Skip to contentSkip to conversation

ARM: dts: imx6qdl-sabreauto: Fix storm of accelerometer interrupts

PATCH Applied Fabio Estevam 3 participants 5 messages Oct 9, 2019 – Oct 26, 2019

Subsystems (2)
lore
Share & tools
lore

Fabio Estevam

author reviewer
#0 lore raw

PATCH 1/1 ARM: dts: imx6qdl-sabreauto: Fix storm of accelerometer interrupts

Since commit a211b8c55f3c ("ARM: dts: imx6qdl-sabreauto: Add sensors") a storm of accelerometer interrupts is seen:

[  114.211283] irq 260: nobody cared (try booting with the "irqpoll" option)
[  114.218108] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.3.4 #1
[  114.223960] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[  114.230531] [<c0112858>] (unwind_backtrace) from [<c010cdc8>] (show_stack+0x10/0x14)
[  114.238301] [<c010cdc8>] (show_stack) from [<c0c1aa1c>] (dump_stack+0xd8/0x110)
[  114.245644] [<c0c1aa1c>] (dump_stack) from [<c0193594>] (__report_bad_irq+0x30/0xc0)
[  114.253417] [<c0193594>] (__report_bad_irq) from [<c01933ac>] (note_interrupt+0x108/0x298)
[  114.261707] [<c01933ac>] (note_interrupt) from [<c018ffe4>] (handle_irq_event_percpu+0x70/0x80)
[  114.270433] [<c018ffe4>] (handle_irq_event_percpu) from [<c019002c>] (handle_irq_event+0x38/0x5c)
[  114.279326] [<c019002c>] (handle_irq_event) from [<c019438c>] (handle_level_irq+0xc8/0x154)
[  114.287701] [<c019438c>] (handle_level_irq) from [<c018eda0>] (generic_handle_irq+0x20/0x34)
[  114.296166] [<c018eda0>] (generic_handle_irq) from [<c0534214>] (mxc_gpio_irq_handler+0x30/0xf0)
[  114.304975] [<c0534214>] (mxc_gpio_irq_handler) from [<c0534334>] (mx3_gpio_irq_handler+0x60/0xb0)
[  114.313955] [<c0534334>] (mx3_gpio_irq_handler) from [<c018eda0>] (generic_handle_irq+0x20/0x34)
[  114.322762] [<c018eda0>] (generic_handle_irq) from [<c018f3ac>] (__handle_domain_irq+0x64/0xe0)
[  114.331485] [<c018f3ac>] (__handle_domain_irq) from [<c05215a8>] (gic_handle_irq+0x4c/0xa8)
[  114.339862] [<c05215a8>] (gic_handle_irq) from [<c0101a70>] (__irq_svc+0x70/0x98)
[  114.347361] Exception stack(0xc1301ec0 to 0xc1301f08)
[  114.352435] 1ec0: 00000001 00000006 00000000 c130c340 00000001 c130f688 9785636d c13ea2e8
[  114.360635] 1ee0: 9784907d 0000001a eaf99d78 0000001a 00000000 c1301f10 c0182b00 c0878de4
[  114.368830] 1f00: 20000013 ffffffff
[  114.372349] [<c0101a70>] (__irq_svc) from [<c0878de4>] (cpuidle_enter_state+0x168/0x5f4)
[  114.380464] [<c0878de4>] (cpuidle_enter_state) from [<c08792ac>] (cpuidle_enter+0x28/0x38)
[  114.388751] [<c08792ac>] (cpuidle_enter) from [<c015ef9c>] (do_idle+0x224/0x2a8)
[  114.396168] [<c015ef9c>] (do_idle) from [<c015f3b8>] (cpu_startup_entry+0x18/0x20)
[  114.403765] [<c015f3b8>] (cpu_startup_entry) from [<c1200e54>] (start_kernel+0x43c/0x500)
[  114.411958] handlers:
[  114.414302] [<a01028b8>] irq_default_primary_handler threaded [<fd7a3b08>] mma8452_interrupt
[  114.422974] Disabling IRQ #260
# cat /proc/interrupts 
           CPU0       CPU1       
....
260:     100001          0  gpio-mxc  31 Level     mma8451

The MMA8451 interrupt triggers as low level, so the GPIO6_IO31 pin needs to activate its pull up, otherwise it will stay always at low level generating multiple interrupts.

