Skip to contentSkip to conversation

Add support for SoM "VoCore2".

PATCH New Mauro Condarelli 3 participants 3 messages Feb 18, 2020 – Apr 27, 2020 MIPS

lore
Share & tools
lore
#0 lore raw

PATCH v6 1/1 Add support for SoM "VoCore2".

Small patch to add support for VoCore/VoCore2 board.

VoCore is open hardware and runs OpenWrt/LEDE.
It has WIFI, USB, UART, 20+ GPIOs but is only one inch square. It will help you to make a smart house, study embedded system or even make the tiniest router in the world.

Details about this SoM can be found at "https://vocore.io/v2.html".

---

Changes in v6:
- Added MAINTAINERS file.
- Removed project-specific configs/vocore2_defconfig_ENV_IN_FAT.
- Removed guard for SPL Serial definitions in include/configs/vocore2.h.
- Removed Baudrate Table definition in include/configs/vocore2.h.
- Moved board-specific DTS settingsto arch/mips/dts/vocore_vocore2.dts.
- Added UART2 pin definitions to arch/mips/dts/vocore_vocore2.dts.
- Removed unused mmc pin definition from arch/mips/dts/vocore_vocore2.dts.
- Added select of SPL_UART2_SPIS_PINMUX in board choice.
- Updated configs/vocore2_defconfig.

Changes in v5:
- Removed unneeded (and wrong) UART2 initialization in board.c
- Added network setup.
- Removed project-specific code.
- Move back environment to SPI NOR.
- Changes to environment default settings.
- Rebase on current u-boot-mips/testing.

Changes in v4:
- Reverted some overzealous DTS cleaning.
- Added support for bootcount.

Changes in v3:
- based on top of Weijie Gao patchset:
"[v3,xx/20]Refactor the architecture parts of mt7628"

Changes in v2:
- Removed some dead code
- Changed Author to my full name (no nick)
- Removed unwanted fixup to .dts generation (not my call).
- Fixed commit message
- Fixed various variables/filenames to include Vendor name
- Changed Vendor name (Vonger -> Vocore)

 arch/mips/dts/Makefile           |   1 +
 arch/mips/dts/vocore_vocore2.dts |  85 ++++++++++++++++++++++++++
 arch/mips/mach-mtmips/Kconfig    |  10 +++
 board/vocore/vocore2/Kconfig     |  12 ++++
 board/vocore/vocore2/MAINTAINERS |   7 +++
 board/vocore/vocore2/Makefile    |   3 +
 board/vocore/vocore2/board.c     |   6 ++
 configs/vocore2_defconfig        | 101 +++++++++++++++++++++++++++++++
 include/configs/vocore2.h        |  54 +++++++++++++++++
 9 files changed, 279 insertions(+)
 create mode 100644 arch/mips/dts/vocore_vocore2.dts
 create mode 100644 board/vocore/vocore2/Kconfig
 create mode 100644 board/vocore/vocore2/MAINTAINERS
 create mode 100644 board/vocore/vocore2/Makefile
 create mode 100644 board/vocore/vocore2/board.c
 create mode 100644 configs/vocore2_defconfig
 create mode 100644 include/configs/vocore2.h
arch/mips/dts/Makefile +1 -0
index cbd0c8bc8b..f711e9fb59 100644
@@ -23,6 +23,7 @@ dtb-$(CONFIG_BOARD_NETGEAR_DGND3700V2) += netgear,dgnd3700v2.dtb
 dtb-$(CONFIG_BOARD_SAGEM_FAST1704) += sagem,f at st1704.dtb
 dtb-$(CONFIG_BOARD_SFR_NB4_SER) += sfr,nb4-ser.dtb
 dtb-$(CONFIG_BOARD_TPLINK_WDR4300) += tplink_wdr4300.dtb
+dtb-$(CONFIG_BOARD_VOCORE2) += vocore_vocore2.dtb
 dtb-$(CONFIG_TARGET_JZ4780_CI20) += ci20.dtb
 dtb-$(CONFIG_SOC_LUTON) += luton_pcb090.dtb luton_pcb091.dtb
 dtb-$(CONFIG_SOC_OCELOT) += ocelot_pcb120.dtb ocelot_pcb123.dtb
arch/mips/dts/vocore_vocore2.dts new file +85 -0

85 lines not on this page · raw message

arch/mips/mach-mtmips/Kconfig +10 -0
index bcd635f438..6ca3b3aad3 100644
@@ -83,6 +83,15 @@ config BOARD_MT7628_RFB
 	  SPI-NOR flash, 1 built-in switch with 5 ports, 1 UART, 1 USB host,
 	  1 SDXC, 1 PCIe socket and JTAG pins.
 
