Skip to contentSkip to conversation

arm: dts: rk3399-rockpro64: sync dts from linux kernel

PATCH New Soeren Moch 3 participants 11 messages Nov 7, 2019 – Nov 18, 2019 Arm (32-bit)

lore
Share & tools
lore
#0 lore raw

PATCH 1/2 arm: dts: rk3399-rockpro64: sync dts from linux kernel

The most important change for u-boot is the fix for the vdd-log pwm voltage regulator to avoid overvoltage for the VD_LOGIC power domain.

---
Cc: Kever Yang <[email protected]>
Cc: u-boot at lists.denx.de

---
 arch/arm/dts/rk3399-rockpro64.dts | 57 ++++++++++++++++++++++++++-----
 1 file changed, 49 insertions(+), 8 deletions(-)
arch/arm/dts/rk3399-rockpro64.dts +49 -8
index 1f2394e058..e544deb61d 100644
@@ -58,6 +58,13 @@
 		};
 	};
 
+	fan: pwm-fan {
+		compatible = "pwm-fan";
+		#cooling-cells = <2>;
+		fan-supply = <&vcc12v_dcin>;
+		pwms = <&pwm1 0 50000 0>;
+	};
+
 	sdio_pwrseq: sdio-pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		clocks = <&rk808 1>;
@@ -166,7 +173,7 @@
 		regulator-always-on;
 		regulator-boot-on;
 		regulator-min-microvolt = <800000>;
-		regulator-max-microvolt = <1400000>;
+		regulator-max-microvolt = <1700000>;
 		vin-supply = <&vcc5v0_sys>;
 	};
 };
@@ -222,6 +229,10 @@
 	status = "okay";
 };
 
+&hdmi_sound {
+	status = "okay";
+};
+
 &gpu {
 	mali-supply = <&vdd_gpu>;
 	status = "okay";
@@ -236,8 +247,8 @@
 	rk808: pmic at 1b {
 		compatible = "rockchip,rk808";
 		reg = <0x1b>;
-		interrupt-parent = <&gpio1>;
-		interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
 		#clock-cells = <1>;
 		clock-output-names = "xin32k", "rk808-clkout2";
 		pinctrl-names = "default";
@@ -504,11 +515,25 @@
 	status = "okay";
 
 	bt656-supply = <&vcc1v8_dvp>;
-	audio-supply = <&vcca1v8_codec>;
+	audio-supply = <&vcc_3v0>;
 	sdmmc-supply = <&vcc_sdio>;
 	gpio1830-supply = <&vcc_3v0>;
 };
 
+&pcie0 {
+	ep-gpios = <&gpio2 RK_PD4 GPIO_ACTIVE_HIGH>;
+	num-lanes = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie_perst>;
+	vpcie12v-supply = <&vcc12v_dcin>;
+	vpcie3v3-supply = <&vcc3v3_pcie>;
+	status = "okay";
+};
+
+&pcie_phy {
+	status = "okay";
+};
+
 &pmu_io_domains {
 	pmu1830-supply = <&vcc_3v0>;
 	status = "okay";
@@ -538,6 +563,10 @@
 	};
 
 	pcie {
+		pcie_perst: pcie-perst {
+			rockchip,pins = <2 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
 		pcie_pwr_en: pcie-pwr-en {
 			rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
@@ -545,7 +574,7 @@
 
 	pmic {
 		pmic_int_l: pmic-int-l {
-			rockchip,pins = <1 RK_PC5 RK_FUNC_GPIO &pcfg_pull_up>;
+			rockchip,pins = <3 RK_PB2 RK_FUNC_GPIO &pcfg_pull_up>;
 		};
 
 		vsel1_gpio: vsel1-gpio {
@@ -580,6 +609,10 @@
 	status = "okay";
 };
 
+&pwm1 {
+	status = "okay";
+};
+
 &pwm2 {
 	status = "okay";
 };
@@ -591,7 +624,6 @@
 
 &sdmmc {
 	bus-width = <4>;
-	cap-mmc-highspeed;
 	cap-sd-highspeed;
 	cd-gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
 	disable-wp;
@@ -603,12 +635,21 @@
 
 &sdhci {
 	bus-width = <8>;
-	mmc-hs400-1_8v;
-	mmc-hs400-enhanced-strobe;
+	mmc-hs200-1_8v;
 	non-removable;
 	status = "okay";
 };
 
+&spi1 {
+	status = "okay";
+
+	flash at 0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <10000000>;
+	};
+};
+
 &tcphy0 {
 	status = "okay";
 };

--
2.17.1

#1 lore raw

PATCH 2/2 arm: dts: rk3399-rockpro64: slightly increase center voltage

The rk3399 VD_CENTER voltage domain is not subject to dynamic voltage scaling. So the regulator reset voltage of 0.9V is used on this board. Let u-boot initialize the center voltage to 0.95V as it is done for the VD_LOGIC domain. This avoids instability and occasional linux kernel Opses on this board.

---
Cc: Kever Yang <[email protected]>
Cc: u-boot at lists.denx.de

---
 arch/arm/dts/rk3399-rockpro64-u-boot.dtsi | 5 +++++
 1 file changed, 5 insertions(+)
arch/arm/dts/rk3399-rockpro64-u-boot.dtsi +5 -0
index a073ea25f5..4648513ea9 100644
@@ -11,6 +11,11 @@
 	};
 };
 
+&vdd_center {
+	regulator-min-microvolt = <950000>;
+	regulator-max-microvolt = <950000>;
+};
+
 &vdd_log {
 	regulator-init-microvolt = <950000>;
 };

--
2.17.1

#4 lore raw

PATCH 1/2 arm: dts: rk3399-rockpro64: sync dts from linux kernel

In reply to Soeren Moch
Quoted 3 lines · Soeren Moch

The most important change for u-boot is the fix for the vdd-log pwm voltage regulator to avoid overvoltage for the VD_LOGIC power domain.

I don't see any changes to vdd-log regulator in this patch that can help avoiding overvoltage. It just bumps regulator-max-microvolt to 1700000.