The current device tree does not configure the IOMUX for this pin, so it uses whathever comes configured from the bootloader.

The IOMUXC_SW_PAD_CTL_PAD_EIM_BCLK register value comes as 0x8000 from the bootloader, which has PKE bit cleared, hence disabling the pull-up.

Instead of relying on a previous configuration from the bootloader, configure the GPIO6_IO31 pin with pull-up enabled in order to fix this problem.

Fixes a211b8c55f3c ("ARM: dts: imx6qdl-sabreauto: Add sensors")
---
 arch/arm/boot/dts/imx6qdl-sabreauto.dtsi | 8 ++++++++
 1 file changed, 8 insertions(+)
arch/arm/boot/dts/imx6qdl-sabreauto.dtsi +8 -0
index f3404dd10537..cf628465cd0a 100644
@@ -230,6 +230,8 @@
 			accelerometer@1c {
 				compatible = "fsl,mma8451";
 				reg = <0x1c>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_mma8451_int>;
 				interrupt-parent = <&gpio6>;
 				interrupts = <31 IRQ_TYPE_LEVEL_LOW>;
 			};
@@ -628,6 +630,12 @@
 			>;
 		};
 
+		pinctrl_mma8451_int: mma8451intgrp {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_BCLK__GPIO6_IO31		0xb0b1
+			>;
+		};
+
 		pinctrl_pwm3: pwm1grp {
 			fsl,pins = <
 				MX6QDL_PAD_SD4_DAT1__PWM3_OUT		0x1b0b1
Signature · 7 lines
2.17.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#1 lore raw

@Leonard, comment?

Shawn

Quoted 88 lines · Fabio Estevam

Since commit a211b8c55f3c ("ARM: dts: imx6qdl-sabreauto: Add sensors") a storm of accelerometer interrupts is seen:

