Skip to contentSkip to conversation

iio: pressure: bmp280: use devm action and remove labels from probe

PATCH In review Bartosz Golaszewski 2 participants 6 messages Oct 7, 2019 – Nov 2, 2019 IIO

lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 iio: pressure: bmp280: use devm action and remove labels from probe

From: Bartosz Golaszewski <[email protected]>

We can drop some duplicate code if we use devm_action for disabling regulators and pm and the managed variant of iio_device_register().

This allows us to completely remove all remove() callbacks from both i2c and spi code.

---
v1 -> v2:
- squash the patches using devm_iio_device_register() and devm_action to keep the changes bisectable

 drivers/iio/pressure/bmp280-core.c | 62 +++++++++++++++---------------
 drivers/iio/pressure/bmp280-i2c.c  |  6 ---
 drivers/iio/pressure/bmp280-spi.c  |  6 ---
 drivers/iio/pressure/bmp280.h      |  1 -
 4 files changed, 30 insertions(+), 45 deletions(-)
drivers/iio/pressure/bmp280-core.c +30 -32
index c2988dbdb1a7..79254dd26dfd 100644
@@ -984,6 +984,22 @@ static int bmp085_fetch_eoc_irq(struct device *dev,
 	return 0;
 }
 
+static void bmp280_pm_disable(void *data)
+{
+	struct device *dev = data;
+
+	pm_runtime_get_sync(dev);
+	pm_runtime_put_noidle(dev);
+	pm_runtime_disable(dev);
+}
+
+static void bmp280_regulators_disable(void *data)
+{
+	struct regulator_bulk_data *supplies = data;
+
+	regulator_bulk_disable(BMP280_NUM_SUPPLIES, supplies);
+}
+
 int bmp280_common_probe(struct device *dev,
 			struct regmap *regmap,
 			unsigned int chip,
@@ -1055,6 +1071,11 @@ int bmp280_common_probe(struct device *dev,
 		return ret;
 	}
 
+	ret = devm_add_action_or_reset(dev, bmp280_regulators_disable,
+				       data->supplies);
+	if (ret)
+		return ret;
+
 	/* Wait to make sure we started up properly */
 	usleep_range(data->start_up_time, data->start_up_time + 100);
 
@@ -1069,17 +1090,16 @@ int bmp280_common_probe(struct device *dev,
 	data->regmap = regmap;
 	ret = regmap_read(regmap, BMP280_REG_ID, &chip_id);
 	if (ret < 0)
-		goto out_disable_regulators;
+		return ret;
 	if (chip_id != chip) {
 		dev_err(dev, "bad chip id: expected %x got %x\n",
 			chip, chip_id);
-		ret = -EINVAL;
-		goto out_disable_regulators;
+		return -EINVAL;
 	}
 
 	ret = data->chip_info->chip_config(data);
 	if (ret < 0)
-		goto out_disable_regulators;
+		return ret;
 
 	dev_set_drvdata(dev, indio_dev);
 
@@ -1093,14 +1113,14 @@ int bmp280_common_probe(struct device *dev,
 		if (ret < 0) {
 			dev_err(data->dev,
 				"failed to read calibration coefficients\n");
-			goto out_disable_regulators;
+			return ret;
 		}
 	} else if (chip_id == BMP280_CHIP_ID || chip_id == BME280_CHIP_ID) {
 		ret = bmp280_read_calib(data, &data->calib.bmp280, chip_id);
 		if (ret < 0) {
 			dev_err(data->dev,
 				"failed to read calibration coefficients\n");
-			goto out_disable_regulators;
+			return ret;
 		}
 	}
 
@@ -1112,7 +1132,7 @@ int bmp280_common_probe(struct device *dev,
 	if (irq > 0 || (chip_id  == BMP180_CHIP_ID)) {
 		ret = bmp085_fetch_eoc_irq(dev, name, irq, data);
 		if (ret)
-			goto out_disable_regulators;
+			return ret;
 	}
 
 	/* Enable runtime PM */
@@ -1127,36 +1147,14 @@ int bmp280_common_probe(struct device *dev,
 	pm_runtime_use_autosuspend(dev);
 	pm_runtime_put(dev);
 
-	ret = iio_device_register(indio_dev);
+	ret = devm_add_action_or_reset(dev, bmp280_pm_disable, dev);
 	if (ret)
-		goto out_runtime_pm_disable;
-
-	return 0;
+		return ret;
 
-out_runtime_pm_disable:
-	pm_runtime_get_sync(data->dev);
-	pm_runtime_put_noidle(data->dev);
-	pm_runtime_disable(data->dev);
-out_disable_regulators:
-	regulator_bulk_disable(BMP280_NUM_SUPPLIES, data->supplies);
-	return ret;
+	return devm_iio_device_register(dev, indio_dev);
 }
 EXPORT_SYMBOL(bmp280_common_probe);
 
-int bmp280_common_remove(struct device *dev)
-{
-	struct iio_dev *indio_dev = dev_get_drvdata(dev);
-	struct bmp280_data *data = iio_priv(indio_dev);
-
-	iio_device_unregister(indio_dev);
-	pm_runtime_get_sync(data->dev);
-	pm_runtime_put_noidle(data->dev);
-	pm_runtime_disable(data->dev);
-	regulator_bulk_disable(BMP280_NUM_SUPPLIES, data->supplies);
-	return 0;
-}
-EXPORT_SYMBOL(bmp280_common_remove);
-
 #ifdef CONFIG_PM
 static int bmp280_runtime_suspend(struct device *dev)
 {
drivers/iio/pressure/bmp280-i2c.c +0 -6
index acd9a3784fb4..3109c8e2cc11 100644
@@ -38,11 +38,6 @@ static int bmp280_i2c_probe(struct i2c_client *client,
 				   client->irq);
 }
 
-static int bmp280_i2c_remove(struct i2c_client *client)
-{
-	return bmp280_common_remove(&client->dev);
-}
-
 static const struct acpi_device_id bmp280_acpi_i2c_match[] = {
 	{"BMP0280", BMP280_CHIP_ID },
 	{"BMP0180", BMP180_CHIP_ID },
@@ -82,7 +77,6 @@ static struct i2c_driver bmp280_i2c_driver = {
 		.pm = &bmp280_dev_pm_ops,
 	},
 	.probe		= bmp280_i2c_probe,
-	.remove		= bmp280_i2c_remove,
 	.id_table	= bmp280_i2c_id,
 };
 module_i2c_driver(bmp280_i2c_driver);
drivers/iio/pressure/bmp280-spi.c +0 -6
index 9d57b7a3b134..625b86878ad8 100644
@@ -86,11 +86,6 @@ static int bmp280_spi_probe(struct spi_device *spi)
 				   spi->irq);
 }
 
