Skip to contentSkip to conversation

media: sun4i-csi: A10/A20 CSI1 and R40 CSI0 support

PATCH In review Chen-Yu Tsai 2 participants 11 messages Jan 6, 2020 – Mar 12, 2020

Subsystems (2)
lore
Share & tools
lore
author maintainer
#3 lore raw

PATCH v2 3/7 dt-bindings: bus: sunxi: Add R40 MBUS compatible

In reply to Chen-Yu Tsai

From: Chen-Yu Tsai <[email protected]>

Allwinner R40 SoC also contains MBUS controller.

Add compatible for it.

---
Changes since v1:

- Reworked on top of "dt-bindings: interconnect: Convert Allwinner MBUS controller to a schema"

This particular patch should go through Rob's tree, instead of the sunxi tree.

---
 .../devicetree/bindings/arm/sunxi/allwinner,sun4i-a10-mbus.yaml  | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/arm/sunxi/allwinner,sun4i-a10-mbus.yaml +1 -0
index 9370e64992dd..23cda7437dcb 100644
@@ -30,6 +30,7 @@ properties:
     enum:
       - allwinner,sun5i-a13-mbus
       - allwinner,sun8i-h3-mbus
+      - allwinner,sun8i-r40-mbus
 
   reg:
     maxItems: 1
Signature · 1 line
2.24.1
author maintainer
#6 lore raw

PATCH v2 4/7 ARM: dts: sun8i: r40: Add device node for CSI0

In reply to Chen-Yu Tsai

From: Chen-Yu Tsai <[email protected]>

The CSI0 and CSI1 blocks are the same as found on the A20. However only CSI0 is supported upstream right now.

Add a device node for CSI0 using the A20 compatible as a fallback, and the standard pinctrl options. Also add the MBUS interconnect.

---
 arch/arm/boot/dts/sun8i-r40.dtsi | 36 ++++++++++++++++++++++++++++++++
 1 file changed, 36 insertions(+)
arch/arm/boot/dts/sun8i-r40.dtsi +36 -0
index 7c940b20b81c..84d240c39f0f 100644
@@ -181,6 +181,20 @@ nmi_intc: interrupt-controller@1c00030 {
 			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
+		csi0: csi@1c09000 {
+			compatible = "allwinner,sun8i-r40-csi0",
+				     "allwinner,sun7i-a20-csi0";
+			reg = <0x01c09000 0x1000>;
+			interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_CSI0>, <&ccu CLK_CSI_SCLK>,
+				 <&ccu CLK_DRAM_CSI0>;
+			clock-names = "bus", "isp", "ram";
+			resets = <&ccu RST_BUS_CSI0>;
+			interconnects = <&mbus 5>;
+			interconnect-names = "dma-mem";
+			status = "disabled";
+		};
+
 		mmc0: mmc@1c0f000 {
 			compatible = "allwinner,sun8i-r40-mmc",
 				     "allwinner,sun50i-a64-mmc";
@@ -356,6 +370,20 @@ clk_out_a_pin: clk-out-a-pin {
 				function = "clk_out_a";
 			};
 
+			/omit-if-no-ref/
+			csi0_8bits_pins: csi0-8bits-pins {
+				pins = "PE0", "PE2", "PE3", "PE4", "PE5",
+				       "PE6", "PE7", "PE8", "PE9", "PE10",
+				       "PE11";
+				function = "csi0";
+			};
+
+			/omit-if-no-ref/
+			csi0_mclk_pin: csi0-mclk-pin {
+				pins = "PE1";
+				function = "csi0";
+			};
+
 			gmac_rgmii_pins: gmac-rgmii-pins {
 				pins = "PA0", "PA1", "PA2", "PA3",
 				       "PA4", "PA5", "PA6", "PA7",
@@ -625,6 +653,14 @@ gmac_mdio: mdio {
 			};
 		};
 
+		mbus: dram-controller@1c62000 {
+			compatible = "allwinner,sun8i-r40-mbus";
+			reg = <0x01c62000 0x1000>;
+			clocks = <&ccu 155>;
+			dma-ranges = <0x00000000 0x40000000 0x80000000>;
+			#interconnect-cells = <1>;
+		};
+
 		tcon_top: tcon-top@1c70000 {
 			compatible = "allwinner,sun8i-r40-tcon-top";
 			reg = <0x01c70000 0x1000>;
Signature · 1 line
2.24.1
author maintainer
#2 lore raw

PATCH v2 2/7 ARM: dts: sun7i: Add CSI1 controller and pinmux options

In reply to Chen-Yu Tsai

From: Chen-Yu Tsai <[email protected]>

The CSI controller driver now supports the second CSI controller, CSI1.

