGMII mode") and commit cd28d1d6e52e
("net: phy: at803x: Disable phy delay for RGMII mode") fix the AR8031 driver to configure the phy's (RX/TX) delays as per the 'phy-mode' in the device tree.

This now prevents ethernet from working on this board.

It used to work before those commits, because the AR8031 comes out of reset with RX delay enabled, and the at803x driver didn't touch the delay configuration at all when "rgmii" mode was selected, and because arch/arm/mach-imx/mach-imx7d.c:ar8031_phy_fixup() unconditionally enables TX delay.

Since above commits ar8031_phy_fixup() also has no effect anymore, and the end-result is that all delays are disabled in the phy, no ethernet.

Update the device tree to restore functionality.

CC Ilya Ledvich <[email protected]>
CC Igor Grinberg <[email protected]>
CC Rob Herring <[email protected]>
CC Mark Rutland <[email protected]>
CC Shawn Guo <[email protected]>
CC Sascha Hauer <[email protected]>
CC Pengutronix Kernel Team <[email protected]>
CC Fabio Estevam <[email protected]>
CC NXP Linux Team <[email protected]>
---
 arch/arm/boot/dts/imx7d-cl-som-imx7.dts | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
arch/arm/boot/dts/imx7d-cl-som-imx7.dts +2 -2
index e61567437d73c..62d5e9a4a7818 100644
@@ -44,7 +44,7 @@
 			  <&clks IMX7D_ENET1_TIME_ROOT_CLK>;
 	assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
 	assigned-clock-rates = <0>, <100000000>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-handle = <&ethphy0>;
 	fsl,magic-packet;
 	status = "okay";
@@ -70,7 +70,7 @@
 			  <&clks IMX7D_ENET2_TIME_ROOT_CLK>;
 	assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
 	assigned-clock-rates = <0>, <100000000>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-handle = <&ethphy1>;
 	fsl,magic-packet;
 	status = "okay";
Signature · 1 line
2.20.1
author maintainer
#98 lore raw

PATCH 91/203 arm64: dts: qcom: qcs404-evb: Mark WCSS clocks protected

In reply to Sasha Levin

From: Bjorn Andersson <[email protected]>

[ Upstream commit 54d895bea43c94f31304d59f82d755b7f4b59e7c ]

'7d0c76bdf227 ("clk: qcom: Add WCSS gcc clock control for QCS404")' introduces two new clocks to gcc. These are not used before clk_disable_unused() and as such the clock framework tries to disable them.

But on the EVB these registers are only accessible through TrustZone, so these clocks must be marked as "protected" to prevent the clock code from touching them.

Numerical values are used as the constants are not yet available in a common tree.

---
 arch/arm64/boot/dts/qcom/qcs404-evb.dtsi | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
arch/arm64/boot/dts/qcom/qcs404-evb.dtsi +3 -1
index 11c0a7137823d..db6df76e97a1a 100644
@@ -61,7 +61,9 @@
 	protected-clocks = <GCC_BIMC_CDSP_CLK>,
 			   <GCC_CDSP_CFG_AHB_CLK>,
 			   <GCC_CDSP_BIMC_CLK_SRC>,
-			   <GCC_CDSP_TBU_CLK>;
+			   <GCC_CDSP_TBU_CLK>,
+			   <141>, /* GCC_WCSS_Q6_AHB_CLK */
+			   <142>; /* GCC_WCSS_Q6_AXIM_CLK */
 };
 
 &pms405_spmi_regulators {
Signature · 1 line
2.20.1
author maintainer
#99 lore raw

PATCH 92/203 ARM: dts: imx7-colibri: disable HS400

In reply to Sasha Levin

From: Stefan Agner <[email protected]>

[ Upstream commit a95fbda08ee20cd063ce5826e0df95a2c22ea8c5 ]

Force HS200 by masking bit 63 of the SDHCI capability register. The i.MX ESDHC driver uses SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400. With that the stack checks bit 63 to descide whether HS400 is available. Using sdhci-caps-mask allows to mask bit 63. The stack then selects HS200 as operating mode.

This prevents rare communication errors with minimal effect on performance:

	sdhci-esdhc-imx 30b60000.usdhc: warning! HS400 strobe DLL
		status REF not lock!
---
 arch/arm/boot/dts/imx7-colibri.dtsi | 1 +
 1 file changed, 1 insertion(+)
arch/arm/boot/dts/imx7-colibri.dtsi +1 -0
index 895fbde4d4333..c1ed83131b495 100644
@@ -323,6 +323,7 @@
 	vmmc-supply = <&reg_module_3v3>;
 	vqmmc-supply = <&reg_DCDC3>;
 	non-removable;
+	sdhci-caps-mask = <0x80000000 0x0>;
 };
 
 &iomuxc {
Signature · 1 line
2.20.1
author maintainer
#127 lore raw

PATCH 120/203 ARM: OMAP2+: move platform-specific asm-offset.h to arch/arm/mach-omap2

In reply to Sasha Levin

From: Masahiro Yamada <[email protected]>

[ Upstream commit ccf4975dca233b1d6a74752d6ab35c239edc0d58 ]

<generated/ti-pm-asm-offsets.h> is only generated and included by arch/arm/mach-omap2/, so it does not need to reside in the globally visible include/generated/.

I renamed it to arch/arm/mach-omap2/pm-asm-offsets.h since the prefix 'ti-' is just redundant in mach-omap2/.

My main motivation of this change is to avoid the race condition for the parallel build (-j) when CONFIG_IKHEADERS is enabled.

When it is enabled, all the headers under include/ are archived into kernel/kheaders_data.tar.xz and exposed in the sysfs.

In the parallel build, we have no idea in which order files are built.

- If ti-pm-asm-offsets.h is built before kheaders_data.tar.xz, the header will be included in the archive. Probably nobody will use it, but it is harmless except that it will increase the archive size needlessly.

- If kheaders_data.tar.xz is built before ti-pm-asm-offsets.h, the header will not be included in the archive. However, in the next build, the archive will be re-generated to include the newly-found ti-pm-asm-offsets.h. This is not nice from the build system point of view.

- If ti-pm-asm-offsets.h and kheaders_data.tar.xz are built at the same time, the corrupted header might be included in the archive, which does not look nice either.

This commit fixes the race.

---
 arch/arm/mach-omap2/.gitignore  | 1 +
 arch/arm/mach-omap2/Makefile    | 5 +++--
 arch/arm/mach-omap2/sleep33xx.S | 2 +-
 arch/arm/mach-omap2/sleep43xx.S | 2 +-
 4 files changed, 6 insertions(+), 4 deletions(-)
 create mode 100644 arch/arm/mach-omap2/.gitignore
arch/arm/mach-omap2/.gitignore new file +1 -0
new file mode 100644
index 0000000000000..79a8d6ea71520
@@ -0,0 +1 @@
+pm-asm-offsets.h
arch/arm/mach-omap2/Makefile +3 -2
index 6006505516219..21c6d4bca3c0f 100644
@@ -223,9 +223,10 @@ obj-y					+= omap_phy_internal.o
 
 obj-$(CONFIG_MACH_OMAP2_TUSB6010)	+= usb-tusb6010.o
 
-include/generated/ti-pm-asm-offsets.h: arch/arm/mach-omap2/pm-asm-offsets.s FORCE
+$(obj)/pm-asm-offsets.h: $(obj)/pm-asm-offsets.s FORCE
 	$(call filechk,offsets,__TI_PM_ASM_OFFSETS_H__)
 
-$(obj)/sleep33xx.o $(obj)/sleep43xx.o: include/generated/ti-pm-asm-offsets.h
+$(obj)/sleep33xx.o $(obj)/sleep43xx.o: $(obj)/pm-asm-offsets.h
 
 targets += pm-asm-offsets.s
+clean-files += pm-asm-offsets.h
arch/arm/mach-omap2/sleep33xx.S +1 -1
index 68fee339d3f12..dc221249bc22c 100644
@@ -6,7 +6,6 @@
  *	Dave Gerlach, Vaibhav Bedia
  */
 
-#include <generated/ti-pm-asm-offsets.h>
 #include <linux/linkage.h>
 #include <linux/platform_data/pm33xx.h>
 #include <linux/ti-emif-sram.h>
@@ -15,6 +14,7 @@
 
 #include "iomap.h"
 #include "cm33xx.h"
+#include "pm-asm-offsets.h"
 
 #define AM33XX_CM_CLKCTRL_MODULESTATE_DISABLED			0x00030000
 #define AM33XX_CM_CLKCTRL_MODULEMODE_DISABLE			0x0003
arch/arm/mach-omap2/sleep43xx.S +1 -1
index c1f4e4852644e..90d2907a2eb27 100644
@@ -6,7 +6,6 @@
  *	Dave Gerlach, Vaibhav Bedia
  */
 
-#include <generated/ti-pm-asm-offsets.h>
 #include <linux/linkage.h>
 #include <linux/ti-emif-sram.h>
 #include <linux/platform_data/pm33xx.h>
@@ -19,6 +18,7 @@
 #include "iomap.h"
 #include "omap-secure.h"
 #include "omap44xx.h"
+#include "pm-asm-offsets.h"
 #include "prm33xx.h"
 #include "prcm43xx.h"
 
Signature · 1 line
2.20.1
author maintainer
#129 lore raw

PATCH 122/203 PM / devfreq: exynos-bus: Correct clock enable sequence

In reply to Sasha Levin

From: Kamil Konieczny <[email protected]>

[ Upstream commit 2c2b20e0da89c76759ee28c6824413ab2fa3bfc6 ]

Regulators should be enabled before clocks to avoid h/w hang. This require change in exynos_bus_probe() to move exynos_bus_parse_of() after exynos_bus_parent_parse_of() and change in error handling. Similar change is needed in exynos_bus_exit() where clock should be disabled before regulators.

---
 drivers/devfreq/exynos-bus.c | 31 +++++++++++++++++--------------
 1 file changed, 17 insertions(+), 14 deletions(-)
drivers/devfreq/exynos-bus.c +17 -14
index d9f377912c104..7c06df8bd74fe 100644
@@ -191,11 +191,10 @@ static void exynos_bus_exit(struct device *dev)
 	if (ret < 0)
 		dev_warn(dev, "failed to disable the devfreq-event devices\n");
 
-	if (bus->regulator)
-		regulator_disable(bus->regulator);
-
 	dev_pm_opp_of_remove_table(dev);
 	clk_disable_unprepare(bus->clk);
+	if (bus->regulator)
+		regulator_disable(bus->regulator);
 }
 
 /*
@@ -383,6 +382,7 @@ static int exynos_bus_probe(struct platform_device *pdev)
 	struct exynos_bus *bus;
 	int ret, max_state;
 	unsigned long min_freq, max_freq;
+	bool passive = false;
 
 	if (!np) {
 		dev_err(dev, "failed to find devicetree node\n");
@@ -396,27 +396,27 @@ static int exynos_bus_probe(struct platform_device *pdev)
 	bus->dev = &pdev->dev;
 	platform_set_drvdata(pdev, bus);
 
-	/* Parse the device-tree to get the resource information */
-	ret = exynos_bus_parse_of(np, bus);
-	if (ret < 0)
-		return ret;
-
 	profile = devm_kzalloc(dev, sizeof(*profile), GFP_KERNEL);
-	if (!profile) {
-		ret = -ENOMEM;
-		goto err;
-	}
+	if (!profile)
+		return -ENOMEM;
 
 	node = of_parse_phandle(dev->of_node, "devfreq", 0);
 	if (node) {
 		of_node_put(node);
-		goto passive;
+		passive = true;
 	} else {
 		ret = exynos_bus_parent_parse_of(np, bus);
+		if (ret < 0)
+			return ret;
 	}
 
+	/* Parse the device-tree to get the resource information */
+	ret = exynos_bus_parse_of(np, bus);
 	if (ret < 0)
-		goto err;
+		goto err_reg;
+
+	if (passive)
+		goto passive;
 
 	/* Initialize the struct profile and governor data for parent device */
 	profile->polling_ms = 50;
@@ -507,6 +507,9 @@ static int exynos_bus_probe(struct platform_device *pdev)
 err:
 	dev_pm_opp_of_remove_table(dev);
 	clk_disable_unprepare(bus->clk);
+err_reg:
+	if (!passive)
+		regulator_disable(bus->regulator);
 
 	return ret;
 }
Signature · 1 line
2.20.1
author maintainer
#143 lore raw

PATCH 136/203 arm64: dts: meson: fix boards regulators states format

In reply to Sasha Levin

From: Neil Armstrong <[email protected]>

[ Upstream commit f9717178b9be9477877d4c3776c61ff56d854ddf ]

This fixes the following DT schemas check errors:
meson-gxbb-odroidc2.dt.yaml: gpio-regulator-tf_io: states:0: Additional items are not allowed (1800000, 1 were unexpected) meson-gxbb-odroidc2.dt.yaml: gpio-regulator-tf_io: states:0: [3300000, 0, 1800000, 1] is too long meson-gxbb-nexbox-a95x.dt.yaml: gpio-regulator: states:0: Additional items are not allowed (3300000, 1 were unexpected) meson-gxbb-nexbox-a95x.dt.yaml: gpio-regulator: states:0: [1800000, 0, 3300000, 1] is too long meson-gxbb-p200.dt.yaml: gpio-regulator: states:0: Additional items are not allowed (3300000, 1 were unexpected) meson-gxbb-p200.dt.yaml: gpio-regulator: states:0: [1800000, 0, 3300000, 1] is too long meson-gxl-s905x-hwacom-amazetv.dt.yaml: gpio-regulator: states:0: Additional items are not allowed (3300000, 1 were unexpected) meson-gxl-s905x-hwacom-amazetv.dt.yaml: gpio-regulator: states:0: [1800000, 0, 3300000, 1] is too long meson-gxbb-p201.dt.yaml: gpio-regulator: states:0: Additional items are not allowed (3300000, 1 were unexpected) meson-gxbb-p201.dt.yaml: gpio-regulator: states:0: [1800000, 0, 3300000, 1] is too long meson-g12b-odroid-n2.dt.yaml: gpio-regulator-tf_io: states:0: Additional items are not allowed (1800000, 1 were unexpected) meson-g12b-odroid-n2.dt.yaml: gpio-regulator-tf_io: states:0: [3300000, 0, 1800000, 1] is too long meson-gxl-s905x-nexbox-a95x.dt.yaml: gpio-regulator: states:0: Additional items are not allowed (3300000, 1 were unexpected) meson-gxl-s905x-nexbox-a95x.dt.yaml: gpio-regulator: states:0: [1800000, 0, 3300000, 1] is too long

---
 arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts          | 4 ++--
 arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts        | 4 ++--
 arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts           | 4 ++--
 arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi              | 4 ++--
 .../arm64/boot/dts/amlogic/meson-gxl-s905x-hwacom-amazetv.dts | 4 ++--
 arch/arm64/boot/dts/amlogic/meson-gxl-s905x-nexbox-a95x.dts   | 4 ++--
 6 files changed, 12 insertions(+), 12 deletions(-)
arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts +2 -2
index 4e916e1f71f76..1c2a9ca491c02 100644
@@ -66,8 +66,8 @@
 		gpios = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_HIGH>;
 		gpios-states = <0>;
 
-		states = <3300000 0
-			  1800000 1>;
+		states = <3300000 0>,
+			 <1800000 1>;
 	};
 
 	flash_1v8: regulator-flash_1v8 {
arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts +2 -2
index b636912a27157..afcf8a9f667b9 100644
@@ -75,8 +75,8 @@
 		gpios-states = <1>;
 
 		/* Based on P200 schematics, signal CARD_1.8V/3.3V_CTR */
-		states = <1800000 0
-			  3300000 1>;
+		states = <1800000 0>,
+			 <3300000 1>;
 	};
 
 	vddio_boot: regulator-vddio_boot {
arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts +2 -2
index 9972b1515da61..6039adda12eec 100644
@@ -77,8 +77,8 @@
 		gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_HIGH>;
 		gpios-states = <0>;
 
-		states = <3300000 0
-			  1800000 1>;
+		states = <3300000 0>,
+			 <1800000 1>;
 	};
 
 	vcc1v8: regulator-vcc1v8 {
arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi +2 -2
index e8f925871edfc..89f7b41b0e9ef 100644
@@ -46,8 +46,8 @@
 		gpios-states = <1>;
 
 		/* Based on P200 schematics, signal CARD_1.8V/3.3V_CTR */
-		states = <1800000 0
-			  3300000 1>;
+		states = <1800000 0>,
+			 <3300000 1>;
 
 		regulator-settling-time-up-us = <10000>;
 		regulator-settling-time-down-us = <150000>;
arch/arm64/boot/dts/amlogic/meson-gxl-s905x-hwacom-amazetv.dts +2 -2
index 796baea7a0bfb..c8d74e61dec18 100644
@@ -38,8 +38,8 @@
 		gpios-states = <1>;
 
 		/* Based on P200 schematics, signal CARD_1.8V/3.3V_CTR */
-		states = <1800000 0
-			  3300000 1>;
+		states = <1800000 0>,
+			 <3300000 1>;
 	};
 
 	vddio_boot: regulator-vddio_boot {
arch/arm64/boot/dts/amlogic/meson-gxl-s905x-nexbox-a95x.dts +2 -2
index 26907ac829301..c433a031841f6 100644
@@ -38,8 +38,8 @@
 		gpios-states = <1>;
 
 		/* Based on P200 schematics, signal CARD_1.8V/3.3V_CTR */
-		states = <1800000 0
-			  3300000 1>;
+		states = <1800000 0>,
+			 <3300000 1>;
 	};
 
 	vddio_boot: regulator-vddio_boot {
Signature · 1 line
2.20.1
author maintainer
#161 lore raw

PATCH 154/203 ASoC: dt-bindings: sun4i-spdif: Fix dma-names warning

In reply to Sasha Levin

From: Maxime Ripard <[email protected]>

[ Upstream commit 1a8e7cdfa4f5872bf0c202d09bff6628aba6b9f6 ]

Even though the H6 compatible has been properly added, the exeption for the number of DMA channels hasn't been updated, leading in a validation warning.

Fix this.

Fixes b20453031472 ("dt-bindings: sound: sun4i-spdif: Add Allwinner H6 compatible")
---
 .../devicetree/bindings/sound/allwinner,sun4i-a10-spdif.yaml  | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/sound/allwinner,sun4i-a10-spdif.yaml +3 -1
index e0284d8c3b636..38d4cede0860d 100644
@@ -70,7 +70,9 @@ allOf:
       properties:
         compatible:
           contains:
-            const: allwinner,sun8i-h3-spdif
+            enum:
+              - allwinner,sun8i-h3-spdif
+              - allwinner,sun50i-h6-spdif
 
     then:
       properties:
Signature · 1 line
2.20.1
author maintainer
#162 lore raw

PATCH 155/203 ARM: dts: exynos: Mark LDO10 as always-on on Peach Pit/Pi Chromebooks

In reply to Sasha Levin

From: Marek Szyprowski <[email protected]>

[ Upstream commit 5b0eeeaa37615df37a9a30929b73e9defe61ca84 ]

Commit aff138bf8e37 ("ARM: dts: exynos: Add TMU nodes regulator supply for Peach boards") assigned LDO10 to Exynos Thermal Measurement Unit, but it turned out that it supplies also some other critical parts and board freezes/crashes when it is turned off.

The mentioned commit made Exynos TMU a consumer of that regulator and in typical case Exynos TMU driver keeps it enabled from early boot. However there are such configurations (example is multi_v7_defconfig), in which some of the regulators are compiled as modules and are not available from early boot. In such case it may happen that LDO10 is turned off by regulator core, because it has no consumers yet (in this case consumer drivers cannot get it, because the supply regulators for it are not yet available). This in turn causes the board to crash. This patch restores 'always-on' property for the LDO10 regulator.

Fixes aff138bf8e37 ("ARM: dts: exynos: Add TMU nodes regulator supply for Peach boards")
---
 arch/arm/boot/dts/exynos5420-peach-pit.dts | 1 +
 arch/arm/boot/dts/exynos5800-peach-pi.dts  | 1 +
 2 files changed, 2 insertions(+)
arch/arm/boot/dts/exynos5420-peach-pit.dts +1 -0
index f78db6809cca4..9eb48cabcca45 100644
@@ -440,6 +440,7 @@
 				regulator-name = "vdd_ldo10";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
 				regulator-state-mem {
 					regulator-off-in-suspend;
 				};
arch/arm/boot/dts/exynos5800-peach-pi.dts +1 -0
index e0f470fe54c81..4398f2d1fe881 100644
@@ -440,6 +440,7 @@
 				regulator-name = "vdd_ldo10";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
 				regulator-state-mem {
 					regulator-off-in-suspend;
 				};
Signature · 1 line
2.20.1
author maintainer
#166 lore raw

PATCH 159/203 closures: fix a race on wakeup from closure_sync

In reply to Sasha Levin

From: Kent Overstreet <[email protected]>

[ Upstream commit a22a9602b88fabf10847f238ff81fde5f906fef7 ]

The race was when a thread using closure_sync() notices cl->s->done == 1 before the thread calling closure_put() calls wake_up_process(). Then, it's possible for that thread to return and exit just before wake_up_process() is called - so we're trying to wake up a process that no longer exists.

rcu_read_lock() is sufficient to protect against this, as there's an rcu barrier somewhere in the process teardown path.

---
 drivers/md/bcache/closure.c | 10 ++++++++--
 1 file changed, 8 insertions(+), 2 deletions(-)
drivers/md/bcache/closure.c +8 -2
index 73f5319295bc9..c12cd809ab193 100644
@@ -105,8 +105,14 @@ struct closure_syncer {
 
 static void closure_sync_fn(struct closure *cl)
 {
-	cl->s->done = 1;
-	wake_up_process(cl->s->task);
+	struct closure_syncer *s = cl->s;
+	struct task_struct *p;
+
+	rcu_read_lock();
+	p = READ_ONCE(s->task);
+	s->done = 1;
+	wake_up_process(p);
+	rcu_read_unlock();
 }
 
 void __sched __closure_sync(struct closure *cl)
Signature · 1 line
2.20.1
author maintainer
#169 lore raw

PATCH 162/203 md/raid1: fail run raid1 array when active disk less than one

In reply to Sasha Levin

From: Yufen Yu <[email protected]>

[ Upstream commit 07f1a6850c5d5a65c917c3165692b5179ac4cb6b ]

When run test case:
mdadm -CR /dev/md1 -l 1 -n 4 /dev/sd[a-d] --assume-clean --bitmap=internal mdadm -S /dev/md1
mdadm -A /dev/md1 /dev/sd[b-c] --run --force

  mdadm --zero /dev/sda
  mdadm /dev/md1 -a /dev/sda

echo offline > /sys/block/sdc/device/state
echo offline > /sys/block/sdb/device/state
sleep 5
mdadm -S /dev/md1

  echo running > /sys/block/sdb/device/state
  echo running > /sys/block/sdc/device/state
  mdadm -A /dev/md1 /dev/sd[a-c] --run --force

mdadm run fail with kernel message as follow:

[  172.986064] md: kicking non-fresh sdb from array!
[  173.004210] md: kicking non-fresh sdc from array!
[  173.022383] md/raid1:md1: active with 0 out of 4 mirrors
[  173.022406] md1: failed to create bitmap (-5)

In fact, when active disk in raid1 array less than one, we need to return fail in raid1_run().

---
 drivers/md/raid1.c | 13 ++++++++++++-
 1 file changed, 12 insertions(+), 1 deletion(-)
drivers/md/raid1.c +12 -1
index 501a3b4d82f33..5afbb7df06e70 100644
@@ -3129,6 +3129,13 @@ static int raid1_run(struct mddev *mddev)
 		    !test_bit(In_sync, &conf->mirrors[i].rdev->flags) ||
 		    test_bit(Faulty, &conf->mirrors[i].rdev->flags))
 			mddev->degraded++;
+	/*
+	 * RAID1 needs at least one disk in active
+	 */
+	if (conf->raid_disks - mddev->degraded < 1) {
+		ret = -EINVAL;
+		goto abort;
+	}
 
 	if (conf->raid_disks - mddev->degraded == 1)
 		mddev->recovery_cp = MaxSector;
@@ -3162,8 +3169,12 @@ static int raid1_run(struct mddev *mddev)
 	ret = md_integrity_register(mddev);
 	if (ret) {
 		md_unregister_thread(&mddev->thread);
-		raid1_free(mddev, conf);
+		goto abort;
 	}
+	return 0;
+
+abort:
+	raid1_free(mddev, conf);
 	return ret;
 }
 
Signature · 1 line
2.20.1
author maintainer
#176 lore raw

PATCH 169/203 x86/platform/uv: Fix kmalloc() NULL check routine

In reply to Sasha Levin

From: Austin Kim <[email protected]>

[ Upstream commit 864b23f0169d5bff677e8443a7a90dfd6b090afc ]

The result of kmalloc() should have been checked ahead of below statement:

	pqp = (struct bau_pq_entry *)vp;

Move BUG_ON(!vp) before above statement.

---
 arch/x86/platform/uv/tlb_uv.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
arch/x86/platform/uv/tlb_uv.c +2 -2
index 20c389a91b803..5f0a96bf27a1f 100644
@@ -1804,9 +1804,9 @@ static void pq_init(int node, int pnode)
 
 	plsize = (DEST_Q_SIZE + 1) * sizeof(struct bau_pq_entry);
 	vp = kmalloc_node(plsize, GFP_KERNEL, node);
-	pqp = (struct bau_pq_entry *)vp;
-	BUG_ON(!pqp);
+	BUG_ON(!vp);
 
+	pqp = (struct bau_pq_entry *)vp;
 	cp = (char *)pqp + 31;
 	pqp = (struct bau_pq_entry *)(((unsigned long)cp >> 5) << 5);
 
Signature · 1 line
2.20.1
author maintainer
#182 lore raw

PATCH 171/203 platform/x86: intel_pmc_core: Do not ioremap RAM

In reply to Sasha Levin

From: "M. Vefa Bicakci" <[email protected]>

[ Upstream commit 7d505758b1e556cdf65a5e451744fe0ae8063d17 ]

On a Xen-based PVH virtual machine with more than 4 GiB of RAM, intel_pmc_core fails initialization with the following warning message from the kernel, indicating that the driver is attempting to ioremap RAM:

ioremap on RAM at 0x00000000fe000000 - 0x00000000fe001fff

  WARNING: CPU: 1 PID: 434 at arch/x86/mm/ioremap.c:186 __ioremap_caller.constprop.0+0x2aa/0x2c0
...
  Call Trace:
   ? pmc_core_probe+0x87/0x2d0 [intel_pmc_core]
   pmc_core_probe+0x87/0x2d0 [intel_pmc_core]

This issue appears to manifest itself because of the following fallback mechanism in the driver:

	if (lpit_read_residency_count_address(&slp_s0_addr))
		pmcdev->base_addr = PMC_BASE_ADDR_DEFAULT;

The validity of address PMC_BASE_ADDR_DEFAULT (i.e., 0xFE000000) is not verified by the driver, which is what this patch introduces. With this patch, if address PMC_BASE_ADDR_DEFAULT is in RAM, then the driver will not attempt to ioremap the aforementioned address.

---
 drivers/platform/x86/intel_pmc_core.c | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)
drivers/platform/x86/intel_pmc_core.c +6 -2
index c510d0d724759..3b6b8dcc47678 100644
@@ -878,10 +878,14 @@ static int pmc_core_probe(struct platform_device *pdev)
 	if (pmcdev->map == &spt_reg_map && !pci_dev_present(pmc_pci_ids))
 		pmcdev->map = &cnp_reg_map;
 
-	if (lpit_read_residency_count_address(&slp_s0_addr))
+	if (lpit_read_residency_count_address(&slp_s0_addr)) {
 		pmcdev->base_addr = PMC_BASE_ADDR_DEFAULT;
-	else
+
+		if (page_is_ram(PHYS_PFN(pmcdev->base_addr)))
+			return -ENODEV;
+	} else {
 		pmcdev->base_addr = slp_s0_addr - pmcdev->map->slp_s0_offset;
+	}
 
 	pmcdev->regbase = ioremap(pmcdev->base_addr,
 				  pmcdev->map->regmap_length);
Signature · 1 line
2.20.1
author maintainer
#183 lore raw

PATCH 172/203 platform/x86: intel_pmc_core_pltdrv: Module removal warning fix

In reply to Sasha Levin

From: "M. Vefa Bicakci" <[email protected]>

[ Upstream commit 0b43e41e93815ecd9616759cf5d64d3a7be8e6fb ]

Prior to this commit, removing the intel_pmc_core_pltdrv module would cause the following warning:

Device 'intel_pmc_core.0' does not have a release() function, it is broken and must be fixed. See Documentation/kobject.txt.

  WARNING: CPU: 0 PID: 2202 at drivers/base/core.c:1238 device_release+0x6f/0x80

This commit hence adds an empty release function for the driver.

---
 drivers/platform/x86/intel_pmc_core_pltdrv.c | 8 ++++++++
 1 file changed, 8 insertions(+)
drivers/platform/x86/intel_pmc_core_pltdrv.c +8 -0
index a8754a6db1b8b..186540014c480 100644
@@ -18,8 +18,16 @@
 #include <asm/cpu_device_id.h>
 #include <asm/intel-family.h>
 
+static void intel_pmc_core_release(struct device *dev)
+{
+	/* Nothing to do. */
+}
+
 static struct platform_device pmc_core_device = {
 	.name = "intel_pmc_core",
+	.dev  = {
+		.release = intel_pmc_core_release,
+	},
 };
 
 /*
Signature · 1 line
2.20.1
author maintainer
#190 lore raw

PATCH 177/203 spi: bcm2835: Work around DONE bit erratum

In reply to Sasha Levin

From: Lukas Wunner <[email protected]>

[ Upstream commit 4c524191c0a21d758b519087c64f84348095e940 ]

Commit 3bd7f6589f67 ("spi: bcm2835: Overcome sglist entry length limitation") amended the BCM2835 SPI driver with support for DMA transfers whose buffers are not aligned to 4 bytes and require more than one sglist entry.

When testing this feature with upcoming commits to speed up TX-only and RX-only transfers, I noticed that SPI transmission sometimes breaks. A function introduced by the commit, bcm2835_spi_transfer_prologue(), performs one or two PIO transmissions as a prologue to the actual DMA transmission. It turns out that the breakage goes away if the DONE bit in the CS register is set when ending such a PIO transmission.

The DONE bit signifies emptiness of the TX FIFO. According to the spec, the bit is of type RO, so writing it should never have any effect. Perhaps the spec is wrong and the bit is actually of type RW1C. E.g. the I2C controller on the BCM2835 does have an RW1C DONE bit which needs to be cleared by the driver. Another, possibly more likely explanation is that it's a hardware erratum since the issue does not occur consistently.

Either way, amend bcm2835_spi_transfer_prologue() to always write the DONE bit.

Usually a transmission is ended by bcm2835_spi_reset_hw(). If the transmission was successful, the TX FIFO is empty and thus the DONE bit is set when bcm2835_spi_reset_hw() reads the CS register. The bit is then written back to the register, so we happen to do the right thing.

However if DONE is not set, e.g. because transmission is aborted with a non-empty TX FIFO, the bit won't be written by bcm2835_spi_reset_hw() and it seems possible that transmission might subsequently break. To be on the safe side, likewise amend bcm2835_spi_reset_hw() to always write the bit.

---
 drivers/spi/spi-bcm2835.c | 14 ++++++++++++--
 1 file changed, 12 insertions(+), 2 deletions(-)
drivers/spi/spi-bcm2835.c +12 -2
index 840b1b8ff3dcb..dfdcebb38830a 100644
@@ -319,6 +319,13 @@ static void bcm2835_spi_reset_hw(struct spi_controller *ctlr)
 		BCM2835_SPI_CS_INTD |
 		BCM2835_SPI_CS_DMAEN |
 		BCM2835_SPI_CS_TA);
+	/*
+	 * Transmission sometimes breaks unless the DONE bit is written at the
+	 * end of every transfer.  The spec says it's a RO bit.  Either the
+	 * spec is wrong and the bit is actually of type RW1C, or it's a
+	 * hardware erratum.
+	 */
+	cs |= BCM2835_SPI_CS_DONE;
 	/* and reset RX/TX FIFOS */
 	cs |= BCM2835_SPI_CS_CLEAR_RX | BCM2835_SPI_CS_CLEAR_TX;
 
@@ -477,7 +484,9 @@ static void bcm2835_spi_transfer_prologue(struct spi_controller *ctlr,
 		bcm2835_wr_fifo_count(bs, bs->rx_prologue);
 		bcm2835_wait_tx_fifo_empty(bs);
 		bcm2835_rd_fifo_count(bs, bs->rx_prologue);
-		bcm2835_spi_reset_hw(ctlr);
+		bcm2835_wr(bs, BCM2835_SPI_CS, cs | BCM2835_SPI_CS_CLEAR_RX
+						  | BCM2835_SPI_CS_CLEAR_TX
+						  | BCM2835_SPI_CS_DONE);
 
 		dma_sync_single_for_device(ctlr->dma_rx->device->dev,
 					   sg_dma_address(&tfr->rx_sg.sgl[0]),
@@ -498,7 +507,8 @@ static void bcm2835_spi_transfer_prologue(struct spi_controller *ctlr,
 						  | BCM2835_SPI_CS_DMAEN);
 		bcm2835_wr_fifo_count(bs, tx_remaining);
 		bcm2835_wait_tx_fifo_empty(bs);
-		bcm2835_wr(bs, BCM2835_SPI_CS, cs | BCM2835_SPI_CS_CLEAR_TX);
+		bcm2835_wr(bs, BCM2835_SPI_CS, cs | BCM2835_SPI_CS_CLEAR_TX
+						  | BCM2835_SPI_CS_DONE);
 	}
 
 	if (likely(!bs->tx_spillover)) {
Signature · 1 line
2.20.1
author maintainer
#193 lore raw

PATCH 180/203 raid5: don't set STRIPE_HANDLE to stripe which is in batch list

In reply to Sasha Levin

From: Guoqing Jiang <[email protected]>

[ Upstream commit 6ce220dd2f8ea71d6afc29b9a7524c12e39f374a ]

If stripe in batch list is set with STRIPE_HANDLE flag, then the stripe could be set with STRIPE_ACTIVE by the handle_stripe function. And if error happens to the batch_head at the same time, break_stripe_batch_list is called, then below warning could happen (the same report in [1]), it means a member of batch list was set with STRIPE_ACTIVE.

[7028915.431770] stripe state: 2001
[7028915.431815] ------------[ cut here ]------------
[7028915.431828] WARNING: CPU: 18 PID: 29089 at drivers/md/raid5.c:4614 break_stripe_batch_list+0x203/0x240 [raid456]
[...]
[7028915.431879] CPU: 18 PID: 29089 Comm: kworker/u82:5 Tainted: G           O    4.14.86-1-storage #4.14.86-1.2~deb9
[7028915.431881] Hardware name: Supermicro SSG-2028R-ACR24L/X10DRH-iT, BIOS 3.1 06/18/2018
[7028915.431888] Workqueue: raid5wq raid5_do_work [raid456]
[7028915.431890] task: ffff9ab0ef36d7c0 task.stack: ffffb72926f84000
[7028915.431896] RIP: 0010:break_stripe_batch_list+0x203/0x240 [raid456]
[7028915.431898] RSP: 0018:ffffb72926f87ba8 EFLAGS: 00010286
[7028915.431900] RAX: 0000000000000012 RBX: ffff9aaa84a98000 RCX: 0000000000000000
[7028915.431901] RDX: 0000000000000000 RSI: ffff9ab2bfa15458 RDI: ffff9ab2bfa15458
[7028915.431902] RBP: ffff9aaa8fb4e900 R08: 0000000000000001 R09: 0000000000002eb4
[7028915.431903] R10: 00000000ffffffff R11: 0000000000000000 R12: ffff9ab1736f1b00
[7028915.431904] R13: 0000000000000000 R14: ffff9aaa8fb4e900 R15: 0000000000000001
[7028915.431906] FS:  0000000000000000(0000) GS:ffff9ab2bfa00000(0000) knlGS:0000000000000000
[7028915.431907] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[7028915.431908] CR2: 00007ff953b9f5d8 CR3: 0000000bf4009002 CR4: 00000000003606e0
[7028915.431909] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[7028915.431910] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[7028915.431910] Call Trace:
[7028915.431923]  handle_stripe+0x8e7/0x2020 [raid456]
[7028915.431930]  ? __wake_up_common_lock+0x89/0xc0
[7028915.431935]  handle_active_stripes.isra.58+0x35f/0x560 [raid456]
[7028915.431939]  raid5_do_work+0xc6/0x1f0 [raid456]

Also commit 59fc630b8b5f9f ("RAID5: batch adjacent full stripe write") said "If a stripe is added to batch list, then only the first stripe of the list should be put to handle_list and run handle_stripe."

So don't set STRIPE_HANDLE to stripe which is already in batch list, otherwise the stripe could be put to handle_list and run handle_stripe, then the above warning could be triggered.

[1]. https://www.spinics.net/lists/raid/msg62552.html

---
 drivers/md/raid5.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/md/raid5.c +2 -1
index 3de4e13bde984..21514edb2bea3 100644
@@ -5718,7 +5718,8 @@ static bool raid5_make_request(struct mddev *mddev, struct bio * bi)
 				do_flush = false;
 			}
 
-			set_bit(STRIPE_HANDLE, &sh->state);
+			if (!sh->batch_head)
+				set_bit(STRIPE_HANDLE, &sh->state);
 			clear_bit(STRIPE_DELAYED, &sh->state);
 			if ((!sh->batch_head || sh == sh->batch_head) &&
 			    (bi->bi_opf & REQ_SYNC) &&
Signature · 1 line
2.20.1
author maintainer
#194 lore raw

PATCH 181/203 mmc: core: Clarify sdio_irq_pending flag for MMC_CAP2_SDIO_IRQ_NOTHREAD

In reply to Sasha Levin

From: Ulf Hansson <[email protected]>

[ Upstream commit 36d57efb4af534dd6b442ea0b9a04aa6dfa37abe ]

The sdio_irq_pending flag is used to let host drivers indicate that it has signaled an IRQ. If that is the case and we only have a single SDIO func that have claimed an SDIO IRQ, our assumption is that we can avoid reading the SDIO_CCCR_INTx register and just call the SDIO func irq handler immediately. This makes sense, but the flag is set/cleared in a somewhat messy order, let's fix that up according to below.

First, the flag is currently set in sdio_run_irqs(), which is executed as a work that was scheduled from sdio_signal_irq(). To make it more implicit that the host have signaled an IRQ, let's instead immediately set the flag in sdio_signal_irq(). This also makes the behavior consistent with host drivers that uses the legacy, mmc_signal_sdio_irq() API. This have no functional impact, because we don't expect host drivers to call sdio_signal_irq() until after the work (sdio_run_irqs()) have been executed anyways.

Second, currently we never clears the flag when using the sdio_run_irqs() work, but only when using the sdio_irq_thread(). Let make the behavior consistent, by moving the flag to be cleared inside the common process_sdio_pending_irqs() function. Additionally, tweak the behavior of the flag slightly, by avoiding to clear it unless we processed the SDIO IRQ. The purpose with this at this point, is to keep the information about whether there have been an SDIO IRQ signaled by the host, so at system resume we can decide to process it without reading the SDIO_CCCR_INTx register.

---
 drivers/mmc/core/sdio_irq.c | 9 ++++++---
 1 file changed, 6 insertions(+), 3 deletions(-)
drivers/mmc/core/sdio_irq.c +6 -3
index 0bcc5e83bd1a0..40109a6159228 100644
@@ -31,6 +31,7 @@ static int process_sdio_pending_irqs(struct mmc_host *host)
 {
 	struct mmc_card *card = host->card;
 	int i, ret, count;
+	bool sdio_irq_pending = host->sdio_irq_pending;
 	unsigned char pending;
 	struct sdio_func *func;
 
@@ -38,13 +39,16 @@ static int process_sdio_pending_irqs(struct mmc_host *host)
 	if (mmc_card_suspended(card))
 		return 0;
 
+	/* Clear the flag to indicate that we have processed the IRQ. */
+	host->sdio_irq_pending = false;
+
 	/*
 	 * Optimization, if there is only 1 function interrupt registered
 	 * and we know an IRQ was signaled then call irq handler directly.
 	 * Otherwise do the full probe.
 	 */
 	func = card->sdio_single_irq;
-	if (func && host->sdio_irq_pending) {
+	if (func && sdio_irq_pending) {
 		func->irq_handler(func);
 		return 1;
 	}
@@ -96,7 +100,6 @@ static void sdio_run_irqs(struct mmc_host *host)
 {
 	mmc_claim_host(host);
 	if (host->sdio_irqs) {
-		host->sdio_irq_pending = true;
 		process_sdio_pending_irqs(host);
 		if (host->ops->ack_sdio_irq)
 			host->ops->ack_sdio_irq(host);
@@ -114,6 +117,7 @@ void sdio_irq_work(struct work_struct *work)
 
 void sdio_signal_irq(struct mmc_host *host)
 {
+	host->sdio_irq_pending = true;
 	queue_delayed_work(system_wq, &host->sdio_irq_work, 0);
 }
 EXPORT_SYMBOL_GPL(sdio_signal_irq);
@@ -159,7 +163,6 @@ static int sdio_irq_thread(void *_host)
 		if (ret)
 			break;
 		ret = process_sdio_pending_irqs(host);
-		host->sdio_irq_pending = false;
 		mmc_release_host(host);
 
 		/*
Signature · 1 line
2.20.1
author maintainer
#195 lore raw

PATCH 182/203 sched/psi: Correct overly pessimistic size calculation

In reply to Sasha Levin

From: Miles Chen <miles.chen-NuS5LvNUpcJWk0Htik3J/[email protected]>

[ Upstream commit 4adcdcea717cb2d8436bef00dd689aa5bc76f11b ]

When passing a equal or more then 32 bytes long string to psi_write(), psi_write() copies 31 bytes to its buf and overwrites buf[30] with '\0'. Which makes the input string 1 byte shorter than it should be.

Fix it by copying sizeof(buf) bytes when nbytes >= sizeof(buf).

This does not cause problems in normal use case like:
"some 500000 10000000" or "full 500000 10000000" because they are less than 32 bytes in length.

	/* assuming nbytes == 35 */
	char buf[32];

	buf_size = min(nbytes, (sizeof(buf) - 1)); /* buf_size = 31 */
	if (copy_from_user(buf, user_buf, buf_size))
		return -EFAULT;

	buf[buf_size - 1] = '\0'; /* buf[30] = '\0' */

Before:

%cd /proc/pressure/
%echo "123456789|123456789|123456789|1234" > memory

 [   22.473497] nbytes=35,buf_size=31
 [   22.473775] 123456789|123456789|123456789| (print 30 chars)
 %sh: write error: Invalid argument

%echo "123456789|123456789|123456789|1" > memory

 [   64.916162] nbytes=32,buf_size=31
 [   64.916331] 123456789|123456789|123456789| (print 30 chars)
 %sh: write error: Invalid argument

After:

%cd /proc/pressure/
%echo "123456789|123456789|123456789|1234" > memory

 [  254.837863] nbytes=35,buf_size=32
 [  254.838541] 123456789|123456789|123456789|1 (print 31 chars)
 %sh: write error: Invalid argument

%echo "123456789|123456789|123456789|1" > memory

 [ 9965.714935] nbytes=32,buf_size=32
 [ 9965.715096] 123456789|123456789|123456789|1 (print 31 chars)
 %sh: write error: Invalid argument

Also remove the superfluous parentheses.

---
 kernel/sched/psi.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
kernel/sched/psi.c +1 -1
index 6e52b67b420e7..517e3719027e6 100644
@@ -1198,7 +1198,7 @@ static ssize_t psi_write(struct file *file, const char __user *user_buf,
 	if (static_branch_likely(&psi_disabled))
 		return -EOPNOTSUPP;
 
-	buf_size = min(nbytes, (sizeof(buf) - 1));
+	buf_size = min(nbytes, sizeof(buf));
 	if (copy_from_user(buf, user_buf, buf_size))
 		return -EFAULT;
 
Signature · 1 line
2.20.1
author maintainer
#196 lore raw

PATCH 183/203 mmc: sdhci: Fix incorrect switch to HS mode

In reply to Sasha Levin

From: Al Cooper <[email protected]>

[ Upstream commit c894e33ddc1910e14d6f2a2016f60ab613fd8b37 ]

When switching from any MMC speed mode that requires 1.8v (HS200, HS400 and HS400ES) to High Speed (HS) mode, the system ends up configured for SDR12 with a 50MHz clock which is an illegal mode.

This happens because the SDHCI_CTRL_VDD_180 bit in the SDHCI_HOST_CONTROL2 register is left set and when this bit is set, the speed mode is controlled by the SDHCI_CTRL_UHS field in the SDHCI_HOST_CONTROL2 register. The SDHCI_CTRL_UHS field will end up being set to 0 (SDR12) by sdhci_set_uhs_signaling() because there is no UHS mode being set.

The fix is to change sdhci_set_uhs_signaling() to set the SDHCI_CTRL_UHS field to SDR25 (which is the same as HS) for any switch to HS mode.

This was found on a new eMMC controller that does strict checking of the speed mode and the corresponding clock rate. It caused the switch to HS400 mode to fail because part of the sequence to switch to HS400 requires a switch from HS200 to HS before going to HS400.

---
 drivers/mmc/host/sdhci.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/mmc/host/sdhci.c +3 -1
index a5dc5aae973e6..c66e66fbaeb40 100644
@@ -1849,7 +1849,9 @@ void sdhci_set_uhs_signaling(struct sdhci_host *host, unsigned timing)
 		ctrl_2 |= SDHCI_CTRL_UHS_SDR104;
 	else if (timing == MMC_TIMING_UHS_SDR12)
 		ctrl_2 |= SDHCI_CTRL_UHS_SDR12;
-	else if (timing == MMC_TIMING_UHS_SDR25)
+	else if (timing == MMC_TIMING_SD_HS ||
+		 timing == MMC_TIMING_MMC_HS ||
+		 timing == MMC_TIMING_UHS_SDR25)
 		ctrl_2 |= SDHCI_CTRL_UHS_SDR25;
 	else if (timing == MMC_TIMING_UHS_SDR50)
 		ctrl_2 |= SDHCI_CTRL_UHS_SDR50;
Signature · 1 line
2.20.1
author maintainer
#197 lore raw

PATCH 184/203 mmc: core: Add helper function to indicate if SDIO IRQs is enabled

In reply to Sasha Levin

From: Ulf Hansson <[email protected]>

[ Upstream commit bd880b00697befb73eff7220ee20bdae4fdd487b ]

To avoid each host driver supporting SDIO IRQs, from keeping track internally about if SDIO IRQs has been claimed, let's introduce a common helper function, sdio_irq_claimed().

The function returns true if SDIO IRQs are claimed, via using the information about the number of claimed irqs. This is safe, even without any locks, as long as the helper function is called only from runtime/system suspend callbacks of the host driver.

---
 include/linux/mmc/host.h | 9 +++++++++
 1 file changed, 9 insertions(+)
include/linux/mmc/host.h +9 -0
index 4a351cb7f20fc..cf87c673cbb81 100644
@@ -493,6 +493,15 @@ void mmc_command_done(struct mmc_host *host, struct mmc_request *mrq);
 
 void mmc_cqe_request_done(struct mmc_host *host, struct mmc_request *mrq);
 
+/*
+ * May be called from host driver's system/runtime suspend/resume callbacks,
+ * to know if SDIO IRQs has been claimed.
+ */
+static inline bool sdio_irq_claimed(struct mmc_host *host)
+{
+	return host->sdio_irqs > 0;
+}
+
 static inline void mmc_signal_sdio_irq(struct mmc_host *host)
 {
 	host->ops->enable_sdio_irq(host, 0);
Signature · 1 line
2.20.1
author maintainer
#198 lore raw

PATCH 185/203 mmc: dw_mmc: Re-store SDIO IRQs mask at system resume

In reply to Sasha Levin

From: Ulf Hansson <[email protected]>

[ Upstream commit 7c526608d5afb62cbc967225e2ccaacfdd142e9d ]

In cases when SDIO IRQs have been enabled, runtime suspend is prevented by the driver. However, this still means dw_mci_runtime_suspend|resume() gets called during system suspend/resume, via pm_runtime_force_suspend|resume(). This means during system suspend/resume, the register context of the dw_mmc device most likely loses its register context, even in cases when SDIO IRQs have been enabled.

To re-enable the SDIO IRQs during system resume, the dw_mmc driver currently relies on the mmc core to re-enable the SDIO IRQs when it resumes the SDIO card, but this isn't the recommended solution. Instead, it's better to deal with this locally in the dw_mmc driver, so let's do that.

---
 drivers/mmc/host/dw_mmc.c | 4 ++++
 1 file changed, 4 insertions(+)
drivers/mmc/host/dw_mmc.c +4 -0
index eea52e2c5a0ce..79c55c7b4afd9 100644
@@ -3460,6 +3460,10 @@ int dw_mci_runtime_resume(struct device *dev)
 	/* Force setup bus to guarantee available clock output */
 	dw_mci_setup_bus(host->slot, true);
 
+	/* Re-enable SDIO interrupts. */
+	if (sdio_irq_claimed(host->slot->mmc))
+		__dw_mci_enable_sdio_irq(host->slot, 1);
+
 	/* Now that slots are all setup, we can enable card detect */
 	dw_mci_enable_cd(host);
 
Signature · 1 line
2.20.1
author maintainer
#199 lore raw

PATCH 186/203 raid5: don't increment read_errors on EILSEQ return

In reply to Sasha Levin

From: Nigel Croxon <[email protected]>

[ Upstream commit b76b4715eba0d0ed574f58918b29c1b2f0fa37a8 ]

While MD continues to count read errors returned by the lower layer. If those errors are -EILSEQ, instead of -EIO, it should NOT increase the read_errors count.

When RAID6 is set up on dm-integrity target that detects massive corruption, the leg will be ejected from the array. Even if the issue is correctable with a sector re-write and the array has necessary redundancy to correct it.

The leg is ejected because it runs up the rdev->read_errors beyond conf->max_nr_stripes. The return status in dm-drypt when there is a data integrity error is -EILSEQ (BLK_STS_PROTECTION).

---
 drivers/md/raid5.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/md/raid5.c +2 -1
index 21514edb2bea3..d574701185db9 100644
@@ -2526,7 +2526,8 @@ static void raid5_end_read_request(struct bio * bi)
 		int set_bad = 0;
 
 		clear_bit(R5_UPTODATE, &sh->dev[i].flags);
-		atomic_inc(&rdev->read_errors);
+		if (!(bi->bi_status == BLK_STS_PROTECTION))
+			atomic_inc(&rdev->read_errors);
 		if (test_bit(R5_ReadRepl, &sh->dev[i].flags))
 			pr_warn_ratelimited(
 				"md/raid:%s: read error on replacement device (sector %llu on %s).\n",
Signature · 1 line
2.20.1
author maintainer
#200 lore raw

PATCH 187/203 mmc: mtk-sd: Re-store SDIO IRQs mask at system resume

In reply to Sasha Levin

From: Ulf Hansson <[email protected]>

[ Upstream commit 1c81d69d4c98aab56c5a7d5a810f84aefdb37e9b ]

In cases when SDIO IRQs have been enabled, runtime suspend is prevented by the driver. However, this still means msdc_runtime_suspend|resume() gets called during system suspend/resume, via pm_runtime_force_suspend|resume().

This means during system suspend/resume, the register context of the mtk-sd device most likely loses its register context, even in cases when SDIO IRQs have been enabled.

To re-enable the SDIO IRQs during system resume, the mtk-sd driver currently relies on the mmc core to re-enable the SDIO IRQs when it resumes the SDIO card, but this isn't the recommended solution. Instead, it's better to deal with this locally in the mtk-sd driver, so let's do that.