-static int bmp280_spi_remove(struct spi_device *spi)
-{
-	return bmp280_common_remove(&spi->dev);
-}
-
 static const struct of_device_id bmp280_of_spi_match[] = {
 	{ .compatible = "bosch,bmp085", },
 	{ .compatible = "bosch,bmp180", },
@@ -118,7 +113,6 @@ static struct spi_driver bmp280_spi_driver = {
 	},
 	.id_table = bmp280_spi_id,
 	.probe = bmp280_spi_probe,
-	.remove = bmp280_spi_remove,
 };
 module_spi_driver(bmp280_spi_driver);
 
drivers/iio/pressure/bmp280.h +0 -1
index eda50ef65706..57ba0e85db91 100644
@@ -112,7 +112,6 @@ int bmp280_common_probe(struct device *dev,
 			unsigned int chip,
 			const char *name,
 			int irq);
-int bmp280_common_remove(struct device *dev);
 
 /* PM ops */
 extern const struct dev_pm_ops bmp280_dev_pm_ops;
Signature · 1 line
2.23.0
maintainer
#1 lore raw
Quoted 9 lines · On Mon, 7 Oct 2019 04:41:31 +0200 Bartosz Golaszewski <[email protected]> wrote:

From: Bartosz Golaszewski <[email protected]>

We can drop some duplicate code if we use devm_action for disabling regulators and pm and the managed variant of iio_device_register().

This allows us to completely remove all remove() callbacks from both i2c and spi code.

This is on top of the bulk regulator patch which is awaiting precusors getting to my upstream. I'll hold this one as well on that.

If it looks like I've forgotten it then give me a poke.

Thanks,

Jonathan

Quoted 197 lines

---
v1 -> v2:
- squash the patches using devm_iio_device_register() and devm_action to keep the changes bisectable

 drivers/iio/pressure/bmp280-core.c | 62 +++++++++++++++---------------
 drivers/iio/pressure/bmp280-i2c.c  |  6 ---
 drivers/iio/pressure/bmp280-spi.c  |  6 ---
 drivers/iio/pressure/bmp280.h      |  1 -
 4 files changed, 30 insertions(+), 45 deletions(-)
drivers/iio/pressure/bmp280-core.c +30 -32
index c2988dbdb1a7..79254dd26dfd 100644
@@ -984,6 +984,22 @@ static int bmp085_fetch_eoc_irq(struct device *dev,
 	return 0;
 }
 
+static void bmp280_pm_disable(void *data)
+{
+	struct device *dev = data;
+
+	pm_runtime_get_sync(dev);
+	pm_runtime_put_noidle(dev);
+	pm_runtime_disable(dev);
+}
+
+static void bmp280_regulators_disable(void *data)
+{
+	struct regulator_bulk_data *supplies = data;
+
+	regulator_bulk_disable(BMP280_NUM_SUPPLIES, supplies);
+}
+
 int bmp280_common_probe(struct device *dev,
 			struct regmap *regmap,
 			unsigned int chip,
@@ -1055,6 +1071,11 @@ int bmp280_common_probe(struct device *dev,
 		return ret;
 	}
 
+	ret = devm_add_action_or_reset(dev, bmp280_regulators_disable,
+				       data->supplies);
+	if (ret)
+		return ret;
+
 	/* Wait to make sure we started up properly */
 	usleep_range(data->start_up_time, data->start_up_time + 100);
 
@@ -1069,17 +1090,16 @@ int bmp280_common_probe(struct device *dev,
 	data->regmap = regmap;
 	ret = regmap_read(regmap, BMP280_REG_ID, &chip_id);
 	if (ret < 0)
-		goto out_disable_regulators;
+		return ret;
 	if (chip_id != chip) {
 		dev_err(dev, "bad chip id: expected %x got %x\n",
 			chip, chip_id);
-		ret = -EINVAL;
-		goto out_disable_regulators;
+		return -EINVAL;
 	}
 
 	ret = data->chip_info->chip_config(data);
 	if (ret < 0)
-		goto out_disable_regulators;
+		return ret;
 
 	dev_set_drvdata(dev, indio_dev);
 
@@ -1093,14 +1113,14 @@ int bmp280_common_probe(struct device *dev,
 		if (ret < 0) {
 			dev_err(data->dev,
 				"failed to read calibration coefficients\n");
-			goto out_disable_regulators;
+			return ret;
 		}
 	} else if (chip_id == BMP280_CHIP_ID || chip_id == BME280_CHIP_ID) {
 		ret = bmp280_read_calib(data, &data->calib.bmp280, chip_id);
 		if (ret < 0) {
 			dev_err(data->dev,
 				"failed to read calibration coefficients\n");
-			goto out_disable_regulators;
+			return ret;
 		}
 	}
 
@@ -1112,7 +1132,7 @@ int bmp280_common_probe(struct device *dev,
 	if (irq > 0 || (chip_id  == BMP180_CHIP_ID)) {
 		ret = bmp085_fetch_eoc_irq(dev, name, irq, data);
 		if (ret)
-			goto out_disable_regulators;
+			return ret;
 	}
 
 	/* Enable runtime PM */
@@ -1127,36 +1147,14 @@ int bmp280_common_probe(struct device *dev,
 	pm_runtime_use_autosuspend(dev);
 	pm_runtime_put(dev);
 
-	ret = iio_device_register(indio_dev);
+	ret = devm_add_action_or_reset(dev, bmp280_pm_disable, dev);
 	if (ret)
-		goto out_runtime_pm_disable;
-
-	return 0;
+		return ret;
 
-out_runtime_pm_disable:
-	pm_runtime_get_sync(data->dev);
-	pm_runtime_put_noidle(data->dev);
-	pm_runtime_disable(data->dev);
-out_disable_regulators:
-	regulator_bulk_disable(BMP280_NUM_SUPPLIES, data->supplies);
-	return ret;
+	return devm_iio_device_register(dev, indio_dev);
 }
 EXPORT_SYMBOL(bmp280_common_probe);
 
-int bmp280_common_remove(struct device *dev)
-{
-	struct iio_dev *indio_dev = dev_get_drvdata(dev);
-	struct bmp280_data *data = iio_priv(indio_dev);
-
-	iio_device_unregister(indio_dev);
-	pm_runtime_get_sync(data->dev);
-	pm_runtime_put_noidle(data->dev);
-	pm_runtime_disable(data->dev);
-	regulator_bulk_disable(BMP280_NUM_SUPPLIES, data->supplies);
-	return 0;
-}
-EXPORT_SYMBOL(bmp280_common_remove);
-
 #ifdef CONFIG_PM
 static int bmp280_runtime_suspend(struct device *dev)
 {
drivers/iio/pressure/bmp280-i2c.c +0 -6
index acd9a3784fb4..3109c8e2cc11 100644
@@ -38,11 +38,6 @@ static int bmp280_i2c_probe(struct i2c_client *client,
 				   client->irq);
 }
 
-static int bmp280_i2c_remove(struct i2c_client *client)
-{
-	return bmp280_common_remove(&client->dev);
-}
-
 static const struct acpi_device_id bmp280_acpi_i2c_match[] = {
 	{"BMP0280", BMP280_CHIP_ID },
 	{"BMP0180", BMP180_CHIP_ID },
@@ -82,7 +77,6 @@ static struct i2c_driver bmp280_i2c_driver = {
 		.pm = &bmp280_dev_pm_ops,
 	},
 	.probe		= bmp280_i2c_probe,
-	.remove		= bmp280_i2c_remove,
 	.id_table	= bmp280_i2c_id,
 };
 module_i2c_driver(bmp280_i2c_driver);
drivers/iio/pressure/bmp280-spi.c +0 -6
index 9d57b7a3b134..625b86878ad8 100644
@@ -86,11 +86,6 @@ static int bmp280_spi_probe(struct spi_device *spi)
 				   spi->irq);
 }
 
-static int bmp280_spi_remove(struct spi_device *spi)
-{
-	return bmp280_common_remove(&spi->dev);
-}
-
 static const struct of_device_id bmp280_of_spi_match[] = {
 	{ .compatible = "bosch,bmp085", },
 	{ .compatible = "bosch,bmp180", },
@@ -118,7 +113,6 @@ static struct spi_driver bmp280_spi_driver = {
 	},
 	.id_table = bmp280_spi_id,
 	.probe = bmp280_spi_probe,
-	.remove = bmp280_spi_remove,
 };
 module_spi_driver(bmp280_spi_driver);
 
drivers/iio/pressure/bmp280.h +0 -1
index eda50ef65706..57ba0e85db91 100644
@@ -112,7 +112,6 @@ int bmp280_common_probe(struct device *dev,
 			unsigned int chip,
 			const char *name,
 			int irq);
-int bmp280_common_remove(struct device *dev);
 
 /* PM ops */
 extern const struct dev_pm_ops bmp280_dev_pm_ops;
#2 lore raw

sob., 12 paź 2019 o 15:37 Jonathan Cameron <[email protected]> napisał(a):

Quoted 9 lines
Quoted 5 lines · On Mon, 7 Oct 2019 04:41:31 +0200 Bartosz Golaszewski <[email protected]> wrote:

From: Bartosz Golaszewski <[email protected]>

We can drop some duplicate code if we use devm_action for disabling regulators and pm and the managed variant of iio_device_register().

Quoted 9 lines
Quoted 4 lines

This allows us to completely remove all remove() callbacks from both i2c and spi code.

This is on top of the bulk regulator patch which is awaiting precusors getting to my upstream. I'll hold this one as well on that.

If it looks like I've forgotten it then give me a poke.

Hi Jonathan,

gentle poke after v5.4-rc4. Only one of the three patches is in next so far, the one using bulk regulators is missing too besides this one.

Best regards,
Bartosz Golaszewski

Quoted 202 lines

Thanks,

Jonathan

Quoted 197 lines

---
v1 -> v2:
- squash the patches using devm_iio_device_register() and devm_action to keep the changes bisectable

 drivers/iio/pressure/bmp280-core.c | 62 +++++++++++++++---------------
 drivers/iio/pressure/bmp280-i2c.c  |  6 ---
 drivers/iio/pressure/bmp280-spi.c  |  6 ---
 drivers/iio/pressure/bmp280.h      |  1 -
 4 files changed, 30 insertions(+), 45 deletions(-)
drivers/iio/pressure/bmp280-core.c +30 -32
index c2988dbdb1a7..79254dd26dfd 100644
@@ -984,6 +984,22 @@ static int bmp085_fetch_eoc_irq(struct device *dev,
      return 0;
 }
 
+static void bmp280_pm_disable(void *data)
+{
+     struct device *dev = data;
+
+     pm_runtime_get_sync(dev);
+     pm_runtime_put_noidle(dev);
+     pm_runtime_disable(dev);
+}
+
+static void bmp280_regulators_disable(void *data)
+{
+     struct regulator_bulk_data *supplies = data;
+
+     regulator_bulk_disable(BMP280_NUM_SUPPLIES, supplies);
+}
+
 int bmp280_common_probe(struct device *dev,
                      struct regmap *regmap,
                      unsigned int chip,
@@ -1055,6 +1071,11 @@ int bmp280_common_probe(struct device *dev,
              return ret;
      }
 
+     ret = devm_add_action_or_reset(dev, bmp280_regulators_disable,
+                                    data->supplies);
+     if (ret)
+             return ret;
+
      /* Wait to make sure we started up properly */
      usleep_range(data->start_up_time, data->start_up_time + 100);
 
@@ -1069,17 +1090,16 @@ int bmp280_common_probe(struct device *dev,
      data->regmap = regmap;
      ret = regmap_read(regmap, BMP280_REG_ID, &chip_id);
      if (ret < 0)
-             goto out_disable_regulators;
+             return ret;
      if (chip_id != chip) {
              dev_err(dev, "bad chip id: expected %x got %x\n",
                      chip, chip_id);
-             ret = -EINVAL;
-             goto out_disable_regulators;
+             return -EINVAL;
      }
 
      ret = data->chip_info->chip_config(data);
      if (ret < 0)
-             goto out_disable_regulators;
+             return ret;
 
      dev_set_drvdata(dev, indio_dev);
 
@@ -1093,14 +1113,14 @@ int bmp280_common_probe(struct device *dev,
              if (ret < 0) {
                      dev_err(data->dev,
                              "failed to read calibration coefficients\n");
-                     goto out_disable_regulators;
+                     return ret;
              }
      } else if (chip_id == BMP280_CHIP_ID || chip_id == BME280_CHIP_ID) {
              ret = bmp280_read_calib(data, &data->calib.bmp280, chip_id);
              if (ret < 0) {
                      dev_err(data->dev,
                              "failed to read calibration coefficients\n");
-                     goto out_disable_regulators;
+                     return ret;
              }
      }
 
@@ -1112,7 +1132,7 @@ int bmp280_common_probe(struct device *dev,
      if (irq > 0 || (chip_id  == BMP180_CHIP_ID)) {
              ret = bmp085_fetch_eoc_irq(dev, name, irq, data);
              if (ret)
-                     goto out_disable_regulators;
+                     return ret;
      }
 
      /* Enable runtime PM */
@@ -1127,36 +1147,14 @@ int bmp280_common_probe(struct device *dev,
      pm_runtime_use_autosuspend(dev);
      pm_runtime_put(dev);
 
-     ret = iio_device_register(indio_dev);
+     ret = devm_add_action_or_reset(dev, bmp280_pm_disable, dev);
      if (ret)
-             goto out_runtime_pm_disable;
-
-     return 0;
+             return ret;
 
-out_runtime_pm_disable:
-     pm_runtime_get_sync(data->dev);
-     pm_runtime_put_noidle(data->dev);
-     pm_runtime_disable(data->dev);
-out_disable_regulators:
-     regulator_bulk_disable(BMP280_NUM_SUPPLIES, data->supplies);
-     return ret;
+     return devm_iio_device_register(dev, indio_dev);
 }
 EXPORT_SYMBOL(bmp280_common_probe);
 
-int bmp280_common_remove(struct device *dev)
-{
-     struct iio_dev *indio_dev = dev_get_drvdata(dev);
-     struct bmp280_data *data = iio_priv(indio_dev);
-
-     iio_device_unregister(indio_dev);
-     pm_runtime_get_sync(data->dev);
-     pm_runtime_put_noidle(data->dev);
-     pm_runtime_disable(data->dev);
-     regulator_bulk_disable(BMP280_NUM_SUPPLIES, data->supplies);
-     return 0;
-}
-EXPORT_SYMBOL(bmp280_common_remove);
-
 #ifdef CONFIG_PM
 static int bmp280_runtime_suspend(struct device *dev)
 {
drivers/iio/pressure/bmp280-i2c.c +0 -6
index acd9a3784fb4..3109c8e2cc11 100644
@@ -38,11 +38,6 @@ static int bmp280_i2c_probe(struct i2c_client *client,
                                 client->irq);
 }
 
-static int bmp280_i2c_remove(struct i2c_client *client)
-{
-     return bmp280_common_remove(&client->dev);
-}
-
 static const struct acpi_device_id bmp280_acpi_i2c_match[] = {
      {"BMP0280", BMP280_CHIP_ID },
      {"BMP0180", BMP180_CHIP_ID },
@@ -82,7 +77,6 @@ static struct i2c_driver bmp280_i2c_driver = {
              .pm = &bmp280_dev_pm_ops,
      },
      .probe          = bmp280_i2c_probe,
-     .remove         = bmp280_i2c_remove,
      .id_table       = bmp280_i2c_id,
 };
 module_i2c_driver(bmp280_i2c_driver);
drivers/iio/pressure/bmp280-spi.c +0 -6
index 9d57b7a3b134..625b86878ad8 100644
@@ -86,11 +86,6 @@ static int bmp280_spi_probe(struct spi_device *spi)
                                 spi->irq);
 }
 
-static int bmp280_spi_remove(struct spi_device *spi)
-{
-     return bmp280_common_remove(&spi->dev);
-}
-
 static const struct of_device_id bmp280_of_spi_match[] = {
      { .compatible = "bosch,bmp085", },
      { .compatible = "bosch,bmp180", },
@@ -118,7 +113,6 @@ static struct spi_driver bmp280_spi_driver = {
      },
      .id_table = bmp280_spi_id,
      .probe = bmp280_spi_probe,
-     .remove = bmp280_spi_remove,
 };
 module_spi_driver(bmp280_spi_driver);
 
drivers/iio/pressure/bmp280.h +0 -1
index eda50ef65706..57ba0e85db91 100644
@@ -112,7 +112,6 @@ int bmp280_common_probe(struct device *dev,
                      unsigned int chip,
                      const char *name,
                      int irq);
-int bmp280_common_remove(struct device *dev);
 
 /* PM ops */
 extern const struct dev_pm_ops bmp280_dev_pm_ops;
maintainer
#3 lore raw
Quoted 17 lines · On Mon, 21 Oct 2019 14:47:18 +0200 Bartosz Golaszewski <[email protected]> wrote:

sob., 12 paź 2019 o 15:37 Jonathan Cameron <[email protected]> napisał(a):

Quoted 16 lines
Quoted 9 lines · On Mon, 7 Oct 2019 04:41:31 +0200 Bartosz Golaszewski <[email protected]> wrote:

From: Bartosz Golaszewski <[email protected]>

We can drop some duplicate code if we use devm_action for disabling regulators and pm and the managed variant of iio_device_register().

This allows us to completely remove all remove() callbacks from both i2c and spi code.

This is on top of the bulk regulator patch which is awaiting precusors getting to my upstream. I'll hold this one as well on that.

Quoted 7 lines
Quoted 2 lines

If it looks like I've forgotten it then give me a poke.

Hi Jonathan,

gentle poke after v5.4-rc4. Only one of the three patches is in next so far, the one using bulk regulators is missing too besides this one.

Thanks for the reminder.

Applied to the togreg branch of iio.git and pushed out as testing for the autobuilders to play with it.

