Skip to contentSkip to conversation

ARM: dts: stm32: Add DH Electronics DHCOM SoM and PDK2 board

PATCH Superseded Marek Vasut 2 participants 5 messages Jan 21, 2020 – Jan 24, 2020

Subsystems (4)

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 ARM: dts: stm32: Add DH Electronics DHCOM SoM and PDK2 board

Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier board. This is an SoM with STM32MP157C and an evaluation kit. The baseboard provides Ethernet, UART, USB, CAN and optional display.

Cc Patrick Delaunay <[email protected]>
Cc Patrice Chotard <[email protected]>

---
V2: Rebase on u-boot/master and multi-board changes.

---
 arch/arm/dts/Makefile                         |   1 +
 .../arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts |   7 +
 arch/arm/dts/stm32mp157c-dhcom-pdk2.dts       |  88 ++
 arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi    | 238 ++++++
 arch/arm/dts/stm32mp157c-dhcom.dtsi           | 379 +++++++++
 arch/arm/mach-stm32mp/Kconfig                 |   9 +
 board/dhelectronics/dh_stm32mp1/Kconfig       |  21 +
 board/dhelectronics/dh_stm32mp1/MAINTAINERS   |   7 +
 board/dhelectronics/dh_stm32mp1/Makefile      |  12 +
 board/dhelectronics/dh_stm32mp1/board.c       | 778 ++++++++++++++++++
 configs/stm32mp15_dhcom_basic_defconfig       | 138 ++++
 11 files changed, 1678 insertions(+)
 create mode 100644 arch/arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts
 create mode 100644 arch/arm/dts/stm32mp157c-dhcom-pdk2.dts
 create mode 100644 arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi
 create mode 100644 arch/arm/dts/stm32mp157c-dhcom.dtsi
 create mode 100644 board/dhelectronics/dh_stm32mp1/Kconfig
 create mode 100644 board/dhelectronics/dh_stm32mp1/MAINTAINERS
 create mode 100644 board/dhelectronics/dh_stm32mp1/Makefile
 create mode 100644 board/dhelectronics/dh_stm32mp1/board.c
 create mode 100644 configs/stm32mp15_dhcom_basic_defconfig
arch/arm/dts/Makefile +1 -0
index e469d191fb..cf0c75e006 100644
@@ -866,6 +866,7 @@ dtb-$(CONFIG_ARCH_STI) += stih410-b2260.dtb
 dtb-$(CONFIG_STM32MP15x) += \
 	stm32mp157a-dk1.dtb \
 	stm32mp157a-avenger96.dtb \
+	stm32mp157c-dhcom-pdk2-u-boot.dtb \
 	stm32mp157c-dk2.dtb \
 	stm32mp157c-ed1.dtb \
 	stm32mp157c-ev1.dtb
arch/arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts new file +7 -0
new file mode 100644
index 0000000000..fd99988570
@@ -0,0 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2019 Marek Vasut <[email protected]>
+ */
+
+#include "stm32mp157c-dhcom-pdk2.dts"
+#include "stm32mp157c-dhcom-u-boot.dtsi"
arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +88 -0

88 lines not on this page · raw message

arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi new file +238 -0

238 lines not on this page · raw message

arch/arm/dts/stm32mp157c-dhcom.dtsi new file +379 -0

379 lines not on this page · raw message

arch/arm/mach-stm32mp/Kconfig +9 -0
index 137178aa45..e4d621dee8 100644
@@ -73,6 +73,14 @@ config TARGET_ST_STM32MP15x
 		Evalulation board (EV1) or Discovery board (DK1 and DK2).
 		The difference between board are managed with devicetree
 
+config TARGET_DH_STM32MP1_PDK2
+	bool "DH STM32MP1 PDK2"
+	select STM32MP15x
+	imply BOOTCOUNT_LIMIT
+	imply CMD_BOOTCOUNT
+	help
+		Target the DH PDK2 development kit with STM32MP15x SoM.
+
 endchoice
 
 config STM32MP1_TRUSTED
@@ -158,5 +166,6 @@ config DEBUG_UART_CLOCK
 endif
 
 source "board/st/stm32mp1/Kconfig"
+source "board/dhelectronics/dh_stm32mp1/Kconfig"
 
 endif
board/dhelectronics/dh_stm32mp1/Kconfig new file +21 -0
new file mode 100644
index 0000000000..8eab986640
@@ -0,0 +1,21 @@
+if TARGET_DH_STM32MP1_PDK2
+
+config SYS_BOARD
+	default "dh_stm32mp1"
+
+config SYS_VENDOR
+	default "dhelectronics"
+
+config SYS_CONFIG_NAME
+	default "stm32mp1"
+
+config ENV_SECT_SIZE
+	default 0x10000 if ENV_IS_IN_SPI_FLASH
+
+config ENV_OFFSET
+	default 0x1E0000 if ENV_IS_IN_SPI_FLASH
+
+config ENV_OFFSET_REDUND
+	default 0x1F0000 if ENV_IS_IN_SPI_FLASH
+
+endif
board/dhelectronics/dh_stm32mp1/MAINTAINERS new file +7 -0
new file mode 100644
index 0000000000..38f54a3da4
@@ -0,0 +1,7 @@
+DH_STM32MP1_PDK2 BOARD
+M:	Marek Vasut <[email protected]>
+S:	Maintained
+F:	arch/arm/dts/stm32mp157c-dhcom*
+F:	board/dhelectronics/dh_stm32mp1/
+F:	configs/stm32mp15_dhcom_basic_defconfig
+F:	include/configs/stm32mp1.h
board/dhelectronics/dh_stm32mp1/Makefile new file +12 -0
new file mode 100644
index 0000000000..a9d28218ef
@@ -0,0 +1,12 @@
+# SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+#
+# Copyright (C) 2018, STMicroelectronics - All Rights Reserved
+#
+
+ifdef CONFIG_SPL_BUILD
+obj-y += ../../st/stm32mp1/spl.o
+else
+obj-$(CONFIG_CMD_STBOARD) += ../../st/stm32mp1/cmd_stboard.o
+endif
+
+obj-y += ../../st/stm32mp1/board.o board.o
board/dhelectronics/dh_stm32mp1/board.c new file +778 -0

778 lines not on this page · raw message

configs/stm32mp15_dhcom_basic_defconfig new file +138 -0

138 lines not on this page · raw message

Signature · 1 line
2.24.1
#1 lore raw

PATCH v2 1/1 ARM: dts: stm32: Add DH Electronics DHCOM SoM and PDK2 board

Hi Marek,

Quoted 10 lines

From: Marek Vasut <[email protected]>
Sent: mardi 21 janvier 2020 22:39

Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier board. This is an SoM with STM32MP157C and an evaluation kit. The baseboard provides Ethernet, UART, USB, CAN and optional display.

Cc Patrick Delaunay <[email protected]>
Cc Patrice Chotard <[email protected]>

Few remarks (see after) about
1/ name of dts file (I prefer to don't add a file "-u-boot.dts")
2/ stusb1600 support (it seens that the PDK2 board hav no this USB type C controller, so part of code can be dropped) 3/ ST board specific part are not needed : OTP_BOARD / command stboard

But anayway:

I propose something for the first point on the custodians git, branch "dh"
https://gitlab.denx.de/u-boot/custodians/u-boot-stm.git

see " fixup! ARM: dts: stm32: Add DH Electronics DHCOM SoM and PDK2 board" on dh branch

Are you are ok with this proposal ?

In the same branch I propose 2 other modifications to reduce the size of board.c (remove feature note needed).

- remove stusb1600 support
- remove OTP_BOARD support and cmd_stboard

Regards

Patrick

Quoted 16 lines

---
V2: Rebase on u-boot/master and multi-board changes.

---
 arch/arm/dts/Makefile                         |   1 +
 .../arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts |   7 +
 arch/arm/dts/stm32mp157c-dhcom-pdk2.dts       |  88 ++
 arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi    | 238 ++++++
 arch/arm/dts/stm32mp157c-dhcom.dtsi           | 379 +++++++++
 arch/arm/mach-stm32mp/Kconfig                 |   9 +
 board/dhelectronics/dh_stm32mp1/Kconfig       |  21 +
 board/dhelectronics/dh_stm32mp1/MAINTAINERS   |   7 +
 board/dhelectronics/dh_stm32mp1/Makefile      |  12 +
 board/dhelectronics/dh_stm32mp1/board.c       | 778 ++++++++++++++++++
 configs/stm32mp15_dhcom_basic_defconfig       | 138 ++++
 11 files changed, 1678 insertions(+)
 create mode 100644 arch/arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts

I prefer to use the directly dts name from kernel.