Quoted 154 lines

---
Cc: Kever Yang <[email protected]>
Cc: u-boot at lists.denx.de

---
 arch/arm/dts/rk3399-rockpro64.dts | 57 ++++++++++++++++++++++++++-----
 1 file changed, 49 insertions(+), 8 deletions(-)
arch/arm/dts/rk3399-rockpro64.dts +49 -9
index 1f2394e058..e544deb61d 100644
@@ -58,6 +58,13 @@
                };
        };
 
+       fan: pwm-fan {
+               compatible = "pwm-fan";
+               #cooling-cells = <2>;
+               fan-supply = <&vcc12v_dcin>;
+               pwms = <&pwm1 0 50000 0>;
+       };
+
        sdio_pwrseq: sdio-pwrseq {
                compatible = "mmc-pwrseq-simple";
                clocks = <&rk808 1>;
@@ -166,7 +173,7 @@
                regulator-always-on;
                regulator-boot-on;
                regulator-min-microvolt = <800000>;
-               regulator-max-microvolt = <1400000>;
+               regulator-max-microvolt = <1700000>;
                vin-supply = <&vcc5v0_sys>;
        };
 };
@@ -222,6 +229,10 @@
        status = "okay";
 };
 
+&hdmi_sound {
+       status = "okay";
+};
+
 &gpu {
        mali-supply = <&vdd_gpu>;
        status = "okay";
@@ -236,8 +247,8 @@
        rk808: pmic at 1b {
                compatible = "rockchip,rk808";
                reg = <0x1b>;
-               interrupt-parent = <&gpio1>;
-               interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
+               interrupt-parent = <&gpio3>;
+               interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
                #clock-cells = <1>;
                clock-output-names = "xin32k", "rk808-clkout2";
                pinctrl-names = "default";
@@ -504,11 +515,25 @@
        status = "okay";
 
        bt656-supply = <&vcc1v8_dvp>;
-       audio-supply = <&vcca1v8_codec>;
+       audio-supply = <&vcc_3v0>;
        sdmmc-supply = <&vcc_sdio>;
        gpio1830-supply = <&vcc_3v0>;
 };
 
+&pcie0 {
+       ep-gpios = <&gpio2 RK_PD4 GPIO_ACTIVE_HIGH>;
+       num-lanes = <4>;
+       pinctrl-names = "default";
+       pinctrl-0 = <&pcie_perst>;
+       vpcie12v-supply = <&vcc12v_dcin>;
+       vpcie3v3-supply = <&vcc3v3_pcie>;
+       status = "okay";
+};
+
+&pcie_phy {
+       status = "okay";
+};
+
 &pmu_io_domains {
        pmu1830-supply = <&vcc_3v0>;
        status = "okay";
@@ -538,6 +563,10 @@
        };
 
        pcie {
+               pcie_perst: pcie-perst {
+                       rockchip,pins = <2 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
+               };
+
                pcie_pwr_en: pcie-pwr-en {
                        rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
                };
@@ -545,7 +574,7 @@
 
        pmic {
                pmic_int_l: pmic-int-l {
-                       rockchip,pins = <1 RK_PC5 RK_FUNC_GPIO &pcfg_pull_up>;
+                       rockchip,pins = <3 RK_PB2 RK_FUNC_GPIO &pcfg_pull_up>;
                };
 
                vsel1_gpio: vsel1-gpio {
@@ -580,6 +609,10 @@
        status = "okay";
 };
 
+&pwm1 {
+       status = "okay";
+};
+
 &pwm2 {
        status = "okay";
 };
@@ -591,7 +624,6 @@
 
 &sdmmc {
        bus-width = <4>;
-       cap-mmc-highspeed;
        cap-sd-highspeed;
        cd-gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
        disable-wp;
@@ -603,12 +635,21 @@
 
 &sdhci {
        bus-width = <8>;
-       mmc-hs400-1_8v;
-       mmc-hs400-enhanced-strobe;
+       mmc-hs200-1_8v;
        non-removable;
        status = "okay";
 };
 
+&spi1 {
+       status = "okay";
+
+       flash at 0 {
+               compatible = "jedec,spi-nor";
+               reg = <0>;
+               spi-max-frequency = <10000000>;
+       };
+};
+
 &tcphy0 {
        status = "okay";
 };
--

2.17.1

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot

#5 lore raw

PATCH 1/2 arm: dts: rk3399-rockpro64: sync dts from linux kernel

Quoted 6 lines · Vasily Khoruzhick
Quoted 2 lines · Soeren Moch

The most important change for u-boot is the fix for the vdd-log pwm voltage regulator to avoid overvoltage for the VD_LOGIC power domain.

I don't see any changes to vdd-log regulator in this patch that can help avoiding overvoltage. It just bumps regulator-max-microvolt to 1700000.

The duty-cycle of this pwm regulator is calculated from the min and max values. And with a max value that is set too low for the actual circuitry, a wrong duty-cycle is calculated that results in a higher voltage that what is set in regulator-init-microvolt.
I measured the voltage on the board, with the original setting it was far above the allowed 1.0V, this patch fixes this, also see [1].

Regards,
Soeren

[1] https://patchwork.kernel.org/patch/11173465/

Quoted 155 lines
Quoted 155 lines

---
Cc: Kever Yang <[email protected]>
Cc: u-boot at lists.denx.de

---
 arch/arm/dts/rk3399-rockpro64.dts | 57 ++++++++++++++++++++++++++-----
 1 file changed, 49 insertions(+), 8 deletions(-)
arch/arm/dts/rk3399-rockpro64.dts +49 -9
index 1f2394e058..e544deb61d 100644
@@ -58,6 +58,13 @@
                };
        };
 
+       fan: pwm-fan {
+               compatible = "pwm-fan";
+               #cooling-cells = <2>;
+               fan-supply = <&vcc12v_dcin>;
+               pwms = <&pwm1 0 50000 0>;
+       };
+
        sdio_pwrseq: sdio-pwrseq {
                compatible = "mmc-pwrseq-simple";
                clocks = <&rk808 1>;
@@ -166,7 +173,7 @@
                regulator-always-on;
                regulator-boot-on;
                regulator-min-microvolt = <800000>;
-               regulator-max-microvolt = <1400000>;
+               regulator-max-microvolt = <1700000>;
                vin-supply = <&vcc5v0_sys>;
        };
 };
@@ -222,6 +229,10 @@
        status = "okay";
 };
 
+&hdmi_sound {
+       status = "okay";
+};
+
 &gpu {
        mali-supply = <&vdd_gpu>;
        status = "okay";
@@ -236,8 +247,8 @@
        rk808: pmic at 1b {
                compatible = "rockchip,rk808";
                reg = <0x1b>;
-               interrupt-parent = <&gpio1>;
-               interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
+               interrupt-parent = <&gpio3>;
+               interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
                #clock-cells = <1>;
                clock-output-names = "xin32k", "rk808-clkout2";
                pinctrl-names = "default";
@@ -504,11 +515,25 @@
        status = "okay";
 
        bt656-supply = <&vcc1v8_dvp>;
-       audio-supply = <&vcca1v8_codec>;
+       audio-supply = <&vcc_3v0>;
        sdmmc-supply = <&vcc_sdio>;
        gpio1830-supply = <&vcc_3v0>;
 };
 
+&pcie0 {
+       ep-gpios = <&gpio2 RK_PD4 GPIO_ACTIVE_HIGH>;
+       num-lanes = <4>;
+       pinctrl-names = "default";
+       pinctrl-0 = <&pcie_perst>;
+       vpcie12v-supply = <&vcc12v_dcin>;
+       vpcie3v3-supply = <&vcc3v3_pcie>;
+       status = "okay";
+};
+
+&pcie_phy {
+       status = "okay";
+};
+
 &pmu_io_domains {
        pmu1830-supply = <&vcc_3v0>;
        status = "okay";
@@ -538,6 +563,10 @@
        };
 
        pcie {
+               pcie_perst: pcie-perst {
+                       rockchip,pins = <2 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
+               };
+
                pcie_pwr_en: pcie-pwr-en {
                        rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
                };
@@ -545,7 +574,7 @@
 
        pmic {
                pmic_int_l: pmic-int-l {
-                       rockchip,pins = <1 RK_PC5 RK_FUNC_GPIO &pcfg_pull_up>;
+                       rockchip,pins = <3 RK_PB2 RK_FUNC_GPIO &pcfg_pull_up>;
                };
 
                vsel1_gpio: vsel1-gpio {
@@ -580,6 +609,10 @@
        status = "okay";
 };
 
+&pwm1 {
+       status = "okay";
+};
+
 &pwm2 {
        status = "okay";
 };
@@ -591,7 +624,6 @@
 
 &sdmmc {
        bus-width = <4>;
-       cap-mmc-highspeed;
        cap-sd-highspeed;
        cd-gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
        disable-wp;
@@ -603,12 +635,21 @@
 
 &sdhci {
        bus-width = <8>;
-       mmc-hs400-1_8v;
-       mmc-hs400-enhanced-strobe;
+       mmc-hs200-1_8v;
        non-removable;
        status = "okay";
 };
 
+&spi1 {
+       status = "okay";
+
+       flash at 0 {
+               compatible = "jedec,spi-nor";
+               reg = <0>;
+               spi-max-frequency = <10000000>;
+       };
+};
+
 &tcphy0 {
        status = "okay";
 };
--

2.17.1

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot

#6 lore raw

PATCH 1/2 arm: dts: rk3399-rockpro64: sync dts from linux kernel

Quoted 8 lines · Soeren Moch
Quoted 6 lines · Vasily Khoruzhick
Quoted 2 lines · Soeren Moch

The most important change for u-boot is the fix for the vdd-log pwm voltage regulator to avoid overvoltage for the VD_LOGIC power domain.

I don't see any changes to vdd-log regulator in this patch that can help avoiding overvoltage. It just bumps regulator-max-microvolt to 1700000.

Quoted 6 lines

The duty-cycle of this pwm regulator is calculated from the min and max values. And with a max value that is set too low for the actual circuitry, a wrong duty-cycle is calculated that results in a higher voltage that what is set in regulator-init-microvolt.
I measured the voltage on the board, with the original setting it was far above the allowed 1.0V, this patch fixes this, also see [1].

Thanks for explanation!

Quoted 161 lines

Regards,
Soeren

[1] https://patchwork.kernel.org/patch/11173465/

Quoted 155 lines
Quoted 155 lines

---
Cc: Kever Yang <[email protected]>
Cc: u-boot at lists.denx.de

---
 arch/arm/dts/rk3399-rockpro64.dts | 57 ++++++++++++++++++++++++++-----
 1 file changed, 49 insertions(+), 8 deletions(-)
arch/arm/dts/rk3399-rockpro64.dts +49 -9
index 1f2394e058..e544deb61d 100644
@@ -58,6 +58,13 @@
                };
        };
 
+       fan: pwm-fan {
+               compatible = "pwm-fan";
+               #cooling-cells = <2>;
+               fan-supply = <&vcc12v_dcin>;
+               pwms = <&pwm1 0 50000 0>;
+       };
+
        sdio_pwrseq: sdio-pwrseq {
                compatible = "mmc-pwrseq-simple";
                clocks = <&rk808 1>;
@@ -166,7 +173,7 @@
                regulator-always-on;
                regulator-boot-on;
                regulator-min-microvolt = <800000>;
-               regulator-max-microvolt = <1400000>;
+               regulator-max-microvolt = <1700000>;
                vin-supply = <&vcc5v0_sys>;
        };
 };
@@ -222,6 +229,10 @@
        status = "okay";
 };
 
+&hdmi_sound {
+       status = "okay";
+};
+
 &gpu {
        mali-supply = <&vdd_gpu>;
        status = "okay";
@@ -236,8 +247,8 @@
        rk808: pmic at 1b {
                compatible = "rockchip,rk808";
                reg = <0x1b>;
-               interrupt-parent = <&gpio1>;
-               interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
+               interrupt-parent = <&gpio3>;
+               interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
                #clock-cells = <1>;
                clock-output-names = "xin32k", "rk808-clkout2";
                pinctrl-names = "default";
@@ -504,11 +515,25 @@
        status = "okay";
 
        bt656-supply = <&vcc1v8_dvp>;
-       audio-supply = <&vcca1v8_codec>;
+       audio-supply = <&vcc_3v0>;
        sdmmc-supply = <&vcc_sdio>;
        gpio1830-supply = <&vcc_3v0>;
 };
 
+&pcie0 {
+       ep-gpios = <&gpio2 RK_PD4 GPIO_ACTIVE_HIGH>;
+       num-lanes = <4>;
+       pinctrl-names = "default";
+       pinctrl-0 = <&pcie_perst>;
+       vpcie12v-supply = <&vcc12v_dcin>;
+       vpcie3v3-supply = <&vcc3v3_pcie>;
+       status = "okay";
+};
+
+&pcie_phy {
+       status = "okay";
+};
+
 &pmu_io_domains {
        pmu1830-supply = <&vcc_3v0>;
        status = "okay";
@@ -538,6 +563,10 @@
        };
 
        pcie {
+               pcie_perst: pcie-perst {
+                       rockchip,pins = <2 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
+               };
+
                pcie_pwr_en: pcie-pwr-en {
                        rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
                };
@@ -545,7 +574,7 @@
 
        pmic {
                pmic_int_l: pmic-int-l {
-                       rockchip,pins = <1 RK_PC5 RK_FUNC_GPIO &pcfg_pull_up>;
+                       rockchip,pins = <3 RK_PB2 RK_FUNC_GPIO &pcfg_pull_up>;
                };
 
                vsel1_gpio: vsel1-gpio {
@@ -580,6 +609,10 @@
        status = "okay";
 };
 
+&pwm1 {
+       status = "okay";
+};
+
 &pwm2 {
        status = "okay";
 };
@@ -591,7 +624,6 @@
 
 &sdmmc {
        bus-width = <4>;
-       cap-mmc-highspeed;
        cap-sd-highspeed;
        cd-gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
        disable-wp;
@@ -603,12 +635,21 @@
 
 &sdhci {
        bus-width = <8>;
-       mmc-hs400-1_8v;
-       mmc-hs400-enhanced-strobe;
+       mmc-hs200-1_8v;
        non-removable;
        status = "okay";
 };
 
+&spi1 {
+       status = "okay";
+
+       flash at 0 {
+               compatible = "jedec,spi-nor";
+               reg = <0>;
+               spi-max-frequency = <10000000>;
+       };
+};
+
 &tcphy0 {
        status = "okay";
 };
--

2.17.1

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot

#7 lore raw

PATCH 1/2 arm: dts: rk3399-rockpro64: sync dts from linux kernel

In reply to Soeren Moch
Quoted 8 lines · Soeren Moch

The most important change for u-boot is the fix for the vdd-log pwm voltage regulator to avoid overvoltage for the VD_LOGIC power domain.

=2D--
Cc: Kever Yang <[email protected]>
Cc: u-boot at lists.denx.de
=2D--

Why  is the "=2D- -" here?

Otherwise looks good to me.

Thanks,
- Kever

Quoted 147 lines
  arch/arm/dts/rk3399-rockpro64.dts | 57 ++++++++++++++++++++++++++-----
  1 file changed, 49 insertions(+), 8 deletions(-)
arch/arm/dts/rk3399-rockp= renamed from arch/arm/dts/rk3399-rockpro64.dts +0 -0

ro64.dts
index 1f2394e058..e544deb61d 100644
=2D-- a/arch/arm/dts/rk3399-rockpro64.dts
+++ b/arch/arm/dts/rk3399-rockpro64.dts

arch/arm/dts/rk3399-rockp= renamed from arch/arm/dts/rk3399-rockpro64.dts +49 -8
@@ -58,6 +58,13 @@
  		};
  	};
 
+	fan: pwm-fan {
+		compatible =3D "pwm-fan";
+		#cooling-cells =3D <2>;
+		fan-supply =3D <&vcc12v_dcin>;
+		pwms =3D <&pwm1 0 50000 0>;
+	};
+
  	sdio_pwrseq: sdio-pwrseq {
  		compatible =3D "mmc-pwrseq-simple";
  		clocks =3D <&rk808 1>;
@@ -166,7 +173,7 @@
  		regulator-always-on;
  		regulator-boot-on;
  		regulator-min-microvolt =3D <800000>;
-		regulator-max-microvolt =3D <1400000>;
+		regulator-max-microvolt =3D <1700000>;
  		vin-supply =3D <&vcc5v0_sys>;
  	};
  };
@@ -222,6 +229,10 @@
  	status =3D "okay";
  };
 
+&hdmi_sound {
+	status =3D "okay";
+};
+
  &gpu {
  	mali-supply =3D <&vdd_gpu>;
  	status =3D "okay";
@@ -236,8 +247,8 @@
  	rk808: pmic at 1b {
  		compatible =3D "rockchip,rk808";
  		reg =3D <0x1b>;
-		interrupt-parent =3D <&gpio1>;
-		interrupts =3D <21 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent =3D <&gpio3>;
+		interrupts =3D <10 IRQ_TYPE_LEVEL_LOW>;
  		#clock-cells =3D <1>;
  		clock-output-names =3D "xin32k", "rk808-clkout2";
  		pinctrl-names =3D "default";
@@ -504,11 +515,25 @@
  	status =3D "okay";
 
  	bt656-supply =3D <&vcc1v8_dvp>;
-	audio-supply =3D <&vcca1v8_codec>;
+	audio-supply =3D <&vcc_3v0>;
  	sdmmc-supply =3D <&vcc_sdio>;
  	gpio1830-supply =3D <&vcc_3v0>;
  };
 
+&pcie0 {
+	ep-gpios =3D <&gpio2 RK_PD4 GPIO_ACTIVE_HIGH>;
+	num-lanes =3D <4>;
+	pinctrl-names =3D "default";
+	pinctrl-0 =3D <&pcie_perst>;
+	vpcie12v-supply =3D <&vcc12v_dcin>;
+	vpcie3v3-supply =3D <&vcc3v3_pcie>;
+	status =3D "okay";
+};
+
+&pcie_phy {
+	status =3D "okay";
+};
+
  &pmu_io_domains {
  	pmu1830-supply =3D <&vcc_3v0>;
  	status =3D "okay";
@@ -538,6 +563,10 @@
  	};
 
  	pcie {
+		pcie_perst: pcie-perst {
+			rockchip,pins =3D <2 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
  		pcie_pwr_en: pcie-pwr-en {
  			rockchip,pins =3D <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
  		};
@@ -545,7 +574,7 @@
 
  	pmic {
  		pmic_int_l: pmic-int-l {
-			rockchip,pins =3D <1 RK_PC5 RK_FUNC_GPIO &pcfg_pull_up>;
+			rockchip,pins =3D <3 RK_PB2 RK_FUNC_GPIO &pcfg_pull_up>;
  		};
 
  		vsel1_gpio: vsel1-gpio {
@@ -580,6 +609,10 @@
  	status =3D "okay";
  };
 
+&pwm1 {
+	status =3D "okay";
+};
+
  &pwm2 {
  	status =3D "okay";
  };
@@ -591,7 +624,6 @@
 
  &sdmmc {
  	bus-width =3D <4>;
-	cap-mmc-highspeed;
  	cap-sd-highspeed;
  	cd-gpios =3D <&gpio0 7 GPIO_ACTIVE_LOW>;
  	disable-wp;
@@ -603,12 +635,21 @@
 
  &sdhci {
  	bus-width =3D <8>;
-	mmc-hs400-1_8v;
-	mmc-hs400-enhanced-strobe;
+	mmc-hs200-1_8v;
  	non-removable;
  	status =3D "okay";
  };
 
+&spi1 {
+	status =3D "okay";
+
+	flash at 0 {
+		compatible =3D "jedec,spi-nor";
+		reg =3D <0>;
+		spi-max-frequency =3D <10000000>;
+	};
+};
+
  &tcphy0 {
  	status =3D "okay";
  };

=2D-
2.17.1

#2 lore raw

PATCH 2/2 arm: dts: rk3399-rockpro64: slightly increase center voltage

In reply to Soeren Moch
Quoted 6 lines · Soeren Moch

The rk3399 VD_CENTER voltage domain is not subject to dynamic voltage scaling. So the regulator reset voltage of 0.9V is used on this board. Let u-boot initialize the center voltage to 0.95V as it is done for the VD_LOGIC domain. This avoids instability and occasional linux kernel Opses on this board.

Quoted 6 lines

=2D--
Cc: Kever Yang <[email protected]>
Cc: u-boot at lists.denx.de
=2D--

  arch/arm/dts/rk3399-rockpro64-u-boot.dtsi | 5 +++++

Thanks,
- Kever

Quoted 23 lines
  1 file changed, 5 insertions(+)
arch/arm/dts/rk33= renamed from arch/arm/dts/rk3399-rockpro64-u-boot.dtsi +0 -0

99-rockpro64-u-boot.dtsi
index a073ea25f5..4648513ea9 100644
=2D-- a/arch/arm/dts/rk3399-rockpro64-u-boot.dtsi
+++ b/arch/arm/dts/rk3399-rockpro64-u-boot.dtsi

arch/arm/dts/rk33= renamed from arch/arm/dts/rk3399-rockpro64-u-boot.dtsi +5 -0
@@ -11,6 +11,11 @@
  	};
  };
 
+&vdd_center {
+	regulator-min-microvolt =3D <950000>;
+	regulator-max-microvolt =3D <950000>;
+};
+
  &vdd_log {
  	regulator-init-microvolt =3D <950000>;
  };

=2D-
2.17.1

#8 lore raw

PATCH 1/2 arm: dts: rk3399-rockpro64: sync dts from linux kernel

In reply to Kever Yang
Quoted 5 lines · Kever Yang
Quoted 3 lines · Soeren Moch

The most important change for u-boot is the fix for the vdd-log pwm voltage regulator to avoid overvoltage for the VD_LOGIC power domain.

Quoted 7 lines
Quoted 5 lines

=2D--
Cc: Kever Yang <[email protected]>
Cc: u-boot at lists.denx.de
=2D--

Why  is the "=2D- -" here?

'git send-email' encodes the patch this way. I use git version 2.17.1 . Apparently this this done to avoid problems with MTAs, I also saw 'From' in a patch description encoded in this special way.
Seems to be no problem for other tools, e.g. u-boot patchwork converts this back to the more traditional readable form.

I'm not sure what I should do about this, seems to be more a feature than a bug.

Quoted 5 lines

Otherwise looks good to me.

Thanks,
Soeren

Quoted 154 lines

Thanks,
- Kever

Quoted 148 lines

  arch/arm/dts/rk3399-rockpro64.dts | 57 ++++++++++++++++++++++++++-----

  1 file changed, 49 insertions(+), 8 deletions(-)
arch/arm/dts/rk3399-rockp= renamed from arch/arm/dts/rk3399-rockpro64.dts +0 -0

ro64.dts
index 1f2394e058..e544deb61d 100644
=2D-- a/arch/arm/dts/rk3399-rockpro64.dts
+++ b/arch/arm/dts/rk3399-rockpro64.dts

arch/arm/dts/rk3399-rockp= renamed from arch/arm/dts/rk3399-rockpro64.dts +49 -8
@@ -58,6 +58,13 @@
           };
       };
 
+    fan: pwm-fan {
+        compatible =3D "pwm-fan";
+        #cooling-cells =3D <2>;
+        fan-supply =3D <&vcc12v_dcin>;
+        pwms =3D <&pwm1 0 50000 0>;
+    };
+
       sdio_pwrseq: sdio-pwrseq {
           compatible =3D "mmc-pwrseq-simple";
           clocks =3D <&rk808 1>;
@@ -166,7 +173,7 @@
           regulator-always-on;
           regulator-boot-on;
           regulator-min-microvolt =3D <800000>;
-        regulator-max-microvolt =3D <1400000>;
+        regulator-max-microvolt =3D <1700000>;
           vin-supply =3D <&vcc5v0_sys>;
       };
   };
@@ -222,6 +229,10 @@
       status =3D "okay";
   };
 
+&hdmi_sound {
+    status =3D "okay";
+};
+
   &gpu {
       mali-supply =3D <&vdd_gpu>;
       status =3D "okay";
@@ -236,8 +247,8 @@
       rk808: pmic at 1b {
           compatible =3D "rockchip,rk808";
           reg =3D <0x1b>;
-        interrupt-parent =3D <&gpio1>;
-        interrupts =3D <21 IRQ_TYPE_LEVEL_LOW>;
+        interrupt-parent =3D <&gpio3>;
+        interrupts =3D <10 IRQ_TYPE_LEVEL_LOW>;
           #clock-cells =3D <1>;
           clock-output-names =3D "xin32k", "rk808-clkout2";
           pinctrl-names =3D "default";
@@ -504,11 +515,25 @@
       status =3D "okay";
 
       bt656-supply =3D <&vcc1v8_dvp>;
-    audio-supply =3D <&vcca1v8_codec>;
+    audio-supply =3D <&vcc_3v0>;
       sdmmc-supply =3D <&vcc_sdio>;
       gpio1830-supply =3D <&vcc_3v0>;
   };
 
+&pcie0 {
+    ep-gpios =3D <&gpio2 RK_PD4 GPIO_ACTIVE_HIGH>;
+    num-lanes =3D <4>;
+    pinctrl-names =3D "default";
+    pinctrl-0 =3D <&pcie_perst>;
+    vpcie12v-supply =3D <&vcc12v_dcin>;
+    vpcie3v3-supply =3D <&vcc3v3_pcie>;
+    status =3D "okay";
+};
+
+&pcie_phy {
+    status =3D "okay";
+};
+
   &pmu_io_domains {
       pmu1830-supply =3D <&vcc_3v0>;
       status =3D "okay";
@@ -538,6 +563,10 @@
       };
 
       pcie {
+        pcie_perst: pcie-perst {
+            rockchip,pins =3D <2 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
+        };
+
           pcie_pwr_en: pcie-pwr-en {
               rockchip,pins =3D <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
           };
@@ -545,7 +574,7 @@
 
       pmic {
           pmic_int_l: pmic-int-l {
-            rockchip,pins =3D <1 RK_PC5 RK_FUNC_GPIO &pcfg_pull_up>;
+            rockchip,pins =3D <3 RK_PB2 RK_FUNC_GPIO &pcfg_pull_up>;
           };
 
           vsel1_gpio: vsel1-gpio {
@@ -580,6 +609,10 @@
       status =3D "okay";
   };
 
+&pwm1 {
+    status =3D "okay";
+};
+
   &pwm2 {
       status =3D "okay";
   };
@@ -591,7 +624,6 @@
 
   &sdmmc {
       bus-width =3D <4>;
-    cap-mmc-highspeed;
       cap-sd-highspeed;
       cd-gpios =3D <&gpio0 7 GPIO_ACTIVE_LOW>;
       disable-wp;
@@ -603,12 +635,21 @@
 
   &sdhci {
       bus-width =3D <8>;
-    mmc-hs400-1_8v;
-    mmc-hs400-enhanced-strobe;
+    mmc-hs200-1_8v;
       non-removable;
       status =3D "okay";
   };
 
+&spi1 {
+    status =3D "okay";
+
+    flash at 0 {
+        compatible =3D "jedec,spi-nor";
+        reg =3D <0>;
+        spi-max-frequency =3D <10000000>;
+    };
+};
+
   &tcphy0 {
       status =3D "okay";
   };

=2D-
2.17.1

#9 lore raw

PATCH 1/2 arm: dts: rk3399-rockpro64: sync dts from linux kernel

Quoted 11 lines · Soeren Moch
Quoted 10 lines · Kever Yang
Quoted 8 lines · Soeren Moch

The most important change for u-boot is the fix for the vdd-log pwm voltage regulator to avoid overvoltage for the VD_LOGIC power domain.

=2D--
Cc: Kever Yang <[email protected]>
Cc: u-boot at lists.denx.de
=2D--

Why  is the "=2D- -" here?

Quoted 8 lines

'git send-email' encodes the patch this way. I use git version 2.17.1 . Apparently this this done to avoid problems with MTAs, I also saw 'From' in a patch description encoded in this special way.
Seems to be no problem for other tools, e.g. u-boot patchwork converts this back to the more traditional readable form.

I'm not sure what I should do about this, seems to be more a feature than a bug.

Apparently 'git send-email' changed the default transfer encoding from unspecified 8bit to quoted-printable.
Do you want me to resend these patches with simpler transfer encoding, e.g. 7bit?

Thanks,
Soeren

Quoted 158 lines
Quoted 4 lines

Otherwise looks good to me.

Thanks,
Soeren

Quoted 152 lines

Thanks,
- Kever

Quoted 148 lines

  arch/arm/dts/rk3399-rockpro64.dts | 57 ++++++++++++++++++++++++++-----

  1 file changed, 49 insertions(+), 8 deletions(-)
arch/arm/dts/rk3399-rockp= renamed from arch/arm/dts/rk3399-rockpro64.dts +0 -0

ro64.dts
index 1f2394e058..e544deb61d 100644
=2D-- a/arch/arm/dts/rk3399-rockpro64.dts
+++ b/arch/arm/dts/rk3399-rockpro64.dts

arch/arm/dts/rk3399-rockp= renamed from arch/arm/dts/rk3399-rockpro64.dts +49 -8
@@ -58,6 +58,13 @@
           };
       };
 
+    fan: pwm-fan {
+        compatible =3D "pwm-fan";
+        #cooling-cells =3D <2>;
+        fan-supply =3D <&vcc12v_dcin>;
+        pwms =3D <&pwm1 0 50000 0>;
+    };
+
       sdio_pwrseq: sdio-pwrseq {
           compatible =3D "mmc-pwrseq-simple";
           clocks =3D <&rk808 1>;
@@ -166,7 +173,7 @@
           regulator-always-on;
           regulator-boot-on;
           regulator-min-microvolt =3D <800000>;
-        regulator-max-microvolt =3D <1400000>;
+        regulator-max-microvolt =3D <1700000>;
           vin-supply =3D <&vcc5v0_sys>;
       };
   };
@@ -222,6 +229,10 @@
       status =3D "okay";
   };
 
+&hdmi_sound {
+    status =3D "okay";
+};
+
   &gpu {
       mali-supply =3D <&vdd_gpu>;
       status =3D "okay";
@@ -236,8 +247,8 @@
       rk808: pmic at 1b {
           compatible =3D "rockchip,rk808";
           reg =3D <0x1b>;
-        interrupt-parent =3D <&gpio1>;
-        interrupts =3D <21 IRQ_TYPE_LEVEL_LOW>;
+        interrupt-parent =3D <&gpio3>;
+        interrupts =3D <10 IRQ_TYPE_LEVEL_LOW>;
           #clock-cells =3D <1>;
           clock-output-names =3D "xin32k", "rk808-clkout2";
           pinctrl-names =3D "default";
@@ -504,11 +515,25 @@
       status =3D "okay";
 
       bt656-supply =3D <&vcc1v8_dvp>;
-    audio-supply =3D <&vcca1v8_codec>;
+    audio-supply =3D <&vcc_3v0>;
       sdmmc-supply =3D <&vcc_sdio>;
       gpio1830-supply =3D <&vcc_3v0>;
   };
 
+&pcie0 {
+    ep-gpios =3D <&gpio2 RK_PD4 GPIO_ACTIVE_HIGH>;
+    num-lanes =3D <4>;
+    pinctrl-names =3D "default";
+    pinctrl-0 =3D <&pcie_perst>;
+    vpcie12v-supply =3D <&vcc12v_dcin>;
+    vpcie3v3-supply =3D <&vcc3v3_pcie>;
+    status =3D "okay";
+};
+
+&pcie_phy {
+    status =3D "okay";
+};
+
   &pmu_io_domains {
       pmu1830-supply =3D <&vcc_3v0>;
       status =3D "okay";
@@ -538,6 +563,10 @@
       };
 
       pcie {
+        pcie_perst: pcie-perst {
+            rockchip,pins =3D <2 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
+        };
+
           pcie_pwr_en: pcie-pwr-en {
               rockchip,pins =3D <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
           };
@@ -545,7 +574,7 @@
 
       pmic {
           pmic_int_l: pmic-int-l {
-            rockchip,pins =3D <1 RK_PC5 RK_FUNC_GPIO &pcfg_pull_up>;
+            rockchip,pins =3D <3 RK_PB2 RK_FUNC_GPIO &pcfg_pull_up>;
           };
 
           vsel1_gpio: vsel1-gpio {
@@ -580,6 +609,10 @@
       status =3D "okay";
   };
 
+&pwm1 {
+    status =3D "okay";
+};
+
   &pwm2 {
       status =3D "okay";
   };
@@ -591,7 +624,6 @@
 
   &sdmmc {
       bus-width =3D <4>;
-    cap-mmc-highspeed;
       cap-sd-highspeed;
       cd-gpios =3D <&gpio0 7 GPIO_ACTIVE_LOW>;
       disable-wp;
@@ -603,12 +635,21 @@
 
   &sdhci {
       bus-width =3D <8>;
-    mmc-hs400-1_8v;
-    mmc-hs400-enhanced-strobe;
+    mmc-hs200-1_8v;
       non-removable;
       status =3D "okay";
   };
 
+&spi1 {
+    status =3D "okay";
+
+    flash at 0 {
+        compatible =3D "jedec,spi-nor";
+        reg =3D <0>;
+        spi-max-frequency =3D <10000000>;
+    };
+};
+
   &tcphy0 {
       status =3D "okay";
   };

=2D-
2.17.1

#3 lore raw

PATCH 2/2 arm: dts: rk3399-rockpro64: slightly increase center voltage【请注意,邮件由[email protected]代发】

In reply to Kever Yang
Quoted 8 lines · Kever Yang
Quoted 6 lines · Soeren Moch

The rk3399 VD_CENTER voltage domain is not subject to dynamic voltage scaling. So the regulator reset voltage of 0.9V is used on this board. Let u-boot initialize the center voltage to 0.95V as it is done for the VD_LOGIC domain. This avoids instability and occasional linux kernel Opses on this board.

Quoted 9 lines
Quoted 6 lines

=2D--
Cc: Kever Yang <[email protected]>
Cc: u-boot at lists.denx.de
=2D-- arch/arm/dts/rk3399-rockpro64-u-boot.dtsi | 5 +++++

Applied to u-boot-rockchip master .

Thanks,
- Kever

Quoted 32 lines

Thanks,
- Kever

Quoted 20 lines
  1 file changed, 5 insertions(+)
arch/arm/dts/rk33= renamed from arch/arm/dts/rk3399-rockpro64-u-boot.dtsi +0 -0

99-rockpro64-u-boot.dtsi
index a073ea25f5..4648513ea9 100644
=2D-- a/arch/arm/dts/rk3399-rockpro64-u-boot.dtsi
+++ b/arch/arm/dts/rk3399-rockpro64-u-boot.dtsi

arch/arm/dts/rk33= renamed from arch/arm/dts/rk3399-rockpro64-u-boot.dtsi +5 -0
@@ -11,6 +11,11 @@
       };
   };
 
+&vdd_center {
+    regulator-min-microvolt =3D <950000>;
+    regulator-max-microvolt =3D <950000>;
+};
+
   &vdd_log {
       regulator-init-microvolt =3D <950000>;
   };
Quoted 4 lines

=2D-
2.17.1

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot

#10 lore raw

PATCH 1/2 arm: dts: rk3399-rockpro64: sync dts from linux kernel【请注意,邮件由[email protected]代发】

In reply to Kever Yang
Quoted 11 lines · Kever Yang
Quoted 8 lines · Soeren Moch

The most important change for u-boot is the fix for the vdd-log pwm voltage regulator to avoid overvoltage for the VD_LOGIC power domain.