Thanks,

Jonathan

Quoted 206 lines

Best regards,
Bartosz Golaszewski

Quoted 202 lines

Thanks,

Jonathan

Quoted 197 lines

---
v1 -> v2:
- squash the patches using devm_iio_device_register() and devm_action to keep the changes bisectable

 drivers/iio/pressure/bmp280-core.c | 62 +++++++++++++++---------------
 drivers/iio/pressure/bmp280-i2c.c  |  6 ---
 drivers/iio/pressure/bmp280-spi.c  |  6 ---
 drivers/iio/pressure/bmp280.h      |  1 -
 4 files changed, 30 insertions(+), 45 deletions(-)
drivers/iio/pressure/bmp280-core.c +30 -32
index c2988dbdb1a7..79254dd26dfd 100644
@@ -984,6 +984,22 @@ static int bmp085_fetch_eoc_irq(struct device *dev,
      return 0;
 }
 
+static void bmp280_pm_disable(void *data)
+{
+     struct device *dev = data;
+
+     pm_runtime_get_sync(dev);
+     pm_runtime_put_noidle(dev);
+     pm_runtime_disable(dev);
+}
+
+static void bmp280_regulators_disable(void *data)
+{
+     struct regulator_bulk_data *supplies = data;
+
+     regulator_bulk_disable(BMP280_NUM_SUPPLIES, supplies);
+}
+
 int bmp280_common_probe(struct device *dev,
                      struct regmap *regmap,
                      unsigned int chip,
@@ -1055,6 +1071,11 @@ int bmp280_common_probe(struct device *dev,
              return ret;
      }
 
+     ret = devm_add_action_or_reset(dev, bmp280_regulators_disable,
+                                    data->supplies);
+     if (ret)
+             return ret;
+
      /* Wait to make sure we started up properly */
      usleep_range(data->start_up_time, data->start_up_time + 100);
 
@@ -1069,17 +1090,16 @@ int bmp280_common_probe(struct device *dev,
      data->regmap = regmap;
      ret = regmap_read(regmap, BMP280_REG_ID, &chip_id);
      if (ret < 0)
-             goto out_disable_regulators;
+             return ret;
      if (chip_id != chip) {
              dev_err(dev, "bad chip id: expected %x got %x\n",
                      chip, chip_id);
-             ret = -EINVAL;
-             goto out_disable_regulators;
+             return -EINVAL;
      }
 
      ret = data->chip_info->chip_config(data);
      if (ret < 0)
-             goto out_disable_regulators;
+             return ret;
 
      dev_set_drvdata(dev, indio_dev);
 
@@ -1093,14 +1113,14 @@ int bmp280_common_probe(struct device *dev,
              if (ret < 0) {
                      dev_err(data->dev,
                              "failed to read calibration coefficients\n");
-                     goto out_disable_regulators;
+                     return ret;
              }
      } else if (chip_id == BMP280_CHIP_ID || chip_id == BME280_CHIP_ID) {
              ret = bmp280_read_calib(data, &data->calib.bmp280, chip_id);
              if (ret < 0) {
                      dev_err(data->dev,
                              "failed to read calibration coefficients\n");
-                     goto out_disable_regulators;
+                     return ret;
              }
      }
 
@@ -1112,7 +1132,7 @@ int bmp280_common_probe(struct device *dev,
      if (irq > 0 || (chip_id  == BMP180_CHIP_ID)) {
              ret = bmp085_fetch_eoc_irq(dev, name, irq, data);
              if (ret)
-                     goto out_disable_regulators;
+                     return ret;
      }
 
      /* Enable runtime PM */
@@ -1127,36 +1147,14 @@ int bmp280_common_probe(struct device *dev,
      pm_runtime_use_autosuspend(dev);
      pm_runtime_put(dev);
 
-     ret = iio_device_register(indio_dev);
+     ret = devm_add_action_or_reset(dev, bmp280_pm_disable, dev);
      if (ret)
-             goto out_runtime_pm_disable;
-
-     return 0;
+             return ret;
 
-out_runtime_pm_disable:
-     pm_runtime_get_sync(data->dev);
-     pm_runtime_put_noidle(data->dev);
-     pm_runtime_disable(data->dev);
-out_disable_regulators:
-     regulator_bulk_disable(BMP280_NUM_SUPPLIES, data->supplies);
-     return ret;
+     return devm_iio_device_register(dev, indio_dev);
 }
 EXPORT_SYMBOL(bmp280_common_probe);
 
-int bmp280_common_remove(struct device *dev)
-{
-     struct iio_dev *indio_dev = dev_get_drvdata(dev);
-     struct bmp280_data *data = iio_priv(indio_dev);
-
-     iio_device_unregister(indio_dev);
-     pm_runtime_get_sync(data->dev);
-     pm_runtime_put_noidle(data->dev);
-     pm_runtime_disable(data->dev);
-     regulator_bulk_disable(BMP280_NUM_SUPPLIES, data->supplies);
-     return 0;
-}
-EXPORT_SYMBOL(bmp280_common_remove);
-
 #ifdef CONFIG_PM
 static int bmp280_runtime_suspend(struct device *dev)
 {
drivers/iio/pressure/bmp280-i2c.c +0 -6
index acd9a3784fb4..3109c8e2cc11 100644
@@ -38,11 +38,6 @@ static int bmp280_i2c_probe(struct i2c_client *client,
                                 client->irq);
 }
 
-static int bmp280_i2c_remove(struct i2c_client *client)
-{
-     return bmp280_common_remove(&client->dev);
-}
-
 static const struct acpi_device_id bmp280_acpi_i2c_match[] = {
      {"BMP0280", BMP280_CHIP_ID },
      {"BMP0180", BMP180_CHIP_ID },
@@ -82,7 +77,6 @@ static struct i2c_driver bmp280_i2c_driver = {
              .pm = &bmp280_dev_pm_ops,
      },
      .probe          = bmp280_i2c_probe,
-     .remove         = bmp280_i2c_remove,
      .id_table       = bmp280_i2c_id,
 };
 module_i2c_driver(bmp280_i2c_driver);
drivers/iio/pressure/bmp280-spi.c +0 -6
index 9d57b7a3b134..625b86878ad8 100644
@@ -86,11 +86,6 @@ static int bmp280_spi_probe(struct spi_device *spi)
                                 spi->irq);
 }
 