And "stm32mp157c-dhcom-pdk2-u-boot.dtsi" is automatically included when stm32mp157c-dhcom-pdk2.dtb is compiled (by ./scripts/Makefile.lib:166)

Quoted 14 lines
 create mode 100644 arch/arm/dts/stm32mp157c-dhcom-pdk2.dts
 create mode 100644 arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi
 create mode 100644 arch/arm/dts/stm32mp157c-dhcom.dtsi
 create mode 100644 board/dhelectronics/dh_stm32mp1/Kconfig
 create mode 100644 board/dhelectronics/dh_stm32mp1/MAINTAINERS
 create mode 100644 board/dhelectronics/dh_stm32mp1/Makefile
 create mode 100644 board/dhelectronics/dh_stm32mp1/board.c
 create mode 100644 configs/stm32mp15_dhcom_basic_defconfig
arch/arm/dts/Makefile index renamed from arch/arm/dts/Makefile +0 -0

e469d191fb..cf0c75e006 100644

arch/arm/dts/Makefile dtb-$(CONFIG_ARCH_STI) += stih410-b2260.dtb · line 869

Quoted 4 lines
arch/arm/dts/Makefile +1 -0
@@ -866,6 +866,7 @@ dtb-$(CONFIG_ARCH_STI) += stih410-b2260.dtb
 dtb-$(CONFIG_STM32MP15x) += \
 	stm32mp157a-dk1.dtb \
 	stm32mp157a-avenger96.dtb \
+	stm32mp157c-dhcom-pdk2-u-boot.dtb \

+ stm32mp157c-dhcom-pdk2.dtb

Quoted 10 lines
arch/arm/dts/Makefile +0 -0
 	stm32mp157c-dk2.dtb \
 	stm32mp157c-ed1.dtb \
 	stm32mp157c-ev1.dtb
arch/arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts new file +0 -0
new file mode 100644
index 0000000000..fd99988570

arch/arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts line 6

Quoted 6 lines
arch/arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts new file +6 -0
@@ -0,0 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2019 Marek Vasut <[email protected]>  */
+
+#include "stm32mp157c-dhcom-pdk2.dts"
+#include "stm32mp157c-dhcom-u-boot.dtsi"

+#include "stm32mp157c-dhcom-pdk2.dts"
-#include "stm32mp157c-dhcom-u-boot.dtsi"

Quoted 816 lines
arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +8 -0
new file mode 100644
index 0000000000..05aa545f55
@@ -0,0 +1,88 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2019 Marek Vasut <[email protected]>  */
+
+#include "stm32mp157c-dhcom.dtsi"
+
+/ {
+	model = "STMicroelectronics STM32MP157C DHCOM Premium

Developer Kit (2)";

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +48 -0
+	compatible = "dh,stm32mp157c-dhcom-pdk2", "st,stm32mp157";
+
+	aliases {
+		serial0 = &uart4;
+		ethernet0 = &ethernet0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	ethernet_vio: vioregulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vio";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpiog 3 GPIO_ACTIVE_LOW>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&ethernet0 {
+	status = "okay";
+	pinctrl-0 = <&ethernet0_rmii_pins_a>;
+	pinctrl-1 = <&ethernet0_rmii_pins_sleep_a>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rmii";
+	max-speed = <100>;
+	phy-handle = <&phy0>;
+	st,eth_ref_clk_sel;
+	phy-reset-gpios = <&gpioh 15 GPIO_ACTIVE_LOW>;
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+
+		phy0: ethernet-phy at 1 {
+			reg = <1>;
+		};
+	};
+};
+
+&pinctrl {
+	ethernet0_rmii_pins_a: rmii-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 13, AF11)>, /*

ETH1_RMII_TXD0 */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('G', 14, AF11)>, /*

ETH1_RMII_TXD1 */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('B', 11, AF11)>, /*

ETH1_RMII_TX_EN */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('A', 1, AF0)>,   /*

ETH1_RMII_REF_CLK */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('A', 2, AF11)>,  /* ETH1_MDIO

*/

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('C', 1, AF11)>;  /* ETH1_MDC

*/

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +6 -0
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <2>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('C', 4, AF11)>,  /*

ETH1_RMII_RXD0 */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('C', 5, AF11)>,  /*

ETH1_RMII_RXD1 */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('A', 7, AF11)>;  /*

ETH1_RMII_CRS_DV */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +7 -0
+			bias-disable;
+		};
+	};
+
+	ethernet0_rmii_pins_sleep_a: rmii-sleep-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 13, ANALOG)>, /*

ETH1_RMII_TXD0 */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('G', 14, ANALOG)>, /*

ETH1_RMII_TXD1 */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('B', 11, ANALOG)>, /*

ETH1_RMII_TX_EN */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('A', 2, ANALOG)>,  /*

ETH1_MDIO */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('C', 1, ANALOG)>,  /*

ETH1_MDC */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('C', 4, ANALOG)>,  /*

ETH1_RMII_RXD0 */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('C', 5, ANALOG)>,  /*

ETH1_RMII_RXD1 */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('A', 1, ANALOG)>,  /*

ETH1_RMII_REF_CLK */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('A', 7, ANALOG)>;  /*

ETH1_RMII_CRS_DV */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +3 -0
+		};
+	};
+};
arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi new file +237 -0
new file mode 100644
index 0000000000..320912edd8
@@ -0,0 +1,238 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2019 Marek Vasut <[email protected]>  */
+
+#include <dt-bindings/clock/stm32mp1-clksrc.h>
+#include "stm32mp157-u-boot.dtsi"
+#include "stm32mp15-ddr3-2x4Gb-1066-binG.dtsi"
+
+/ {
+	aliases {
+		i2c1 = &i2c2;
+		i2c3 = &i2c4;
+		i2c4 = &i2c5;
+		mmc0 = &sdmmc1;
+		mmc1 = &sdmmc2;
+		spi0 = &qspi;
+		usb0 = &usbotg_hs;
+	};
+
+	config {
+		u-boot,boot-led = "heartbeat";
+		u-boot,error-led = "error";
+		st,fastboot-gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
+		st,stm32prog-gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
+	};
+
+	led {
+		red {
+			label = "error";
+			gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+			status = "okay";
+		};
+
+		blue {
+			default-state = "on";
+		};
+	};
+};
+
+&i2c4 {
+	u-boot,dm-pre-reloc;
+};
+
+&i2c4_pins_a {
+	u-boot,dm-pre-reloc;
+	pins {
+		u-boot,dm-pre-reloc;
+	};
+};
+
+&pmic {
+	u-boot,dm-pre-reloc;
+};
+
+&flash0 {
+	u-boot,dm-spl;
+};
+
+&qspi {
+	u-boot,dm-spl;
+};
+
+&qspi_clk_pins_a {
+	u-boot,dm-spl;
+	pins {
+		u-boot,dm-spl;
+	};
+};
+
+&qspi_bk1_pins_a {
+	u-boot,dm-spl;
+	pins1 {
+		u-boot,dm-spl;
+	};
+	pins2 {
+		u-boot,dm-spl;
+	};
+};
+
+&qspi_bk2_pins_a {
+	u-boot,dm-spl;
+	pins1 {
+		u-boot,dm-spl;
+	};
+	pins2 {
+		u-boot,dm-spl;
+	};
+};
+
+&rcc {
+	st,clksrc = <
+		CLK_MPU_PLL1P
+		CLK_AXI_PLL2P
+		CLK_MCU_PLL3P
+		CLK_PLL12_HSE
+		CLK_PLL3_HSE
+		CLK_PLL4_HSE
+		CLK_RTC_LSE
+		CLK_MCO1_DISABLED
+		CLK_MCO2_DISABLED
+	>;
+
+	st,clkdiv = <
+		1 /*MPU*/
+		0 /*AXI*/
+		0 /*MCU*/
+		1 /*APB1*/
+		1 /*APB2*/
+		1 /*APB3*/
+		1 /*APB4*/
+		2 /*APB5*/
+		23 /*RTC*/
+		0 /*MCO1*/
+		0 /*MCO2*/
+	>;
+
+	st,pkcs = <
+		CLK_CKPER_HSE
+		CLK_FMC_ACLK
+		CLK_QSPI_ACLK
+		CLK_ETH_PLL4P
+		CLK_SDMMC12_PLL4P
+		CLK_DSI_DSIPLL
+		CLK_STGEN_HSE
+		CLK_USBPHY_HSE
+		CLK_SPI2S1_PLL3Q
+		CLK_SPI2S23_PLL3Q
+		CLK_SPI45_HSI
+		CLK_SPI6_HSI
+		CLK_I2C46_HSI
+		CLK_SDMMC3_PLL4P
+		CLK_USBO_USBPHY
+		CLK_ADC_CKPER
+		CLK_CEC_LSE
+		CLK_I2C12_HSI
+		CLK_I2C35_HSI
+		CLK_UART1_HSI
+		CLK_UART24_HSI
+		CLK_UART35_HSI
+		CLK_UART6_HSI
+		CLK_UART78_HSI
+		CLK_SPDIF_PLL4P
+		CLK_FDCAN_PLL4Q
+		CLK_SAI1_PLL3Q
+		CLK_SAI2_PLL3Q
+		CLK_SAI3_PLL3Q
+		CLK_SAI4_PLL3Q
+		CLK_RNG1_LSI
+		CLK_RNG2_LSI
+		CLK_LPTIM1_PCLK1
+		CLK_LPTIM23_PCLK3
+		CLK_LPTIM45_LSE
+	>;
+
+	/* VCO = 1300.0 MHz => P = 650 (CPU) */
+	pll1: st,pll at 0 {
+		cfg = < 2 80 0 0 0 PQR(1,0,0) >;
+		frac = < 0x800 >;
+		u-boot,dm-pre-reloc;
+	};
+
+	/* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU), R = 533 (DDR) */
+	pll2: st,pll at 1 {
+		cfg = < 2 65 1 0 0 PQR(1,1,1) >;
+		frac = < 0x1400 >;
+		u-boot,dm-pre-reloc;
+	};
+
+	/* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */
+	pll3: st,pll at 2 {
+		cfg = < 1 33 1 16 36 PQR(1,1,1) >;
+		frac = < 0x1a04 >;
+		u-boot,dm-pre-reloc;
+	};
+
+	/* VCO = 600.0 MHz => P = 50, Q = 50, R = 50 */
+	pll4: st,pll at 3 {
+		cfg = < 1 49 11 11 11 PQR(1,1,1) >;
+		u-boot,dm-pre-reloc;
+	};
+};
+
+&sdmmc1 {
+	u-boot,dm-spl;
+};
+
+&sdmmc1_b4_pins_a {
+	u-boot,dm-spl;
+	pins {
+		u-boot,dm-spl;
+	};
+};
+
+&sdmmc1_dir_pins_a {
+	u-boot,dm-spl;
+	pins1 {
+		u-boot,dm-spl;
+	};
+	pins2 {
+		u-boot,dm-spl;
+	};
+};
+
+&sdmmc2 {
+	u-boot,dm-spl;
+};
+
+&sdmmc2_b4_pins_a {
+	u-boot,dm-spl;
+	pins {
+		u-boot,dm-spl;
+	};
+};
+
+&sdmmc2_d47_pins_a {
+	u-boot,dm-spl;
+	pins {
+		u-boot,dm-spl;
+	};
+};
+
+&uart4 {
+	u-boot,dm-pre-reloc;
+};
+
+&uart4_pins_a {
+	u-boot,dm-pre-reloc;
+	pins1 {
+		u-boot,dm-pre-reloc;
+	};
+	pins2 {
+		u-boot,dm-pre-reloc;
+		/* pull-up on rx to avoid floating level */
+		bias-pull-up;
+	};
+};
arch/arm/dts/stm32mp157c- renamed from arch/arm/dts/stm32mp157c-dhcom.dtsi +0 -0

dhcom.dtsi
new file mode 100644
index 0000000000..96661ae783

arch/arm/dts/stm32mp157c-dhcom.dtsi new file +228 -0
@@ -0,0 +1,379 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2019 Marek Vasut <[email protected]>  */ /dts-v1/;
+
+#include "stm32mp157c.dtsi"
+#include "stm32mp157xaa-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+	memory at c0000000 {
+		device_type = "memory";
+		reg = <0xC0000000 0x40000000>;
+	};
+};
+
+&cec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&cec_pins_a>;
+	status = "okay";
+};
+
+&dcmi {
+	status = "okay";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&dcmi_pins_a>;
+	pinctrl-1 = <&dcmi_sleep_pins_a>;
+};
+
+&dts {
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+};
+
+&i2c4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c4_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	pmic: stpmic at 33 {
+		compatible = "st,stpmic1";
+		reg = <0x33>;
+		interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		status = "okay";
+
+		regulators {
+			compatible = "st,stpmic1-regulators";
+			ldo1-supply = <&v3v3>;
+			ldo2-supply = <&v3v3>;
+			ldo3-supply = <&vdd_ddr>;
+			ldo5-supply = <&v3v3>;
+			ldo6-supply = <&v3v3>;
+			pwr_sw1-supply = <&bst_out>;
+			pwr_sw2-supply = <&bst_out>;
+
+			vddcore: buck1 {
+				regulator-name = "vddcore";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd_ddr: buck2 {
+				regulator-name = "vdd_ddr";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd: buck3 {
+				regulator-name = "vdd";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				st,mask-reset;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			v3v3: buck4 {
+				regulator-name = "v3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+				regulator-initial-mode = <0>;
+			};
+
+			vdda: ldo1 {
+				regulator-name = "vdda";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO1 0>;
+			};
+
+			v2v8: ldo2 {
+				regulator-name = "v2v8";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				interrupts = <IT_CURLIM_LDO2 0>;
+			};
+
+			vtt_ddr: ldo3 {
+				regulator-name = "vtt_ddr";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <750000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			vdd_usb: ldo4 {
+				regulator-name = "vdd_usb";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				interrupts = <IT_CURLIM_LDO4 0>;
+			};
+
+			vdd_sd: ldo5 {
+				regulator-name = "vdd_sd";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO5 0>;
+				regulator-boot-on;
+			};
+
+			v1v8: ldo6 {
+				regulator-name = "v1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				interrupts = <IT_CURLIM_LDO6 0>;
+			};
+
+			vref_ddr: vref_ddr {
+				regulator-name = "vref_ddr";
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			 bst_out: boost {
+				regulator-name = "bst_out";
+				interrupts = <IT_OCP_BOOST 0>;
+			 };
+
+			vbus_otg: pwr_sw1 {
+				regulator-name = "vbus_otg";
+				interrupts = <IT_OCP_OTG 0>;
+			 };
+
+			 vbus_sw: pwr_sw2 {
+				regulator-name = "vbus_sw";
+				interrupts = <IT_OCP_SWOUT 0>;
+				regulator-active-discharge;
+			 };
+		};
+
+		onkey {
+			compatible = "st,stpmic1-onkey";
+			interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
+			interrupt-names = "onkey-falling", "onkey-rising";
+			power-off-time-sec = <10>;
+			status = "okay";
+		};
+
+		watchdog {
+			compatible = "st,stpmic1-wdt";
+			status = "disabled";
+		};
+	};
+
+	eeprom at 50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+};
+
+&i2c5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c5_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+};
+
+&ipcc {
+	status = "okay";
+};
+
+&iwdg2 {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&m4_rproc {
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
+	mbox-names = "vq0", "vq1", "shutdown";
+	status = "okay";
+};
+
+&pwr {
+	pwr-regulators {
+		vdd-supply = <&vdd>;
+		vdd_3v3_usbfs-supply = <&vdd_usb>;
+	};
+};
+
+&qspi {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a &qspi_bk2_pins_a>;
+	pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a

&qspi_bk2_sleep_pins_a>;

arch/arm/dts/stm32mp157c-dhcom.dtsi new file +149 -0
+	reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	flash0: mx66l51235l at 0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+
+	flash1: mx66l51235l at 1 {
+		compatible = "jedec,spi-nor";
+		reg = <1>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
+&rng1 {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_a>;
+	broken-cd;
+	st,sig-dir;
+	st,neg-edge;
+	st,use-ckin;
+	bus-width = <4>;
+	vmmc-supply = <&vdd_sd>;
+	status = "okay";
+};
+
+&sdmmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	st,sig-dir;
+	st,neg-edge;
+	bus-width = <8>;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi1_pins_a>;
+	status = "disabled";
+};
+
+&timers2 {
+	/* spare dmas for other usage (un-delete to enable pwm capture) */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm2_pins_a>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+	timer at 1 {
+		status = "okay";
+	};
+};
+
+&timers6 {
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	timer at 5 {
+		status = "okay";
+	};
+};
+
+&timers8 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm8_pins_a>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+	timer at 7 {
+		status = "okay";
+	};
+};
+
+&timers12 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm12_pins_a>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+	timer at 11 {
+		status = "okay";
+	};
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins_a>;
+	status = "okay";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	phy-names = "usb";
+	status = "okay";
+};
+
+&usbotg_hs {
+	dr_mode = "peripheral";
+	phys = <&usbphyc_port1 0>;
+	phy-names = "usb2-phy";
+	vbus-supply = <&vbus_otg>;
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
arch/arm/mach-stm32mp/Kconfig +9 -0
index 137178aa45..e4d621dee8 100644
@@ -73,6 +73,14 @@ config TARGET_ST_STM32MP15x
 		Evalulation board (EV1) or Discovery board (DK1 and DK2).
 		The difference between board are managed with devicetree
 
