Skip to contentSkip to conversation

ASoC: wm8904: configure sysclk/FLL automatically

PATCH In review Michael Walle 2 participants 2 messages Nov 8, 2019 – Nov 11, 2019

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 ASoC: wm8904: configure sysclk/FLL automatically

This adds a new mode WM8904_CLK_AUTO which automatically enables the FLL if a frequency different than the MCLK is set.

These additions make the codec work with the simple-card driver in general and especially in systems where the MCLK doesn't match the required clock.

---
changes since v1:
- replaced second clk_get_rate() with mclk_freq

Please note that the v1 patch might still be pending for moderator approval.

 sound/soc/codecs/wm8904.c | 72 ++++++++++++++++++++++++---------------
 sound/soc/codecs/wm8904.h |  1 +
 2 files changed, 45 insertions(+), 28 deletions(-)
sound/soc/codecs/wm8904.c +44 -28
index bcb3c9d5abf0..2a7d23a5daa8 100644
@@ -1410,34 +1410,6 @@ static int wm8904_hw_params(struct snd_pcm_substream *substream,
 	return 0;
 }
 
-
-static int wm8904_set_sysclk(struct snd_soc_dai *dai, int clk_id,
-			     unsigned int freq, int dir)
-{
-	struct snd_soc_component *component = dai->component;
-	struct wm8904_priv *priv = snd_soc_component_get_drvdata(component);
-
-	switch (clk_id) {
-	case WM8904_CLK_MCLK:
-		priv->sysclk_src = clk_id;
-		priv->mclk_rate = freq;
-		break;
-
-	case WM8904_CLK_FLL:
-		priv->sysclk_src = clk_id;
-		break;
-
-	default:
-		return -EINVAL;
-	}
-
-	dev_dbg(dai->dev, "Clock source is %d at %uHz\n", clk_id, freq);
-
-	wm8904_configure_clocking(component);
-
-	return 0;
-}
-
 static int wm8904_set_fmt(struct snd_soc_dai *dai, unsigned int fmt)
 {
 	struct snd_soc_component *component = dai->component;
@@ -1824,6 +1796,50 @@ static int wm8904_set_fll(struct snd_soc_dai *dai, int fll_id, int source,
 	return 0;
 }
 
+static int wm8904_set_sysclk(struct snd_soc_dai *dai, int clk_id,
+			     unsigned int freq, int dir)
+{
+	struct snd_soc_component *component = dai->component;
+	struct wm8904_priv *priv = snd_soc_component_get_drvdata(component);
+	unsigned long mclk_freq;
+	int ret;
+
+	switch (clk_id) {
+	case WM8904_CLK_AUTO:
+		mclk_freq = clk_get_rate(priv->mclk);
+		/* enable FLL if a different sysclk is desired */
+		if (mclk_freq != freq) {
+			priv->sysclk_src = WM8904_CLK_FLL;
+			ret = wm8904_set_fll(dai, WM8904_FLL_MCLK,
+					     WM8904_FLL_MCLK,
+					     mclk_freq, freq);
+			if (ret)
+				return ret;
+			break;
+		}
+		clk_id = WM8904_CLK_MCLK;
+		/* fallthrough */
+
+	case WM8904_CLK_MCLK:
+		priv->sysclk_src = clk_id;
+		priv->mclk_rate = freq;
+		break;
+
+	case WM8904_CLK_FLL:
+		priv->sysclk_src = clk_id;
+		break;
+
+	default:
+		return -EINVAL;
+	}
+
+	dev_dbg(dai->dev, "Clock source is %d at %uHz\n", clk_id, freq);
+
+	wm8904_configure_clocking(component);
+
+	return 0;
+}
+
 static int wm8904_digital_mute(struct snd_soc_dai *codec_dai, int mute)
 {
 	struct snd_soc_component *component = codec_dai->component;
sound/soc/codecs/wm8904.h +1 -0
index c1bca52f9927..de6340446b1f 100644
@@ -10,6 +10,7 @@
 #ifndef _WM8904_H
 #define _WM8904_H
 
+#define WM8904_CLK_AUTO 0
 #define WM8904_CLK_MCLK 1
 #define WM8904_CLK_FLL  2
 
Signature · 1 line
2.20.1
Acked-by on v2 1/1
#1 lore raw
Quoted 9 lines · Michael Walle

This adds a new mode WM8904_CLK_AUTO which automatically enables the FLL if a frequency different than the MCLK is set.

These additions make the codec work with the simple-card driver in general and especially in systems where the MCLK doesn't match the required clock.

---

Thanks,
Charles
_______________________________________________
Alsa-devel mailing list
[email protected]
https://mailman.alsa-project.org/mailman/listinfo/alsa-devel