[  114.211283] irq 260: nobody cared (try booting with the "irqpoll" option)
[  114.218108] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.3.4 #1
[  114.223960] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[  114.230531] [<c0112858>] (unwind_backtrace) from [<c010cdc8>] (show_stack+0x10/0x14)
[  114.238301] [<c010cdc8>] (show_stack) from [<c0c1aa1c>] (dump_stack+0xd8/0x110)
[  114.245644] [<c0c1aa1c>] (dump_stack) from [<c0193594>] (__report_bad_irq+0x30/0xc0)
[  114.253417] [<c0193594>] (__report_bad_irq) from [<c01933ac>] (note_interrupt+0x108/0x298)
[  114.261707] [<c01933ac>] (note_interrupt) from [<c018ffe4>] (handle_irq_event_percpu+0x70/0x80)
[  114.270433] [<c018ffe4>] (handle_irq_event_percpu) from [<c019002c>] (handle_irq_event+0x38/0x5c)
[  114.279326] [<c019002c>] (handle_irq_event) from [<c019438c>] (handle_level_irq+0xc8/0x154)
[  114.287701] [<c019438c>] (handle_level_irq) from [<c018eda0>] (generic_handle_irq+0x20/0x34)
[  114.296166] [<c018eda0>] (generic_handle_irq) from [<c0534214>] (mxc_gpio_irq_handler+0x30/0xf0)
[  114.304975] [<c0534214>] (mxc_gpio_irq_handler) from [<c0534334>] (mx3_gpio_irq_handler+0x60/0xb0)
[  114.313955] [<c0534334>] (mx3_gpio_irq_handler) from [<c018eda0>] (generic_handle_irq+0x20/0x34)
[  114.322762] [<c018eda0>] (generic_handle_irq) from [<c018f3ac>] (__handle_domain_irq+0x64/0xe0)
[  114.331485] [<c018f3ac>] (__handle_domain_irq) from [<c05215a8>] (gic_handle_irq+0x4c/0xa8)
[  114.339862] [<c05215a8>] (gic_handle_irq) from [<c0101a70>] (__irq_svc+0x70/0x98)
[  114.347361] Exception stack(0xc1301ec0 to 0xc1301f08)
[  114.352435] 1ec0: 00000001 00000006 00000000 c130c340 00000001 c130f688 9785636d c13ea2e8
[  114.360635] 1ee0: 9784907d 0000001a eaf99d78 0000001a 00000000 c1301f10 c0182b00 c0878de4
[  114.368830] 1f00: 20000013 ffffffff
[  114.372349] [<c0101a70>] (__irq_svc) from [<c0878de4>] (cpuidle_enter_state+0x168/0x5f4)
[  114.380464] [<c0878de4>] (cpuidle_enter_state) from [<c08792ac>] (cpuidle_enter+0x28/0x38)
[  114.388751] [<c08792ac>] (cpuidle_enter) from [<c015ef9c>] (do_idle+0x224/0x2a8)
[  114.396168] [<c015ef9c>] (do_idle) from [<c015f3b8>] (cpu_startup_entry+0x18/0x20)
[  114.403765] [<c015f3b8>] (cpu_startup_entry) from [<c1200e54>] (start_kernel+0x43c/0x500)
[  114.411958] handlers:
[  114.414302] [<a01028b8>] irq_default_primary_handler threaded [<fd7a3b08>] mma8452_interrupt
[  114.422974] Disabling IRQ #260
# cat /proc/interrupts 
           CPU0       CPU1       
....
260:     100001          0  gpio-mxc  31 Level     mma8451

The MMA8451 interrupt triggers as low level, so the GPIO6_IO31 pin needs to activate its pull up, otherwise it will stay always at low level generating multiple interrupts.

The current device tree does not configure the IOMUX for this pin, so it uses whathever comes configured from the bootloader.

The IOMUXC_SW_PAD_CTL_PAD_EIM_BCLK register value comes as 0x8000 from the bootloader, which has PKE bit cleared, hence disabling the pull-up.

Instead of relying on a previous configuration from the bootloader, configure the GPIO6_IO31 pin with pull-up enabled in order to fix this problem.

Fixes a211b8c55f3c ("ARM: dts: imx6qdl-sabreauto: Add sensors")
---
 arch/arm/boot/dts/imx6qdl-sabreauto.dtsi | 8 ++++++++
 1 file changed, 8 insertions(+)
arch/arm/boot/dts/imx6qdl-sabreauto.dtsi +8 -0
index f3404dd10537..cf628465cd0a 100644
@@ -230,6 +230,8 @@
 			accelerometer@1c {
 				compatible = "fsl,mma8451";
 				reg = <0x1c>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_mma8451_int>;
 				interrupt-parent = <&gpio6>;
 				interrupts = <31 IRQ_TYPE_LEVEL_LOW>;
 			};
@@ -628,6 +630,12 @@
 			>;
 		};
 
+		pinctrl_mma8451_int: mma8451intgrp {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_BCLK__GPIO6_IO31		0xb0b1
+			>;
+		};
+
 		pinctrl_pwm3: pwm1grp {
 			fsl,pins = <
 				MX6QDL_PAD_SD4_DAT1__PWM3_OUT		0x1b0b1
Signature · 1 line
2.17.1

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Reviewed-by
#2 lore raw
Quoted 1 line · Shawn Guo

@Leonard, comment?

This worked fine for me but after a bit of digging I was able to reproduce by using upstream uboot:

     U-Boot 2019.10-00181-g17fd9915a4c6 (Oct 25 2019 - 17:28:28 +0300)
     ...
     0x020E0158:  00000000
     0x020E046C:  0000B0B1

versus:

     U-Boot 2019.04-00890-g6a5534d13b9e (Oct 25 2019 - 18:56:40 +0300)
     ...
     0x020E0158:  00000005
     0x020E046C:  0000B0B1

But apparently what I reproduced was due to incorrect mux? Fabio: what is your exact bootloader?

Anyway, as far as I understand explicitly configuring pins is preferable to relying on bootloader anyway.

Quoted 79 lines

Shawn

Quoted 76 lines · Fabio Estevam

Since commit a211b8c55f3c ("ARM: dts: imx6qdl-sabreauto: Add sensors") a storm of accelerometer interrupts is seen:

[  114.211283] irq 260: nobody cared (try booting with the "irqpoll" option)
[  114.218108] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.3.4 #1
[  114.223960] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[  114.230531] [<c0112858>] (unwind_backtrace) from [<c010cdc8>] (show_stack+0x10/0x14)
[  114.238301] [<c010cdc8>] (show_stack) from [<c0c1aa1c>] (dump_stack+0xd8/0x110)
[  114.245644] [<c0c1aa1c>] (dump_stack) from [<c0193594>] (__report_bad_irq+0x30/0xc0)
[  114.253417] [<c0193594>] (__report_bad_irq) from [<c01933ac>] (note_interrupt+0x108/0x298)
[  114.261707] [<c01933ac>] (note_interrupt) from [<c018ffe4>] (handle_irq_event_percpu+0x70/0x80)
[  114.270433] [<c018ffe4>] (handle_irq_event_percpu) from [<c019002c>] (handle_irq_event+0x38/0x5c)
[  114.279326] [<c019002c>] (handle_irq_event) from [<c019438c>] (handle_level_irq+0xc8/0x154)
[  114.287701] [<c019438c>] (handle_level_irq) from [<c018eda0>] (generic_handle_irq+0x20/0x34)
[  114.296166] [<c018eda0>] (generic_handle_irq) from [<c0534214>] (mxc_gpio_irq_handler+0x30/0xf0)
[  114.304975] [<c0534214>] (mxc_gpio_irq_handler) from [<c0534334>] (mx3_gpio_irq_handler+0x60/0xb0)
[  114.313955] [<c0534334>] (mx3_gpio_irq_handler) from [<c018eda0>] (generic_handle_irq+0x20/0x34)
[  114.322762] [<c018eda0>] (generic_handle_irq) from [<c018f3ac>] (__handle_domain_irq+0x64/0xe0)
[  114.331485] [<c018f3ac>] (__handle_domain_irq) from [<c05215a8>] (gic_handle_irq+0x4c/0xa8)
[  114.339862] [<c05215a8>] (gic_handle_irq) from [<c0101a70>] (__irq_svc+0x70/0x98)
[  114.347361] Exception stack(0xc1301ec0 to 0xc1301f08)
[  114.352435] 1ec0: 00000001 00000006 00000000 c130c340 00000001 c130f688 9785636d c13ea2e8
[  114.360635] 1ee0: 9784907d 0000001a eaf99d78 0000001a 00000000 c1301f10 c0182b00 c0878de4
[  114.368830] 1f00: 20000013 ffffffff
[  114.372349] [<c0101a70>] (__irq_svc) from [<c0878de4>] (cpuidle_enter_state+0x168/0x5f4)
[  114.380464] [<c0878de4>] (cpuidle_enter_state) from [<c08792ac>] (cpuidle_enter+0x28/0x38)
[  114.388751] [<c08792ac>] (cpuidle_enter) from [<c015ef9c>] (do_idle+0x224/0x2a8)
[  114.396168] [<c015ef9c>] (do_idle) from [<c015f3b8>] (cpu_startup_entry+0x18/0x20)
[  114.403765] [<c015f3b8>] (cpu_startup_entry) from [<c1200e54>] (start_kernel+0x43c/0x500)
[  114.411958] handlers:
[  114.414302] [<a01028b8>] irq_default_primary_handler threaded [<fd7a3b08>] mma8452_interrupt
[  114.422974] Disabling IRQ #260
# cat /proc/interrupts
            CPU0       CPU1
....
260:     100001          0  gpio-mxc  31 Level     mma8451

The MMA8451 interrupt triggers as low level, so the GPIO6_IO31 pin needs to activate its pull up, otherwise it will stay always at low level generating multiple interrupts.