+config TARGET_DH_STM32MP1_PDK2
+	bool "DH STM32MP1 PDK2"
+	select STM32MP15x
+	imply BOOTCOUNT_LIMIT
+	imply CMD_BOOTCOUNT
+	help
+		Target the DH PDK2 development kit with STM32MP15x SoM.
+
 endchoice
 
 config STM32MP1_TRUSTED
@@ -158,5 +166,6 @@ config DEBUG_UART_CLOCK  endif
 
 source "board/st/stm32mp1/Kconfig"
+source "board/dhelectronics/dh_stm32mp1/Kconfig"
 
 endif
board/dhelectronics/dh_stm32mp1/Kconfig new file +21 -0
new file mode 100644
index 0000000000..8eab986640
@@ -0,0 +1,21 @@
+if TARGET_DH_STM32MP1_PDK2
+
+config SYS_BOARD
+	default "dh_stm32mp1"
+
+config SYS_VENDOR
+	default "dhelectronics"
+
+config SYS_CONFIG_NAME
+	default "stm32mp1"
+
+config ENV_SECT_SIZE
+	default 0x10000 if ENV_IS_IN_SPI_FLASH
+
+config ENV_OFFSET
+	default 0x1E0000 if ENV_IS_IN_SPI_FLASH
+
+config ENV_OFFSET_REDUND
+	default 0x1F0000 if ENV_IS_IN_SPI_FLASH
+
+endif
board/dhelectronics/dh_stm32mp1/MAINTAINERS new file +7 -0
new file mode 100644
index 0000000000..38f54a3da4
@@ -0,0 +1,7 @@
+DH_STM32MP1_PDK2 BOARD
+M:	Marek Vasut <[email protected]>
+S:	Maintained
+F:	arch/arm/dts/stm32mp157c-dhcom*
+F:	board/dhelectronics/dh_stm32mp1/
+F:	configs/stm32mp15_dhcom_basic_defconfig
+F:	include/configs/stm32mp1.h
board/dhelectronics/dh_stm32mp1/Makefile new file +0 -0
new file mode 100644
index 0000000000..a9d28218ef

board/dhelectronics/dh_stm32mp1/Makefile line 7

Quoted 7 lines
board/dhelectronics/dh_stm32mp1/Makefile new file +7 -0
@@ -0,0 +1,12 @@
+# SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause # # Copyright (C)
+2018, STMicroelectronics - All Rights Reserved #
+
+ifdef CONFIG_SPL_BUILD
+obj-y += ../../st/stm32mp1/spl.o
+else
+obj-$(CONFIG_CMD_STBOARD) += ../../st/stm32mp1/cmd_stboard.o endif

Do you really need to have the STMicroelectornics specific "stboard" command for dh som/board ?

Quoted 152 lines
board/dhelectronics/dh_stm32mp1/Makefile new file +2 -0
+
+obj-y += ../../st/stm32mp1/board.o board.o
board/dhelectronics/dh_stm32mp1/board.c new file +95 -0
new file mode 100644
index 0000000000..0bf6b116ca
@@ -0,0 +1,778 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2018, STMicroelectronics - All Rights Reserved  */
+
+#include <common.h>
+#include <adc.h>
+#include <asm/arch/stm32.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <bootm.h>
+#include <clk.h>
+#include <config.h>
+#include <dm.h>
+#include <dm/device.h>
+#include <dm/uclass.h>
+#include <env.h>
+#include <env_internal.h>
+#include <g_dnl.h>
+#include <generic-phy.h>
+#include <hang.h>
+#include <i2c.h>
+#include <i2c_eeprom.h>
+#include <init.h>
+#include <led.h>
+#include <memalign.h>
+#include <misc.h>
+#include <mtd.h>
+#include <mtd_node.h>
+#include <netdev.h>
+#include <phy.h>
+#include <power/regulator.h>
+#include <remoteproc.h>
+#include <reset.h>
+#include <syscon.h>
+#include <usb.h>
+#include <usb/dwc2_udc.h>
+#include <watchdog.h>
+
+/* SYSCFG registers */
+#define SYSCFG_BOOTR		0x00
+#define SYSCFG_PMCSETR		0x04
+#define SYSCFG_IOCTRLSETR	0x18
+#define SYSCFG_ICNR		0x1C
+#define SYSCFG_CMPCR		0x20
+#define SYSCFG_CMPENSETR	0x24
+#define SYSCFG_PMCCLRR		0x44
+
+#define SYSCFG_BOOTR_BOOT_MASK		GENMASK(2, 0)
+#define SYSCFG_BOOTR_BOOTPD_SHIFT	4
+
+#define SYSCFG_IOCTRLSETR_HSLVEN_TRACE		BIT(0)
+#define SYSCFG_IOCTRLSETR_HSLVEN_QUADSPI	BIT(1)
+#define SYSCFG_IOCTRLSETR_HSLVEN_ETH		BIT(2)
+#define SYSCFG_IOCTRLSETR_HSLVEN_SDMMC		BIT(3)
+#define SYSCFG_IOCTRLSETR_HSLVEN_SPI		BIT(4)
+
+#define SYSCFG_CMPCR_SW_CTRL		BIT(1)
+#define SYSCFG_CMPCR_READY		BIT(8)
+
+#define SYSCFG_CMPENSETR_MPU_EN		BIT(0)
+
+#define SYSCFG_PMCSETR_ETH_CLK_SEL	BIT(16)
+#define SYSCFG_PMCSETR_ETH_REF_CLK_SEL	BIT(17)
+
+#define SYSCFG_PMCSETR_ETH_SELMII	BIT(20)
+
+#define SYSCFG_PMCSETR_ETH_SEL_MASK	GENMASK(23, 21)
+#define SYSCFG_PMCSETR_ETH_SEL_GMII_MII	0
+#define SYSCFG_PMCSETR_ETH_SEL_RGMII	BIT(21)
+#define SYSCFG_PMCSETR_ETH_SEL_RMII	BIT(23)
+
+/*
+ * Get a global data pointer
+ */
+DECLARE_GLOBAL_DATA_PTR;
+
+int setup_mac_address(void)
+{
+	struct udevice *dev;
+	ofnode eeprom;
+	unsigned char enetaddr[6];
+	int ret;
+
+	ret = eth_env_get_enetaddr("ethaddr", enetaddr);
+	if (ret)	/* ethaddr is already set */
+		return 0;
+
+	eeprom = ofnode_path("/soc/i2c at 5c002000/eeprom at 50");
+	if (!ofnode_valid(eeprom)) {
+		printf("Invalid hardware path to EEPROM!\n");
+		return -ENODEV;
+	}
+
+	ret = uclass_get_device_by_ofnode(UCLASS_I2C_EEPROM, eeprom,

&dev);

board/dhelectronics/dh_stm32mp1/board.c new file +46 -0
+	if (ret) {
+		printf("Cannot find EEPROM!\n");
+		return ret;
+	}
+
+	ret = i2c_eeprom_read(dev, 0xfa, enetaddr, 0x6);
+	if (ret) {
+		printf("Error reading configuration EEPROM!\n");
+		return ret;
+	}
+
+	if (is_valid_ethaddr(enetaddr))
+		eth_env_set_enetaddr("ethaddr", enetaddr);
+
+	return 0;
+}
+
+int checkboard(void)
+{
+	int ret;
+	char *mode;
+	u32 otp;
+	struct udevice *dev;
+	const char *fdt_compat;
+	int fdt_compat_len;
+
+	if (IS_ENABLED(CONFIG_STM32MP1_OPTEE))
+		mode = "trusted with OP-TEE";
+	else if (IS_ENABLED(CONFIG_STM32MP1_TRUSTED))
+		mode = "trusted";
+	else
+		mode = "basic";
+
+	printf("Board: stm32mp1 in %s mode", mode);
+	fdt_compat = fdt_getprop(gd->fdt_blob, 0, "compatible",
+				 &fdt_compat_len);
+	if (fdt_compat && fdt_compat_len)
+		printf(" (%s)", fdt_compat);
+	puts("\n");
+
+	ret = uclass_get_device_by_driver(UCLASS_MISC,
+					  DM_GET_DRIVER(stm32mp_bsec),
+					  &dev);
+
+	if (!ret)
+		ret = misc_read(dev,

STM32_BSEC_SHADOW(BSEC_OTP_BOARD),

board/dhelectronics/dh_stm32mp1/board.c

Quoted 1 line
board/dhelectronics/dh_stm32mp1/board.c new file +1 -0
+				&otp, sizeof(otp));

The next lines about BSEC_OTP_BOARD and MBxxxx is only ST microelectronics board, it can be remove I think

