Bugfix, simplification and cleanup in DSA tag_8021q
Subsystems (3)
Vladimir Oltean
maintainercover Bugfix, simplification and cleanup in DSA tag_8021q
From: Vladimir Oltean <[email protected]>
This series removes the dsa_8021q_remove_header and dsa_8021q_xmit functions and replaces them with saner implementations, thereby redefining what the tag_8021q module has to offer (at the moment, just the VLAN definitions and install/uninstall rules remain).
Vladimir Oltean (3):
net: dsa: tag_8021q: replace dsa_8021q_remove_header with
__skb_vlan_pop
net: dsa: tag_8021q: remove obsolete comment
net: dsa: tag_8021q: get rid of dsa_8021q_xmit
include/linux/dsa/8021q.h | 16 ----------- net/dsa/tag_8021q.c | 57 +-------------------------------------- net/dsa/tag_sja1105.c | 27 ++++++++++--------- 3 files changed, 16 insertions(+), 84 deletions(-)
Signature · 1 line
2.17.1
Vladimir Oltean
maintainerPATCH 1/3 net: dsa: tag_8021q: replace dsa_8021q_remove_header with __skb_vlan_pop
From: Vladimir Oltean <[email protected]>
Not only did this wheel did not need reinventing, but there is also an issue with it: It doesn't remove the VLAN header in a way that preserves the L2 payload checksum when that is being provided by the DSA master hw. It should recalculate checksum both for the push, before removing the header, and for the pull afterwards. But the current implementation is quite dizzying, with pulls followed immediately afterwards by pushes, the memmove is done before the push, etc. This makes a DSA master with RX checksumming offload to print stack traces with the infamous 'hw csum failure' message.
So remove the dsa_8021q_remove_header function and replace it with something that actually works with inet checksumming.
--- include/linux/dsa/8021q.h | 7 ------- net/dsa/tag_8021q.c | 43 --------------------------------------- net/dsa/tag_sja1105.c | 19 ++++++++--------- 3 files changed, 9 insertions(+), 60 deletions(-)
include/linux/dsa/8021q.h +0 -7
@@ -28,8 +28,6 @@ int dsa_8021q_rx_switch_id(u16 vid);int dsa_8021q_rx_source_port (u16 vid); -struct sk_buff *dsa_8021q_remove_header (struct sk_buff *skb); -#else int dsa_port_setup_8021q_tagging(struct dsa_switch *ds, int index,
@@ -64,11 +62,6 @@ int dsa_8021q_rx_source_port(u16 vid)return 0 ; } -struct sk_buff *dsa_8021q_remove_header (struct sk_buff *skb) -{ -return NULL ; -} -#endif /* IS_ENABLED(CONFIG_NET_DSA_TAG_8021Q) */ #endif /* _NET_DSA_8021Q_H */
net/dsa/tag_8021q.c +0 -43
47 lines not on this page · raw message
net/dsa/tag_sja1105.c +9 -10
@@ -250,14 +250,14 @@ static struct sk_buff *sja1105_rcv(struct sk_buff *skb, {struct sja1105_meta meta = {0 };int source_port, switch_id; -struct vlan_ethhdr *hdr; +struct ethhdr *hdr;u16 tpid, vid, tci;bool is_link_local;bool is_tagged;bool is_meta; - hdr =vlan_eth_hdr (skb); - tpid =ntohs (hdr->h_vlan_proto); + hdr =eth_hdr (skb); + tpid =ntohs (hdr->h_proto); is_tagged = (tpid ==ETH_P_SJA1105 ); is_link_local =sja1105_is_link_local (skb); is_meta =sja1105_is_meta_frame (skb);
@@ -266,7 +266,12 @@ static struct sk_buff *sja1105_rcv(struct sk_buff *skb,if (is_tagged) {/* Normal traffic path. */ - tci =ntohs (hdr->h_vlan_TCI); +skb_push_rcsum (skb,ETH_HLEN ); +__skb_vlan_pop (skb, &tci); +skb_pull_rcsum (skb,ETH_HLEN ); +skb_reset_network_header (skb); +skb_reset_transport_header (skb); + vid = tci &VLAN_VID_MASK ; source_port =dsa_8021q_rx_source_port (vid); switch_id =dsa_8021q_rx_switch_id (vid);
@@ -295,12 +300,6 @@ static struct sk_buff *sja1105_rcv(struct sk_buff *skb,return NULL ; } -/* Delete/overwrite fake VLAN header, DSA expects to not find -* it there, see dsa_switch_rcv: skb_push(skb, ETH_HLEN). -*/ -if (is_tagged) - skb =dsa_8021q_remove_header (skb); -return sja1105_rcv_meta_state_machine (skb, &meta, is_link_local, is_meta); }
Signature · 1 line
2.17.1
Vladimir Oltean
maintainerPATCH 3/3 net: dsa: tag_8021q: get rid of dsa_8021q_xmit
In reply to Vladimir OlteanFrom: Vladimir Oltean <[email protected]>
Calling vlan_insert_tag is easy enough that having a dedicated function in tag_8021q does not bring any benefit at all.
