usb: Fix Kconfig indentation
Subsystems (4)
PATCH 1/1 usb: Fix Kconfig indentation
Adjust indentation from spaces to tab (+optional two spaces) as in coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by Krzysztof Kozlowski <[email protected]>
--- drivers/usb/dwc3/Kconfig | 4 +- drivers/usb/gadget/legacy/Kconfig | 20 ++++----- drivers/usb/gadget/udc/Kconfig | 2 +- drivers/usb/host/Kconfig | 68 +++++++++++++++--------------- drivers/usb/misc/Kconfig | 8 ++-- drivers/usb/misc/sisusbvga/Kconfig | 2 +- drivers/usb/serial/Kconfig | 44 +++++++++---------- 7 files changed, 74 insertions(+), 74 deletions(-)
drivers/usb/dwc3/Kconfig +2 -2
@@ -103,7 +103,7 @@ config USB_DWC3_MESON_G12A default USB_DWC3 select USB_ROLE_SWITCH help - Support USB2/3 functionality in Amlogic G12A platforms. + Support USB2/3 functionality in Amlogic G12A platforms. Say 'Y' or 'M' if you have one such device. config USB_DWC3_OF_SIMPLE
@@ -111,7 +111,7 @@ config USB_DWC3_OF_SIMPLE depends on OF && COMMON_CLK default USB_DWC3 help - Support USB2/3 functionality in simple SoC integrations. + Support USB2/3 functionality in simple SoC integrations. Currently supports Xilinx and Qualcomm DWC USB3 IP. Say 'Y' or 'M' if you have one such device.
drivers/usb/gadget/legacy/Kconfig +10 -10
@@ -154,16 +154,16 @@ config USB_ETH_EEM select USB_LIBCOMPOSITE select USB_F_EEM help - CDC EEM is a newer USB standard that is somewhat simpler than CDC ECM - and therefore can be supported by more hardware. Technically ECM and - EEM are designed for different applications. The ECM model extends - the network interface to the target (e.g. a USB cable modem), and the - EEM model is for mobile devices to communicate with hosts using - ethernet over USB. For Linux gadgets, however, the interface with - the host is the same (a usbX device), so the differences are minimal. - - If you say "y" here, the Ethernet gadget driver will use the EEM - protocol rather than ECM. If unsure, say "n". + CDC EEM is a newer USB standard that is somewhat simpler than CDC ECM + and therefore can be supported by more hardware. Technically ECM and + EEM are designed for different applications. The ECM model extends + the network interface to the target (e.g. a USB cable modem), and the + EEM model is for mobile devices to communicate with hosts using + ethernet over USB. For Linux gadgets, however, the interface with + the host is the same (a usbX device), so the differences are minimal. + + If you say "y" here, the Ethernet gadget driver will use the EEM + protocol rather than ECM. If unsure, say "n". config USB_G_NCM tristate "Network Control Model (NCM) support"
drivers/usb/gadget/udc/Kconfig +1 -1
@@ -123,7 +123,7 @@ config USB_GR_UDC tristate "Aeroflex Gaisler GRUSBDC USB Peripheral Controller Driver" depends on HAS_DMA help - Select this to support Aeroflex Gaisler GRUSBDC cores from the GRLIB + Select this to support Aeroflex Gaisler GRUSBDC cores from the GRLIB VHDL IP core library. config USB_OMAP
drivers/usb/host/Kconfig +34 -34
117 lines not on this page · raw message
drivers/usb/misc/Kconfig +4 -4
@@ -191,8 +191,8 @@ config USB_TEST including sample test device firmware and "how to use it". config USB_EHSET_TEST_FIXTURE - tristate "USB EHSET Test Fixture driver" - help + tristate "USB EHSET Test Fixture driver" + help Say Y here if you want to support the special test fixture device used for the USB-IF Embedded Host High-Speed Electrical Test procedure.
@@ -247,13 +247,13 @@ config USB_HSIC_USB3503 depends on I2C select REGMAP_I2C help - This option enables support for SMSC USB3503 HSIC to USB 2.0 Driver. + This option enables support for SMSC USB3503 HSIC to USB 2.0 Driver. config USB_HSIC_USB4604 tristate "USB4604 HSIC to USB20 Driver" depends on I2C help - This option enables support for SMSC USB4604 HSIC to USB 2.0 Driver. + This option enables support for SMSC USB4604 HSIC to USB 2.0 Driver. config USB_LINK_LAYER_TEST tristate "USB Link Layer Test driver"
drivers/usb/misc/sisusbvga/Kconfig +1 -1
@@ -4,7 +4,7 @@ config USB_SISUSBVGA tristate "USB 2.0 SVGA dongle support (Net2280/SiS315)" depends on (USB_MUSB_HDRC || USB_EHCI_HCD) select FONT_SUPPORT if USB_SISUSBVGA_CON - ---help--- + ---help--- Say Y here if you intend to attach a USB2VGA dongle based on a Net2280 and a SiS315 chip.
drivers/usb/serial/Kconfig +22 -22
66 lines not on this page · raw message
Signature · 1 line
2.17.1
Quoted 5 lines · Krzysztof Kozlowski
Adjust indentation from spaces to tab (+optional two spaces) as in coding style with command like:
$ sed -e 's/^ /\t/' -i */KconfigSigned-off-by Krzysztof Kozlowski <[email protected]>
Quoted 9 lines
--- drivers/usb/dwc3/Kconfig | 4 +- drivers/usb/gadget/legacy/Kconfig | 20 ++++----- drivers/usb/gadget/udc/Kconfig | 2 +- drivers/usb/host/Kconfig | 68 +++++++++++++++--------------- drivers/usb/misc/Kconfig | 8 ++-- drivers/usb/misc/sisusbvga/Kconfig | 2 +- drivers/usb/serial/Kconfig | 44 +++++++++---------- 7 files changed, 74 insertions(+), 74 deletions(-)
Acked-by Johan Hovold <[email protected]>