-static int bmp280_spi_remove(struct spi_device *spi)
-{
-     return bmp280_common_remove(&spi->dev);
-}
-
 static const struct of_device_id bmp280_of_spi_match[] = {
      { .compatible = "bosch,bmp085", },
      { .compatible = "bosch,bmp180", },
@@ -118,7 +113,6 @@ static struct spi_driver bmp280_spi_driver = {
      },
      .id_table = bmp280_spi_id,
      .probe = bmp280_spi_probe,
-     .remove = bmp280_spi_remove,
 };
 module_spi_driver(bmp280_spi_driver);
 
drivers/iio/pressure/bmp280.h +0 -1
index eda50ef65706..57ba0e85db91 100644
@@ -112,7 +112,6 @@ int bmp280_common_probe(struct device *dev,
                      unsigned int chip,
                      const char *name,
                      int irq);
-int bmp280_common_remove(struct device *dev);
 
 /* PM ops */
 extern const struct dev_pm_ops bmp280_dev_pm_ops;  
#4 lore raw

wt., 22 paź 2019 o 12:15 Jonathan Cameron <[email protected]> napisał(a):

Quoted 24 lines
Quoted 20 lines · On Mon, 21 Oct 2019 14:47:18 +0200 Bartosz Golaszewski <[email protected]> wrote:

sob., 12 paź 2019 o 15:37 Jonathan Cameron <[email protected]> napisał(a):

Quoted 18 lines
Quoted 9 lines · On Mon, 7 Oct 2019 04:41:31 +0200 Bartosz Golaszewski <[email protected]> wrote:

From: Bartosz Golaszewski <[email protected]>

We can drop some duplicate code if we use devm_action for disabling regulators and pm and the managed variant of iio_device_register().

This allows us to completely remove all remove() callbacks from both i2c and spi code.

This is on top of the bulk regulator patch which is awaiting precusors getting to my upstream. I'll hold this one as well on that.

If it looks like I've forgotten it then give me a poke.

Quoted 9 lines
Quoted 4 lines

Hi Jonathan,

gentle poke after v5.4-rc4. Only one of the three patches is in next so far, the one using bulk regulators is missing too besides this one.

Thanks for the reminder.

Applied to the togreg branch of iio.git and pushed out as testing for the autobuilders to play with it.

Hi,

I don't see it in the togreg branch of the iio tree - did something go wrong with testing?

Bart

Quoted 210 lines

Thanks,

Jonathan

Quoted 206 lines

Best regards,
Bartosz Golaszewski

Quoted 202 lines

Thanks,

Jonathan

Quoted 197 lines

---
v1 -> v2:
- squash the patches using devm_iio_device_register() and devm_action to keep the changes bisectable

 drivers/iio/pressure/bmp280-core.c | 62 +++++++++++++++---------------
 drivers/iio/pressure/bmp280-i2c.c  |  6 ---
 drivers/iio/pressure/bmp280-spi.c  |  6 ---
 drivers/iio/pressure/bmp280.h      |  1 -
 4 files changed, 30 insertions(+), 45 deletions(-)
drivers/iio/pressure/bmp280-core.c +30 -32
index c2988dbdb1a7..79254dd26dfd 100644
@@ -984,6 +984,22 @@ static int bmp085_fetch_eoc_irq(struct device *dev,
      return 0;
 }
 
+static void bmp280_pm_disable(void *data)
+{
+     struct device *dev = data;
+
+     pm_runtime_get_sync(dev);
+     pm_runtime_put_noidle(dev);
+     pm_runtime_disable(dev);
+}
+
+static void bmp280_regulators_disable(void *data)
+{
+     struct regulator_bulk_data *supplies = data;
+
+     regulator_bulk_disable(BMP280_NUM_SUPPLIES, supplies);
+}
+
 int bmp280_common_probe(struct device *dev,
                      struct regmap *regmap,
                      unsigned int chip,
@@ -1055,6 +1071,11 @@ int bmp280_common_probe(struct device *dev,
              return ret;
      }
 
+     ret = devm_add_action_or_reset(dev, bmp280_regulators_disable,
+                                    data->supplies);
+     if (ret)
+             return ret;
+
      /* Wait to make sure we started up properly */
      usleep_range(data->start_up_time, data->start_up_time + 100);
 
@@ -1069,17 +1090,16 @@ int bmp280_common_probe(struct device *dev,
      data->regmap = regmap;
      ret = regmap_read(regmap, BMP280_REG_ID, &chip_id);
      if (ret < 0)
-             goto out_disable_regulators;
+             return ret;
      if (chip_id != chip) {
              dev_err(dev, "bad chip id: expected %x got %x\n",
                      chip, chip_id);
-             ret = -EINVAL;
-             goto out_disable_regulators;
+             return -EINVAL;
      }
 
      ret = data->chip_info->chip_config(data);
      if (ret < 0)
-             goto out_disable_regulators;
+             return ret;
 
      dev_set_drvdata(dev, indio_dev);
 
@@ -1093,14 +1113,14 @@ int bmp280_common_probe(struct device *dev,
              if (ret < 0) {
                      dev_err(data->dev,
                              "failed to read calibration coefficients\n");
-                     goto out_disable_regulators;
+                     return ret;
              }
      } else if (chip_id == BMP280_CHIP_ID || chip_id == BME280_CHIP_ID) {
              ret = bmp280_read_calib(data, &data->calib.bmp280, chip_id);
              if (ret < 0) {
                      dev_err(data->dev,
                              "failed to read calibration coefficients\n");
-                     goto out_disable_regulators;
+                     return ret;
              }
      }
 
@@ -1112,7 +1132,7 @@ int bmp280_common_probe(struct device *dev,
      if (irq > 0 || (chip_id  == BMP180_CHIP_ID)) {
              ret = bmp085_fetch_eoc_irq(dev, name, irq, data);
              if (ret)
-                     goto out_disable_regulators;
+                     return ret;
      }
 
      /* Enable runtime PM */
@@ -1127,36 +1147,14 @@ int bmp280_common_probe(struct device *dev,
      pm_runtime_use_autosuspend(dev);
      pm_runtime_put(dev);
 
-     ret = iio_device_register(indio_dev);
+     ret = devm_add_action_or_reset(dev, bmp280_pm_disable, dev);
      if (ret)
-             goto out_runtime_pm_disable;
-
-     return 0;
+             return ret;
 
