ethtool: consolidate irq coalescing - part 5
Subsystems (15)
Jakub Kicinski
maintainerPATCH 1/15 net: jme: reject unsupported coalescing params
In reply to Jakub KicinskiSet ethtool_ops->supported_coalesce_params to let the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
--- drivers/net/ethernet/jme.c | 3 +++ 1 file changed, 3 insertions(+)
drivers/net/ethernet/jme.c +3 -0
@@ -2839,6 +2839,9 @@ jme_set_eeprom(struct net_device *netdev, }static const struct ethtool_ops jme_ethtool_ops = { + .supported_coalesce_params =ETHTOOL_COALESCE_USECS | +ETHTOOL_COALESCE_MAX_FRAMES | +ETHTOOL_COALESCE_USE_ADAPTIVE_RX , .get_drvinfo = jme_get_drvinfo, .get_regs_len = jme_get_regs_len, .get_regs = jme_get_regs,
Signature · 1 line
2.24.1
Jakub Kicinski
maintainerPATCH 2/15 net: mv643xx_eth: reject unsupported coalescing params
In reply to Jakub KicinskiSet ethtool_ops->supported_coalesce_params to let the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
--- drivers/net/ethernet/marvell/mv643xx_eth.c | 1 + 1 file changed, 1 insertion(+)
drivers/net/ethernet/marvell/mv643xx_eth.c +1 -0
@@ -1737,6 +1737,7 @@ static int mv643xx_eth_get_sset_count(struct net_device *dev, int sset) }static const struct ethtool_ops mv643xx_eth_ethtool_ops = { + .supported_coalesce_params =ETHTOOL_COALESCE_USECS , .get_drvinfo = mv643xx_eth_get_drvinfo, .nway_reset = phy_ethtool_nway_reset, .get_link = ethtool_op_get_link,
Signature · 1 line
2.24.1
Jakub Kicinski
maintainerPATCH 3/15 net: mvneta: reject unsupported coalescing params
In reply to Jakub KicinskiSet ethtool_ops->supported_coalesce_params to let the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
--- drivers/net/ethernet/marvell/mvneta.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/net/ethernet/marvell/mvneta.c +2 -0
@@ -4838,6 +4838,8 @@ static const struct net_device_ops mvneta_netdev_ops = { };static const struct ethtool_ops mvneta_eth_tool_ops = { + .supported_coalesce_params =ETHTOOL_COALESCE_RX_USECS | +ETHTOOL_COALESCE_MAX_FRAMES , .nway_reset = mvneta_ethtool_nway_reset, .get_link = ethtool_op_get_link, .set_coalesce = mvneta_ethtool_set_coalesce,
Signature · 1 line
2.24.1
Jakub Kicinski
maintainerPATCH 4/15 net: mvpp2: reject unsupported coalescing params
In reply to Jakub KicinskiSet ethtool_ops->supported_coalesce_params to let the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
--- drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c +2 -0
@@ -4384,6 +4384,8 @@ static const struct net_device_ops mvpp2_netdev_ops = { };static const struct ethtool_ops mvpp2_eth_tool_ops = { + .supported_coalesce_params =ETHTOOL_COALESCE_USECS | +ETHTOOL_COALESCE_MAX_FRAMES , .nway_reset = mvpp2_ethtool_nway_reset, .get_link = ethtool_op_get_link, .set_coalesce = mvpp2_ethtool_set_coalesce,
Signature · 1 line
2.24.1
Jakub Kicinski
maintainerPATCH 5/15 net: octeontx2-pf: let core reject the unsupported coalescing parameters
In reply to Jakub KicinskiSet ethtool_ops->supported_coalesce_params to let the core reject unsupported coalescing parameters.
This driver correctly rejects all unsupported
parameters, no functional changes.