Quoted 119 lines
board/dhelectronics/dh_stm32mp1/board.c new file +61 -0
+	if (ret > 0 && otp) {
+		printf("Board: MB%04x Var%d Rev.%c-%02d\n",
+		       otp >> 16,
+		       (otp >> 12) & 0xF,
+		       ((otp >> 8) & 0xF) - 1 + 'A',
+		       otp & 0xF);
+	}
+
+	return 0;
+}
+
+static void board_key_check(void)
+{
+#if defined(CONFIG_FASTBOOT) || defined(CONFIG_CMD_STM32PROG)
+	ofnode node;
+	struct gpio_desc gpio;
+	enum forced_boot_mode boot_mode = BOOT_NORMAL;
+
+	node = ofnode_path("/config");
+	if (!ofnode_valid(node)) {
+		debug("%s: no /config node?\n", __func__);
+		return;
+	}
+#ifdef CONFIG_FASTBOOT
+	if (gpio_request_by_name_nodev(node, "st,fastboot-gpios", 0,
+				       &gpio, GPIOD_IS_IN)) {
+		debug("%s: could not find a /config/st,fastboot-gpios\n",
+		      __func__);
+	} else {
+		if (dm_gpio_get_value(&gpio)) {
+			puts("Fastboot key pressed, ");
+			boot_mode = BOOT_FASTBOOT;
+		}
+
+		dm_gpio_free(NULL, &gpio);
+	}
+#endif
+#ifdef CONFIG_CMD_STM32PROG
+	if (gpio_request_by_name_nodev(node, "st,stm32prog-gpios", 0,
+				       &gpio, GPIOD_IS_IN)) {
+		debug("%s: could not find a /config/st,stm32prog-gpios\n",
+		      __func__);
+	} else {
+		if (dm_gpio_get_value(&gpio)) {
+			puts("STM32Programmer key pressed, ");
+			boot_mode = BOOT_STM32PROG;
+		}
+		dm_gpio_free(NULL, &gpio);
+	}
+#endif
+
+	if (boot_mode != BOOT_NORMAL) {
+		puts("entering download mode...\n");
+		clrsetbits_le32(TAMP_BOOT_CONTEXT,
+				TAMP_BOOT_FORCED_MASK,
+				boot_mode);
+	}
+#endif
+}
+
+#if defined(CONFIG_USB_GADGET) &&

defined(CONFIG_USB_GADGET_DWC2_OTG)

board/dhelectronics/dh_stm32mp1/board.c new file +25 -0
+
+/* STMicroelectronics STUSB1600 Type-C controller */
+#define STUSB1600_CC_CONNECTION_STATUS		0x0E
+
+/* STUSB1600_CC_CONNECTION_STATUS bitfields */
+#define STUSB1600_CC_ATTACH			BIT(0)
+
+static int stusb1600_init(struct udevice **dev_stusb1600) {
+	ofnode node;
+	struct udevice *dev, *bus;
+	int ret;
+	u32 chip_addr;
+
+	*dev_stusb1600 = NULL;
+
+	/* if node stusb1600 is present, means DK1 or DK2 board */
+	node = ofnode_by_compatible(ofnode_null(), "st,stusb1600");
+	if (!ofnode_valid(node))
+		return -ENODEV;
+
+	ret = ofnode_read_u32(node, "reg", &chip_addr);
+	if (ret)
+		return -EINVAL;
+
+	ret = uclass_get_device_by_ofnode(UCLASS_I2C,

ofnode_get_parent(node),

board/dhelectronics/dh_stm32mp1/board.c new file +17 -0
+					  &bus);
+	if (ret) {
+		printf("bus for stusb1600 not found\n");
+		return -ENODEV;
+	}
+
+	ret = dm_i2c_probe(bus, chip_addr, 0, &dev);
+	if (!ret)
+		*dev_stusb1600 = dev;
+
+	return ret;
+}
+
+static int stusb1600_cable_connected(struct udevice *dev) {
+	u8 status;
+
+	if (dm_i2c_read(dev, STUSB1600_CC_CONNECTION_STATUS, &status,

1))

board/dhelectronics/dh_stm32mp1/board.c new file +13 -0
+		return 0;
+
+	return status & STUSB1600_CC_ATTACH;
+}
+
+#include <usb/dwc2_udc.h>
+int g_dnl_board_usb_cable_connected(void)
+{
+	struct udevice *stusb1600;
+	struct udevice *dwc2_udc_otg;
+	int ret;
+
+	if (!stusb1600_init(&stusb1600))

board/dhelectronics/dh_stm32mp1/board.c line 271

Quoted 10 lines
board/dhelectronics/dh_stm32mp1/board.c new file +10 -0
+		return stusb1600_cable_connected(stusb1600);
+
+	ret = uclass_get_device_by_driver(UCLASS_USB_GADGET_GENERIC,
+					  DM_GET_DRIVER(dwc2_udc_otg),
+					  &dwc2_udc_otg);
+	if (!ret)
+		debug("dwc2_udc_otg init failed\n");
+
+	return dwc2_udc_B_session_valid(dwc2_udc_otg);
+}

All the stusb1600 can be removed (not present on PDK2 / DHCOM according device tree)

Quoted 237 lines
board/dhelectronics/dh_stm32mp1/board.c new file +7 -0
+#define STM32MP1_G_DNL_DFU_PRODUCT_NUM 0xdf11 #define
+STM32MP1_G_DNL_FASTBOOT_PRODUCT_NUM 0x0afb
+
+int g_dnl_bind_fixup(struct usb_device_descriptor *dev, const char
+*name) {
+	if (!strcmp(name, "usb_dnl_dfu"))
+		put_unaligned(STM32MP1_G_DNL_DFU_PRODUCT_NUM, &dev-
Quoted 1 line

idProduct);

board/dhelectronics/dh_stm32mp1/board.c new file +2 -0
+	else if (!strcmp(name, "usb_dnl_fastboot"))
+

put_unaligned(STM32MP1_G_DNL_FASTBOOT_PRODUCT_NUM,

board/dhelectronics/dh_stm32mp1/board.c new file +3 -0
+			      &dev->idProduct);
+	else
+		put_unaligned(CONFIG_USB_GADGET_PRODUCT_NUM, &dev-
Quoted 1 line

idProduct);

board/dhelectronics/dh_stm32mp1/board.c new file +91 -0
+
+	return 0;
+}
+
+#endif /* CONFIG_USB_GADGET */
+
+#ifdef CONFIG_LED
+static int get_led(struct udevice **dev, char *led_string) {
+	char *led_name;
+	int ret;
+
+	led_name = fdtdec_get_config_string(gd->fdt_blob, led_string);
+	if (!led_name) {
+		pr_debug("%s: could not find %s config string\n",
+			 __func__, led_string);
+		return -ENOENT;
+	}
+	ret = led_get_by_label(led_name, dev);
+	if (ret) {
+		debug("%s: get=%d\n", __func__, ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int setup_led(enum led_state_t cmd) {
+	struct udevice *dev;
+	int ret;
+
+	ret = get_led(&dev, "u-boot,boot-led");
+	if (ret)
+		return ret;
+
+	ret = led_set_state(dev, cmd);
+	return ret;
+}
+#endif
+
+static void __maybe_unused led_error_blink(u32 nb_blink) { #ifdef
+CONFIG_LED
+	int ret;
+	struct udevice *led;
+	u32 i;
+#endif
+
+	if (!nb_blink)
+		return;
+
+#ifdef CONFIG_LED
+	ret = get_led(&led, "u-boot,error-led");
+	if (!ret) {
+		/* make u-boot,error-led blinking */
+		/* if U32_MAX and 125ms interval, for 17.02 years */
+		for (i = 0; i < 2 * nb_blink; i++) {
+			led_set_state(led, LEDST_TOGGLE);
+			mdelay(125);
+			WATCHDOG_RESET();
+		}
+	}
+#endif
+
+	/* infinite: the boot process must be stopped */
+	if (nb_blink == U32_MAX)
+		hang();
+}
+
+static void sysconf_init(void)
+{
+#ifndef CONFIG_STM32MP1_TRUSTED
+	u8 *syscfg;
+#ifdef CONFIG_DM_REGULATOR
+	struct udevice *pwr_dev;
+	struct udevice *pwr_reg;
+	struct udevice *dev;
+	int ret;
+	u32 otp = 0;
+#endif
+	u32 bootr;
+
+	syscfg = (u8 *)syscon_get_first_range(STM32MP_SYSCON_SYSCFG);
+
+	/* interconnect update : select master using the port 1 */
+	/* LTDC = AXI_M9 */
+	/* GPU  = AXI_M8 */
+	/* today information is hardcoded in U-Boot */
+	writel(BIT(9), syscfg + SYSCFG_ICNR);
+
+	/* disable Pull-Down for boot pin connected to VDD */
+	bootr = readl(syscfg + SYSCFG_BOOTR);
+	bootr &= ~(SYSCFG_BOOTR_BOOT_MASK <<

SYSCFG_BOOTR_BOOTPD_SHIFT);

board/dhelectronics/dh_stm32mp1/board.c new file +1 -0
+	bootr |= (bootr & SYSCFG_BOOTR_BOOT_MASK) <<

SYSCFG_BOOTR_BOOTPD_SHIFT;

board/dhelectronics/dh_stm32mp1/board.c new file +4 -0
+	writel(bootr, syscfg + SYSCFG_BOOTR);
+
+#ifdef CONFIG_DM_REGULATOR
+	/* High Speed Low Voltage Pad mode Enable for SPI, SDMMC, ETH,

QSPI

board/dhelectronics/dh_stm32mp1/board.c new file +1 -0
+	 * and TRACE. Needed above ~50MHz and conditioned by AFMUX

selection.

board/dhelectronics/dh_stm32mp1/board.c new file +17 -0
+	 * The customer will have to disable this for low frequencies
+	 * or if AFMUX is selected but the function not used, typically for
+	 * TRACE. Otherwise, impact on power consumption.
+	 *
+	 * WARNING:
+	 *   enabling High Speed mode while VDD>2.7V
+	 *   with the OTP product_below_2v5 (OTP 18, BIT 13)
+	 *   erroneously set to 1 can damage the IC!
+	 *   => U-Boot set the register only if VDD < 2.7V (in DT)
+	 *      but this value need to be consistent with board design
+	 */
+	ret = uclass_get_device_by_driver(UCLASS_PMIC,
+					  DM_GET_DRIVER(stm32mp_pwr_pmic),
+					  &pwr_dev);
+	if (!ret) {
+		ret = uclass_get_device_by_driver(UCLASS_MISC,
+

