omap34xx: SPL: enable MMC raw boot with u-boot.img
Subsystems (3)
PATCH 1/1 omap34xx: SPL: enable MMC raw boot with u-boot.img
The following commit enabled raw SPL booting:
22d90d560a omap3: Use raw SPL by default for mmc1
but it was reverted by the following commit:
821c89d38c Revert "omap3: Use raw SPL by default for mmc1"
because SPL is unable to distinguish between RAW images and garbage.
However if CONFIG_SPL_RAW_IMAGE_SUPPORT is disabled, SPL does identify if there is a valid image with spl_parse_image_header.
With this change, and CONFIG_SPL_RAW_IMAGE_SUPPORT disabled, raw MMC boot will be tried first, and if it fails, it FS will be tried.
The two scenarios have been tested on a BeagleBoard XM Revision C1.
--- arch/arm/mach-omap2/boot-common.c | 2 ++ 1 file changed, 2 insertions(+)
arch/arm/mach-omap2/boot-common.c +2 -0
@@ -132,8 +132,10 @@ void save_omap_boot_params(void) (boot_device <= MMC_BOOT_DEVICES_END)) {switch (boot_device) {case BOOT_DEVICE_MMC1 : +#ifdef CONFIG_SPL_RAW_IMAGE_SUPPORT boot_mode =MMCSD_MODE_FS ;break ; +#endif case BOOT_DEVICE_MMC2 : boot_mode =MMCSD_MODE_RAW ;break ;
Signature · 1 line
2.24.0
PATCH 1/1 omap34xx: SPL: enable MMC raw boot with u-boot.img
Quoted 26 lines · On Sun, 10 Nov 2019 01:48:17 +0100 Denis 'GNUtoo' Carikli…
The following commit enabled raw SPL booting:
22d90d560aomap3: Use raw SPL by default for mmc1
but it was reverted by the following commit:
821c89d38cRevert "omap3: Use raw SPL by default for mmc1"
because SPL is unable to distinguish between RAW images and garbage.However if
CONFIG_SPL_RAW_IMAGE_SUPPORTis disabled, SPL does identify if there is a valid image withspl_parse_image_header.With this change, and
CONFIG_SPL_RAW_IMAGE_SUPPORTdisabled, raw MMC boot will be tried first, and if it fails, it FS will be tried.The two scenarios have been tested on a BeagleBoard XM Revision C1.
Signed-off-by Denis 'GNUtoo' Carikli <[email protected]>--- arch/arm/mach-omap2/boot-common.c | 2 ++ 1 file changed, 2 insertions(+)(quoted diff) +0
-0
b/arch/arm/mach-omap2/boot-common.cindex734fa9d9e6..a48244e1c5100644 ---a/arch/arm/mach-omap2/boot-common.c
+++b/arch/arm/mach-omap2/boot-common.c
arch/arm/mach-omap2/boot-common.c void save_omap_boot_params(void) · line 141
Quoted 10 lines
arch/arm/mach-omap2/boot-common.c +2
-0@@ -132,8 +132,10 @@ void save_omap_boot_params(void) (boot_device <= MMC_BOOT_DEVICES_END)) {switch (boot_device) {case BOOT_DEVICE_MMC1 : +#ifdef CONFIG_SPL_RAW_IMAGE_SUPPORT boot_mode =MMCSD_MODE_FS ;break ; +#endif case BOOT_DEVICE_MMC2 : boot_mode =MMCSD_MODE_RAW ;break ;
Ping.
Denis.
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 833 bytes
Desc: OpenPGP digital signature
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200107/85c77086/attachment.sig>
PATCH 1/1 omap34xx: SPL: enable MMC raw boot with u-boot.img
In reply to Denis 'GNUtoo' CarikliQuoted 7 lines · Denis 'GNUtoo' Carikli
The following commit enabled raw SPL booting:
22d90d560aomap3: Use raw SPL by default for mmc1
but it was reverted by the following commit:
821c89d38cRevert "omap3: Use raw SPL by default for mmc1"
because SPL is unable to distinguish between RAW images and garbage.
Quoted 6 lines
However if
CONFIG_SPL_RAW_IMAGE_SUPPORTis disabled, SPL does identify if there is a valid image withspl_parse_image_header.With this change, and
CONFIG_SPL_RAW_IMAGE_SUPPORTdisabled, raw MMC boot will be tried first, and if it fails, it FS will be tried.
This means that if FS boot is required then SPL_RAW_IMAGE_SUPPORT should be disabled. So with this patch applied, the default omap3_defconfig will fail to boot with FS mode. It is difficult to support this unless ROM passes some information on the bootmode.
Thanks and regards,
Lokesh
Quoted 24 lines
The two scenarios have been tested on a BeagleBoard XM Revision C1.
Signed-off-by Denis 'GNUtoo' Carikli <[email protected]>--- arch/arm/mach-omap2/boot-common.c | 2 ++ 1 file changed, 2 insertions(+)arch/arm/mach-omap2/boot-common.c +2
-0@@ -132,8 +132,10 @@ void save_omap_boot_params(void) (boot_device <= MMC_BOOT_DEVICES_END)) {switch (boot_device) {case BOOT_DEVICE_MMC1 : +#ifdef CONFIG_SPL_RAW_IMAGE_SUPPORT boot_mode =MMCSD_MODE_FS ;break ; +#endif case BOOT_DEVICE_MMC2 : boot_mode =MMCSD_MODE_RAW ;break ;