---
 drivers/mmc/host/mtk-sd.c | 3 +++
 1 file changed, 3 insertions(+)
drivers/mmc/host/mtk-sd.c +3 -0
index 33f4b6387ef71..978c8ccce7e31 100644
@@ -2421,6 +2421,9 @@ static void msdc_restore_reg(struct msdc_host *host)
 	} else {
 		writel(host->save_para.pad_tune, host->base + tune_reg);
 	}
+
+	if (sdio_irq_claimed(host->mmc))
+		__msdc_enable_sdio_irq(host, 1);
 }
 
 static int msdc_runtime_suspend(struct device *dev)
Signature · 1 line
2.20.1
author maintainer
#206 lore raw

PATCH 193/203 drm/amd/powerplay/smu7: enforce minimal VBITimeout (v2)

In reply to Sasha Levin

From: Ahzo <[email protected]>

[ Upstream commit f659bb6dae58c113805f92822e4c16ddd3156b79 ]

This fixes screen corruption/flickering on 75 Hz displays.

v2: make print statement debug only (Alex)

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=102646

---
 drivers/gpu/drm/amd/powerplay/hwmgr/smu7_hwmgr.c | 5 +++++
 1 file changed, 5 insertions(+)
drivers/gpu/drm/amd/powerplay/hwmgr/smu7_hwmgr.c +5 -0
index 487aeee1cf8a5..3c1084de5d59f 100644
@@ -4068,6 +4068,11 @@ static int smu7_program_display_gap(struct pp_hwmgr *hwmgr)
 
 	data->frame_time_x2 = frame_time_in_us * 2 / 100;
 
+	if (data->frame_time_x2 < 280) {
+		pr_debug("%s: enforce minimal VBITimeout: %d -> 280\n", __func__, data->frame_time_x2);
+		data->frame_time_x2 = 280;
+	}
+
 	display_gap2 = pre_vbi_time_in_us * (ref_clock / 100);
 
 	cgs_write_ind_register(hwmgr->device, CGS_IND_REG__SMC, ixCG_DISPLAY_GAP_CNTL2, display_gap2);
Signature · 6 lines
2.20.1

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
author maintainer
#208 lore raw

PATCH 195/203 drm: fix module name in edid_firmware log message

In reply to Sasha Levin

From: Jani Nikula <[email protected]>

[ Upstream commit ade925995b172f1d7410d1c665b2f47c5e99bef0 ]

The module is drm_kms_helper, not drm_kms_firmware.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=204549

Fixes ac6c35a4d8c7 ("drm: add backwards compatibility support for drm_kms_helper.edid_firmware")
---
 drivers/gpu/drm/drm_kms_helper_common.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/gpu/drm/drm_kms_helper_common.c +1 -1
index d9a5ac81949e2..221a8528c9937 100644
@@ -40,7 +40,7 @@ MODULE_LICENSE("GPL and additional rights");
 /* Backward compatibility for drm_kms_helper.edid_firmware */
 static int edid_firmware_set(const char *val, const struct kernel_param *kp)
 {
-	DRM_NOTE("drm_kms_firmware.edid_firmware is deprecated, please use drm.edid_firmware instead.\n");
+	DRM_NOTE("drm_kms_helper.edid_firmware is deprecated, please use drm.edid_firmware instead.\n");
 
 	return __drm_set_edid_firmware_path(val);
 }
Signature · 1 line
2.20.1

Sasha Levin

author maintainer
#0 lore raw

PATCH 1/203 ALSA: hda: Flush interrupts on disabling

From: Chris Wilson <[email protected]>

[ Upstream commit caa8422d01e983782548648e125fd617cadcec3f ]

I was looking at

<4> [241.835158] general protection fault: 0000 [#1] PREEMPT SMP PTI
<4> [241.835181] CPU: 1 PID: 214 Comm: kworker/1:3 Tainted: G U 5.2.0-CI-CI_DRM_6509+ #1
<4> [241.835199] Hardware name: Dell Inc. OptiPlex 745 /0GW726, BIOS 2.3.1 05/21/2007
<4> [241.835234] Workqueue: events snd_hdac_bus_process_unsol_events [snd_hda_core]
<4> [241.835256] RIP: 0010:input_handle_event+0x16d/0x5e0
<4> [241.835270] Code: 48 8b 93 58 01 00 00 8b 52 08 89 50 04 8b 83 f8 06 00 00 48 8b 93 00 07 00 00 8d 70 01 48 8d 04 c2 83 e1 08 89 b3 f8 06 00 00 <66> 89 28 66 44 89 60 02 44 89 68 04 8b 93 f8 06 00 00 0f 84 fd fe <4> [241.835304] RSP: 0018:ffffc9000019fda0 EFLAGS: 00010046
<4> [241.835317] RAX: 6b6b6b6ec6c6c6c3 RBX: ffff8880290fefc8 RCX: 0000000000000000
<4> [241.835332] RDX: 000000006b6b6b6b RSI: 000000006b6b6b6c RDI: 0000000000000046
<4> [241.835347] RBP: 0000000000000005 R08: 0000000000000000 R09: 0000000000000001
<4> [241.835362] R10: ffffc9000019faa0 R11: 0000000000000000 R12: 0000000000000004
<4> [241.835377] R13: 0000000000000000 R14: ffff8880290ff1d0 R15: 0000000000000293
<4> [241.835392] FS: 0000000000000000(0000) GS:ffff88803de80000(0000) knlGS:0000000000000000
<4> [241.835409] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
<4> [241.835422] CR2: 00007ffe9a99e9b7 CR3: 000000002f588000 CR4: 00000000000006e0
<4> [241.835436] Call Trace:

<4> [241.835449]  input_event+0x45/0x70
<4> [241.835464]  snd_jack_report+0xdc/0x100
<4> [241.835490]  snd_hda_jack_report_sync+0x83/0xc0 [snd_hda_codec]
<4> [241.835512]  snd_hdac_bus_process_unsol_events+0x5a/0x70 [snd_hda_core]
<4> [241.835530]  process_one_work+0x245/0x610

which has the hallmarks of a worker queued from interrupt after it was supposedly cancelled (note the POISON_FREE), and I could not see where the interrupt would be flushed on shutdown so added the likely suspects.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111174

---
 sound/hda/hdac_controller.c | 2 ++
 sound/pci/hda/hda_intel.c   | 2 +-
 2 files changed, 3 insertions(+), 1 deletion(-)
sound/hda/hdac_controller.c +2 -0
index 3b0110545070a..196bbc85699e5 100644
@@ -447,6 +447,8 @@ static void azx_int_disable(struct hdac_bus *bus)
 	list_for_each_entry(azx_dev, &bus->stream_list, list)
 		snd_hdac_stream_updateb(azx_dev, SD_CTL, SD_INT_MASK, 0);
 
+	synchronize_irq(bus->irq);
+
 	/* disable SIE for all streams */
 	snd_hdac_chip_writeb(bus, INTCTL, 0);
 
sound/pci/hda/hda_intel.c +1 -1
index 99fc0917339bb..0ed2be83706d6 100644
@@ -1349,9 +1349,9 @@ static int azx_free(struct azx *chip)
 	}
 
 	if (bus->chip_init) {
+		azx_stop_chip(chip);
 		azx_clear_irq_pending(chip);
 		azx_stop_all_streams(chip);
-		azx_stop_chip(chip);
 	}
 
 	if (bus->irq >= 0)
Signature · 1 line
2.20.1
author maintainer
#1 lore raw

PATCH 2/203 ASoC: SOF: Intel: hda: Make hdac_device device-managed

From: Ranjani Sridharan <[email protected]>

[ Upstream commit ef9bec27485fefb6b93168fea73fda0dc9638046 ]

snd_hdac_ext_bus_device_exit() has been recently modified to no longer free the hdac device. SOF allocates memory for hdac_device and hda_hda_priv with kzalloc. Make them device-managed instead so that they will be freed when the SOF driver is unloaded.

Because of the above change, hda_codec is device-managed and it will be freed when the ASoC device is removed. Freeing the codec in snd_hda_codec_dev_release() leads to kernel panic while unloading and reloading the ASoC driver. So, avoid freeing the hda_codec for ASoC driver. This is done in the same patch to avoid bisect failure.

---
 sound/pci/hda/hda_codec.c       | 8 +++++++-
 sound/soc/sof/intel/hda-codec.c | 6 ++----
 2 files changed, 9 insertions(+), 5 deletions(-)
sound/pci/hda/hda_codec.c +7 -1
index 51f10ed9bc432..a2fb19129219e 100644
@@ -846,7 +846,13 @@ static void snd_hda_codec_dev_release(struct device *dev)
 	snd_hda_sysfs_clear(codec);
 	kfree(codec->modelname);
 	kfree(codec->wcaps);
-	kfree(codec);
+
+	/*
+	 * In the case of ASoC HD-audio, hda_codec is device managed.
+	 * It will be freed when the ASoC device is removed.
+	 */
+	if (codec->core.type == HDA_DEV_LEGACY)
+		kfree(codec);
 }
 
 #define DEV_NAME_LEN 31
sound/soc/sof/intel/hda-codec.c +2 -4
index b8b37f0823094..0d8437b080bfa 100644
@@ -62,8 +62,7 @@ static int hda_codec_probe(struct snd_sof_dev *sdev, int address)
 		address, resp);
 
 #if IS_ENABLED(CONFIG_SND_SOC_SOF_HDA_AUDIO_CODEC)
-	/* snd_hdac_ext_bus_device_exit will use kfree to free hdev */
-	hda_priv = kzalloc(sizeof(*hda_priv), GFP_KERNEL);
+	hda_priv = devm_kzalloc(sdev->dev, sizeof(*hda_priv), GFP_KERNEL);
 	if (!hda_priv)
 		return -ENOMEM;
 
@@ -82,8 +81,7 @@ static int hda_codec_probe(struct snd_sof_dev *sdev, int address)
 
 	return 0;
 #else
-	/* snd_hdac_ext_bus_device_exit will use kfree to free hdev */
-	hdev = kzalloc(sizeof(*hdev), GFP_KERNEL);
+	hdev = devm_kzalloc(sdev->dev, sizeof(*hdev), GFP_KERNEL);
 	if (!hdev)
 		return -ENOMEM;
 
Signature · 1 line
2.20.1
author maintainer
#3 lore raw

PATCH 4/203 ALSA: hda/hdmi - Don't report spurious jack state changes

In reply to Sasha Levin

From: Takashi Iwai <[email protected]>

[ Upstream commit 551626ec0ad28dc43cae3094c35be7088cc625ab ]

The HDMI jack handling reports the state change always via snd_jack_report() whenever hdmi_present_sense() is called, even if the state itself doesn't change from the previous time. This is mostly harmless but still a bit confusing to user-space.

This patch reduces such spurious jack state changes and reports only when the state really changed. Also, as a minor optimization, avoid overwriting the pin ELD data when the state is identical.

---
 sound/pci/hda/patch_hdmi.c | 32 ++++++++++++++++++--------------
 1 file changed, 18 insertions(+), 14 deletions(-)
sound/pci/hda/patch_hdmi.c +18 -14
index bea7b09610809..c380596b2e84c 100644
@@ -1421,7 +1421,7 @@ static void hdmi_pcm_reset_pin(struct hdmi_spec *spec,
 /* update per_pin ELD from the given new ELD;
  * setup info frame and notification accordingly
  */
-static void update_eld(struct hda_codec *codec,
+static bool update_eld(struct hda_codec *codec,
 		       struct hdmi_spec_per_pin *per_pin,
 		       struct hdmi_eld *eld)
 {
@@ -1452,18 +1452,22 @@ static void update_eld(struct hda_codec *codec,
 		snd_hdmi_show_eld(codec, &eld->info);
 
 	eld_changed = (pin_eld->eld_valid != eld->eld_valid);
-	if (eld->eld_valid && pin_eld->eld_valid)
+	eld_changed |= (pin_eld->monitor_present != eld->monitor_present);
+	if (!eld_changed && eld->eld_valid && pin_eld->eld_valid)
 		if (pin_eld->eld_size != eld->eld_size ||
 		    memcmp(pin_eld->eld_buffer, eld->eld_buffer,
 			   eld->eld_size) != 0)
 			eld_changed = true;
 
-	pin_eld->monitor_present = eld->monitor_present;
-	pin_eld->eld_valid = eld->eld_valid;
-	pin_eld->eld_size = eld->eld_size;
-	if (eld->eld_valid)
-		memcpy(pin_eld->eld_buffer, eld->eld_buffer, eld->eld_size);
-	pin_eld->info = eld->info;
+	if (eld_changed) {
+		pin_eld->monitor_present = eld->monitor_present;
+		pin_eld->eld_valid = eld->eld_valid;
+		pin_eld->eld_size = eld->eld_size;
+		if (eld->eld_valid)
+			memcpy(pin_eld->eld_buffer, eld->eld_buffer,
+			       eld->eld_size);
+		pin_eld->info = eld->info;
+	}
 
 	/*
 	 * Re-setup pin and infoframe. This is needed e.g. when
@@ -1481,6 +1485,7 @@ static void update_eld(struct hda_codec *codec,
 			       SNDRV_CTL_EVENT_MASK_VALUE |
 			       SNDRV_CTL_EVENT_MASK_INFO,
 			       &get_hdmi_pcm(spec, pcm_idx)->eld_ctl->id);
+	return eld_changed;
 }
 
 /* update ELD and jack state via HD-audio verbs */
@@ -1582,6 +1587,7 @@ static void sync_eld_via_acomp(struct hda_codec *codec,
 	struct hdmi_spec *spec = codec->spec;
 	struct hdmi_eld *eld = &spec->temp_eld;
 	struct snd_jack *jack = NULL;
+	bool changed;
 	int size;
 
 	mutex_lock(&per_pin->lock);
@@ -1608,15 +1614,13 @@ static void sync_eld_via_acomp(struct hda_codec *codec,
 	 * disconnected event. Jack must be fetched before update_eld()
 	 */
 	jack = pin_idx_to_jack(codec, per_pin);
-	update_eld(codec, per_pin, eld);
+	changed = update_eld(codec, per_pin, eld);
 	if (jack == NULL)
 		jack = pin_idx_to_jack(codec, per_pin);
-	if (jack == NULL)
-		goto unlock;
-	snd_jack_report(jack,
-			(eld->monitor_present && eld->eld_valid) ?
+	if (changed && jack)
+		snd_jack_report(jack,
+				(eld->monitor_present && eld->eld_valid) ?
 				SND_JACK_AVOUT : 0);
- unlock:
 	mutex_unlock(&per_pin->lock);
 }
 
Signature · 1 line
2.20.1
author maintainer
#2 lore raw

PATCH 3/203 cpufreq: ap806: Add NULL check after kcalloc

In reply to Sasha Levin

From: Hariprasad Kelam <[email protected]>

[ Upstream commit 3355c91b79394593ebbb197c8e930a91826f4ff3 ]

Add NULL check after kcalloc.

Fix below issue reported by coccicheck ./drivers/cpufreq/armada-8k-cpufreq.c:138:1-12: alloc with no test, possible model on line 151

---
 drivers/cpufreq/armada-8k-cpufreq.c | 2 ++
 1 file changed, 2 insertions(+)
drivers/cpufreq/armada-8k-cpufreq.c +2 -0
index 988ebc326bdbb..39e34f5066d3d 100644
@@ -136,6 +136,8 @@ static int __init armada_8k_cpufreq_init(void)
 
 	nb_cpus = num_possible_cpus();
 	freq_tables = kcalloc(nb_cpus, sizeof(*freq_tables), GFP_KERNEL);
+	if (!freq_tables)
+		return -ENOMEM;
 	cpumask_copy(&cpus, cpu_possible_mask);
 
 	/*
Signature · 1 line
2.20.1
author maintainer
#7 lore raw

PATCH 8/203 ASoC: tlv320aic31xx: suppress error message for EPROBE_DEFER

In reply to Sasha Levin

From: Lucas Stach <[email protected]>

[ Upstream commit b7e814deae33eb30f8f8c6528e8e69b107978d88 ]

Both the supplies and reset GPIO might need a probe deferral for the resource to be available. Don't print a error message in that case, as it is a normal operating condition.

---
 sound/soc/codecs/tlv320aic31xx.c | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)
sound/soc/codecs/tlv320aic31xx.c +5 -2
index 9b37e98da0db1..26a4f6cd32883 100644
@@ -1553,7 +1553,8 @@ static int aic31xx_i2c_probe(struct i2c_client *i2c,
 	aic31xx->gpio_reset = devm_gpiod_get_optional(aic31xx->dev, "reset",
 						      GPIOD_OUT_LOW);
 	if (IS_ERR(aic31xx->gpio_reset)) {
-		dev_err(aic31xx->dev, "not able to acquire gpio\n");
+		if (PTR_ERR(aic31xx->gpio_reset) != -EPROBE_DEFER)
+			dev_err(aic31xx->dev, "not able to acquire gpio\n");
 		return PTR_ERR(aic31xx->gpio_reset);
 	}
 
@@ -1564,7 +1565,9 @@ static int aic31xx_i2c_probe(struct i2c_client *i2c,
 				      ARRAY_SIZE(aic31xx->supplies),
 				      aic31xx->supplies);
 	if (ret) {
-		dev_err(aic31xx->dev, "Failed to request supplies: %d\n", ret);
+		if (ret != -EPROBE_DEFER)
+			dev_err(aic31xx->dev,
+				"Failed to request supplies: %d\n", ret);
 		return ret;
 	}
 
Signature · 1 line
2.20.1
author maintainer
#9 lore raw

PATCH 10/203 ASoC: sgtl5000: Fix charge pump source assignment

In reply to Sasha Levin

From: Oleksandr Suvorov <[email protected]>

[ Upstream commit b6319b061ba279577fd7030a9848fbd6a17151e3 ]

If VDDA != VDDIO and any of them is greater than 3.1V, charge pump source can be assigned automatically [1].

[1] https://www.nxp.com/docs/en/data-sheet/SGTL5000.pdf

---
 sound/soc/codecs/sgtl5000.c | 15 ++++++++++-----
 1 file changed, 10 insertions(+), 5 deletions(-)
sound/soc/codecs/sgtl5000.c +10 -5
index aad9eca41587e..7cbaedffa1ef7 100644
@@ -1173,12 +1173,17 @@ static int sgtl5000_set_power_regs(struct snd_soc_component *component)
 					SGTL5000_INT_OSC_EN);
 		/* Enable VDDC charge pump */
 		ana_pwr |= SGTL5000_VDDC_CHRGPMP_POWERUP;
-	} else if (vddio >= 3100 && vdda >= 3100) {
+	} else {
 		ana_pwr &= ~SGTL5000_VDDC_CHRGPMP_POWERUP;
-		/* VDDC use VDDIO rail */
-		lreg_ctrl |= SGTL5000_VDDC_ASSN_OVRD;
-		lreg_ctrl |= SGTL5000_VDDC_MAN_ASSN_VDDIO <<
-			    SGTL5000_VDDC_MAN_ASSN_SHIFT;
+		/*
+		 * if vddio == vdda the source of charge pump should be
+		 * assigned manually to VDDIO
+		 */
+		if (vddio == vdda) {
+			lreg_ctrl |= SGTL5000_VDDC_ASSN_OVRD;
+			lreg_ctrl |= SGTL5000_VDDC_MAN_ASSN_VDDIO <<
+				    SGTL5000_VDDC_MAN_ASSN_SHIFT;
+		}
 	}
 
 	snd_soc_component_write(component, SGTL5000_CHIP_LINREG_CTRL, lreg_ctrl);
Signature · 1 line
2.20.1
author maintainer
#8 lore raw

PATCH 9/203 ASoC: sgtl5000: Fix of unmute outputs on probe

In reply to Sasha Levin

From: Oleksandr Suvorov <[email protected]>

[ Upstream commit 631bc8f0134ae9620d86a96b8c5f9445d91a2dca ]

To enable "zero cross detect" for ADC/HP, change HP_ZCD_EN/ADC_ZCD_EN bits only instead of writing the whole CHIP_ANA_CTRL register.

---
 sound/soc/codecs/sgtl5000.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
sound/soc/codecs/sgtl5000.c +3 -3
index a6a4748c97f9d..aad9eca41587e 100644
@@ -1288,6 +1288,7 @@ static int sgtl5000_probe(struct snd_soc_component *component)
 	int ret;
 	u16 reg;
 	struct sgtl5000_priv *sgtl5000 = snd_soc_component_get_drvdata(component);
+	unsigned int zcd_mask = SGTL5000_HP_ZCD_EN | SGTL5000_ADC_ZCD_EN;
 
 	/* power up sgtl5000 */
 	ret = sgtl5000_set_power_regs(component);
@@ -1315,9 +1316,8 @@ static int sgtl5000_probe(struct snd_soc_component *component)
 	       0x1f);
 	snd_soc_component_write(component, SGTL5000_CHIP_PAD_STRENGTH, reg);
 
-	snd_soc_component_write(component, SGTL5000_CHIP_ANA_CTRL,
-			SGTL5000_HP_ZCD_EN |
-			SGTL5000_ADC_ZCD_EN);
+	snd_soc_component_update_bits(component, SGTL5000_CHIP_ANA_CTRL,
+		zcd_mask, zcd_mask);
 
 	snd_soc_component_update_bits(component, SGTL5000_CHIP_MIC_CTRL,
 			SGTL5000_BIAS_R_MASK,
Signature · 1 line
2.20.1
author maintainer
#12 lore raw

PATCH 13/203 leds: leds-lp5562 allow firmware files up to the maximum length

In reply to Sasha Levin

From: Nick Stoughton <[email protected]>

[ Upstream commit ed2abfebb041473092b41527903f93390d38afa7 ]

Firmware files are in ASCII, using 2 hex characters per byte. The maximum length of a firmware string is therefore

16 (commands) * 2 (bytes per command) * 2 (characters per byte) = 64

Fixes ff45262a85db ("leds: add new LP5562 LED driver")
---
 drivers/leds/leds-lp5562.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)
drivers/leds/leds-lp5562.c +5 -1
index 37632fc637414..edb57c42e8b1d 100644
@@ -260,7 +260,11 @@ static void lp5562_firmware_loaded(struct lp55xx_chip *chip)
 {
 	const struct firmware *fw = chip->fw;
 
-	if (fw->size > LP5562_PROGRAM_LENGTH) {
+	/*
+	 * the firmware is encoded in ascii hex character, with 2 chars
+	 * per byte
+	 */
+	if (fw->size > (LP5562_PROGRAM_LENGTH * 2)) {
 		dev_err(&chip->cl->dev, "firmware data size overflow: %zu\n",
 			fw->size);
 		return;
Signature · 1 line
2.20.1
author maintainer
#14 lore raw

PATCH 15/203 media: dib0700: fix link error for dibx000_i2c_set_speed

In reply to Sasha Levin

From: Arnd Bergmann <[email protected]>

[ Upstream commit 765bb8610d305ee488b35d07e2a04ae52fb2df9c ]

When CONFIG_DVB_DIB9000 is disabled, we can still compile code that now fails to link against dibx000_i2c_set_speed:

drivers/media/usb/dvb-usb/dib0700_devices.o: In function `dib01x0_pmu_update.constprop.7':
dib0700_devices.c:(.text.unlikely+0x1c9c): undefined reference to `dibx000_i2c_set_speed'

The call sites are both through dib01x0_pmu_update(), which gets passed an 'i2c' pointer from dib9000_get_i2c_master(), which has returned NULL. Checking this pointer seems to be a good idea anyway, and it avoids the link failure in most cases.

Sean Young found another case that is not fixed by that, where certain gcc versions leave an unused function in place that causes the link error, but adding an explict IS_ENABLED() check also solves this.

Fixes b7f54910ce01 ("V4L/DVB (4647): Added module for DiB0700 based devices")
---
 drivers/media/usb/dvb-usb/dib0700_devices.c | 8 ++++++++
 1 file changed, 8 insertions(+)
drivers/media/usb/dvb-usb/dib0700_devices.c +8 -0
index 66d685065e065..ab7a100ec84fe 100644
@@ -2439,9 +2439,13 @@ static int dib9090_tuner_attach(struct dvb_usb_adapter *adap)
 		8, 0x0486,
 	};
 
+	if (!IS_ENABLED(CONFIG_DVB_DIB9000))
+		return -ENODEV;
 	if (dvb_attach(dib0090_fw_register, adap->fe_adap[0].fe, i2c, &dib9090_dib0090_config) == NULL)
 		return -ENODEV;
 	i2c = dib9000_get_i2c_master(adap->fe_adap[0].fe, DIBX000_I2C_INTERFACE_GPIO_1_2, 0);
+	if (!i2c)
+		return -ENODEV;
 	if (dib01x0_pmu_update(i2c, data_dib190, 10) != 0)
 		return -ENODEV;
 	dib0700_set_i2c_speed(adap->dev, 1500);
@@ -2517,10 +2521,14 @@ static int nim9090md_tuner_attach(struct dvb_usb_adapter *adap)
 		0, 0x00ef,
 		8, 0x0406,
 	};
+	if (!IS_ENABLED(CONFIG_DVB_DIB9000))
+		return -ENODEV;
 	i2c = dib9000_get_tuner_interface(adap->fe_adap[0].fe);
 	if (dvb_attach(dib0090_fw_register, adap->fe_adap[0].fe, i2c, &nim9090md_dib0090_config[0]) == NULL)
 		return -ENODEV;
 	i2c = dib9000_get_i2c_master(adap->fe_adap[0].fe, DIBX000_I2C_INTERFACE_GPIO_1_2, 0);
+	if (!i2c)
+		return -ENODEV;
 	if (dib01x0_pmu_update(i2c, data_dib190, 10) < 0)
 		return -ENODEV;
 
Signature · 1 line
2.20.1
author maintainer
#17 lore raw

PATCH 18/203 media: exynos4-is: fix leaked of_node references

In reply to Sasha Levin

From: Wen Yang <[email protected]>

[ Upstream commit da79bf41a4d170ca93cc8f3881a70d734a071c37 ]

The call to of_get_child_by_name returns a node pointer with refcount incremented thus it must be explicitly decremented after the last usage.

Detected by coccinelle with the following warnings:
drivers/media/platform/exynos4-is/fimc-is.c:813:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 807, but without a corresponding object release within this function. drivers/media/platform/exynos4-is/fimc-is.c:870:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 807, but without a corresponding object release within this function. drivers/media/platform/exynos4-is/fimc-is.c:885:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 807, but without a corresponding object release within this function. drivers/media/platform/exynos4-is/media-dev.c:545:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 541, but without a corresponding object release within this function. drivers/media/platform/exynos4-is/media-dev.c:528:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 499, but without a corresponding object release within this function. drivers/media/platform/exynos4-is/media-dev.c:534:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 499, but without a corresponding object release within this function.

---
 drivers/media/platform/exynos4-is/fimc-is.c   | 1 +
 drivers/media/platform/exynos4-is/media-dev.c | 2 ++
 2 files changed, 3 insertions(+)
drivers/media/platform/exynos4-is/fimc-is.c +1 -0
index e043d55133a31..b7cc8e651e327 100644
@@ -806,6 +806,7 @@ static int fimc_is_probe(struct platform_device *pdev)
 		return -ENODEV;
 
 	is->pmu_regs = of_iomap(node, 0);
+	of_node_put(node);
 	if (!is->pmu_regs)
 		return -ENOMEM;
 
drivers/media/platform/exynos4-is/media-dev.c +2 -0
index d53427a8db11d..a838189d44902 100644
@@ -501,6 +501,7 @@ static int fimc_md_register_sensor_entities(struct fimc_md *fmd)
 			continue;
 
 		ret = fimc_md_parse_port_node(fmd, port, index);
+		of_node_put(port);
 		if (ret < 0) {
 			of_node_put(node);
 			goto cleanup;
@@ -542,6 +543,7 @@ static int __of_get_csis_id(struct device_node *np)
 	if (!np)
 		return -EINVAL;
 	of_property_read_u32(np, "reg", &reg);
+	of_node_put(np);
 	return reg - FIMC_INPUT_MIPI_CSI2_0;
 }
 
Signature · 1 line
2.20.1
author maintainer
#16 lore raw

PATCH 17/203 ASoC: SOF: pci: mark last_busy value at runtime PM init

In reply to Sasha Levin

From: Pan Xiuli <[email protected]>

[ Upstream commit f1b1b9b136827915624136624ff54aba5890a15b ]

If last_busy value is not set at runtime PM enable, the device will be suspend immediately after usage counter is 0. Set the last_busy value to make sure delay is working at first boot up.

---
 sound/soc/sof/sof-pci-dev.c | 3 +++
 1 file changed, 3 insertions(+)
sound/soc/sof/sof-pci-dev.c +3 -0
index 65d1bac4c6b8b..6fd3df7c57a3a 100644
@@ -223,6 +223,9 @@ static void sof_pci_probe_complete(struct device *dev)
 	 */
 	pm_runtime_allow(dev);
 
+	/* mark last_busy for pm_runtime to make sure not suspend immediately */
+	pm_runtime_mark_last_busy(dev);
+
 	/* follow recommendation in pci-driver.c to decrement usage counter */
 	pm_runtime_put_noidle(dev);
 }
Signature · 1 line
2.20.1
author maintainer
#15 lore raw

PATCH 16/203 media: mtk-cir: lower de-glitch counter for rc-mm protocol

In reply to Sasha Levin

From: Sean Young <[email protected]>

[ Upstream commit 5dd4b89dc098bf22cd13e82a308f42a02c102b2b ]

The rc-mm protocol can't be decoded by the mtk-cir since the de-glitch filter removes pulses/spaces shorter than 294 microseconds.

Tested on a BananaPi R2.

---
 drivers/media/rc/mtk-cir.c | 8 ++++++++
 1 file changed, 8 insertions(+)
drivers/media/rc/mtk-cir.c +8 -0
index 50fb0aebb8d40..f2259082e3d82 100644
@@ -35,6 +35,11 @@
 /* Fields containing pulse width data */
 #define MTK_WIDTH_MASK		  (GENMASK(7, 0))
 
+/* IR threshold */
+#define MTK_IRTHD		 0x14
+#define MTK_DG_CNT_MASK		 (GENMASK(12, 8))
+#define MTK_DG_CNT(x)		 ((x) << 8)
+
 /* Bit to enable interrupt */
 #define MTK_IRINT_EN		  BIT(0)
 
@@ -398,6 +403,9 @@ static int mtk_ir_probe(struct platform_device *pdev)
 	mtk_w32_mask(ir, val, ir->data->fields[MTK_HW_PERIOD].mask,
 		     ir->data->fields[MTK_HW_PERIOD].reg);
 
+	/* Set de-glitch counter */
+	mtk_w32_mask(ir, MTK_DG_CNT(1), MTK_DG_CNT_MASK, MTK_IRTHD);
+
 	/* Enable IR and PWM */
 	val = mtk_r32(ir, MTK_CONFIG_HIGH_REG);
 	val |= MTK_OK_COUNT(ir->data->ok_count) |  MTK_PWM_EN | MTK_IR_EN;
Signature · 1 line
2.20.1
author maintainer
#13 lore raw

PATCH 14/203 ASoC: SOF: reset DMA state in prepare

In reply to Sasha Levin

From: Kai Vehmanen <[email protected]>

[ Upstream commit 04c8027764bc82a325d3abc6f39a6a4642a937cb ]

When application goes through SUSPEND/STOP->PREPARE->START cycle, we should always reprogram the SOF device to start DMA from a known state so that hw_ptr/appl_ptrs remain valid. This is expected by ALSA core as it resets the buffer state as part of prepare (see snd_pcm_do_prepare()).

Fix the issue by forcing reconfiguration of the FW with STREAM_PCM_PARAMS in prepare(). Use combined logic to handle prepare and the existing flow to reprogram hw-params after system suspend.

Without the fix, first call to pcm pointer() will return an invalid hw_ptr and application may immediately observe XRUN status, unless "start_threshold" SW parameter is set to maximum value by the application.

---
 sound/soc/sof/pcm.c      | 27 +++++++++++++++------------
 sound/soc/sof/pm.c       |  2 +-
 sound/soc/sof/sof-priv.h |  2 +-
 3 files changed, 17 insertions(+), 14 deletions(-)
sound/soc/sof/pcm.c +15 -12
index 334e9d59b1baf..3b8955e755b24 100644
@@ -208,12 +208,11 @@ static int sof_pcm_hw_params(struct snd_pcm_substream *substream,
 	if (ret < 0)
 		return ret;
 
+	spcm->prepared[substream->stream] = true;
+
 	/* save pcm hw_params */
 	memcpy(&spcm->params[substream->stream], params, sizeof(*params));
 
-	/* clear hw_params_upon_resume flag */
-	spcm->hw_params_upon_resume[substream->stream] = 0;
-
 	return ret;
 }
 
@@ -236,6 +235,9 @@ static int sof_pcm_hw_free(struct snd_pcm_substream *substream)
 	if (!spcm)
 		return -EINVAL;
 
+	if (!spcm->prepared[substream->stream])
+		return 0;
+
 	dev_dbg(sdev->dev, "pcm: free stream %d dir %d\n", spcm->pcm.pcm_id,
 		substream->stream);
 
@@ -258,6 +260,8 @@ static int sof_pcm_hw_free(struct snd_pcm_substream *substream)
 	if (ret < 0)
 		dev_err(sdev->dev, "error: platform hw free failed\n");
 
+	spcm->prepared[substream->stream] = false;
+
 	return ret;
 }
 
@@ -278,11 +282,7 @@ static int sof_pcm_prepare(struct snd_pcm_substream *substream)
 	if (!spcm)
 		return -EINVAL;
 
-	/*
-	 * check if hw_params needs to be set-up again.
-	 * This is only needed when resuming from system sleep.
-	 */
-	if (!spcm->hw_params_upon_resume[substream->stream])
+	if (spcm->prepared[substream->stream])
 		return 0;
 
 	dev_dbg(sdev->dev, "pcm: prepare stream %d dir %d\n", spcm->pcm.pcm_id,
@@ -311,6 +311,7 @@ static int sof_pcm_trigger(struct snd_pcm_substream *substream, int cmd)
 	struct snd_sof_pcm *spcm;
 	struct sof_ipc_stream stream;
 	struct sof_ipc_reply reply;
+	bool reset_hw_params = false;
 	int ret;
 
 	/* nothing to do for BE */
@@ -351,6 +352,7 @@ static int sof_pcm_trigger(struct snd_pcm_substream *substream, int cmd)
 	case SNDRV_PCM_TRIGGER_SUSPEND:
 	case SNDRV_PCM_TRIGGER_STOP:
 		stream.hdr.cmd |= SOF_IPC_STREAM_TRIG_STOP;
+		reset_hw_params = true;
 		break;
 	default:
 		dev_err(sdev->dev, "error: unhandled trigger cmd %d\n", cmd);
@@ -363,17 +365,17 @@ static int sof_pcm_trigger(struct snd_pcm_substream *substream, int cmd)
 	ret = sof_ipc_tx_message(sdev->ipc, stream.hdr.cmd, &stream,
 				 sizeof(stream), &reply, sizeof(reply));
 
-	if (ret < 0 || cmd != SNDRV_PCM_TRIGGER_SUSPEND)
+	if (ret < 0 || !reset_hw_params)
 		return ret;
 
 	/*
-	 * The hw_free op is usually called when the pcm stream is closed.
-	 * Since the stream is not closed during suspend, the DSP needs to be
-	 * notified explicitly to free pcm to prevent errors upon resume.
+	 * In case of stream is stopped, DSP must be reprogrammed upon
+	 * restart, so free PCM here.
 	 */
 	stream.hdr.size = sizeof(stream);
 	stream.hdr.cmd = SOF_IPC_GLB_STREAM_MSG | SOF_IPC_STREAM_PCM_FREE;
 	stream.comp_id = spcm->stream[substream->stream].comp_id;
+	spcm->prepared[substream->stream] = false;
 
 	/* send IPC to the DSP */
 	return sof_ipc_tx_message(sdev->ipc, stream.hdr.cmd, &stream,
@@ -481,6 +483,7 @@ static int sof_pcm_open(struct snd_pcm_substream *substream)
 	spcm->stream[substream->stream].posn.host_posn = 0;
 	spcm->stream[substream->stream].posn.dai_posn = 0;
 	spcm->stream[substream->stream].substream = substream;
+	spcm->prepared[substream->stream] = false;
 
 	ret = snd_sof_pcm_platform_open(sdev, substream);
 	if (ret < 0)
sound/soc/sof/pm.c +1 -1
index 278abfd10490d..48c6d78d72e2e 100644
@@ -233,7 +233,7 @@ static int sof_set_hw_params_upon_resume(struct snd_sof_dev *sdev)
 
 			state = substream->runtime->status->state;
 			if (state == SNDRV_PCM_STATE_SUSPENDED)
-				spcm->hw_params_upon_resume[dir] = 1;
+				spcm->prepared[dir] = false;
 		}
 	}
 
sound/soc/sof/sof-priv.h +1 -1
index b8c0b2a226845..fa5cb7d2a6602 100644
@@ -297,7 +297,7 @@ struct snd_sof_pcm {
 	struct snd_sof_pcm_stream stream[2];
 	struct list_head list;	/* list in sdev pcm list */
 	struct snd_pcm_hw_params params[2];
-	int hw_params_upon_resume[2]; /* set up hw_params upon resume */
+	bool prepared[2]; /* PCM_PARAMS set successfully */
 };
 
 /* ALSA SOF Kcontrol device */
Signature · 1 line
2.20.1
author maintainer
#11 lore raw

PATCH 12/203 dmaengine: bcm2835: Print error in case setting DMA mask fails

In reply to Sasha Levin

From: Stefan Wahren <[email protected]>

[ Upstream commit 72503b25ee363827aafffc3e8d872e6a92a7e422 ]

During enabling of the RPi 4, we found out that the driver doesn't provide a helpful error message in case setting DMA mask fails. So add one.

---
 drivers/dma/bcm2835-dma.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/dma/bcm2835-dma.c +3 -1
index 8101ff2f05c1c..970f654611bdd 100644
@@ -871,8 +871,10 @@ static int bcm2835_dma_probe(struct platform_device *pdev)
 		pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
 
 	rc = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32));
-	if (rc)
+	if (rc) {
+		dev_err(&pdev->dev, "Unable to set DMA mask\n");
 		return rc;
+	}
 
 	od = devm_kzalloc(&pdev->dev, sizeof(*od), GFP_KERNEL);
 	if (!od)
Signature · 1 line
2.20.1
author maintainer
#10 lore raw

PATCH 11/203 firmware: qcom_scm: Use proper types for dma mappings

In reply to Sasha Levin

From: Stephen Boyd <[email protected]>

[ Upstream commit 6e37ccf78a53296c6c7bf426065762c27829eb84 ]

We need to use the proper types and convert between physical addresses and dma addresses here to avoid mismatch warnings. This is especially important on systems with a different size for dma addresses and physical addresses. Otherwise, we get the following warning:

drivers/firmware/qcom_scm.c: In function "qcom_scm_assign_mem":
drivers/firmware/qcom_scm.c:469:47: error: passing argument 3 of "dma_alloc_coherent" from incompatible pointer type [-Werror=incompatible-pointer-types]

We also fix the size argument to dma_free_coherent() because that size doesn't need to be aligned after it's already aligned on the allocation size. In fact, dma debugging expects the same arguments to be passed to both the allocation and freeing sides of the functions so changing the size is incorrect regardless.

---
 drivers/firmware/qcom_scm.c | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)
drivers/firmware/qcom_scm.c +5 -2
index 2ddc118dba1b4..74b84244a0db8 100644
@@ -9,6 +9,7 @@
 #include <linux/init.h>
 #include <linux/cpumask.h>
 #include <linux/export.h>
+#include <linux/dma-direct.h>
 #include <linux/dma-mapping.h>
 #include <linux/module.h>
 #include <linux/types.h>
@@ -440,6 +441,7 @@ int qcom_scm_assign_mem(phys_addr_t mem_addr, size_t mem_sz,
 	phys_addr_t mem_to_map_phys;
 	phys_addr_t dest_phys;
 	phys_addr_t ptr_phys;
+	dma_addr_t ptr_dma;
 	size_t mem_to_map_sz;
 	size_t dest_sz;
 	size_t src_sz;
@@ -457,9 +459,10 @@ int qcom_scm_assign_mem(phys_addr_t mem_addr, size_t mem_sz,
 	ptr_sz = ALIGN(src_sz, SZ_64) + ALIGN(mem_to_map_sz, SZ_64) +
 			ALIGN(dest_sz, SZ_64);
 
-	ptr = dma_alloc_coherent(__scm->dev, ptr_sz, &ptr_phys, GFP_KERNEL);
+	ptr = dma_alloc_coherent(__scm->dev, ptr_sz, &ptr_dma, GFP_KERNEL);
 	if (!ptr)
 		return -ENOMEM;
+	ptr_phys = dma_to_phys(__scm->dev, ptr_dma);
 
 	/* Fill source vmid detail */
 	src = ptr;
@@ -489,7 +492,7 @@ int qcom_scm_assign_mem(phys_addr_t mem_addr, size_t mem_sz,
 
 	ret = __qcom_scm_assign_mem(__scm->dev, mem_to_map_phys, mem_to_map_sz,
 				    ptr_phys, src_sz, dest_phys, dest_sz);
-	dma_free_coherent(__scm->dev, ALIGN(ptr_sz, SZ_64), ptr, ptr_phys);
+	dma_free_coherent(__scm->dev, ptr_sz, ptr, ptr_dma);
 	if (ret) {
 		dev_err(__scm->dev,
 			"Assign memory protection call failed %d.\n", ret);
Signature · 1 line
2.20.1
author maintainer
#20 lore raw

PATCH 21/203 media: vivid: work around high stack usage with clang

In reply to Sasha Levin

From: Arnd Bergmann <[email protected]>

[ Upstream commit 1a03f91c2c2419c3709c4554952c66695575e91c ]

Building a KASAN-enabled kernel with clang ends up in a case where too much is inlined into vivid_thread_vid_cap() and the stack usage grows a lot, possibly when the register allocation fails to produce efficient code and spills a lot of temporaries to the stack. This uses more than twice the amount of stack than the sum of the individual functions when they are not inlined:

drivers/media/platform/vivid/vivid-kthread-cap.c:766:12: error: stack frame size of 2208 bytes in function 'vivid_thread_vid_cap' [-Werror,-Wframe-larger-than=]

Marking two of the key functions in here as 'noinline_for_stack' avoids the pathological case in clang without any apparent downside for gcc.

---
 drivers/media/platform/vivid/vivid-kthread-cap.c | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)
drivers/media/platform/vivid/vivid-kthread-cap.c +4 -3
index ed466d737a90d..003319d7816d7 100644
@@ -232,8 +232,8 @@ static void *plane_vaddr(struct tpg_data *tpg, struct vivid_buffer *buf,
 	return vbuf;
 }
 
-static int vivid_copy_buffer(struct vivid_dev *dev, unsigned p, u8 *vcapbuf,
-		struct vivid_buffer *vid_cap_buf)
+static noinline_for_stack int vivid_copy_buffer(struct vivid_dev *dev, unsigned p,
+		u8 *vcapbuf, struct vivid_buffer *vid_cap_buf)
 {
 	bool blank = dev->must_blank[vid_cap_buf->vb.vb2_buf.index];
 	struct tpg_data *tpg = &dev->tpg;
@@ -672,7 +672,8 @@ static void vivid_cap_update_frame_period(struct vivid_dev *dev)
 	dev->cap_frame_period = f_period;
 }
 
-static void vivid_thread_vid_cap_tick(struct vivid_dev *dev, int dropped_bufs)
+static noinline_for_stack void vivid_thread_vid_cap_tick(struct vivid_dev *dev,
+							 int dropped_bufs)
 {
 	struct vivid_buffer *vid_cap_buf = NULL;
 	struct vivid_buffer *vbi_cap_buf = NULL;
Signature · 1 line
2.20.1
author maintainer
#22 lore raw

PATCH 23/203 media: i2c: ov5640: Check for devm_gpiod_get_optional() error

In reply to Sasha Levin

From: Fabio Estevam <[email protected]>

[ Upstream commit 8791a102ce579346cea9d2f911afef1c1985213c ]

The power down and reset GPIO are optional, but the return value from devm_gpiod_get_optional() needs to be checked and propagated in the case of error, so that probe deferral can work.

---
 drivers/media/i2c/ov5640.c | 5 +++++
 1 file changed, 5 insertions(+)
drivers/media/i2c/ov5640.c +5 -0
index 759d60c6d6304..afe7920557a8f 100644
@@ -3022,9 +3022,14 @@ static int ov5640_probe(struct i2c_client *client,
 	/* request optional power down pin */
 	sensor->pwdn_gpio = devm_gpiod_get_optional(dev, "powerdown",
 						    GPIOD_OUT_HIGH);
+	if (IS_ERR(sensor->pwdn_gpio))
+		return PTR_ERR(sensor->pwdn_gpio);
+
 	/* request optional reset pin */
 	sensor->reset_gpio = devm_gpiod_get_optional(dev, "reset",
 						     GPIOD_OUT_HIGH);
+	if (IS_ERR(sensor->reset_gpio))
+		return PTR_ERR(sensor->reset_gpio);
 
 	v4l2_i2c_subdev_init(&sensor->sd, client, &ov5640_subdev_ops);
 
Signature · 1 line
2.20.1
author maintainer
#25 lore raw

PATCH 26/203 sched/core: Fix CPU controller for !RT_GROUP_SCHED

In reply to Sasha Levin

From: Juri Lelli <[email protected]>

[ Upstream commit a07db5c0865799ebed1f88be0df50c581fb65029 ]

On !CONFIG_RT_GROUP_SCHED configurations it is currently not possible to move RT tasks between cgroups to which CPU controller has been attached; but it is oddly possible to first move tasks around and then make them RT (setschedule to FIFO/RR).

E.g.:

  # mkdir /sys/fs/cgroup/cpu,cpuacct/group1
  # chrt -fp 10 $$
  # echo $$ > /sys/fs/cgroup/cpu,cpuacct/group1/tasks
  bash: echo: write error: Invalid argument
  # chrt -op 0 $$
  # echo $$ > /sys/fs/cgroup/cpu,cpuacct/group1/tasks
  # chrt -fp 10 $$
  # cat /sys/fs/cgroup/cpu,cpuacct/group1/tasks
  2345
  2598
  # chrt -p 2345
  pid 2345's current scheduling policy: SCHED_FIFO
  pid 2345's current scheduling priority: 10

Also, as Michal noted, it is currently not possible to enable CPU controller on unified hierarchy with !CONFIG_RT_GROUP_SCHED (if there are any kernel RT threads in root cgroup, they can't be migrated to the newly created CPU controller's root in cgroup_update_dfl_csses()).

Existing code comes with a comment saying the "we don't support RT-tasks being in separate groups". Such comment is however stale and belongs to pre-RT_GROUP_SCHED times. Also, it doesn't make much sense for !RT_GROUP_ SCHED configurations, since checks related to RT bandwidth are not performed at all in these cases.

Make moving RT tasks between CPU controller groups viable by removing special case check for RT (and DEADLINE) tasks.

---
 kernel/sched/core.c | 4 ----
 1 file changed, 4 deletions(-)
kernel/sched/core.c +0 -4
index 7fa8e74ad2ab4..d38f007afea74 100644
@@ -6980,10 +6980,6 @@ static int cpu_cgroup_can_attach(struct cgroup_taskset *tset)
 #ifdef CONFIG_RT_GROUP_SCHED
 		if (!sched_rt_can_attach(css_tg(css), task))
 			return -EINVAL;
-#else
-		/* We don't support RT-tasks being in separate groups */
-		if (task->sched_class != &fair_sched_class)
-			return -EINVAL;
 #endif
 		/*
 		 * Serialize against wake_up_new_task() such that if its
Signature · 1 line
2.20.1
author maintainer
#26 lore raw

PATCH 27/203 x86/apic: Make apic_pending_intr_clear() more robust

In reply to Sasha Levin

From: Thomas Gleixner <[email protected]>

[ Upstream commit cc8bf191378c1da8ad2b99cf470ee70193ace84e ]

In course of developing shorthand based IPI support issues with the function which tries to clear eventually pending ISR bits in the local APIC were observed.

1) O-day testing triggered the WARN_ON() in apic_pending_intr_clear().

This warning is emitted when the function fails to clear pending ISR bits or observes pending IRR bits which are not delivered to the CPU after the stale ISR bit(s) are ACK'ed.

Unfortunately the function only emits a WARN_ON() and fails to dump the IRR/ISR content. That's useless for debugging.

Feng added spot on debug printk's which revealed that the stale IRR bit belonged to the APIC timer interrupt vector, but adding ad hoc debug code does not help with sporadic failures in the field.

Rework the loop so the full IRR/ISR contents are saved and on failure dumped.

2) The loop termination logic is interesting at best.

If the machine has no TSC or cpu_khz is not known yet it tries 1 million times to ack stale IRR/ISR bits. What?

With TSC it uses the TSC to calculate the loop termination. It takes a timestamp at entry and terminates the loop when:

(rdtsc() - start_timestamp) >= (cpu_hkz << 10)

That's roughly one second.

Both methods are problematic. The APIC has 256 vectors, which means that in theory max. 256 IRR/ISR bits can be set. In practice this is impossible and the chance that more than a few bits are set is close to zero.

With the pure loop based approach the 1 million retries are complete overkill.

With TSC this can terminate too early in a guest which is running on a heavily loaded host even with only a couple of IRR/ISR bits set. The reason is that after acknowledging the highest priority ISR bit, pending IRRs must get serviced first before the next round of acknowledge can take place as the APIC (real and virtualized) does not honour EOI without a preceeding interrupt on the CPU. And every APIC read/write takes a VMEXIT if the APIC is virtualized. While trying to reproduce the issue 0-day reported it was observed that the guest was scheduled out long enough under heavy load that it terminated after 8 iterations.

Make the loop terminate after 512 iterations. That's plenty enough in any case and does not take endless time to complete.

---
 arch/x86/kernel/apic/apic.c | 107 +++++++++++++++++++++---------------
 1 file changed, 63 insertions(+), 44 deletions(-)
arch/x86/kernel/apic/apic.c +63 -44
index 08fb79f377936..436d462dde715 100644
@@ -1495,54 +1495,72 @@ static void lapic_setup_esr(void)
 			oldvalue, value);
 }
 
-static void apic_pending_intr_clear(void)
+#define APIC_IR_REGS		APIC_ISR_NR
+#define APIC_IR_BITS		(APIC_IR_REGS * 32)
+#define APIC_IR_MAPSIZE		(APIC_IR_BITS / BITS_PER_LONG)
+
+union apic_ir {
+	unsigned long	map[APIC_IR_MAPSIZE];
+	u32		regs[APIC_IR_REGS];
+};
+
+static bool apic_check_and_ack(union apic_ir *irr, union apic_ir *isr)
 {
-	long long max_loops = cpu_khz ? cpu_khz : 1000000;
-	unsigned long long tsc = 0, ntsc;
-	unsigned int queued;
-	unsigned long value;
-	int i, j, acked = 0;
+	int i, bit;
+
+	/* Read the IRRs */
+	for (i = 0; i < APIC_IR_REGS; i++)
+		irr->regs[i] = apic_read(APIC_IRR + i * 0x10);
+
+	/* Read the ISRs */
+	for (i = 0; i < APIC_IR_REGS; i++)
+		isr->regs[i] = apic_read(APIC_ISR + i * 0x10);
 
-	if (boot_cpu_has(X86_FEATURE_TSC))
-		tsc = rdtsc();
 	/*
-	 * After a crash, we no longer service the interrupts and a pending
-	 * interrupt from previous kernel might still have ISR bit set.
-	 *
-	 * Most probably by now CPU has serviced that pending interrupt and
-	 * it might not have done the ack_APIC_irq() because it thought,
-	 * interrupt came from i8259 as ExtInt. LAPIC did not get EOI so it
-	 * does not clear the ISR bit and cpu thinks it has already serivced
-	 * the interrupt. Hence a vector might get locked. It was noticed
-	 * for timer irq (vector 0x31). Issue an extra EOI to clear ISR.
+	 * If the ISR map is not empty. ACK the APIC and run another round
+	 * to verify whether a pending IRR has been unblocked and turned
+	 * into a ISR.
 	 */
-	do {
-		queued = 0;
-		for (i = APIC_ISR_NR - 1; i >= 0; i--)
-			queued |= apic_read(APIC_IRR + i*0x10);
-
-		for (i = APIC_ISR_NR - 1; i >= 0; i--) {
-			value = apic_read(APIC_ISR + i*0x10);
-			for_each_set_bit(j, &value, 32) {
-				ack_APIC_irq();
-				acked++;
-			}
-		}
-		if (acked > 256) {
-			pr_err("LAPIC pending interrupts after %d EOI\n", acked);
-			break;
-		}
-		if (queued) {
-			if (boot_cpu_has(X86_FEATURE_TSC) && cpu_khz) {
-				ntsc = rdtsc();
-				max_loops = (long long)cpu_khz << 10;
-				max_loops -= ntsc - tsc;
-			} else {
-				max_loops--;
-			}
-		}
-	} while (queued && max_loops > 0);
-	WARN_ON(max_loops <= 0);
+	if (!bitmap_empty(isr->map, APIC_IR_BITS)) {
+		/*
+		 * There can be multiple ISR bits set when a high priority
+		 * interrupt preempted a lower priority one. Issue an ACK
+		 * per set bit.
+		 */
+		for_each_set_bit(bit, isr->map, APIC_IR_BITS)
+			ack_APIC_irq();
+		return true;
+	}
+
+	return !bitmap_empty(irr->map, APIC_IR_BITS);
+}
+
+/*
+ * After a crash, we no longer service the interrupts and a pending
+ * interrupt from previous kernel might still have ISR bit set.
+ *
+ * Most probably by now the CPU has serviced that pending interrupt and it
+ * might not have done the ack_APIC_irq() because it thought, interrupt
+ * came from i8259 as ExtInt. LAPIC did not get EOI so it does not clear
+ * the ISR bit and cpu thinks it has already serivced the interrupt. Hence
+ * a vector might get locked. It was noticed for timer irq (vector
+ * 0x31). Issue an extra EOI to clear ISR.
+ *
+ * If there are pending IRR bits they turn into ISR bits after a higher
+ * priority ISR bit has been acked.
+ */
+static void apic_pending_intr_clear(void)
+{
+	union apic_ir irr, isr;
+	unsigned int i;
+
+	/* 512 loops are way oversized and give the APIC a chance to obey. */
+	for (i = 0; i < 512; i++) {
+		if (!apic_check_and_ack(&irr, &isr))
+			return;
+	}
+	/* Dump the IRR/ISR content if that failed */
+	pr_warn("APIC: Stale IRR: %256pb ISR: %256pb\n", irr.map, isr.map);
 }
 
 /**
@@ -1610,6 +1628,7 @@ static void setup_local_APIC(void)
 	value &= ~APIC_TPRI_MASK;
 	apic_write(APIC_TASKPRI, value);
 
+	/* Clear eventually stale ISR/IRR bits */
 	apic_pending_intr_clear();
 
 	/*
Signature · 1 line
2.20.1
author maintainer
#23 lore raw

PATCH 24/203 time/tick-broadcast: Fix tick_broadcast_offline() lockdep complaint

In reply to Sasha Levin

From: "Paul E. McKenney" <[email protected]>

[ Upstream commit 84ec3a0787086fcd25f284f59b3aa01fd6fc0a5d ]

time/tick-broadcast: Fix tick_broadcast_offline() lockdep complaint

The TASKS03 and TREE04 rcutorture scenarios produce the following lockdep complaint:

	WARNING: inconsistent lock state
	5.2.0-rc1+ #513 Not tainted
	--------------------------------
	inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
	migration/1/14 [HC0[0]:SC0[0]:HE1:SE1] takes:
	(____ptrval____) (tick_broadcast_lock){?...}, at: tick_broadcast_offline+0xf/0x70
	{IN-HARDIRQ-W} state was registered at:
	  lock_acquire+0xb0/0x1c0
	  _raw_spin_lock_irqsave+0x3c/0x50
	  tick_broadcast_switch_to_oneshot+0xd/0x40
	  tick_switch_to_oneshot+0x4f/0xd0
	  hrtimer_run_queues+0xf3/0x130
	  run_local_timers+0x1c/0x50
	  update_process_times+0x1c/0x50
	  tick_periodic+0x26/0xc0
	  tick_handle_periodic+0x1a/0x60
	  smp_apic_timer_interrupt+0x80/0x2a0
	  apic_timer_interrupt+0xf/0x20
	  _raw_spin_unlock_irqrestore+0x4e/0x60
	  rcu_nocb_gp_kthread+0x15d/0x590
	  kthread+0xf3/0x130
	  ret_from_fork+0x3a/0x50
	irq event stamp: 171
	hardirqs last  enabled at (171): [<ffffffff8a201a37>] trace_hardirqs_on_thunk+0x1a/0x1c
	hardirqs last disabled at (170): [<ffffffff8a201a53>] trace_hardirqs_off_thunk+0x1a/0x1c
	softirqs last  enabled at (0): [<ffffffff8a264ee0>] copy_process.part.56+0x650/0x1cb0
	softirqs last disabled at (0): [<0000000000000000>] 0x0

        [...]