-out_runtime_pm_disable:
-     pm_runtime_get_sync(data->dev);
-     pm_runtime_put_noidle(data->dev);
-     pm_runtime_disable(data->dev);
-out_disable_regulators:
-     regulator_bulk_disable(BMP280_NUM_SUPPLIES, data->supplies);
-     return ret;
+     return devm_iio_device_register(dev, indio_dev);
 }
 EXPORT_SYMBOL(bmp280_common_probe);
 
-int bmp280_common_remove(struct device *dev)
-{
-     struct iio_dev *indio_dev = dev_get_drvdata(dev);
-     struct bmp280_data *data = iio_priv(indio_dev);
-
-     iio_device_unregister(indio_dev);
-     pm_runtime_get_sync(data->dev);
-     pm_runtime_put_noidle(data->dev);
-     pm_runtime_disable(data->dev);
-     regulator_bulk_disable(BMP280_NUM_SUPPLIES, data->supplies);
-     return 0;
-}
-EXPORT_SYMBOL(bmp280_common_remove);
-
 #ifdef CONFIG_PM
 static int bmp280_runtime_suspend(struct device *dev)
 {
drivers/iio/pressure/bmp280-i2c.c +0 -6
index acd9a3784fb4..3109c8e2cc11 100644
@@ -38,11 +38,6 @@ static int bmp280_i2c_probe(struct i2c_client *client,
                                 client->irq);
 }
 
-static int bmp280_i2c_remove(struct i2c_client *client)
-{
-     return bmp280_common_remove(&client->dev);
-}
-
 static const struct acpi_device_id bmp280_acpi_i2c_match[] = {
      {"BMP0280", BMP280_CHIP_ID },
      {"BMP0180", BMP180_CHIP_ID },
@@ -82,7 +77,6 @@ static struct i2c_driver bmp280_i2c_driver = {
              .pm = &bmp280_dev_pm_ops,
      },
      .probe          = bmp280_i2c_probe,
-     .remove         = bmp280_i2c_remove,
      .id_table       = bmp280_i2c_id,
 };
 module_i2c_driver(bmp280_i2c_driver);
drivers/iio/pressure/bmp280-spi.c +0 -6
index 9d57b7a3b134..625b86878ad8 100644
@@ -86,11 +86,6 @@ static int bmp280_spi_probe(struct spi_device *spi)
                                 spi->irq);
 }
 
-static int bmp280_spi_remove(struct spi_device *spi)
-{
-     return bmp280_common_remove(&spi->dev);
-}
-
 static const struct of_device_id bmp280_of_spi_match[] = {
      { .compatible = "bosch,bmp085", },
      { .compatible = "bosch,bmp180", },
@@ -118,7 +113,6 @@ static struct spi_driver bmp280_spi_driver = {
      },
      .id_table = bmp280_spi_id,
      .probe = bmp280_spi_probe,
-     .remove = bmp280_spi_remove,
 };
 module_spi_driver(bmp280_spi_driver);
 
drivers/iio/pressure/bmp280.h +0 -1
index eda50ef65706..57ba0e85db91 100644
@@ -112,7 +112,6 @@ int bmp280_common_probe(struct device *dev,
                      unsigned int chip,
                      const char *name,
                      int irq);
-int bmp280_common_remove(struct device *dev);
 
 /* PM ops */
 extern const struct dev_pm_ops bmp280_dev_pm_ops;
maintainer
#5 lore raw
Quoted 31 lines · On Thu, 31 Oct 2019 07:46:51 +0100 Bartosz Golaszewski <[email protected]> wrote:

wt., 22 paź 2019 o 12:15 Jonathan Cameron <[email protected]> napisał(a):

Quoted 30 lines
Quoted 17 lines · On Mon, 21 Oct 2019 14:47:18 +0200 Bartosz Golaszewski <[email protected]> wrote:

sob., 12 paź 2019 o 15:37 Jonathan Cameron <[email protected]> napisał(a):

Quoted 16 lines
Quoted 9 lines · On Mon, 7 Oct 2019 04:41:31 +0200 Bartosz Golaszewski <[email protected]> wrote:

From: Bartosz Golaszewski <[email protected]>

We can drop some duplicate code if we use devm_action for disabling regulators and pm and the managed variant of iio_device_register().

This allows us to completely remove all remove() callbacks from both i2c and spi code.

This is on top of the bulk regulator patch which is awaiting precusors getting to my upstream. I'll hold this one as well on that.

Quoted 7 lines
Quoted 2 lines

If it looks like I've forgotten it then give me a poke.

Hi Jonathan,

gentle poke after v5.4-rc4. Only one of the three patches is in next so far, the one using bulk regulators is missing too besides this one.

Thanks for the reminder.

Quoted 8 lines
Quoted 3 lines

Applied to the togreg branch of iio.git and pushed out as testing for the autobuilders to play with it.

Hi,

I don't see it in the togreg branch of the iio tree - did something go wrong with testing?

I tend to only get to my laptop ever few days + 0-day has taken to timing out half the time at the moment (which means you end up waiting another day for late running tests to complete). So can be a week or more before things
make it to the togreg branch. Sometimes I forget entirely and it only
happens when I get a pull request ready.

Anyhow, should be in Greg's tree and linux-next by now.

Thanks,

Jonathan

Quoted 213 lines

Bart

Quoted 210 lines

Thanks,

Jonathan

Quoted 206 lines

Best regards,
Bartosz Golaszewski

Quoted 202 lines

Thanks,

Jonathan

Quoted 197 lines

---
v1 -> v2:
- squash the patches using devm_iio_device_register() and devm_action to keep the changes bisectable

 drivers/iio/pressure/bmp280-core.c | 62 +++++++++++++++---------------
 drivers/iio/pressure/bmp280-i2c.c  |  6 ---
 drivers/iio/pressure/bmp280-spi.c  |  6 ---
 drivers/iio/pressure/bmp280.h      |  1 -
 4 files changed, 30 insertions(+), 45 deletions(-)
drivers/iio/pressure/bmp280-core.c +30 -32
index c2988dbdb1a7..79254dd26dfd 100644
@@ -984,6 +984,22 @@ static int bmp085_fetch_eoc_irq(struct device *dev,
      return 0;
 }
 