Add a device node for it. Pinmuxing options for the MCLK output, the standard 8-bit interface, and a secondary 24-bit interface are included.

---
 arch/arm/boot/dts/sun7i-a20.dtsi | 36 ++++++++++++++++++++++++++++++++
 1 file changed, 36 insertions(+)
arch/arm/boot/dts/sun7i-a20.dtsi +36 -0
index 8aebefd6accf..92b5be97085d 100644
@@ -729,6 +729,17 @@ ohci1: usb@1c1c400 {
 			status = "disabled";
 		};
 
+		csi1: csi@1c1d000 {
+			compatible = "allwinner,sun7i-a20-csi1",
+				     "allwinner,sun4i-a10-csi1";
+			reg = <0x01c1d000 0x1000>;
+			interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_AHB_CSI1>, <&ccu CLK_DRAM_CSI1>;
+			clock-names = "bus", "ram";
+			resets = <&ccu RST_CSI1>;
+			status = "disabled";
+		};
+
 		spi3: spi@1c1f000 {
 			compatible = "allwinner,sun4i-a10-spi";
 			reg = <0x01c1f000 0x1000>;
@@ -802,6 +813,31 @@ csi0_clk_pin: csi-clk-pin {
 				function = "csi0";
 			};
 
+			/omit-if-no-ref/
+			csi1_8bits_pg_pins: csi1-8bits-pg-pins {
+				pins = "PG0", "PG2", "PG3", "PG4", "PG5",
+				       "PG6", "PG7", "PG8", "PG9", "PG10",
+				       "PG11";
+				function = "csi1";
+			};
+
+			/omit-if-no-ref/
+			csi1_24bits_ph_pins: csi1-24bits-ph-pins {
+				pins = "PH0", "PH1", "PH2", "PH3", "PH4",
+				       "PH5", "PH6", "PH7", "PH8", "PH9",
+				       "PH10", "PH11", "PH12", "PH13", "PH14",
+				       "PH15", "PH16", "PH17", "PH18", "PH19",
+				       "PH20", "PH21", "PH22", "PH23", "PH24",
+				       "PH25", "PH26", "PH27";
+				function = "csi1";
+			};
+
+			/omit-if-no-ref/
+			csi1_clk_pg_pin: csi1-clk-pg-pin {
+				pins = "PG1";
+				function = "csi1";
+			};
+
 			/omit-if-no-ref/
 			emac_pa_pins: emac-pa-pins {
 				pins = "PA0", "PA1", "PA2",
Signature · 1 line
2.24.1
author maintainer
#7 lore raw

PATCH v2 5/7 ARM: dts: sun4i: cubieboard: Enable OV7670 camera on CSI1

In reply to Chen-Yu Tsai

From: Chen-Yu Tsai <[email protected]>

The Cubieboard has CSI1 pins exposed on one of its GPIO headers. Combined with I2C1 on the same header, a connected OV7670 based camera module can be used. Power is provided via the 5V rail on the same header. The module has onboard LDOs for the sensor's various power rails.

Add a device node for the sensor, enable CSI1 and I2C1, and hook everything up.