=2D--
Cc: Kever Yang <[email protected]>
Cc: u-boot at lists.denx.de
=2D--

Quoted 6 lines

Why  is the "=2D- -" here?

Otherwise looks good to me.

Applied to u-boot-rockchip master.

Thanks,
- Kever

Quoted 158 lines

Thanks,
- Kever

Quoted 144 lines

  arch/arm/dts/rk3399-rockpro64.dts | 57 ++++++++++++++++++++++++++-----

  1 file changed, 49 insertions(+), 8 deletions(-)
arch/arm/dts/rk3399-rockp= renamed from arch/arm/dts/rk3399-rockpro64.dts +0 -0

ro64.dts
index 1f2394e058..e544deb61d 100644
=2D-- a/arch/arm/dts/rk3399-rockpro64.dts
+++ b/arch/arm/dts/rk3399-rockpro64.dts

arch/arm/dts/rk3399-rockp= renamed from arch/arm/dts/rk3399-rockpro64.dts +49 -8
@@ -58,6 +58,13 @@
           };
       };
 
+    fan: pwm-fan {
+        compatible =3D "pwm-fan";
+        #cooling-cells =3D <2>;
+        fan-supply =3D <&vcc12v_dcin>;
+        pwms =3D <&pwm1 0 50000 0>;
+    };
+
       sdio_pwrseq: sdio-pwrseq {
           compatible =3D "mmc-pwrseq-simple";
           clocks =3D <&rk808 1>;
@@ -166,7 +173,7 @@
           regulator-always-on;
           regulator-boot-on;
           regulator-min-microvolt =3D <800000>;
-        regulator-max-microvolt =3D <1400000>;
+        regulator-max-microvolt =3D <1700000>;
           vin-supply =3D <&vcc5v0_sys>;
       };
   };
@@ -222,6 +229,10 @@
       status =3D "okay";
   };
 
+&hdmi_sound {
+    status =3D "okay";
+};
+
   &gpu {
       mali-supply =3D <&vdd_gpu>;
       status =3D "okay";
@@ -236,8 +247,8 @@
       rk808: pmic at 1b {
           compatible =3D "rockchip,rk808";
           reg =3D <0x1b>;
-        interrupt-parent =3D <&gpio1>;
-        interrupts =3D <21 IRQ_TYPE_LEVEL_LOW>;
+        interrupt-parent =3D <&gpio3>;
+        interrupts =3D <10 IRQ_TYPE_LEVEL_LOW>;
           #clock-cells =3D <1>;
           clock-output-names =3D "xin32k", "rk808-clkout2";
           pinctrl-names =3D "default";
@@ -504,11 +515,25 @@
       status =3D "okay";
 
       bt656-supply =3D <&vcc1v8_dvp>;
-    audio-supply =3D <&vcca1v8_codec>;
+    audio-supply =3D <&vcc_3v0>;
       sdmmc-supply =3D <&vcc_sdio>;
       gpio1830-supply =3D <&vcc_3v0>;
   };
 
+&pcie0 {
+    ep-gpios =3D <&gpio2 RK_PD4 GPIO_ACTIVE_HIGH>;
+    num-lanes =3D <4>;
+    pinctrl-names =3D "default";
+    pinctrl-0 =3D <&pcie_perst>;
+    vpcie12v-supply =3D <&vcc12v_dcin>;
+    vpcie3v3-supply =3D <&vcc3v3_pcie>;
+    status =3D "okay";
+};
+
+&pcie_phy {
+    status =3D "okay";
+};
+
   &pmu_io_domains {
       pmu1830-supply =3D <&vcc_3v0>;
       status =3D "okay";
@@ -538,6 +563,10 @@
       };
 
       pcie {
+        pcie_perst: pcie-perst {
+            rockchip,pins =3D <2 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
+        };
+
           pcie_pwr_en: pcie-pwr-en {
               rockchip,pins =3D <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
           };
@@ -545,7 +574,7 @@
 
       pmic {
           pmic_int_l: pmic-int-l {
-            rockchip,pins =3D <1 RK_PC5 RK_FUNC_GPIO &pcfg_pull_up>;
+            rockchip,pins =3D <3 RK_PB2 RK_FUNC_GPIO &pcfg_pull_up>;
           };
 
           vsel1_gpio: vsel1-gpio {
@@ -580,6 +609,10 @@
       status =3D "okay";
   };
 
+&pwm1 {
+    status =3D "okay";
+};
+
   &pwm2 {
       status =3D "okay";
   };
@@ -591,7 +624,6 @@
 
   &sdmmc {
       bus-width =3D <4>;
-    cap-mmc-highspeed;
       cap-sd-highspeed;
       cd-gpios =3D <&gpio0 7 GPIO_ACTIVE_LOW>;
       disable-wp;
@@ -603,12 +635,21 @@
 
   &sdhci {
       bus-width =3D <8>;
-    mmc-hs400-1_8v;
-    mmc-hs400-enhanced-strobe;
+    mmc-hs200-1_8v;
       non-removable;
       status =3D "okay";
   };
 
+&spi1 {
+    status =3D "okay";
+
+    flash at 0 {
+        compatible =3D "jedec,spi-nor";
+        reg =3D <0>;
+        spi-max-frequency =3D <10000000>;
+    };
+};
+
   &tcphy0 {
       status =3D "okay";
   };
Quoted 4 lines

=2D-
2.17.1

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot