i2c: designware: Fix spelling typos in the comments
Subsystems (3)
Andy Shevchenko
reviewerPATCH 1/1 i2c: designware: Fix spelling typos in the comments
Fix spelling typos in the comments with help of codespell.
Signed-off-by Andy Shevchenko <[email protected]>
--- drivers/i2c/busses/i2c-designware-baytrail.c | 2 +- drivers/i2c/busses/i2c-designware-common.c | 8 ++++---- drivers/i2c/busses/i2c-designware-master.c | 2 +- drivers/i2c/busses/i2c-designware-pcidrv.c | 2 +- drivers/i2c/busses/i2c-designware-slave.c | 2 +- 5 files changed, 8 insertions(+), 8 deletions(-)
drivers/i2c/busses/i2c-designware-baytrail.c +1 -1
@@ -1,6 +1,6 @@// SPDX-License-Identifier: GPL-2.0 /* -* Intel BayTrail PMIC I2C bus semaphore implementaion +* Intel BayTrail PMIC I2C bus semaphore implementation * Copyright (c) 2014, Intel Corporation. */ #include <linux/device.h>
drivers/i2c/busses/i2c-designware-common.c +4 -4
@@ -102,7 +102,7 @@ int i2c_dw_set_reg_access(struct dw_i2c_dev *dev)i2c_dw_release_lock (dev);if (reg ==swab32 (DW_IC_COMP_TYPE_VALUE )) { -/* Configure register endianess access */ +/* Configure register endianness access */ dev->flags |=ACCESS_SWAP ; }else if (reg == (DW_IC_COMP_TYPE_VALUE &0x0000ffff )) {/* Configure register access mode 16bit */
@@ -190,10 +190,10 @@ int i2c_dw_set_sda_hold(struct dw_i2c_dev *dev)/* * Workaround for avoiding TX arbitration lost in case I2C -* slave pulls SDA down "too quickly" after falling egde of +* slave pulls SDA down "too quickly" after falling edge of * SCL by enabling non-zero SDA RX hold. Specification says it * extends incoming SDA low to high transition while SCL is -* high but it apprears to help also above issue. +* high but it appears to help also above issue. */ if (!(dev->sda_hold_time &DW_IC_SDA_HOLD_RX_MASK )) dev->sda_hold_time |=1 <<DW_IC_SDA_HOLD_RX_SHIFT ;
@@ -356,7 +356,7 @@ void i2c_dw_disable(struct dw_i2c_dev *dev)/* Disable controller */ __i2c_dw_disable (dev); -/* Disable all interupts */ +/* Disable all interrupts */ dw_writel (dev,0 ,DW_IC_INTR_MASK );dw_readl (dev,DW_IC_CLR_INTR ); }
drivers/i2c/busses/i2c-designware-master.c +1 -1
@@ -521,7 +521,7 @@ static u32 i2c_dw_read_clear_intrbits(struct dw_i2c_dev *dev)/* * The IC_INTR_STAT register just indicates "enabled" interrupts. -* Ths unmasked raw version of interrupt status bits are available +* The unmasked raw version of interrupt status bits is available * in the IC_RAW_INTR_STAT register. * * That is,
drivers/i2c/busses/i2c-designware-pcidrv.c +1 -1
@@ -110,7 +110,7 @@ static int mfld_setup(struct pci_dev *pdev, struct dw_pci_controller *c)static int mrfld_setup (struct pci_dev *pdev,struct dw_pci_controller *c) {/* -* On Intel Merrifield the user visible i2c busses are enumerated +* On Intel Merrifield the user visible i2c buses are enumerated * [1..7]. So, we add 1 to shift the default range. Besides that the * first PCI slot provides 4 functions, that's why we have to add 0 to * the first slot and 4 to the next one.
drivers/i2c/busses/i2c-designware-slave.c +1 -1
@@ -107,7 +107,7 @@ static u32 i2c_dw_read_clear_intrbits_slave(struct dw_i2c_dev *dev)/* * The IC_INTR_STAT register just indicates "enabled" interrupts. -* Ths unmasked raw version of interrupt status bits are available +* The unmasked raw version of interrupt status bits is available * in the IC_RAW_INTR_STAT register. * * That is,
Signature · 1 line
2.25.1
Quoted 11 lines · Andy Shevchenko
Fix spelling typos in the comments with help of
codespell.Signed-off-by Andy Shevchenko <[email protected]>--- drivers/i2c/busses/i2c-designware-baytrail.c | 2 +- drivers/i2c/busses/i2c-designware-common.c | 8 ++++---- drivers/i2c/busses/i2c-designware-master.c | 2 +- drivers/i2c/busses/i2c-designware-pcidrv.c | 2 +- drivers/i2c/busses/i2c-designware-slave.c | 2 +- 5 files changed, 8 insertions(+), 8 deletions(-)
Acked-by Jarkko Nikula <[email protected]>
Wolfram Sang
AppliedQuoted 3 lines · Andy Shevchenko
Fix spelling typos in the comments with help of
codespell.Signed-off-by Andy Shevchenko <[email protected]>
Applied to for-next, thanks!