---
 arch/arm/boot/dts/sun4i-a10-cubieboard.dts | 42 ++++++++++++++++++++++
 1 file changed, 42 insertions(+)
arch/arm/boot/dts/sun4i-a10-cubieboard.dts +42 -0
index 6ca02e824acc..29bfec8fad5b 100644
@@ -101,6 +101,25 @@ &cpu0 {
 	cpu-supply = <&reg_dcdc2>;
 };
 
+&csi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&csi1_8bits_pg_pins>;
+	status = "okay";
+
+	port {
+		/* Parallel bus endpoint */
+		csi_from_ov7670: endpoint {
+			remote-endpoint = <&ov7670_to_csi>;
+			bus-width = <8>;
+			/* driver is broken */
+			hsync-active = <0>; /* Active high */
+			vsync-active = <1>; /* Active high */
+			data-active = <1>;  /* Active high */
+			pclk-sample = <1>;  /* Rising */
+		};
+	};
+};
+
 &de {
 	status = "okay";
 };
@@ -143,6 +162,29 @@ axp209: pmic@34 {
 
 &i2c1 {
 	status = "okay";
+
+	ov7670: camera@21 {
+		compatible = "ovti,ov7670";
+		reg = <0x21>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&csi1_clk_pg_pin>;
+		clocks = <&ccu CLK_CSI1>;
+		clock-names = "xclk";
+
+		reset-gpios = <&pio 7 14 GPIO_ACTIVE_LOW>; /* PH14 */
+		powerdown-gpios = <&pio 7 15 GPIO_ACTIVE_HIGH>; /* PH15 */
+
+		port {
+			ov7670_to_csi: endpoint {
+				remote-endpoint = <&csi_from_ov7670>;
+				bus-width = <8>;
+				hsync-active = <1>; /* Active high */
+				vsync-active = <1>; /* Active high */
+				data-active = <1>;  /* Active high */
+				pclk-sample = <1>;  /* Rising */
+			};
+		};
+	};
 };
 
 &ir0 {
Signature · 1 line
2.24.1
author maintainer
#1 lore raw

PATCH v2 1/7 ARM: dts: sun4i: Add CSI1 controller and pinmux options

In reply to Chen-Yu Tsai

From: Chen-Yu Tsai <[email protected]>

The CSI controller driver now supports the second CSI controller, CSI1.

Add a device node for it. Pinmuxing options for the MCLK output, the standard 8-bit interface, and a secondary 24-bit interface are included.

---
 arch/arm/boot/dts/sun4i-a10.dtsi | 35 ++++++++++++++++++++++++++++++++
 1 file changed, 35 insertions(+)
arch/arm/boot/dts/sun4i-a10.dtsi +35 -0
index 4c268b70b735..bf531efc0610 100644
@@ -624,6 +624,16 @@ ohci1: usb@1c1c400 {
 			status = "disabled";
 		};
 
+		csi1: csi@1c1d000 {
+			compatible = "allwinner,sun4i-a10-csi1";
+			reg = <0x01c1d000 0x1000>;
+			interrupts = <43>;
+			clocks = <&ccu CLK_AHB_CSI1>, <&ccu CLK_DRAM_CSI1>;
+			clock-names = "bus", "ram";
+			resets = <&ccu RST_CSI1>;
+			status = "disabled";
+		};
+
 		spi3: spi@1c1f000 {
 			compatible = "allwinner,sun4i-a10-spi";
 			reg = <0x01c1f000 0x1000>;
@@ -670,6 +680,31 @@ can0_ph_pins: can0-ph-pins {
 				function = "can";
 			};
 
+			/omit-if-no-ref/
+			csi1_8bits_pg_pins: csi1-8bits-pg-pins {
+				pins = "PG0", "PG2", "PG3", "PG4", "PG5",
+				       "PG6", "PG7", "PG8", "PG9", "PG10",
+				       "PG11";
+				function = "csi1";
+			};
+
+			/omit-if-no-ref/
+			csi1_24bits_ph_pins: csi1-24bits-ph-pins {
+				pins = "PH0", "PH1", "PH2", "PH3", "PH4",
+				       "PH5", "PH6", "PH7", "PH8", "PH9",
+				       "PH10", "PH11", "PH12", "PH13", "PH14",
+				       "PH15", "PH16", "PH17", "PH18", "PH19",
+				       "PH20", "PH21", "PH22", "PH23", "PH24",
+				       "PH25", "PH26", "PH27";
+				function = "csi1";
+			};
+
+			/omit-if-no-ref/
+			csi1_clk_pg_pin: csi1-clk-pg-pin {
+				pins = "PG1";
+				function = "csi1";
+			};
+
 			emac_pins: emac0-pins {
 				pins = "PA0", "PA1", "PA2",
 				       "PA3", "PA4", "PA5", "PA6",
Signature · 7 lines
2.24.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
author maintainer
#9 lore raw

