Skip to contentSkip to conversation

gpiolib: don't clear FLAG_IS_OUT when emulating open-drain/open-source

PATCH Applied Bartosz Golaszewski 2 participants 2 messages Oct 14, 2019

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 gpiolib: don't clear FLAG_IS_OUT when emulating open-drain/open-source

From: Bartosz Golaszewski <[email protected]>

When emulating open-drain/open-source by not actively driving the output lines - we're simply changing their mode to input. This is wrong as it will then make it impossible to change the value of such line - it's now considered to actually be in input mode. If we want to still use the direction_input() callback for simplicity then we need to set FLAG_IS_OUT manually in gpiod_direction_output() and not clear it in gpio_set_open_drain_value_commit() and gpio_set_open_source_value_commit().

Fixes c663e5f56737 ("gpio: support native single-ended hardware drivers")
[Bartosz: backported to v5.3, v4.19]
---
 drivers/gpio/gpiolib.c | 27 +++++++++++++++++++--------
 1 file changed, 19 insertions(+), 8 deletions(-)
drivers/gpio/gpiolib.c +19 -8
index e4203c1eb869..74a77001b1bd 100644
@@ -2775,8 +2775,10 @@ int gpiod_direction_output(struct gpio_desc *desc, int value)
 		if (!ret)
 			goto set_output_value;
 		/* Emulate open drain by not actively driving the line high */
-		if (value)
-			return gpiod_direction_input(desc);
+		if (value) {
+			ret = gpiod_direction_input(desc);
+			goto set_output_flag;
+		}
 	}
 	else if (test_bit(FLAG_OPEN_SOURCE, &desc->flags)) {
 		ret = gpio_set_config(gc, gpio_chip_hwgpio(desc),
@@ -2784,8 +2786,10 @@ int gpiod_direction_output(struct gpio_desc *desc, int value)
 		if (!ret)
 			goto set_output_value;
 		/* Emulate open source by not actively driving the line low */
-		if (!value)
-			return gpiod_direction_input(desc);
+		if (!value) {
+			ret = gpiod_direction_input(desc);
+			goto set_output_flag;
+		}
 	} else {
 		gpio_set_config(gc, gpio_chip_hwgpio(desc),
 				PIN_CONFIG_DRIVE_PUSH_PULL);
@@ -2793,6 +2797,17 @@ int gpiod_direction_output(struct gpio_desc *desc, int value)
 
 set_output_value:
 	return gpiod_direction_output_raw_commit(desc, value);
+
+set_output_flag:
+	/*
+	 * When emulating open-source or open-drain functionalities by not
+	 * actively driving the line (setting mode to input) we still need to
+	 * set the IS_OUT flag or otherwise we won't be able to set the line
+	 * value anymore.
+	 */
+	if (ret == 0)
+		set_bit(FLAG_IS_OUT, &desc->flags);
+	return ret;
 }
 EXPORT_SYMBOL_GPL(gpiod_direction_output);
 
@@ -3153,8 +3168,6 @@ static void gpio_set_open_drain_value_commit(struct gpio_desc *desc, bool value)
 
 	if (value) {
 		err = chip->direction_input(chip, offset);
-		if (!err)
-			clear_bit(FLAG_IS_OUT, &desc->flags);
 	} else {
 		err = chip->direction_output(chip, offset, 0);
 		if (!err)
@@ -3184,8 +3197,6 @@ static void gpio_set_open_source_value_commit(struct gpio_desc *desc, bool value
 			set_bit(FLAG_IS_OUT, &desc->flags);
 	} else {
 		err = chip->direction_input(chip, offset);
-		if (!err)
-			clear_bit(FLAG_IS_OUT, &desc->flags);
 	}
 	trace_gpio_direction(desc_to_gpio(desc), !value, err);
 	if (err < 0)
Signature · 1 line
2.23.0
maintainer Applied
#1 lore raw
Quoted 11 lines · Bartosz Golaszewski

From: Bartosz Golaszewski <[email protected]>

When emulating open-drain/open-source by not actively driving the output lines - we're simply changing their mode to input. This is wrong as it will then make it impossible to change the value of such line - it's now considered to actually be in input mode. If we want to still use the direction_input() callback for simplicity then we need to set FLAG_IS_OUT manually in gpiod_direction_output() and not clear it in gpio_set_open_drain_value_commit() and gpio_set_open_source_value_commit().

Quoted 6 lines
Fixes c663e5f56737 ("gpio: support native single-ended hardware drivers")
[Bartosz: backported to v5.3, v4.19]

I've queued this and the 4.14 patch, thanks!

Signature · 2 lines
Thanks,
Sasha