USB: serial: option: add support for ASKEY WWHC050

PATCH Superseded Pawel Dembicki 2 participants 4 messages Mar 20, 2020 – Mar 24, 2020

Subsystems (2)

USB USB serial

lore

Share & tools

lore

Pawel Dembicki

author

2020-03-20 22:02 UTC #0 lore raw

PATCH 1/3 USB: serial: option: add support for ASKEY WWHC050

ASKEY WWHC050 is a mcie LTE modem.
The oem configuration states:

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1690 ProdID=7588 Rev=ff.ff
S:  Manufacturer=Android
S:  Product=Android
S:  SerialNumber=813f0eef6e6e
C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=84(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=86(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E:  Ad=88(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E:  Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=125us

Tested on openwrt distribution.

Signed-off-by Cezary Jackiewicz <[email protected]>

Signed-off-by Pawel Dembicki <[email protected]>

---
 drivers/usb/serial/option.c | 2 ++
 1 file changed, 2 insertions(+)

drivers/usb/serial/option.c +2 -0

index 0b5dcf973d94..2f17019d3810 100644
@@ -2018,6 +2018,8 @@ static const struct usb_device_id option_ids[] = {
 	  .driver_info = RSVD(4) | RSVD(5) },
 	{ USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x0105, 0xff),			/* Fibocom NL678 series */
 	  .driver_info = RSVD(6) },
+	{ USB_DEVICE_INTERFACE_CLASS(0x1690, 0x7588, 0xff),			/* ASKEY WWHC050 */
+	  .driver_info = RSVD(1) | RSVD(4) },
 	{ } /* Terminating entry */
 };
 MODULE_DEVICE_TABLE(usb, option_ids);

Signature · 1 line

2.20.1

Pawel Dembicki

author

2020-03-20 22:02 UTC #1 lore raw

PATCH 2/3 USB: serial: option: add BroadMobi BM806U

BroadMobi BM806U is an Qualcomm MDM9225 based 3G/4G modem. Tested hardware BM806U is mounted on D-Link DWR-921-C3 router.

T:  Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  2 Spd=480  MxCh= 0
D:  Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=2020 ProdID=2033 Rev= 2.28
S:  Manufacturer=Mobile Connect
S:  Product=Mobile Connect
S:  SerialNumber=f842866cfd5a
C:* #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=87(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E:  Ad=89(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

Signed-off-by Cezary Jackiewicz <[email protected]>

Signed-off-by Pawel Dembicki <[email protected]>

---
 drivers/usb/serial/option.c | 2 ++
 1 file changed, 2 insertions(+)

drivers/usb/serial/option.c +2 -0

index 2f17019d3810..49313a55e1f3 100644
@@ -1994,6 +1994,8 @@ static const struct usb_device_id option_ids[] = {
 	{ USB_DEVICE_AND_INTERFACE_INFO(0x07d1, 0x7e11, 0xff, 0xff, 0xff) },	/* D-Link DWM-156/A3 */
 	{ USB_DEVICE_INTERFACE_CLASS(0x2020, 0x2031, 0xff),			/* Olicard 600 */
 	  .driver_info = RSVD(4) },
+	{ USB_DEVICE_INTERFACE_CLASS(0x2020, 0x2033, 0xff),			/* BroadMobi BM806U */
+	  .driver_info = RSVD(4) },
 	{ USB_DEVICE_INTERFACE_CLASS(0x2020, 0x2060, 0xff),			/* BroadMobi BM818 */
 	  .driver_info = RSVD(4) },
 	{ USB_DEVICE_INTERFACE_CLASS(0x2020, 0x4000, 0xff) },			/* OLICARD300 - MT6225 */

Signature · 1 line

2.20.1

Pawel Dembicki

author

2020-03-20 22:02 UTC #2 lore raw

PATCH 3/3 USB: serial: option: add Wistron Neweb D19Q1

In reply to Pawel Dembicki

This modem is embedded on dlink dwr-960 router.
The oem configuration states:

T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1435 ProdID=d191 Rev=ff.ff
S: Manufacturer=Android
S: Product=Android
S: SerialNumber=0123456789ABCDEF
C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=88(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=125us

Tested on openwrt distribution

Signed-off-by Pawel Dembicki <[email protected]>

---
 drivers/usb/serial/option.c | 2 ++
 1 file changed, 2 insertions(+)

drivers/usb/serial/option.c +2 -0

index 49313a55e1f3..abc717b99204 100644
@@ -2022,6 +2022,8 @@ static const struct usb_device_id option_ids[] = {
 	  .driver_info = RSVD(6) },
 	{ USB_DEVICE_INTERFACE_CLASS(0x1690, 0x7588, 0xff),			/* ASKEY WWHC050 */
 	  .driver_info = RSVD(1) | RSVD(4) },
+	{ USB_DEVICE_INTERFACE_CLASS(0x1435, 0xd191, 0xff),			/* Wistron Neweb D19Q1 */
+	  .driver_info = RSVD(1) | RSVD(4) },
 	{ } /* Terminating entry */
 };
 MODULE_DEVICE_TABLE(usb, option_ids);

Signature · 1 line

2.20.1

Johan Hovold

maintainer

2020-03-24 09:22 UTC #3 lore raw

In reply to Pawel Dembicki

Quoted 32 lines · Pawel Dembicki

ASKEY WWHC050 is a mcie LTE modem.
The oem configuration states:

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1690 ProdID=7588 Rev=ff.ff
S:  Manufacturer=Android
S:  Product=Android
S:  SerialNumber=813f0eef6e6e
C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=84(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=86(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E:  Ad=88(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E:  Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=125us

Quoted 4 lines

Tested on openwrt distribution.
Signed-off-by Cezary Jackiewicz <[email protected]>
Signed-off-by Pawel Dembicki <[email protected]>

Thanks for the patches, looks good.

But who is really the author of patches 1 and 2? You or Cezary? In the first case, you can use the Co-Developed-By tag to give Cezary credit, and otherwise you need to add a From line so that authorship is recorded correctly.

Take a look at Documentation/process/submitting-patches.rst.

Quoted 9 lines

---
 drivers/usb/serial/option.c | 2 ++
 1 file changed, 2 insertions(+)

drivers/usb/serial/option.c +0 -0

index 0b5dcf973d94..2f17019d3810 100644

drivers/usb/serial/option.c static const struct usb_device_id option_ids[] = { · line 2022

Quoted 5 lines

drivers/usb/serial/option.c +2 -0

@@ -2018,6 +2018,8 @@ static const struct usb_device_id option_ids[] = {
 	  .driver_info = RSVD(4) | RSVD(5) },
 	{ USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x0105, 0xff),			/* Fibocom NL678 series */
 	  .driver_info = RSVD(6) },
+	{ USB_DEVICE_INTERFACE_CLASS(0x1690, 0x7588, 0xff),			/* ASKEY WWHC050 */
+	  .driver_info = RSVD(1) | RSVD(4) },

I know the entries here appear to be in mostly random order, but if you're adding numerical ids towards the end, perhaps you can try to insert them in order.

drivers/usb/serial/option.c static const struct usb_device_id option_ids[] = { · line 2025

Quoted 3 lines

drivers/usb/serial/option.c +0 -0

 	{ } /* Terminating entry */
 };
 MODULE_DEVICE_TABLE(usb, option_ids);

Johan