DM_GET_DRIVER(stm32mp_bsec),

board/dhelectronics/dh_stm32mp1/board.c new file +19 -0
+						  &dev);
+		if (ret) {
+			pr_err("Can't find stm32mp_bsec driver\n");
+			return;
+		}
+
+		ret = misc_read(dev, STM32_BSEC_SHADOW(18), &otp, 4);
+		if (ret > 0)
+			otp = otp & BIT(13);
+
+		/* get VDD = vdd-supply */
+		ret = device_get_supply_regulator(pwr_dev, "vdd-supply",
+						  &pwr_reg);
+
+		/* check if VDD is Low Voltage */
+		if (!ret) {
+			if (regulator_get_value(pwr_reg) < 2700000) {
+				writel(SYSCFG_IOCTRLSETR_HSLVEN_TRACE |
+				       SYSCFG_IOCTRLSETR_HSLVEN_QUADSPI

|

board/dhelectronics/dh_stm32mp1/board.c new file +7 -0
+				       SYSCFG_IOCTRLSETR_HSLVEN_ETH |
+				       SYSCFG_IOCTRLSETR_HSLVEN_SDMMC |
+				       SYSCFG_IOCTRLSETR_HSLVEN_SPI,
+				       syscfg + SYSCFG_IOCTRLSETR);
+
+				if (!otp)
+					pr_err("product_below_2v5=0: HSLVEN

protected by HW\n");

board/dhelectronics/dh_stm32mp1/board.c new file +3 -0
+			} else {
+				if (otp)
+					pr_err("product_below_2v5=1: HSLVEN

update is destructive, no update as VDD>2.7V\n");

board/dhelectronics/dh_stm32mp1/board.c new file +11 -0
+			}
+		} else {
+			debug("VDD unknown");
+		}
+	}
+#endif
+
+	/* activate automatic I/O compensation
+	 * warning: need to ensure CSI enabled and ready in clock driver
+	 */
+	writel(SYSCFG_CMPENSETR_MPU_EN, syscfg +

SYSCFG_CMPENSETR);

board/dhelectronics/dh_stm32mp1/board.c new file +4 -0
+
+	while (!(readl(syscfg + SYSCFG_CMPCR) & SYSCFG_CMPCR_READY))
+		;
+	clrbits_le32(syscfg + SYSCFG_CMPCR, SYSCFG_CMPCR_SW_CTRL);

#endif }

board/dhelectronics/dh_stm32mp1/board.c new file +53 -0
+
+/* board dependent setup after realloc */ int board_init(void) {
+	struct udevice *dev;
+
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = STM32_DDR_BASE + 0x100;
+
+	/* probe all PINCTRL for hog */
+	for (uclass_first_device(UCLASS_PINCTRL, &dev);
+	     dev;
+	     uclass_next_device(&dev)) {
+		pr_debug("probe pincontrol = %s\n", dev->name);
+	}
+
+	board_key_check();
+
+#ifdef CONFIG_DM_REGULATOR
+	regulators_enable_boot_on(_DEBUG);
+#endif
+
+	sysconf_init();
+
+	if (CONFIG_IS_ENABLED(CONFIG_LED))
+		led_default_state();
+
+	return 0;
+}
+
+int board_late_init(void)
+{
+	char *boot_device;
+#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+	const void *fdt_compat;
+	int fdt_compat_len;
+	int ret;
+	u32 otp;
+	struct udevice *dev;
+	char buf[10];
+
+	fdt_compat = fdt_getprop(gd->fdt_blob, 0, "compatible",
+				 &fdt_compat_len);
+	if (fdt_compat && fdt_compat_len) {
+		if (strncmp(fdt_compat, "st,", 3) != 0)
+			env_set("board_name", fdt_compat);
+		else
+			env_set("board_name", fdt_compat + 3);
+	}
+	ret = uclass_get_device_by_driver(UCLASS_MISC,
+					  DM_GET_DRIVER(stm32mp_bsec),
+					  &dev);
+
+	if (!ret)
+		ret = misc_read(dev,

STM32_BSEC_SHADOW(BSEC_OTP_BOARD),

board/dhelectronics/dh_stm32mp1/board.c line 511

Quoted 9 lines
board/dhelectronics/dh_stm32mp1/board.c new file +9 -0
+				&otp, sizeof(otp));
+	if (!ret && otp) {
+		snprintf(buf, sizeof(buf), "0x%04x", otp >> 16);
+		env_set("board_id", buf);
+
+		snprintf(buf, sizeof(buf), "0x%04x",
+			 ((otp >> 8) & 0xF) - 1 + 0xA);
+		env_set("board_rev", buf);
+	}

Part on BSEC_OTP_BOARD can be removed (ST Microelectronics specific use of OTP).

Quoted 404 lines
board/dhelectronics/dh_stm32mp1/board.c new file +79 -0
+#endif
+
+	/* Check the boot-source to disable bootdelay */
+	boot_device = env_get("boot_device");
+	if (!strcmp(boot_device, "serial") || !strcmp(boot_device, "usb"))
+		env_set("bootdelay", "0");
+
+	return 0;
+}
+
+void board_quiesce_devices(void)
+{
+#ifdef CONFIG_LED
+	setup_led(LEDST_OFF);
+#endif
+}
+
+/* eth init function : weak called in eqos driver */ int
+board_interface_eth_init(struct udevice *dev,
+			     phy_interface_t interface_type) {
+	u8 *syscfg;
+	u32 value;
+	bool eth_clk_sel_reg = false;
+	bool eth_ref_clk_sel_reg = false;
+
+	/* Gigabit Ethernet 125MHz clock selection. */
+	eth_clk_sel_reg = dev_read_bool(dev, "st,eth_clk_sel");
+
+	/* Ethernet 50Mhz RMII clock selection */
+	eth_ref_clk_sel_reg =
+		dev_read_bool(dev, "st,eth_ref_clk_sel");
+
+	syscfg = (u8 *)syscon_get_first_range(STM32MP_SYSCON_SYSCFG);
+
+	if (!syscfg)
+		return -ENODEV;
+
+	switch (interface_type) {
+	case PHY_INTERFACE_MODE_MII:
+		value = SYSCFG_PMCSETR_ETH_SEL_GMII_MII |
+			SYSCFG_PMCSETR_ETH_REF_CLK_SEL;
+		debug("%s: PHY_INTERFACE_MODE_MII\n", __func__);
+		break;
+	case PHY_INTERFACE_MODE_GMII:
+		if (eth_clk_sel_reg)
+			value = SYSCFG_PMCSETR_ETH_SEL_GMII_MII |
+				SYSCFG_PMCSETR_ETH_CLK_SEL;
+		else
+			value = SYSCFG_PMCSETR_ETH_SEL_GMII_MII;
+		debug("%s: PHY_INTERFACE_MODE_GMII\n", __func__);
+		break;
+	case PHY_INTERFACE_MODE_RMII:
+		if (eth_ref_clk_sel_reg)
+			value = SYSCFG_PMCSETR_ETH_SEL_RMII |
+				SYSCFG_PMCSETR_ETH_REF_CLK_SEL;
+		else
+			value = SYSCFG_PMCSETR_ETH_SEL_RMII;
+		debug("%s: PHY_INTERFACE_MODE_RMII\n", __func__);
+		break;
+	case PHY_INTERFACE_MODE_RGMII:
+	case PHY_INTERFACE_MODE_RGMII_ID:
+	case PHY_INTERFACE_MODE_RGMII_RXID:
+	case PHY_INTERFACE_MODE_RGMII_TXID:
+		if (eth_clk_sel_reg)
+			value = SYSCFG_PMCSETR_ETH_SEL_RGMII |
+				SYSCFG_PMCSETR_ETH_CLK_SEL;
+		else
+			value = SYSCFG_PMCSETR_ETH_SEL_RGMII;
+		debug("%s: PHY_INTERFACE_MODE_RGMII\n", __func__);
+		break;
+	default:
+		debug("%s: Do not manage %d interface\n",
+		      __func__, interface_type);
+		/* Do not manage others interfaces */
+		return -EINVAL;
+	}
+
+	/* clear and set ETH configuration bits */
+	writel(SYSCFG_PMCSETR_ETH_SEL_MASK |

SYSCFG_PMCSETR_ETH_SELMII |

board/dhelectronics/dh_stm32mp1/board.c new file +1 -0
+	       SYSCFG_PMCSETR_ETH_REF_CLK_SEL |

SYSCFG_PMCSETR_ETH_CLK_SEL,

board/dhelectronics/dh_stm32mp1/board.c new file +167 -0
+	       syscfg + SYSCFG_PMCCLRR);
+	writel(value, syscfg + SYSCFG_PMCSETR);
+
+	return 0;
+}
+
+enum env_location env_get_location(enum env_operation op, int prio) {
+	if (prio)
+		return ENVL_UNKNOWN;
+
+#ifdef CONFIG_ENV_IS_IN_SPI_FLASH
+	return ENVL_SPI_FLASH;
+#else
+	return ENVL_NOWHERE;
+#endif
+}
+
+#ifdef CONFIG_SYS_MTDPARTS_RUNTIME
+
+#define MTDPARTS_LEN		256
+#define MTDIDS_LEN		128
+
+/**
+ * The mtdparts_nand0 and mtdparts_nor0 variable tends to be long.
+ * If we need to access it before the env is relocated, then we need
+ * to use our own stack buffer. gd->env_buf will be too small.
+ *
+ * @param buf temporary buffer pointer MTDPARTS_LEN long
+ * @return mtdparts variable string, NULL if not found  */ static const
+char *env_get_mtdparts(const char *str, char *buf) {
+	if (gd->flags & GD_FLG_ENV_READY)
+		return env_get(str);
+	if (env_get_f(str, buf, MTDPARTS_LEN) != -1)
+		return buf;
+
+	return NULL;
+}
+
+/**
+ * update the variables "mtdids" and "mtdparts" with content of
+mtdparts_<dev>  */ static void board_get_mtdparts(const char *dev,
+			       char *mtdids,
+			       char *mtdparts)
+{
+	char env_name[32] = "mtdparts_";
+	char tmp_mtdparts[MTDPARTS_LEN];
+	const char *tmp;
+
+	/* name of env variable to read = mtdparts_<dev> */
+	strcat(env_name, dev);
+	tmp = env_get_mtdparts(env_name, tmp_mtdparts);
+	if (tmp) {
+		/* mtdids: "<dev>=<dev>, ...." */
+		if (mtdids[0] != '\0')
+			strcat(mtdids, ",");
+		strcat(mtdids, dev);
+		strcat(mtdids, "=");
+		strcat(mtdids, dev);
+
+		/* mtdparts: "mtdparts=<dev>:<mtdparts_<dev>>;..." */
+		if (mtdparts[0] != '\0')
+			strncat(mtdparts, ";", MTDPARTS_LEN);
+		else
+			strcat(mtdparts, "mtdparts=");
+		strncat(mtdparts, dev, MTDPARTS_LEN);
+		strncat(mtdparts, ":", MTDPARTS_LEN);
+		strncat(mtdparts, tmp, MTDPARTS_LEN);
+	}
+}
+
+void board_mtdparts_default(const char **mtdids, const char **mtdparts)
+{
+	struct udevice *dev;
+	static char parts[3 * MTDPARTS_LEN + 1];
+	static char ids[MTDIDS_LEN + 1];
+	static bool mtd_initialized;
+
+	if (mtd_initialized) {
+		*mtdids = ids;
+		*mtdparts = parts;
+		return;
+	}
+
+	memset(parts, 0, sizeof(parts));
+	memset(ids, 0, sizeof(ids));
+
+	/* probe all MTD devices */
+	for (uclass_first_device(UCLASS_MTD, &dev);
+	     dev;
+	     uclass_next_device(&dev)) {
+		pr_debug("mtd device = %s\n", dev->name);
+	}
+
+	if (!uclass_get_device(UCLASS_SPI_FLASH, 0, &dev))
+		board_get_mtdparts("nor0", ids, parts);
+
+	mtd_initialized = true;
+	*mtdids = ids;
+	*mtdparts = parts;
+	debug("%s:mtdids=%s & mtdparts=%s\n", __func__, ids, parts); } #endif
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+int ft_board_setup(void *blob, bd_t *bd) {
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_SET_DFU_ALT_INFO
+#define DFU_ALT_BUF_LEN SZ_1K
+
+static void board_get_alt_info(const char *dev, char *buff) {
+	char var_name[32] = "dfu_alt_info_";
+	int ret;
+
+	ALLOC_CACHE_ALIGN_BUFFER(char, tmp_alt, DFU_ALT_BUF_LEN);
+
+	/* name of env variable to read = dfu_alt_info_<dev> */
+	strcat(var_name, dev);
+	ret = env_get_f(var_name, tmp_alt, DFU_ALT_BUF_LEN);
+	if (ret) {
+		if (buff[0] != '\0')
+			strcat(buff, "&");
+		strncat(buff, tmp_alt, DFU_ALT_BUF_LEN);
+	}
+}
+
+void set_dfu_alt_info(char *interface, char *devstr) {
+	struct udevice *dev;
+
+	ALLOC_CACHE_ALIGN_BUFFER(char, buf, DFU_ALT_BUF_LEN);
+
+	if (env_get("dfu_alt_info"))
+		return;
+
+	memset(buf, 0, sizeof(buf));
+
+	/* probe all MTD devices */
+	mtd_probe_devices();
+
+	board_get_alt_info("ram", buf);
+
+	if (!uclass_get_device(UCLASS_MMC, 0, &dev))
+		board_get_alt_info("mmc0", buf);
+
+	if (!uclass_get_device(UCLASS_MMC, 1, &dev))
+		board_get_alt_info("mmc1", buf);
+
+	if (!uclass_get_device(UCLASS_SPI_FLASH, 0, &dev))
+		board_get_alt_info("nor0", buf);
+
+	env_set("dfu_alt_info", buf);
+	puts("DFU alt info setting: done\n");
+}
+#endif
+
+static void board_copro_image_process(ulong fw_image, size_t fw_size) {
+	int ret, id = 0; /* Copro id fixed to 0 as only one coproc on mp1 */
+
+	if (!rproc_is_initialized())
+		if (rproc_init()) {
+			printf("Remote Processor %d initialization failed\n",
+			       id);
+			return;
+		}
+
+	ret = rproc_load(id, fw_image, fw_size);
+	printf("Load Remote Processor %d with data at addr=0x%08lx %u

bytes:%s\n",

board/dhelectronics/dh_stm32mp1/board.c new file +9 -0
+	       id, fw_image, fw_size, ret ? " Failed!" : " Success!");
+
+	if (!ret) {
+		rproc_start(id);
+		env_set("copro_state", "booted");
+	}
+}
+
+U_BOOT_FIT_LOADABLE_HANDLER(IH_TYPE_COPRO,

board_copro_image_process);

configs/stm32mp15_dhcom_basic_defconfig new file +53 -0
new file mode 100644
index 0000000000..58f9dbf7cc
@@ -0,0 +1,138 @@
+CONFIG_ARM=y
+CONFIG_ARCH_STM32MP=y
+CONFIG_SYS_MALLOC_F_LEN=0x3000
+CONFIG_ENV_SIZE=0x4000
+CONFIG_SPL_MMC_SUPPORT=y
+CONFIG_SPL=y
+CONFIG_TARGET_DH_STM32MP1_PDK2=y
+CONFIG_SPL_SPI_FLASH_SUPPORT=y
+CONFIG_SPL_SPI_SUPPORT=y
+# CONFIG_ARMV7_VIRT is not set
+CONFIG_SPL_TEXT_BASE=0x2FFC2500
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_FIT=y
+CONFIG_BOOTCOMMAND="run bootcmd_stm32mp"
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION=3
+CONFIG_SPL_I2C_SUPPORT=y
+CONFIG_SPL_MTD_SUPPORT=y
+CONFIG_SPL_POWER_SUPPORT=y
+CONFIG_SYS_SPI_U_BOOT_OFFS=0x80000
+CONFIG_SYS_PROMPT="STM32MP> "
+# CONFIG_CMD_BOOTD is not set
+# CONFIG_CMD_ELF is not set
+# CONFIG_CMD_IMI is not set
+# CONFIG_CMD_XIMG is not set
+# CONFIG_CMD_EXPORTENV is not set
+CONFIG_CMD_EEPROM=y
+CONFIG_CMD_MEMINFO=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_ADC=y
+CONFIG_CMD_CLK=y
+CONFIG_CMD_DFU=y
+CONFIG_CMD_FUSE=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_MTD=y
+CONFIG_CMD_REMOTEPROC=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
+CONFIG_CMD_BMP=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_TIMER=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_MTDPARTS=y
+# CONFIG_SPL_DOS_PARTITION is not set
+CONFIG_DEFAULT_DEVICE_TREE="stm32mp157c-dhcom-pdk2-u-boot"
+CONFIG_OF_SPL_REMOVE_PROPS="interrupts interrupt-names interrupts-

extended interrupt-controller \\\#interrupt-cells interrupt-parent dmas dma-names assigned-clocks assigned-clock-rates assigned-clock-parents hwlocks"

configs/stm32mp15_dhcom_basic_defconfig new file +38 -0
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_USE_ENV_SPI_BUS=y
+CONFIG_ENV_SPI_BUS=0
+CONFIG_USE_ENV_SPI_CS=y
+CONFIG_ENV_SPI_CS=0
+CONFIG_USE_ENV_SPI_MAX_HZ=y
+CONFIG_ENV_SPI_MAX_HZ=10000000
+CONFIG_USE_ENV_SPI_MODE=y
+CONFIG_ENV_SPI_MODE=0x0
+CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_IP_DEFRAG=y
+CONFIG_TFTP_BLOCKSIZE=1536
+CONFIG_STM32_ADC=y
+CONFIG_SPL_BLOCK_CACHE=y
+CONFIG_DFU_MMC=y
+CONFIG_DFU_RAM=y
+CONFIG_DFU_VIRT=y
+CONFIG_DM_HWSPINLOCK=y
+CONFIG_HWSPINLOCK_STM32=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_STM32F7=y
+CONFIG_LED=y
+CONFIG_LED_GPIO=y
+CONFIG_DM_MAILBOX=y
+CONFIG_STM32_IPCC=y
+CONFIG_I2C_EEPROM=y
+CONFIG_DM_MMC=y
+CONFIG_SUPPORT_EMMC_BOOT=y
+CONFIG_STM32_SDMMC2=y
+CONFIG_MTD=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_SPI_FLASH_WINBOND=y
+# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set

CONFIG_SPI_FLASH_MTD=y
+CONFIG_SPL_SPI_FLASH_MTD=y CONFIG_DM_ETH=y
CONFIG_DWC_ETH_QOS=y

configs/stm32mp15_dhcom_basic_defconfig new file +5 -0
+CONFIG_PHY=y CONFIG_PHY_STM32_USBPHYC=y CONFIG_PINCONF=y #
+CONFIG_SPL_PINCTRL_FULL is not set CONFIG_PINCTRL_STMFX=y
+CONFIG_DM_PMIC=y # CONFIG_SPL_PMIC_CHILDREN is not set
+CONFIG_PMIC_STPMIC1=y CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y

CONFIG_DM_REGULATOR_STM32_VREFBUF=y

configs/stm32mp15_dhcom_basic_defconfig new file +32 -1
+CONFIG_DM_REGULATOR_STPMIC1=y
+CONFIG_REMOTEPROC_STM32_COPRO=y
+CONFIG_DM_RTC=y
+CONFIG_RTC_STM32=y
+CONFIG_SERIAL_RX_BUFFER=y
+CONFIG_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_STM32_QSPI=y
+CONFIG_STM32_SPI=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_DM_USB_GADGET=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_GENERIC=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_MANUFACTURER="dh"
+CONFIG_USB_GADGET_VENDOR_NUM=0x0483
+CONFIG_USB_GADGET_PRODUCT_NUM=0x5720
+CONFIG_USB_GADGET_DWC2_OTG=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_USB_HOST_ETHER=y
+CONFIG_USB_ETHER_ASIX=y
+CONFIG_DM_VIDEO=y
+CONFIG_BACKLIGHT_GPIO=y
+CONFIG_VIDEO_LCD_ORISETECH_OTM8009A=y
+CONFIG_VIDEO_LCD_RAYDIUM_RM68200=y
+CONFIG_VIDEO_STM32=y
+CONFIG_VIDEO_STM32_DSI=y
+CONFIG_VIDEO_STM32_MAX_XRES=1280
+CONFIG_VIDEO_STM32_MAX_YRES=800
+CONFIG_LZO=y
+CONFIG_FDT_FIXUP_PARTITIONS=y
--

2.24.1

#2 lore raw

PATCH v2 1/1 ARM: dts: stm32: Add DH Electronics DHCOM SoM and PDK2 board

Quoted 1 line · Patrick DELAUNAY

Hi Marek,

Hi,

Quoted 16 lines
Quoted 10 lines

From: Marek Vasut <[email protected]>
Sent: mardi 21 janvier 2020 22:39

Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier board. This is an SoM with STM32MP157C and an evaluation kit. The baseboard provides Ethernet, UART, USB, CAN and optional display.

Cc Patrick Delaunay <[email protected]>
Cc Patrice Chotard <[email protected]>

Few remarks (see after) about
1/ name of dts file (I prefer to don't add a file "-u-boot.dts")
2/ stusb1600 support (it seens that the PDK2 board hav no this USB type C controller, so part of code can be dropped) 3/ ST board specific part are not needed : OTP_BOARD / command stboard

Quoted 8 lines

But anayway:

I propose something for the first point on the custodians git, branch "dh"
https://gitlab.denx.de/u-boot/custodians/u-boot-stm.git

see " fixup! ARM: dts: stm32: Add DH Electronics DHCOM SoM and PDK2 board" on dh branch

Did you verify that the generated DT is identical for U-Boot and SPL before and after this change ?

Quoted 7 lines

Are you are ok with this proposal ?

In the same branch I propose 2 other modifications to reduce the size of board.c (remove feature note needed).

- remove stusb1600 support
- remove OTP_BOARD support and cmd_stboard

These two are OK, thanks.

Signature · 2 lines
Best regards,
Marek Vasut
#3 lore raw

PATCH v2 1/1 ARM: dts: stm32: Add DH Electronics DHCOM SoM and PDK2 board

Hi Marek

Quoted 29 lines

From: Marek Vasut <[email protected]>
Sent: jeudi 23 janvier 2020 23:45

Quoted 1 line · Patrick DELAUNAY

Hi Marek,

Hi,

Quoted 21 lines
Quoted 10 lines

From: Marek Vasut <[email protected]>
Sent: mardi 21 janvier 2020 22:39

Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier board. This is an SoM with STM32MP157C and an evaluation kit. The baseboard provides Ethernet, UART, USB, CAN and optional display.

Cc Patrick Delaunay <[email protected]>
Cc Patrice Chotard <[email protected]>

Few remarks (see after) about
1/ name of dts file (I prefer to don't add a file "-u-boot.dts") 2/ stusb1600 support (it seens that the PDK2 board hav no this USB type C controller, so part of code can be dropped) 3/ ST board specific part are not needed : OTP_BOARD / command stboard

But anayway:

Quoted 8 lines
Quoted 5 lines

I propose something for the first point on the custodians git, branch "dh"
https://gitlab.denx.de/u-boot/custodians/u-boot-stm.git

see " fixup! ARM: dts: stm32: Add DH Electronics DHCOM SoM and PDK2 board" on dh branch

Did you verify that the generated DT is identical for U-Boot and SPL before and after this change ?

Yes => same dtb after the patch.

(I use "dtc -I dtb -O dts" on the generated files and I compare the dts file)

Quoted 9 lines
Quoted 7 lines

Are you are ok with this proposal ?

In the same branch I propose 2 other modifications to reduce the size of board.c (remove feature note needed).

- remove stusb1600 support
- remove OTP_BOARD support and cmd_stboard

These two are OK, thanks.

You send a V3 ?

I can squash the 3 commit on the branch And I merge it like that.... Regards

Quoted 4 lines

--
Best regards,
Marek Vasut

Patrick

#4 lore raw

PATCH v2 1/1 ARM: dts: stm32: Add DH Electronics DHCOM SoM and PDK2 board

Quoted 1 line · Patrick DELAUNAY

Hi Marek

Hi,

Quoted 35 lines
Quoted 35 lines

From: Marek Vasut <[email protected]>
Sent: jeudi 23 janvier 2020 23:45

Quoted 1 line · Patrick DELAUNAY

Hi Marek,

Hi,

Quoted 26 lines
Quoted 10 lines

From: Marek Vasut <[email protected]>
Sent: mardi 21 janvier 2020 22:39

Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier board. This is an SoM with STM32MP157C and an evaluation kit. The baseboard provides Ethernet, UART, USB, CAN and optional display.

Cc Patrick Delaunay <[email protected]>
Cc Patrice Chotard <[email protected]>

Few remarks (see after) about
1/ name of dts file (I prefer to don't add a file "-u-boot.dts") 2/ stusb1600 support (it seens that the PDK2 board hav no this USB type C controller, so part of code can be dropped) 3/ ST board specific part are not needed : OTP_BOARD / command stboard

But anayway:

I propose something for the first point on the custodians git, branch "dh"
https://gitlab.denx.de/u-boot/custodians/u-boot-stm.git

see " fixup! ARM: dts: stm32: Add DH Electronics DHCOM SoM and PDK2 board" on dh branch

Quoted 6 lines
Quoted 2 lines

Did you verify that the generated DT is identical for U-Boot and SPL before and after this change ?

Yes => same dtb after the patch.

(I use "dtc -I dtb -O dts" on the generated files and I compare the dts file)

OK, then that's good.

Quoted 8 lines
Quoted 8 lines
Quoted 7 lines

Are you are ok with this proposal ?

In the same branch I propose 2 other modifications to reduce the size of board.c (remove feature note needed).

- remove stusb1600 support
- remove OTP_BOARD support and cmd_stboard

Quoted 6 lines
Quoted 1 line

These two are OK, thanks.

You send a V3 ?

I can squash the 3 commit on the branch And I merge it like that.... Regards

I also renamed the DTs to indicate that you can insert any arbitrary stm32mp15xx SoC into the board.

Signature · 2 lines
Best regards,
Marek Vasut