+config BOARD_VOCORE2
+	bool "VoCore2"
+	depends on SOC_MT7628
+	select SPL_SERIAL_SUPPORT
+	select SPL_UART2_SPIS_PINMUX
+	help
+	  VoCore VoCore2 board has a MT7628 SoC with 128 MiB of RAM
+	  and 16 MiB of flash (SPI).
+
 endchoice
 
 config SPL_UART2_SPIS_PINMUX
@@ -96,5 +105,6 @@ config SPL_UART2_SPIS_PINMUX
 source "board/gardena/smart-gateway-mt7688/Kconfig"
 source "board/mediatek/mt7628/Kconfig"
 source "board/seeed/linkit-smart-7688/Kconfig"
+source "board/vocore/vocore2/Kconfig"
 
 endmenu
board/vocore/vocore2/Kconfig new file +12 -0
new file mode 100644
index 0000000000..baeff31b69
@@ -0,0 +1,12 @@
+if BOARD_VOCORE2
+
+config SYS_BOARD
+	default "vocore2"
+
+config SYS_VENDOR
+	default "vocore"
+
+config SYS_CONFIG_NAME
+	default "vocore2"
+
+endif
board/vocore/vocore2/MAINTAINERS new file +7 -0
new file mode 100644
index 0000000000..8472351fe2
@@ -0,0 +1,7 @@
+VOCORE_VOCORE2 BOARD
+M:	Mauro Condarelli <[email protected]>
+S:	Maintained
+F: board/vocore/vocore2
+F: include/configs/vocore2.h
+F: configs/vocore2_defconfig
+F: arch/mips/dts/vocore_vocore2.dts
board/vocore/vocore2/Makefile new file +3 -0
new file mode 100644
index 0000000000..70cd7a8e56
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0+
+
+obj-y += board.o
board/vocore/vocore2/board.c new file +6 -0
new file mode 100644
index 0000000000..27e42d1414
@@ -0,0 +1,6 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2019 Mauro Condarelli <[email protected]>
+ *
+ * Nothing actually needed here
+ */
configs/vocore2_defconfig new file +101 -0

101 lines not on this page · raw message

include/configs/vocore2.h new file +54 -0

54 lines not on this page · raw message

Signature · 1 line
2.25.0
#1 lore raw

PATCH v6 1/1 Add support for SoM "VoCore2".

Quoted 96 lines · Mauro Condarelli

Small patch to add support for VoCore/VoCore2 board.

VoCore is open hardware and runs OpenWrt/LEDE.
It has WIFI, USB, UART, 20+ GPIOs but is only one inch square. It will help you to make a smart house, study embedded system or even make the tiniest router in the world.

Details about this SoM can be found at "https://vocore.io/v2.html".

---

Changes in v6:
- Added MAINTAINERS file.
- Removed project-specific configs/vocore2_defconfig_ENV_IN_FAT.
- Removed guard for SPL Serial definitions in include/configs/vocore2.h.
- Removed Baudrate Table definition in include/configs/vocore2.h.
- Moved board-specific DTS settingsto arch/mips/dts/vocore_vocore2.dts.
- Added UART2 pin definitions to arch/mips/dts/vocore_vocore2.dts.
- Removed unused mmc pin definition from arch/mips/dts/vocore_vocore2.dts.
- Added select of SPL_UART2_SPIS_PINMUX in board choice.
- Updated configs/vocore2_defconfig.

Changes in v5:
- Removed unneeded (and wrong) UART2 initialization in board.c
- Added network setup.
- Removed project-specific code.
- Move back environment to SPI NOR.
- Changes to environment default settings.
- Rebase on current u-boot-mips/testing.