+static void bmp280_pm_disable(void *data)
+{
+     struct device *dev = data;
+
+     pm_runtime_get_sync(dev);
+     pm_runtime_put_noidle(dev);
+     pm_runtime_disable(dev);
+}
+
+static void bmp280_regulators_disable(void *data)
+{
+     struct regulator_bulk_data *supplies = data;
+
+     regulator_bulk_disable(BMP280_NUM_SUPPLIES, supplies);
+}
+
 int bmp280_common_probe(struct device *dev,
                      struct regmap *regmap,
                      unsigned int chip,
@@ -1055,6 +1071,11 @@ int bmp280_common_probe(struct device *dev,
              return ret;
      }
 
+     ret = devm_add_action_or_reset(dev, bmp280_regulators_disable,
+                                    data->supplies);
+     if (ret)
+             return ret;
+
      /* Wait to make sure we started up properly */
      usleep_range(data->start_up_time, data->start_up_time + 100);
 
@@ -1069,17 +1090,16 @@ int bmp280_common_probe(struct device *dev,
      data->regmap = regmap;
      ret = regmap_read(regmap, BMP280_REG_ID, &chip_id);
      if (ret < 0)
-             goto out_disable_regulators;
+             return ret;
      if (chip_id != chip) {
              dev_err(dev, "bad chip id: expected %x got %x\n",
                      chip, chip_id);
-             ret = -EINVAL;
-             goto out_disable_regulators;
+             return -EINVAL;
      }
 
      ret = data->chip_info->chip_config(data);
      if (ret < 0)
-             goto out_disable_regulators;
+             return ret;
 
      dev_set_drvdata(dev, indio_dev);
 
@@ -1093,14 +1113,14 @@ int bmp280_common_probe(struct device *dev,
              if (ret < 0) {
                      dev_err(data->dev,
                              "failed to read calibration coefficients\n");
-                     goto out_disable_regulators;
+                     return ret;
              }
      } else if (chip_id == BMP280_CHIP_ID || chip_id == BME280_CHIP_ID) {
              ret = bmp280_read_calib(data, &data->calib.bmp280, chip_id);
              if (ret < 0) {
                      dev_err(data->dev,
                              "failed to read calibration coefficients\n");
-                     goto out_disable_regulators;
+                     return ret;
              }
      }
 
@@ -1112,7 +1132,7 @@ int bmp280_common_probe(struct device *dev,
      if (irq > 0 || (chip_id  == BMP180_CHIP_ID)) {
              ret = bmp085_fetch_eoc_irq(dev, name, irq, data);
              if (ret)
-                     goto out_disable_regulators;
+                     return ret;
      }
 
      /* Enable runtime PM */
@@ -1127,36 +1147,14 @@ int bmp280_common_probe(struct device *dev,
      pm_runtime_use_autosuspend(dev);
      pm_runtime_put(dev);
 
-     ret = iio_device_register(indio_dev);
+     ret = devm_add_action_or_reset(dev, bmp280_pm_disable, dev);
      if (ret)
-             goto out_runtime_pm_disable;
-
-     return 0;
+             return ret;
 
-out_runtime_pm_disable:
-     pm_runtime_get_sync(data->dev);
-     pm_runtime_put_noidle(data->dev);
-     pm_runtime_disable(data->dev);
-out_disable_regulators:
-     regulator_bulk_disable(BMP280_NUM_SUPPLIES, data->supplies);
-     return ret;
+     return devm_iio_device_register(dev, indio_dev);
 }
 EXPORT_SYMBOL(bmp280_common_probe);
 
-int bmp280_common_remove(struct device *dev)
-{
-     struct iio_dev *indio_dev = dev_get_drvdata(dev);
-     struct bmp280_data *data = iio_priv(indio_dev);
-
-     iio_device_unregister(indio_dev);
-     pm_runtime_get_sync(data->dev);
-     pm_runtime_put_noidle(data->dev);
-     pm_runtime_disable(data->dev);
-     regulator_bulk_disable(BMP280_NUM_SUPPLIES, data->supplies);
-     return 0;
-}
-EXPORT_SYMBOL(bmp280_common_remove);
-
 #ifdef CONFIG_PM
 static int bmp280_runtime_suspend(struct device *dev)
 {
drivers/iio/pressure/bmp280-i2c.c +0 -6
index acd9a3784fb4..3109c8e2cc11 100644
@@ -38,11 +38,6 @@ static int bmp280_i2c_probe(struct i2c_client *client,
                                 client->irq);
 }
 
-static int bmp280_i2c_remove(struct i2c_client *client)
-{
-     return bmp280_common_remove(&client->dev);
-}
-
 static const struct acpi_device_id bmp280_acpi_i2c_match[] = {
      {"BMP0280", BMP280_CHIP_ID },
      {"BMP0180", BMP180_CHIP_ID },
@@ -82,7 +77,6 @@ static struct i2c_driver bmp280_i2c_driver = {
              .pm = &bmp280_dev_pm_ops,
      },
      .probe          = bmp280_i2c_probe,
-     .remove         = bmp280_i2c_remove,
      .id_table       = bmp280_i2c_id,
 };
 module_i2c_driver(bmp280_i2c_driver);
drivers/iio/pressure/bmp280-spi.c +0 -6
index 9d57b7a3b134..625b86878ad8 100644
@@ -86,11 +86,6 @@ static int bmp280_spi_probe(struct spi_device *spi)
                                 spi->irq);
 }
 
-static int bmp280_spi_remove(struct spi_device *spi)
-{
-     return bmp280_common_remove(&spi->dev);
-}
-
 static const struct of_device_id bmp280_of_spi_match[] = {
      { .compatible = "bosch,bmp085", },
      { .compatible = "bosch,bmp180", },
@@ -118,7 +113,6 @@ static struct spi_driver bmp280_spi_driver = {
      },
      .id_table = bmp280_spi_id,
      .probe = bmp280_spi_probe,
-     .remove = bmp280_spi_remove,
 };
 module_spi_driver(bmp280_spi_driver);
 
drivers/iio/pressure/bmp280.h +0 -1
index eda50ef65706..57ba0e85db91 100644
@@ -112,7 +112,6 @@ int bmp280_common_probe(struct device *dev,
                      unsigned int chip,
                      const char *name,
                      int irq);
-int bmp280_common_remove(struct device *dev);
 
 /* PM ops */
 extern const struct dev_pm_ops bmp280_dev_pm_ops;