To reproduce, run the following rcutorture test:

 $ tools/testing/selftests/rcutorture/bin/kvm.sh --duration 5 --kconfig "CONFIG_DEBUG_LOCK_ALLOC=y CONFIG_PROVE_LOCKING=y" --configs "TASKS03 TREE04"

It turns out that tick_broadcast_offline() was an innocent bystander. After all, interrupts are supposed to be disabled throughout take_cpu_down(), and therefore should have been disabled upon entry to tick_offline_cpu() and thus to tick_broadcast_offline(). This suggests that one of the CPU-hotplug notifiers was incorrectly enabling interrupts, and leaving them enabled on return.

Some debugging code showed that the culprit was sched_cpu_dying(). It had irqs enabled after return from sched_tick_stop(). Which in turn had irqs enabled after return from cancel_delayed_work_sync(). Which is a wrapper around __cancel_work_timer(). Which can sleep in the case where something else is concurrently trying to cancel the same delayed work, and as Thomas Gleixner pointed out on IRC, sleeping is a decidedly bad idea when you are invoked from take_cpu_down(), regardless of the state you leave interrupts in upon return.

Code inspection located no reason why the delayed work absolutely needed to be canceled from sched_tick_stop(): The work is not bound to the outgoing CPU by design, given that the whole point is to collect statistics without disturbing the outgoing CPU.

This commit therefore simply drops the cancel_delayed_work_sync() from sched_tick_stop(). Instead, a new ->state field is added to the tick_work structure so that the delayed-work handler function sched_tick_remote() can avoid reposting itself. A cpu_is_offline() check is also added to sched_tick_remote() to avoid mucking with the state of an offlined CPU (though it does appear safe to do so). The sched_tick_start() and sched_tick_stop() functions also update ->state, and sched_tick_start() also schedules the delayed work if ->state indicates that it is not already in flight.

[ paulmck: Apply Peter Zijlstra and Frederic Weisbecker atomics feedback. ]
Cc Linus Torvalds <[email protected]>
Cc Peter Zijlstra <[email protected]>
Cc Thomas Gleixner <[email protected]>
---
 kernel/sched/core.c | 57 ++++++++++++++++++++++++++++++++++++++-------
 1 file changed, 49 insertions(+), 8 deletions(-)
kernel/sched/core.c +49 -8
index df9f1fe5689b0..7fa8e74ad2ab4 100644
@@ -3486,8 +3486,36 @@ void scheduler_tick(void)
 
 struct tick_work {
 	int			cpu;
+	atomic_t		state;
 	struct delayed_work	work;
 };
+/* Values for ->state, see diagram below. */
+#define TICK_SCHED_REMOTE_OFFLINE	0
+#define TICK_SCHED_REMOTE_OFFLINING	1
+#define TICK_SCHED_REMOTE_RUNNING	2
+
+/*
+ * State diagram for ->state:
+ *
+ *
+ *          TICK_SCHED_REMOTE_OFFLINE
+ *                    |   ^
+ *                    |   |
+ *                    |   | sched_tick_remote()
+ *                    |   |
+ *                    |   |
+ *                    +--TICK_SCHED_REMOTE_OFFLINING
+ *                    |   ^
+ *                    |   |
+ * sched_tick_start() |   | sched_tick_stop()
+ *                    |   |
+ *                    V   |
+ *          TICK_SCHED_REMOTE_RUNNING
+ *
+ *
+ * Other transitions get WARN_ON_ONCE(), except that sched_tick_remote()
+ * and sched_tick_start() are happy to leave the state in RUNNING.
+ */
 
 static struct tick_work __percpu *tick_work_cpu;
 
@@ -3500,6 +3528,7 @@ static void sched_tick_remote(struct work_struct *work)
 	struct task_struct *curr;
 	struct rq_flags rf;
 	u64 delta;
+	int os;
 
 	/*
 	 * Handle the tick only if it appears the remote CPU is running in full
@@ -3513,7 +3542,7 @@ static void sched_tick_remote(struct work_struct *work)
 
 	rq_lock_irq(rq, &rf);
 	curr = rq->curr;
-	if (is_idle_task(curr))
+	if (is_idle_task(curr) || cpu_is_offline(cpu))
 		goto out_unlock;
 
 	update_rq_clock(rq);
@@ -3533,13 +3562,18 @@ static void sched_tick_remote(struct work_struct *work)
 	/*
 	 * Run the remote tick once per second (1Hz). This arbitrary
 	 * frequency is large enough to avoid overload but short enough
-	 * to keep scheduler internal stats reasonably up to date.
+	 * to keep scheduler internal stats reasonably up to date.  But
+	 * first update state to reflect hotplug activity if required.
 	 */
-	queue_delayed_work(system_unbound_wq, dwork, HZ);
+	os = atomic_fetch_add_unless(&twork->state, -1, TICK_SCHED_REMOTE_RUNNING);
+	WARN_ON_ONCE(os == TICK_SCHED_REMOTE_OFFLINE);
+	if (os == TICK_SCHED_REMOTE_RUNNING)
+		queue_delayed_work(system_unbound_wq, dwork, HZ);
 }
 
 static void sched_tick_start(int cpu)
 {
+	int os;
 	struct tick_work *twork;
 
 	if (housekeeping_cpu(cpu, HK_FLAG_TICK))
@@ -3548,15 +3582,20 @@ static void sched_tick_start(int cpu)
 	WARN_ON_ONCE(!tick_work_cpu);
 
 	twork = per_cpu_ptr(tick_work_cpu, cpu);
-	twork->cpu = cpu;
-	INIT_DELAYED_WORK(&twork->work, sched_tick_remote);
-	queue_delayed_work(system_unbound_wq, &twork->work, HZ);
+	os = atomic_xchg(&twork->state, TICK_SCHED_REMOTE_RUNNING);
+	WARN_ON_ONCE(os == TICK_SCHED_REMOTE_RUNNING);
+	if (os == TICK_SCHED_REMOTE_OFFLINE) {
+		twork->cpu = cpu;
+		INIT_DELAYED_WORK(&twork->work, sched_tick_remote);
+		queue_delayed_work(system_unbound_wq, &twork->work, HZ);
+	}
 }
 
 #ifdef CONFIG_HOTPLUG_CPU
 static void sched_tick_stop(int cpu)
 {
 	struct tick_work *twork;
+	int os;
 
 	if (housekeeping_cpu(cpu, HK_FLAG_TICK))
 		return;
@@ -3564,7 +3603,10 @@ static void sched_tick_stop(int cpu)
 	WARN_ON_ONCE(!tick_work_cpu);
 
 	twork = per_cpu_ptr(tick_work_cpu, cpu);
-	cancel_delayed_work_sync(&twork->work);
+	/* There cannot be competing actions, but don't rely on stop-machine. */
+	os = atomic_xchg(&twork->state, TICK_SCHED_REMOTE_OFFLINING);
+	WARN_ON_ONCE(os != TICK_SCHED_REMOTE_RUNNING);
+	/* Don't cancel, as this would mess up the state machine. */
 }
 #endif /* CONFIG_HOTPLUG_CPU */
 
@@ -3572,7 +3614,6 @@ int __init sched_tick_offload_init(void)
 {
 	tick_work_cpu = alloc_percpu(struct tick_work);
 	BUG_ON(!tick_work_cpu);
-
 	return 0;
 }
 
Signature · 1 line
2.20.1
author maintainer
#28 lore raw

PATCH 29/203 x86/reboot: Always use NMI fallback when shutdown via reboot vector IPI fails

In reply to Sasha Levin

From: Grzegorz Halat <[email protected]>

[ Upstream commit 747d5a1bf293dcb33af755a6d285d41b8c1ea010 ]

A reboot request sends an IPI via the reboot vector and waits for all other CPUs to stop. If one or more CPUs are in critical regions with interrupts disabled then the IPI is not handled on those CPUs and the shutdown hangs if native_stop_other_cpus() is called with the wait argument set.

Such a situation can happen when one CPU was stopped within a lock held section and another CPU is trying to acquire that lock with interrupts disabled. There are other scenarios which can cause such a lockup as well.

In theory the shutdown should be attempted by an NMI IPI after the timeout period elapsed. Though the wait loop after sending the reboot vector IPI prevents this. It checks the wait request argument and the timeout. If wait is set, which is true for sys_reboot() then it won't fall through to the NMI shutdown method after the timeout period has finished.

This was an oversight when the NMI shutdown mechanism was added to handle the 'reboot IPI is not working' situation. The mechanism was added to deal with stuck panic shutdowns, which do not have the wait request set, so the 'wait request' case was probably not considered.

Remove the wait check from the post reboot vector IPI wait loop and enforce that the wait loop in the NMI fallback path is invoked even if NMI IPIs are disabled or the registration of the NMI handler fails. That second wait loop will then hang if not all CPUs shutdown and the wait argument is set.

[ tglx: Avoid the hard to parse line break in the NMI fallback path,
add comments and massage the changelog ]

Fixes 7d007d21e539 ("x86/reboot: Use NMI to assist in shutting down if IRQ fails")
Cc Don Zickus <[email protected]>
---
 arch/x86/kernel/smp.c | 46 +++++++++++++++++++++++++------------------
 1 file changed, 27 insertions(+), 19 deletions(-)
arch/x86/kernel/smp.c +27 -19
index 96421f97e75cf..231fa230ebc73 100644
@@ -179,6 +179,12 @@ asmlinkage __visible void smp_reboot_interrupt(void)
 	irq_exit();
 }
 
+static int register_stop_handler(void)
+{
+	return register_nmi_handler(NMI_LOCAL, smp_stop_nmi_callback,
+				    NMI_FLAG_FIRST, "smp_stop");
+}
+
 static void native_stop_other_cpus(int wait)
 {
 	unsigned long flags;
@@ -212,39 +218,41 @@ static void native_stop_other_cpus(int wait)
 		apic->send_IPI_allbutself(REBOOT_VECTOR);
 
 		/*
-		 * Don't wait longer than a second if the caller
-		 * didn't ask us to wait.
+		 * Don't wait longer than a second for IPI completion. The
+		 * wait request is not checked here because that would
+		 * prevent an NMI shutdown attempt in case that not all
+		 * CPUs reach shutdown state.
 		 */
 		timeout = USEC_PER_SEC;
-		while (num_online_cpus() > 1 && (wait || timeout--))
+		while (num_online_cpus() > 1 && timeout--)
 			udelay(1);
 	}
-	
-	/* if the REBOOT_VECTOR didn't work, try with the NMI */
-	if ((num_online_cpus() > 1) && (!smp_no_nmi_ipi))  {
-		if (register_nmi_handler(NMI_LOCAL, smp_stop_nmi_callback,
-					 NMI_FLAG_FIRST, "smp_stop"))
-			/* Note: we ignore failures here */
-			/* Hope the REBOOT_IRQ is good enough */
-			goto finish;
-
-		/* sync above data before sending IRQ */
-		wmb();
 
-		pr_emerg("Shutting down cpus with NMI\n");
+	/* if the REBOOT_VECTOR didn't work, try with the NMI */
+	if (num_online_cpus() > 1) {
+		/*
+		 * If NMI IPI is enabled, try to register the stop handler
+		 * and send the IPI. In any case try to wait for the other
+		 * CPUs to stop.
+		 */
+		if (!smp_no_nmi_ipi && !register_stop_handler()) {
+			/* Sync above data before sending IRQ */
+			wmb();
 
-		apic->send_IPI_allbutself(NMI_VECTOR);
+			pr_emerg("Shutting down cpus with NMI\n");
 
+			apic->send_IPI_allbutself(NMI_VECTOR);
+		}
 		/*
-		 * Don't wait longer than a 10 ms if the caller
-		 * didn't ask us to wait.
+		 * Don't wait longer than 10 ms if the caller didn't
+		 * reqeust it. If wait is true, the machine hangs here if
+		 * one or more CPUs do not reach shutdown state.
 		 */
 		timeout = USEC_PER_MSEC * 10;
 		while (num_online_cpus() > 1 && (wait || timeout--))
 			udelay(1);
 	}
 
-finish:
 	local_irq_save(flags);
 	disable_local_APIC();
 	mcheck_cpu_clear(this_cpu_ptr(&cpu_info));
Signature · 1 line
2.20.1
author maintainer
#37 lore raw

PATCH 36/203 EDAC/mc: Fix grain_bits calculation

In reply to Sasha Levin

From: Robert Richter <[email protected]>

[ Upstream commit 3724ace582d9f675134985727fd5e9811f23c059 ]

The grain in EDAC is defined as "minimum granularity for an error report, in bytes". The following calculation of the grain_bits in edac_mc is wrong:

	grain_bits = fls_long(e->grain) + 1;

Where grain_bits is defined as:

grain = 1 << grain_bits

Example:

	grain = 8	# 64 bit (8 bytes)
	grain_bits = fls_long(8) + 1
	grain_bits = 4 + 1 = 5

	grain = 1 << grain_bits
	grain = 1 << 5 = 32

Replace it with the correct calculation:

	grain_bits = fls_long(e->grain - 1);

The example gives now:

	grain_bits = fls_long(8 - 1)
	grain_bits = fls_long(7)
	grain_bits = 3

	grain = 1 << 3 = 8

Also, check if the hardware reports a reasonable grain != 0 and fallback with a warning to 1 byte granularity otherwise.

[ bp: massage a bit. ]

---
 drivers/edac/edac_mc.c | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)
drivers/edac/edac_mc.c +6 -2
index 64922c8fa7e3b..d899d86897d06 100644
@@ -1235,9 +1235,13 @@ void edac_mc_handle_error(const enum hw_event_mc_err_type type,
 	if (p > e->location)
 		*(p - 1) = '\0';
 
-	/* Report the error via the trace interface */
-	grain_bits = fls_long(e->grain) + 1;
+	/* Sanity-check driver-supplied grain value. */
+	if (WARN_ON_ONCE(!e->grain))
+		e->grain = 1;
+
+	grain_bits = fls_long(e->grain - 1);
 
+	/* Report the error via the trace interface */
 	if (IS_ENABLED(CONFIG_RAS))
 		trace_mc_event(type, e->msg, e->label, e->error_count,
 			       mci->mc_idx, e->top_layer, e->mid_layer,
Signature · 1 line
2.20.1
author maintainer
#41 lore raw

PATCH 40/203 gpio: madera: Add support for Cirrus Logic CS47L15

In reply to Sasha Levin

From: Richard Fitzgerald <[email protected]>

[ Upstream commit d06be8bc290aa255b9fd8602e60fb9f487aa0f48 ]

As the gpio is common to all madera codecs all that is needed is to setup the correct number of GPIO pins for the CS47L15.

---
 drivers/gpio/gpio-madera.c | 3 +++
 1 file changed, 3 insertions(+)
drivers/gpio/gpio-madera.c +3 -0
index 4dbc837d12155..19db5a500eb0d 100644
@@ -136,6 +136,9 @@ static int madera_gpio_probe(struct platform_device *pdev)
 	madera_gpio->gpio_chip.parent = pdev->dev.parent;
 
 	switch (madera->type) {
+	case CS47L15:
+		madera_gpio->gpio_chip.ngpio = CS47L15_NUM_GPIOS;
+		break;
 	case CS47L35:
 		madera_gpio->gpio_chip.ngpio = CS47L35_NUM_GPIOS;
 		break;
Signature · 1 line
2.20.1
author maintainer
#42 lore raw

PATCH 41/203 gpio: madera: Add support for Cirrus Logic CS47L92

In reply to Sasha Levin

From: Charles Keepax <[email protected]>

[ Upstream commit 74d2d0e68701bcd53d2cf771dd3b3cb9f84bed5c ]

As the gpio is common to all madera codecs all that is needed is to setup the correct number of GPIO pins for the CS47L92.

---
 drivers/gpio/gpio-madera.c | 5 +++++
 1 file changed, 5 insertions(+)
drivers/gpio/gpio-madera.c +5 -0
index 19db5a500eb0d..be963113f6722 100644
@@ -150,6 +150,11 @@ static int madera_gpio_probe(struct platform_device *pdev)
 	case CS47L91:
 		madera_gpio->gpio_chip.ngpio = CS47L90_NUM_GPIOS;
 		break;
+	case CS42L92:
+	case CS47L92:
+	case CS47L93:
+		madera_gpio->gpio_chip.ngpio = CS47L92_NUM_GPIOS;
+		break;
 	default:
 		dev_err(&pdev->dev, "Unknown chip variant %d\n", madera->type);
 		return -EINVAL;
Signature · 1 line
2.20.1
author maintainer
#39 lore raw

PATCH 38/203 media: iguanair: add sanity checks

In reply to Sasha Levin

From: Oliver Neukum <[email protected]>

[ Upstream commit ab1cbdf159beba7395a13ab70bc71180929ca064 ]

The driver needs to check the endpoint types, too, as opposed to the number of endpoints. This also requires moving the check earlier.

---
 drivers/media/rc/iguanair.c | 15 +++++++--------
 1 file changed, 7 insertions(+), 8 deletions(-)
drivers/media/rc/iguanair.c +7 -8
index ea05e125016a7..872d6441e512c 100644
@@ -413,6 +413,10 @@ static int iguanair_probe(struct usb_interface *intf,
 	int ret, pipein, pipeout;
 	struct usb_host_interface *idesc;
 
+	idesc = intf->altsetting;
+	if (idesc->desc.bNumEndpoints < 2)
+		return -ENODEV;
+
 	ir = kzalloc(sizeof(*ir), GFP_KERNEL);
 	rc = rc_allocate_device(RC_DRIVER_IR_RAW);
 	if (!ir || !rc) {
@@ -427,18 +431,13 @@ static int iguanair_probe(struct usb_interface *intf,
 	ir->urb_in = usb_alloc_urb(0, GFP_KERNEL);
 	ir->urb_out = usb_alloc_urb(0, GFP_KERNEL);
 
-	if (!ir->buf_in || !ir->packet || !ir->urb_in || !ir->urb_out) {
+	if (!ir->buf_in || !ir->packet || !ir->urb_in || !ir->urb_out ||
+	    !usb_endpoint_is_int_in(&idesc->endpoint[0].desc) ||
+	    !usb_endpoint_is_int_out(&idesc->endpoint[1].desc)) {
 		ret = -ENOMEM;
 		goto out;
 	}
 
-	idesc = intf->altsetting;
-
-	if (idesc->desc.bNumEndpoints < 2) {
-		ret = -ENODEV;
-		goto out;
-	}
-
 	ir->rc = rc;
 	ir->dev = &intf->dev;
 	ir->udev = udev;
Signature · 1 line
2.20.1
author maintainer
#33 lore raw

PATCH 34/203 ASoC: meson: g12a-tohdmitx: override codec2codec params

In reply to Sasha Levin

From: Jerome Brunet <[email protected]>

[ Upstream commit 2c4956bc1e9062e5e3c5ea7612294f24e6d4fbdd ]

So far, forwarding the hw_params of the input to output relied on the .hw_params() callback of the cpu side of the codec2codec link to be called first. This is a bit weak.

Instead, override the stream params of the codec2codec to link to set it up correctly.

---
 sound/soc/meson/g12a-tohdmitx.c | 34 ++++++++++++++++-----------------
 1 file changed, 16 insertions(+), 18 deletions(-)
sound/soc/meson/g12a-tohdmitx.c +16 -18
index 707ccb192e4c2..9943c807ec5d7 100644
@@ -28,7 +28,7 @@
 #define  CTRL0_SPDIF_CLK_SEL		BIT(0)
 
 struct g12a_tohdmitx_input {
-	struct snd_pcm_hw_params params;
+	struct snd_soc_pcm_stream params;
 	unsigned int fmt;
 };
 
@@ -225,26 +225,17 @@ static int g12a_tohdmitx_input_hw_params(struct snd_pcm_substream *substream,
 {
 	struct g12a_tohdmitx_input *data = dai->playback_dma_data;
 
-	/* Save the stream params for the downstream link */
-	memcpy(&data->params, params, sizeof(*params));
+	data->params.rates = snd_pcm_rate_to_rate_bit(params_rate(params));
+	data->params.rate_min = params_rate(params);
+	data->params.rate_max = params_rate(params);
+	data->params.formats = 1 << params_format(params);
+	data->params.channels_min = params_channels(params);
+	data->params.channels_max = params_channels(params);
+	data->params.sig_bits = dai->driver->playback.sig_bits;
 
 	return 0;
 }
 
-static int g12a_tohdmitx_output_hw_params(struct snd_pcm_substream *substream,
-					  struct snd_pcm_hw_params *params,
-					  struct snd_soc_dai *dai)
-{
-	struct g12a_tohdmitx_input *in_data =
-		g12a_tohdmitx_get_input_data(dai->capture_widget);
-
-	if (!in_data)
-		return -ENODEV;
-
-	memcpy(params, &in_data->params, sizeof(*params));
-
-	return 0;
-}
 
 static int g12a_tohdmitx_input_set_fmt(struct snd_soc_dai *dai,
 				       unsigned int fmt)
@@ -266,6 +257,14 @@ static int g12a_tohdmitx_output_startup(struct snd_pcm_substream *substream,
 	if (!in_data)
 		return -ENODEV;
 
+	if (WARN_ON(!rtd->dai_link->params)) {
+		dev_warn(dai->dev, "codec2codec link expected\n");
+		return -EINVAL;
+	}
+
+	/* Replace link params with the input params */
+	rtd->dai_link->params = &in_data->params;
+
 	if (!in_data->fmt)
 		return 0;
 
@@ -278,7 +277,6 @@ static const struct snd_soc_dai_ops g12a_tohdmitx_input_ops = {
 };
 
 static const struct snd_soc_dai_ops g12a_tohdmitx_output_ops = {
-	.hw_params	= g12a_tohdmitx_output_hw_params,
 	.startup	= g12a_tohdmitx_output_startup,
 };
 
Signature · 7 lines
2.20.1


_______________________________________________
linux-amlogic mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-amlogic
author maintainer
#45 lore raw

PATCH 44/203 base: soc: Export soc_device_register/unregister APIs

In reply to Sasha Levin

From: Vinod Koul <[email protected]>

[ Upstream commit f7ccc7a397cf2ef64aebb2f726970b93203858d2 ]

Qcom Socinfo driver can be built as a module, so
export these two APIs.

---
 drivers/base/soc.c | 2 ++
 1 file changed, 2 insertions(+)
drivers/base/soc.c +2 -0
index 10b280f30217b..7e91894a380b5 100644
@@ -157,6 +157,7 @@ struct soc_device *soc_device_register(struct soc_device_attribute *soc_dev_attr
 out1:
 	return ERR_PTR(ret);
 }
+EXPORT_SYMBOL_GPL(soc_device_register);
 
 /* Ensure soc_dev->attr is freed prior to calling soc_device_unregister. */
 void soc_device_unregister(struct soc_device *soc_dev)
@@ -166,6 +167,7 @@ void soc_device_unregister(struct soc_device *soc_dev)
 	device_unregister(&soc_dev->dev);
 	early_soc_dev_attr = NULL;
 }
+EXPORT_SYMBOL_GPL(soc_device_unregister);
 
 static int __init soc_bus_register(void)
 {
Signature · 1 line
2.20.1
author maintainer
#44 lore raw

PATCH 43/203 soc: amlogic: meson-clk-measure: protect measure with a mutex

In reply to Sasha Levin

From: Neil Armstrong <[email protected]>

[ Upstream commit 3a760d986568b67d1f8411dab64608075817b90d ]

In order to protect clock measuring when multiple process asks for a measure, protect the main measure function with mutexes.

---
 drivers/soc/amlogic/meson-clk-measure.c | 12 +++++++++++-
 1 file changed, 11 insertions(+), 1 deletion(-)
drivers/soc/amlogic/meson-clk-measure.c +11 -1
index 19d4cbc93a17a..c470e24f1dfa6 100644
@@ -11,6 +11,8 @@
 #include <linux/debugfs.h>
 #include <linux/regmap.h>
 
+static DEFINE_MUTEX(measure_lock);
+
 #define MSR_CLK_DUTY		0x0
 #define MSR_CLK_REG0		0x4
 #define MSR_CLK_REG1		0x8
@@ -360,6 +362,10 @@ static int meson_measure_id(struct meson_msr_id *clk_msr_id,
 	unsigned int val;
 	int ret;
 
+	ret = mutex_lock_interruptible(&measure_lock);
+	if (ret)
+		return ret;
+
 	regmap_write(priv->regmap, MSR_CLK_REG0, 0);
 
 	/* Set measurement duration */
@@ -377,8 +383,10 @@ static int meson_measure_id(struct meson_msr_id *clk_msr_id,
 
 	ret = regmap_read_poll_timeout(priv->regmap, MSR_CLK_REG0,
 				       val, !(val & MSR_BUSY), 10, 10000);
-	if (ret)
+	if (ret) {
+		mutex_unlock(&measure_lock);
 		return ret;
+	}
 
 	/* Disable */
 	regmap_update_bits(priv->regmap, MSR_CLK_REG0, MSR_ENABLE, 0);
@@ -386,6 +394,8 @@ static int meson_measure_id(struct meson_msr_id *clk_msr_id,
 	/* Get the value in multiple of gate time counts */
 	regmap_read(priv->regmap, MSR_CLK_REG2, &val);
 
+	mutex_unlock(&measure_lock);
+
 	if (val >= MSR_VAL_MASK)
 		return -EINVAL;
 
Signature · 7 lines
2.20.1


_______________________________________________
linux-amlogic mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-amlogic
author maintainer
#54 lore raw

PATCH 53/203 media: media/platform: fsl-viu.c: fix build for MICROBLAZE

In reply to Sasha Levin

From: Randy Dunlap <[email protected]>

[ Upstream commit 6898dd580a045341f844862ceb775144156ec1af ]

arch/microblaze/ defines out_be32() and in_be32(), so don't do that again in the driver source.

Fixes these build warnings:

../drivers/media/platform/fsl-viu.c:36: warning: "out_be32" redefined ../arch/microblaze/include/asm/io.h:50: note: this is the location of the previous definition ../drivers/media/platform/fsl-viu.c:37: warning: "in_be32" redefined ../arch/microblaze/include/asm/io.h:53: note: this is the location of the previous definition

Fixes 29d750686331 ("media: fsl-viu: allow building it with COMPILE_TEST")
---
 drivers/media/platform/fsl-viu.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/media/platform/fsl-viu.c +1 -1
index 691be788e38b3..b74e4f50d7d9f 100644
@@ -32,7 +32,7 @@
 #define VIU_VERSION		"0.5.1"
 
 /* Allow building this driver with COMPILE_TEST */
-#ifndef CONFIG_PPC
+#if !defined(CONFIG_PPC) && !defined(CONFIG_MICROBLAZE)
 #define out_be32(v, a)	iowrite32be(a, (void __iomem *)v)
 #define in_be32(a)	ioread32be((void __iomem *)a)
 #endif
Signature · 1 line
2.20.1
author maintainer
#57 lore raw

PATCH 56/203 RAS: Build debugfs.o only when enabled in Kconfig

In reply to Sasha Levin

From: Valdis Kletnieks <[email protected]>

[ Upstream commit b6ff24f7b5101101ff897dfdde3f37924e676bc2 ]

In addition, the 0day bot reported this build error:

Quoted 1 line
Quoted 1 line

drivers/ras/debugfs.c:10:5: error: redefinition of 'ras_userspace_consumers'

      int ras_userspace_consumers(void)
          ^~~~~~~~~~~~~~~~~~~~~~~
     In file included from drivers/ras/debugfs.c:3:0:
     include/linux/ras.h:14:19: note: previous definition of 'ras_userspace_consumers' was here
      static inline int ras_userspace_consumers(void) { return 0; }
                      ^~~~~~~~~~~~~~~~~~~~~~~

for a riscv-specific .config where CONFIG_DEBUG_FS is not set. Fix all that by making debugfs.o depend on that define.

[ bp: Rewrite commit message. ]

---
 drivers/ras/Makefile | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/ras/Makefile +2 -1
index ef6777e14d3df..6f0404f501071 100644
@@ -1,3 +1,4 @@
 # SPDX-License-Identifier: GPL-2.0-only
-obj-$(CONFIG_RAS)	+= ras.o debugfs.o
+obj-$(CONFIG_RAS)	+= ras.o
+obj-$(CONFIG_DEBUG_FS)	+= debugfs.o
 obj-$(CONFIG_RAS_CEC)	+= cec.o
Signature · 1 line
2.20.1
author maintainer
#58 lore raw

PATCH 57/203 ASoC: hdac_hda: fix page fault issue by removing race

In reply to Sasha Levin

From: Keyon Jie <[email protected]>

[ Upstream commit 804cbf4bb063204ca6c2471baa694548aab02ce3 ]

There is a race between hda codec device removing and the jack-detecting work, which will lead to a page fault issue as the latter work is accessing codec device which could be already removed.

Here add the cancellation of jack-detecting work before codecs are actually removed to avoid the race and fix the issue.

---
 sound/soc/codecs/hdac_hda.c | 4 ++++
 1 file changed, 4 insertions(+)
sound/soc/codecs/hdac_hda.c +4 -0
index 7d49402569149..91242b6f8ea7a 100644
@@ -495,6 +495,10 @@ static int hdac_hda_dev_probe(struct hdac_device *hdev)
 
 static int hdac_hda_dev_remove(struct hdac_device *hdev)
 {
+	struct hdac_hda_priv *hda_pvt;
+
+	hda_pvt = dev_get_drvdata(&hdev->dev);
+	cancel_delayed_work_sync(&hda_pvt->codec.jackpoll_work);
 	return 0;
 }
 
Signature · 1 line
2.20.1
author maintainer
#60 lore raw

PATCH 59/203 loop: Add LOOP_SET_DIRECT_IO to compat ioctl

In reply to Sasha Levin

From: Alessio Balsini <[email protected]>

[ Upstream commit fdbe4eeeb1aac219b14f10c0ed31ae5d1123e9b8 ]

Enabling Direct I/O with loop devices helps reducing memory usage by avoiding double caching. 32 bit applications running on 64 bits systems are currently not able to request direct I/O because is missing from the lo_compat_ioctl.

This patch fixes the compatibility issue mentioned above by exporting LOOP_SET_DIRECT_IO as additional lo_compat_ioctl() entry. The input argument for this ioctl is a single long converted to a 1-bit boolean, so compatibility is preserved.

---
 drivers/block/loop.c | 1 +
 1 file changed, 1 insertion(+)
drivers/block/loop.c +1 -0
index ab7ca5989097a..1410fa8936538 100644
@@ -1755,6 +1755,7 @@ static int lo_compat_ioctl(struct block_device *bdev, fmode_t mode,
 	case LOOP_SET_FD:
 	case LOOP_CHANGE_FD:
 	case LOOP_SET_BLOCK_SIZE:
+	case LOOP_SET_DIRECT_IO:
 		err = lo_ioctl(bdev, mode, cmd, arg);
 		break;
 	default:
Signature · 1 line
2.20.1
author maintainer
#63 lore raw

PATCH 62/203 efi: cper: print AER info of PCIe fatal error

In reply to Sasha Levin

From: Xiaofei Tan <[email protected]>

[ Upstream commit b194a77fcc4001dc40aecdd15d249648e8a436d1 ]

AER info of PCIe fatal error is not printed in the current driver. Because APEI driver will panic directly for fatal error, and can't run to the place of printing AER info.

An example log is as following:
{763}[Hardware Error]: Hardware error from APEI Generic Hardware Error Source: 11 {763}[Hardware Error]: event severity: fatal
{763}[Hardware Error]: Error 0, type: fatal

{763}[Hardware Error]:   section_type: PCIe error
{763}[Hardware Error]:   port_type: 0, PCIe end point
{763}[Hardware Error]:   version: 4.0
{763}[Hardware Error]:   command: 0x0000, status: 0x0010
{763}[Hardware Error]:   device_id: 0000:82:00.0
{763}[Hardware Error]:   slot: 0
{763}[Hardware Error]:   secondary_bus: 0x00
{763}[Hardware Error]:   vendor_id: 0x8086, device_id: 0x10fb
{763}[Hardware Error]:   class_code: 000002
Kernel panic - not syncing: Fatal hardware error!

This issue was imported by the patch, '37448adfc7ce ("aerdrv: Move cper_print_aer() call out of interrupt context")'. To fix this issue, this patch adds print of AER info in cper_print_pcie() for fatal error.

Here is the example log after this patch applied:
{24}[Hardware Error]: Hardware error from APEI Generic Hardware Error Source: 10 {24}[Hardware Error]: event severity: fatal
{24}[Hardware Error]: Error 0, type: fatal

{24}[Hardware Error]:   section_type: PCIe error
{24}[Hardware Error]:   port_type: 0, PCIe end point
{24}[Hardware Error]:   version: 4.0
{24}[Hardware Error]:   command: 0x0546, status: 0x4010
{24}[Hardware Error]:   device_id: 0000:01:00.0
{24}[Hardware Error]:   slot: 0
{24}[Hardware Error]:   secondary_bus: 0x00
{24}[Hardware Error]:   vendor_id: 0x15b3, device_id: 0x1019
{24}[Hardware Error]:   class_code: 000002
{24}[Hardware Error]:   aer_uncor_status: 0x00040000, aer_uncor_mask: 0x00000000
{24}[Hardware Error]:   aer_uncor_severity: 0x00062010
{24}[Hardware Error]:   TLP Header: 000000c0 01010000 00000001 00000000
Kernel panic - not syncing: Fatal hardware error!
Fixes 37448adfc7ce ("aerdrv: Move cper_print_aer() call out of interrupt context")
[ardb: put parens around terms of && operator]
---
 drivers/firmware/efi/cper.c | 15 +++++++++++++++
 1 file changed, 15 insertions(+)
drivers/firmware/efi/cper.c +15 -0
index 8fa977c7861f9..addf0749dd8b6 100644
@@ -390,6 +390,21 @@ static void cper_print_pcie(const char *pfx, const struct cper_sec_pcie *pcie,
 		printk(
 	"%s""bridge: secondary_status: 0x%04x, control: 0x%04x\n",
 	pfx, pcie->bridge.secondary_status, pcie->bridge.control);
+
+	/* Fatal errors call __ghes_panic() before AER handler prints this */
+	if ((pcie->validation_bits & CPER_PCIE_VALID_AER_INFO) &&
+	    (gdata->error_severity & CPER_SEV_FATAL)) {
+		struct aer_capability_regs *aer;
+
+		aer = (struct aer_capability_regs *)pcie->aer_info;
+		printk("%saer_uncor_status: 0x%08x, aer_uncor_mask: 0x%08x\n",
+		       pfx, aer->uncor_status, aer->uncor_mask);
+		printk("%saer_uncor_severity: 0x%08x\n",
+		       pfx, aer->uncor_severity);
+		printk("%sTLP Header: %08x %08x %08x %08x\n", pfx,
+		       aer->header_log.dw0, aer->header_log.dw1,
+		       aer->header_log.dw2, aer->header_log.dw3);
+	}
 }
 
 static void cper_print_tstamp(const char *pfx,
Signature · 1 line
2.20.1
author maintainer
#62 lore raw

PATCH 61/203 EDAC, pnd2: Fix ioremap() size in dnv_rd_reg()

In reply to Sasha Levin

From: Stephen Douthit <[email protected]>

[ Upstream commit 29a3388bfcce7a6d087051376ea02bf8326a957b ]

Depending on how BIOS has marked the reserved region containing the 32KB MCHBAR you can get warnings like:

resource sanity check: requesting [mem 0xfed10000-0xfed1ffff], which spans more than reserved [mem 0xfed10000-0xfed17fff] caller dnv_rd_reg+0xc8/0x240 [pnd2_edac] mapping multiple BARs

Not all of the mmio regions used in dnv_rd_reg() are the same size. The MCHBAR window is 32KB and the sideband ports are 64KB. Pass the correct size to ioremap() depending on which resource we're reading from.

---
 drivers/edac/pnd2_edac.c | 7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)
drivers/edac/pnd2_edac.c +6 -1
index ca25f8fe57ef3..1ad538baaa4a9 100644
@@ -260,11 +260,14 @@ static u64 get_sideband_reg_base_addr(void)
 	}
 }
 
+#define DNV_MCHBAR_SIZE  0x8000
+#define DNV_SB_PORT_SIZE 0x10000
 static int dnv_rd_reg(int port, int off, int op, void *data, size_t sz, char *name)
 {
 	struct pci_dev *pdev;
 	char *base;
 	u64 addr;
+	unsigned long size;
 
 	if (op == 4) {
 		pdev = pci_get_device(PCI_VENDOR_ID_INTEL, 0x1980, NULL);
@@ -279,15 +282,17 @@ static int dnv_rd_reg(int port, int off, int op, void *data, size_t sz, char *na
 			addr = get_mem_ctrl_hub_base_addr();
 			if (!addr)
 				return -ENODEV;
+			size = DNV_MCHBAR_SIZE;
 		} else {
 			/* MMIO via sideband register base address */
 			addr = get_sideband_reg_base_addr();
 			if (!addr)
 				return -ENODEV;
 			addr += (port << 16);
+			size = DNV_SB_PORT_SIZE;
 		}
 
-		base = ioremap((resource_size_t)addr, 0x10000);
+		base = ioremap((resource_size_t)addr, size);
 		if (!base)
 			return -ENODEV;
 
Signature · 1 line
2.20.1
author maintainer
#64 lore raw

PATCH 63/203 firmware: arm_scmi: Check if platform has released shmem before using

In reply to Sasha Levin

From: Sudeep Holla <[email protected]>

[ Upstream commit 9dc34d635c67e57051853855c43249408641a5ab ]

Sometimes platfom may take too long to respond to the command and OS might timeout before platform transfer the ownership of the shared memory region to the OS with the response.

Since the mailbox channel associated with the channel is freed and new commands are dispatch on the same channel, OS needs to wait until it gets back the ownership. If not, either OS may end up overwriting the platform response for the last command(which is fine as OS timed out that command) or platform might overwrite the payload for the next command with the response for the old.

The latter is problematic as platform may end up interpretting the response as the payload. In order to avoid such race, let's wait until the OS gets back the ownership before we prepare the shared memory with the payload for the next command.

---
 drivers/firmware/arm_scmi/driver.c | 8 ++++++++
 1 file changed, 8 insertions(+)
drivers/firmware/arm_scmi/driver.c +8 -0
index b5bc4c7a8fab2..b49c9e6f4bf10 100644
@@ -271,6 +271,14 @@ static void scmi_tx_prepare(struct mbox_client *cl, void *m)
 	struct scmi_chan_info *cinfo = client_to_scmi_chan_info(cl);
 	struct scmi_shared_mem __iomem *mem = cinfo->payload;
 
+	/*
+	 * Ideally channel must be free by now unless OS timeout last
+	 * request and platform continued to process the same, wait
+	 * until it releases the shared memory, otherwise we may endup
+	 * overwriting its response with new message payload or vice-versa
+	 */
+	spin_until_cond(ioread32(&mem->channel_status) &
+			SCMI_SHMEM_CHAN_STAT_CHANNEL_FREE);
 	/* Mark channel busy + clear error */
 	iowrite32(0x0, &mem->channel_status);
 	iowrite32(t->hdr.poll_completion ? 0 : SCMI_SHMEM_FLAG_INTR_ENABLED,
Signature · 1 line
2.20.1
author maintainer
#67 lore raw

PATCH 66/203 blk-mq: Fix memory leak in blk_mq_init_allocated_queue error handling

In reply to Sasha Levin

From: zhengbin <[email protected]>

[ Upstream commit 73d9c8d4c0017e21e1ff519474ceb1450484dc9a ]

If blk_mq_init_allocated_queue->elevator_init_mq fails, need to release the previously requested resources.

Fixes d34849913819 ("blk-mq-sched: allow setting of default IO scheduler")
---
 block/blk-mq.c | 9 ++++++---
 1 file changed, 6 insertions(+), 3 deletions(-)
block/blk-mq.c +6 -3
index 0835f4d8d42e7..a38ebb2a380c2 100644
@@ -2841,6 +2841,8 @@ static unsigned int nr_hw_queues(struct blk_mq_tag_set *set)
 struct request_queue *blk_mq_init_allocated_queue(struct blk_mq_tag_set *set,
 						  struct request_queue *q)
 {
+	int ret = -ENOMEM;
+
 	/* mark the queue as mq asap */
 	q->mq_ops = set->ops;
 
@@ -2902,17 +2904,18 @@ struct request_queue *blk_mq_init_allocated_queue(struct blk_mq_tag_set *set,
 	blk_mq_map_swqueue(q);
 
 	if (!(set->flags & BLK_MQ_F_NO_SCHED)) {
-		int ret;
-
 		ret = elevator_init_mq(q);
 		if (ret)
-			return ERR_PTR(ret);
+			goto err_tag_set;
 	}
 
 	return q;
 
+err_tag_set:
+	blk_mq_del_queue_tag_set(q);
 err_hctxs:
 	kfree(q->queue_hw_ctx);
+	q->nr_hw_queues = 0;
 err_sys_init:
 	blk_mq_sysfs_deinit(q);
 err_poll:
Signature · 1 line
2.20.1
author maintainer
#68 lore raw

PATCH 67/203 media: gspca: zero usb_buf on error

In reply to Sasha Levin

From: Hans Verkuil <[email protected]>

[ Upstream commit 4843a543fad3bf8221cf14e5d5f32d15cee89e84 ]

If reg_r() fails, then gspca_dev->usb_buf was left uninitialized, and some drivers used the contents of that buffer in logic.

This caused several syzbot errors:

https://syzkaller.appspot.com/bug?extid=397fd082ce5143e2f67d
https://syzkaller.appspot.com/bug?extid=1a35278dd0ebfb3a038a
https://syzkaller.appspot.com/bug?extid=06ddf1788cfd048c5e82

I analyzed the gspca drivers and zeroed the buffer where needed.

Reported-and-tested-by [email protected]
Reported-and-tested-by [email protected]
Reported-and-tested-by [email protected]
---
 drivers/media/usb/gspca/konica.c   |  5 +++++
 drivers/media/usb/gspca/nw80x.c    |  5 +++++
 drivers/media/usb/gspca/ov519.c    | 10 ++++++++++
 drivers/media/usb/gspca/ov534.c    |  5 +++++
 drivers/media/usb/gspca/ov534_9.c  |  1 +
 drivers/media/usb/gspca/se401.c    |  5 +++++
 drivers/media/usb/gspca/sn9c20x.c  |  5 +++++
 drivers/media/usb/gspca/sonixb.c   |  5 +++++
 drivers/media/usb/gspca/sonixj.c   |  5 +++++
 drivers/media/usb/gspca/spca1528.c |  5 +++++
 drivers/media/usb/gspca/sq930x.c   |  5 +++++
 drivers/media/usb/gspca/sunplus.c  |  5 +++++
 drivers/media/usb/gspca/vc032x.c   |  5 +++++
 drivers/media/usb/gspca/w996Xcf.c  |  5 +++++
 14 files changed, 71 insertions(+)
drivers/media/usb/gspca/konica.c +5 -0
index d8e40137a2043..53db9a2895ea5 100644
@@ -114,6 +114,11 @@ static void reg_r(struct gspca_dev *gspca_dev, u16 value, u16 index)
 	if (ret < 0) {
 		pr_err("reg_r err %d\n", ret);
 		gspca_dev->usb_err = ret;
+		/*
+		 * Make sure the buffer is zeroed to avoid uninitialized
+		 * values.
+		 */
+		memset(gspca_dev->usb_buf, 0, 2);
 	}
 }
 
drivers/media/usb/gspca/nw80x.c +5 -0
index 59649704beba1..880f569bda30f 100644
@@ -1572,6 +1572,11 @@ static void reg_r(struct gspca_dev *gspca_dev,
 	if (ret < 0) {
 		pr_err("reg_r err %d\n", ret);
 		gspca_dev->usb_err = ret;
+		/*
+		 * Make sure the buffer is zeroed to avoid uninitialized
+		 * values.
+		 */
+		memset(gspca_dev->usb_buf, 0, USB_BUF_SZ);
 		return;
 	}
 	if (len == 1)
drivers/media/usb/gspca/ov519.c +10 -0
index cfb1f53bc17e7..f417dfc0b8729 100644
@@ -2073,6 +2073,11 @@ static int reg_r(struct sd *sd, u16 index)
 	} else {
 		gspca_err(gspca_dev, "reg_r %02x failed %d\n", index, ret);
 		sd->gspca_dev.usb_err = ret;
+		/*
+		 * Make sure the result is zeroed to avoid uninitialized
+		 * values.
+		 */
+		gspca_dev->usb_buf[0] = 0;
 	}
 
 	return ret;
@@ -2101,6 +2106,11 @@ static int reg_r8(struct sd *sd,
 	} else {
 		gspca_err(gspca_dev, "reg_r8 %02x failed %d\n", index, ret);
 		sd->gspca_dev.usb_err = ret;
+		/*
+		 * Make sure the buffer is zeroed to avoid uninitialized
+		 * values.
+		 */
+		memset(gspca_dev->usb_buf, 0, 8);
 	}
 
 	return ret;
drivers/media/usb/gspca/ov534.c +5 -0
index 56521c991db45..185c1f10fb30b 100644
@@ -693,6 +693,11 @@ static u8 ov534_reg_read(struct gspca_dev *gspca_dev, u16 reg)
 	if (ret < 0) {
 		pr_err("read failed %d\n", ret);
 		gspca_dev->usb_err = ret;
+		/*
+		 * Make sure the result is zeroed to avoid uninitialized
+		 * values.
+		 */
+		gspca_dev->usb_buf[0] = 0;
 	}
 	return gspca_dev->usb_buf[0];
 }
drivers/media/usb/gspca/ov534_9.c +1 -0
index 867f860a96500..91efc650cf769 100644
@@ -1145,6 +1145,7 @@ static u8 reg_r(struct gspca_dev *gspca_dev, u16 reg)
 	if (ret < 0) {
 		pr_err("reg_r err %d\n", ret);
 		gspca_dev->usb_err = ret;
+		return 0;
 	}
 	return gspca_dev->usb_buf[0];
 }
drivers/media/usb/gspca/se401.c +5 -0
index 061deee138c31..e087cfb5980b0 100644
@@ -101,6 +101,11 @@ static void se401_read_req(struct gspca_dev *gspca_dev, u16 req, int silent)
 			pr_err("read req failed req %#04x error %d\n",
 			       req, err);
 		gspca_dev->usb_err = err;
+		/*
+		 * Make sure the buffer is zeroed to avoid uninitialized
+		 * values.
+		 */
+		memset(gspca_dev->usb_buf, 0, READ_REQ_SIZE);
 	}
 }
 
drivers/media/usb/gspca/sn9c20x.c +5 -0
index b43f89fee6c1d..12a2395a36ac6 100644
@@ -909,6 +909,11 @@ static void reg_r(struct gspca_dev *gspca_dev, u16 reg, u16 length)
 	if (unlikely(result < 0 || result != length)) {
 		pr_err("Read register %02x failed %d\n", reg, result);
 		gspca_dev->usb_err = result;
+		/*
+		 * Make sure the buffer is zeroed to avoid uninitialized
+		 * values.
+		 */
+		memset(gspca_dev->usb_buf, 0, USB_BUF_SZ);
 	}
 }
 
drivers/media/usb/gspca/sonixb.c +5 -0
index 046fc2c2a1350..4d655e2da9cba 100644
@@ -453,6 +453,11 @@ static void reg_r(struct gspca_dev *gspca_dev,
 		dev_err(gspca_dev->v4l2_dev.dev,
 			"Error reading register %02x: %d\n", value, res);
 		gspca_dev->usb_err = res;
+		/*
+		 * Make sure the result is zeroed to avoid uninitialized
+		 * values.
+		 */
+		gspca_dev->usb_buf[0] = 0;
 	}
 }
 
drivers/media/usb/gspca/sonixj.c +5 -0
index 50a6c8425827f..2e1bd2df8304a 100644
@@ -1162,6 +1162,11 @@ static void reg_r(struct gspca_dev *gspca_dev,
 	if (ret < 0) {
 		pr_err("reg_r err %d\n", ret);
 		gspca_dev->usb_err = ret;
+		/*
+		 * Make sure the buffer is zeroed to avoid uninitialized
+		 * values.
+		 */
+		memset(gspca_dev->usb_buf, 0, USB_BUF_SZ);
 	}
 }
 
drivers/media/usb/gspca/spca1528.c +5 -0
index 2ae03b60163ff..ccc477944ef82 100644
@@ -71,6 +71,11 @@ static void reg_r(struct gspca_dev *gspca_dev,
 	if (ret < 0) {
 		pr_err("reg_r err %d\n", ret);
 		gspca_dev->usb_err = ret;
+		/*
+		 * Make sure the buffer is zeroed to avoid uninitialized
+		 * values.
+		 */
+		memset(gspca_dev->usb_buf, 0, USB_BUF_SZ);
 	}
 }
 
drivers/media/usb/gspca/sq930x.c +5 -0
index d1ba0888d7989..c3610247a90e0 100644
@@ -425,6 +425,11 @@ static void reg_r(struct gspca_dev *gspca_dev,
 	if (ret < 0) {
 		pr_err("reg_r %04x failed %d\n", value, ret);
 		gspca_dev->usb_err = ret;
+		/*
+		 * Make sure the buffer is zeroed to avoid uninitialized
+		 * values.
+		 */
+		memset(gspca_dev->usb_buf, 0, USB_BUF_SZ);
 	}
 }
 
drivers/media/usb/gspca/sunplus.c +5 -0
index d0ddfa957ca9f..f4a4222f0d2e4 100644
@@ -255,6 +255,11 @@ static void reg_r(struct gspca_dev *gspca_dev,
 	if (ret < 0) {
 		pr_err("reg_r err %d\n", ret);
 		gspca_dev->usb_err = ret;
+		/*
+		 * Make sure the buffer is zeroed to avoid uninitialized
+		 * values.
+		 */
+		memset(gspca_dev->usb_buf, 0, USB_BUF_SZ);
 	}
 }
 
drivers/media/usb/gspca/vc032x.c +5 -0
index 588a847ea4834..4cb7c92ea1328 100644
@@ -2906,6 +2906,11 @@ static void reg_r_i(struct gspca_dev *gspca_dev,
 	if (ret < 0) {
 		pr_err("reg_r err %d\n", ret);
 		gspca_dev->usb_err = ret;
+		/*
+		 * Make sure the buffer is zeroed to avoid uninitialized
+		 * values.
+		 */
+		memset(gspca_dev->usb_buf, 0, USB_BUF_SZ);
 	}
 }
 static void reg_r(struct gspca_dev *gspca_dev,
drivers/media/usb/gspca/w996Xcf.c +5 -0
index 16b679c2de21f..a8350ee9712fb 100644
@@ -133,6 +133,11 @@ static int w9968cf_read_sb(struct sd *sd)
 	} else {
 		pr_err("Read SB reg [01] failed\n");
 		sd->gspca_dev.usb_err = ret;
+		/*
+		 * Make sure the buffer is zeroed to avoid uninitialized
+		 * values.
+		 */
+		memset(sd->gspca_dev.usb_buf, 0, 2);
 	}
 
 	udelay(W9968CF_I2C_BUS_DELAY);
Signature · 1 line
2.20.1
author maintainer
#70 lore raw

PATCH 69/203 perf test vfs_getname: Disable ~/.perfconfig to get default output

In reply to Sasha Levin

From: Arnaldo Carvalho de Melo <[email protected]>

[ Upstream commit 4fe94ce1c6ba678b5f12b94bb9996eea4fc99e85 ]

To get the expected output we have to ignore whatever changes the user has in its ~/.perfconfig file, so set PERF_CONFIG to /dev/null to achieve that.