Changes in v4:
- Reverted some overzealous DTS cleaning.
- Added support for bootcount.

Changes in v3:
- based on top of Weijie Gao patchset:
"[v3,xx/20]Refactor the architecture parts of mt7628"

Changes in v2:
- Removed some dead code
- Changed Author to my full name (no nick)
- Removed unwanted fixup to .dts generation (not my call).
- Fixed commit message
- Fixed various variables/filenames to include Vendor name
- Changed Vendor name (Vonger -> Vocore)

  arch/mips/dts/Makefile           |   1 +
  arch/mips/dts/vocore_vocore2.dts |  85 ++++++++++++++++++++++++++
  arch/mips/mach-mtmips/Kconfig    |  10 +++
  board/vocore/vocore2/Kconfig     |  12 ++++
  board/vocore/vocore2/MAINTAINERS |   7 +++
  board/vocore/vocore2/Makefile    |   3 +
  board/vocore/vocore2/board.c     |   6 ++
  configs/vocore2_defconfig        | 101 +++++++++++++++++++++++++++++++
  include/configs/vocore2.h        |  54 +++++++++++++++++
  9 files changed, 279 insertions(+)

create mode 100644 arch/mips/dts/vocore_vocore2.dts create mode 100644 board/vocore/vocore2/Kconfig create mode 100644 board/vocore/vocore2/MAINTAINERS create mode 100644 board/vocore/vocore2/Makefile create mode 100644 board/vocore/vocore2/board.c create mode 100644 configs/vocore2_defconfig create mode 100644 include/configs/vocore2.h

arch/mips/dts/Makefile +1 -0
index cbd0c8bc8b..f711e9fb59 100644
@@ -23,6 +23,7 @@ dtb-$(CONFIG_BOARD_NETGEAR_DGND3700V2) += netgear,dgnd3700v2.dtb
  dtb-$(CONFIG_BOARD_SAGEM_FAST1704) += sagem,f at st1704.dtb
  dtb-$(CONFIG_BOARD_SFR_NB4_SER) += sfr,nb4-ser.dtb
  dtb-$(CONFIG_BOARD_TPLINK_WDR4300) += tplink_wdr4300.dtb
+dtb-$(CONFIG_BOARD_VOCORE2) += vocore_vocore2.dtb
  dtb-$(CONFIG_TARGET_JZ4780_CI20) += ci20.dtb
  dtb-$(CONFIG_SOC_LUTON) += luton_pcb090.dtb luton_pcb091.dtb
  dtb-$(CONFIG_SOC_OCELOT) += ocelot_pcb120.dtb ocelot_pcb123.dtb
arch/mips/dts/vocore_vocore2.dts new file +13 -0
new file mode 100644
index 0000000000..3502e4b8b7
@@ -0,0 +1,85 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2019 Mauro Condarelli <[email protected]>
+ */
+
+/dts-v1/;
+
+#include "mt7628a.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	compatible = "vocore,vocore2", "ralink,mt7628a-soc";
+	model = "VoCore2";

arch/mips/dts/vocore_vocore2.dts line 23

Quoted 10 lines
arch/mips/dts/vocore_vocore2.dts new file +10 -0
+
+	aliases {
+		serial0 = &uart2;
+		spi0 = &spi0;
+	};
+
+	memory at 0 {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};

Nitpicking: It looks nicer with an empty line here as well. But no need to send v7 because of this. Other than this:

Thanks,
Stefan

Quoted 299 lines
arch/mips/dts/vocore_vocore2.dts new file +62 -0
+	leds {
+		compatible = "gpio-leds";
+
+		power {
+			label = "vocore:power";
+			gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	chosen {
+		bootargs = "console=ttyS2,115200";
+		stdout-path = &uart2;
+	};
+};
+
+&pinctrl {
+	state_default: pin_state {
+		p0led {
+			groups = "p0led_a";
+			function = "led";
+		};
+	};
+};
+
+&uart2 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pwm_pins>;
+};
+
+&spi0 {
+	status = "okay";
+	nor0: spi-flash at 0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		spi-max-frequency = <25000000>;
+		reg = <0>;
+	};
+};
+
+&eth {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&ephy_iot_mode>;
+	mediatek,poll-link-phy = <0>;
+};
+
+&mmc {
+	status = "okay";
+
+	bus-width = <4>;
+	max-frequency = <48000000>;
+	cap-sd-highspeed;
+	cap-mmc-highspeed;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&sd_iot_mode>;
+};
arch/mips/mach-mtmips/Kconfig +10 -0
index bcd635f438..6ca3b3aad3 100644
@@ -83,6 +83,15 @@ config BOARD_MT7628_RFB
  	  SPI-NOR flash, 1 built-in switch with 5 ports, 1 UART, 1 USB host,
  	  1 SDXC, 1 PCIe socket and JTAG pins.
 
+config BOARD_VOCORE2
+	bool "VoCore2"
+	depends on SOC_MT7628
+	select SPL_SERIAL_SUPPORT
+	select SPL_UART2_SPIS_PINMUX
+	help
+	  VoCore VoCore2 board has a MT7628 SoC with 128 MiB of RAM
+	  and 16 MiB of flash (SPI).
+
  endchoice
 
  config SPL_UART2_SPIS_PINMUX
@@ -96,5 +105,6 @@ config SPL_UART2_SPIS_PINMUX
  source "board/gardena/smart-gateway-mt7688/Kconfig"
  source "board/mediatek/mt7628/Kconfig"
  source "board/seeed/linkit-smart-7688/Kconfig"
+source "board/vocore/vocore2/Kconfig"
 