--- include/linux/dsa/8021q.h | 9 --------- net/dsa/tag_8021q.c | 10 ---------- net/dsa/tag_sja1105.c | 8 ++++++-- 3 files changed, 6 insertions(+), 21 deletions(-)
include/linux/dsa/8021q.h +0 -9
@@ -17,9 +17,6 @@ struct packet_type;int dsa_port_setup_8021q_tagging (struct dsa_switch *ds,int index,bool enabled); -struct sk_buff *dsa_8021q_xmit (struct sk_buff *skb,struct net_device *netdev, -u16 tpid,u16 tci); -u16 dsa_8021q_tx_vid (struct dsa_switch *ds,int port);u16 dsa_8021q_rx_vid (struct dsa_switch *ds,int port);
@@ -36,12 +33,6 @@ int dsa_port_setup_8021q_tagging(struct dsa_switch *ds, int index,return 0 ; } -struct sk_buff *dsa_8021q_xmit (struct sk_buff *skb,struct net_device *netdev, -u16 tpid,u16 tci) -{ -return NULL ; -} -u16 dsa_8021q_tx_vid (struct dsa_switch *ds,int port) {return 0 ;
net/dsa/tag_8021q.c +0 -10
@@ -286,14 +286,4 @@ int dsa_port_setup_8021q_tagging(struct dsa_switch *ds, int port, bool enabled) }EXPORT_SYMBOL_GPL (dsa_port_setup_8021q_tagging); -struct sk_buff *dsa_8021q_xmit (struct sk_buff *skb,struct net_device *netdev, -u16 tpid,u16 tci) -{ -/* skb->data points at skb_mac_header, which -* is fine for vlan_insert_tag. -*/ -return vlan_insert_tag (skb,htons (tpid), tci); -} -EXPORT_SYMBOL_GPL (dsa_8021q_xmit); -MODULE_LICENSE ("GPL v2" );
net/dsa/tag_sja1105.c +6 -2
@@ -103,6 +103,8 @@ static struct sk_buff *sja1105_xmit(struct sk_buff *skb,u16 tx_vid =dsa_8021q_tx_vid (dp->ds, dp->index);u16 queue_mapping =skb_get_queue_mapping (skb);u8 pcp =netdev_txq_to_tc (netdev, queue_mapping); +u16 tci = (pcp <<VLAN_PRIO_SHIFT ) | tx_vid; +u16 tpid =ETH_P_SJA1105 ;/* Transmitting management traffic does not rely upon switch tagging, * but instead SPI-installed management routes. Part 2 of this
@@ -119,8 +121,10 @@ static struct sk_buff *sja1105_xmit(struct sk_buff *skb,if (dsa_port_is_vlan_filtering (dp))return skb; -return dsa_8021q_xmit (skb, netdev,ETH_P_SJA1105 , - ((pcp <<VLAN_PRIO_SHIFT ) | tx_vid)); +/* skb->data points at skb_mac_header, which +* is fine for vlan_insert_tag. +*/ +return vlan_insert_tag (skb,htons (tpid), tci); } static void sja1105_transfer_meta(struct sk_buff *skb,
Signature · 1 line
2.17.1
Vladimir Oltean
maintainerPATCH 2/3 net: dsa: tag_8021q: remove obsolete comment
In reply to Vladimir OlteanFrom: Vladimir Oltean <[email protected]>
Since the commit mentioned below, the dsa_8021q_netdev_ops structure has been removed, so the comment is no longer true. Remove it.
--- net/dsa/tag_8021q.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-)
net/dsa/tag_8021q.c +1 -3
@@ -2,9 +2,7 @@/* Copyright (c) 2019, Vladimir Oltean <[email protected]> * * This module is not a complete tagger implementation. It only provides -* primitives for taggers that rely on 802.1Q VLAN tags to use. The -* dsa_8021q_netdev_ops is registered for API compliance and not used -* directly by callers. +* primitives for taggers that rely on 802.1Q VLAN tags to use. */ #include <linux/if_bridge.h> #include <linux/if_vlan.h>
Signature · 1 line
2.17.1
David Miller
maintainerFrom: Vladimir Oltean <[email protected]>
Date: Fri, 20 Mar 2020 02:00:48 +0200
Quoted 6 lines
From: Vladimir Oltean <[email protected]>
This series removes the
dsa_8021q_remove_headeranddsa_8021q_xmitfunctions and replaces them with saner implementations, thereby redefining what thetag_8021qmodule has to offer (at the moment, just the VLAN definitions and install/uninstall rules remain).
Two of the three things you list in your Subject line are not appropriate for "net", that being simplifications and cleanups.
Bug fixes for 'net' are fine, the rest go to 'net-next'.