Before:

  # egrep 'trace|show_' ~/.perfconfig
  [trace]
  	show_zeros = yes
  	show_duration = no
  	show_timestamp = no
  	show_arg_names = no
  	show_prefix = yes
  # echo $PERF_CONFIG
  # perf test "trace + vfs_getname"
  70: Check open filename arg using perf trace + vfs_getname: FAILED!
  # export PERF_CONFIG=/dev/null
  # perf test "trace + vfs_getname"
  70: Check open filename arg using perf trace + vfs_getname: Ok
  #

After:

  # egrep 'trace|show_' ~/.perfconfig
  [trace]
  	show_zeros = yes
  	show_duration = no
  	show_timestamp = no
  	show_arg_names = no
  	show_prefix = yes
  # echo $PERF_CONFIG
  # perf test "trace + vfs_getname"
  70: Check open filename arg using perf trace + vfs_getname: Ok
  #
---
 tools/perf/tests/shell/trace+probe_vfs_getname.sh | 4 ++++
 1 file changed, 4 insertions(+)
tools/perf/tests/shell/trace+probe_vfs_getname.sh +4 -0
index 45d269b0157eb..11cc2af13f2bb 100755
@@ -32,6 +32,10 @@ if [ $err -ne 0 ] ; then
 	exit $err
 fi
 
+# Do not use whatever ~/.perfconfig file, it may change the output
+# via trace.{show_timestamp,show_prefix,etc}
+export PERF_CONFIG=/dev/null
+
 trace_open_vfs_getname
 err=$?
 rm -f ${file}
Signature · 1 line
2.20.1
author maintainer
#74 lore raw

PATCH 73/203 media: em28xx: modules workqueue not inited for 2nd device

In reply to Sasha Levin

From: Sean Young <[email protected]>

[ Upstream commit 46e4a26615cc7854340e4b69ca59ee78d6f20c8b ]

syzbot reports an error on flush_request_modules() for the second device. This workqueue was never initialised so simply remove the offending line.

usb 1-1: USB disconnect, device number 2
em28xx 1-1:1.153: Disconnecting em28xx #1

------------[ cut here ]------------
WARNING: CPU: 0 PID: 12 at kernel/workqueue.c:3031
__flush_work.cold+0x2c/0x36 kernel/workqueue.c:3031
Kernel panic - not syncing: panic_on_warn set ...
CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.3.0-rc2+ #25
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
  __dump_stack lib/dump_stack.c:77 [inline]
  dump_stack+0xca/0x13e lib/dump_stack.c:113
  panic+0x2a3/0x6da kernel/panic.c:219
  __warn.cold+0x20/0x4a kernel/panic.c:576
  report_bug+0x262/0x2a0 lib/bug.c:186
  fixup_bug arch/x86/kernel/traps.c:179 [inline]
  fixup_bug arch/x86/kernel/traps.c:174 [inline]
  do_error_trap+0x12b/0x1e0 arch/x86/kernel/traps.c:272
  do_invalid_op+0x32/0x40 arch/x86/kernel/traps.c:291
  invalid_op+0x23/0x30 arch/x86/entry/entry_64.S:1026
RIP: 0010:__flush_work.cold+0x2c/0x36 kernel/workqueue.c:3031
Code: 9a 22 00 48 c7 c7 20 e4 c5 85 e8 d9 3a 0d 00 0f 0b 45 31 e4 e9 98 86

ff ff e8 51 9a 22 00 48 c7 c7 20 e4 c5 85 e8 be 3a 0d 00 <0f> 0b 45 31 e4 e9 7d 86 ff ff e8 36 9a 22 00 48 c7 c7 20 e4 c5 85
RSP: 0018:ffff8881da20f720 EFLAGS: 00010286
RAX: 0000000000000024 RBX: dffffc0000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffffff8128a0fd RDI: ffffed103b441ed6
RBP: ffff8881da20f888 R08: 0000000000000024 R09: fffffbfff11acd9a
R10: fffffbfff11acd99 R11: ffffffff88d66ccf R12: 0000000000000000
R13: 0000000000000001 R14: ffff8881c6685df8 R15: ffff8881d2a85b78

  flush_request_modules drivers/media/usb/em28xx/em28xx-cards.c:3325 [inline]
  em28xx_usb_disconnect.cold+0x280/0x2a6
drivers/media/usb/em28xx/em28xx-cards.c:4023
  usb_unbind_interface+0x1bd/0x8a0 drivers/usb/core/driver.c:423
  __device_release_driver drivers/base/dd.c:1120 [inline]
  device_release_driver_internal+0x404/0x4c0 drivers/base/dd.c:1151
  bus_remove_device+0x2dc/0x4a0 drivers/base/bus.c:556
  device_del+0x420/0xb10 drivers/base/core.c:2288
  usb_disable_device+0x211/0x690 drivers/usb/core/message.c:1237
  usb_disconnect+0x284/0x8d0 drivers/usb/core/hub.c:2199
  hub_port_connect drivers/usb/core/hub.c:4949 [inline]
  hub_port_connect_change drivers/usb/core/hub.c:5213 [inline]
  port_event drivers/usb/core/hub.c:5359 [inline]
  hub_event+0x1454/0x3640 drivers/usb/core/hub.c:5441
  process_one_work+0x92b/0x1530 kernel/workqueue.c:2269
  process_scheduled_works kernel/workqueue.c:2331 [inline]
  worker_thread+0x7ab/0xe20 kernel/workqueue.c:2417
  kthread+0x318/0x420 kernel/kthread.c:255
  ret_from_fork+0x24/0x30 arch/x86/entry/entry_64.S:352

Kernel Offset: disabled
Rebooting in 86400 seconds..

Fixes be7fd3c3a8c5e ("media: em28xx: Hauppauge DualHD second tuner functionality)
Reported-by [email protected]
---
 drivers/media/usb/em28xx/em28xx-cards.c | 1 -
 1 file changed, 1 deletion(-)
drivers/media/usb/em28xx/em28xx-cards.c +0 -1
index 1283c7ca9ad51..1de835a591a06 100644
@@ -4020,7 +4020,6 @@ static void em28xx_usb_disconnect(struct usb_interface *intf)
 		dev->dev_next->disconnected = 1;
 		dev_info(&dev->intf->dev, "Disconnecting %s\n",
 			 dev->dev_next->name);
-		flush_request_modules(dev->dev_next);
 	}
 
 	dev->disconnected = 1;
Signature · 1 line
2.20.1
author maintainer
#75 lore raw

PATCH 74/203 arm64/efi: Move variable assignments after SECTIONS

In reply to Sasha Levin

From: Kees Cook <[email protected]>

[ Upstream commit 90776dd1c427cbb4d381aa4b13338f1fb1d20f5e ]

It seems that LLVM's linker does not correctly handle variable assignments involving section positions that are updated during the SECTIONS parsing. Commit aa69fb62bea1 ("arm64/efi: Mark __efistub_stext_offset as an absolute symbol explicitly") ran into this too, but found a different workaround.

However, this was not enough, as other variables were also miscalculated which manifested as boot failures under UEFI where __efistub__end was not taking the correct _end value (they should be the same):

$ ld.lld -EL -maarch64elf --no-undefined -X -shared \
	-Bsymbolic -z notext -z norelro --no-apply-dynamic-relocs \
	-o vmlinux.lld -T poc.lds --whole-archive vmlinux.o && \
  readelf -Ws vmlinux.lld | egrep '\b(__efistub_|)_end\b'
368272: ffff000002218000     0 NOTYPE  LOCAL  HIDDEN    38 __efistub__end
368322: ffff000012318000     0 NOTYPE  GLOBAL DEFAULT   38 _end
$ aarch64-linux-gnu-ld.bfd -EL -maarch64elf --no-undefined -X -shared \
	-Bsymbolic -z notext -z norelro --no-apply-dynamic-relocs \
	-o vmlinux.bfd -T poc.lds --whole-archive vmlinux.o && \
  readelf -Ws vmlinux.bfd | egrep '\b(__efistub_|)_end\b'
338124: ffff000012318000     0 NOTYPE  LOCAL  DEFAULT  ABS __efistub__end
383812: ffff000012318000     0 NOTYPE  GLOBAL DEFAULT 15325 _end

To work around this, all of the __efistub_-prefixed variable assignments need to be moved after the linker script's SECTIONS entry. As it turns out, this also solves the problem fixed in commit aa69fb62bea1, so those changes are reverted here.

---
 arch/arm64/kernel/image-vars.h  | 51 +++++++++++++++++++++++++++++++++
 arch/arm64/kernel/image.h       | 42 ---------------------------
 arch/arm64/kernel/vmlinux.lds.S |  2 ++
 3 files changed, 53 insertions(+), 42 deletions(-)
 create mode 100644 arch/arm64/kernel/image-vars.h
arch/arm64/kernel/image-vars.h new file +51 -0
new file mode 100644
index 0000000000000..25a2a9b479c2f
@@ -0,0 +1,51 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Linker script variables to be set after section resolution, as
+ * ld.lld does not like variables assigned before SECTIONS is processed.
+ */
+#ifndef __ARM64_KERNEL_IMAGE_VARS_H
+#define __ARM64_KERNEL_IMAGE_VARS_H
+
+#ifndef LINKER_SCRIPT
+#error This file should only be included in vmlinux.lds.S
+#endif
+
+#ifdef CONFIG_EFI
+
+__efistub_stext_offset = stext - _text;
+
+/*
+ * The EFI stub has its own symbol namespace prefixed by __efistub_, to
+ * isolate it from the kernel proper. The following symbols are legally
+ * accessed by the stub, so provide some aliases to make them accessible.
+ * Only include data symbols here, or text symbols of functions that are
+ * guaranteed to be safe when executed at another offset than they were
+ * linked at. The routines below are all implemented in assembler in a
+ * position independent manner
+ */
+__efistub_memcmp		= __pi_memcmp;
+__efistub_memchr		= __pi_memchr;
+__efistub_memcpy		= __pi_memcpy;
+__efistub_memmove		= __pi_memmove;
+__efistub_memset		= __pi_memset;
+__efistub_strlen		= __pi_strlen;
+__efistub_strnlen		= __pi_strnlen;
+__efistub_strcmp		= __pi_strcmp;
+__efistub_strncmp		= __pi_strncmp;
+__efistub_strrchr		= __pi_strrchr;
+__efistub___flush_dcache_area	= __pi___flush_dcache_area;
+
+#ifdef CONFIG_KASAN
+__efistub___memcpy		= __pi_memcpy;
+__efistub___memmove		= __pi_memmove;
+__efistub___memset		= __pi_memset;
+#endif
+
+__efistub__text			= _text;
+__efistub__end			= _end;
+__efistub__edata		= _edata;
+__efistub_screen_info		= screen_info;
+
+#endif
+
+#endif /* __ARM64_KERNEL_IMAGE_VARS_H */
arch/arm64/kernel/image.h +0 -42

46 lines not on this page · raw message

arch/arm64/kernel/vmlinux.lds.S +2 -0
index 7fa0083749078..803b24d2464ae 100644
@@ -245,6 +245,8 @@ SECTIONS
 	HEAD_SYMBOLS
 }
 
+#include "image-vars.h"
+
 /*
  * The HYP init code and ID map text can't be longer than a page each,
  * and should not cross a page boundary.
Signature · 1 line
2.20.1
author maintainer
#78 lore raw

PATCH 77/203 dmaengine: iop-adma: use correct printk format strings

In reply to Sasha Levin

From: Arnd Bergmann <[email protected]>

[ Upstream commit 00c9755524fbaa28117be774d7c92fddb5ca02f3 ]

When compile-testing on other architectures, we get lots of warnings about incorrect format strings, like:

drivers/dma/iop-adma.c: In function 'iop_adma_alloc_slots':
drivers/dma/iop-adma.c:307:6: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t {aka long long unsigned int}' [-Wformat=]

drivers/dma/iop-adma.c: In function 'iop_adma_prep_dma_memcpy':

Quoted 1 line
Quoted 1 line

drivers/dma/iop-adma.c:518:40: warning: format '%u' expects argument of type 'unsigned int', but argument 5 has type 'size_t {aka long unsigned int}' [-Wformat=]

Use %zu for printing size_t as required, and cast the dma_addr_t arguments to 'u64' for printing with %llx. Ideally this should use the %pad format string, but that requires an lvalue argument that doesn't work here.

---
 drivers/dma/iop-adma.c | 18 +++++++++---------
 1 file changed, 9 insertions(+), 9 deletions(-)
drivers/dma/iop-adma.c +9 -9
index c6c0143670d9d..a776857d89c8f 100644
@@ -116,9 +116,9 @@ static void __iop_adma_slot_cleanup(struct iop_adma_chan *iop_chan)
 	list_for_each_entry_safe(iter, _iter, &iop_chan->chain,
 					chain_node) {
 		pr_debug("\tcookie: %d slot: %d busy: %d "
-			"this_desc: %#x next_desc: %#x ack: %d\n",
+			"this_desc: %#x next_desc: %#llx ack: %d\n",
 			iter->async_tx.cookie, iter->idx, busy,
-			iter->async_tx.phys, iop_desc_get_next_desc(iter),
+			iter->async_tx.phys, (u64)iop_desc_get_next_desc(iter),
 			async_tx_test_ack(&iter->async_tx));
 		prefetch(_iter);
 		prefetch(&_iter->async_tx);
@@ -306,9 +306,9 @@ iop_adma_alloc_slots(struct iop_adma_chan *iop_chan, int num_slots,
 				int i;
 				dev_dbg(iop_chan->device->common.dev,
 					"allocated slot: %d "
-					"(desc %p phys: %#x) slots_per_op %d\n",
+					"(desc %p phys: %#llx) slots_per_op %d\n",
 					iter->idx, iter->hw_desc,
-					iter->async_tx.phys, slots_per_op);
+					(u64)iter->async_tx.phys, slots_per_op);
 
 				/* pre-ack all but the last descriptor */
 				if (num_slots != slots_per_op)
@@ -516,7 +516,7 @@ iop_adma_prep_dma_memcpy(struct dma_chan *chan, dma_addr_t dma_dest,
 		return NULL;
 	BUG_ON(len > IOP_ADMA_MAX_BYTE_COUNT);
 
-	dev_dbg(iop_chan->device->common.dev, "%s len: %u\n",
+	dev_dbg(iop_chan->device->common.dev, "%s len: %zu\n",
 		__func__, len);
 
 	spin_lock_bh(&iop_chan->lock);
@@ -549,7 +549,7 @@ iop_adma_prep_dma_xor(struct dma_chan *chan, dma_addr_t dma_dest,
 	BUG_ON(len > IOP_ADMA_XOR_MAX_BYTE_COUNT);
 
 	dev_dbg(iop_chan->device->common.dev,
-		"%s src_cnt: %d len: %u flags: %lx\n",
+		"%s src_cnt: %d len: %zu flags: %lx\n",
 		__func__, src_cnt, len, flags);
 
 	spin_lock_bh(&iop_chan->lock);
@@ -582,7 +582,7 @@ iop_adma_prep_dma_xor_val(struct dma_chan *chan, dma_addr_t *dma_src,
 	if (unlikely(!len))
 		return NULL;
 
-	dev_dbg(iop_chan->device->common.dev, "%s src_cnt: %d len: %u\n",
+	dev_dbg(iop_chan->device->common.dev, "%s src_cnt: %d len: %zu\n",
 		__func__, src_cnt, len);
 
 	spin_lock_bh(&iop_chan->lock);
@@ -620,7 +620,7 @@ iop_adma_prep_dma_pq(struct dma_chan *chan, dma_addr_t *dst, dma_addr_t *src,
 	BUG_ON(len > IOP_ADMA_XOR_MAX_BYTE_COUNT);
 
 	dev_dbg(iop_chan->device->common.dev,
-		"%s src_cnt: %d len: %u flags: %lx\n",
+		"%s src_cnt: %d len: %zu flags: %lx\n",
 		__func__, src_cnt, len, flags);
 
 	if (dmaf_p_disabled_continue(flags))
@@ -683,7 +683,7 @@ iop_adma_prep_dma_pq_val(struct dma_chan *chan, dma_addr_t *pq, dma_addr_t *src,
 		return NULL;
 	BUG_ON(len > IOP_ADMA_XOR_MAX_BYTE_COUNT);
 
-	dev_dbg(iop_chan->device->common.dev, "%s src_cnt: %d len: %u\n",
+	dev_dbg(iop_chan->device->common.dev, "%s src_cnt: %d len: %zu\n",
 		__func__, src_cnt, len);
 
 	spin_lock_bh(&iop_chan->lock);
Signature · 1 line
2.20.1
author maintainer
#81 lore raw

PATCH 80/203 perf record: Support aarch64 random socket_id assignment

In reply to Sasha Levin

From: Tan Xiaojun <[email protected]>

[ Upstream commit 0a4d8fb229dd78f9e0752817339e19e903b37a60 ]

Same as in the commit 01766229533f ("perf record: Support s390 random socket_id assignment"), aarch64 also have this problem.

Without this fix:

[root@localhost perf]# ./perf report --header -I -v
...
socket_id number is too big.You may need to upgrade the perf tool.

# ========

  # captured on    : Thu Aug  1 22:58:38 2019
  # header version : 1
  ...
  # Core ID and Socket ID information is not available
  ...

With this fix:
[root@localhost perf]# ./perf report --header -I -v
...
cpumask list: 0-31
cpumask list: 32-63
cpumask list: 64-95
cpumask list: 96-127

# ========

  # captured on    : Thu Aug  1 22:58:38 2019
  # header version : 1
  ...
  # CPU 0: Core ID 0, Socket ID 36
  # CPU 1: Core ID 1, Socket ID 36
  ...
  # CPU 126: Core ID 126, Socket ID 8442
  # CPU 127: Core ID 127, Socket ID 8442
  ...
Cc Alexander Shishkin <[email protected]>
Cc Alexey Budankov <[email protected]>
Cc Kan Liang <[email protected]>
Cc Namhyung Kim <[email protected]>
Cc Peter Zijlstra <[email protected]>
Cc Song Liu <[email protected]>
Cc Steven Rostedt (VMware) <[email protected]>
Cc Tzvetomir Stoyanov (VMware) <[email protected]>
---
 tools/perf/util/header.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
tools/perf/util/header.c +3 -1
index 1903d7ec97976..bf7cf12495539 100644
@@ -2251,8 +2251,10 @@ static int process_cpu_topology(struct feat_fd *ff, void *data __maybe_unused)
 	/* On s390 the socket_id number is not related to the numbers of cpus.
 	 * The socket_id number might be higher than the numbers of cpus.
 	 * This depends on the configuration.
+	 * AArch64 is the same.
 	 */
-	if (ph->env.arch && !strncmp(ph->env.arch, "s390", 4))
+	if (ph->env.arch && (!strncmp(ph->env.arch, "s390", 4)
+			  || !strncmp(ph->env.arch, "aarch64", 7)))
 		do_core_id_test = false;
 
 	for (i = 0; i < (u32)cpu_nr; i++) {
Signature · 1 line
2.20.1
author maintainer
#82 lore raw

PATCH 81/203 ALSA: hda: Add codec on bus address table lately

In reply to Sasha Levin

From: Takashi Iwai <[email protected]>

[ Upstream commit ee5f85d9290fe25d460bd320b7fe073075d72d33 ]

The call of snd_hdac_bus_add_device() is needed only for registering the codec onto the bus caddr_tbl[] that is referred essentially only in the unsol event handler. That is, the reason of this call and the release by the counter-part function snd_hdac_bus_remove_device() is just to assure that the unsol event gets notified to the codec.

But the current implementation of the unsol notification wouldn't work properly when the codec is still in a premature init state. So this patch tries to work around it by delaying the caddr_tbl[] registration at the point of snd_hdac_device_register().

Also, the order of snd_hdac_bus_remove_device() and device_del() calls are shuffled to make sure that the unsol event is masked before deleting the device.

---
 sound/hda/hdac_device.c | 21 ++++++++++++---------
 1 file changed, 12 insertions(+), 9 deletions(-)
sound/hda/hdac_device.c +12 -9
index b26cc93e7e103..033bcef8751a8 100644
@@ -61,10 +61,6 @@ int snd_hdac_device_init(struct hdac_device *codec, struct hdac_bus *bus,
 	pm_runtime_get_noresume(&codec->dev);
 	atomic_set(&codec->in_pm, 0);
 
-	err = snd_hdac_bus_add_device(bus, codec);
-	if (err < 0)
-		goto error;
-
 	/* fill parameters */
 	codec->vendor_id = snd_hdac_read_parm(codec, AC_NODE_ROOT,
 					      AC_PAR_VENDOR_ID);
@@ -143,15 +139,22 @@ int snd_hdac_device_register(struct hdac_device *codec)
 	err = device_add(&codec->dev);
 	if (err < 0)
 		return err;
+	err = snd_hdac_bus_add_device(codec->bus, codec);
+	if (err < 0)
+		goto error;
 	mutex_lock(&codec->widget_lock);
 	err = hda_widget_sysfs_init(codec);
 	mutex_unlock(&codec->widget_lock);
-	if (err < 0) {
-		device_del(&codec->dev);
-		return err;
-	}
+	if (err < 0)
+		goto error_remove;
 
 	return 0;
+
+ error_remove:
+	snd_hdac_bus_remove_device(codec->bus, codec);
+ error:
+	device_del(&codec->dev);
+	return err;
 }
 EXPORT_SYMBOL_GPL(snd_hdac_device_register);
 
@@ -165,8 +168,8 @@ void snd_hdac_device_unregister(struct hdac_device *codec)
 		mutex_lock(&codec->widget_lock);
 		hda_widget_sysfs_exit(codec);
 		mutex_unlock(&codec->widget_lock);
-		device_del(&codec->dev);
 		snd_hdac_bus_remove_device(codec->bus, codec);
+		device_del(&codec->dev);
 	}
 }
 EXPORT_SYMBOL_GPL(snd_hdac_device_unregister);
Signature · 1 line
2.20.1
author maintainer
#83 lore raw

PATCH 82/203 media: vsp1: fix memory leak of dl on error return path

In reply to Sasha Levin

From: Colin Ian King <[email protected]>

[ Upstream commit 70c55c1ad1a76e804ee5330e134674f5d2741cb7 ]

Currently when the call vsp1_dl_body_get fails and returns null the error return path leaks the allocation of dl. Fix this by kfree'ing dl before returning.

Addresses-Coverity: ("Resource leak")

Fixes 5d7936b8e27d ("media: vsp1: Convert display lists to use new body pool")
---
 drivers/media/platform/vsp1/vsp1_dl.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/media/platform/vsp1/vsp1_dl.c +3 -1
index 104b6f5145364..d7b43037e500a 100644
@@ -557,8 +557,10 @@ static struct vsp1_dl_list *vsp1_dl_list_alloc(struct vsp1_dl_manager *dlm)
 
 	/* Get a default body for our list. */
 	dl->body0 = vsp1_dl_body_get(dlm->pool);
-	if (!dl->body0)
+	if (!dl->body0) {
+		kfree(dl);
 		return NULL;
+	}
 
 	header_offset = dl->body0->max_entries * sizeof(*dl->body0->entries);
 
Signature · 1 line
2.20.1
author maintainer
#84 lore raw

PATCH 83/203 media: i2c: ov5645: Fix power sequence

In reply to Sasha Levin

From: Ezequiel Garcia <[email protected]>

[ Upstream commit 092e8eb90a7dc7dd210cd4e2ea36075d0a7f96af ]

This is mostly a port of Jacopo's fix:

commit aa4bb8b8838ffcc776a79f49a4d7476b82405349
Author: Jacopo Mondi <[email protected]>
Date: Fri Jul 6 05:51:52 2018 -0400

media: ov5640: Re-work MIPI startup sequence

In the OV5645 case, the changes are:

- At set_power(1) time power up MIPI Tx/Rx and set data and clock lanes in LP11 during 'sleep' and 'idle' with MIPI clock in non-continuous mode.
- At set_power(0) time power down MIPI Tx/Rx (in addition to the current power down of regulators and clock gating).
- At s_stream time enable/disable the MIPI interface output.

With this commit the sensor is able to enter LP-11 mode during power up, as expected by some CSI-2 controllers.

Many thanks to Fabio Estevam for his help debugging this issue.

---
 drivers/media/i2c/ov5645.c | 26 ++++++++++++++++++--------
 1 file changed, 18 insertions(+), 8 deletions(-)
drivers/media/i2c/ov5645.c +18 -8
index 124c8df046337..58972c884705c 100644
@@ -45,6 +45,8 @@
 #define		OV5645_CHIP_ID_HIGH_BYTE	0x56
 #define OV5645_CHIP_ID_LOW		0x300b
 #define		OV5645_CHIP_ID_LOW_BYTE		0x45
+#define OV5645_IO_MIPI_CTRL00		0x300e
+#define OV5645_PAD_OUTPUT00		0x3019
 #define OV5645_AWB_MANUAL_CONTROL	0x3406
 #define		OV5645_AWB_MANUAL_ENABLE	BIT(0)
 #define OV5645_AEC_PK_MANUAL		0x3503
@@ -55,6 +57,7 @@
 #define		OV5645_ISP_VFLIP		BIT(2)
 #define OV5645_TIMING_TC_REG21		0x3821
 #define		OV5645_SENSOR_MIRROR		BIT(1)
+#define OV5645_MIPI_CTRL00		0x4800
 #define OV5645_PRE_ISP_TEST_SETTING_1	0x503d
 #define		OV5645_TEST_PATTERN_MASK	0x3
 #define		OV5645_SET_TEST_PATTERN(x)	((x) & OV5645_TEST_PATTERN_MASK)
@@ -121,7 +124,6 @@ static const struct reg_value ov5645_global_init_setting[] = {
 	{ 0x3503, 0x07 },
 	{ 0x3002, 0x1c },
 	{ 0x3006, 0xc3 },
-	{ 0x300e, 0x45 },
 	{ 0x3017, 0x00 },
 	{ 0x3018, 0x00 },
 	{ 0x302e, 0x0b },
@@ -350,7 +352,10 @@ static const struct reg_value ov5645_global_init_setting[] = {
 	{ 0x3a1f, 0x14 },
 	{ 0x0601, 0x02 },
 	{ 0x3008, 0x42 },
-	{ 0x3008, 0x02 }
+	{ 0x3008, 0x02 },
+	{ OV5645_IO_MIPI_CTRL00, 0x40 },
+	{ OV5645_MIPI_CTRL00, 0x24 },
+	{ OV5645_PAD_OUTPUT00, 0x70 }
 };
 
 static const struct reg_value ov5645_setting_sxga[] = {
@@ -737,13 +742,9 @@ static int ov5645_s_power(struct v4l2_subdev *sd, int on)
 				goto exit;
 			}
 
-			ret = ov5645_write_reg(ov5645, OV5645_SYSTEM_CTRL0,
-					       OV5645_SYSTEM_CTRL0_STOP);
-			if (ret < 0) {
-				ov5645_set_power_off(ov5645);
-				goto exit;
-			}
+			usleep_range(500, 1000);
 		} else {
+			ov5645_write_reg(ov5645, OV5645_IO_MIPI_CTRL00, 0x58);
 			ov5645_set_power_off(ov5645);
 		}
 	}
@@ -1049,11 +1050,20 @@ static int ov5645_s_stream(struct v4l2_subdev *subdev, int enable)
 			dev_err(ov5645->dev, "could not sync v4l2 controls\n");
 			return ret;
 		}
+
+		ret = ov5645_write_reg(ov5645, OV5645_IO_MIPI_CTRL00, 0x45);
+		if (ret < 0)
+			return ret;
+
 		ret = ov5645_write_reg(ov5645, OV5645_SYSTEM_CTRL0,
 				       OV5645_SYSTEM_CTRL0_START);
 		if (ret < 0)
 			return ret;
 	} else {
+		ret = ov5645_write_reg(ov5645, OV5645_IO_MIPI_CTRL00, 0x40);
+		if (ret < 0)
+			return ret;
+
 		ret = ov5645_write_reg(ov5645, OV5645_SYSTEM_CTRL0,
 				       OV5645_SYSTEM_CTRL0_STOP);
 		if (ret < 0)
Signature · 1 line
2.20.1
author maintainer
#80 lore raw

PATCH 79/203 perf ftrace: Use CAP_SYS_ADMIN instead of euid==0

In reply to Sasha Levin

From: Igor Lubashev <[email protected]>

[ Upstream commit c766f3df635de14295e410c6dd5410bc416c24a0 ]

The kernel requires CAP_SYS_ADMIN instead of euid==0 to mount debugfs for ftrace. Make perf do the same.

---
 tools/perf/builtin-ftrace.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
tools/perf/builtin-ftrace.c +3 -1
index 0193128104056..10971255fd2dc 100644
@@ -13,6 +13,7 @@
 #include <signal.h>
 #include <fcntl.h>
 #include <poll.h>
+#include <linux/capability.h>
 
 #include "debug.h"
 #include <subcmd/parse-options.h>
@@ -21,6 +22,7 @@
 #include "target.h"
 #include "cpumap.h"
 #include "thread_map.h"
+#include "util/cap.h"
 #include "util/config.h"
 
 
@@ -281,7 +283,7 @@ static int __cmd_ftrace(struct perf_ftrace *ftrace, int argc, const char **argv)
 		.events = POLLIN,
 	};
 
-	if (geteuid() != 0) {
+	if (!perf_cap__capable(CAP_SYS_ADMIN)) {
 		pr_err("ftrace only works for root!\n");
 		return -1;
 	}
Signature · 7 lines
2.20.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
author maintainer
#91 lore raw

PATCH 86/203 kasan/arm64: fix CONFIG_KASAN_SW_TAGS && KASAN_INLINE

In reply to Sasha Levin

From: Mark Rutland <[email protected]>

[ Upstream commit 34b5560db40d2941cfbe82eca1641353d5aed1a9 ]

The generic Makefile.kasan propagates CONFIG_KASAN_SHADOW_OFFSET into KASAN_SHADOW_OFFSET, but only does so for CONFIG_KASAN_GENERIC.

Since commit:

6bd1d0be0e97936d ("arm64: kasan: Switch to using KASAN_SHADOW_OFFSET")

... arm64 defines CONFIG_KASAN_SHADOW_OFFSET in Kconfig rather than defining KASAN_SHADOW_OFFSET in a Makefile. Thus, if CONFIG_KASAN_SW_TAGS && KASAN_INLINE are selected, we get build time splats due to KASAN_SHADOW_OFFSET not being set:

| [mark@lakrids:~/src/linux]% usellvm 8.0.1 usekorg 8.1.0  make ARCH=arm64 CROSS_COMPILE=aarch64-linux- CC=clang
| scripts/kconfig/conf  --syncconfig Kconfig
|   CC      scripts/mod/empty.o
| clang (LLVM option parsing): for the -hwasan-mapping-offset option: '' value invalid for uint argument!
| scripts/Makefile.build:273: recipe for target 'scripts/mod/empty.o' failed
| make[1]: *** [scripts/mod/empty.o] Error 1
| Makefile:1123: recipe for target 'prepare0' failed
| make: *** [prepare0] Error 2

Let's fix this by always propagating CONFIG_KASAN_SHADOW_OFFSET into KASAN_SHADOW_OFFSET if CONFIG_KASAN is selected, moving the existing common definition of +CFLAGS_KASAN_NOSANITIZE to the top of Makefile.kasan.

Tested-by Steve Capper <[email protected]>

---
 scripts/Makefile.kasan | 11 +++++------
 1 file changed, 5 insertions(+), 6 deletions(-)
scripts/Makefile.kasan +5 -6
index 6410bd22fe387..03757cc60e06c 100644
@@ -1,4 +1,9 @@
 # SPDX-License-Identifier: GPL-2.0
+ifdef CONFIG_KASAN
+CFLAGS_KASAN_NOSANITIZE := -fno-builtin
+KASAN_SHADOW_OFFSET ?= $(CONFIG_KASAN_SHADOW_OFFSET)
+endif
+
 ifdef CONFIG_KASAN_GENERIC
 
 ifdef CONFIG_KASAN_INLINE
@@ -7,8 +12,6 @@ else
 	call_threshold := 0
 endif
 
-KASAN_SHADOW_OFFSET ?= $(CONFIG_KASAN_SHADOW_OFFSET)
-
 CFLAGS_KASAN_MINIMAL := -fsanitize=kernel-address
 
 cc-param = $(call cc-option, -mllvm -$(1), $(call cc-option, --param $(1)))
@@ -45,7 +48,3 @@ CFLAGS_KASAN := -fsanitize=kernel-hwaddress \
 		$(instrumentation_flags)
 
 endif # CONFIG_KASAN_SW_TAGS
-
-ifdef CONFIG_KASAN
-CFLAGS_KASAN_NOSANITIZE := -fno-builtin
-endif
Signature · 1 line
2.20.1
author maintainer
#90 lore raw

PATCH 85/203 media: imx: mipi csi-2: Don't fail if initial state times-out

In reply to Sasha Levin

From: Ezequiel Garcia <[email protected]>

[ Upstream commit 0d5078c7172c46db6c58718d817b9fcf769554b4 ]

Not all sensors will be able to guarantee a proper initial state. This may be either because the driver is not properly written, or (probably unlikely) because the hardware won't support it.

While the right solution in the former case is to fix the sensor driver, the real world not always allows right solutions, due to lack of available documentation and support on these sensors.

Let's relax this requirement, and allow the driver to support stream start, even if the sensor initial sequence wasn't the expected.

Also improve the warning message to better explain the problem and provide a hint that the sensor driver needs to be fixed.

---
 drivers/staging/media/imx/imx6-mipi-csi2.c | 12 ++++--------
 1 file changed, 4 insertions(+), 8 deletions(-)
drivers/staging/media/imx/imx6-mipi-csi2.c +4 -8
index f29e28df36ed8..bfa4b254c4e48 100644
@@ -243,7 +243,7 @@ static int __maybe_unused csi2_dphy_wait_ulp(struct csi2_dev *csi2)
 }
 
 /* Waits for low-power LP-11 state on data and clock lanes. */
-static int csi2_dphy_wait_stopstate(struct csi2_dev *csi2)
+static void csi2_dphy_wait_stopstate(struct csi2_dev *csi2)
 {
 	u32 mask, reg;
 	int ret;
@@ -254,11 +254,9 @@ static int csi2_dphy_wait_stopstate(struct csi2_dev *csi2)
 	ret = readl_poll_timeout(csi2->base + CSI2_PHY_STATE, reg,
 				 (reg & mask) == mask, 0, 500000);
 	if (ret) {
-		v4l2_err(&csi2->sd, "LP-11 timeout, phy_state = 0x%08x\n", reg);
-		return ret;
+		v4l2_warn(&csi2->sd, "LP-11 wait timeout, likely a sensor driver bug, expect capture failures.\n");
+		v4l2_warn(&csi2->sd, "phy_state = 0x%08x\n", reg);
 	}
-
-	return 0;
 }
 
 /* Wait for active clock on the clock lane. */
@@ -316,9 +314,7 @@ static int csi2_start(struct csi2_dev *csi2)
 	csi2_enable(csi2, true);
 
 	/* Step 5 */
-	ret = csi2_dphy_wait_stopstate(csi2);
-	if (ret)
-		goto err_assert_reset;
+	csi2_dphy_wait_stopstate(csi2);
 
 	/* Step 6 */
 	ret = v4l2_subdev_call(csi2->src_sd, video, s_stream, 1);
Signature · 1 line
2.20.1
author maintainer
#96 lore raw

PATCH 89/203 m68k: Prevent some compiler warnings in Coldfire builds

In reply to Sasha Levin

From: Finn Thain <[email protected]>

[ Upstream commit 94c04390225bcd8283103fd0c04be20cc30cc979 ]

Since commit d3b41b6bb49e ("m68k: Dispatch nvram_ops calls to Atari or Mac functions"), Coldfire builds generate compiler warnings due to the unconditional inclusion of asm/atarihw.h and asm/macintosh.h.

The inclusion of asm/atarihw.h causes warnings like this:

In file included from ./arch/m68k/include/asm/atarihw.h:25:0,

                 from arch/m68k/kernel/setup_mm.c:41,
                 from arch/m68k/kernel/setup.c:3:

./arch/m68k/include/asm/raw_io.h:39:0: warning: "__raw_readb" redefined
#define __raw_readb in_8

In file included from ./arch/m68k/include/asm/io.h:6:0,

                 from arch/m68k/kernel/setup_mm.c:36,
                 from arch/m68k/kernel/setup.c:3:

./arch/m68k/include/asm/io_no.h:16:0: note: this is the location of the previous definition
#define __raw_readb(addr) \
...

This issue is resolved by dropping the asm/raw_io.h include. It turns out that asm/io_mm.h already includes that header file.

Moving the relevant macro definitions helps to clarify this dependency and make it safe to include asm/atarihw.h.

The other warnings look like this:

In file included from arch/m68k/kernel/setup_mm.c:48:0,

                 from arch/m68k/kernel/setup.c:3:
./arch/m68k/include/asm/macintosh.h:19:35: warning: 'struct irq_data' declared inside parameter list will not be visible outside of this definition or declaration
 extern void mac_irq_enable(struct irq_data *data);
                                   ^~~~~~~~

...

This issue is resolved by adding the missing linux/irq.h include.

---
 arch/m68k/include/asm/atarihw.h   | 9 ---------
 arch/m68k/include/asm/io_mm.h     | 6 +++++-
 arch/m68k/include/asm/macintosh.h | 1 +
 3 files changed, 6 insertions(+), 10 deletions(-)
arch/m68k/include/asm/atarihw.h +0 -9
index 533008262b691..5e5601c382b80 100644
@@ -22,7 +22,6 @@
 
 #include <linux/types.h>
 #include <asm/bootinfo-atari.h>
-#include <asm/raw_io.h>
 #include <asm/kmap.h>
 
 extern u_long atari_mch_cookie;
@@ -132,14 +131,6 @@ extern struct atari_hw_present atari_hw_present;
  */
 
 
-#define atari_readb   raw_inb
-#define atari_writeb  raw_outb
-
-#define atari_inb_p   raw_inb
-#define atari_outb_p  raw_outb
-
-
-
 #include <linux/mm.h>
 #include <asm/cacheflush.h>
 
arch/m68k/include/asm/io_mm.h +5 -1
index 6c03ca5bc4365..819f611dccf28 100644
@@ -29,7 +29,11 @@
 #include <asm-generic/iomap.h>
 
 #ifdef CONFIG_ATARI
-#include <asm/atarihw.h>
+#define atari_readb   raw_inb
+#define atari_writeb  raw_outb
+
+#define atari_inb_p   raw_inb
+#define atari_outb_p  raw_outb
 #endif
 
 
arch/m68k/include/asm/macintosh.h +1 -0
index d9a08bed4b128..f653b60f2afcf 100644
@@ -4,6 +4,7 @@
 
 #include <linux/seq_file.h>
 #include <linux/interrupt.h>
+#include <linux/irq.h>
 
 #include <asm/bootinfo-mac.h>
 
Signature · 1 line
2.20.1
author maintainer
#102 lore raw

PATCH 95/203 media: hdpvr: add terminating 0 at end of string

In reply to Sasha Levin

From: Hans Verkuil <[email protected]>

[ Upstream commit 8b8900b729e4f31f12ac1127bde137c775c327e6 ]

dev->usbc_buf was passed as argument for %s, but it was not safeguarded by a terminating 0.

This caused this syzbot issue:

https://syzkaller.appspot.com/bug?extid=79d18aac4bf1770dd050

Reported-and-tested-by [email protected]
---
 drivers/media/usb/hdpvr/hdpvr-core.c | 1 +
 1 file changed, 1 insertion(+)
drivers/media/usb/hdpvr/hdpvr-core.c +1 -0
index a0905c81d2cb2..b75c18a012a73 100644
@@ -137,6 +137,7 @@ static int device_authorization(struct hdpvr_device *dev)
 
 	dev->fw_ver = dev->usbc_buf[1];
 
+	dev->usbc_buf[46] = '\0';
 	v4l2_info(&dev->v4l2_dev, "firmware version 0x%x dated %s\n",
 			  dev->fw_ver, &dev->usbc_buf[2]);
 
Signature · 1 line
2.20.1
author maintainer
#110 lore raw

PATCH 103/203 nbd: add missing config put

In reply to Sasha Levin

From: Mike Christie <[email protected]>

[ Upstream commit 887e975c4172d0d5670c39ead2f18ba1e4ec8133 ]

Fix bug added with the patch:

commit 8f3ea35929a0806ad1397db99a89ffee0140822a

Author: Josef Bacik <[email protected]>
Date:   Mon Jul 16 12:11:35 2018 -0400

nbd: handle unexpected replies better

where if the timeout handler runs when the completion path is and we fail to grab the mutex in the timeout handler we will leave a config reference and cannot free the config later.

---
 drivers/block/nbd.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/block/nbd.c +3 -1
index e21d2ded732b7..a69a90ad92088 100644
@@ -357,8 +357,10 @@ static enum blk_eh_timer_return nbd_xmit_timeout(struct request *req,
 	}
 	config = nbd->config;
 
-	if (!mutex_trylock(&cmd->lock))
+	if (!mutex_trylock(&cmd->lock)) {
+		nbd_config_put(nbd);
 		return BLK_EH_RESET_TIMER;
+	}
 
 	if (config->num_connections > 1) {
 		dev_err_ratelimited(nbd_to_dev(nbd),
Signature · 1 line
2.20.1
author maintainer
#113 lore raw

PATCH 106/203 s390/kasan: provide uninstrumented __strlen

In reply to Sasha Levin

From: Vasily Gorbik <[email protected]>

[ Upstream commit f45f7b5bdaa4828ce871cf03f7c01599a0de57a5 ]

s390 kasan code uses sclp_early_printk to report initialization failures. The code doing that should not be instrumented, because kasan shadow memory has not been set up yet. Even though sclp_early_core.c is compiled with instrumentation disabled it uses strlen function, which is instrumented and would produce shadow memory access if used. To avoid that, introduce uninstrumented __strlen function to be used instead.

Before commit 7e0d92f00246 ("s390/kasan: improve string/memory functions checks") few string functions (including strlen) were escaping kasan instrumentation due to usage of platform specific versions which are implemented in inline assembly.

Fixes 7e0d92f00246 ("s390/kasan: improve string/memory functions checks")
---
 arch/s390/include/asm/string.h | 9 +++++++--
 1 file changed, 7 insertions(+), 2 deletions(-)
arch/s390/include/asm/string.h +7 -2
index 70d87db54e627..4c0690fc5167e 100644
@@ -71,11 +71,16 @@ extern void *__memmove(void *dest, const void *src, size_t n);
 #define memcpy(dst, src, len) __memcpy(dst, src, len)
 #define memmove(dst, src, len) __memmove(dst, src, len)
 #define memset(s, c, n) __memset(s, c, n)
+#define strlen(s) __strlen(s)
+
+#define __no_sanitize_prefix_strfunc(x) __##x
 
 #ifndef __NO_FORTIFY
 #define __NO_FORTIFY /* FORTIFY_SOURCE uses __builtin_memcpy, etc. */
 #endif
 
+#else
+#define __no_sanitize_prefix_strfunc(x) x
 #endif /* defined(CONFIG_KASAN) && !defined(__SANITIZE_ADDRESS__) */
 
 void *__memset16(uint16_t *s, uint16_t v, size_t count);
@@ -163,8 +168,8 @@ static inline char *strcpy(char *dst, const char *src)
 }
 #endif
 
-#ifdef __HAVE_ARCH_STRLEN
-static inline size_t strlen(const char *s)
+#if defined(__HAVE_ARCH_STRLEN) || (defined(CONFIG_KASAN) && !defined(__SANITIZE_ADDRESS__))
+static inline size_t __no_sanitize_prefix_strfunc(strlen)(const char *s)
 {
 	register unsigned long r0 asm("0") = 0;
 	const char *tmp = s;
Signature · 1 line
2.20.1
author maintainer
#108 lore raw

PATCH 101/203 led: triggers: Fix a memory leak bug

In reply to Sasha Levin

From: Wenwen Wang <[email protected]>

[ Upstream commit 60e2dde1e91ae0addb21ac380cc36ebee7534e49 ]

In led_trigger_set(), 'event' is allocated in kasprintf(). However, it is not deallocated in the following execution if the label 'err_activate' or 'err_add_groups' is entered, leading to memory leaks. To fix this issue, free 'event' before returning the error.

Fixes 52c47742f79d ("leds: triggers: send uevent when changing triggers")
---
 drivers/leds/led-triggers.c | 1 +
 1 file changed, 1 insertion(+)
drivers/leds/led-triggers.c +1 -0
index 8d11a5e232271..eff1bda8b5200 100644
@@ -173,6 +173,7 @@ int led_trigger_set(struct led_classdev *led_cdev, struct led_trigger *trig)
 	list_del(&led_cdev->trig_list);
 	write_unlock_irqrestore(&led_cdev->trigger->leddev_list_lock, flags);
 	led_set_brightness(led_cdev, LED_OFF);
+	kfree(event);
 
 	return ret;
 }
Signature · 1 line
2.20.1
author maintainer
#109 lore raw

PATCH 102/203 ASoC: mchp-i2s-mcc: Fix unprepare of GCLK

In reply to Sasha Levin

From: Codrin Ciubotariu <[email protected]>

[ Upstream commit 988b59467b2b14523a266957affbe9eca3e99fc9 ]

If hw_free() gets called after hw_params(), GCLK remains prepared, preventing further use of it. This patch fixes this by unpreparing the clock in hw_free() or if hw_params() gets an error.

Fixes 7e0cdf545a55 ("ASoC: mchp-i2s-mcc: add driver for I2SC Multi-Channel Controller")
---
 sound/soc/atmel/mchp-i2s-mcc.c | 13 +++++++++++--
 1 file changed, 11 insertions(+), 2 deletions(-)
sound/soc/atmel/mchp-i2s-mcc.c +11 -2
index 8272915fa09b9..ab7d5f98e759e 100644
@@ -670,8 +670,13 @@ static int mchp_i2s_mcc_hw_params(struct snd_pcm_substream *substream,
 	}
 
 	ret = regmap_write(dev->regmap, MCHP_I2SMCC_MRA, mra);
-	if (ret < 0)
+	if (ret < 0) {
+		if (dev->gclk_use) {
+			clk_unprepare(dev->gclk);
+			dev->gclk_use = 0;
+		}
 		return ret;
+	}
 	return regmap_write(dev->regmap, MCHP_I2SMCC_MRB, mrb);
 }
 
@@ -710,9 +715,13 @@ static int mchp_i2s_mcc_hw_free(struct snd_pcm_substream *substream,
 		regmap_write(dev->regmap, MCHP_I2SMCC_CR, MCHP_I2SMCC_CR_CKDIS);
 
 		if (dev->gclk_running) {
-			clk_disable_unprepare(dev->gclk);
+			clk_disable(dev->gclk);
 			dev->gclk_running = 0;
 		}
+		if (dev->gclk_use) {
+			clk_unprepare(dev->gclk);
+			dev->gclk_use = 0;
+		}
 	}
 
 	return 0;
Signature · 1 line
2.20.1
author maintainer
#111 lore raw

PATCH 104/203 ACPI / APEI: Release resources if gen_pool_add() fails

In reply to Sasha Levin

From: Liguang Zhang <[email protected]>

[ Upstream commit 6abc7622271dc520f241462e2474c71723638851 ]

Destroy ghes_estatus_pool and release memory allocated via vmalloc() on errors in ghes_estatus_pool_init() in order to avoid memory leaks.

[ bp: do the labels properly and with descriptive names and massage. ]

---
 drivers/acpi/apei/ghes.c | 17 +++++++++++++++--
 1 file changed, 15 insertions(+), 2 deletions(-)
drivers/acpi/apei/ghes.c +15 -2
index a66e00fe31fec..66205ec545553 100644
@@ -153,6 +153,7 @@ static void ghes_unmap(void __iomem *vaddr, enum fixed_addresses fixmap_idx)
 int ghes_estatus_pool_init(int num_ghes)
 {
 	unsigned long addr, len;
+	int rc;
 
 	ghes_estatus_pool = gen_pool_create(GHES_ESTATUS_POOL_MIN_ALLOC_ORDER, -1);
 	if (!ghes_estatus_pool)
@@ -164,7 +165,7 @@ int ghes_estatus_pool_init(int num_ghes)
 	ghes_estatus_pool_size_request = PAGE_ALIGN(len);
 	addr = (unsigned long)vmalloc(PAGE_ALIGN(len));
 	if (!addr)
-		return -ENOMEM;
+		goto err_pool_alloc;
 
 	/*
 	 * New allocation must be visible in all pgd before it can be found by
@@ -172,7 +173,19 @@ int ghes_estatus_pool_init(int num_ghes)
 	 */
 	vmalloc_sync_all();
 
-	return gen_pool_add(ghes_estatus_pool, addr, PAGE_ALIGN(len), -1);
+	rc = gen_pool_add(ghes_estatus_pool, addr, PAGE_ALIGN(len), -1);
+	if (rc)
+		goto err_pool_add;
+
+	return 0;
+
+err_pool_add:
+	vfree((void *)addr);
+
+err_pool_alloc:
+	gen_pool_destroy(ghes_estatus_pool);
+
+	return -ENOMEM;
 }
 
 static int map_gen_v2(struct ghes *ghes)
Signature · 1 line
2.20.1
author maintainer
#105 lore raw

PATCH 98/203 tools headers: Fixup bitsperlong per arch includes

In reply to Sasha Levin

From: Arnaldo Carvalho de Melo <[email protected]>

[ Upstream commit 42fc2e9ef9603a7948aaa4ffd8dfb94b30294ad8 ]

We were getting the file by luck, from one of the paths in -I, fix it to get it from the proper place:

  $ cd tools/include/uapi/asm/
  [acme@quaco asm]$ grep include bitsperlong.h
  #include "../../arch/x86/include/uapi/asm/bitsperlong.h"
  #include "../../arch/arm64/include/uapi/asm/bitsperlong.h"
  #include "../../arch/powerpc/include/uapi/asm/bitsperlong.h"
  #include "../../arch/s390/include/uapi/asm/bitsperlong.h"
  #include "../../arch/sparc/include/uapi/asm/bitsperlong.h"
  #include "../../arch/mips/include/uapi/asm/bitsperlong.h"
  #include "../../arch/ia64/include/uapi/asm/bitsperlong.h"
  #include "../../arch/riscv/include/uapi/asm/bitsperlong.h"
  #include "../../arch/alpha/include/uapi/asm/bitsperlong.h"
  #include <asm-generic/bitsperlong.h>
  $ ls -la ../../arch/x86/include/uapi/asm/bitsperlong.h
  ls: cannot access '../../arch/x86/include/uapi/asm/bitsperlong.h': No such file or directory
  $ ls -la ../../../arch/*/include/uapi/asm/bitsperlong.h
  -rw-rw-r--. 1 237 ../../../arch/alpha/include/uapi/asm/bitsperlong.h
  -rw-rw-r--. 1 841 ../../../arch/arm64/include/uapi/asm/bitsperlong.h
  -rw-rw-r--. 1 966 ../../../arch/hexagon/include/uapi/asm/bitsperlong.h
  -rw-rw-r--. 1 234 ../../../arch/ia64/include/uapi/asm/bitsperlong.h
  -rw-rw-r--. 1 100 ../../../arch/microblaze/include/uapi/asm/bitsperlong.h
  -rw-rw-r--. 1 244 ../../../arch/mips/include/uapi/asm/bitsperlong.h
  -rw-rw-r--. 1 352 ../../../arch/parisc/include/uapi/asm/bitsperlong.h
  -rw-rw-r--. 1 312 ../../../arch/powerpc/include/uapi/asm/bitsperlong.h
  -rw-rw-r--. 1 353 ../../../arch/riscv/include/uapi/asm/bitsperlong.h
  -rw-rw-r--. 1 292 ../../../arch/s390/include/uapi/asm/bitsperlong.h
  -rw-rw-r--. 1 323 ../../../arch/sparc/include/uapi/asm/bitsperlong.h
  -rw-rw-r--. 1 320 ../../../arch/x86/include/uapi/asm/bitsperlong.h
  $

Found while fixing some other problem, before it was escaping the tools/ chroot and using stuff in the kernel sources:

CC /tmp/build/perf/util/find_bit.o
In file included from /git/linux/tools/include/../../arch/x86/include/uapi/asm/bitsperlong.h:11,

                 from /git/linux/tools/include/uapi/asm/bitsperlong.h:3,
                 from /git/linux/tools/include/linux/bits.h:6,
                 from /git/linux/tools/include/linux/bitops.h:13,
                 from ../lib/find_bit.c:17:
  # cd /git/linux/tools/include/../../arch/x86/include/uapi/asm/
  # pwd
  /git/linux/arch/x86/include/uapi/asm
  #

Now it is getting the one we want it to, i.e. the one inside tools/:

CC /tmp/build/perf/util/find_bit.o
In file included from /git/linux/tools/arch/x86/include/uapi/asm/bitsperlong.h:11,
from /git/linux/tools/include/linux/bits.h:6,
from /git/linux/tools/include/linux/bitops.h:13,

---
 tools/include/uapi/asm/bitsperlong.h | 18 +++++++++---------
 1 file changed, 9 insertions(+), 9 deletions(-)
tools/include/uapi/asm/bitsperlong.h +9 -9
index 57aaeaf8e1920..edba4d93e9e6a 100644
@@ -1,22 +1,22 @@
 /* SPDX-License-Identifier: GPL-2.0 */
 #if defined(__i386__) || defined(__x86_64__)
-#include "../../arch/x86/include/uapi/asm/bitsperlong.h"
+#include "../../../arch/x86/include/uapi/asm/bitsperlong.h"
 #elif defined(__aarch64__)
-#include "../../arch/arm64/include/uapi/asm/bitsperlong.h"
+#include "../../../arch/arm64/include/uapi/asm/bitsperlong.h"
 #elif defined(__powerpc__)
-#include "../../arch/powerpc/include/uapi/asm/bitsperlong.h"
+#include "../../../arch/powerpc/include/uapi/asm/bitsperlong.h"
 #elif defined(__s390__)
-#include "../../arch/s390/include/uapi/asm/bitsperlong.h"
+#include "../../../arch/s390/include/uapi/asm/bitsperlong.h"
 #elif defined(__sparc__)
-#include "../../arch/sparc/include/uapi/asm/bitsperlong.h"
+#include "../../../arch/sparc/include/uapi/asm/bitsperlong.h"
 #elif defined(__mips__)
-#include "../../arch/mips/include/uapi/asm/bitsperlong.h"
+#include "../../../arch/mips/include/uapi/asm/bitsperlong.h"
 #elif defined(__ia64__)
-#include "../../arch/ia64/include/uapi/asm/bitsperlong.h"
+#include "../../../arch/ia64/include/uapi/asm/bitsperlong.h"
 #elif defined(__riscv)
-#include "../../arch/riscv/include/uapi/asm/bitsperlong.h"
+#include "../../../arch/riscv/include/uapi/asm/bitsperlong.h"
 #elif defined(__alpha__)
-#include "../../arch/alpha/include/uapi/asm/bitsperlong.h"
+#include "../../../arch/alpha/include/uapi/asm/bitsperlong.h"
 #else
 #include <asm-generic/bitsperlong.h>
 #endif
Signature · 7 lines
2.20.1


_______________________________________________
linux-riscv mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-riscv
author maintainer
#118 lore raw

PATCH 111/203 EDAC/amd64: Support more than two controllers for chip selects handling

In reply to Sasha Levin

From: Yazen Ghannam <[email protected]>

[ Upstream commit d971e28e2ce4696fcc32998c8aced5e47701fffe ]

The struct chip_select array that's used for saving chip select bases and masks is fixed at length of two. There should be one struct chip_select for each controller, so this array should be increased to support systems that may have more than two controllers.

Increase the size of the struct chip_select array to eight, which is the largest number of controllers per die currently supported on AMD systems.

Fix number of DIMMs and Chip Select bases/masks on Family17h, because AMD Family 17h systems support 2 DIMMs, 4 CS bases, and 2 CS masks per channel.

Also, carve out the Family 17h+ reading of the bases/masks into a separate function. This effectively reverts the original bases/masks reading code to before Family 17h support was added.

---
 drivers/edac/amd64_edac.c | 123 +++++++++++++++++++++-----------------
 drivers/edac/amd64_edac.h |   5 +-
 2 files changed, 71 insertions(+), 57 deletions(-)
drivers/edac/amd64_edac.c +68 -55
index 873437be86d9c..dd60cf5a3d969 100644
@@ -810,7 +810,7 @@ static void debug_display_dimm_sizes_df(struct amd64_pvt *pvt, u8 ctrl)
 
 	edac_printk(KERN_DEBUG, EDAC_MC, "UMC%d chip selects:\n", ctrl);
 
-	for (dimm = 0; dimm < 4; dimm++) {
+	for (dimm = 0; dimm < 2; dimm++) {
 		size0 = 0;
 		cs0 = dimm * 2;
 
@@ -942,89 +942,102 @@ static void prep_chip_selects(struct amd64_pvt *pvt)
 	} else if (pvt->fam == 0x15 && pvt->model == 0x30) {
 		pvt->csels[0].b_cnt = pvt->csels[1].b_cnt = 4;
 		pvt->csels[0].m_cnt = pvt->csels[1].m_cnt = 2;
+	} else if (pvt->fam >= 0x17) {
+		int umc;
+
+		for_each_umc(umc) {
+			pvt->csels[umc].b_cnt = 4;
+			pvt->csels[umc].m_cnt = 2;
+		}
+
 	} else {
 		pvt->csels[0].b_cnt = pvt->csels[1].b_cnt = 8;
 		pvt->csels[0].m_cnt = pvt->csels[1].m_cnt = 4;
 	}
 }
 
+static void read_umc_base_mask(struct amd64_pvt *pvt)
+{
+	u32 umc_base_reg, umc_mask_reg;
+	u32 base_reg, mask_reg;
+	u32 *base, *mask;
+	int cs, umc;
+
+	for_each_umc(umc) {
+		umc_base_reg = get_umc_base(umc) + UMCCH_BASE_ADDR;
+
+		for_each_chip_select(cs, umc, pvt) {
+			base = &pvt->csels[umc].csbases[cs];
+
+			base_reg = umc_base_reg + (cs * 4);
+
+			if (!amd_smn_read(pvt->mc_node_id, base_reg, base))
+				edac_dbg(0, "  DCSB%d[%d]=0x%08x reg: 0x%x\n",
+					 umc, cs, *base, base_reg);
+		}
+
+		umc_mask_reg = get_umc_base(umc) + UMCCH_ADDR_MASK;
+
+		for_each_chip_select_mask(cs, umc, pvt) {
+			mask = &pvt->csels[umc].csmasks[cs];
+
+			mask_reg = umc_mask_reg + (cs * 4);
+
+			if (!amd_smn_read(pvt->mc_node_id, mask_reg, mask))
+				edac_dbg(0, "  DCSM%d[%d]=0x%08x reg: 0x%x\n",
+					 umc, cs, *mask, mask_reg);
+		}
+	}
+}
+
 /*
  * Function 2 Offset F10_DCSB0; read in the DCS Base and DCS Mask registers
  */
 static void read_dct_base_mask(struct amd64_pvt *pvt)
 {
-	int base_reg0, base_reg1, mask_reg0, mask_reg1, cs;
+	int cs;
 
 	prep_chip_selects(pvt);
 
-	if (pvt->umc) {
-		base_reg0 = get_umc_base(0) + UMCCH_BASE_ADDR;
-		base_reg1 = get_umc_base(1) + UMCCH_BASE_ADDR;
-		mask_reg0 = get_umc_base(0) + UMCCH_ADDR_MASK;
-		mask_reg1 = get_umc_base(1) + UMCCH_ADDR_MASK;
-	} else {
-		base_reg0 = DCSB0;
-		base_reg1 = DCSB1;
-		mask_reg0 = DCSM0;
-		mask_reg1 = DCSM1;
-	}
+	if (pvt->umc)
+		return read_umc_base_mask(pvt);
 
 	for_each_chip_select(cs, 0, pvt) {
-		int reg0   = base_reg0 + (cs * 4);
-		int reg1   = base_reg1 + (cs * 4);
+		int reg0   = DCSB0 + (cs * 4);
+		int reg1   = DCSB1 + (cs * 4);
 		u32 *base0 = &pvt->csels[0].csbases[cs];
 		u32 *base1 = &pvt->csels[1].csbases[cs];
 
-		if (pvt->umc) {
-			if (!amd_smn_read(pvt->mc_node_id, reg0, base0))
-				edac_dbg(0, "  DCSB0[%d]=0x%08x reg: 0x%x\n",
-					 cs, *base0, reg0);
-
-			if (!amd_smn_read(pvt->mc_node_id, reg1, base1))
-				edac_dbg(0, "  DCSB1[%d]=0x%08x reg: 0x%x\n",
-					 cs, *base1, reg1);
-		} else {
-			if (!amd64_read_dct_pci_cfg(pvt, 0, reg0, base0))
-				edac_dbg(0, "  DCSB0[%d]=0x%08x reg: F2x%x\n",
-					 cs, *base0, reg0);
+		if (!amd64_read_dct_pci_cfg(pvt, 0, reg0, base0))
+			edac_dbg(0, "  DCSB0[%d]=0x%08x reg: F2x%x\n",
+				 cs, *base0, reg0);
 
-			if (pvt->fam == 0xf)
-				continue;
+		if (pvt->fam == 0xf)
+			continue;
 
-			if (!amd64_read_dct_pci_cfg(pvt, 1, reg0, base1))
-				edac_dbg(0, "  DCSB1[%d]=0x%08x reg: F2x%x\n",
-					 cs, *base1, (pvt->fam == 0x10) ? reg1
-								: reg0);
-		}
+		if (!amd64_read_dct_pci_cfg(pvt, 1, reg0, base1))
+			edac_dbg(0, "  DCSB1[%d]=0x%08x reg: F2x%x\n",
+				 cs, *base1, (pvt->fam == 0x10) ? reg1
+							: reg0);
 	}
 
 	for_each_chip_select_mask(cs, 0, pvt) {
-		int reg0   = mask_reg0 + (cs * 4);
-		int reg1   = mask_reg1 + (cs * 4);
+		int reg0   = DCSM0 + (cs * 4);
+		int reg1   = DCSM1 + (cs * 4);
 		u32 *mask0 = &pvt->csels[0].csmasks[cs];
 		u32 *mask1 = &pvt->csels[1].csmasks[cs];
 
-		if (pvt->umc) {
-			if (!amd_smn_read(pvt->mc_node_id, reg0, mask0))
-				edac_dbg(0, "    DCSM0[%d]=0x%08x reg: 0x%x\n",
-					 cs, *mask0, reg0);
-
-			if (!amd_smn_read(pvt->mc_node_id, reg1, mask1))
-				edac_dbg(0, "    DCSM1[%d]=0x%08x reg: 0x%x\n",
-					 cs, *mask1, reg1);
-		} else {
-			if (!amd64_read_dct_pci_cfg(pvt, 0, reg0, mask0))
-				edac_dbg(0, "    DCSM0[%d]=0x%08x reg: F2x%x\n",
-					 cs, *mask0, reg0);
+		if (!amd64_read_dct_pci_cfg(pvt, 0, reg0, mask0))
+			edac_dbg(0, "    DCSM0[%d]=0x%08x reg: F2x%x\n",
+				 cs, *mask0, reg0);
 
-			if (pvt->fam == 0xf)
-				continue;
+		if (pvt->fam == 0xf)
+			continue;
 
-			if (!amd64_read_dct_pci_cfg(pvt, 1, reg0, mask1))
-				edac_dbg(0, "    DCSM1[%d]=0x%08x reg: F2x%x\n",
-					 cs, *mask1, (pvt->fam == 0x10) ? reg1
-								: reg0);
-		}
+		if (!amd64_read_dct_pci_cfg(pvt, 1, reg0, mask1))
+			edac_dbg(0, "    DCSM1[%d]=0x%08x reg: F2x%x\n",
+				 cs, *mask1, (pvt->fam == 0x10) ? reg1
+							: reg0);
 	}
 }
 
drivers/edac/amd64_edac.h +3 -2
index 8f66472f7adc2..4dce6a2ac75f9 100644
@@ -96,6 +96,7 @@
 /* Hardware limit on ChipSelect rows per MC and processors per system */
 #define NUM_CHIPSELECTS			8
 #define DRAM_RANGES			8
+#define NUM_CONTROLLERS			8
 
 #define ON true
 #define OFF false
@@ -351,8 +352,8 @@ struct amd64_pvt {
 	u32 dbam0;		/* DRAM Base Address Mapping reg for DCT0 */
 	u32 dbam1;		/* DRAM Base Address Mapping reg for DCT1 */
 
-	/* one for each DCT */
-	struct chip_select csels[2];
+	/* one for each DCT/UMC */
+	struct chip_select csels[NUM_CONTROLLERS];
 
 	/* DRAM base and limit pairs F1x[78,70,68,60,58,50,48,40] */
 	struct dram_range ranges[DRAM_RANGES];
Signature · 1 line
2.20.1
author maintainer
#119 lore raw

PATCH 112/203 cpufreq: imx-cpufreq-dt: Add i.MX8MN support

In reply to Sasha Levin

From: Anson Huang <[email protected]>

[ Upstream commit 75c000c4bcbe2b0eb82baf90c7dd75c7380cc3fd ]

i.MX8MN has different speed grading definition as below, it has 4 bits to define speed grading, add support for it.

SPEED_GRADE[3:0] MHz

    0000            2300
    0001            2200
    0010            2100
    0011            2000
    0100            1900
    0101            1800
    0110            1700
    0111            1600
    1000            1500
    1001            1400
    1010            1300
    1011            1200
    1100            1100
    1101            1000
    1110             900
    1111             800
---
 drivers/cpufreq/imx-cpufreq-dt.c | 8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)
drivers/cpufreq/imx-cpufreq-dt.c +7 -1
index 4f85f3112784f..35db14cf31026 100644
@@ -16,6 +16,7 @@
 
 #define OCOTP_CFG3_SPEED_GRADE_SHIFT	8
 #define OCOTP_CFG3_SPEED_GRADE_MASK	(0x3 << 8)
+#define IMX8MN_OCOTP_CFG3_SPEED_GRADE_MASK	(0xf << 8)
 #define OCOTP_CFG3_MKT_SEGMENT_SHIFT    6
 #define OCOTP_CFG3_MKT_SEGMENT_MASK     (0x3 << 6)
 
@@ -34,7 +35,12 @@ static int imx_cpufreq_dt_probe(struct platform_device *pdev)
 	if (ret)
 		return ret;
 
-	speed_grade = (cell_value & OCOTP_CFG3_SPEED_GRADE_MASK) >> OCOTP_CFG3_SPEED_GRADE_SHIFT;
+	if (of_machine_is_compatible("fsl,imx8mn"))
+		speed_grade = (cell_value & IMX8MN_OCOTP_CFG3_SPEED_GRADE_MASK)
+			      >> OCOTP_CFG3_SPEED_GRADE_SHIFT;
+	else
+		speed_grade = (cell_value & OCOTP_CFG3_SPEED_GRADE_MASK)
+			      >> OCOTP_CFG3_SPEED_GRADE_SHIFT;
 	mkt_segment = (cell_value & OCOTP_CFG3_MKT_SEGMENT_MASK) >> OCOTP_CFG3_MKT_SEGMENT_SHIFT;
 
 	/*
Signature · 1 line
2.20.1
author maintainer
#120 lore raw

PATCH 113/203 libperf: Fix alignment trap with xyarray contents in 'perf stat'

In reply to Sasha Levin

From: Gerald BAEZA <[email protected]>

[ Upstream commit d9c5c083416500e95da098c01be092b937def7fa ]

Following the patch 'perf stat: Fix --no-scale', an alignment trap happens in process_counter_values() on ARMv7 platforms due to the attempt to copy non 64 bits aligned double words (pointed by 'count') via a NEON vectored instruction ('vld1' with 64 bits alignment constraint).

This patch sets a 64 bits alignment constraint on 'contents[]' field in 'struct xyarray' since the 'count' pointer used above points to such a structure.

---
 tools/perf/util/xyarray.h | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
tools/perf/util/xyarray.h +2 -1
index 7ffe562e7ae7f..2627b038b6f2a 100644
@@ -2,6 +2,7 @@
 #ifndef _PERF_XYARRAY_H_
 #define _PERF_XYARRAY_H_ 1
 
+#include <linux/compiler.h>
 #include <sys/types.h>
 
 struct xyarray {
@@ -10,7 +11,7 @@ struct xyarray {
 	size_t entries;
 	size_t max_x;
 	size_t max_y;
-	char contents[];
+	char contents[] __aligned(8);
 };
 
 struct xyarray *xyarray__new(int xlen, int ylen, size_t entry_size);
Signature · 1 line
2.20.1
author maintainer
#130 lore raw

PATCH 123/203 media: cec-notifier: clear cec_adap in cec_notifier_unregister

In reply to Sasha Levin

From: Hans Verkuil <[email protected]>

[ Upstream commit 14d5511691e5290103bc480998bc322e68f139d4 ]

If cec_notifier_cec_adap_unregister() is called before cec_unregister_adapter() then everything is OK (and this is the case today). But if it is the other way around, then cec_notifier_unregister() is called first, and that doesn't set n->cec_adap to NULL.

So if e.g. cec_notifier_set_phys_addr() is called after cec_notifier_unregister() but before cec_unregister_adapter() then n->cec_adap points to an unregistered and likely deleted cec adapter. So just set n->cec_adap->notifier and n->cec_adap to NULL for rubustness.

Eventually cec_notifier_unregister will disappear and this will be simplified substantially.

---
 drivers/media/cec/cec-notifier.c | 2 ++
 1 file changed, 2 insertions(+)
drivers/media/cec/cec-notifier.c +2 -0
index 52a867bde15fd..4d82a5522072e 100644
@@ -218,6 +218,8 @@ void cec_notifier_unregister(struct cec_notifier *n)
 
 	mutex_lock(&n->lock);
 	n->callback = NULL;
+	n->cec_adap->notifier = NULL;
+	n->cec_adap = NULL;
 	mutex_unlock(&n->lock);
 	cec_notifier_put(n);
 }
Signature · 1 line
2.20.1
author maintainer
#131 lore raw

PATCH 124/203 media: saa7146: add cleanup in hexium_attach()

In reply to Sasha Levin

From: Wenwen Wang <[email protected]>

[ Upstream commit 42e64117d3b4a759013f77bbcf25ab6700e55de7 ]

If saa7146_register_device() fails, no cleanup is executed, leading to memory/resource leaks. To fix this issue, perform necessary cleanup work before returning the error.

---
 drivers/media/pci/saa7146/hexium_gemini.c | 3 +++
 1 file changed, 3 insertions(+)
drivers/media/pci/saa7146/hexium_gemini.c +3 -0
index dca20a3d98e25..f962269306707 100644
@@ -292,6 +292,9 @@ static int hexium_attach(struct saa7146_dev *dev, struct saa7146_pci_extension_d
 	ret = saa7146_register_device(&hexium->video_dev, dev, "hexium gemini", VFL_TYPE_GRABBER);
 	if (ret < 0) {
 		pr_err("cannot register capture v4l2 device. skipping.\n");
+		saa7146_vv_release(dev);
+		i2c_del_adapter(&hexium->i2c_adapter);
+		kfree(hexium);
 		return ret;
 	}
 
Signature · 1 line
2.20.1
author maintainer
#135 lore raw

PATCH 128/203 perf report: Fix --ns time sort key output

In reply to Sasha Levin

From: Andi Kleen <[email protected]>

[ Upstream commit 3dab6ac080dcd7f71cb9ceb84ad7dafecd6f7c07 ]

If the user specified --ns, the column to print the sort time stamp wasn't wide enough to actually print the full nanoseconds.

Widen the time key column width when --ns is specified.

Before:

  % perf record -a sleep 1
  % perf report --sort time,overhead,symbol --stdio --ns
  ...
       2.39%  187851.10000  [k] smp_call_function_single   -      -
       1.53%  187851.10000  [k] intel_idle                 -      -
       0.59%  187851.10000  [.] __wcscmp_ifunc             -      -
       0.33%  187851.10000  [.] 0000000000000000           -      -
       0.28%  187851.10000  [k] cpuidle_enter_state        -      -

After:

  % perf report --sort time,overhead,symbol --stdio --ns
  ...
       2.39%  187851.100000000  [k] smp_call_function_single   -      -
       1.53%  187851.100000000  [k] intel_idle                 -      -
       0.59%  187851.100000000  [.] __wcscmp_ifunc             -      -
       0.33%  187851.100000000  [.] 0000000000000000           -      -
       0.28%  187851.100000000  [k] cpuidle_enter_state        -      -
---
 tools/perf/util/hist.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)
tools/perf/util/hist.c +4 -1
index f24fd1954f6c9..6bd270a1e93e0 100644
@@ -193,7 +193,10 @@ void hists__calc_col_len(struct hists *hists, struct hist_entry *h)
 	hists__new_col_len(hists, HISTC_MEM_LVL, 21 + 3);
 	hists__new_col_len(hists, HISTC_LOCAL_WEIGHT, 12);
 	hists__new_col_len(hists, HISTC_GLOBAL_WEIGHT, 12);
-	hists__new_col_len(hists, HISTC_TIME, 12);
+	if (symbol_conf.nanosecs)
+		hists__new_col_len(hists, HISTC_TIME, 16);
+	else
+		hists__new_col_len(hists, HISTC_TIME, 12);
 
 	if (h->srcline) {
 		len = MAX(strlen(h->srcline), strlen(sort_srcline.se_header));
Signature · 1 line
2.20.1
author maintainer
#137 lore raw

PATCH 130/203 media: aspeed-video: address a protential usage of an unitialized var

In reply to Sasha Levin

From: Mauro Carvalho Chehab <[email protected]>

[ Upstream commit 31b8b0bd6e55c3ea5a08bb8141fa5d3c90600e3b ]

While this might not occur in practice, if the device is doing the right thing, it would be teoretically be possible to have both hsync_counter and vsync_counter negatives.

If this ever happen, ctrl will be undefined, but the driver will still call:

	aspeed_video_update(video, VE_CTRL, 0, ctrl);

Change the code to prevent this to happen.

This was warned by cppcheck:

[drivers/media/platform/aspeed-video.c:653]: (error) Uninitialized variable: ctrl

---
 drivers/media/platform/aspeed-video.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)
drivers/media/platform/aspeed-video.c +3 -2
index f899ac3b4a613..4ef37cfc84467 100644
@@ -630,7 +630,7 @@ static void aspeed_video_check_and_set_polarity(struct aspeed_video *video)
 	}
 
 	if (hsync_counter < 0 || vsync_counter < 0) {
-		u32 ctrl;
+		u32 ctrl = 0;
 
 		if (hsync_counter < 0) {
 			ctrl = VE_CTRL_HSYNC_POL;
@@ -650,7 +650,8 @@ static void aspeed_video_check_and_set_polarity(struct aspeed_video *video)
 				V4L2_DV_VSYNC_POS_POL;
 		}
 
-		aspeed_video_update(video, VE_CTRL, 0, ctrl);
+		if (ctrl)
+			aspeed_video_update(video, VE_CTRL, 0, ctrl);
 	}
 }
 
Signature · 1 line
2.20.1
author maintainer
#139 lore raw

PATCH 132/203 leds: lm3532: Fixes for the driver for stability

In reply to Sasha Levin

From: Dan Murphy <[email protected]>

[ Upstream commit 6559ac32998248182572e1ccae79dc2eb40ac7c6 ]

Fixed misspelled words, added error check during probe on the init of the registers, and fixed ALS/I2C control mode.

Fixes bc1b8492c764 ("leds: lm3532: Introduce the lm3532 LED driver")
---
 drivers/leds/leds-lm3532.c | 17 +++++++++++++----
 1 file changed, 13 insertions(+), 4 deletions(-)
drivers/leds/leds-lm3532.c +13 -4
index 180895b83b888..e55a64847fe2f 100644
@@ -40,7 +40,7 @@
 #define LM3532_REG_ZN_3_LO	0x67
 #define LM3532_REG_MAX		0x7e
 
-/* Contorl Enable */
+/* Control Enable */
 #define LM3532_CTRL_A_ENABLE	BIT(0)
 #define LM3532_CTRL_B_ENABLE	BIT(1)
 #define LM3532_CTRL_C_ENABLE	BIT(2)
@@ -302,7 +302,7 @@ static int lm3532_led_disable(struct lm3532_led *led_data)
 	int ret;
 
 	ret = regmap_update_bits(led_data->priv->regmap, LM3532_REG_ENABLE,
-					 ctrl_en_val, ~ctrl_en_val);
+					 ctrl_en_val, 0);
 	if (ret) {
 		dev_err(led_data->priv->dev, "Failed to set ctrl:%d\n", ret);
 		return ret;
@@ -321,7 +321,7 @@ static int lm3532_brightness_set(struct led_classdev *led_cdev,
 
 	mutex_lock(&led->priv->lock);
 
-	if (led->mode == LM3532_BL_MODE_ALS) {
+	if (led->mode == LM3532_ALS_CTRL) {
 		if (brt_val > LED_OFF)
 			ret = lm3532_led_enable(led);
 		else
@@ -542,11 +542,14 @@ static int lm3532_parse_node(struct lm3532_data *priv)
 		}
 
 		if (led->mode == LM3532_BL_MODE_ALS) {
+			led->mode = LM3532_ALS_CTRL;
 			ret = lm3532_parse_als(priv);
 			if (ret)
 				dev_err(&priv->client->dev, "Failed to parse als\n");
 			else
 				lm3532_als_configure(priv, led);
+		} else {
+			led->mode = LM3532_I2C_CTRL;
 		}
 
 		led->num_leds = fwnode_property_read_u32_array(child,
@@ -590,7 +593,13 @@ static int lm3532_parse_node(struct lm3532_data *priv)
 			goto child_out;
 		}
 
-		lm3532_init_registers(led);
+		ret = lm3532_init_registers(led);
+		if (ret) {
+			dev_err(&priv->client->dev, "register init err: %d\n",
+				ret);
+			fwnode_handle_put(child);
+			goto child_out;
+		}
 
 		i++;
 	}
Signature · 1 line
2.20.1
author maintainer
#142 lore raw

PATCH 135/203 sched/cpufreq: Align trace event behavior of fast switching

In reply to Sasha Levin

From: Douglas RAILLARD <[email protected]>

[ Upstream commit 77c84dd1881d0f0176cb678d770bfbda26c54390 ]

Fast switching path only emits an event for the CPU of interest, whereas the regular path emits an event for all the CPUs that had their frequency changed, i.e. all the CPUs sharing the same policy.

With the current behavior, looking at cpu_frequency event for a given CPU that is using the fast switching path will not give the correct frequency signal.

---
 kernel/sched/cpufreq_schedutil.c | 7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)
kernel/sched/cpufreq_schedutil.c +6 -1
index 867b4bb6d4beb..b03ca2f73713d 100644
@@ -117,6 +117,7 @@ static void sugov_fast_switch(struct sugov_policy *sg_policy, u64 time,
 			      unsigned int next_freq)
 {
 	struct cpufreq_policy *policy = sg_policy->policy;
+	int cpu;
 
 	if (!sugov_update_next_freq(sg_policy, time, next_freq))
 		return;
@@ -126,7 +127,11 @@ static void sugov_fast_switch(struct sugov_policy *sg_policy, u64 time,
 		return;
 
 	policy->cur = next_freq;
-	trace_cpu_frequency(next_freq, smp_processor_id());
+
+	if (trace_cpu_frequency_enabled()) {
+		for_each_cpu(cpu, policy->cpus)
+			trace_cpu_frequency(next_freq, cpu);
+	}
 }
 
 static void sugov_deferred_update(struct sugov_policy *sg_policy, u64 time,
Signature · 1 line
2.20.1
author maintainer
#144 lore raw

PATCH 137/203 x86/apic/vector: Warn when vector space exhaustion breaks affinity

In reply to Sasha Levin

From: Neil Horman <[email protected]>

[ Upstream commit 743dac494d61d991967ebcfab92e4f80dc7583b3 ]

On x86, CPUs are limited in the number of interrupts they can have affined to them as they only support 256 interrupt vectors per CPU. 32 vectors are reserved for the CPU and the kernel reserves another 22 for internal purposes. That leaves 202 vectors for assignement to devices.

When an interrupt is set up or the affinity is changed by the kernel or the administrator, the vector assignment code attempts to honor the requested affinity mask. If the vector space on the CPUs in that affinity mask is exhausted the code falls back to a wider set of CPUs and assigns a vector on a CPU outside of the requested affinity mask silently.

While the effective affinity is reflected in the corresponding /proc/irq/$N/effective_affinity* files the silent breakage of the requested affinity can lead to unexpected behaviour for administrators.

Add a pr_warn() when this happens so that adminstrators get at least informed about it in the syslog.

[ tglx: Massaged changelog and made the pr_warn() more informative ]

---
 arch/x86/kernel/apic/vector.c | 11 +++++++++++
 1 file changed, 11 insertions(+)
arch/x86/kernel/apic/vector.c +11 -0
index fdacb864c3dd4..2c5676b0a6e7f 100644
@@ -398,6 +398,17 @@ static int activate_reserved(struct irq_data *irqd)
 		if (!irqd_can_reserve(irqd))
 			apicd->can_reserve = false;
 	}
+
+	/*
+	 * Check to ensure that the effective affinity mask is a subset
+	 * the user supplied affinity mask, and warn the user if it is not
+	 */
+	if (!cpumask_subset(irq_data_get_effective_affinity_mask(irqd),
+			    irq_data_get_affinity_mask(irqd))) {
+		pr_warn("irq %u: Affinity broken due to vector space exhaustion.\n",
+			irqd->irq);
+	}
+
 	return ret;
 }
 
Signature · 1 line
2.20.1
author maintainer
#145 lore raw

PATCH 138/203 arm64: kpti: ensure patched kernel text is fetched from PoU

In reply to Sasha Levin

From: Mark Rutland <[email protected]>

[ Upstream commit f32c7a8e45105bd0af76872bf6eef0438ff12fb2 ]

While the MMUs is disabled, I-cache speculation can result in instructions being fetched from the PoC. During boot we may patch instructions (e.g. for alternatives and jump labels), and these may be dirty at the PoU (and stale at the PoC).

Thus, while the MMU is disabled in the KPTI pagetable fixup code we may load stale instructions into the I-cache, potentially leading to subsequent crashes when executing regions of code which have been modified at runtime.

Similarly to commit:

8ec41987436d566f ("arm64: mm: ensure patched kernel text is fetched from PoU")

... we can invalidate the I-cache after enabling the MMU to prevent such issues.

The KPTI pagetable fixup code itself should be clean to the PoC per the boot protocol, so no maintenance is required for this code.

---
 arch/arm64/mm/proc.S | 9 +++++++++
 1 file changed, 9 insertions(+)
arch/arm64/mm/proc.S +9 -0
index 7dbf2be470f6c..28a8f7b87ff06 100644
@@ -286,6 +286,15 @@ skip_pgd:
 	msr	sctlr_el1, x18
 	isb
 
+	/*
+	 * Invalidate the local I-cache so that any instructions fetched
+	 * speculatively from the PoC are discarded, since they may have
+	 * been dynamically patched at the PoU.
+	 */
+	ic	iallu
+	dsb	nsh
+	isb
+
 	/* Set the flag to zero to indicate that we're all done */
 	str	wzr, [flag_ptr]
 	ret
Signature · 1 line
2.20.1
author maintainer
#147 lore raw

PATCH 140/203 arm64: Use correct ll/sc atomic constraints

In reply to Sasha Levin

From: Andrew Murray <[email protected]>

[ Upstream commit 580fa1b874711d633f9b145b7777b0e83ebf3787 ]

The A64 ISA accepts distinct (but overlapping) ranges of immediates for:

* add arithmetic instructions ('I' machine constraint)
* sub arithmetic instructions ('J' machine constraint)
* 32-bit logical instructions ('K' machine constraint)
* 64-bit logical instructions ('L' machine constraint)

... but we currently use the 'I' constraint for many atomic operations using sub or logical instructions, which is not always valid.

When CONFIG_ARM64_LSE_ATOMICS is not set, this allows invalid immediates to be passed to instructions, potentially resulting in a build failure. When CONFIG_ARM64_LSE_ATOMICS is selected the out-of-line ll/sc atomics always use a register as they have no visibility of the value passed by the caller.

This patch adds a constraint parameter to the ATOMIC_xx and __CMPXCHG_CASE macros so that we can pass appropriate constraints for each case, with uses updated accordingly.

Unfortunately prior to GCC 8.1.0 the 'K' constraint erroneously accepted '4294967295', so we must instead force the use of a register.

---
 arch/arm64/include/asm/atomic_ll_sc.h | 89 ++++++++++++++-------------
 1 file changed, 47 insertions(+), 42 deletions(-)
arch/arm64/include/asm/atomic_ll_sc.h +47 -42
index c8c850bc3dfb0..6dd011e0b434a 100644
@@ -26,7 +26,7 @@
  * (the optimize attribute silently ignores these options).
  */
 
-#define ATOMIC_OP(op, asm_op)						\
+#define ATOMIC_OP(op, asm_op, constraint)				\
 __LL_SC_INLINE void							\
 __LL_SC_PREFIX(arch_atomic_##op(int i, atomic_t *v))			\
 {									\
@@ -40,11 +40,11 @@ __LL_SC_PREFIX(arch_atomic_##op(int i, atomic_t *v))			\
 "	stxr	%w1, %w0, %2\n"						\
 "	cbnz	%w1, 1b"						\
 	: "=&r" (result), "=&r" (tmp), "+Q" (v->counter)		\
-	: "Ir" (i));							\
+	: #constraint "r" (i));						\
 }									\
 __LL_SC_EXPORT(arch_atomic_##op);
 
-#define ATOMIC_OP_RETURN(name, mb, acq, rel, cl, op, asm_op)		\
+#define ATOMIC_OP_RETURN(name, mb, acq, rel, cl, op, asm_op, constraint)\
 __LL_SC_INLINE int							\
 __LL_SC_PREFIX(arch_atomic_##op##_return##name(int i, atomic_t *v))	\
 {									\
@@ -59,14 +59,14 @@ __LL_SC_PREFIX(arch_atomic_##op##_return##name(int i, atomic_t *v))	\
 "	cbnz	%w1, 1b\n"						\
 "	" #mb								\
 	: "=&r" (result), "=&r" (tmp), "+Q" (v->counter)		\
-	: "Ir" (i)							\
+	: #constraint "r" (i)						\
 	: cl);								\
 									\
 	return result;							\
 }									\
 __LL_SC_EXPORT(arch_atomic_##op##_return##name);
 
-#define ATOMIC_FETCH_OP(name, mb, acq, rel, cl, op, asm_op)		\
+#define ATOMIC_FETCH_OP(name, mb, acq, rel, cl, op, asm_op, constraint)	\
 __LL_SC_INLINE int							\
 __LL_SC_PREFIX(arch_atomic_fetch_##op##name(int i, atomic_t *v))	\
 {									\
@@ -81,7 +81,7 @@ __LL_SC_PREFIX(arch_atomic_fetch_##op##name(int i, atomic_t *v))	\
 "	cbnz	%w2, 1b\n"						\
 "	" #mb								\
 	: "=&r" (result), "=&r" (val), "=&r" (tmp), "+Q" (v->counter)	\
-	: "Ir" (i)							\
+	: #constraint "r" (i)						\
 	: cl);								\
 									\
 	return result;							\
@@ -99,8 +99,8 @@ __LL_SC_EXPORT(arch_atomic_fetch_##op##name);
 	ATOMIC_FETCH_OP (_acquire,        , a,  , "memory", __VA_ARGS__)\
 	ATOMIC_FETCH_OP (_release,        ,  , l, "memory", __VA_ARGS__)
 
-ATOMIC_OPS(add, add)
-ATOMIC_OPS(sub, sub)
+ATOMIC_OPS(add, add, I)
+ATOMIC_OPS(sub, sub, J)
 
 #undef ATOMIC_OPS
 #define ATOMIC_OPS(...)							\
@@ -110,17 +110,17 @@ ATOMIC_OPS(sub, sub)
 	ATOMIC_FETCH_OP (_acquire,        , a,  , "memory", __VA_ARGS__)\
 	ATOMIC_FETCH_OP (_release,        ,  , l, "memory", __VA_ARGS__)
 
-ATOMIC_OPS(and, and)
-ATOMIC_OPS(andnot, bic)
-ATOMIC_OPS(or, orr)
-ATOMIC_OPS(xor, eor)
+ATOMIC_OPS(and, and, )
+ATOMIC_OPS(andnot, bic, )
+ATOMIC_OPS(or, orr, )
+ATOMIC_OPS(xor, eor, )
 
 #undef ATOMIC_OPS
 #undef ATOMIC_FETCH_OP
 #undef ATOMIC_OP_RETURN
 #undef ATOMIC_OP
 
-#define ATOMIC64_OP(op, asm_op)						\
+#define ATOMIC64_OP(op, asm_op, constraint)				\
 __LL_SC_INLINE void							\
 __LL_SC_PREFIX(arch_atomic64_##op(s64 i, atomic64_t *v))		\
 {									\
@@ -134,11 +134,11 @@ __LL_SC_PREFIX(arch_atomic64_##op(s64 i, atomic64_t *v))		\
 "	stxr	%w1, %0, %2\n"						\
 "	cbnz	%w1, 1b"						\
 	: "=&r" (result), "=&r" (tmp), "+Q" (v->counter)		\
-	: "Ir" (i));							\
+	: #constraint "r" (i));						\
 }									\
 __LL_SC_EXPORT(arch_atomic64_##op);
 
-#define ATOMIC64_OP_RETURN(name, mb, acq, rel, cl, op, asm_op)		\
+#define ATOMIC64_OP_RETURN(name, mb, acq, rel, cl, op, asm_op, constraint)\
 __LL_SC_INLINE s64							\
 __LL_SC_PREFIX(arch_atomic64_##op##_return##name(s64 i, atomic64_t *v))\
 {									\
@@ -153,14 +153,14 @@ __LL_SC_PREFIX(arch_atomic64_##op##_return##name(s64 i, atomic64_t *v))\
 "	cbnz	%w1, 1b\n"						\
 "	" #mb								\
 	: "=&r" (result), "=&r" (tmp), "+Q" (v->counter)		\
-	: "Ir" (i)							\
+	: #constraint "r" (i)						\
 	: cl);								\
 									\
 	return result;							\
 }									\
 __LL_SC_EXPORT(arch_atomic64_##op##_return##name);
 
-#define ATOMIC64_FETCH_OP(name, mb, acq, rel, cl, op, asm_op)		\
+#define ATOMIC64_FETCH_OP(name, mb, acq, rel, cl, op, asm_op, constraint)\
 __LL_SC_INLINE s64							\
 __LL_SC_PREFIX(arch_atomic64_fetch_##op##name(s64 i, atomic64_t *v))	\
 {									\
@@ -175,7 +175,7 @@ __LL_SC_PREFIX(arch_atomic64_fetch_##op##name(s64 i, atomic64_t *v))	\
 "	cbnz	%w2, 1b\n"						\
 "	" #mb								\
 	: "=&r" (result), "=&r" (val), "=&r" (tmp), "+Q" (v->counter)	\
-	: "Ir" (i)							\
+	: #constraint "r" (i)						\
 	: cl);								\
 									\
 	return result;							\
@@ -193,8 +193,8 @@ __LL_SC_EXPORT(arch_atomic64_fetch_##op##name);
 	ATOMIC64_FETCH_OP (_acquire,, a,  , "memory", __VA_ARGS__)	\
 	ATOMIC64_FETCH_OP (_release,,  , l, "memory", __VA_ARGS__)
 
-ATOMIC64_OPS(add, add)
-ATOMIC64_OPS(sub, sub)
+ATOMIC64_OPS(add, add, I)
+ATOMIC64_OPS(sub, sub, J)
 
 #undef ATOMIC64_OPS
 #define ATOMIC64_OPS(...)						\
@@ -204,10 +204,10 @@ ATOMIC64_OPS(sub, sub)
 	ATOMIC64_FETCH_OP (_acquire,, a,  , "memory", __VA_ARGS__)	\
 	ATOMIC64_FETCH_OP (_release,,  , l, "memory", __VA_ARGS__)
 
-ATOMIC64_OPS(and, and)
-ATOMIC64_OPS(andnot, bic)
-ATOMIC64_OPS(or, orr)
-ATOMIC64_OPS(xor, eor)
+ATOMIC64_OPS(and, and, L)
+ATOMIC64_OPS(andnot, bic, )
+ATOMIC64_OPS(or, orr, L)
+ATOMIC64_OPS(xor, eor, L)
 
 #undef ATOMIC64_OPS
 #undef ATOMIC64_FETCH_OP
@@ -237,7 +237,7 @@ __LL_SC_PREFIX(arch_atomic64_dec_if_positive(atomic64_t *v))
 }
 __LL_SC_EXPORT(arch_atomic64_dec_if_positive);
 
-#define __CMPXCHG_CASE(w, sfx, name, sz, mb, acq, rel, cl)		\
+#define __CMPXCHG_CASE(w, sfx, name, sz, mb, acq, rel, cl, constraint)	\
 __LL_SC_INLINE u##sz							\
 __LL_SC_PREFIX(__cmpxchg_case_##name##sz(volatile void *ptr,		\
 					 unsigned long old,		\
@@ -265,29 +265,34 @@ __LL_SC_PREFIX(__cmpxchg_case_##name##sz(volatile void *ptr,		\
 	"2:"								\
 	: [tmp] "=&r" (tmp), [oldval] "=&r" (oldval),			\
 	  [v] "+Q" (*(u##sz *)ptr)					\
-	: [old] "Kr" (old), [new] "r" (new)				\
+	: [old] #constraint "r" (old), [new] "r" (new)			\
 	: cl);								\
 									\
 	return oldval;							\
 }									\
 __LL_SC_EXPORT(__cmpxchg_case_##name##sz);
 
-__CMPXCHG_CASE(w, b,     ,  8,        ,  ,  ,         )
-__CMPXCHG_CASE(w, h,     , 16,        ,  ,  ,         )
-__CMPXCHG_CASE(w,  ,     , 32,        ,  ,  ,         )
-__CMPXCHG_CASE( ,  ,     , 64,        ,  ,  ,         )
-__CMPXCHG_CASE(w, b, acq_,  8,        , a,  , "memory")
-__CMPXCHG_CASE(w, h, acq_, 16,        , a,  , "memory")
-__CMPXCHG_CASE(w,  , acq_, 32,        , a,  , "memory")
-__CMPXCHG_CASE( ,  , acq_, 64,        , a,  , "memory")
-__CMPXCHG_CASE(w, b, rel_,  8,        ,  , l, "memory")
-__CMPXCHG_CASE(w, h, rel_, 16,        ,  , l, "memory")
-__CMPXCHG_CASE(w,  , rel_, 32,        ,  , l, "memory")
-__CMPXCHG_CASE( ,  , rel_, 64,        ,  , l, "memory")
-__CMPXCHG_CASE(w, b,  mb_,  8, dmb ish,  , l, "memory")
-__CMPXCHG_CASE(w, h,  mb_, 16, dmb ish,  , l, "memory")
-__CMPXCHG_CASE(w,  ,  mb_, 32, dmb ish,  , l, "memory")
-__CMPXCHG_CASE( ,  ,  mb_, 64, dmb ish,  , l, "memory")
+/*
+ * Earlier versions of GCC (no later than 8.1.0) appear to incorrectly
+ * handle the 'K' constraint for the value 4294967295 - thus we use no
+ * constraint for 32 bit operations.
+ */
+__CMPXCHG_CASE(w, b,     ,  8,        ,  ,  ,         , )
+__CMPXCHG_CASE(w, h,     , 16,        ,  ,  ,         , )
+__CMPXCHG_CASE(w,  ,     , 32,        ,  ,  ,         , )
+__CMPXCHG_CASE( ,  ,     , 64,        ,  ,  ,         , L)
+__CMPXCHG_CASE(w, b, acq_,  8,        , a,  , "memory", )
+__CMPXCHG_CASE(w, h, acq_, 16,        , a,  , "memory", )
+__CMPXCHG_CASE(w,  , acq_, 32,        , a,  , "memory", )
+__CMPXCHG_CASE( ,  , acq_, 64,        , a,  , "memory", L)
+__CMPXCHG_CASE(w, b, rel_,  8,        ,  , l, "memory", )
+__CMPXCHG_CASE(w, h, rel_, 16,        ,  , l, "memory", )
+__CMPXCHG_CASE(w,  , rel_, 32,        ,  , l, "memory", )
+__CMPXCHG_CASE( ,  , rel_, 64,        ,  , l, "memory", L)
+__CMPXCHG_CASE(w, b,  mb_,  8, dmb ish,  , l, "memory", )
+__CMPXCHG_CASE(w, h,  mb_, 16, dmb ish,  , l, "memory", )
+__CMPXCHG_CASE(w,  ,  mb_, 32, dmb ish,  , l, "memory", )
+__CMPXCHG_CASE( ,  ,  mb_, 64, dmb ish,  , l, "memory", L)
 
 #undef __CMPXCHG_CASE
 
Signature · 1 line
2.20.1
author maintainer
#148 lore raw

PATCH 141/203 jump_label: Don't warn on __exit jump entries

In reply to Sasha Levin

From: Andrew Murray <[email protected]>

[ Upstream commit 8f35eaa5f2de020073a48ad51112237c5932cfcc ]

On architectures that discard .exit.* sections at runtime, a warning is printed for each jump label that is used within an in-kernel __exit annotated function:

can't patch jump_label at ehci_hcd_cleanup+0x8/0x3c

WARNING: CPU: 0 PID: 1 at kernel/jump_label.c:410 __jump_label_update+0x12c/0x138

As these functions will never get executed (they are free'd along with the rest of initmem) - we do not need to patch them and should not display any warnings.

The warning is displayed because the test required to satisfy jump_entry_is_init is based on init_section_contains (__init_begin to __init_end) whereas the test in __jump_label_update is based on init_kernel_text (_sinittext to _einittext) via kernel_text_address).

Fixes 19483677684b ("jump_label: Annotate entries that operate on __init code earlier")
---
 kernel/jump_label.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
kernel/jump_label.c +3 -1
index df3008419a1d0..cdb3ffab128b6 100644
@@ -407,7 +407,9 @@ static bool jump_label_can_update(struct jump_entry *entry, bool init)
 		return false;
 
 	if (!kernel_text_address(jump_entry_code(entry))) {
-		WARN_ONCE(1, "can't patch jump_label at %pS", (void *)jump_entry_code(entry));
+		WARN_ONCE(!jump_entry_is_init(entry),
+			  "can't patch jump_label at %pS",
+			  (void *)jump_entry_code(entry));
 		return false;
 	}
 
Signature · 1 line
2.20.1
author maintainer
#146 lore raw

PATCH 139/203 perf evlist: Use unshare(CLONE_FS) in sb threads to let setns(CLONE_NEWNS) work

In reply to Sasha Levin

From: Arnaldo Carvalho de Melo <[email protected]>

[ Upstream commit b397f8468fa27f08b83b348ffa56a226f72453af ]

When we started using a thread to catch the PERF_RECORD_BPF_EVENT meta data events to then ask the kernel for further info (BTF, etc) for BPF programs shortly after they get loaded, we forgot to use unshare(CLONE_FS) as was done in:

868a832918f6 ("perf top: Support lookup of symbols in other mount namespaces.")

Do it so that we can enter the namespaces to read the build-ids at the end of a 'perf record' session for the DSOs that had hits.

Before:

Starting a 'stress-ng --cpus 8' inside a container and then, outside the container running:

  # perf record -a --namespaces sleep 5
  # perf buildid-list | grep stress-ng
  #

We would end up with a 'perf.data' file that had no entry in its build-id table for the /usr/bin/stress-ng binary inside the container that got tons of PERF_RECORD_SAMPLEs.

After:

  # perf buildid-list | grep stress-ng
  f2ed02c68341183a124b9b0f6e2e6c493c465b29 /usr/bin/stress-ng
  #

Then its just a matter of making sure that that binary debuginfo package gets available in a place that 'perf report' will look at build-id keyed ELF files, which, in my case, on a f30 notebook, was a matter of installing the debuginfo file for the distro used in the container, fedora 31:

  # rpm -ivh http://fedora.c3sl.ufpr.br/linux/development/31/Everything/x86_64/debug/tree/Packages/s/stress-ng-debuginfo-0.07.29-10.fc31.x86_64.rpm

Then, because perf currently looks for those debuginfo files (richer ELF symtab) inside that namespace (look at the setns calls):

openat(AT_FDCWD, "/proc/self/ns/mnt", O_RDONLY) = 137
openat(AT_FDCWD, "/proc/13169/ns/mnt", O_RDONLY) = 139
setns(139, CLONE_NEWNS) = 0
stat("/usr/bin/stress-ng", {st_mode=S_IFREG|0755, st_size=3065416, ...}) = 0
openat(AT_FDCWD, "/usr/bin/stress-ng", O_RDONLY) = 140
fcntl(140, F_GETFD) = 0
fstat(140, {st_mode=S_IFREG|0755, st_size=3065416, ...}) = 0
mmap(NULL, 3065416, PROT_READ, MAP_PRIVATE, 140, 0) = 0x7ff2fdc5b000
munmap(0x7ff2fdc5b000, 3065416) = 0
close(140) = 0
stat("stress-ng-0.07.29-10.fc31.x86_64.debug", 0x7fff45d71260) = -1 ENOENT (No such file or directory) stat("/usr/bin/stress-ng-0.07.29-10.fc31.x86_64.debug", 0x7fff45d71260) = -1 ENOENT (No such file or directory) stat("/usr/bin/.debug/stress-ng-0.07.29-10.fc31.x86_64.debug", 0x7fff45d71260) = -1 ENOENT (No such file or directory) stat("/usr/lib/debug/usr/bin/stress-ng-0.07.29-10.fc31.x86_64.debug", 0x7fff45d71260) = -1 ENOENT (No such file or directory) stat("/root/.debug/.build-id/f2/ed02c68341183a124b9b0f6e2e6c493c465b29", 0x7fff45d711e0) = -1 ENOENT (No such file or directory)

To only then go back to the "host" namespace to look just in the users's ~/.debug cache:

  setns(137, CLONE_NEWNS)                 = 0
  chdir("/root")                          = 0
  close(137)                              = 0
  close(139)                              = 0

stat("/root/.debug/.build-id/f2/ed02c68341183a124b9b0f6e2e6c493c465b29/elf", 0x7fff45d732e0) = -1 ENOENT (No such file or directory)

It continues to fail to resolve symbols:

  # perf report | grep stress-ng | head -5
     9.50%  stress-ng-cpu    stress-ng    [.] 0x0000000000021ac1
     8.58%  stress-ng-cpu    stress-ng    [.] 0x0000000000021ab4
     8.51%  stress-ng-cpu    stress-ng    [.] 0x0000000000021489
     7.17%  stress-ng-cpu    stress-ng    [.] 0x00000000000219b6
     3.93%  stress-ng-cpu    stress-ng    [.] 0x0000000000021478
  #

To overcome that we use:

  # perf buildid-cache -v --add /usr/lib/debug/usr/bin/stress-ng-0.07.29-10.fc31.x86_64.debug
  Adding f2ed02c68341183a124b9b0f6e2e6c493c465b29 /usr/lib/debug/usr/bin/stress-ng-0.07.29-10.fc31.x86_64.debug: Ok
  #
  # ls -la /root/.debug/.build-id/f2/ed02c68341183a124b9b0f6e2e6c493c465b29/elf
  -rw-r--r--. 3 root root 2401184 Jul 27 07:03 /root/.debug/.build-id/f2/ed02c68341183a124b9b0f6e2e6c493c465b29/elf
  # file /root/.debug/.build-id/f2/ed02c68341183a124b9b0f6e2e6c493c465b29/elf
  /root/.debug/.build-id/f2/ed02c68341183a124b9b0f6e2e6c493c465b29/elf: ELF 64-bit LSB shared object, x86-64, version 1 (SYSV), dynamically linked, interpreter \004, BuildID[sha1]=f2ed02c68341183a124b9b0f6e2e6c493c465b29, for GNU/Linux 3.2.0, with debug_info, not stripped, too many notes (256)
  #

Now it finally works:

  # perf report | grep stress-ng | head -5
    23.59%  stress-ng-cpu    stress-ng    [.] ackermann
    23.33%  stress-ng-cpu    stress-ng    [.] is_prime
    17.36%  stress-ng-cpu    stress-ng    [.] stress_cpu_sieve
     6.08%  stress-ng-cpu    stress-ng    [.] stress_cpu_correlate
     3.55%  stress-ng-cpu    stress-ng    [.] queens_try
  #

I'll make sure that it looks for the build-id keyed files in both the "host" namespace (the namespace the user running 'perf record' was a the time of the recording) and in the container namespace, as it shouldn't matter where a content based key lookup finds the ELF file to use in resolving symbols, etc.

Cc Alexander Shishkin <[email protected]>
Cc Alexei Starovoitov <[email protected]>
Cc Brendan Gregg <[email protected]>
Cc Daniel Borkmann <[email protected]>
Cc Krister Johansen <[email protected]>
Cc Namhyung Kim <[email protected]>
Cc Peter Zijlstra <[email protected]>
Cc Song Liu <[email protected]>
Cc Stanislav Fomichev <[email protected]>
Cc Thomas-Mich Richter <[email protected]>
Fixes 657ee5531903 ("perf evlist: Introduce side band thread")
---
 tools/perf/util/evlist.c | 9 +++++++++
 1 file changed, 9 insertions(+)
tools/perf/util/evlist.c +9 -0
index b0364d923f764..070c3bd578827 100644
@@ -20,6 +20,7 @@
 #include "bpf-event.h"
 #include <signal.h>
 #include <unistd.h>
+#include <sched.h>
 
 #include "parse-events.h"
 #include <subcmd/parse-options.h>
@@ -1870,6 +1871,14 @@ static void *perf_evlist__poll_thread(void *arg)
 	struct perf_evlist *evlist = arg;
 	bool draining = false;
 	int i, done = 0;
+	/*
+	 * In order to read symbols from other namespaces perf to needs to call
+	 * setns(2).  This isn't permitted if the struct_fs has multiple users.
+	 * unshare(2) the fs so that we may continue to setns into namespaces
+	 * that we're observing when, for instance, reading the build-ids at
+	 * the end of a 'perf record' session.
+	 */
+	unshare(CLONE_FS);
 
 	while (!done) {
 		bool got_data = false;
Signature · 1 line
2.20.1
author maintainer
#155 lore raw

PATCH 148/203 arm64: lse: Make ARM64_LSE_ATOMICS depend on JUMP_LABEL

In reply to Sasha Levin

From: Will Deacon <[email protected]>

[ Upstream commit b32baf91f60fb9c7010bff87e68132f2ce31d9a8 ]

Support for LSE atomic instructions (CONFIG_ARM64_LSE_ATOMICS) relies on a static key to select between the legacy LL/SC implementation which is available on all arm64 CPUs and the super-duper LSE implementation which is available on CPUs implementing v8.1 and later.

Unfortunately, when building a kernel with CONFIG_JUMP_LABEL disabled (e.g. because the toolchain doesn't support 'asm goto'), the static key inside the atomics code tries to use atomics itself. This results in a mess of circular includes and a build failure:

In file included from ./arch/arm64/include/asm/lse.h:11,

                 from ./arch/arm64/include/asm/atomic.h:16,
                 from ./include/linux/atomic.h:7,
                 from ./include/asm-generic/bitops/atomic.h:5,
                 from ./arch/arm64/include/asm/bitops.h:26,
                 from ./include/linux/bitops.h:19,
                 from ./include/linux/kernel.h:12,
                 from ./include/asm-generic/bug.h:18,
                 from ./arch/arm64/include/asm/bug.h:26,
                 from ./include/linux/bug.h:5,
                 from ./include/linux/page-flags.h:10,
                 from kernel/bounds.c:10:
./include/linux/jump_label.h: In function ‘static_key_count’:
./include/linux/jump_label.h:254:9: error: implicit declaration of function ‘atomic_read’ [-Werror=implicit-function-declaration]
  return atomic_read(&key->enabled);
         ^~~~~~~~~~~

[ ... more of the same ... ]

Since LSE atomic instructions are not critical to the operation of the kernel, make them depend on JUMP_LABEL at compile time.

---
 arch/arm64/Kconfig | 1 +
 1 file changed, 1 insertion(+)
arch/arm64/Kconfig +1 -0
index 3adcec05b1f67..27405ac94228b 100644
@@ -1263,6 +1263,7 @@ config ARM64_PAN
 
 config ARM64_LSE_ATOMICS
 	bool "Atomic instructions"
+	depends on JUMP_LABEL
 	default y
 	help
 	  As part of the Large System Extensions, ARMv8.1 introduces new
Signature · 1 line
2.20.1
author maintainer
#150 lore raw

PATCH 143/203 ASoC: fsl_ssi: Fix clock control issue in master mode

In reply to Sasha Levin

From: Shengjiu Wang <[email protected]>

[ Upstream commit 696d05225cebffd172008d212657be90e823eac0 ]

The test case is
arecord -Dhw:0 -d 10 -f S16_LE -r 48000 -c 2 temp.wav & aplay -Dhw:0 -d 30 -f S16_LE -r 48000 -c 2 test.wav

There will be error after end of arecord:
aplay: pcm_write:2051: write error: Input/output error

Capture and Playback work in parallel in master mode, one substream stops, the other substream is impacted, the reason is that clock is disabled wrongly.

The clock's reference count is not increased when second substream starts, the hw_param() function returns in the beginning because first substream is enabled, then in end of first substream, the hw_free() disables the clock.

This patch is to move the clock enablement to the place before checking of the device enablement in hw_param().

---
 sound/soc/fsl/fsl_ssi.c | 18 +++++++++---------
 1 file changed, 9 insertions(+), 9 deletions(-)
sound/soc/fsl/fsl_ssi.c +9 -9
index fa862af25c1a3..085855f9b08d4 100644
@@ -799,15 +799,6 @@ static int fsl_ssi_hw_params(struct snd_pcm_substream *substream,
 	u32 wl = SSI_SxCCR_WL(sample_size);
 	int ret;
 
-	/*
-	 * SSI is properly configured if it is enabled and running in
-	 * the synchronous mode; Note that AC97 mode is an exception
-	 * that should set separate configurations for STCCR and SRCCR
-	 * despite running in the synchronous mode.
-	 */
-	if (ssi->streams && ssi->synchronous)
-		return 0;
-
 	if (fsl_ssi_is_i2s_master(ssi)) {
 		ret = fsl_ssi_set_bclk(substream, dai, hw_params);
 		if (ret)
@@ -823,6 +814,15 @@ static int fsl_ssi_hw_params(struct snd_pcm_substream *substream,
 		}
 	}
 
+	/*
+	 * SSI is properly configured if it is enabled and running in
+	 * the synchronous mode; Note that AC97 mode is an exception
+	 * that should set separate configurations for STCCR and SRCCR
+	 * despite running in the synchronous mode.
+	 */
+	if (ssi->streams && ssi->synchronous)
+		return 0;
+
 	if (!fsl_ssi_is_ac97(ssi)) {
 		/*
 		 * Keep the ssi->i2s_net intact while having a local variable
Signature · 1 line
2.20.1
author maintainer
#156 lore raw

PATCH 149/203 iommu/amd: Silence warnings under memory pressure

In reply to Sasha Levin

From: Qian Cai <[email protected]>

[ Upstream commit 3d708895325b78506e8daf00ef31549476e8586a ]

When running heavy memory pressure workloads, the system is throwing endless warnings,

smartpqi 0000:23:00.0: AMD-Vi: IOMMU mapping error in map_sg (io-pages:
5 reason: -12)

Hardware name: HPE ProLiant DL385 Gen10/ProLiant DL385 Gen10, BIOS A40
07/10/2019
swapper/10: page allocation failure: order:0, mode:0xa20(GFP_ATOMIC),
nodemask=(null),cpuset=/,mems_allowed=0,4
Call Trace:
 <IRQ>
 dump_stack+0x62/0x9a
 warn_alloc.cold.43+0x8a/0x148
 __alloc_pages_nodemask+0x1a5c/0x1bb0
 get_zeroed_page+0x16/0x20
 iommu_map_page+0x477/0x540
 map_sg+0x1ce/0x2f0
 scsi_dma_map+0xc6/0x160
 pqi_raid_submit_scsi_cmd_with_io_request+0x1c3/0x470 [smartpqi]
 do_IRQ+0x81/0x170
 common_interrupt+0xf/0xf
 </IRQ>

because the allocation could fail from iommu_map_page(), and the volume of this call could be huge which may generate a lot of serial console output and cosumes all CPUs.

Fix it by silencing the warning in this call site, and there is still a dev_err() later to notify the failure.

---
 drivers/iommu/amd_iommu.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/iommu/amd_iommu.c +3 -1
index 61de81965c44e..e1259429ded2f 100644
@@ -2577,7 +2577,9 @@ static int map_sg(struct device *dev, struct scatterlist *sglist,
 
 			bus_addr  = address + s->dma_address + (j << PAGE_SHIFT);
 			phys_addr = (sg_phys(s) & PAGE_MASK) + (j << PAGE_SHIFT);
-			ret = iommu_map_page(domain, bus_addr, phys_addr, PAGE_SIZE, prot, GFP_ATOMIC);
+			ret = iommu_map_page(domain, bus_addr, phys_addr,
+					     PAGE_SIZE, prot,
+					     GFP_ATOMIC | __GFP_NOWARN);
 			if (ret)
 				goto out_unmap;
 
Signature · 6 lines
2.20.1

_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu
author maintainer
#152 lore raw

PATCH 145/203 nvmet: fix data units read and written counters in SMART log

In reply to Sasha Levin

From: Tom Wu <[email protected]>

[ Upstream commit 3bec2e3754becebd4c452999adb49bc62c575ea4 ]

In nvme spec 1.3 there is a definition for data write/read counters from SMART log, (See section 5.14.1.2):
This value is reported in thousands (i.e., a value of 1 corresponds to 1000 units of 512 bytes read) and is rounded up.

However, in nvme target where value is reported with actual units, but not thousands of units as the spec requires.

---
 drivers/nvme/target/admin-cmd.c | 14 ++++++++------
 1 file changed, 8 insertions(+), 6 deletions(-)
drivers/nvme/target/admin-cmd.c +8 -6
index 4dc12ea52f23c..51800a9ce9a91 100644
@@ -81,9 +81,11 @@ static u16 nvmet_get_smart_log_nsid(struct nvmet_req *req,
 		goto out;
 
 	host_reads = part_stat_read(ns->bdev->bd_part, ios[READ]);
-	data_units_read = part_stat_read(ns->bdev->bd_part, sectors[READ]);
+	data_units_read = DIV_ROUND_UP(part_stat_read(ns->bdev->bd_part,
+		sectors[READ]), 1000);
 	host_writes = part_stat_read(ns->bdev->bd_part, ios[WRITE]);
-	data_units_written = part_stat_read(ns->bdev->bd_part, sectors[WRITE]);
+	data_units_written = DIV_ROUND_UP(part_stat_read(ns->bdev->bd_part,
+		sectors[WRITE]), 1000);
 
 	put_unaligned_le64(host_reads, &slog->host_reads[0]);
 	put_unaligned_le64(data_units_read, &slog->data_units_read[0]);
@@ -111,11 +113,11 @@ static u16 nvmet_get_smart_log_all(struct nvmet_req *req,
 		if (!ns->bdev)
 			continue;
 		host_reads += part_stat_read(ns->bdev->bd_part, ios[READ]);
-		data_units_read +=
-			part_stat_read(ns->bdev->bd_part, sectors[READ]);
+		data_units_read += DIV_ROUND_UP(
+			part_stat_read(ns->bdev->bd_part, sectors[READ]), 1000);
 		host_writes += part_stat_read(ns->bdev->bd_part, ios[WRITE]);
-		data_units_written +=
-			part_stat_read(ns->bdev->bd_part, sectors[WRITE]);
+		data_units_written += DIV_ROUND_UP(
+			part_stat_read(ns->bdev->bd_part, sectors[WRITE]), 1000);
 
 	}
 	rcu_read_unlock();
Signature · 7 lines
2.20.1


_______________________________________________
Linux-nvme mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-nvme
author maintainer
#157 lore raw

PATCH 150/203 ASoC: Intel: Haswell: Adjust machine device private context

In reply to Sasha Levin

From: Cezary Rojewski <[email protected]>

[ Upstream commit ca964edf0ddbfec2cb10b3d251d09598e7ca9b13 ]

Apart from Haswell machines, all other devices have their private data set to snd_soc_acpi_mach instance.

Changes for HSW/ BDW boards introduced with series:
https://patchwork.kernel.org/cover/10782035/

added support for dai_link platform_name adjustments within card probe routines. These take for granted private_data points to snd_soc_acpi_mach whereas for Haswell, it's sst_pdata instead. Change private context of platform_device - representing machine board - to address this.

Fixes e87055d732e3 ("ASoC: Intel: haswell: platform name fixup support")
Fixes 7e40ddcf974a ("ASoC: Intel: bdw-rt5677: platform name fixup support")
Fixes 2d067b2807f9 ("ASoC: Intel: broadwell: platform name fixup support")
---
 sound/soc/intel/common/sst-acpi.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
sound/soc/intel/common/sst-acpi.c +2 -1
index 0e8e0a7a11df3..5854868650b9e 100644
@@ -141,11 +141,12 @@ static int sst_acpi_probe(struct platform_device *pdev)
 	}
 
 	platform_set_drvdata(pdev, sst_acpi);
+	mach->pdata = sst_pdata;
 
 	/* register machine driver */
 	sst_acpi->pdev_mach =
 		platform_device_register_data(dev, mach->drv_name, -1,
-					      sst_pdata, sizeof(*sst_pdata));
+					      mach, sizeof(*mach));
 	if (IS_ERR(sst_acpi->pdev_mach))
 		return PTR_ERR(sst_acpi->pdev_mach);
 
Signature · 1 line
2.20.1
author maintainer
#158 lore raw

PATCH 151/203 libata/ahci: Drop PCS quirk for Denverton and beyond

In reply to Sasha Levin

From: Dan Williams <[email protected]>

[ Upstream commit c312ef176399e04fc5f7f2809d9a589751fbf6d9 ]

The Linux ahci driver has historically implemented a configuration fixup for platforms / platform-firmware that fails to enable the ports prior to OS hand-off at boot. The fixup was originally implemented way back before ahci moved from drivers/scsi/ to drivers/ata/, and was updated in 2007 via commit 49f290903935 "ahci: update PCS programming". The quirk sets a port-enable bitmap in the PCS register at offset 0x92.

This quirk could be applied generically up until the arrival of the Denverton (DNV) platform. The DNV AHCI controller architecture supports more than 6 ports and along with that the PCS register location and format were updated to allow for more possible ports in the bitmap. DNV AHCI expands the register to 32-bits and moves it to offset 0x94.

As it stands there are no known problem reports with existing Linux trying to set bits at offset 0x92 which indicates that the quirk is not applicable. Likely it is not applicable on a wider range of platforms, but it is difficult to discern which platforms if any still depend on the quirk.

Rather than try to fix the PCS quirk to consider the DNV register layout instead require explicit opt-in. The assumption is that the OS driver need not touch this register, and platforms can be added with a new boad_ahci_pcs7 board-id when / if problematic platforms are found in the future. The logic in ahci_intel_pcs_quirk() looks for all Intel AHCI instances with "legacy" board-ids and otherwise skips the quirk if the board was matched by class-code.

---
 drivers/ata/ahci.c | 116 +++++++++++++++++++++++++++------------------
 drivers/ata/ahci.h |   2 +
 2 files changed, 71 insertions(+), 47 deletions(-)
drivers/ata/ahci.c +69 -47
index f7652baa63370..3e63294304c72 100644
@@ -65,6 +65,12 @@ enum board_ids {
 	board_ahci_sb700,	/* for SB700 and SB800 */
 	board_ahci_vt8251,
 
+	/*
+	 * board IDs for Intel chipsets that support more than 6 ports
+	 * *and* end up needing the PCS quirk.
+	 */
+	board_ahci_pcs7,
+
 	/* aliases */
 	board_ahci_mcp_linux	= board_ahci_mcp65,
 	board_ahci_mcp67	= board_ahci_mcp65,
@@ -220,6 +226,12 @@ static const struct ata_port_info ahci_port_info[] = {
 		.udma_mask	= ATA_UDMA6,
 		.port_ops	= &ahci_vt8251_ops,
 	},
+	[board_ahci_pcs7] = {
+		.flags		= AHCI_FLAG_COMMON,
+		.pio_mask	= ATA_PIO4,
+		.udma_mask	= ATA_UDMA6,
+		.port_ops	= &ahci_ops,
+	},
 };
 
 static const struct pci_device_id ahci_pci_tbl[] = {
@@ -264,26 +276,26 @@ static const struct pci_device_id ahci_pci_tbl[] = {
 	{ PCI_VDEVICE(INTEL, 0x3b2b), board_ahci }, /* PCH RAID */
 	{ PCI_VDEVICE(INTEL, 0x3b2c), board_ahci_mobile }, /* PCH M RAID */
 	{ PCI_VDEVICE(INTEL, 0x3b2f), board_ahci }, /* PCH AHCI */
-	{ PCI_VDEVICE(INTEL, 0x19b0), board_ahci }, /* DNV AHCI */
-	{ PCI_VDEVICE(INTEL, 0x19b1), board_ahci }, /* DNV AHCI */
-	{ PCI_VDEVICE(INTEL, 0x19b2), board_ahci }, /* DNV AHCI */
-	{ PCI_VDEVICE(INTEL, 0x19b3), board_ahci }, /* DNV AHCI */
-	{ PCI_VDEVICE(INTEL, 0x19b4), board_ahci }, /* DNV AHCI */
-	{ PCI_VDEVICE(INTEL, 0x19b5), board_ahci }, /* DNV AHCI */
-	{ PCI_VDEVICE(INTEL, 0x19b6), board_ahci }, /* DNV AHCI */
-	{ PCI_VDEVICE(INTEL, 0x19b7), board_ahci }, /* DNV AHCI */
-	{ PCI_VDEVICE(INTEL, 0x19bE), board_ahci }, /* DNV AHCI */
-	{ PCI_VDEVICE(INTEL, 0x19bF), board_ahci }, /* DNV AHCI */
-	{ PCI_VDEVICE(INTEL, 0x19c0), board_ahci }, /* DNV AHCI */
-	{ PCI_VDEVICE(INTEL, 0x19c1), board_ahci }, /* DNV AHCI */
-	{ PCI_VDEVICE(INTEL, 0x19c2), board_ahci }, /* DNV AHCI */
-	{ PCI_VDEVICE(INTEL, 0x19c3), board_ahci }, /* DNV AHCI */
-	{ PCI_VDEVICE(INTEL, 0x19c4), board_ahci }, /* DNV AHCI */
-	{ PCI_VDEVICE(INTEL, 0x19c5), board_ahci }, /* DNV AHCI */
-	{ PCI_VDEVICE(INTEL, 0x19c6), board_ahci }, /* DNV AHCI */
-	{ PCI_VDEVICE(INTEL, 0x19c7), board_ahci }, /* DNV AHCI */
-	{ PCI_VDEVICE(INTEL, 0x19cE), board_ahci }, /* DNV AHCI */
-	{ PCI_VDEVICE(INTEL, 0x19cF), board_ahci }, /* DNV AHCI */
+	{ PCI_VDEVICE(INTEL, 0x19b0), board_ahci_pcs7 }, /* DNV AHCI */
+	{ PCI_VDEVICE(INTEL, 0x19b1), board_ahci_pcs7 }, /* DNV AHCI */
+	{ PCI_VDEVICE(INTEL, 0x19b2), board_ahci_pcs7 }, /* DNV AHCI */
+	{ PCI_VDEVICE(INTEL, 0x19b3), board_ahci_pcs7 }, /* DNV AHCI */
+	{ PCI_VDEVICE(INTEL, 0x19b4), board_ahci_pcs7 }, /* DNV AHCI */
+	{ PCI_VDEVICE(INTEL, 0x19b5), board_ahci_pcs7 }, /* DNV AHCI */
+	{ PCI_VDEVICE(INTEL, 0x19b6), board_ahci_pcs7 }, /* DNV AHCI */
+	{ PCI_VDEVICE(INTEL, 0x19b7), board_ahci_pcs7 }, /* DNV AHCI */
+	{ PCI_VDEVICE(INTEL, 0x19bE), board_ahci_pcs7 }, /* DNV AHCI */
+	{ PCI_VDEVICE(INTEL, 0x19bF), board_ahci_pcs7 }, /* DNV AHCI */
+	{ PCI_VDEVICE(INTEL, 0x19c0), board_ahci_pcs7 }, /* DNV AHCI */
+	{ PCI_VDEVICE(INTEL, 0x19c1), board_ahci_pcs7 }, /* DNV AHCI */
+	{ PCI_VDEVICE(INTEL, 0x19c2), board_ahci_pcs7 }, /* DNV AHCI */
+	{ PCI_VDEVICE(INTEL, 0x19c3), board_ahci_pcs7 }, /* DNV AHCI */
+	{ PCI_VDEVICE(INTEL, 0x19c4), board_ahci_pcs7 }, /* DNV AHCI */
+	{ PCI_VDEVICE(INTEL, 0x19c5), board_ahci_pcs7 }, /* DNV AHCI */
+	{ PCI_VDEVICE(INTEL, 0x19c6), board_ahci_pcs7 }, /* DNV AHCI */
+	{ PCI_VDEVICE(INTEL, 0x19c7), board_ahci_pcs7 }, /* DNV AHCI */
+	{ PCI_VDEVICE(INTEL, 0x19cE), board_ahci_pcs7 }, /* DNV AHCI */
+	{ PCI_VDEVICE(INTEL, 0x19cF), board_ahci_pcs7 }, /* DNV AHCI */
 	{ PCI_VDEVICE(INTEL, 0x1c02), board_ahci }, /* CPT AHCI */
 	{ PCI_VDEVICE(INTEL, 0x1c03), board_ahci_mobile }, /* CPT M AHCI */
 	{ PCI_VDEVICE(INTEL, 0x1c04), board_ahci }, /* CPT RAID */
@@ -623,30 +635,6 @@ static void ahci_pci_save_initial_config(struct pci_dev *pdev,
 	ahci_save_initial_config(&pdev->dev, hpriv);
 }
 
-static int ahci_pci_reset_controller(struct ata_host *host)
-{
-	struct pci_dev *pdev = to_pci_dev(host->dev);
-	int rc;
-
-	rc = ahci_reset_controller(host);
-	if (rc)
-		return rc;
-
-	if (pdev->vendor == PCI_VENDOR_ID_INTEL) {
-		struct ahci_host_priv *hpriv = host->private_data;
-		u16 tmp16;
-
-		/* configure PCS */
-		pci_read_config_word(pdev, 0x92, &tmp16);
-		if ((tmp16 & hpriv->port_map) != hpriv->port_map) {
-			tmp16 |= hpriv->port_map;
-			pci_write_config_word(pdev, 0x92, tmp16);
-		}
-	}
-
-	return 0;
-}
-
 static void ahci_pci_init_controller(struct ata_host *host)
 {
 	struct ahci_host_priv *hpriv = host->private_data;
@@ -849,7 +837,7 @@ static int ahci_pci_device_runtime_resume(struct device *dev)
 	struct ata_host *host = pci_get_drvdata(pdev);
 	int rc;
 
-	rc = ahci_pci_reset_controller(host);
+	rc = ahci_reset_controller(host);
 	if (rc)
 		return rc;
 	ahci_pci_init_controller(host);
@@ -884,7 +872,7 @@ static int ahci_pci_device_resume(struct device *dev)
 		ahci_mcp89_apple_enable(pdev);
 
 	if (pdev->dev.power.power_state.event == PM_EVENT_SUSPEND) {
-		rc = ahci_pci_reset_controller(host);
+		rc = ahci_reset_controller(host);
 		if (rc)
 			return rc;
 
@@ -1619,6 +1607,34 @@ static void ahci_update_initial_lpm_policy(struct ata_port *ap,
 		ap->target_lpm_policy = policy;
 }
 
+static void ahci_intel_pcs_quirk(struct pci_dev *pdev, struct ahci_host_priv *hpriv)
+{
+	const struct pci_device_id *id = pci_match_id(ahci_pci_tbl, pdev);
+	u16 tmp16;
+
+	/*
+	 * Only apply the 6-port PCS quirk for known legacy platforms.
+	 */
+	if (!id || id->vendor != PCI_VENDOR_ID_INTEL)
+		return;
+	if (((enum board_ids) id->driver_data) < board_ahci_pcs7)
+		return;
+
+	/*
+	 * port_map is determined from PORTS_IMPL PCI register which is
+	 * implemented as write or write-once register.  If the register
+	 * isn't programmed, ahci automatically generates it from number
+	 * of ports, which is good enough for PCS programming. It is
+	 * otherwise expected that platform firmware enables the ports
+	 * before the OS boots.
+	 */
+	pci_read_config_word(pdev, PCS_6, &tmp16);
+	if ((tmp16 & hpriv->port_map) != hpriv->port_map) {
+		tmp16 |= hpriv->port_map;
+		pci_write_config_word(pdev, PCS_6, tmp16);
+	}
+}
+
 static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
 {
 	unsigned int board_id = ent->driver_data;
@@ -1731,6 +1747,12 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
 	/* save initial config */
 	ahci_pci_save_initial_config(pdev, hpriv);
 
+	/*
+	 * If platform firmware failed to enable ports, try to enable
+	 * them here.
+	 */
+	ahci_intel_pcs_quirk(pdev, hpriv);
+
 	/* prepare host */
 	if (hpriv->cap & HOST_CAP_NCQ) {
 		pi.flags |= ATA_FLAG_NCQ;
@@ -1840,7 +1862,7 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
 	if (rc)
 		return rc;
 
-	rc = ahci_pci_reset_controller(host);
+	rc = ahci_reset_controller(host);
 	if (rc)
 		return rc;
 
drivers/ata/ahci.h +2 -0
index 0570629d719d8..3dbf398c92eaf 100644
@@ -247,6 +247,8 @@ enum {
 					  ATA_FLAG_ACPI_SATA | ATA_FLAG_AN,
 
 	ICH_MAP				= 0x90, /* ICH MAP register */
+	PCS_6				= 0x92, /* 6 port PCS */
+	PCS_7				= 0x94, /* 7+ port PCS (Denverton) */
 
 	/* em constants */
 	EM_MAX_SLOTS			= 8,
Signature · 1 line
2.20.1
author maintainer
#159 lore raw

PATCH 152/203 iommu/iova: Avoid false sharing on fq_timer_on

In reply to Sasha Levin

From: Eric Dumazet <[email protected]>

[ Upstream commit 0d87308cca2c124f9bce02383f1d9632c9be89c4 ]

In commit 14bd9a607f90 ("iommu/iova: Separate atomic variables to improve performance") Jinyu Qi identified that the atomic_cmpxchg() in queue_iova() was causing a performance loss and moved critical fields so that the false sharing would not impact them.

However, avoiding the false sharing in the first place seems easy. We should attempt the atomic_cmpxchg() no more than 100 times per second. Adding an atomic_read() will keep the cache line mostly shared.

This false sharing came with commit 9a005a800ae8
("iommu/iova: Add flush timer").

Fixes 9a005a800ae8 ('iommu/iova: Add flush timer')
Cc Jinyu Qi <[email protected]>
Cc Joerg Roedel <[email protected]>
---
 drivers/iommu/iova.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/iommu/iova.c +3 -1
index 3e1a8a6755723..41c605b0058f9 100644
@@ -577,7 +577,9 @@ void queue_iova(struct iova_domain *iovad,
 
 	spin_unlock_irqrestore(&fq->lock, flags);
 
-	if (atomic_cmpxchg(&iovad->fq_timer_on, 0, 1) == 0)
+	/* Avoid false sharing as much as possible. */
+	if (!atomic_read(&iovad->fq_timer_on) &&
+	    !atomic_cmpxchg(&iovad->fq_timer_on, 0, 1))
 		mod_timer(&iovad->fq_timer,
 			  jiffies + msecs_to_jiffies(IOVA_FQ_TIMEOUT));
 }
Signature · 6 lines
2.20.1

_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu
author maintainer
#153 lore raw

PATCH 146/203 nvme-multipath: fix ana log nsid lookup when nsid is not found

In reply to Sasha Levin

From: Anton Eidelman <[email protected]>

[ Upstream commit e01f91dff91c7b16a6e3faf2565017d497a73f83 ]

ANA log parsing invokes nvme_update_ana_state() per ANA group desc. This updates the state of namespaces with nsids in desc->nsids[].

Both ctrl->namespaces list and desc->nsids[] array are sorted by nsid. Hence nvme_update_ana_state() performs a single walk over ctrl->namespaces:
- if current namespace matches the current desc->nsids[n],
this namespace is updated, and n is incremented.
- the process stops when it encounters the end of either ctrl->namespaces end or desc->nsids[]

In case desc->nsids[n] does not match any of ctrl->namespaces, the remaining nsids following desc->nsids[n] will not be updated. Such situation was considered abnormal and generated WARN_ON_ONCE.

However ANA log MAY contain nsids not (yet) found in ctrl->namespaces. For example, lets consider the following scenario:
- nvme0 exposes namespaces with nsids = [2, 3] to the host
- a new namespace nsid = 1 is added dynamically
- also, a ANA topology change is triggered
- NS_CHANGED aen is generated and triggers scan_work
- before scan_work discovers nsid=1 and creates a namespace, a NOTICE_ANA aen was issues and ana_work receives ANA log with nsids=[1, 2, 3]

Result: ana_work fails to update ANA state on existing namespaces [2, 3]

Solution:
Change the way nvme_update_ana_state() namespace list walk checks the current namespace against desc->nsids[n] as follows:
a) ns->head->ns_id < desc->nsids[n]: keep walking ctrl->namespaces.
b) ns->head->ns_id == desc->nsids[n]: match, update the namespace
c) ns->head->ns_id >= desc->nsids[n]: skip to desc->nsids[n+1]

This enables correct operation in the scenario described above. This also allows ANA log to contain nsids currently invisible to the host, i.e. inactive nsids.

---
 drivers/nvme/host/multipath.c | 8 +++++---
 1 file changed, 5 insertions(+), 3 deletions(-)
drivers/nvme/host/multipath.c +5 -3
index af831d3d15d07..30de7efef0035 100644
@@ -509,14 +509,16 @@ static int nvme_update_ana_state(struct nvme_ctrl *ctrl,
 
 	down_write(&ctrl->namespaces_rwsem);
 	list_for_each_entry(ns, &ctrl->namespaces, list) {
-		if (ns->head->ns_id != le32_to_cpu(desc->nsids[n]))
+		unsigned nsid = le32_to_cpu(desc->nsids[n]);
+
+		if (ns->head->ns_id < nsid)
 			continue;
-		nvme_update_ns_ana_state(desc, ns);
+		if (ns->head->ns_id == nsid)
+			nvme_update_ns_ana_state(desc, ns);
 		if (++n == nr_nsids)
 			break;
 	}
 	up_write(&ctrl->namespaces_rwsem);
-	WARN_ON_ONCE(n < nr_nsids);
 	return 0;
 }
 
Signature · 7 lines
2.20.1


_______________________________________________
Linux-nvme mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-nvme
author maintainer
#160 lore raw

PATCH 153/203 libtraceevent: Change users plugin directory

In reply to Sasha Levin

From: Tzvetomir Stoyanov <[email protected]>

[ Upstream commit e97fd1383cd77c467d2aed7fa4e596789df83977 ]

To be compliant with XDG user directory layout, the user's plugin directory is changed from ~/.traceevent/plugins to ~/.local/lib/traceevent/plugins/

---
 tools/lib/traceevent/Makefile       | 6 +++---
 tools/lib/traceevent/event-plugin.c | 2 +-
 2 files changed, 4 insertions(+), 4 deletions(-)
tools/lib/traceevent/Makefile +3 -3
index 3292c290654f6..86ce17a1f7fb6 100644
@@ -62,15 +62,15 @@ set_plugin_dir := 1
 
 # Set plugin_dir to preffered global plugin location
 # If we install under $HOME directory we go under
-# $(HOME)/.traceevent/plugins
+# $(HOME)/.local/lib/traceevent/plugins
 #
 # We dont set PLUGIN_DIR in case we install under $HOME
 # directory, because by default the code looks under:
-# $(HOME)/.traceevent/plugins by default.
+# $(HOME)/.local/lib/traceevent/plugins by default.
 #
 ifeq ($(plugin_dir),)
 ifeq ($(prefix),$(HOME))
-override plugin_dir = $(HOME)/.traceevent/plugins
+override plugin_dir = $(HOME)/.local/lib/traceevent/plugins
 set_plugin_dir := 0
 else
 override plugin_dir = $(libdir)/traceevent/plugins
tools/lib/traceevent/event-plugin.c +1 -1
index 8ca28de9337a5..e1f7ddd5a6cf0 100644
@@ -18,7 +18,7 @@
 #include "event-utils.h"
 #include "trace-seq.h"
 
-#define LOCAL_PLUGIN_DIR ".traceevent/plugins"
+#define LOCAL_PLUGIN_DIR ".local/lib/traceevent/plugins/"
 
 static struct registered_plugin_options {
 	struct registered_plugin_options	*next;
Signature · 1 line
2.20.1
author maintainer
#167 lore raw

PATCH 160/203 hwmon: (k10temp) Add support for AMD family 17h, model 70h CPUs

In reply to Sasha Levin

From: Marcel Bocu <[email protected]>

[ Upstream commit 12163cfbfc0f804cc7d27bc20e8d266ce7459260 ]

It would seem like model 70h is behaving in the same way as model 30h, so let's just add the new F3 PCI ID to the list of compatible devices.

Unlike previous Ryzen/Threadripper, Ryzen gen 3 processors do not need temperature offsets anymore. This has been reported in the press and verified on my Ryzen 3700X by checking that the idle temperature reported by k10temp is matching the temperature reported by the firmware.

Vicki Pfau sent an identical patch after I checked that no-one had written this patch. I would have been happy about dropping my patch but unlike for his patch series, I had already Cc:ed the x86 people and they already reviewed the changes. Since Vicki has not answered to any email after his initial series, let's assume she is on vacation and let's avoid duplication of reviews from the maintainers and merge my series. To acknowledge Vicki's anteriority, I added her S-o-b to the patch.

v2, suggested by Guenter Roeck and Brian Woods:
- rename from 71h to 70h

---
 drivers/hwmon/k10temp.c | 1 +
 1 file changed, 1 insertion(+)
drivers/hwmon/k10temp.c +1 -0
index c77e89239dcd9..5c1dddde193c3 100644
@@ -349,6 +349,7 @@ static const struct pci_device_id k10temp_id_table[] = {
 	{ PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_17H_DF_F3) },
 	{ PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_17H_M10H_DF_F3) },
 	{ PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_17H_M30H_DF_F3) },
+	{ PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_17H_M70H_DF_F3) },
 	{ PCI_VDEVICE(HYGON, PCI_DEVICE_ID_AMD_17H_DF_F3) },
 	{}
 };
Signature · 1 line
2.20.1
author maintainer
#168 lore raw

PATCH 161/203 hwmon: (acpi_power_meter) Change log level for 'unsafe software power cap'

In reply to Sasha Levin

From: Wang Shenran <[email protected]>

[ Upstream commit 6e4d91aa071810deac2cd052161aefb376ecf04e ]

At boot time, the acpi_power_meter driver logs the following error level
message: "Ignoring unsafe software power cap". Having read about it from a few sources, it seems that the error message can be quite misleading.

While the message can imply that Linux is ignoring the fact that the system is operating in potentially dangerous conditions, the truth is the driver found an ACPI_PMC object that supports software power capping. The driver simply decides not to use it, perhaps because it doesn't support the object.

The best solution is probably changing the log level from error to warning. All sources I have found, regarding the error, have downplayed its significance. There is not much of a reason for it to be on error level, while causing potential confusions or misinterpretations.

---
 drivers/hwmon/acpi_power_meter.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/hwmon/acpi_power_meter.c +2 -2
index 6ba1a08253f0a..4cf25458f0b95 100644
@@ -681,8 +681,8 @@ static int setup_attrs(struct acpi_power_meter_resource *resource)
 
 	if (resource->caps.flags & POWER_METER_CAN_CAP) {
 		if (!can_cap_in_hardware()) {
-			dev_err(&resource->acpi_dev->dev,
-				"Ignoring unsafe software power cap!\n");
+			dev_warn(&resource->acpi_dev->dev,
+				 "Ignoring unsafe software power cap!\n");
 			goto skip_unsafe_cap;
 		}
 
Signature · 1 line
2.20.1
author maintainer
#170 lore raw

PATCH 163/203 dmaengine: ti: edma: Do not reset reserved paRAM slots

In reply to Sasha Levin

From: Peter Ujfalusi <[email protected]>

[ Upstream commit c5dbe60664b3660f5ac5854e21273ea2e7ff698f ]

Skip resetting paRAM slots marked as reserved as they might be used by other cores.

---
 drivers/dma/ti/edma.c | 9 ++++++---
 1 file changed, 6 insertions(+), 3 deletions(-)
drivers/dma/ti/edma.c +6 -3
index ceabdea40ae0f..982631d4e1f8a 100644
@@ -2273,9 +2273,6 @@ static int edma_probe(struct platform_device *pdev)
 
 	ecc->default_queue = info->default_queue;
 
-	for (i = 0; i < ecc->num_slots; i++)
-		edma_write_slot(ecc, i, &dummy_paramset);
-
 	if (info->rsv) {
 		/* Set the reserved slots in inuse list */
 		rsv_slots = info->rsv->rsv_slots;
@@ -2288,6 +2285,12 @@ static int edma_probe(struct platform_device *pdev)
 		}
 	}
 
+	for (i = 0; i < ecc->num_slots; i++) {
+		/* Reset only unused - not reserved - paRAM slots */
+		if (!test_bit(i, ecc->slot_inuse))
+			edma_write_slot(ecc, i, &dummy_paramset);
+	}
+
 	/* Clear the xbar mapped channels in unused list */
 	xbar_chans = info->xbar_chans;
 	if (xbar_chans) {
Signature · 1 line
2.20.1
author maintainer
#171 lore raw

PATCH 164/203 kprobes: Prohibit probing on BUG() and WARN() address

In reply to Sasha Levin

From: Masami Hiramatsu <[email protected]>

[ Upstream commit e336b4027775cb458dc713745e526fa1a1996b2a ]

Since BUG() and WARN() may use a trap (e.g. UD2 on x86) to get the address where the BUG() has occurred, kprobes can not do single-step out-of-line that instruction. So prohibit probing on such address.

Without this fix, if someone put a kprobe on WARN(), the kernel will crash with invalid opcode error instead of outputing warning message, because kernel can not find correct bug address.

---
 include/linux/bug.h | 5 +++++
 kernel/kprobes.c    | 3 ++-
 2 files changed, 7 insertions(+), 1 deletion(-)
include/linux/bug.h +5 -0
index fe5916550da8c..f639bd0122f39 100644
@@ -47,6 +47,11 @@ void generic_bug_clear_once(void);
 
 #else	/* !CONFIG_GENERIC_BUG */
 
+static inline void *find_bug(unsigned long bugaddr)
+{
+	return NULL;
+}
+
 static inline enum bug_trap_type report_bug(unsigned long bug_addr,
 					    struct pt_regs *regs)
 {
kernel/kprobes.c +2 -1
index d9770a5393c89..ebe8315a756a2 100644
@@ -1514,7 +1514,8 @@ static int check_kprobe_address_safe(struct kprobe *p,
 	/* Ensure it is not in reserved area nor out of text */
 	if (!kernel_text_address((unsigned long) p->addr) ||
 	    within_kprobe_blacklist((unsigned long) p->addr) ||
-	    jump_label_text_reserved(p->addr, p->addr)) {
+	    jump_label_text_reserved(p->addr, p->addr) ||
+	    find_bug((unsigned long)p->addr)) {
 		ret = -EINVAL;
 		goto out;
 	}
Signature · 1 line
2.20.1
author maintainer
#164 lore raw

PATCH 157/203 ACPI: custom_method: fix memory leaks

In reply to Sasha Levin

From: Wenwen Wang <[email protected]>

[ Upstream commit 03d1571d9513369c17e6848476763ebbd10ec2cb ]

In cm_write(), 'buf' is allocated through kzalloc(). In the following execution, if an error occurs, 'buf' is not deallocated, leading to memory leaks. To fix this issue, free 'buf' before returning the error.

Fixes 526b4af47f44 ("ACPI: Split out custom_method functionality into an own driver")
---
 drivers/acpi/custom_method.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)
drivers/acpi/custom_method.c +4 -1
index b2ef4c2ec955d..fd66a736621cf 100644
@@ -49,8 +49,10 @@ static ssize_t cm_write(struct file *file, const char __user * user_buf,
 	if ((*ppos > max_size) ||
 	    (*ppos + count > max_size) ||
 	    (*ppos + count < count) ||
-	    (count > uncopied_bytes))
+	    (count > uncopied_bytes)) {
+		kfree(buf);
 		return -EINVAL;
+	}
 
 	if (copy_from_user(buf + (*ppos), user_buf, count)) {
 		kfree(buf);
@@ -70,6 +72,7 @@ static ssize_t cm_write(struct file *file, const char __user * user_buf,
 		add_taint(TAINT_OVERRIDDEN_ACPI_TABLE, LOCKDEP_NOW_UNRELIABLE);
 	}
 
+	kfree(buf);
 	return count;
 }
 
Signature · 1 line
2.20.1
author maintainer
#174 lore raw

PATCH 167/203 s390/crypto: xts-aes-s390 fix extra run-time crypto self tests finding

In reply to Sasha Levin

From: Harald Freudenberger <[email protected]>

[ Upstream commit 9e323d45ba94262620a073a3f9945ca927c07c71 ]

With 'extra run-time crypto self tests' enabled, the selftest for s390-xts fails with

alg: skcipher: xts-aes-s390 encryption unexpectedly succeeded on test vector "random: len=0 klen=64"; expected_error=-22, cfg="random: inplace use_digest nosimd src_divs=[2.61%@+4006, 84.44%@+21, 1.55%@+13, 4.50%@+344, 4.26%@+21, 2.64%@+27]"

This special case with nbytes=0 is not handled correctly and this fix now makes sure that -EINVAL is returned when there is en/decrypt called with 0 bytes to en/decrypt.

---
 arch/s390/crypto/aes_s390.c | 6 ++++++
 1 file changed, 6 insertions(+)
arch/s390/crypto/aes_s390.c +6 -0
index d00f84add5f4c..6d2dbb5089d5c 100644
@@ -586,6 +586,9 @@ static int xts_aes_encrypt(struct blkcipher_desc *desc,
 	struct s390_xts_ctx *xts_ctx = crypto_blkcipher_ctx(desc->tfm);
 	struct blkcipher_walk walk;
 
+	if (!nbytes)
+		return -EINVAL;
+
 	if (unlikely(!xts_ctx->fc))
 		return xts_fallback_encrypt(desc, dst, src, nbytes);
 
@@ -600,6 +603,9 @@ static int xts_aes_decrypt(struct blkcipher_desc *desc,
 	struct s390_xts_ctx *xts_ctx = crypto_blkcipher_ctx(desc->tfm);
 	struct blkcipher_walk walk;
 
+	if (!nbytes)
+		return -EINVAL;
+
 	if (unlikely(!xts_ctx->fc))
 		return xts_fallback_decrypt(desc, dst, src, nbytes);
 
Signature · 1 line
2.20.1
author maintainer
#173 lore raw

PATCH 166/203 irqchip/sifive-plic: set max threshold for ignored handlers

In reply to Sasha Levin

From: Christoph Hellwig <[email protected]>

[ Upstream commit 9ce06497c2722a0f9109e4cc3ce35b7a69617886 ]

When running in M-mode, the S-mode plic handlers are still listed in the device tree. Ignore them by setting the maximum threshold.

---
 drivers/irqchip/irq-sifive-plic.c | 12 ++++++++++--
 1 file changed, 10 insertions(+), 2 deletions(-)
drivers/irqchip/irq-sifive-plic.c +10 -2
index cf755964f2f8b..c72c036aea768 100644
@@ -244,6 +244,7 @@ static int __init plic_init(struct device_node *node,
 		struct plic_handler *handler;
 		irq_hw_number_t hwirq;
 		int cpu, hartid;
+		u32 threshold = 0;
 
 		if (of_irq_parse_one(node, i, &parent)) {
 			pr_err("failed to parse parent for context %d.\n", i);
@@ -266,10 +267,16 @@ static int __init plic_init(struct device_node *node,
 			continue;
 		}
 
+		/*
+		 * When running in M-mode we need to ignore the S-mode handler.
+		 * Here we assume it always comes later, but that might be a
+		 * little fragile.
+		 */
 		handler = per_cpu_ptr(&plic_handlers, cpu);
 		if (handler->present) {
 			pr_warn("handler already present for context %d.\n", i);
-			continue;
+			threshold = 0xffffffff;
+			goto done;
 		}
 
 		handler->present = true;
@@ -279,8 +286,9 @@ static int __init plic_init(struct device_node *node,
 		handler->enable_base =
 			plic_regs + ENABLE_BASE + i * ENABLE_PER_HART;
 
+done:
 		/* priority must be > threshold to trigger an interrupt */
-		writel(0, handler->hart_base + CONTEXT_THRESHOLD);
+		writel(threshold, handler->hart_base + CONTEXT_THRESHOLD);
 		for (hwirq = 1; hwirq <= nr_irqs; hwirq++)
 			plic_toggle(handler, hwirq, 0);
 		nr_handlers++;
Signature · 7 lines
2.20.1


_______________________________________________
linux-riscv mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-riscv
author maintainer
#181 lore raw

PATCH 170/203 x86/cpu: Add Tiger Lake to Intel family

In reply to Sasha Levin

From: Gayatri Kammela <[email protected]>

[ Upstream commit 6e1c32c5dbb4b90eea8f964c2869d0bde050dbe0 ]

Add the model numbers/CPUIDs of Tiger Lake mobile and desktop to the Intel family.

---
 arch/x86/include/asm/intel-family.h | 3 +++
 1 file changed, 3 insertions(+)
arch/x86/include/asm/intel-family.h +3 -0
index fe7c205233f1c..9ae1c0f05fd2d 100644
@@ -73,6 +73,9 @@
 #define INTEL_FAM6_ICELAKE_MOBILE	0x7E
 #define INTEL_FAM6_ICELAKE_NNPI		0x9D
 
+#define INTEL_FAM6_TIGERLAKE_L		0x8C
+#define INTEL_FAM6_TIGERLAKE		0x8D
+
 /* "Small Core" Processors (Atom) */
 
 #define INTEL_FAM6_ATOM_BONNELL		0x1C /* Diamondville, Pineview */
Signature · 1 line
2.20.1
author maintainer
#184 lore raw

PATCH 173/203 ASoC: es8316: support fixed and variable both clock rates

In reply to Sasha Levin

From: Katsuhiro Suzuki <[email protected]>

[ Upstream commit ebe02a5b9ef05e3b812af3d628cdf6206d9ba610 ]

This patch supports some type of machine drivers that set 0 to mclk when sound device goes to idle state. After applied this patch, sysclk == 0 means there is no constraint of sound rate and other values will set constraints which is derived by sysclk setting.

Original code refuses sysclk == 0 setting. But some boards and SoC (such as RockPro64 and RockChip I2S) has connected SoC MCLK out to ES8316 MCLK in. In this case, SoC side I2S will choose suitable frequency of MCLK such as fs * mclk-fs when user starts playing or capturing.

Bad scenario as follows (mclk-fs = 256):
- Initialize sysclk by correct value (Ex. 12.288MHz)

    - ES8316 set constraints of PCM rate by sysclk
      48kHz (1/256), 32kHz (1/384), 30.720kHz (1/400),
      24kHz (1/512), 16kHz (1/768), 12kHz (1/1024)

- Play 48kHz sound, it's acceptable
- Sysclk is not changed

- Play 32kHz sound, it's acceptable
- Set sysclk by 8.192MHz (= fs * mclk-fs = 32k * 256)

    - ES8316 set constraints of PCM rate by sysclk
      32kHz (1/256), 21.33kHz (1/384), 20.48kHz (1/400),
      16kHz (1/512), 10.66kHz (1/768), 8kHz (1/1024)

- Play 48kHz again, but it's NOT acceptable because constraints list does not allow 48kHz

---
 sound/soc/codecs/es8316.c | 35 ++++++++++++++++++++---------------
 1 file changed, 20 insertions(+), 15 deletions(-)
sound/soc/codecs/es8316.c +20 -15
index 96d04896193f2..c47b3c4bb06c7 100644
@@ -368,8 +368,12 @@ static int es8316_set_dai_sysclk(struct snd_soc_dai *codec_dai,
 
 	es8316->sysclk = freq;
 
-	if (freq == 0)
+	if (freq == 0) {
+		es8316->sysclk_constraints.list = NULL;
+		es8316->sysclk_constraints.count = 0;
+
 		return 0;
+	}
 
 	/* Limit supported sample rates to ones that can be autodetected
 	 * by the codec running in slave mode.
@@ -444,17 +448,10 @@ static int es8316_pcm_startup(struct snd_pcm_substream *substream,
 	struct snd_soc_component *component = dai->component;
 	struct es8316_priv *es8316 = snd_soc_component_get_drvdata(component);
 
-	if (es8316->sysclk == 0) {
-		dev_err(component->dev, "No sysclk provided\n");
-		return -EINVAL;
-	}
-
-	/* The set of sample rates that can be supported depends on the
-	 * MCLK supplied to the CODEC.
-	 */
-	snd_pcm_hw_constraint_list(substream->runtime, 0,
-				   SNDRV_PCM_HW_PARAM_RATE,
-				   &es8316->sysclk_constraints);
+	if (es8316->sysclk_constraints.list)
+		snd_pcm_hw_constraint_list(substream->runtime, 0,
+					   SNDRV_PCM_HW_PARAM_RATE,
+					   &es8316->sysclk_constraints);
 
 	return 0;
 }
@@ -466,11 +463,19 @@ static int es8316_pcm_hw_params(struct snd_pcm_substream *substream,
 	struct snd_soc_component *component = dai->component;
 	struct es8316_priv *es8316 = snd_soc_component_get_drvdata(component);
 	u8 wordlen = 0;
+	int i;
 
-	if (!es8316->sysclk) {
-		dev_err(component->dev, "No MCLK configured\n");
-		return -EINVAL;
+	/* Validate supported sample rates that are autodetected from MCLK */
+	for (i = 0; i < NR_SUPPORTED_MCLK_LRCK_RATIOS; i++) {
+		const unsigned int ratio = supported_mclk_lrck_ratios[i];
+
+		if (es8316->sysclk % ratio != 0)
+			continue;
+		if (es8316->sysclk / ratio == params_rate(params))
+			break;
 	}
+	if (i == NR_SUPPORTED_MCLK_LRCK_RATIOS)
+		return -EINVAL;
 
 	switch (params_format(params)) {
 	case SNDRV_PCM_FORMAT_S16_LE:
Signature · 1 line
2.20.1
author maintainer
#172 lore raw

PATCH 165/203 x86/mm: Fix cpumask_of_node() error condition

In reply to Sasha Levin

From: Peter Zijlstra <[email protected]>

[ Upstream commit bc04a049f058a472695aa22905d57e2b1f4c77d9 ]

When CONFIG_DEBUG_PER_CPU_MAPS=y we validate that the @node argument of cpumask_of_node() is a valid node_id. It however forgets to check for negative numbers. Fix this by explicitly casting to unsigned int.

(unsigned)node >= nr_node_ids

verifies: 0 <= node < nr_node_ids

Also ammend the error message to match the condition.