The current device tree does not configure the IOMUX for this pin, so it uses whathever comes configured from the bootloader.

The IOMUXC_SW_PAD_CTL_PAD_EIM_BCLK register value comes as 0x8000 from the bootloader, which has PKE bit cleared, hence disabling the pull-up.

Instead of relying on a previous configuration from the bootloader, configure the GPIO6_IO31 pin with pull-up enabled in order to fix this problem.

Fixes a211b8c55f3c ("ARM: dts: imx6qdl-sabreauto: Add sensors")
---
  arch/arm/boot/dts/imx6qdl-sabreauto.dtsi | 8 ++++++++
  1 file changed, 8 insertions(+)
arch/arm/boot/dts/imx6qdl-sabreauto.dtsi +2 -0
index f3404dd10537..cf628465cd0a 100644
@@ -230,6 +230,8 @@
  			accelerometer@1c {
  				compatible = "fsl,mma8451";
  				reg = <0x1c>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_mma8451_int>;
  				interrupt-parent = <&gpio6>;
  				interrupts = <31 IRQ_TYPE_LEVEL_LOW>;
  			};
@@ -628,6 +630,12 @@
  			>;
  		};
 
Quoted 13 lines
Quoted 12 lines
arch/arm/boot/dts/imx6qdl-sabreauto.dtsi +6 -0
+		pinctrl_mma8451_int: mma8451intgrp {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_BCLK__GPIO6_IO31		0xb0b1
+			>;
+		};
+
  		pinctrl_pwm3: pwm1grp {
  			fsl,pins = <
  				MX6QDL_PAD_SD4_DAT1__PWM3_OUT		0x1b0b1
Signature · 1 line
2.17.1

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

author reviewer
#3 lore raw

Hi Leonard,

Quoted 14 lines · Leonard Crestez
Quoted 1 line · Shawn Guo

@Leonard, comment?

This worked fine for me but after a bit of digging I was able to reproduce by using upstream uboot:

     U-Boot 2019.10-00181-g17fd9915a4c6 (Oct 25 2019 - 17:28:28 +0300)
     ...
     0x020E0158:  00000000
     0x020E046C:  0000B0B1

versus:

Quoted 7 lines
     U-Boot 2019.04-00890-g6a5534d13b9e (Oct 25 2019 - 18:56:40 +0300)
     ...
     0x020E0158:  00000005
     0x020E046C:  0000B0B1

But apparently what I reproduced was due to incorrect mux? Fabio: what is your exact bootloader?

I used mainline U-Boot 2019.10.

Quoted 5 lines

Anyway, as far as I understand explicitly configuring pins is preferable to relying on bootloader anyway.

Thanks

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Applied
#4 lore raw
In reply to Fabio Estevam
Quoted 49 lines · Fabio Estevam

Since commit a211b8c55f3c ("ARM: dts: imx6qdl-sabreauto: Add sensors") a storm of accelerometer interrupts is seen:

[  114.211283] irq 260: nobody cared (try booting with the "irqpoll" option)
[  114.218108] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.3.4 #1
[  114.223960] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[  114.230531] [<c0112858>] (unwind_backtrace) from [<c010cdc8>] (show_stack+0x10/0x14)
[  114.238301] [<c010cdc8>] (show_stack) from [<c0c1aa1c>] (dump_stack+0xd8/0x110)
[  114.245644] [<c0c1aa1c>] (dump_stack) from [<c0193594>] (__report_bad_irq+0x30/0xc0)
[  114.253417] [<c0193594>] (__report_bad_irq) from [<c01933ac>] (note_interrupt+0x108/0x298)
[  114.261707] [<c01933ac>] (note_interrupt) from [<c018ffe4>] (handle_irq_event_percpu+0x70/0x80)
[  114.270433] [<c018ffe4>] (handle_irq_event_percpu) from [<c019002c>] (handle_irq_event+0x38/0x5c)
[  114.279326] [<c019002c>] (handle_irq_event) from [<c019438c>] (handle_level_irq+0xc8/0x154)
[  114.287701] [<c019438c>] (handle_level_irq) from [<c018eda0>] (generic_handle_irq+0x20/0x34)
[  114.296166] [<c018eda0>] (generic_handle_irq) from [<c0534214>] (mxc_gpio_irq_handler+0x30/0xf0)
[  114.304975] [<c0534214>] (mxc_gpio_irq_handler) from [<c0534334>] (mx3_gpio_irq_handler+0x60/0xb0)
[  114.313955] [<c0534334>] (mx3_gpio_irq_handler) from [<c018eda0>] (generic_handle_irq+0x20/0x34)
[  114.322762] [<c018eda0>] (generic_handle_irq) from [<c018f3ac>] (__handle_domain_irq+0x64/0xe0)
[  114.331485] [<c018f3ac>] (__handle_domain_irq) from [<c05215a8>] (gic_handle_irq+0x4c/0xa8)
[  114.339862] [<c05215a8>] (gic_handle_irq) from [<c0101a70>] (__irq_svc+0x70/0x98)
[  114.347361] Exception stack(0xc1301ec0 to 0xc1301f08)
[  114.352435] 1ec0: 00000001 00000006 00000000 c130c340 00000001 c130f688 9785636d c13ea2e8
[  114.360635] 1ee0: 9784907d 0000001a eaf99d78 0000001a 00000000 c1301f10 c0182b00 c0878de4
[  114.368830] 1f00: 20000013 ffffffff
[  114.372349] [<c0101a70>] (__irq_svc) from [<c0878de4>] (cpuidle_enter_state+0x168/0x5f4)
[  114.380464] [<c0878de4>] (cpuidle_enter_state) from [<c08792ac>] (cpuidle_enter+0x28/0x38)
[  114.388751] [<c08792ac>] (cpuidle_enter) from [<c015ef9c>] (do_idle+0x224/0x2a8)
[  114.396168] [<c015ef9c>] (do_idle) from [<c015f3b8>] (cpu_startup_entry+0x18/0x20)
[  114.403765] [<c015f3b8>] (cpu_startup_entry) from [<c1200e54>] (start_kernel+0x43c/0x500)
[  114.411958] handlers:
[  114.414302] [<a01028b8>] irq_default_primary_handler threaded [<fd7a3b08>] mma8452_interrupt
[  114.422974] Disabling IRQ #260
# cat /proc/interrupts 
           CPU0       CPU1       
....
260:     100001          0  gpio-mxc  31 Level     mma8451

The MMA8451 interrupt triggers as low level, so the GPIO6_IO31 pin needs to activate its pull up, otherwise it will stay always at low level generating multiple interrupts.

The current device tree does not configure the IOMUX for this pin, so it uses whathever comes configured from the bootloader.

The IOMUXC_SW_PAD_CTL_PAD_EIM_BCLK register value comes as 0x8000 from the bootloader, which has PKE bit cleared, hence disabling the pull-up.

Quoted 6 lines

Instead of relying on a previous configuration from the bootloader, configure the GPIO6_IO31 pin with pull-up enabled in order to fix this problem.

Fixes a211b8c55f3c ("ARM: dts: imx6qdl-sabreauto: Add sensors")

Applied, thanks.

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel