mach-imx: bootaux: elf firmware support
Subsystems (3)
PATCH v3 1/1 mach-imx: bootaux: elf firmware support
From: Igor Opaniuk <[email protected]>
Currently imx-specific bootaux command doesn't support ELF format firmware for Cortex-M4 core.
This patches introduces a PoC implementation of handling elf firmware (load_elf_image_phdr() was copy-pasted from elf.c just for PoC). ELF64 binaries isn't supported yet.
This has the advantage that the user does not need to know to which address the binary has been linked to. However, in order to handle and load the elf sections to the right address, we need to translate the Cortex-M4 core memory addresses to primary/host CPU memory addresses (Cortex A7/A9 cores).
This allows to boot firmwares from any location with just using bootaux, e.g.:
Quoted 1 line
tftp ${loadaddr} hello_world.elf && bootaux ${loadaddr}
Similar translation table can be found in the Linux remoteproc driver [1].
[1] https://elixir.bootlin.com/linux/latest/source/drivers/remoteproc/imx_rproc.c
---
arch/arm/include/asm/mach-imx/sys_proto.h | 7 ++ arch/arm/mach-imx/imx_bootaux.c | 96 +++++++++++++++++++++-- arch/arm/mach-imx/mx7/soc.c | 28 +++++++ 3 files changed, 126 insertions(+), 5 deletions(-)
arch/arm/include/asm/mach-imx/sys_proto.h +7 -0
@@ -106,6 +106,13 @@ void gpr_init(void);#endif /* CONFIG_MX6 */ +/* address translation table */ +struct rproc_att { +u32 da;/* device address (From Cortex M4 view) */ +u32 sa;/* system bus address */ +u32 size;/* size of reg range */ +}; + #ifdef CONFIG_IMX8M struct rom_api { u16 ver;
arch/arm/mach-imx/imx_bootaux.c +91 -5
111 lines not on this page · raw message
arch/arm/mach-imx/mx7/soc.c +28 -0
@@ -193,6 +193,34 @@ static void init_cpu_basic(void)#endif } +#ifdef CONFIG_IMX_BOOTAUX +/* +* Table of mappings of physical mem regions in both +* Cortex-A7 and Cortex-M4 address spaces. +* +* For additional details check sections 2.1.2 and 2.1.3 in +* i.MX7Dual Applications Processor Reference Manual +* +*/ +const struct rproc_att hostmap[] = { +/* aux core , host core, size */ + {0x00000000 ,0x00180000 ,0x8000 },/* OCRAM_S */ + {0x00180000 ,0x00180000 ,0x8000 },/* OCRAM_S */ + {0x20180000 ,0x00180000 ,0x8000 },/* OCRAM_S */ + {0x1fff8000 ,0x007f8000 ,0x8000 },/* TCML */ + {0x20000000 ,0x00800000 ,0x8000 },/* TCMU */ + {0x00900000 ,0x00900000 ,0x20000 },/* OCRAM_128KB */ + {0x20200000 ,0x00900000 ,0x20000 },/* OCRAM_128KB */ + {0x00920000 ,0x00920000 ,0x20000 },/* OCRAM_EPDC */ + {0x20220000 ,0x00920000 ,0x20000 },/* OCRAM_EPDC */ + {0x00940000 ,0x00940000 ,0x20000 },/* OCRAM_PXP */ + {0x20240000 ,0x00940000 ,0x20000 },/* OCRAM_PXP */ + {0x10000000 ,0x80000000 ,0x0fff0000 },/* DDR Code alias */ + {0x80000000 ,0x80000000 ,0xe0000000 },/* DDRC */ + {/* sentinel */ } +}; +#endif +#ifndef CONFIG_SKIP_LOWLEVEL_INIT /* enable all periherial can be accessed in nosec mode */ static void init_csu (void )
Signature · 1 line
2.17.1
PATCH v3 1/1 mach-imx: bootaux: elf firmware support
Quoted 13 lines
From: Igor Opaniuk <[email protected]>
Currently imx-specific bootaux command doesn't support ELF format firmware for Cortex-M4 core.
This patches introduces a PoC implementation of handling elf firmware (load_elf_image_phdr()was copy-pasted fromelf.cjust for PoC). ELF64 binaries isn't supported yet.
This has the advantage that the user does not need to know to which address the binary has been linked to. However, in order to handle and load the elf sections to the right address, we need to translate the Cortex-M4 core memory addresses to primary/host CPU memory addresses (Cortex A7/A9 cores).
This allows to boot firmwares from any location with just using bootaux, e.g.:
Quoted 7 lines
Quoted 1 line
tftp ${loadaddr} hello_world.elf && bootaux ${loadaddr}
Similar translation table can be found in the Linux remoteproc driver [1].
[1] https://elixir.bootlin.com/linux/latest/source/drivers/remoteproc/imx_rproc.cSigned-off-by Igor Opaniuk <[email protected]>Signed-off-by Stefan Agner <[email protected]>Reviewed-by Oleksandr Suvorov <[email protected]>
Applied to u-boot-imx, -next, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================