PATCH v2 7/7 ARM: dts: sun8i-r40: bananapi-m2-ultra: Enable OV5640 camera

In reply to Chen-Yu Tsai

From: Chen-Yu Tsai <[email protected]>

Bananapi offers a small OV5640 based camera module, attached via an FPC connector.

Add the related regulator constraints, and hook everything up.

---
 .../boot/dts/sun8i-r40-bananapi-m2-ultra.dts  | 67 +++++++++++++++++++
 1 file changed, 67 insertions(+)
arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts +67 -0
index 42d62d1ba1dc..86183d40c7af 100644
@@ -113,6 +113,24 @@ &ahci {
 	status = "okay";
 };
 
+&csi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&csi0_8bits_pins>;
+	status = "okay";
+
+	port {
+		/* Parallel bus endpoint */
+		csi0_from_ov5640: endpoint {
+			remote-endpoint = <&ov5640_to_csi0>;
+			bus-width = <8>;
+			hsync-active = <1>; /* Active high */
+			vsync-active = <1>; /* Active high */
+			data-active = <1>;  /* Active high */
+			pclk-sample = <1>;  /* Rising */
+		};
+	};
+};
+
 &de {
 	status = "okay";
 };
@@ -164,6 +182,37 @@ axp22x: pmic@34 {
 
 #include "axp22x.dtsi"
 
+&i2c4 {
+	status = "okay";
+
+	ov5640: camera@3c {
+		compatible = "ovti,ov5640";
+		reg = <0x3c>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&csi0_mclk_pin>;
+		clocks = <&ccu CLK_CSI0_MCLK>;
+		clock-names = "xclk";
+
+		reset-gpios = <&pio 8 7 GPIO_ACTIVE_LOW>; /* PI7 */
+		powerdown-gpios = <&pio 8 6 GPIO_ACTIVE_HIGH>; /* PI6 */
+		AVDD-supply = <&reg_aldo1>;
+		DOVDD-supply = <&reg_eldo1>;
+		DVDD-supply = <&reg_eldo2>;
+
+		port {
+			ov5640_to_csi0: endpoint {
+				remote-endpoint = <&csi0_from_ov5640>;
+				bus-width = <8>;
+				data-shift = <2>;
+				hsync-active = <1>; /* Active high */
+				vsync-active = <1>; /* Active high */
+				data-active = <1>;  /* Active high */
+				pclk-sample = <1>;  /* Rising */
+			};
+		};
+	};
+};
+
 &mmc0 {
 	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <4>;
@@ -209,6 +258,12 @@ &pio {
 	vcc-pg-supply = <&reg_dldo1>;
 };
 
+&reg_aldo1 {
+	regulator-name = "csi-avdd";
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+};
+
 &reg_aldo2 {
 	regulator-min-microvolt = <2500000>;
 	regulator-max-microvolt = <2500000>;
@@ -289,6 +344,18 @@ &reg_dldo4 {
 	regulator-name = "vdd2v5-sata";
 };
 
+&reg_eldo1 {
+	regulator-name = "csi-iovcc";
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+};
+
+&reg_eldo2 {
+	regulator-name = "csi-dvdd";
+	regulator-min-microvolt = <1500000>;
+	regulator-max-microvolt = <1500000>;
+};
+
 &reg_eldo3 {
 	regulator-min-microvolt = <1200000>;
 	regulator-max-microvolt = <1200000>;
Signature · 1 line
2.24.1
author maintainer
#8 lore raw

PATCH v2 6/7 ARM: dts: sun7i: cubieboard2: Enable OV7670 camera on CSI1

In reply to Chen-Yu Tsai

From: Chen-Yu Tsai <[email protected]>

The Cubieboard2 has CSI1 pins exposed on one of its GPIO headers. Combined with I2C1 on the same header, a connected OV7670 based camera module can be used. Power is provided via the 5V rail on the same header. The module has onboard LDOs for the sensor's various power rails.