  endmenu
board/vocore/vocore2/Kconfig new file +12 -0
new file mode 100644
index 0000000000..baeff31b69
@@ -0,0 +1,12 @@
+if BOARD_VOCORE2
+
+config SYS_BOARD
+	default "vocore2"
+
+config SYS_VENDOR
+	default "vocore"
+
+config SYS_CONFIG_NAME
+	default "vocore2"
+
+endif
board/vocore/vocore2/MAINTAINERS new file +7 -0
new file mode 100644
index 0000000000..8472351fe2
@@ -0,0 +1,7 @@
+VOCORE_VOCORE2 BOARD
+M:	Mauro Condarelli <[email protected]>
+S:	Maintained
+F: board/vocore/vocore2
+F: include/configs/vocore2.h
+F: configs/vocore2_defconfig
+F: arch/mips/dts/vocore_vocore2.dts
board/vocore/vocore2/Makefile new file +3 -0
new file mode 100644
index 0000000000..70cd7a8e56
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0+
+
+obj-y += board.o
board/vocore/vocore2/board.c new file +6 -0
new file mode 100644
index 0000000000..27e42d1414
@@ -0,0 +1,6 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2019 Mauro Condarelli <[email protected]>
+ *
+ * Nothing actually needed here
+ */
configs/vocore2_defconfig new file +101 -0
new file mode 100644
index 0000000000..952d9d42de
@@ -0,0 +1,101 @@
+CONFIG_MIPS=y
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_ENV_SIZE=0x1000
+CONFIG_ENV_SECT_SIZE=0x1000
+CONFIG_ENV_OFFSET=0x04e000
+CONFIG_SYS_BOOTCOUNT_ADDR=0xb000006c
+CONFIG_SPL_SYS_MALLOC_F_LEN=0x20000
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_SPL=y
+CONFIG_SYS_BOOTCOUNT_SINGLEWORD=y
+CONFIG_ARCH_MTMIPS=y
+CONFIG_BOARD_VOCORE2=y
+CONFIG_RESTORE_EXCEPTION_VECTOR_BASE=y
+CONFIG_MIPS_BOOT_FDT=y
+CONFIG_ENV_VARS_UBOOT_CONFIG=y
+CONFIG_SYS_BOOT_GET_CMDLINE=y
+CONFIG_SYS_BOOT_GET_KBD=y
+CONFIG_FIT=y
+CONFIG_FIT_SIGNATURE=y
+CONFIG_LEGACY_IMAGE_FORMAT=y
+CONFIG_OF_STDOUT_VIA_ALIAS=y
+CONFIG_LOGLEVEL=8
+CONFIG_VERSION_VARIABLE=y
+# CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_DISPLAY_BOARDINFO_LATE=y
+CONFIG_SPL_SYS_MALLOC_SIMPLE=y
+CONFIG_SPL_NOR_SUPPORT=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_LICENSE=y
+# CONFIG_BOOTM_NETBSD is not set
+# CONFIG_BOOTM_PLAN9 is not set
+# CONFIG_BOOTM_RTEMS is not set
+# CONFIG_BOOTM_VXWORKS is not set
+# CONFIG_CMD_ELF is not set
+# CONFIG_CMD_XIMG is not set
+# CONFIG_CMD_CRC32 is not set
+CONFIG_CMD_MEMINFO=y
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_GPT_RENAME=y
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_MTD=y
+CONFIG_CMD_PART=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_WDT=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_BOOTCOUNT=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_CMD_MTDPARTS=y
+CONFIG_MTDIDS_DEFAULT="nor0=spi0.0"
+CONFIG_MTDPARTS_DEFAULT="spi0.0:312k(u-boot),4k(env),4k(factory),2368k(kernel),-(filesystem)"
+CONFIG_DEFAULT_DEVICE_TREE="vocore_vocore2"
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_SPL_DM=y
+# CONFIG_DM_DEVICE_REMOVE is not set
+CONFIG_BOOTCOUNT_LIMIT=y
+CONFIG_LED=y
+CONFIG_LED_BLINK=y
+CONFIG_LED_GPIO=y
+CONFIG_MMC=y
+CONFIG_DM_MMC=y
+# CONFIG_MMC_HW_PARTITIONING is not set
+CONFIG_MMC_MTK=y
+CONFIG_MTD=y
+CONFIG_SPI_FLASH_SFDP_SUPPORT=y
+CONFIG_SPI_FLASH_GIGADEVICE=y
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_SPI_FLASH_WINBOND=y
+CONFIG_SPI_FLASH_MTD=y
+CONFIG_MT7628_ETH=y
+CONFIG_PHY=y
+CONFIG_MT76X8_USB_PHY=y
+# CONFIG_RAM_ROCKCHIP_DEBUG is not set
+CONFIG_SPECIFY_CONSOLE_INDEX=y
+CONFIG_CONS_INDEX=3
+CONFIG_SPI=y
+CONFIG_MT7621_SPI=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_GENERIC=y
+CONFIG_USB_STORAGE=y
+CONFIG_WDT=y
+CONFIG_WDT_MT7621=y
+CONFIG_FS_EXT4=y
+CONFIG_FAT_WRITE=y
+CONFIG_LZMA=y
+CONFIG_LZO=y
include/configs/vocore2.h new file +44 -0
new file mode 100644
index 0000000000..8100e4dca7
@@ -0,0 +1,54 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2019 Mauro Condarelli <[email protected]>
+ */
+
+#ifndef __VOCORE2_CONFIG_H__
+#define __VOCORE2_CONFIG_H__
+
+/* CPU */
+#define CONFIG_SYS_MIPS_TIMER_FREQ	290000000
+
+/* RAM */
+#define CONFIG_SYS_SDRAM_BASE		0x80000000
+
+#define CONFIG_SYS_LOAD_ADDR	CONFIG_SYS_SDRAM_BASE + 0x100000
+
+#define CONFIG_SYS_INIT_SP_OFFSET	0x400000
+
+/* SPL */
+#if defined(CONFIG_SPL) && !defined(CONFIG_SPL_BUILD)
+#define CONFIG_SKIP_LOWLEVEL_INIT
+#endif
+
+#define CONFIG_SYS_UBOOT_START		CONFIG_SYS_TEXT_BASE
+#define CONFIG_SPL_BSS_START_ADDR	0x80010000
+#define CONFIG_SPL_BSS_MAX_SIZE		0x10000
+#define CONFIG_SPL_MAX_SIZE		0x10000
+
+/* Dummy value */
+#define CONFIG_SYS_UBOOT_BASE		0
+
+/* Serial SPL */
+#define CONFIG_SYS_NS16550_MEM32
+#define CONFIG_SYS_NS16550_CLK		40000000
+#define CONFIG_SYS_NS16550_REG_SIZE	-4
+#define CONFIG_SYS_NS16550_COM3		0xb0000e00
+#define CONFIG_CONS_INDEX		3
+
+/* RAM */
+#define CONFIG_SYS_MEMTEST_START	0x80100000
+#define CONFIG_SYS_MEMTEST_END		0x80400000
+
+/* Memory usage */
+#define CONFIG_SYS_MAXARGS		64