--- .../ethernet/marvell/octeontx2/nic/otx2_ethtool.c | 13 ++----------- 1 file changed, 2 insertions(+), 11 deletions(-)
drivers/net/ethernet/marvell/octeontx2/nic/otx2_ethtool.c +2 -11
@@ -368,17 +368,6 @@ static int otx2_set_coalesce(struct net_device *netdev,struct otx2_hw *hw = &pfvf->hw;int qidx; -if (ec->use_adaptive_rx_coalesce || ec->use_adaptive_tx_coalesce || - ec->rx_coalesce_usecs_irq || ec->rx_max_coalesced_frames_irq || - ec->tx_coalesce_usecs_irq || ec->tx_max_coalesced_frames_irq || - ec->stats_block_coalesce_usecs || ec->pkt_rate_low || - ec->rx_coalesce_usecs_low || ec->rx_max_coalesced_frames_low || - ec->tx_coalesce_usecs_low || ec->tx_max_coalesced_frames_low || - ec->pkt_rate_high || ec->rx_coalesce_usecs_high || - ec->rx_max_coalesced_frames_high || ec->tx_coalesce_usecs_high || - ec->tx_max_coalesced_frames_high || ec->rate_sample_interval) -return -EOPNOTSUPP ; -if (!ec->rx_max_coalesced_frames || !ec->tx_max_coalesced_frames)return 0 ;
@@ -674,6 +663,8 @@ static u32 otx2_get_link(struct net_device *netdev) }static const struct ethtool_ops otx2_ethtool_ops = { + .supported_coalesce_params =ETHTOOL_COALESCE_USECS | +ETHTOOL_COALESCE_MAX_FRAMES , .get_link = otx2_get_link, .get_drvinfo = otx2_get_drvinfo, .get_strings = otx2_get_strings,
Signature · 1 line
2.24.1
Jakub Kicinski
maintainerPATCH 6/15 net: skge: reject unsupported coalescing params
In reply to Jakub KicinskiSet ethtool_ops->supported_coalesce_params to let the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
--- drivers/net/ethernet/marvell/skge.c | 1 + 1 file changed, 1 insertion(+)
drivers/net/ethernet/marvell/skge.c +1 -0
@@ -876,6 +876,7 @@ static int skge_set_eeprom(struct net_device *dev, struct ethtool_eeprom *eeprom }static const struct ethtool_ops skge_ethtool_ops = { + .supported_coalesce_params =ETHTOOL_COALESCE_USECS , .get_drvinfo = skge_get_drvinfo, .get_regs_len = skge_get_regs_len, .get_regs = skge_get_regs,
Signature · 1 line
2.24.1
Jakub Kicinski
maintainerPATCH 7/15 net: sky2: reject unsupported coalescing params
In reply to Jakub KicinskiSet ethtool_ops->supported_coalesce_params to let the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
--- drivers/net/ethernet/marvell/sky2.c | 4 ++++ 1 file changed, 4 insertions(+)
drivers/net/ethernet/marvell/sky2.c +4 -0
@@ -4400,6 +4400,10 @@ static int sky2_set_features(struct net_device *dev, netdev_features_t features) }static const struct ethtool_ops sky2_ethtool_ops = { + .supported_coalesce_params =ETHTOOL_COALESCE_USECS | +ETHTOOL_COALESCE_MAX_FRAMES | +ETHTOOL_COALESCE_RX_USECS_IRQ | +ETHTOOL_COALESCE_RX_MAX_FRAMES_IRQ , .get_drvinfo = sky2_get_drvinfo, .get_wol = sky2_get_wol, .set_wol = sky2_set_wol,
Signature · 1 line
2.24.1
Jakub Kicinski
maintainerPATCH 8/15 net: myri10ge: reject unsupported coalescing params
In reply to Jakub KicinskiSet ethtool_ops->supported_coalesce_params to let the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
--- drivers/net/ethernet/myricom/myri10ge/myri10ge.c | 1 + 1 file changed, 1 insertion(+)
drivers/net/ethernet/myricom/myri10ge/myri10ge.c +1 -0
@@ -1920,6 +1920,7 @@ myri10ge_phys_id(struct net_device *netdev, enum ethtool_phys_id_state state) }static const struct ethtool_ops myri10ge_ethtool_ops = { + .supported_coalesce_params =ETHTOOL_COALESCE_RX_USECS , .get_drvinfo = myri10ge_get_drvinfo, .get_coalesce = myri10ge_get_coalesce, .set_coalesce = myri10ge_set_coalesce,
Signature · 1 line
2.24.1
Jakub Kicinski
maintainerPATCH 9/15 net: nixge: let core reject the unsupported coalescing parameters
In reply to Jakub KicinskiSet ethtool_ops->supported_coalesce_params to let the core reject unsupported coalescing parameters.
This driver correctly rejects all unsupported
parameters, no functional changes.
--- drivers/net/ethernet/ni/nixge.c | 22 +--------------------- 1 file changed, 1 insertion(+), 21 deletions(-)
drivers/net/ethernet/ni/nixge.c +1 -21
@@ -1019,27 +1019,6 @@ static int nixge_ethtools_set_coalesce(struct net_device *ndev,return -EBUSY ; } -if (ecoalesce->rx_coalesce_usecs || - ecoalesce->rx_coalesce_usecs_irq || - ecoalesce->rx_max_coalesced_frames_irq || - ecoalesce->tx_coalesce_usecs || - ecoalesce->tx_coalesce_usecs_irq || - ecoalesce->tx_max_coalesced_frames_irq || - ecoalesce->stats_block_coalesce_usecs || - ecoalesce->use_adaptive_rx_coalesce || - ecoalesce->use_adaptive_tx_coalesce || - ecoalesce->pkt_rate_low || - ecoalesce->rx_coalesce_usecs_low || - ecoalesce->rx_max_coalesced_frames_low || - ecoalesce->tx_coalesce_usecs_low || - ecoalesce->tx_max_coalesced_frames_low || - ecoalesce->pkt_rate_high || - ecoalesce->rx_coalesce_usecs_high || - ecoalesce->rx_max_coalesced_frames_high || - ecoalesce->tx_coalesce_usecs_high || - ecoalesce->tx_max_coalesced_frames_high || - ecoalesce->rate_sample_interval) -return -EOPNOTSUPP ;if (ecoalesce->rx_max_coalesced_frames) priv->coalesce_count_rx = ecoalesce->rx_max_coalesced_frames;if (ecoalesce->tx_max_coalesced_frames)
@@ -1083,6 +1062,7 @@ static int nixge_ethtools_set_phys_id(struct net_device *ndev, }static const struct ethtool_ops nixge_ethtool_ops = { + .supported_coalesce_params =ETHTOOL_COALESCE_MAX_FRAMES , .get_drvinfo = nixge_ethtools_get_drvinfo, .get_coalesce = nixge_ethtools_get_coalesce, .set_coalesce = nixge_ethtools_set_coalesce,
Signature · 1 line
2.24.1
Jakub Kicinski
maintainerPATCH 10/15 net: netxen: let core reject the unsupported coalescing parameters
In reply to Jakub KicinskiSet ethtool_ops->supported_coalesce_params to let the core reject unsupported coalescing parameters.
As a side effect of these changes the error code for unsupported params changes from EINVAL to EOPNOTSUPP.
The driver was missing a check for rate_sample_interval.
--- .../qlogic/netxen/netxen_nic_ethtool.c | 21 +++---------------- 1 file changed, 3 insertions(+), 18 deletions(-)
drivers/net/ethernet/qlogic/netxen/netxen_nic_ethtool.c +3 -18
@@ -748,24 +748,7 @@ static int netxen_set_intr_coalesce(struct net_device *netdev,if (ethcoal->rx_coalesce_usecs >0xffff || ethcoal->rx_max_coalesced_frames >0xffff || ethcoal->tx_coalesce_usecs >0xffff || - ethcoal->tx_max_coalesced_frames >0xffff || - ethcoal->rx_coalesce_usecs_irq || - ethcoal->rx_max_coalesced_frames_irq || - ethcoal->tx_coalesce_usecs_irq || - ethcoal->tx_max_coalesced_frames_irq || - ethcoal->stats_block_coalesce_usecs || - ethcoal->use_adaptive_rx_coalesce || - ethcoal->use_adaptive_tx_coalesce || - ethcoal->pkt_rate_low || - ethcoal->rx_coalesce_usecs_low || - ethcoal->rx_max_coalesced_frames_low || - ethcoal->tx_coalesce_usecs_low || - ethcoal->tx_max_coalesced_frames_low || - ethcoal->pkt_rate_high || - ethcoal->rx_coalesce_usecs_high || - ethcoal->rx_max_coalesced_frames_high || - ethcoal->tx_coalesce_usecs_high || - ethcoal->tx_max_coalesced_frames_high) + ethcoal->tx_max_coalesced_frames >0xffff )return -EINVAL ; if (!ethcoal->rx_coalesce_usecs ||
@@ -923,6 +906,8 @@ netxen_get_dump_data(struct net_device *netdev, struct ethtool_dump *dump, }const struct ethtool_ops netxen_nic_ethtool_ops = { + .supported_coalesce_params =ETHTOOL_COALESCE_USECS | +ETHTOOL_COALESCE_MAX_FRAMES , .get_drvinfo = netxen_nic_get_drvinfo, .get_regs_len = netxen_nic_get_regs_len, .get_regs = netxen_nic_get_regs,
Signature · 1 line
2.24.1
Jakub Kicinski
maintainerPATCH 11/15 net: qede: reject unsupported coalescing params
In reply to Jakub KicinskiSet ethtool_ops->supported_coalesce_params to let the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
--- drivers/net/ethernet/qlogic/qede/qede_ethtool.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/net/ethernet/qlogic/qede/qede_ethtool.c +2 -0
@@ -2087,6 +2087,7 @@ static int qede_get_dump_data(struct net_device *dev, }static const struct ethtool_ops qede_ethtool_ops = { + .supported_coalesce_params =ETHTOOL_COALESCE_USECS , .get_link_ksettings = qede_get_link_ksettings, .set_link_ksettings = qede_set_link_ksettings, .get_drvinfo = qede_get_drvinfo,
@@ -2133,6 +2134,7 @@ static const struct ethtool_ops qede_ethtool_ops = { };static const struct ethtool_ops qede_vf_ethtool_ops = { + .supported_coalesce_params =ETHTOOL_COALESCE_USECS , .get_link_ksettings = qede_get_link_ksettings, .get_drvinfo = qede_get_drvinfo, .get_msglevel = qede_get_msglevel,
Signature · 1 line
2.24.1
Jakub Kicinski
maintainerPATCH 13/15 net: r8169: reject unsupported coalescing params
In reply to Jakub KicinskiSet ethtool_ops->supported_coalesce_params to let the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
--- drivers/net/ethernet/realtek/r8169_main.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/net/ethernet/realtek/r8169_main.c +2 -0
@@ -2006,6 +2006,8 @@ static int rtl8169_set_eee(struct net_device *dev, struct ethtool_eee *data) }static const struct ethtool_ops rtl8169_ethtool_ops = { + .supported_coalesce_params =ETHTOOL_COALESCE_USECS | +ETHTOOL_COALESCE_MAX_FRAMES , .get_drvinfo = rtl8169_get_drvinfo, .get_regs_len = rtl8169_get_regs_len, .get_link = ethtool_op_get_link,
Signature · 1 line
2.24.1
Jakub Kicinski
maintainerPATCH 14/15 net: sxgbe: reject unsupported coalescing params
In reply to Jakub KicinskiSet ethtool_ops->supported_coalesce_params to let the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
--- drivers/net/ethernet/samsung/sxgbe/sxgbe_ethtool.c | 1 + 1 file changed, 1 insertion(+)
drivers/net/ethernet/samsung/sxgbe/sxgbe_ethtool.c +1 -0
@@ -476,6 +476,7 @@ static int sxgbe_get_regs_len(struct net_device *dev) }static const struct ethtool_ops sxgbe_ethtool_ops = { + .supported_coalesce_params =ETHTOOL_COALESCE_RX_USECS , .get_drvinfo = sxgbe_getdrvinfo, .get_msglevel = sxgbe_getmsglevel, .set_msglevel = sxgbe_setmsglevel,
Signature · 1 line
2.24.1
Jakub Kicinski
maintainerPATCH 12/15 net: qlnic: let core reject the unsupported coalescing parameters
In reply to Jakub KicinskiSet ethtool_ops->supported_coalesce_params to let the core reject unsupported coalescing parameters.
This driver already correctly rejected almost all unsupported parameters (missing sample_rate_interval).
As a side effect of these changes the error code for unsupported params changes from EINVAL to EOPNOTSUPP.
--- .../ethernet/qlogic/qlcnic/qlcnic_ethtool.c | 23 ++++--------------- 1 file changed, 5 insertions(+), 18 deletions(-)
drivers/net/ethernet/qlogic/qlcnic/qlcnic_ethtool.c +5 -18
@@ -1542,24 +1542,7 @@ static int qlcnic_set_intr_coalesce(struct net_device *netdev,if (ethcoal->rx_coalesce_usecs >0xffff || ethcoal->rx_max_coalesced_frames >0xffff || ethcoal->tx_coalesce_usecs >0xffff || - ethcoal->tx_max_coalesced_frames >0xffff || - ethcoal->rx_coalesce_usecs_irq || - ethcoal->rx_max_coalesced_frames_irq || - ethcoal->tx_coalesce_usecs_irq || - ethcoal->tx_max_coalesced_frames_irq || - ethcoal->stats_block_coalesce_usecs || - ethcoal->use_adaptive_rx_coalesce || - ethcoal->use_adaptive_tx_coalesce || - ethcoal->pkt_rate_low || - ethcoal->rx_coalesce_usecs_low || - ethcoal->rx_max_coalesced_frames_low || - ethcoal->tx_coalesce_usecs_low || - ethcoal->tx_max_coalesced_frames_low || - ethcoal->pkt_rate_high || - ethcoal->rx_coalesce_usecs_high || - ethcoal->rx_max_coalesced_frames_high || - ethcoal->tx_coalesce_usecs_high || - ethcoal->tx_max_coalesced_frames_high) + ethcoal->tx_max_coalesced_frames >0xffff )return -EINVAL ; err =qlcnic_config_intr_coalesce (adapter, ethcoal);
@@ -1834,6 +1817,8 @@ qlcnic_set_dump(struct net_device *netdev, struct ethtool_dump *val) }const struct ethtool_ops qlcnic_ethtool_ops = { + .supported_coalesce_params =ETHTOOL_COALESCE_USECS | +ETHTOOL_COALESCE_MAX_FRAMES , .get_drvinfo = qlcnic_get_drvinfo, .get_regs_len = qlcnic_get_regs_len, .get_regs = qlcnic_get_regs,
@@ -1865,6 +1850,8 @@ const struct ethtool_ops qlcnic_ethtool_ops = { };const struct ethtool_ops qlcnic_sriov_vf_ethtool_ops = { + .supported_coalesce_params =ETHTOOL_COALESCE_USECS | +ETHTOOL_COALESCE_MAX_FRAMES , .get_drvinfo = qlcnic_get_drvinfo, .get_regs_len = qlcnic_get_regs_len, .get_regs = qlcnic_get_regs,
Signature · 1 line
2.24.1
Jakub Kicinski
maintainerPATCH 15/15 net: via: reject unsupported coalescing params
In reply to Jakub KicinskiSet ethtool_ops->supported_coalesce_params to let the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
--- drivers/net/ethernet/via/via-velocity.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/net/ethernet/via/via-velocity.c +2 -0
@@ -3648,6 +3648,8 @@ static void velocity_get_ethtool_stats(struct net_device *dev, }static const struct ethtool_ops velocity_ethtool_ops = { + .supported_coalesce_params =ETHTOOL_COALESCE_USECS | +ETHTOOL_COALESCE_MAX_FRAMES , .get_drvinfo = velocity_get_drvinfo, .get_wol = velocity_ethtool_get_wol, .set_wol = velocity_ethtool_set_wol,
Signature · 1 line
2.24.1
Jakub Kicinski
maintainercover ethtool: consolidate irq coalescing - part 5
Hi!
Convert more drivers following the groundwork laid in a recent patch set [1] and continued in [2], [3], [4]. The aim of the effort is to consolidate irq coalescing parameter validation in the core.
This set converts further 15 drivers in drivers/net/ethernet. One more conversion sets to come.
[1] https://lore.kernel.org/netdev/[email protected]/
[2] https://lore.kernel.org/netdev/[email protected]/
[3] https://lore.kernel.org/netdev/[email protected]/
[4] https://lore.kernel.org/netdev/[email protected]/
Jakub Kicinski (15):
net: jme: reject unsupported coalescing params
net: mv643xx_eth: reject unsupported coalescing params
net: mvneta: reject unsupported coalescing params
net: mvpp2: reject unsupported coalescing params
net: octeontx2-pf: let core reject the unsupported coalescing
parameters
net: skge: reject unsupported coalescing params
net: sky2: reject unsupported coalescing params
net: myri10ge: reject unsupported coalescing params
net: nixge: let core reject the unsupported coalescing parameters
net: netxen: let core reject the unsupported coalescing parameters
net: qede: reject unsupported coalescing params
net: qlnic: let core reject the unsupported coalescing parameters
net: r8169: reject unsupported coalescing params
net: sxgbe: reject unsupported coalescing params
net: via: reject unsupported coalescing params
drivers/net/ethernet/jme.c | 3 +++ drivers/net/ethernet/marvell/mv643xx_eth.c | 1 + drivers/net/ethernet/marvell/mvneta.c | 2 ++ .../net/ethernet/marvell/mvpp2/mvpp2_main.c | 2 ++ .../marvell/octeontx2/nic/otx2_ethtool.c | 13 ++--------- drivers/net/ethernet/marvell/skge.c | 1 + drivers/net/ethernet/marvell/sky2.c | 4 ++++ .../net/ethernet/myricom/myri10ge/myri10ge.c | 1 + drivers/net/ethernet/ni/nixge.c | 22 +----------------- .../qlogic/netxen/netxen_nic_ethtool.c | 21 +++-------------- .../net/ethernet/qlogic/qede/qede_ethtool.c | 2 ++ .../ethernet/qlogic/qlcnic/qlcnic_ethtool.c | 23 ++++--------------- drivers/net/ethernet/realtek/r8169_main.c | 2 ++ .../ethernet/samsung/sxgbe/sxgbe_ethtool.c | 1 + drivers/net/ethernet/via/via-velocity.c | 2 ++ 15 files changed, 32 insertions(+), 68 deletions(-)
Signature · 1 line
2.24.1
Re: [PATCH net-next 13/15] net: r8169: reject unsupported coalescing params
In reply to Jakub KicinskiQuoted 10 lines · Jakub Kicinski
Set
ethtool_ops->supported_coalesce_paramsto let the core reject unsupported coalescing parameters.This driver did not previously reject unsupported parameters.
Signed-off-by Jakub Kicinski <[email protected]>--- drivers/net/ethernet/realtek/r8169_main.c | 2 ++ 1 file changed, 2 insertions(+)
Re: [PATCH net-next 04/15] net: mvpp2: reject unsupported coalescing params
In reply to Jakub KicinskiQuoted 25 lines · Jakub Kicinski
Set
ethtool_ops->supported_coalesce_paramsto let the core reject unsupported coalescing parameters.This driver did not previously reject unsupported parameters.
Signed-off-by Jakub Kicinski <[email protected]>--- drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 2 ++ 1 file changed, 2 insertions(+)drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c +2
-1@@ -4384,6 +4384,8 @@ static const struct net_device_ops mvpp2_netdev_ops = { };static const struct ethtool_ops mvpp2_eth_tool_ops = { + .supported_coalesce_params =ETHTOOL_COALESCE_USECS | +ETHTOOL_COALESCE_MAX_FRAMES , .nway_reset = mvpp2_ethtool_nway_reset, .get_link = ethtool_op_get_link, .set_coalesce = mvpp2_ethtool_set_coalesce, --
Quoted 2 lines
2.24.1
Signature · 2 lines
Matteo Croce per aspera ad upstream
David Miller
maintainerFrom: Jakub Kicinski <[email protected]>
Date: Thu, 12 Mar 2020 21:07:48 -0700
Quoted 11 lines
Convert more drivers following the groundwork laid in a recent patch set [1] and continued in [2], [3], [4]. The aim of the effort is to consolidate irq coalescing parameter validation in the core.
This set converts further 15 drivers in
drivers/net/ethernet. One more conversion sets to come.[1] https://lore.kernel.org/netdev/[email protected]/
[2] https://lore.kernel.org/netdev/[email protected]/
[3] https://lore.kernel.org/netdev/[email protected]/
[4] https://lore.kernel.org/netdev/[email protected]/
Series applied, thanks Jakub.