Add a device node for the sensor, enable CSI1 and I2C1, and hook everything up.

---
 arch/arm/boot/dts/sun7i-a20-cubieboard2.dts | 42 +++++++++++++++++++++
 1 file changed, 42 insertions(+)
arch/arm/boot/dts/sun7i-a20-cubieboard2.dts +42 -0
index b8203e4ef21c..0ff1593041eb 100644
@@ -100,6 +100,25 @@ &cpu0 {
 	cpu-supply = <&reg_dcdc2>;
 };
 
+&csi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&csi1_8bits_pg_pins>;
+	status = "okay";
+
+	port {
+		/* Parallel bus endpoint */
+		csi_from_ov7670: endpoint {
+			remote-endpoint = <&ov7670_to_csi>;
+			bus-width = <8>;
+			/* driver is broken */
+			hsync-active = <0>; /* Active high */
+			vsync-active = <1>; /* Active high */
+			data-active = <1>;  /* Active high */
+			pclk-sample = <1>;  /* Rising */
+		};
+	};
+};
+
 &de {
 	status = "okay";
 };
@@ -142,6 +161,29 @@ axp209: pmic@34 {
 
 &i2c1 {
 	status = "okay";
+
+	ov7670: camera@21 {
+		compatible = "ovti,ov7670";
+		reg = <0x21>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&csi1_clk_pg_pin>;
+		clocks = <&ccu CLK_CSI1>;
+		clock-names = "xclk";
+
+		reset-gpios = <&pio 7 14 GPIO_ACTIVE_LOW>; /* PH14 */
+		powerdown-gpios = <&pio 7 15 GPIO_ACTIVE_HIGH>; /* PH15 */
+
+		port {
+			ov7670_to_csi: endpoint {
+				remote-endpoint = <&csi_from_ov7670>;
+				bus-width = <8>;
+				hsync-active = <1>; /* Active high */
+				vsync-active = <1>; /* Active high */
+				data-active = <1>;  /* Active high */
+				pclk-sample = <1>;  /* Rising */
+			};
+		};
+	};
 };
 
 &ir0 {
Signature · 1 line
2.24.1

Chen-Yu Tsai

author maintainer
#0 lore raw

v2 cover media: sun4i-csi: A10/A20 CSI1 and R40 CSI0 support

From: Chen-Yu Tsai <[email protected]>

Hi everyone,

This is v2 of my A10/A20 CSI1 and R40 CSI0 series. v2 is simply the remaining patches rebased on top of linux-next 20200106, with the MBUS device tree binding changes converted to YAML format.

This series adds basic support for CSI1 on Allwinner A10/A20 and CSI0 on Allwinner R40. The CSI1 block has the same structure and layout as the CSI0 block. Differences include:

- Only one channel in BT.656 instead of four in CSI0
- 10-bit raw data input vs 8-bit in CSI0
- 24-bit RGB888/YUV444 input vs 16-bit RGB565/YUV422 in CSI0
- No ISP hardware (CSI SCLK not needed)

The CSI0 block in the Allwinner R40 SoC looks to be the same as the one in the A20. The register maps line up, and they support the same features. The R40 appears to support BT.1120 based on the feature overview, but it is not mentioned anywhere else. Also like the A20, the ISP is not mentioned, but the CSI special clock needs to be enabled for the hardware to function. The manual does state that the CSI special clock is the TOP clock for all CSI hardware, but currently no hardware exists for us to test if CSI1 also depends on it or not.

Included are a couple of fixes for signal polarity and DRAM offset handling.

Patches 1 and 2 add CSI1 to A10 (sun4i) and A20 (sun7i) dtsi files.

Patch 3 adds a compatible string for the R40's MBUS (memory bus). This patch needs to go through Rob's tree as it now depends on the patch "dt-bindings: interconnect: Convert Allwinner MBUS controller to a schema" that was already merged.