include/configs/vocore2.h line 54

Quoted 10 lines
include/configs/vocore2.h new file +10 -0
+#define CONFIG_SYS_MALLOC_LEN		(1024 * 1024)
+#define CONFIG_SYS_BOOTPARAMS_LEN	(128 * 1024)
+#define CONFIG_SYS_CBSIZE		512
+
+/* U-Boot */
+#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_TEXT_BASE
+
+/* Environment settings */
+
+#endif //__VOCORE2_CONFIG_H__

Viele Gr??e,
Stefan

Signature · 3 lines
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: sr at denx.de
#2 lore raw

PATCH v6 1/1 Add support for SoM "VoCore2".

In reply to Mauro Condarelli

Am 18.02.20 um 09:34 schrieb Mauro Condarelli:

Quoted 56 lines

Small patch to add support for VoCore/VoCore2 board.

VoCore is open hardware and runs OpenWrt/LEDE.
It has WIFI, USB, UART, 20+ GPIOs but is only one inch square. It will help you to make a smart house, study embedded system or even make the tiniest router in the world.

Details about this SoM can be found at "https://vocore.io/v2.html".

---

Changes in v6:
- Added MAINTAINERS file.
- Removed project-specific configs/vocore2_defconfig_ENV_IN_FAT.
- Removed guard for SPL Serial definitions in include/configs/vocore2.h.
- Removed Baudrate Table definition in include/configs/vocore2.h.
- Moved board-specific DTS settingsto arch/mips/dts/vocore_vocore2.dts.
- Added UART2 pin definitions to arch/mips/dts/vocore_vocore2.dts.
- Removed unused mmc pin definition from arch/mips/dts/vocore_vocore2.dts.
- Added select of SPL_UART2_SPIS_PINMUX in board choice.
- Updated configs/vocore2_defconfig.

Changes in v5:
- Removed unneeded (and wrong) UART2 initialization in board.c
- Added network setup.
- Removed project-specific code.
- Move back environment to SPI NOR.
- Changes to environment default settings.
- Rebase on current u-boot-mips/testing.

Changes in v4:
- Reverted some overzealous DTS cleaning.
- Added support for bootcount.

Changes in v3:
- based on top of Weijie Gao patchset:
"[v3,xx/20]Refactor the architecture parts of mt7628"

Changes in v2:
- Removed some dead code
- Changed Author to my full name (no nick)
- Removed unwanted fixup to .dts generation (not my call).
- Fixed commit message
- Fixed various variables/filenames to include Vendor name
- Changed Vendor name (Vonger -> Vocore)

 arch/mips/dts/Makefile           |   1 +
 arch/mips/dts/vocore_vocore2.dts |  85 ++++++++++++++++++++++++++
 arch/mips/mach-mtmips/Kconfig    |  10 +++
 board/vocore/vocore2/Kconfig     |  12 ++++
 board/vocore/vocore2/MAINTAINERS |   7 +++
 board/vocore/vocore2/Makefile    |   3 +
 board/vocore/vocore2/board.c     |   6 ++
 configs/vocore2_defconfig        | 101 +++++++++++++++++++++++++++++++
 include/configs/vocore2.h        |  54 +++++++++++++++++
Quoted 9 lines
 9 files changed, 279 insertions(+)
 create mode 100644 arch/mips/dts/vocore_vocore2.dts
 create mode 100644 board/vocore/vocore2/Kconfig
 create mode 100644 board/vocore/vocore2/MAINTAINERS
 create mode 100644 board/vocore/vocore2/Makefile
 create mode 100644 board/vocore/vocore2/board.c
 create mode 100644 configs/vocore2_defconfig
 create mode 100644 include/configs/vocore2.h

applied to u-boot-mips/next with refreshing the defconfig

Signature · 1 line
- Daniel