---
 arch/x86/mm/numa.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
arch/x86/mm/numa.c +2 -2
index e6dad600614c2..4123100e0eafe 100644
@@ -861,9 +861,9 @@ void numa_remove_cpu(int cpu)
  */
 const struct cpumask *cpumask_of_node(int node)
 {
-	if (node >= nr_node_ids) {
+	if ((unsigned)node >= nr_node_ids) {
 		printk(KERN_WARNING
-			"cpumask_of_node(%d): node > nr_node_ids(%u)\n",
+			"cpumask_of_node(%d): (unsigned)node >= nr_node_ids(%u)\n",
 			node, nr_node_ids);
 		dump_stack();
 		return cpu_none_mask;
Signature · 1 line
2.20.1
author maintainer
#201 lore raw

PATCH 188/203 media: technisat-usb2: break out of loop at end of buffer

In reply to Sasha Levin

From: Sean Young <[email protected]>

[ Upstream commit 0c4df39e504bf925ab666132ac3c98d6cbbe380b ]

Ensure we do not access the buffer beyond the end if no 0xff byte is encountered.

---
 drivers/media/usb/dvb-usb/technisat-usb2.c | 22 ++++++++++------------
 1 file changed, 10 insertions(+), 12 deletions(-)
drivers/media/usb/dvb-usb/technisat-usb2.c +10 -12
index c659e18b358b8..676d233d46d53 100644
@@ -608,10 +608,9 @@ static int technisat_usb2_frontend_attach(struct dvb_usb_adapter *a)
 static int technisat_usb2_get_ir(struct dvb_usb_device *d)
 {
 	struct technisat_usb2_state *state = d->priv;
-	u8 *buf = state->buf;
-	u8 *b;
-	int ret;
 	struct ir_raw_event ev;
+	u8 *buf = state->buf;
+	int i, ret;
 
 	buf[0] = GET_IR_DATA_VENDOR_REQUEST;
 	buf[1] = 0x08;
@@ -647,26 +646,25 @@ static int technisat_usb2_get_ir(struct dvb_usb_device *d)
 		return 0; /* no key pressed */
 
 	/* decoding */
-	b = buf+1;
 
 #if 0
 	deb_rc("RC: %d ", ret);
-	debug_dump(b, ret, deb_rc);
+	debug_dump(buf + 1, ret, deb_rc);
 #endif
 
 	ev.pulse = 0;
-	while (1) {
-		ev.pulse = !ev.pulse;
-		ev.duration = (*b * FIRMWARE_CLOCK_DIVISOR * FIRMWARE_CLOCK_TICK) / 1000;
-		ir_raw_event_store(d->rc_dev, &ev);
-
-		b++;
-		if (*b == 0xff) {
+	for (i = 1; i < ARRAY_SIZE(state->buf); i++) {
+		if (buf[i] == 0xff) {
 			ev.pulse = 0;
 			ev.duration = 888888*2;
 			ir_raw_event_store(d->rc_dev, &ev);
 			break;
 		}
+
+		ev.pulse = !ev.pulse;
+		ev.duration = (buf[i] * FIRMWARE_CLOCK_DIVISOR *
+			       FIRMWARE_CLOCK_TICK) / 1000;
+		ir_raw_event_store(d->rc_dev, &ev);
 	}
 
 	ir_raw_event_handle(d->rc_dev);
Signature · 1 line
2.20.1
author maintainer
#203 lore raw

PATCH 190/203 e1000e: add workaround for possible stalled packet

In reply to Sasha Levin

From: Kai-Heng Feng <[email protected]>

[ Upstream commit e5e9a2ecfe780975820e157b922edee715710b66 ]

This works around a possible stalled packet issue, which may occur due to clock recovery from the PCH being too slow, when the LAN is transitioning from K1 at 1G link speed.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=204057

---
 drivers/net/ethernet/intel/e1000e/ich8lan.c | 10 ++++++++++
 drivers/net/ethernet/intel/e1000e/ich8lan.h |  2 +-
 2 files changed, 11 insertions(+), 1 deletion(-)
drivers/net/ethernet/intel/e1000e/ich8lan.c +10 -0
index 395b057014809..a1fab77b2096a 100644
@@ -1429,6 +1429,16 @@ static s32 e1000_check_for_copper_link_ich8lan(struct e1000_hw *hw)
 			else
 				phy_reg |= 0xFA;
 			e1e_wphy_locked(hw, I217_PLL_CLOCK_GATE_REG, phy_reg);
+
+			if (speed == SPEED_1000) {
+				hw->phy.ops.read_reg_locked(hw, HV_PM_CTRL,
+							    &phy_reg);
+
+				phy_reg |= HV_PM_CTRL_K1_CLK_REQ;
+
+				hw->phy.ops.write_reg_locked(hw, HV_PM_CTRL,
+							     phy_reg);
+			}
 		}
 		hw->phy.ops.release(hw);
 
drivers/net/ethernet/intel/e1000e/ich8lan.h +1 -1
index eb09c755fa172..1502895eb45dd 100644
@@ -210,7 +210,7 @@
 
 /* PHY Power Management Control */
 #define HV_PM_CTRL		PHY_REG(770, 17)
-#define HV_PM_CTRL_PLL_STOP_IN_K1_GIGA	0x100
+#define HV_PM_CTRL_K1_CLK_REQ		0x200
 #define HV_PM_CTRL_K1_ENABLE		0x4000
 
 #define I217_PLL_CLOCK_GATE_REG	PHY_REG(772, 28)
Signature · 1 line
2.20.1
author maintainer
#189 lore raw

PATCH 176/203 tools/power/x86/intel-speed-select: Fix memory leak

In reply to Sasha Levin

From: Prarit Bhargava <[email protected]>

[ Upstream commit 3bc3d30ca324bfc3045a1a7fe1f5fe5ad5d92fd9 ]

cpumasks are allocated by calling the alloc_cpu_mask() function and are never free'd. They should be free'd after the commands have run.

Fix the memory leaks by calling free_cpu_set().

---
 tools/power/x86/intel-speed-select/isst-config.c | 16 +++++++++++-----
 1 file changed, 11 insertions(+), 5 deletions(-)
tools/power/x86/intel-speed-select/isst-config.c +11 -5
index 91c5ad1685a15..6a10dea01eefc 100644
@@ -603,6 +603,10 @@ static int isst_fill_platform_info(void)
 
 	close(fd);
 
+	if (isst_platform_info.api_version > supported_api_ver) {
+		printf("Incompatible API versions; Upgrade of tool is required\n");
+		return -1;
+	}
 	return 0;
 }
 
@@ -1529,6 +1533,7 @@ static void cmdline(int argc, char **argv)
 {
 	int opt;
 	int option_index = 0;
+	int ret;
 
 	static struct option long_options[] = {
 		{ "cpu", required_argument, 0, 'c' },
@@ -1590,13 +1595,14 @@ static void cmdline(int argc, char **argv)
 	set_max_cpu_num();
 	set_cpu_present_cpu_mask();
 	set_cpu_target_cpu_mask();
-	isst_fill_platform_info();
-	if (isst_platform_info.api_version > supported_api_ver) {
-		printf("Incompatible API versions; Upgrade of tool is required\n");
-		exit(0);
-	}
+	ret = isst_fill_platform_info();
+	if (ret)
+		goto out;
 
 	process_command(argc, argv);
+out:
+	free_cpu_set(present_cpumask);
+	free_cpu_set(target_cpumask);
 }
 
 int main(int argc, char **argv)
Signature · 1 line
2.20.1
author maintainer
#209 lore raw

PATCH 196/203 ALSA: hda/realtek - Blacklist PC beep for Lenovo ThinkCentre M73/93

In reply to Sasha Levin

From: Takashi Iwai <[email protected]>

[ Upstream commit 051c78af14fcd74a22b5af45548ad9d588247cc7 ]

Lenovo ThinkCentre M73 and M93 don't seem to have a proper beep although the driver tries to probe and set up blindly. Blacklist these machines for suppressing the beep creation.

---
 sound/pci/hda/patch_realtek.c | 3 +++
 1 file changed, 3 insertions(+)
sound/pci/hda/patch_realtek.c +3 -0
index 1bec62720374d..d223a79ac934f 100644
@@ -1058,6 +1058,9 @@ static const struct snd_pci_quirk beep_white_list[] = {
 	SND_PCI_QUIRK(0x1043, 0x834a, "EeePC", 1),
 	SND_PCI_QUIRK(0x1458, 0xa002, "GA-MA790X", 1),
 	SND_PCI_QUIRK(0x8086, 0xd613, "Intel", 1),
+	/* blacklist -- no beep available */
+	SND_PCI_QUIRK(0x17aa, 0x309e, "Lenovo ThinkCentre M73", 0),
+	SND_PCI_QUIRK(0x17aa, 0x30a3, "Lenovo ThinkCentre M93", 0),
 	{}
 };
 
Signature · 1 line
2.20.1
author maintainer
#210 lore raw

PATCH 197/203 iommu/amd: Override wrong IVRS IOAPIC on Raven Ridge systems

In reply to Sasha Levin

From: Kai-Heng Feng <[email protected]>

[ Upstream commit 93d051550ee02eaff9a2541d825605a7bd778027 ]

Raven Ridge systems may have malfunction touchpad or hang at boot if incorrect IVRS IOAPIC is provided by BIOS.

Users already found correct "ivrs_ioapic=" values, let's put them inside kernel to workaround buggy BIOS.

---
 drivers/iommu/Makefile           |  2 +-
 drivers/iommu/amd_iommu.h        | 14 +++++
 drivers/iommu/amd_iommu_init.c   |  5 +-
 drivers/iommu/amd_iommu_quirks.c | 92 ++++++++++++++++++++++++++++++++
 4 files changed, 111 insertions(+), 2 deletions(-)
 create mode 100644 drivers/iommu/amd_iommu.h
 create mode 100644 drivers/iommu/amd_iommu_quirks.c
drivers/iommu/Makefile +1 -1
index f13f36ae1af65..c6a277e698484 100644
@@ -10,7 +10,7 @@ obj-$(CONFIG_IOMMU_IO_PGTABLE_LPAE) += io-pgtable-arm.o
 obj-$(CONFIG_IOMMU_IOVA) += iova.o
 obj-$(CONFIG_OF_IOMMU)	+= of_iommu.o
 obj-$(CONFIG_MSM_IOMMU) += msm_iommu.o
-obj-$(CONFIG_AMD_IOMMU) += amd_iommu.o amd_iommu_init.o
+obj-$(CONFIG_AMD_IOMMU) += amd_iommu.o amd_iommu_init.o amd_iommu_quirks.o
 obj-$(CONFIG_AMD_IOMMU_DEBUGFS) += amd_iommu_debugfs.o
 obj-$(CONFIG_AMD_IOMMU_V2) += amd_iommu_v2.o
 obj-$(CONFIG_ARM_SMMU) += arm-smmu.o
drivers/iommu/amd_iommu.h new file +14 -0
new file mode 100644
index 0000000000000..12d540d9b59b0
@@ -0,0 +1,14 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+
+#ifndef AMD_IOMMU_H
+#define AMD_IOMMU_H
+
+int __init add_special_device(u8 type, u8 id, u16 *devid, bool cmd_line);
+
+#ifdef CONFIG_DMI
+void amd_iommu_apply_ivrs_quirks(void);
+#else
+static void amd_iommu_apply_ivrs_quirks(void) { }
+#endif
+
+#endif
drivers/iommu/amd_iommu_init.c +4 -1
index 4413aa67000e5..568c52317757c 100644
@@ -32,6 +32,7 @@
 #include <asm/irq_remapping.h>
 
 #include <linux/crash_dump.h>
+#include "amd_iommu.h"
 #include "amd_iommu_proto.h"
 #include "amd_iommu_types.h"
 #include "irq_remapping.h"
@@ -1002,7 +1003,7 @@ static void __init set_dev_entry_from_acpi(struct amd_iommu *iommu,
 	set_iommu_for_device(iommu, devid);
 }
 
-static int __init add_special_device(u8 type, u8 id, u16 *devid, bool cmd_line)
+int __init add_special_device(u8 type, u8 id, u16 *devid, bool cmd_line)
 {
 	struct devid_map *entry;
 	struct list_head *list;
@@ -1153,6 +1154,8 @@ static int __init init_iommu_from_acpi(struct amd_iommu *iommu,
 	if (ret)
 		return ret;
 
+	amd_iommu_apply_ivrs_quirks();
+
 	/*
 	 * First save the recommended feature enable bits from ACPI
 	 */
drivers/iommu/amd_iommu_quirks.c new file +92 -0

92 lines not on this page · raw message

Signature · 6 lines
2.20.1

_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu
author maintainer
#215 lore raw

PATCH 202/203 btrfs: Detect unbalanced tree with empty leaf before crashing btree operations

In reply to Sasha Levin

From: Qu Wenruo <[email protected]>

[ Upstream commit 62fdaa52a3d00a875da771719b6dc537ca79fce1 ]

[BUG]
With crafted image, btrfs will panic at btree operations:

kernel BUG at fs/btrfs/ctree.c:3894!
invalid opcode: 0000 [#1] SMP PTI

  CPU: 0 PID: 1138 Comm: btrfs-transacti Not tainted 5.0.0-rc8+ #9
  RIP: 0010:__push_leaf_left+0x6b6/0x6e0
  RSP: 0018:ffffc0bd4128b990 EFLAGS: 00010246
  RAX: 0000000000000000 RBX: ffffa0a4ab8f0e38 RCX: 0000000000000000
  RDX: ffffa0a280000000 RSI: 0000000000000000 RDI: ffffa0a4b3814000
  RBP: ffffc0bd4128ba38 R08: 0000000000001000 R09: ffffc0bd4128b948
  R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000240
  R13: ffffa0a4b556fb60 R14: ffffa0a4ab8f0af0 R15: ffffa0a4ab8f0af0
  FS: 0000000000000000(0000) GS:ffffa0a4b7a00000(0000) knlGS:0000000000000000
  CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 00007f2461c80020 CR3: 000000022b32a006 CR4: 00000000000206f0
  Call Trace:
  ? _cond_resched+0x1a/0x50
  push_leaf_left+0x179/0x190
  btrfs_del_items+0x316/0x470
  btrfs_del_csums+0x215/0x3a0
  __btrfs_free_extent.isra.72+0x5a7/0xbe0
  __btrfs_run_delayed_refs+0x539/0x1120
  btrfs_run_delayed_refs+0xdb/0x1b0
  btrfs_commit_transaction+0x52/0x950
  ? start_transaction+0x94/0x450
  transaction_kthread+0x163/0x190
  kthread+0x105/0x140
  ? btrfs_cleanup_transaction+0x560/0x560
  ? kthread_destroy_worker+0x50/0x50
  ret_from_fork+0x35/0x40
  Modules linked in:
  ---[ end trace c2425e6e89b5558f ]---

[CAUSE]
The offending csum tree looks like this:

checksum tree key (CSUM_TREE ROOT_ITEM 0)
node 29741056 level 1 items 14 free 107 generation 19 owner CSUM_TREE

	  ...
	  key (EXTENT_CSUM EXTENT_CSUM 85975040) block 29630464 gen 17
	  key (EXTENT_CSUM EXTENT_CSUM 89911296) block 29642752 gen 17 <<<
	  key (EXTENT_CSUM EXTENT_CSUM 92274688) block 29646848 gen 17
	  ...

leaf 29630464 items 6 free space 1 generation 17 owner CSUM_TREE

	  item 0 key (EXTENT_CSUM EXTENT_CSUM 85975040) itemoff 3987 itemsize 8
		  range start 85975040 end 85983232 length 8192
	  ...

leaf 29642752 items 0 free space 3995 generation 17 owner 0
^ empty leaf invalid owner ^

leaf 29646848 items 1 free space 602 generation 17 owner CSUM_TREE

	  item 0 key (EXTENT_CSUM EXTENT_CSUM 92274688) itemoff 627 itemsize 3368
		  range start 92274688 end 95723520 length 3448832

So we have a corrupted csum tree where one tree leaf is completely empty, causing unbalanced btree, thus leading to unexpected btree balance error.

[FIX]
For this particular case, we handle it in two directions to catch it:
- Check if the tree block is empty through btrfs_verify_level_key() So that invalid tree blocks won't be read out through btrfs_search_slot() and its variants.

- Check 0 tree owner in tree checker
NO tree is using 0 as its tree owner, detect it and reject at tree block read time.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202821

---
 fs/btrfs/disk-io.c      | 10 ++++++++++
 fs/btrfs/tree-checker.c |  6 ++++++
 2 files changed, 16 insertions(+)
fs/btrfs/disk-io.c +10 -0
index 97beb351a10cd..65af7eb3f7bd7 100644
@@ -416,6 +416,16 @@ int btrfs_verify_level_key(struct extent_buffer *eb, int level,
 	 */
 	if (btrfs_header_generation(eb) > fs_info->last_trans_committed)
 		return 0;
+
+	/* We have @first_key, so this @eb must have at least one item */
+	if (btrfs_header_nritems(eb) == 0) {
+		btrfs_err(fs_info,
+		"invalid tree nritems, bytenr=%llu nritems=0 expect >0",
+			  eb->start);
+		WARN_ON(IS_ENABLED(CONFIG_BTRFS_DEBUG));
+		return -EUCLEAN;
+	}
+
 	if (found_level)
 		btrfs_node_key_to_cpu(eb, &found_key, 0);
 	else
fs/btrfs/tree-checker.c +6 -0
index d83adda6c090a..9634cae1e1b1d 100644
@@ -991,6 +991,12 @@ static int check_leaf(struct extent_buffer *leaf, bool check_item_data)
 				    owner);
 			return -EUCLEAN;
 		}
+		/* Unknown tree */
+		if (owner == 0) {
+			generic_err(leaf, 0,
+				"invalid owner, root 0 is not defined");
+			return -EUCLEAN;
+		}
 		return 0;
 	}
 
Signature · 1 line
2.20.1
author maintainer
#104 lore raw

PATCH 97/203 powerpc/Makefile: Always pass --synthetic to nm if supported

In reply to Sasha Levin

From: Michael Ellerman <[email protected]>

[ Upstream commit 117acf5c29dd89e4c86761c365b9724dba0d9763 ]

Back in 2004 we added logic to arch/ppc64/Makefile to pass the --synthetic option to nm, if it was supported by nm.

Then in 2005 when arch/ppc64 and arch/ppc were merged, the logic to add --synthetic was moved inside an #ifdef CONFIG_PPC64 block within arch/powerpc/Makefile, and has remained there since.

That was fine, though crufty, until recently when a change to init/Kconfig added a config time check that uses $(NM). On powerpc that leads to an infinite loop because Kconfig uses $(NM) to calculate some values, then the powerpc Makefile changes $(NM), which Kconfig notices and restarts.

The original commit that added --synthetic simply said:
On new toolchains we need to use nm --synthetic or we miss code symbols.

And the nm man page says that the --synthetic option causes nm to:
Include synthetic symbols in the output. These are special symbols created by the linker for various purposes.

So it seems safe to always pass --synthetic if nm supports it, ie. on 32-bit and 64-bit, it just means 32-bit kernels might have more symbols reported (and in practice I see no extra symbols). Making it unconditional avoids the #ifdef CONFIG_PPC64, which in turn avoids the infinite loop.

---
 arch/powerpc/Makefile | 2 --
 1 file changed, 2 deletions(-)
arch/powerpc/Makefile +0 -2
index c345b79414a96..403f7e193833a 100644
@@ -39,13 +39,11 @@ endif
 uname := $(shell uname -m)
 KBUILD_DEFCONFIG := $(if $(filter ppc%,$(uname)),$(uname),ppc64)_defconfig
 
-ifdef CONFIG_PPC64
 new_nm := $(shell if $(NM) --help 2>&1 | grep -- '--synthetic' > /dev/null; then echo y; else echo n; fi)
 
 ifeq ($(new_nm),y)
 NM		:= $(NM) --synthetic
 endif
-endif
 
 # BITS is used as extension for files which are available in a 32 bit
 # and a 64 bit version to simplify shared Makefiles.
Signature · 1 line
2.20.1
author maintainer
#207 lore raw

PATCH 194/203 media: ttusb-dec: Fix info-leak in ttusb_dec_send_command()

In reply to Sasha Levin

From: Tomas Bortoli <[email protected]>

[ Upstream commit a10feaf8c464c3f9cfdd3a8a7ce17e1c0d498da1 ]

The function at issue does not always initialize each byte allocated for 'b' and can therefore leak uninitialized memory to a USB device in the call to usb_bulk_msg()

Use kzalloc() instead of kmalloc()

---
 drivers/media/usb/ttusb-dec/ttusb_dec.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/media/usb/ttusb-dec/ttusb_dec.c +1 -1
index 1d0afa340f47c..3198f9624b7c0 100644
@@ -319,7 +319,7 @@ static int ttusb_dec_send_command(struct ttusb_dec *dec, const u8 command,
 
 	dprintk("%s\n", __func__);
 
-	b = kmalloc(COMMAND_PACKET_SIZE + 4, GFP_KERNEL);
+	b = kzalloc(COMMAND_PACKET_SIZE + 4, GFP_KERNEL);
 	if (!b)
 		return -ENOMEM;
 
Signature · 1 line
2.20.1
author maintainer
#205 lore raw

PATCH 192/203 ALSA: hda - Drop unsol event handler for Intel HDMI codecs

In reply to Sasha Levin

From: Takashi Iwai <[email protected]>

[ Upstream commit f2dbe87c5ac1f88e6007ba1f1374f4bd8a197fb6 ]

We don't need to deal with the unsol events for Intel chips that are tied with the graphics via audio component notifier. Although the presence of the audio component is checked at the beginning of hdmi_unsol_event(), better to short cut by dropping unsol_event ops.

---
 sound/pci/hda/patch_hdmi.c | 9 ++++++++-
 1 file changed, 8 insertions(+), 1 deletion(-)
sound/pci/hda/patch_hdmi.c +8 -1
index c380596b2e84c..36240def9bf58 100644
@@ -2616,6 +2616,8 @@ static void i915_pin_cvt_fixup(struct hda_codec *codec,
 /* precondition and allocation for Intel codecs */
 static int alloc_intel_hdmi(struct hda_codec *codec)
 {
+	int err;
+
 	/* requires i915 binding */
 	if (!codec->bus->core.audio_component) {
 		codec_info(codec, "No i915 binding for Intel HDMI/DP codec\n");
@@ -2624,7 +2626,12 @@ static int alloc_intel_hdmi(struct hda_codec *codec)
 		return -ENODEV;
 	}
 
-	return alloc_generic_hdmi(codec);
+	err = alloc_generic_hdmi(codec);
+	if (err < 0)
+		return err;
+	/* no need to handle unsol events */
+	codec->patch_ops.unsol_event = NULL;
+	return 0;
 }
 
 /* parse and post-process for Intel codecs */
Signature · 1 line
2.20.1
author maintainer
#216 lore raw

PATCH 203/203 kvm: Nested KVM MMUs need PAE root too

In reply to Sasha Levin

From: Jiří Paleček <[email protected]>

[ Upstream commit 1cfff4d9a5d01fa61e5768a6afffc81ae1c8ecb9 ]

On AMD processors, in PAE 32bit mode, nested KVM instances don't work. The L0 host get a kernel OOPS, which is related to arch.mmu->pae_root being NULL.

The reason for this is that when setting up nested KVM instance, arch.mmu is set to &arch.guest_mmu (while normally, it would be &arch.root_mmu). However, the initialization and allocation of pae_root only creates it in root_mmu. KVM code (ie. in mmu_alloc_shadow_roots) then accesses arch.mmu->pae_root, which is the unallocated arch.guest_mmu->pae_root.

This fix just allocates (and frees) pae_root in both guest_mmu and root_mmu (and also lm_root if it was allocated). The allocation is subject to previous restrictions ie. it won't allocate anything on 64-bit and AFAIK not on Intel.

---
 arch/x86/kvm/mmu.c | 30 ++++++++++++++++++++++--------
 1 file changed, 22 insertions(+), 8 deletions(-)
arch/x86/kvm/mmu.c +22 -8
index a63964e7cec7b..c68bf3aab12c1 100644
@@ -5611,13 +5611,13 @@ slot_handle_leaf(struct kvm *kvm, struct kvm_memory_slot *memslot,
 				 PT_PAGE_TABLE_LEVEL, lock_flush_tlb);
 }
 
-static void free_mmu_pages(struct kvm_vcpu *vcpu)
+static void free_mmu_pages(struct kvm_mmu *mmu)
 {
-	free_page((unsigned long)vcpu->arch.mmu->pae_root);
-	free_page((unsigned long)vcpu->arch.mmu->lm_root);
+	free_page((unsigned long)mmu->pae_root);
+	free_page((unsigned long)mmu->lm_root);
 }
 
-static int alloc_mmu_pages(struct kvm_vcpu *vcpu)
+static int alloc_mmu_pages(struct kvm_vcpu *vcpu, struct kvm_mmu *mmu)
 {
 	struct page *page;
 	int i;
@@ -5638,9 +5638,9 @@ static int alloc_mmu_pages(struct kvm_vcpu *vcpu)
 	if (!page)
 		return -ENOMEM;
 
-	vcpu->arch.mmu->pae_root = page_address(page);
+	mmu->pae_root = page_address(page);
 	for (i = 0; i < 4; ++i)
-		vcpu->arch.mmu->pae_root[i] = INVALID_PAGE;
+		mmu->pae_root[i] = INVALID_PAGE;
 
 	return 0;
 }
@@ -5648,6 +5648,7 @@ static int alloc_mmu_pages(struct kvm_vcpu *vcpu)
 int kvm_mmu_create(struct kvm_vcpu *vcpu)
 {
 	uint i;
+	int ret;
 
 	vcpu->arch.mmu = &vcpu->arch.root_mmu;
 	vcpu->arch.walk_mmu = &vcpu->arch.root_mmu;
@@ -5665,7 +5666,19 @@ int kvm_mmu_create(struct kvm_vcpu *vcpu)
 		vcpu->arch.guest_mmu.prev_roots[i] = KVM_MMU_ROOT_INFO_INVALID;
 
 	vcpu->arch.nested_mmu.translate_gpa = translate_nested_gpa;
-	return alloc_mmu_pages(vcpu);
+
+	ret = alloc_mmu_pages(vcpu, &vcpu->arch.guest_mmu);
+	if (ret)
+		return ret;
+
+	ret = alloc_mmu_pages(vcpu, &vcpu->arch.root_mmu);
+	if (ret)
+		goto fail_allocate_root;
+
+	return ret;
+ fail_allocate_root:
+	free_mmu_pages(&vcpu->arch.guest_mmu);
+	return ret;
 }
 
 
@@ -6168,7 +6181,8 @@ unsigned long kvm_mmu_calculate_default_mmu_pages(struct kvm *kvm)
 void kvm_mmu_destroy(struct kvm_vcpu *vcpu)
 {
 	kvm_mmu_unload(vcpu);
-	free_mmu_pages(vcpu);
+	free_mmu_pages(&vcpu->arch.root_mmu);
+	free_mmu_pages(&vcpu->arch.guest_mmu);
 	mmu_free_memory_caches(vcpu);
 }
 
Signature · 1 line
2.20.1
author maintainer
#214 lore raw

PATCH 201/203 btrfs: tree-checker: Add ROOT_ITEM check

In reply to Sasha Levin

From: Qu Wenruo <[email protected]>

[ Upstream commit 259ee7754b6793af8bdd77f9ca818bc41cfe9541 ]

This patch will introduce ROOT_ITEM check, which includes:
- Key->objectid and key->offset check
Currently only some easy check, e.g. 0 as rootid is invalid.

- Item size check
Root item size is fixed.

- Generation checks
Generation, generation_v2 and last_snapshot should not be greater than super generation + 1

- Level and alignment check
Level should be in [0, 7], and bytenr must be aligned to sector size.

- Flags check

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=203261

---
 fs/btrfs/tree-checker.c | 92 +++++++++++++++++++++++++++++++++++++++++
 1 file changed, 92 insertions(+)
fs/btrfs/tree-checker.c +92 -0
index ccd5706199d76..d83adda6c090a 100644
@@ -821,6 +821,95 @@ static int check_inode_item(struct extent_buffer *leaf,
 	return 0;
 }
 
+static int check_root_item(struct extent_buffer *leaf, struct btrfs_key *key,
+			   int slot)
+{
+	struct btrfs_fs_info *fs_info = leaf->fs_info;
+	struct btrfs_root_item ri;
+	const u64 valid_root_flags = BTRFS_ROOT_SUBVOL_RDONLY |
+				     BTRFS_ROOT_SUBVOL_DEAD;
+
+	/* No such tree id */
+	if (key->objectid == 0) {
+		generic_err(leaf, slot, "invalid root id 0");
+		return -EUCLEAN;
+	}
+
+	/*
+	 * Some older kernel may create ROOT_ITEM with non-zero offset, so here
+	 * we only check offset for reloc tree whose key->offset must be a
+	 * valid tree.
+	 */
+	if (key->objectid == BTRFS_TREE_RELOC_OBJECTID && key->offset == 0) {
+		generic_err(leaf, slot, "invalid root id 0 for reloc tree");
+		return -EUCLEAN;
+	}
+
+	if (btrfs_item_size_nr(leaf, slot) != sizeof(ri)) {
+		generic_err(leaf, slot,
+			    "invalid root item size, have %u expect %zu",
+			    btrfs_item_size_nr(leaf, slot), sizeof(ri));
+	}
+
+	read_extent_buffer(leaf, &ri, btrfs_item_ptr_offset(leaf, slot),
+			   sizeof(ri));
+
+	/* Generation related */
+	if (btrfs_root_generation(&ri) >
+	    btrfs_super_generation(fs_info->super_copy) + 1) {
+		generic_err(leaf, slot,
+			"invalid root generation, have %llu expect (0, %llu]",
+			    btrfs_root_generation(&ri),
+			    btrfs_super_generation(fs_info->super_copy) + 1);
+		return -EUCLEAN;
+	}
+	if (btrfs_root_generation_v2(&ri) >
+	    btrfs_super_generation(fs_info->super_copy) + 1) {
+		generic_err(leaf, slot,
+		"invalid root v2 generation, have %llu expect (0, %llu]",
+			    btrfs_root_generation_v2(&ri),
+			    btrfs_super_generation(fs_info->super_copy) + 1);
+		return -EUCLEAN;
+	}
+	if (btrfs_root_last_snapshot(&ri) >
+	    btrfs_super_generation(fs_info->super_copy) + 1) {
+		generic_err(leaf, slot,
+		"invalid root last_snapshot, have %llu expect (0, %llu]",
+			    btrfs_root_last_snapshot(&ri),
+			    btrfs_super_generation(fs_info->super_copy) + 1);
+		return -EUCLEAN;
+	}
+
+	/* Alignment and level check */
+	if (!IS_ALIGNED(btrfs_root_bytenr(&ri), fs_info->sectorsize)) {
+		generic_err(leaf, slot,
+		"invalid root bytenr, have %llu expect to be aligned to %u",
+			    btrfs_root_bytenr(&ri), fs_info->sectorsize);
+		return -EUCLEAN;
+	}
+	if (btrfs_root_level(&ri) >= BTRFS_MAX_LEVEL) {
+		generic_err(leaf, slot,
+			    "invalid root level, have %u expect [0, %u]",
+			    btrfs_root_level(&ri), BTRFS_MAX_LEVEL - 1);
+		return -EUCLEAN;
+	}
+	if (ri.drop_level >= BTRFS_MAX_LEVEL) {
+		generic_err(leaf, slot,
+			    "invalid root level, have %u expect [0, %u]",
+			    ri.drop_level, BTRFS_MAX_LEVEL - 1);
+		return -EUCLEAN;
+	}
+
+	/* Flags check */
+	if (btrfs_root_flags(&ri) & ~valid_root_flags) {
+		generic_err(leaf, slot,
+			    "invalid root flags, have 0x%llx expect mask 0x%llx",
+			    btrfs_root_flags(&ri), valid_root_flags);
+		return -EUCLEAN;
+	}
+	return 0;
+}
+
 /*
  * Common point to switch the item-specific validation.
  */
@@ -856,6 +945,9 @@ static int check_leaf_item(struct extent_buffer *leaf,
 	case BTRFS_INODE_ITEM_KEY:
 		ret = check_inode_item(leaf, key, slot);
 		break;
+	case BTRFS_ROOT_ITEM_KEY:
+		ret = check_root_item(leaf, key, slot);
+		break;
 	}
 	return ret;
 }
Signature · 1 line
2.20.1
author maintainer
#213 lore raw

PATCH 200/203 btrfs: extent-tree: Make sure we only allocate extents from block groups with the same type

In reply to Sasha Levin

From: Qu Wenruo <[email protected]>

[ Upstream commit 2a28468e525f3924efed7f29f2bc5a2926e7e19a ]

[BUG]
With fuzzed image and MIXED_GROUPS super flag, we can hit the following BUG_ON():

kernel BUG at fs/btrfs/delayed-ref.c:491!
invalid opcode: 0000 [#1] PREEMPT SMP NOPTI

  CPU: 0 PID: 1849 Comm: sync Tainted: G           O      5.2.0-custom #27
  RIP: 0010:update_existing_head_ref.cold+0x44/0x46 [btrfs]
  Call Trace:
   add_delayed_ref_head+0x20c/0x2d0 [btrfs]
   btrfs_add_delayed_tree_ref+0x1fc/0x490 [btrfs]
   btrfs_free_tree_block+0x123/0x380 [btrfs]
   __btrfs_cow_block+0x435/0x500 [btrfs]
   btrfs_cow_block+0x110/0x240 [btrfs]
   btrfs_search_slot+0x230/0xa00 [btrfs]
   ? __lock_acquire+0x105e/0x1e20
   btrfs_insert_empty_items+0x67/0xc0 [btrfs]
   alloc_reserved_file_extent+0x9e/0x340 [btrfs]
   __btrfs_run_delayed_refs+0x78e/0x1240 [btrfs]
   ? kvm_clock_read+0x18/0x30
   ? __sched_clock_gtod_offset+0x21/0x50
   btrfs_run_delayed_refs.part.0+0x4e/0x180 [btrfs]
   btrfs_run_delayed_refs+0x23/0x30 [btrfs]
   btrfs_commit_transaction+0x53/0x9f0 [btrfs]
   btrfs_sync_fs+0x7c/0x1c0 [btrfs]
   ? __ia32_sys_fdatasync+0x20/0x20
   sync_fs_one_sb+0x23/0x30
   iterate_supers+0x95/0x100
   ksys_sync+0x62/0xb0
   __ia32_sys_sync+0xe/0x20
   do_syscall_64+0x65/0x240
   entry_SYSCALL_64_after_hwframe+0x49/0xbe

[CAUSE]
This situation is caused by several factors:
- Fuzzed image
The extent tree of this fs missed one backref for extent tree root. So we can allocated space from that slot.

- MIXED_BG feature
Super block has MIXED_BG flag.

- No mixed block groups exists
All block groups are just regular ones.

This makes data space_info->block_groups[] contains metadata block groups. And when we reserve space for data, we can use space in metadata block group.

Then we hit the following file operations:

- fallocate
We need to allocate data extents.
find_free_extent() choose to use the metadata block to allocate space from, and choose the space of extent tree root, since its backref is missing.

This generate one delayed ref head with is_data = 1.

- extent tree update
We need to update extent tree at run_delayed_ref time.

This generate one delayed ref head with is_data = 0, for the same bytenr of old extent tree root.

Then we trigger the BUG_ON().

[FIX]
The quick fix here is to check block_group->flags before using it.

The problem can only happen for MIXED_GROUPS fs. Regular filesystems won't have space_info with DATA|METADATA flag, and no way to hit the bug.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=203255

---
 fs/btrfs/extent-tree.c | 8 ++++++++
 1 file changed, 8 insertions(+)
fs/btrfs/extent-tree.c +8 -0
index 8b7eb22d508a5..ef2f80825c826 100644
@@ -5751,6 +5751,14 @@ static noinline int find_free_extent(struct btrfs_fs_info *fs_info,
 			 */
 			if ((flags & extra) && !(block_group->flags & extra))
 				goto loop;
+
+			/*
+			 * This block group has different flags than we want.
+			 * It's possible that we have MIXED_GROUP flag but no
+			 * block group is mixed.  Just skip such block group.
+			 */
+			btrfs_release_block_group(block_group, delalloc);
+			continue;
 		}
 
 have_block_group:
Signature · 1 line
2.20.1
author maintainer
#212 lore raw

PATCH 199/203 btrfs: delayed-inode: Kill the BUG_ON() in btrfs_delete_delayed_dir_index()

In reply to Sasha Levin

From: Qu Wenruo <[email protected]>

[ Upstream commit 933c22a7512c5c09b1fdc46b557384efe8d03233 ]

There is one report of fuzzed image which leads to BUG_ON() in btrfs_delete_delayed_dir_index().

Although that fuzzed image can already be addressed by enhanced extent-tree error handler, it's still better to hunt down more BUG_ON().

This patch will hunt down two BUG_ON()s in btrfs_delete_delayed_dir_index():
- One for error from btrfs_delayed_item_reserve_metadata() Instead of BUG_ON(), we output an error message and free the item. And return the error.
All callers of this function handles the error by aborting current trasaction.

- One for possible EEXIST from __btrfs_add_delayed_deletion_item() That function can return -EEXIST.
We already have a good enough error message for that, only need to clean up the reserved metadata space and allocated item.

To help above cleanup, also modifiy __btrfs_remove_delayed_item() called in btrfs_release_delayed_item(), to skip unassociated item.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=203253

---
 fs/btrfs/delayed-inode.c | 13 +++++++++++--
 1 file changed, 11 insertions(+), 2 deletions(-)
fs/btrfs/delayed-inode.c +11 -2
index 43fdb2992956a..6858a05606dd3 100644
@@ -474,6 +474,9 @@ static void __btrfs_remove_delayed_item(struct btrfs_delayed_item *delayed_item)
 	struct rb_root_cached *root;
 	struct btrfs_delayed_root *delayed_root;
 
+	/* Not associated with any delayed_node */
+	if (!delayed_item->delayed_node)
+		return;
 	delayed_root = delayed_item->delayed_node->root->fs_info->delayed_root;
 
 	BUG_ON(!delayed_root);
@@ -1525,7 +1528,12 @@ int btrfs_delete_delayed_dir_index(struct btrfs_trans_handle *trans,
 	 * we have reserved enough space when we start a new transaction,
 	 * so reserving metadata failure is impossible.
 	 */
-	BUG_ON(ret);
+	if (ret < 0) {
+		btrfs_err(trans->fs_info,
+"metadata reservation failed for delayed dir item deltiona, should have been reserved");
+		btrfs_release_delayed_item(item);
+		goto end;
+	}
 
 	mutex_lock(&node->mutex);
 	ret = __btrfs_add_delayed_deletion_item(node, item);
@@ -1534,7 +1542,8 @@ int btrfs_delete_delayed_dir_index(struct btrfs_trans_handle *trans,
 			  "err add delayed dir index item(index: %llu) into the deletion tree of the delayed node(root id: %llu, inode id: %llu, errno: %d)",
 			  index, node->root->root_key.objectid,
 			  node->inode_id, ret);
-		BUG();
+		btrfs_delayed_item_release_metadata(dir->root, item);
+		btrfs_release_delayed_item(item);
 	}
 	mutex_unlock(&node->mutex);
 end:
Signature · 1 line
2.20.1
author maintainer
#211 lore raw

PATCH 198/203 zd1211rw: remove false assertion from zd_mac_clear()

In reply to Sasha Levin

From: Oliver Neukum <[email protected]>

[ Upstream commit 7a2eb7367fdea72e448d1a847aa857f6caf8ea2f ]

The function is called before the lock which is asserted was ever used. Just remove it.

---
 drivers/net/wireless/zydas/zd1211rw/zd_mac.c | 1 -
 1 file changed, 1 deletion(-)
drivers/net/wireless/zydas/zd1211rw/zd_mac.c +0 -1
index da7e63fca9f57..a9999d10ae81f 100644
@@ -223,7 +223,6 @@ void zd_mac_clear(struct zd_mac *mac)
 {
 	flush_workqueue(zd_workqueue);
 	zd_chip_clear(&mac->chip);
-	lockdep_assert_held(&mac->lock);
 	ZD_MEMCLEAR(mac, sizeof(struct zd_mac));
 }
 
Signature · 1 line
2.20.1
author maintainer
#204 lore raw

PATCH 191/203 ALSA: hda - Add a quirk model for fixing Huawei Matebook X right speaker

In reply to Sasha Levin

From: Tomas Espeleta <[email protected]>

[ Upstream commit a2ef03fe617a8365fb7794531b11ba587509a9b9 ]

[ This is rather a revival of the patch Tomas sent in months ago, but
applying only with the quirk model option -- tiwai ]

Hard coded coefficients to make Huawuei Matebook X right speaker work. The Matebook X has a ALC298, please refer to bug 197801 on how these numbers were reverse engineered from the Windows driver

The reversed engineered sequence represents a repeating pattern of verbs, and the only values that are changing periodically are written on indexes 0x23 and 0x25:

0x500, 0x23
0x400, VALUE1
0x500, 0x25
0x400, VALUE2

* skipped reading sequences (0x500 - 0xc00 sequences are ignored)
* static values from reverse engineering are used

NOTE: since a significant risk is still considered, this is provided as an experimental fix that isn't applied as default for now. For enabling the fix, you'll have to choose huawei-mbx-stereo via model option of snd-hda-intel module.

If we get feedback from users that this works stably, we may apply it per default.

[ Some coding style fixes and replacement with AC_VERB_* by tiwai ]

---
 Documentation/sound/hd-audio/models.rst |  3 +
 sound/pci/hda/patch_realtek.c           | 74 +++++++++++++++++++++++++
 2 files changed, 77 insertions(+)
Documentation/sound/hd-audio/models.rst +3 -0
index 7d7c191102a73..11298f0ce44db 100644
@@ -260,6 +260,9 @@ alc295-hp-x360
     HP Spectre X360 fixups
 alc-sense-combo
     Headset button support for Chrome platform
+huawei-mbx-stereo
+    Enable initialization verbs for Huawei MBX stereo speakers;
+    might be risky, try this at your own risk
 
 ALC66x/67x/892
 ==============
sound/pci/hda/patch_realtek.c +74 -0

98 lines not on this page · raw message

Signature · 1 line
2.20.1
author maintainer
#202 lore raw

PATCH 189/203 libertas: Add missing sentinel at end of if_usb.c fw_table

In reply to Sasha Levin

From: Kevin Easton <[email protected]>

[ Upstream commit 764f3f1ecffc434096e0a2b02f1a6cc964a89df6 ]

This sentinel tells the firmware loading process when to stop.

---
 drivers/net/wireless/marvell/libertas/if_usb.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/net/wireless/marvell/libertas/if_usb.c +2 -1
index afac2481909b6..20436a289d5cd 100644
@@ -50,7 +50,8 @@ static const struct lbs_fw_table fw_table[] = {
 	{ MODEL_8388, "libertas/usb8388_v5.bin", NULL },
 	{ MODEL_8388, "libertas/usb8388.bin", NULL },
 	{ MODEL_8388, "usb8388.bin", NULL },
-	{ MODEL_8682, "libertas/usb8682.bin", NULL }
+	{ MODEL_8682, "libertas/usb8682.bin", NULL },
+	{ 0, NULL, NULL }
 };
 
 static const struct usb_device_id if_usb_table[] = {
Signature · 1 line
2.20.1
author maintainer
#192 lore raw

PATCH 179/203 block: make rq sector size accessible for block stats

In reply to Sasha Levin

From: Hou Tao <[email protected]>

[ Upstream commit 3d24430694077313c75c6b89f618db09943621e4 ]

Currently rq->data_len will be decreased by partial completion or zeroed by completion, so when blk_stat_add() is invoked, data_len will be zero and there will never be samples in poll_cb because blk_mq_poll_stats_bkt() will return -1 if data_len is zero.

We could move blk_stat_add() back to __blk_mq_complete_request(), but that would make the effort of trying to call ktime_get_ns() once in vain. Instead we can reuse throtl_size field, and use it for both block stats and block throttle, and adjust the logic in blk_mq_poll_stats_bkt() accordingly.

Fixes 4bc6339a583c ("block: move blk_stat_add() to __blk_mq_end_request()")
---
 block/blk-mq.c         | 11 +++++------
 block/blk-throttle.c   |  3 ++-
 include/linux/blkdev.h | 15 ++++++++++++---
 3 files changed, 19 insertions(+), 10 deletions(-)
block/blk-mq.c +5 -6
index a38ebb2a380c2..9b56428cad0e7 100644
@@ -44,12 +44,12 @@ static void blk_mq_poll_stats_fn(struct blk_stat_callback *cb);
 
 static int blk_mq_poll_stats_bkt(const struct request *rq)
 {
-	int ddir, bytes, bucket;
+	int ddir, sectors, bucket;
 
 	ddir = rq_data_dir(rq);
-	bytes = blk_rq_bytes(rq);
+	sectors = blk_rq_stats_sectors(rq);
 
-	bucket = ddir + 2*(ilog2(bytes) - 9);
+	bucket = ddir + 2 * ilog2(sectors);
 
 	if (bucket < 0)
 		return -1;
@@ -330,6 +330,7 @@ static struct request *blk_mq_rq_ctx_init(struct blk_mq_alloc_data *data,
 	else
 		rq->start_time_ns = 0;
 	rq->io_start_time_ns = 0;
+	rq->stats_sectors = 0;
 	rq->nr_phys_segments = 0;
 #if defined(CONFIG_BLK_DEV_INTEGRITY)
 	rq->nr_integrity_segments = 0;
@@ -673,9 +674,7 @@ void blk_mq_start_request(struct request *rq)
 
 	if (test_bit(QUEUE_FLAG_STATS, &q->queue_flags)) {
 		rq->io_start_time_ns = ktime_get_ns();
-#ifdef CONFIG_BLK_DEV_THROTTLING_LOW
-		rq->throtl_size = blk_rq_sectors(rq);
-#endif
+		rq->stats_sectors = blk_rq_sectors(rq);
 		rq->rq_flags |= RQF_STATS;
 		rq_qos_issue(q, rq);
 	}
block/blk-throttle.c +2 -1
index 8ab6c81532236..ee74bffe3504d 100644
@@ -2246,7 +2246,8 @@ void blk_throtl_stat_add(struct request *rq, u64 time_ns)
 	struct request_queue *q = rq->q;
 	struct throtl_data *td = q->td;
 
-	throtl_track_latency(td, rq->throtl_size, req_op(rq), time_ns >> 10);
+	throtl_track_latency(td, blk_rq_stats_sectors(rq), req_op(rq),
+			     time_ns >> 10);
 }
 
 void blk_throtl_bio_endio(struct bio *bio)
include/linux/blkdev.h +12 -3
index 1ef375dafb1c1..ae51050c50949 100644
@@ -202,9 +202,12 @@ struct request {
 #ifdef CONFIG_BLK_WBT
 	unsigned short wbt_flags;
 #endif
-#ifdef CONFIG_BLK_DEV_THROTTLING_LOW
-	unsigned short throtl_size;
-#endif
+	/*
+	 * rq sectors used for blk stats. It has the same value
+	 * with blk_rq_sectors(rq), except that it never be zeroed
+	 * by completion.
+	 */
+	unsigned short stats_sectors;
 
 	/*
 	 * Number of scatter-gather DMA addr+len pairs after
@@ -903,6 +906,7 @@ static inline struct request_queue *bdev_get_queue(struct block_device *bdev)
  * blk_rq_err_bytes()		: bytes left till the next error boundary
  * blk_rq_sectors()		: sectors left in the entire request
  * blk_rq_cur_sectors()		: sectors left in the current segment
+ * blk_rq_stats_sectors()	: sectors of the entire request used for stats
  */
 static inline sector_t blk_rq_pos(const struct request *rq)
 {
@@ -931,6 +935,11 @@ static inline unsigned int blk_rq_cur_sectors(const struct request *rq)
 	return blk_rq_cur_bytes(rq) >> SECTOR_SHIFT;
 }
 
+static inline unsigned int blk_rq_stats_sectors(const struct request *rq)
+{
+	return rq->stats_sectors;
+}
+
 #ifdef CONFIG_BLK_DEV_ZONED
 static inline unsigned int blk_rq_zone_no(struct request *rq)
 {
Signature · 1 line
2.20.1
author maintainer
#191 lore raw

PATCH 178/203 io_uring: fix wrong sequence setting logic

In reply to Sasha Levin

From: Jackie Liu <[email protected]>

[ Upstream commit 8776f3fa15a5cd213c4dfab7ddaf557983374ea6 ]

Sqo_thread will get sqring in batches, which will cause ctx->cached_sq_head to be added in batches. if one of these sqes is set with the DRAIN flag, then he will never get a chance to process, and finally sqo_thread will not exit.

Fixes de0617e4671 ("io_uring: add support for marking commands as draining")
---
 fs/io_uring.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
fs/io_uring.c +3 -1
index cfb48bd088e12..06d048341fa41 100644
@@ -288,6 +288,7 @@ struct io_ring_ctx {
 struct sqe_submit {
 	const struct io_uring_sqe	*sqe;
 	unsigned short			index;
+	u32				sequence;
 	bool				has_user;
 	bool				needs_lock;
 	bool				needs_fixed_file;
@@ -2040,7 +2041,7 @@ static int io_req_set_file(struct io_ring_ctx *ctx, const struct sqe_submit *s,
 
 	if (flags & IOSQE_IO_DRAIN) {
 		req->flags |= REQ_F_IO_DRAIN;
-		req->sequence = ctx->cached_sq_head - 1;
+		req->sequence = s->sequence;
 	}
 
 	if (!io_op_needs_file(s->sqe))
@@ -2247,6 +2248,7 @@ static bool io_get_sqring(struct io_ring_ctx *ctx, struct sqe_submit *s)
 	if (head < ctx->sq_entries) {
 		s->index = head;
 		s->sqe = &ctx->sq_sqes[head];
+		s->sequence = ctx->cached_sq_head;
 		ctx->cached_sq_head++;
 		return true;
 	}
Signature · 1 line
2.20.1
author maintainer
#188 lore raw

PATCH 175/203 ASoC: dmaengine: Make the pcm->name equal to pcm->id if the name is not set

In reply to Sasha Levin

From: Peter Ujfalusi <[email protected]>

[ Upstream commit 2ec42f3147e1610716f184b02e65d7f493eed925 ]

Some tools use the snd_pcm_info_get_name() to try to identify PCMs or for other purposes.

Currently it is left empty with the dmaengine-pcm, in this case copy the pcm->id string as pcm->name.

For example IGT is using this to find the HDMI PCM for testing audio on it.

---
 sound/soc/soc-generic-dmaengine-pcm.c | 6 ++++++
 1 file changed, 6 insertions(+)
sound/soc/soc-generic-dmaengine-pcm.c +6 -0
index 748f5f641002e..d93db2c2b5270 100644
@@ -306,6 +306,12 @@ static int dmaengine_pcm_new(struct snd_soc_pcm_runtime *rtd)
 
 		if (!dmaengine_pcm_can_report_residue(dev, pcm->chan[i]))
 			pcm->flags |= SND_DMAENGINE_PCM_FLAG_NO_RESIDUE;
+
+		if (rtd->pcm->streams[i].pcm->name[0] == '\0') {
+			strncpy(rtd->pcm->streams[i].pcm->name,
+				rtd->pcm->streams[i].pcm->id,
+				sizeof(rtd->pcm->streams[i].pcm->name));
+		}
 	}
 
 	return 0;
Signature · 1 line
2.20.1
author maintainer
#187 lore raw

PATCH 174/203 SoC: simple-card-utils: set 0Hz to sysclk when shutdown

In reply to Sasha Levin

From: Katsuhiro Suzuki <[email protected]>

[ Upstream commit 2458adb8f92ad4d07ef7ab27c5bafa1d3f4678d6 ]

This patch set 0Hz to sysclk when shutdown the card.

Some codecs set rate constraints that derives from sysclk. This mechanism works correctly if machine drivers give fixed frequency.

But simple-audio and audio-graph card set variable clock rate if 'mclk-fs' property exists. In this case, rate constraints will go bad scenario. For example a codec accepts three limited rates (mclk / 256, mclk / 384, mclk / 512).

Bad scenario as follows (mclk-fs = 256):
- Initialize sysclk by correct value (Ex. 12.288MHz)
- Codec set constraints of PCM rate by sysclk 48kHz (1/256), 32kHz (1/384), 24kHz (1/512)
- Play 48kHz sound, it's acceptable
- Sysclk is not changed

- Play 32kHz sound, it's acceptable
- Set sysclk to 8.192MHz (= fs * mclk-fs = 32k * 256)
- Codec set constraints of PCM rate by sysclk 32kHz (1/256), 21.33kHz (1/384), 16kHz (1/512)

- Play 48kHz again, but it's NOT acceptable because constraints do not allow 48kHz

So codecs treat 0Hz sysclk as signal of applying no constraints to avoid this problem.

