Skip to contentSkip to conversation

tty: Fix Kconfig indentation

PATCH New Krzysztof Kozlowski 1 participant 1 message Nov 20, 2019

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 tty: Fix Kconfig indentation

Adjust indentation from spaces to tab (+optional two spaces) as in coding style with command like:

	$ sed -e 's/^        /\t/' -i */Kconfig
---
 drivers/tty/Kconfig             | 26 ++++-----
 drivers/tty/hvc/Kconfig         |  4 +-
 drivers/tty/serial/8250/Kconfig |  2 +-
 drivers/tty/serial/Kconfig      | 96 ++++++++++++++++-----------------
 4 files changed, 64 insertions(+), 64 deletions(-)
drivers/tty/Kconfig +13 -13
index c7623f99ac0f..ec53b1d4aef3 100644
@@ -85,13 +85,13 @@ config VT_HW_CONSOLE_BINDING
        bool "Support for binding and unbinding console drivers"
        depends on HW_CONSOLE
        ---help---
-         The virtual terminal is the device that interacts with the physical
-         terminal through console drivers. On these systems, at least one
-         console driver is loaded. In other configurations, additional console
-         drivers may be enabled, such as the framebuffer console. If more than
-         1 console driver is enabled, setting this to 'y' will allow you to
-         select the console driver that will serve as the backend for the
-         virtual terminals.
+	 The virtual terminal is the device that interacts with the physical
+	 terminal through console drivers. On these systems, at least one
+	 console driver is loaded. In other configurations, additional console
+	 drivers may be enabled, such as the framebuffer console. If more than
+	 1 console driver is enabled, setting this to 'y' will allow you to
+	 select the console driver that will serve as the backend for the
+	 virtual terminals.
 
 	 See <file:Documentation/driver-api/console.rst> for more
 	 information. For framebuffer console users, please refer to
@@ -173,15 +173,15 @@ config ROCKETPORT
 	depends on SERIAL_NONSTANDARD && (ISA || EISA || PCI)
 	help
 	  This driver supports Comtrol RocketPort and RocketModem PCI boards.   
-          These boards provide 2, 4, 8, 16, or 32 high-speed serial ports or
-          modems.  For information about the RocketPort/RocketModem  boards
-          and this driver read <file:Documentation/driver-api/serial/rocket.rst>.
+	  These boards provide 2, 4, 8, 16, or 32 high-speed serial ports or
+	  modems.  For information about the RocketPort/RocketModem  boards
+	  and this driver read <file:Documentation/driver-api/serial/rocket.rst>.
 
 	  To compile this driver as a module, choose M here: the
 	  module will be called rocket.
 
 	  If you want to compile this driver into the kernel, say Y here.  If
-          you don't have a Comtrol RocketPort/RocketModem card installed, say N.
+	  you don't have a Comtrol RocketPort/RocketModem card installed, say N.
 
 config CYCLADES
 	tristate "Cyclades async mux support"
@@ -437,8 +437,8 @@ config MIPS_EJTAG_FDC_KGDB
 	depends on MIPS_EJTAG_FDC_TTY && KGDB
 	default y
 	help
-          This enables the use of KGDB over an FDC channel, allowing KGDB to be
-          used remotely or when a serial port isn't available.
+	  This enables the use of KGDB over an FDC channel, allowing KGDB to be
+	  used remotely or when a serial port isn't available.
 
 config MIPS_EJTAG_FDC_KGDB_CHAN
 	int "KGDB FDC channel"
drivers/tty/hvc/Kconfig +2 -2
index 4487a6b9acc8..94734ac511bf 100644
@@ -74,7 +74,7 @@ config HVC_UDBG
        depends on PPC
        select HVC_DRIVER
        help
-         This is meant to be used during HW bring up or debugging when
+	 This is meant to be used during HW bring up or debugging when
 	 no other console mechanism exist but udbg, to get you a quick
 	 console for userspace. Do NOT enable in production kernels. 
 
@@ -83,7 +83,7 @@ config HVC_DCC
        depends on ARM || ARM64
        select HVC_DRIVER
        help
-         This console uses the JTAG DCC on ARM to create a console under the HVC
+	 This console uses the JTAG DCC on ARM to create a console under the HVC
 	 driver. This console is used through a JTAG only on ARM. If you don't have
 	 a JTAG then you probably don't want this option.
 
drivers/tty/serial/8250/Kconfig +1 -1
index 771ac5dc6023..fab3d4f20667 100644
@@ -335,7 +335,7 @@ config SERIAL_8250_BCM2835AUX
 
 	  Features and limitations of the UART are
 	    Registers are similar to 16650 registers,
-              set bits in the control registers that are unsupported
+	      set bits in the control registers that are unsupported
 	      are ignored and read back as 0
 	    7/8 bit operation with 1 start and 1 stop bit
 	    8 symbols deep fifo for rx and tx
drivers/tty/serial/Kconfig +48 -48

122 lines not on this page · raw message

Signature · 1 line
2.17.1