Patch 4 adds CSI0 to the R40 dtsi file

Patches 5 through 7 are examples of cameras hooked up to boards.

Regards
ChenYu

Chen-Yu Tsai (7):
ARM: dts: sun4i: Add CSI1 controller and pinmux options
ARM: dts: sun7i: Add CSI1 controller and pinmux options
dt-bindings: bus: sunxi: Add R40 MBUS compatible
ARM: dts: sun8i: r40: Add device node for CSI0
[DO NOT MERGE] ARM: dts: sun4i: cubieboard: Enable OV7670 camera on
CSI1
[DO NOT MERGE] ARM: dts: sun7i: cubieboard2: Enable OV7670 camera on
CSI1
[DO NOT MERGE] ARM: dts: sun8i-r40: bananapi-m2-ultra: Enable OV5640
camera

 .../arm/sunxi/allwinner,sun4i-a10-mbus.yaml   |  1 +
 arch/arm/boot/dts/sun4i-a10-cubieboard.dts    | 42 ++++++++++++
 arch/arm/boot/dts/sun4i-a10.dtsi              | 35 ++++++++++
 arch/arm/boot/dts/sun7i-a20-cubieboard2.dts   | 42 ++++++++++++
 arch/arm/boot/dts/sun7i-a20.dtsi              | 36 ++++++++++
 .../boot/dts/sun8i-r40-bananapi-m2-ultra.dts  | 67 +++++++++++++++++++
 arch/arm/boot/dts/sun8i-r40.dtsi              | 36 ++++++++++
 7 files changed, 259 insertions(+)
Signature · 1 line
2.24.1
#10 lore raw
In reply to Chen-Yu Tsai
Quoted 31 lines · Chen-Yu Tsai

From: Chen-Yu Tsai <[email protected]>

Hi everyone,

This is v2 of my A10/A20 CSI1 and R40 CSI0 series. v2 is simply the remaining patches rebased on top of linux-next 20200106, with the MBUS device tree binding changes converted to YAML format.

This series adds basic support for CSI1 on Allwinner A10/A20 and CSI0 on Allwinner R40. The CSI1 block has the same structure and layout as the CSI0 block. Differences include:

- Only one channel in BT.656 instead of four in CSI0
- 10-bit raw data input vs 8-bit in CSI0
- 24-bit RGB888/YUV444 input vs 16-bit RGB565/YUV422 in CSI0
- No ISP hardware (CSI SCLK not needed)

The CSI0 block in the Allwinner R40 SoC looks to be the same as the one in the A20. The register maps line up, and they support the same features. The R40 appears to support BT.1120 based on the feature overview, but it is not mentioned anywhere else. Also like the A20, the ISP is not mentioned, but the CSI special clock needs to be enabled for the hardware to function. The manual does state that the CSI special clock is the TOP clock for all CSI hardware, but currently no hardware exists for us to test if CSI1 also depends on it or not.

Included are a couple of fixes for signal polarity and DRAM offset handling.

Patches 1 and 2 add CSI1 to A10 (sun4i) and A20 (sun7i) dtsi files.

Quoted 8 lines

Patch 3 adds a compatible string for the R40's MBUS (memory bus). This patch needs to go through Rob's tree as it now depends on the patch "dt-bindings: interconnect: Convert Allwinner MBUS controller to a schema" that was already merged.

Patch 4 adds CSI0 to the R40 dtsi file

Patches 5 through 7 are examples of cameras hooked up to boards.

Applied 1,2 and 4, thanks!
Maxime

author maintainer
#5 lore raw

Re: [PATCH v2 3/7] dt-bindings: bus: sunxi: Add R40 MBUS compatible

In reply to Maxime Ripard

Hi Rob,

Quoted 11 lines · Maxime Ripard
Quoted 7 lines · Chen-Yu Tsai

From: Chen-Yu Tsai <[email protected]>

Allwinner R40 SoC also contains MBUS controller.

Add compatible for it.

Looks like this didn't get picked up. But the device tree change using the new compatible did make it into v5.6-rc1.

Could you pick this up as a fix for v5.6 so they make the same release? Or I could pick it through our tree.

Regards
ChenYu