---
 sound/soc/generic/simple-card-utils.c | 7 +++++++
 1 file changed, 7 insertions(+)
sound/soc/generic/simple-card-utils.c +7 -0
index 556b1a789629d..9b794775df537 100644
@@ -213,10 +213,17 @@ EXPORT_SYMBOL_GPL(asoc_simple_startup);
 void asoc_simple_shutdown(struct snd_pcm_substream *substream)
 {
 	struct snd_soc_pcm_runtime *rtd = substream->private_data;
+	struct snd_soc_dai *codec_dai = rtd->codec_dai;
+	struct snd_soc_dai *cpu_dai = rtd->cpu_dai;
 	struct asoc_simple_priv *priv = snd_soc_card_get_drvdata(rtd->card);
 	struct simple_dai_props *dai_props =
 		simple_priv_to_props(priv, rtd->num);
 
+	if (dai_props->mclk_fs) {
+		snd_soc_dai_set_sysclk(codec_dai, 0, 0, SND_SOC_CLOCK_IN);
+		snd_soc_dai_set_sysclk(cpu_dai, 0, 0, SND_SOC_CLOCK_OUT);
+	}
+
 	asoc_simple_clk_disable(dai_props->cpu_dai);
 
 	asoc_simple_clk_disable(dai_props->codec_dai);
Signature · 1 line
2.20.1
author maintainer
#175 lore raw

PATCH 168/203 irqchip/gic-v3-its: Fix LPI release for Multi-MSI devices

In reply to Sasha Levin

From: Marc Zyngier <[email protected]>

[ Upstream commit c9c96e30ecaa0aafa225aa1a5392cb7db17c7a82 ]

When allocating a range of LPIs for a Multi-MSI capable device, this allocation extended to the closest power of 2.

But on the release path, the interrupts are released one by one. This results in not releasing the "extra" range, leaking the its_device. Trying to reprobe the device will then fail.

Fix it by releasing the LPIs the same way we allocate them.

Fixes 8208d1708b88 ("irqchip/gic-v3-its: Align PCI Multi-MSI allocation on their size")
---
 drivers/irqchip/irq-gic-v3-its.c | 9 ++++-----
 1 file changed, 4 insertions(+), 5 deletions(-)
drivers/irqchip/irq-gic-v3-its.c +4 -5
index 1b5c3672aea27..c3a8d732805f5 100644
@@ -2641,14 +2641,13 @@ static void its_irq_domain_free(struct irq_domain *domain, unsigned int virq,
 	struct its_node *its = its_dev->its;
 	int i;
 
+	bitmap_release_region(its_dev->event_map.lpi_map,
+			      its_get_event_id(irq_domain_get_irq_data(domain, virq)),
+			      get_count_order(nr_irqs));
+
 	for (i = 0; i < nr_irqs; i++) {
 		struct irq_data *data = irq_domain_get_irq_data(domain,
 								virq + i);
-		u32 event = its_get_event_id(data);
-
-		/* Mark interrupt index as unused */
-		clear_bit(event, its_dev->event_map.lpi_map);
-
 		/* Nuke the entry in the domain */
 		irq_domain_reset_irq_data(data);
 	}
Signature · 1 line
2.20.1
author maintainer
#165 lore raw

PATCH 158/203 ACPI / PCI: fix acpi_pci_irq_enable() memory leak

In reply to Sasha Levin

From: Wenwen Wang <[email protected]>

[ Upstream commit 29b49958cf73b439b17fa29e9a25210809a6c01c ]

In acpi_pci_irq_enable(), 'entry' is allocated by kzalloc() in acpi_pci_irq_check_entry() (invoked from acpi_pci_irq_lookup()). However, it is not deallocated if acpi_pci_irq_valid() returns false, leading to a memory leak. To fix this issue, free 'entry' before returning 0.

Fixes e237a5518425 ("x86/ACPI/PCI: Recognize that Interrupt Line 255 means "not connected"")
---
 drivers/acpi/pci_irq.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/acpi/pci_irq.c +3 -1
index d2549ae65e1b6..dea8a60e18a4c 100644
@@ -449,8 +449,10 @@ int acpi_pci_irq_enable(struct pci_dev *dev)
 		 * No IRQ known to the ACPI subsystem - maybe the BIOS /
 		 * driver reported one, then use it. Exit in any case.
 		 */
-		if (!acpi_pci_irq_valid(dev, pin))
+		if (!acpi_pci_irq_valid(dev, pin)) {
+			kfree(entry);
 			return 0;
+		}
 
 		if (acpi_isa_register_gsi(dev))
 			dev_warn(&dev->dev, "PCI INT %c: no GSI\n",
Signature · 1 line
2.20.1
author maintainer
#163 lore raw

PATCH 156/203 x86/amd_nb: Add PCI device IDs for family 17h, model 70h

In reply to Sasha Levin

From: Marcel Bocu <[email protected]>

[ Upstream commit af4e1c5eca95bed1192d8dc45c8ed63aea2209e8 ]

The AMD Ryzen gen 3 processors came with a different PCI IDs for the function 3 & 4 which are used to access the SMN interface. The root PCI address however remained at the same address as the model 30h.

Adding the F3/F4 PCI IDs respectively to the misc and link ids appear to be sufficient for k10temp, so let's add them and follow up on the patch if other functions need more tweaking.

Vicki Pfau sent an identical patch after I checked that no-one had written this patch. I would have been happy about dropping my patch but unlike for his patch series, I had already Cc:ed the x86 people and they already reviewed the changes. Since Vicki has not answered to any email after his initial series, let's assume she is on vacation and let's avoid duplication of reviews from the maintainers and merge my series. To acknowledge Vicki's anteriority, I added her S-o-b to the patch.

v2, suggested by Guenter Roeck and Brian Woods:
- rename from 71h to 70h

---
 arch/x86/kernel/amd_nb.c | 3 +++
 include/linux/pci_ids.h  | 1 +
 2 files changed, 4 insertions(+)
arch/x86/kernel/amd_nb.c +3 -0
index d63e63b7d1d95..251c795b4eb3c 100644
@@ -21,6 +21,7 @@
 #define PCI_DEVICE_ID_AMD_17H_DF_F4	0x1464
 #define PCI_DEVICE_ID_AMD_17H_M10H_DF_F4 0x15ec
 #define PCI_DEVICE_ID_AMD_17H_M30H_DF_F4 0x1494
+#define PCI_DEVICE_ID_AMD_17H_M70H_DF_F4 0x1444
 
 /* Protect the PCI config register pairs used for SMN and DF indirect access. */
 static DEFINE_MUTEX(smn_mutex);
@@ -50,6 +51,7 @@ const struct pci_device_id amd_nb_misc_ids[] = {
 	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_17H_M10H_DF_F3) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_17H_M30H_DF_F3) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CNB17H_F3) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_17H_M70H_DF_F3) },
 	{}
 };
 EXPORT_SYMBOL_GPL(amd_nb_misc_ids);
@@ -63,6 +65,7 @@ static const struct pci_device_id amd_nb_link_ids[] = {
 	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_17H_DF_F4) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_17H_M10H_DF_F4) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_17H_M30H_DF_F4) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_17H_M70H_DF_F4) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CNB17H_F4) },
 	{}
 };
include/linux/pci_ids.h +1 -0
index c842735a4f45a..4b97f427cc929 100644
@@ -548,6 +548,7 @@
 #define PCI_DEVICE_ID_AMD_17H_DF_F3	0x1463
 #define PCI_DEVICE_ID_AMD_17H_M10H_DF_F3 0x15eb
 #define PCI_DEVICE_ID_AMD_17H_M30H_DF_F3 0x1493
+#define PCI_DEVICE_ID_AMD_17H_M70H_DF_F3 0x1443
 #define PCI_DEVICE_ID_AMD_CNB17H_F3	0x1703
 #define PCI_DEVICE_ID_AMD_LANCE		0x2000
 #define PCI_DEVICE_ID_AMD_LANCE_HOME	0x2001
Signature · 1 line
2.20.1
author maintainer
#154 lore raw

PATCH 147/203 ALSA: firewire-motu: add support for MOTU 4pre

In reply to Sasha Levin

From: Takashi Sakamoto <[email protected]>

[ Upstream commit 6af86bdb8ad41f4cf1292d3b10857dc322758328 ]

MOTU 4pre was launched in 2012 by MOTU, Inc. This commit allows userspace applications can transmit and receive PCM frames and MIDI messages for this model via ALSA PCM interface and RawMidi/Sequencer interfaces.

The device supports MOTU protocol version 3. Unlike the other devices, the device is simply designed. The size of data block is fixed to 10 quadlets during available sampling rates (44.1 - 96.0 kHz). Each data block includes 1 source packet header, 2 data chunks for messages, 8 data chunks for PCM samples and 2 data chunks for padding to quadlet alignment. The device has no MIDI, optical, BNC and AES/EBU interfaces.

Like support for the other MOTU devices, the quality of playback sound is not enough good with periodical noise yet.

$ python2 crpp < ~/git/am-config-rom/motu/motu-4pre.img
               ROM header and bus information block
               -----------------------------------------------------------------
400  041078cc  bus_info_length 4, crc_length 16, crc 30924
404  31333934  bus_name "1394"
408  20ff7000  irmc 0, cmc 0, isc 1, bmc 0, cyc_clk_acc 255, max_rec 7 (256)
40c  0001f200  company_id 0001f2     |
410  000a41c5  device_id 00000a41c5  | EUI-64 0001f200000a41c5
               root directory
               -----------------------------------------------------------------
414  0004ef04  directory_length 4, crc 61188
418  030001f2  vendor
41c  0c0083c0  node capabilities per IEEE 1394
420  d1000002  --> unit directory at 428
424  8d000005  --> eui-64 leaf at 438

unit directory at 428
-----------------------------------------------------------------

428  0003ceda  directory_length 3, crc 52954
42c  120001f2  specifier id
430  13000045  version
434  17103800  model
               eui-64 leaf at 438
               -----------------------------------------------------------------
438  0002d248  leaf_length 2, crc 53832
43c  0001f200  company_id 0001f2     |
440  000a41c5  device_id 00000a41c5  | EUI-64 0001f200000a41c5
---
 sound/firewire/motu/motu.c | 12 ++++++++++++
 1 file changed, 12 insertions(+)
sound/firewire/motu/motu.c +12 -0
index 03cda2166ea3d..72908b4de77c0 100644
@@ -247,6 +247,17 @@ static const struct snd_motu_spec motu_audio_express = {
 	.analog_out_ports = 4,
 };
 
+static const struct snd_motu_spec motu_4pre = {
+	.name = "4pre",
+	.protocol = &snd_motu_protocol_v3,
+	.flags = SND_MOTU_SPEC_SUPPORT_CLOCK_X2 |
+		 SND_MOTU_SPEC_TX_MICINST_CHUNK |
+		 SND_MOTU_SPEC_TX_RETURN_CHUNK |
+		 SND_MOTU_SPEC_RX_SEPARETED_MAIN,
+	.analog_in_ports = 2,
+	.analog_out_ports = 2,
+};
+
 #define SND_MOTU_DEV_ENTRY(model, data)			\
 {							\
 	.match_flags	= IEEE1394_MATCH_VENDOR_ID |	\
@@ -265,6 +276,7 @@ static const struct ieee1394_device_id motu_id_table[] = {
 	SND_MOTU_DEV_ENTRY(0x000015, &motu_828mk3),	/* FireWire only. */
 	SND_MOTU_DEV_ENTRY(0x000035, &motu_828mk3),	/* Hybrid. */
 	SND_MOTU_DEV_ENTRY(0x000033, &motu_audio_express),
+	SND_MOTU_DEV_ENTRY(0x000045, &motu_4pre),
 	{ }
 };
 MODULE_DEVICE_TABLE(ieee1394, motu_id_table);
Signature · 1 line
2.20.1
author maintainer
#151 lore raw

PATCH 144/203 x86/mm/pti: Handle unaligned address gracefully in pti_clone_pagetable()

In reply to Sasha Levin

From: Song Liu <[email protected]>

[ Upstream commit 825d0b73cd7526b0bb186798583fae810091cbac ]

pti_clone_pmds() assumes that the supplied address is either:

- properly PUD/PMD aligned
or
- the address is actually mapped which means that independently of the mapping level (PUD/PMD/PTE) the next higher mapping exists.

If that's not the case the unaligned address can be incremented by PUD or PMD size incorrectly. All callers supply mapped and/or aligned addresses, but for the sake of robustness it's better to handle that case properly and to emit a warning.

[ tglx: Rewrote changelog and added WARN_ON_ONCE() ]

---
 arch/x86/mm/pti.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
arch/x86/mm/pti.c +4 -2
index ba22b50f4eca2..7f2140414440d 100644
@@ -330,13 +330,15 @@ pti_clone_pgtable(unsigned long start, unsigned long end,
 
 		pud = pud_offset(p4d, addr);
 		if (pud_none(*pud)) {
-			addr += PUD_SIZE;
+			WARN_ON_ONCE(addr & ~PUD_MASK);
+			addr = round_up(addr + 1, PUD_SIZE);
 			continue;
 		}
 
 		pmd = pmd_offset(pud, addr);
 		if (pmd_none(*pmd)) {
-			addr += PMD_SIZE;
+			WARN_ON_ONCE(addr & ~PMD_MASK);
+			addr = round_up(addr + 1, PMD_SIZE);
 			continue;
 		}
 
Signature · 1 line
2.20.1
author maintainer
#149 lore raw

PATCH 142/203 x86/mm/pti: Do not invoke PTI functions when PTI is disabled

In reply to Sasha Levin

From: Thomas Gleixner <[email protected]>

[ Upstream commit 990784b57731192b7d90c8d4049e6318d81e887d ]

When PTI is disabled at boot time either because the CPU is not affected or PTI has been disabled on the command line, the boot code still calls into pti_finalize() which then unconditionally invokes:

pti_clone_entry_text()
pti_clone_kernel_text()

pti_clone_kernel_text() was called unconditionally before the 32bit support was added and 32bit added the call to pti_clone_entry_text().

The call has no side effects as cloning the page tables into the available second one, which was allocated for PTI does not create damage. But it does not make sense either and in case that this functionality would be extended later this might actually lead to hard to diagnose issues.

Neither function should be called when PTI is runtime disabled. Make the invocation conditional.

---
 arch/x86/mm/pti.c | 2 ++
 1 file changed, 2 insertions(+)
arch/x86/mm/pti.c +2 -0
index b196524759ec5..ba22b50f4eca2 100644
@@ -666,6 +666,8 @@ void __init pti_init(void)
  */
 void pti_finalize(void)
 {
+	if (!boot_cpu_has(X86_FEATURE_PTI))
+		return;
 	/*
 	 * We need to clone everything (again) that maps parts of the
 	 * kernel image.
Signature · 1 line
2.20.1
author maintainer
#141 lore raw

PATCH 134/203 ACPI / CPPC: do not require the _PSD method

In reply to Sasha Levin

From: Al Stone <[email protected]>

[ Upstream commit 4c4cdc4c63853fee48c02e25c8605fb65a6c9924 ]

According to the ACPI 6.3 specification, the _PSD method is optional when using CPPC. The underlying assumption is that each CPU can change frequency independently from all other CPUs; _PSD is provided to tell the OS that some processors can NOT do that.

However, the acpi_get_psd() function returns ENODEV if there is no _PSD method present, or an ACPI error status if an error occurs when evaluating _PSD, if present. This makes _PSD mandatory when using CPPC, in violation of the specification, and only on Linux.

This has forced some firmware writers to provide a dummy _PSD, even though it is irrelevant, but only because Linux requires it; other OSPMs follow the spec. We really do not want to have OS specific ACPI tables, though.

So, correct acpi_get_psd() so that it does not return an error if there is no _PSD method present, but does return a failure when the method can not be executed properly. This allows _PSD to be optional as it should be.

---
 drivers/acpi/cppc_acpi.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
drivers/acpi/cppc_acpi.c +4 -2
index 15f103d7532b0..3b2525908dd8c 100644
@@ -365,8 +365,10 @@ static int acpi_get_psd(struct cpc_desc *cpc_ptr, acpi_handle handle)
 	union acpi_object  *psd = NULL;
 	struct acpi_psd_package *pdomain;
 
-	status = acpi_evaluate_object_typed(handle, "_PSD", NULL, &buffer,
-			ACPI_TYPE_PACKAGE);
+	status = acpi_evaluate_object_typed(handle, "_PSD", NULL,
+					    &buffer, ACPI_TYPE_PACKAGE);
+	if (status == AE_NOT_FOUND)	/* _PSD is optional */
+		return 0;
 	if (ACPI_FAILURE(status))
 		return -ENODEV;
 
Signature · 1 line
2.20.1
author maintainer
#140 lore raw

PATCH 133/203 ASoC: es8316: fix headphone mixer volume table

In reply to Sasha Levin

From: Katsuhiro Suzuki <[email protected]>

[ Upstream commit f972d02fee2496024cfd6f59021c9d89d54922a6 ]

This patch fix setting table of Headphone mixer volume. Current code uses 4 ... 7 values but these values are prohibited.

Correct settings are the following:
0000 -12dB
0001 -10.5dB
0010 -9dB
0011 -7.5dB
0100 -6dB
1000 -4.5dB
1001 -3dB
1010 -1.5dB
1011 0dB

---
 sound/soc/codecs/es8316.c | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)
sound/soc/codecs/es8316.c +5 -2
index 6db002cc20582..96d04896193f2 100644
@@ -51,7 +51,10 @@ static const SNDRV_CTL_TLVD_DECLARE_DB_SCALE(adc_vol_tlv, -9600, 50, 1);
 static const SNDRV_CTL_TLVD_DECLARE_DB_SCALE(alc_max_gain_tlv, -650, 150, 0);
 static const SNDRV_CTL_TLVD_DECLARE_DB_SCALE(alc_min_gain_tlv, -1200, 150, 0);
 static const SNDRV_CTL_TLVD_DECLARE_DB_SCALE(alc_target_tlv, -1650, 150, 0);
-static const SNDRV_CTL_TLVD_DECLARE_DB_SCALE(hpmixer_gain_tlv, -1200, 150, 0);
+static const SNDRV_CTL_TLVD_DECLARE_DB_RANGE(hpmixer_gain_tlv,
+	0, 4, TLV_DB_SCALE_ITEM(-1200, 150, 0),
+	8, 11, TLV_DB_SCALE_ITEM(-450, 150, 0),
+);
 
 static const SNDRV_CTL_TLVD_DECLARE_DB_RANGE(adc_pga_gain_tlv,
 	0, 0, TLV_DB_SCALE_ITEM(-350, 0, 0),
@@ -89,7 +92,7 @@ static const struct snd_kcontrol_new es8316_snd_controls[] = {
 	SOC_DOUBLE_TLV("Headphone Playback Volume", ES8316_CPHP_ICAL_VOL,
 		       4, 0, 3, 1, hpout_vol_tlv),
 	SOC_DOUBLE_TLV("Headphone Mixer Volume", ES8316_HPMIX_VOL,
-		       0, 4, 7, 0, hpmixer_gain_tlv),
+		       0, 4, 11, 0, hpmixer_gain_tlv),
 
 	SOC_ENUM("Playback Polarity", dacpol),
 	SOC_DOUBLE_R_TLV("DAC Playback Volume", ES8316_DAC_VOLL,
Signature · 1 line
2.20.1
author maintainer
#138 lore raw

PATCH 131/203 media: ov9650: add a sanity check

In reply to Sasha Levin

From: Mauro Carvalho Chehab <[email protected]>

[ Upstream commit 093347abc7a4e0490e3c962ecbde2dc272a8f708 ]

As pointed by cppcheck:

[drivers/media/i2c/ov9650.c:706]: (error) Shifting by a negative value is undefined behaviour [drivers/media/i2c/ov9650.c:707]: (error) Shifting by a negative value is undefined behaviour [drivers/media/i2c/ov9650.c:721]: (error) Shifting by a negative value is undefined behaviour

Prevent mangling with gains with invalid values.

As pointed by Sylvester, this should never happen in practice, as min value of V4L2_CID_GAIN control is 16 (gain is always >= 16 and m is always >= 0), but it is too hard for a static analyzer to get this, as the logic with validates control min/max is elsewhere inside V4L2 core.

---
 drivers/media/i2c/ov9650.c | 5 +++++
 1 file changed, 5 insertions(+)
drivers/media/i2c/ov9650.c +5 -0
index 30ab2225fbd0c..b350f5c1a9890 100644
@@ -703,6 +703,11 @@ static int ov965x_set_gain(struct ov965x *ov965x, int auto_gain)
 		for (m = 6; m >= 0; m--)
 			if (gain >= (1 << m) * 16)
 				break;
+
+		/* Sanity check: don't adjust the gain with a negative value */
+		if (m < 0)
+			return -EINVAL;
+
 		rgain = (gain - ((1 << m) * 16)) / (1 << m);
 		rgain |= (((1 << m) - 1) << 4);
 
Signature · 1 line
2.20.1
author maintainer
#132 lore raw

PATCH 125/203 media: cpia2_usb: fix memory leaks

In reply to Sasha Levin

From: Wenwen Wang <[email protected]>

[ Upstream commit 1c770f0f52dca1a2323c594f01f5ec6f1dddc97f ]

In submit_urbs(), 'cam->sbuf[i].data' is allocated through kmalloc_array(). However, it is not deallocated if the following allocation for urbs fails. To fix this issue, free 'cam->sbuf[i].data' if usb_alloc_urb() fails.

---
 drivers/media/usb/cpia2/cpia2_usb.c | 4 ++++
 1 file changed, 4 insertions(+)
drivers/media/usb/cpia2/cpia2_usb.c +4 -0
index 17468f7d78ed2..3ab80a7b44985 100644
@@ -676,6 +676,10 @@ static int submit_urbs(struct camera_data *cam)
 		if (!urb) {
 			for (j = 0; j < i; j++)
 				usb_free_urb(cam->sbuf[j].urb);
+			for (j = 0; j < NUM_SBUF; j++) {
+				kfree(cam->sbuf[j].data);
+				cam->sbuf[j].data = NULL;
+			}
 			return -ENOMEM;
 		}
 
Signature · 1 line
2.20.1
author maintainer
#136 lore raw

PATCH 129/203 perf script: Fix memory leaks in list_scripts()

In reply to Sasha Levin

From: "Gustavo A. R. Silva" <[email protected]>

[ Upstream commit 3b4acbb92dbda4829e021e5c6d5410658849fa1c ]

In case memory resources for *buf* and *paths* were allocated, jump to *out* and release them before return.

Cc Alexander Shishkin <[email protected]>
Cc Andi Kleen <[email protected]>
Cc Gustavo A. R. Silva <[email protected]>
Cc Jiri Olsa <[email protected]>
Cc Namhyung Kim <[email protected]>
Cc Peter Zijlstra <[email protected]>

Addresses-Coverity-ID: 1444328 ("Resource leak")

Fixes 6f3da20e151f ("perf report: Support builtin perf script in scripts menu")
---
 tools/perf/ui/browsers/scripts.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
tools/perf/ui/browsers/scripts.c +4 -2
index 4d565cc14076c..0355d4aaf2eed 100644
@@ -131,8 +131,10 @@ static int list_scripts(char *script_name, bool *custom,
 		int key = ui_browser__input_window("perf script command",
 				"Enter perf script command line (without perf script prefix)",
 				script_args, "", 0);
-		if (key != K_ENTER)
-			return -1;
+		if (key != K_ENTER) {
+			ret = -1;
+			goto out;
+		}
 		sprintf(script_name, "%s script %s", perf, script_args);
 	} else if (choice < num + max_std) {
 		strcpy(script_name, paths[choice]);
Signature · 1 line
2.20.1
author maintainer
#134 lore raw

PATCH 127/203 perf trace beauty ioctl: Fix off-by-one error in cmd->string table

In reply to Sasha Levin

From: Benjamin Peterson <[email protected]>

[ Upstream commit b92675f4a9c02dd78052645597dac9e270679ddf ]

While tracing a program that calls isatty(3), I noticed that strace reported TCGETS for the request argument of the underlying ioctl(2) syscall while perf trace reported TCSETS. strace is corrrect. The bug in perf was due to the tty ioctl beauty table starting at 0x5400 rather than 0x5401.

Committer testing:

Using augmented_raw_syscalls.o and settings to make 'perf trace' use strace formatting, i.e. with this in ~/.perfconfig

  # cat ~/.perfconfig
  [trace]
	add_events = /home/acme/git/linux/tools/perf/examples/bpf/augmented_raw_syscalls.c
	show_zeros = yes
	show_duration = no
	no_inherit = yes
	show_timestamp = no
	show_arg_names = no
	args_alignment = 40
	show_prefix = yes
  # strace -e ioctl stty > /dev/null
  ioctl(0, TCGETS, {B38400 opost isig icanon echo ...}) = 0
  ioctl(1, TIOCGWINSZ, 0x7fff8a9b0860)    = -1 ENOTTY (Inappropriate ioctl for device)
  ioctl(1, TCGETS, 0x7fff8a9b0540)        = -1 ENOTTY (Inappropriate ioctl for device)
  +++ exited with 0 +++
  #

Before:

  # perf trace -e ioctl stty > /dev/null
  ioctl(0, TCSETS, 0x7fff2cf79f20)        = 0
  ioctl(1, TIOCSWINSZ, 0x7fff2cf79f40)    = -1 ENOTTY (Inappropriate ioctl for device)
  ioctl(1, TCSETS, 0x7fff2cf79c20)        = -1 ENOTTY (Inappropriate ioctl for device)
  #

After:

  # perf trace -e ioctl stty > /dev/null
  ioctl(0, TCGETS, 0x7ffed0763920)        = 0
  ioctl(1, TIOCGWINSZ, 0x7ffed0763940)    = -1 ENOTTY (Inappropriate ioctl for device)
  ioctl(1, TCGETS, 0x7ffed0763620)        = -1 ENOTTY (Inappropriate ioctl for device)
  #
Cc Alexander Shishkin <[email protected]>
Cc Jiri Olsa <[email protected]>
Cc Namhyung Kim <[email protected]>
Cc Peter Zijlstra <[email protected]>
Fixes 1cc47f2d46206d67285aea0ca7e8450af571da13 ("perf trace beauty ioctl: Improve 'cmd' beautifier")
---
 tools/perf/trace/beauty/ioctl.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
tools/perf/trace/beauty/ioctl.c +1 -1
index 52242fa4072b0..e19eb6ea361d7 100644
@@ -21,7 +21,7 @@
 static size_t ioctl__scnprintf_tty_cmd(int nr, int dir, char *bf, size_t size)
 {
 	static const char *ioctl_tty_cmd[] = {
-	"TCGETS", "TCSETS", "TCSETSW", "TCSETSF", "TCGETA", "TCSETA", "TCSETAW",
+	[_IOC_NR(TCGETS)] = "TCGETS", "TCSETS", "TCSETSW", "TCSETSF", "TCGETA", "TCSETA", "TCSETAW",
 	"TCSETAF", "TCSBRK", "TCXONC", "TCFLSH", "TIOCEXCL", "TIOCNXCL", "TIOCSCTTY",
 	"TIOCGPGRP", "TIOCSPGRP", "TIOCOUTQ", "TIOCSTI", "TIOCGWINSZ", "TIOCSWINSZ",
 	"TIOCMGET", "TIOCMBIS", "TIOCMBIC", "TIOCMSET", "TIOCGSOFTCAR", "TIOCSSOFTCAR",
Signature · 1 line
2.20.1
author maintainer
#133 lore raw

PATCH 126/203 media: saa7134: fix terminology around saa7134_i2c_eeprom_md7134_gate()

In reply to Sasha Levin

From: "Maciej S. Szmigiero" <[email protected]>

[ Upstream commit 9d802222a3405599d6e1984d9324cddf592ea1f4 ]

saa7134_i2c_eeprom_md7134_gate() function and the associated comment uses an inverted i2c gate open / closed terminology.
Let's fix this.

---
 drivers/media/pci/saa7134/saa7134-i2c.c | 12 ++++++++----
 1 file changed, 8 insertions(+), 4 deletions(-)
drivers/media/pci/saa7134/saa7134-i2c.c +8 -4
index 493b1858815fb..04e85765373ec 100644
@@ -342,7 +342,11 @@ static const struct i2c_client saa7134_client_template = {
 
 /* ----------------------------------------------------------- */
 
-/* On Medion 7134 reading EEPROM needs DVB-T demod i2c gate open */
+/*
+ * On Medion 7134 reading the SAA7134 chip config EEPROM needs DVB-T
+ * demod i2c gate closed due to an address clash between this EEPROM
+ * and the demod one.
+ */
 static void saa7134_i2c_eeprom_md7134_gate(struct saa7134_dev *dev)
 {
 	u8 subaddr = 0x7, dmdregval;
@@ -359,14 +363,14 @@ static void saa7134_i2c_eeprom_md7134_gate(struct saa7134_dev *dev)
 
 	ret = i2c_transfer(&dev->i2c_adap, i2cgatemsg_r, 2);
 	if ((ret == 2) && (dmdregval & 0x2)) {
-		pr_debug("%s: DVB-T demod i2c gate was left closed\n",
+		pr_debug("%s: DVB-T demod i2c gate was left open\n",
 			 dev->name);
 
 		data[0] = subaddr;
 		data[1] = (dmdregval & ~0x2);
 		if (i2c_transfer(&dev->i2c_adap, i2cgatemsg_w, 1) != 1)
-			pr_err("%s: EEPROM i2c gate open failure\n",
-			  dev->name);
+			pr_err("%s: EEPROM i2c gate close failure\n",
+			       dev->name);
 	}
 }
 
Signature · 1 line
2.20.1
author maintainer
#128 lore raw

PATCH 121/203 PM / devfreq: passive: Use non-devm notifiers

In reply to Sasha Levin

From: Leonard Crestez <[email protected]>

[ Upstream commit 0ef7c7cce43f6ecc2b96d447e69b2900a9655f7c ]

The devfreq passive governor registers and unregisters devfreq transition notifiers on DEVFREQ_GOV_START/GOV_STOP using devm wrappers.

If devfreq itself is registered with devm then a warning is triggered on rmmod from devm_devfreq_unregister_notifier. Call stack looks like this:

	devm_devfreq_unregister_notifier+0x30/0x40
	devfreq_passive_event_handler+0x4c/0x88
	devfreq_remove_device.part.8+0x6c/0x9c
	devm_devfreq_dev_release+0x18/0x20
	release_nodes+0x1b0/0x220
	devres_release_all+0x78/0x84
	device_release_driver_internal+0x100/0x1c0
	driver_detach+0x4c/0x90
	bus_remove_driver+0x7c/0xd0
	driver_unregister+0x2c/0x58
	platform_driver_unregister+0x10/0x18
	imx_devfreq_platdrv_exit+0x14/0xd40 [imx_devfreq]

This happens because devres_release_all will first remove all the nodes into a separate todo list so the nested devres_release from devm_devfreq_unregister_notifier won't find anything.

Fix the warning by calling the non-devm APIS for frequency notification. Using devm wrappers is not actually useful for a governor anyway: it relies on the devfreq core to correctly match the GOV_START/GOV_STOP notifications.

Fixes 996133119f57 ("PM / devfreq: Add new passive governor")
---
 drivers/devfreq/governor_passive.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/devfreq/governor_passive.c +3 -3
index 58308948b8637..da485477065c5 100644
@@ -165,12 +165,12 @@ static int devfreq_passive_event_handler(struct devfreq *devfreq,
 			p_data->this = devfreq;
 
 		nb->notifier_call = devfreq_passive_notifier_call;
-		ret = devm_devfreq_register_notifier(dev, parent, nb,
+		ret = devfreq_register_notifier(parent, nb,
 					DEVFREQ_TRANSITION_NOTIFIER);
 		break;
 	case DEVFREQ_GOV_STOP:
-		devm_devfreq_unregister_notifier(dev, parent, nb,
-					DEVFREQ_TRANSITION_NOTIFIER);
+		WARN_ON(devfreq_unregister_notifier(parent, nb,
+					DEVFREQ_TRANSITION_NOTIFIER));
 		break;
 	default:
 		break;
Signature · 1 line
2.20.1
author maintainer
#125 lore raw

PATCH 118/203 soc: renesas: Enable ARM_ERRATA_754322 for affected Cortex-A9

In reply to Sasha Levin

From: Geert Uytterhoeven <[email protected]>

[ Upstream commit 2eced4607a1e6f51f928ae3e521fe02be5cb7d23 ]

ARM Erratum 754322 affects Cortex-A9 revisions r2p* and r3p*.

Automatically enable support code to mitigate the erratum when compiling a kernel for any of the affected Renesas SoCs:
- RZ/A1: r3p0,
- R-Mobile A1: r2p4,
- R-Car M1A: r2p2-00rel0,
- R-Car H1: r3p0,
- SH-Mobile AG5: r2p2.

EMMA Mobile EV2 (r1p3) and RZ/A2 (r4p1) are not affected.

---
 drivers/soc/renesas/Kconfig | 5 +++++
 1 file changed, 5 insertions(+)
drivers/soc/renesas/Kconfig +5 -0
index 2bbf49e5d4418..9583c542c47f7 100644
@@ -55,6 +55,7 @@ config ARCH_EMEV2
 
 config ARCH_R7S72100
 	bool "RZ/A1H (R7S72100)"
+	select ARM_ERRATA_754322
 	select PM
 	select PM_GENERIC_DOMAINS
 	select RENESAS_OSTM
@@ -78,6 +79,7 @@ config ARCH_R8A73A4
 config ARCH_R8A7740
 	bool "R-Mobile A1 (R8A77400)"
 	select ARCH_RMOBILE
+	select ARM_ERRATA_754322
 	select RENESAS_INTC_IRQPIN
 
 config ARCH_R8A7743
@@ -105,10 +107,12 @@ config ARCH_R8A77470
 config ARCH_R8A7778
 	bool "R-Car M1A (R8A77781)"
 	select ARCH_RCAR_GEN1
+	select ARM_ERRATA_754322
 
 config ARCH_R8A7779
 	bool "R-Car H1 (R8A77790)"
 	select ARCH_RCAR_GEN1
+	select ARM_ERRATA_754322
 	select HAVE_ARM_SCU if SMP
 	select HAVE_ARM_TWD if SMP
 	select SYSC_R8A7779
@@ -152,6 +156,7 @@ config ARCH_R9A06G032
 config ARCH_SH73A0
 	bool "SH-Mobile AG5 (R8A73A00)"
 	select ARCH_RMOBILE
+	select ARM_ERRATA_754322
 	select HAVE_ARM_SCU if SMP
 	select HAVE_ARM_TWD if SMP
 	select RENESAS_INTC_IRQPIN
Signature · 1 line
2.20.1
author maintainer
#122 lore raw

PATCH 115/203 EDAC/amd64: Decode syndrome before translating address

In reply to Sasha Levin

From: Yazen Ghannam <[email protected]>

[ Upstream commit 8a2eaab7daf03b23ac902481218034ae2fae5e16 ]

AMD Family 17h systems currently require address translation in order to report the system address of a DRAM ECC error. This is currently done before decoding the syndrome information. The syndrome information does not depend on the address translation, so the proper EDAC csrow/channel reporting can function without the address. However, the syndrome information will not be decoded if the address translation fails.

Decode the syndrome information before doing the address translation. The syndrome information is architecturally defined in MCA_SYND and can be considered robust. The address translation is system-specific and may fail on newer systems without proper updates to the translation algorithm.

Fixes 713ad54675fd ("EDAC, amd64: Define and register UMC error decode function")
Cc James Morse <[email protected]>
Cc Mauro Carvalho Chehab <[email protected]>
Cc Tony Luck <[email protected]>
---
 drivers/edac/amd64_edac.c | 14 +++++++-------
 1 file changed, 7 insertions(+), 7 deletions(-)
drivers/edac/amd64_edac.c +7 -7
index ffe56a8fe39da..608fdab566b32 100644
@@ -2550,13 +2550,6 @@ static void decode_umc_error(int node_id, struct mce *m)
 
 	err.channel = find_umc_channel(m);
 
-	if (umc_normaddr_to_sysaddr(m->addr, pvt->mc_node_id, err.channel, &sys_addr)) {
-		err.err_code = ERR_NORM_ADDR;
-		goto log_error;
-	}
-
-	error_address_to_page_and_offset(sys_addr, &err);
-
 	if (!(m->status & MCI_STATUS_SYNDV)) {
 		err.err_code = ERR_SYND;
 		goto log_error;
@@ -2573,6 +2566,13 @@ static void decode_umc_error(int node_id, struct mce *m)
 
 	err.csrow = m->synd & 0x7;
 
+	if (umc_normaddr_to_sysaddr(m->addr, pvt->mc_node_id, err.channel, &sys_addr)) {
+		err.err_code = ERR_NORM_ADDR;
+		goto log_error;
+	}
+
+	error_address_to_page_and_offset(sys_addr, &err);
+
 log_error:
 	__log_ecc_error(mci, &err, ecc_type);
 }
Signature · 1 line
2.20.1
author maintainer
#121 lore raw

PATCH 114/203 EDAC/amd64: Recognize DRAM device type ECC capability

In reply to Sasha Levin

From: Yazen Ghannam <[email protected]>

[ Upstream commit f8be8e5680225ac9caf07d4545f8529b7395327f ]

AMD Family 17h systems support x4 and x16 DRAM devices. However, the device type is not checked when setting mci.edac_ctl_cap.

Set the appropriate capability flag based on the device type.

Default to x8 DRAM device when neither the x4 or x16 bits are set.

[ bp: reverse cpk_en check to save an indentation level. ]

Fixes 2d09d8f301f5 ("EDAC, amd64: Determine EDAC MC capabilities on Fam17h")
Cc James Morse <[email protected]>
Cc Mauro Carvalho Chehab <[email protected]>
Cc Tony Luck <[email protected]>
---
 drivers/edac/amd64_edac.c | 14 ++++++++++++--
 1 file changed, 12 insertions(+), 2 deletions(-)
drivers/edac/amd64_edac.c +12 -2
index dd60cf5a3d969..ffe56a8fe39da 100644
@@ -3150,12 +3150,15 @@ static bool ecc_enabled(struct pci_dev *F3, u16 nid)
 static inline void
 f17h_determine_edac_ctl_cap(struct mem_ctl_info *mci, struct amd64_pvt *pvt)
 {
-	u8 i, ecc_en = 1, cpk_en = 1;
+	u8 i, ecc_en = 1, cpk_en = 1, dev_x4 = 1, dev_x16 = 1;
 
 	for_each_umc(i) {
 		if (pvt->umc[i].sdp_ctrl & UMC_SDP_INIT) {
 			ecc_en &= !!(pvt->umc[i].umc_cap_hi & UMC_ECC_ENABLED);
 			cpk_en &= !!(pvt->umc[i].umc_cap_hi & UMC_ECC_CHIPKILL_CAP);
+
+			dev_x4  &= !!(pvt->umc[i].dimm_cfg & BIT(6));
+			dev_x16 &= !!(pvt->umc[i].dimm_cfg & BIT(7));
 		}
 	}
 
@@ -3163,8 +3166,15 @@ f17h_determine_edac_ctl_cap(struct mem_ctl_info *mci, struct amd64_pvt *pvt)
 	if (ecc_en) {
 		mci->edac_ctl_cap |= EDAC_FLAG_SECDED;
 
-		if (cpk_en)
+		if (!cpk_en)
+			return;
+
+		if (dev_x4)
 			mci->edac_ctl_cap |= EDAC_FLAG_S4ECD4ED;
+		else if (dev_x16)
+			mci->edac_ctl_cap |= EDAC_FLAG_S16ECD16ED;
+		else
+			mci->edac_ctl_cap |= EDAC_FLAG_S8ECD8ED;
 	}
 }
 
Signature · 1 line
2.20.1
author maintainer
#126 lore raw

PATCH 119/203 PM / devfreq: Fix kernel oops on governor module load

In reply to Sasha Levin

From: Ezequiel Garcia <[email protected]>

[ Upstream commit 7544fd7f384591038646d3cd9efb311ab4509e24 ]

A bit unexpectedly (but still documented), request_module may return a positive value, in case of a modprobe error. This is currently causing issues in the devfreq framework.

When a request_module exits with a positive value, we currently return that via ERR_PTR. However, because the value is positive, it's not a ERR_VALUE proper, and is therefore treated as a valid struct devfreq_governor pointer, leading to a kernel oops.

Fix this by returning -EINVAL if request_module returns a positive value.

Fixes b53b0128052ff ("PM / devfreq: Fix static checker warning in try_then_request_governor")
---
 drivers/devfreq/devfreq.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/devfreq/devfreq.c +1 -1
index ab22bf8a12d69..a0e19802149fc 100644
@@ -254,7 +254,7 @@ static struct devfreq_governor *try_then_request_governor(const char *name)
 		/* Restore previous state before return */
 		mutex_lock(&devfreq_list_lock);
 		if (err)
-			return ERR_PTR(err);
+			return (err < 0) ? ERR_PTR(err) : ERR_PTR(-EINVAL);
 
 		governor = find_devfreq_governor(name);
 	}
Signature · 1 line
2.20.1
author maintainer
#124 lore raw

PATCH 117/203 soc: renesas: rmobile-sysc: Set GENPD_FLAG_ALWAYS_ON for always-on domain

In reply to Sasha Levin

From: Geert Uytterhoeven <[email protected]>

[ Upstream commit af0bc634728c0bc6a3f66f911f227d5c6396db88 ]

Currently the R-Mobile "always-on" PM Domain is implemented by returning -EBUSY from the generic_pm_domain.power_off() callback, and doing nothing in the generic_pm_domain.power_on() callback. However, this means the PM Domain core code is not aware of the semantics of this special domain, leading to boot warnings like the following on SH/R-Mobile SoCs:

sh_cmt e6130000.timer: PM domain c5 will not be powered off

Fix this by making the always-on nature of the domain explicit instead, by setting the GENPD_FLAG_ALWAYS_ON flag. This removes the need for the domain to provide power control callbacks.

---
 drivers/soc/renesas/rmobile-sysc.c | 31 +++++++++++++++---------------
 1 file changed, 16 insertions(+), 15 deletions(-)
drivers/soc/renesas/rmobile-sysc.c +16 -15
index 421ae1c887d82..54b616ad4a62a 100644
@@ -48,12 +48,8 @@ struct rmobile_pm_domain *to_rmobile_pd(struct generic_pm_domain *d)
 static int rmobile_pd_power_down(struct generic_pm_domain *genpd)
 {
 	struct rmobile_pm_domain *rmobile_pd = to_rmobile_pd(genpd);
-	unsigned int mask;
+	unsigned int mask = BIT(rmobile_pd->bit_shift);
 
-	if (rmobile_pd->bit_shift == ~0)
-		return -EBUSY;
-
-	mask = BIT(rmobile_pd->bit_shift);
 	if (rmobile_pd->suspend) {
 		int ret = rmobile_pd->suspend();
 
@@ -80,14 +76,10 @@ static int rmobile_pd_power_down(struct generic_pm_domain *genpd)
 
 static int __rmobile_pd_power_up(struct rmobile_pm_domain *rmobile_pd)
 {
-	unsigned int mask;
+	unsigned int mask = BIT(rmobile_pd->bit_shift);
 	unsigned int retry_count;
 	int ret = 0;
 
-	if (rmobile_pd->bit_shift == ~0)
-		return 0;
-
-	mask = BIT(rmobile_pd->bit_shift);
 	if (__raw_readl(rmobile_pd->base + PSTR) & mask)
 		return ret;
 
@@ -122,11 +114,15 @@ static void rmobile_init_pm_domain(struct rmobile_pm_domain *rmobile_pd)
 	struct dev_power_governor *gov = rmobile_pd->gov;
 
 	genpd->flags |= GENPD_FLAG_PM_CLK | GENPD_FLAG_ACTIVE_WAKEUP;
-	genpd->power_off		= rmobile_pd_power_down;
-	genpd->power_on			= rmobile_pd_power_up;
-	genpd->attach_dev		= cpg_mstp_attach_dev;
-	genpd->detach_dev		= cpg_mstp_detach_dev;
-	__rmobile_pd_power_up(rmobile_pd);
+	genpd->attach_dev = cpg_mstp_attach_dev;
+	genpd->detach_dev = cpg_mstp_detach_dev;
+
+	if (!(genpd->flags & GENPD_FLAG_ALWAYS_ON)) {
+		genpd->power_off = rmobile_pd_power_down;
+		genpd->power_on = rmobile_pd_power_up;
+		__rmobile_pd_power_up(rmobile_pd);
+	}
+
 	pm_genpd_init(genpd, gov ? : &simple_qos_governor, false);
 }
 
@@ -270,6 +266,11 @@ static void __init rmobile_setup_pm_domain(struct device_node *np,
 		break;
 
 	case PD_NORMAL:
+		if (pd->bit_shift == ~0) {
+			/* Top-level always-on domain */
+			pr_debug("PM domain %s is always-on domain\n", name);
+			pd->genpd.flags |= GENPD_FLAG_ALWAYS_ON;
+		}
 		break;
 	}
 
Signature · 1 line
2.20.1
author maintainer
#123 lore raw

PATCH 116/203 ARM: at91: move platform-specific asm-offset.h to arch/arm/mach-at91

In reply to Sasha Levin

From: Masahiro Yamada <[email protected]>

[ Upstream commit 9fac85a6db8999922f2cd92dfe2e83e063b31a94 ]

<generated/at91_pm_data-offsets.h> is only generated and included by arch/arm/mach-at91/, so it does not need to reside in the globally visible include/generated/.

I renamed it to arch/arm/mach-at91/pm_data-offsets.h since the prefix 'at91_' is just redundant in mach-at91/.

My main motivation of this change is to avoid the race condition for the parallel build (-j) when CONFIG_IKHEADERS is enabled.

When it is enabled, all the headers under include/ are archived into kernel/kheaders_data.tar.xz and exposed in the sysfs.

In the parallel build, we have no idea in which order files are built.

- If at91_pm_data-offsets.h is built before kheaders_data.tar.xz, the header will be included in the archive. Probably nobody will use it, but it is harmless except that it will increase the archive size needlessly.

- If kheaders_data.tar.xz is built before at91_pm_data-offsets.h, the header will not be included in the archive. However, in the next build, the archive will be re-generated to include the newly-found at91_pm_data-offsets.h. This is not nice from the build system point of view.

- If at91_pm_data-offsets.h and kheaders_data.tar.xz are built at the same time, the corrupted header might be included in the archive, which does not look nice either.

This commit fixes the race.

---
 arch/arm/mach-at91/.gitignore   | 1 +
 arch/arm/mach-at91/Makefile     | 5 +++--
 arch/arm/mach-at91/pm_suspend.S | 2 +-
 3 files changed, 5 insertions(+), 3 deletions(-)
 create mode 100644 arch/arm/mach-at91/.gitignore
arch/arm/mach-at91/.gitignore new file +1 -0
new file mode 100644
index 0000000000000..2ecd6f51c8a95
@@ -0,0 +1 @@
+pm_data-offsets.h
arch/arm/mach-at91/Makefile +3 -2
index 31b61f0e1c077..de64301dcff25 100644
@@ -19,9 +19,10 @@ ifeq ($(CONFIG_PM_DEBUG),y)
 CFLAGS_pm.o += -DDEBUG
 endif
 
-include/generated/at91_pm_data-offsets.h: arch/arm/mach-at91/pm_data-offsets.s FORCE
+$(obj)/pm_data-offsets.h: $(obj)/pm_data-offsets.s FORCE
 	$(call filechk,offsets,__PM_DATA_OFFSETS_H__)
 
-arch/arm/mach-at91/pm_suspend.o: include/generated/at91_pm_data-offsets.h
+$(obj)/pm_suspend.o: $(obj)/pm_data-offsets.h
 
 targets += pm_data-offsets.s
+clean-files += pm_data-offsets.h
arch/arm/mach-at91/pm_suspend.S +1 -1
index c751f047b1166..ed57c879d4e17 100644
@@ -10,7 +10,7 @@
 #include <linux/linkage.h>
 #include <linux/clk/at91_pmc.h>
 #include "pm.h"
-#include "generated/at91_pm_data-offsets.h"
+#include "pm_data-offsets.h"
 
 #define	SRAMC_SELF_FRESH_ACTIVE		0x01
 #define	SRAMC_SELF_FRESH_EXIT		0x00
Signature · 1 line
2.20.1
author maintainer
#117 lore raw

PATCH 110/203 media: dvb-core: fix a memory leak bug

In reply to Sasha Levin

From: Wenwen Wang <[email protected]>

[ Upstream commit fcd5ce4b3936242e6679875a4d3c3acfc8743e15 ]

In dvb_create_media_entity(), 'dvbdev->entity' is allocated through kzalloc(). Then, 'dvbdev->pads' is allocated through kcalloc(). However, if kcalloc() fails, the allocated 'dvbdev->entity' is not deallocated, leading to a memory leak bug. To fix this issue, free 'dvbdev->entity' before returning -ENOMEM.

---
 drivers/media/dvb-core/dvbdev.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/media/dvb-core/dvbdev.c +3 -1
index a3393cd4e584f..7557fbf9d3068 100644
@@ -339,8 +339,10 @@ static int dvb_create_media_entity(struct dvb_device *dvbdev,
 	if (npads) {
 		dvbdev->pads = kcalloc(npads, sizeof(*dvbdev->pads),
 				       GFP_KERNEL);
-		if (!dvbdev->pads)
+		if (!dvbdev->pads) {
+			kfree(dvbdev->entity);
 			return -ENOMEM;
+		}
 	}
 
 	switch (type) {
Signature · 1 line
2.20.1
author maintainer
#116 lore raw

PATCH 109/203 posix-cpu-timers: Sanitize bogus WARNONS

In reply to Sasha Levin

From: Thomas Gleixner <[email protected]>

[ Upstream commit 692117c1f7a6770ed41dd8f277cd9fed1dfb16f1 ]

Warning when p == NULL and then proceeding and dereferencing p does not make any sense as the kernel will crash with a NULL pointer dereference right away.

Bailing out when p == NULL and returning an error code does not cure the underlying problem which caused p to be NULL. Though it might allow to do proper debugging.

Same applies to the clock id check in set_process_cpu_timer().

Clean them up and make them return without trying to do further damage.

---
 kernel/time/posix-cpu-timers.c | 20 +++++++++++++-------
 1 file changed, 13 insertions(+), 7 deletions(-)
kernel/time/posix-cpu-timers.c +13 -7
index 0a426f4e31251..5bbad147a90cf 100644
@@ -375,7 +375,8 @@ static int posix_cpu_timer_del(struct k_itimer *timer)
 	struct sighand_struct *sighand;
 	struct task_struct *p = timer->it.cpu.task;
 
-	WARN_ON_ONCE(p == NULL);
+	if (WARN_ON_ONCE(!p))
+		return -EINVAL;
 
 	/*
 	 * Protect against sighand release/switch in exit/exec and process/
@@ -580,7 +581,8 @@ static int posix_cpu_timer_set(struct k_itimer *timer, int timer_flags,
 	u64 old_expires, new_expires, old_incr, val;
 	int ret;
 
-	WARN_ON_ONCE(p == NULL);
+	if (WARN_ON_ONCE(!p))
+		return -EINVAL;
 
 	/*
 	 * Use the to_ktime conversion because that clamps the maximum
@@ -715,10 +717,11 @@ static int posix_cpu_timer_set(struct k_itimer *timer, int timer_flags,
 
 static void posix_cpu_timer_get(struct k_itimer *timer, struct itimerspec64 *itp)
 {
-	u64 now;
 	struct task_struct *p = timer->it.cpu.task;
+	u64 now;
 
-	WARN_ON_ONCE(p == NULL);
+	if (WARN_ON_ONCE(!p))
+		return;
 
 	/*
 	 * Easy part: convert the reload time.
@@ -1000,12 +1003,13 @@ static void check_process_timers(struct task_struct *tsk,
  */
 static void posix_cpu_timer_rearm(struct k_itimer *timer)
 {
+	struct task_struct *p = timer->it.cpu.task;
 	struct sighand_struct *sighand;
 	unsigned long flags;
-	struct task_struct *p = timer->it.cpu.task;
 	u64 now;
 
-	WARN_ON_ONCE(p == NULL);
+	if (WARN_ON_ONCE(!p))
+		return;
 
 	/*
 	 * Fetch the current sample and update the timer's expiry time.
@@ -1202,7 +1206,9 @@ void set_process_cpu_timer(struct task_struct *tsk, unsigned int clock_idx,
 	u64 now;
 	int ret;
 
-	WARN_ON_ONCE(clock_idx == CPUCLOCK_SCHED);
+	if (WARN_ON_ONCE(clock_idx >= CPUCLOCK_SCHED))
+		return;
+
 	ret = cpu_timer_sample_group(clock_idx, tsk, &now);
 
 	if (oldval && ret != -EINVAL) {
Signature · 1 line
2.20.1