i.MXRT1050 add LCDIF support
Subsystems (6)
v2 cover i.MXRT1050 add LCDIF support
This patchset add support for LCDIF on i.MXRT1050 evk. This requires PLL5 to be setup, mxsfb needs to use display_timing to retrieve if Lcd has inverted PIXCLOCK from dts.
With this patchset applied we temporary loose DCache support until it will get implemented, since a function in mxsfb.c is needed for setting cache behaviour. Anyway this way Lcd will show the console same way as serial does.
Also I've moved private sunxi_ctfb_mode_to_display_timing() to videomodes since I need it for mxfsb.c too, then having a unified function to convert from ctfb_mode to display_timing.
Changes:V1->V2:
* moved hard-coded LCDIF's parent clock from clk-imxrt1050.c to imxrt1050-evk.dts
* reworded some commit log
Giulio Benetti (19):
clk: imx: pllv3: add enable_bit
clk: imx: clk-imxrt1050: fix typo in clock name "video:"
clk: imx: clk-imxrt1050: setup PLL5 for video in non-SPL
clk: imx: clk-imxrt1050: add set_parent() callback
videomodes: add helper function to convert from ctfb to display_timing
sunxi: display: use common video_ctfb_mode_to_display_timing()
video: mxsfb: add support for DM CLK
video: mxsfb: add support for i.MXRT
video: mxsfb: refactor for using display_timings
video: mxsfb: enable setting HSYNC negative polarity
video: mxsfb: enable setting VSYNC negative polarity
video: mxsfb: enable setting PIXDATA on negative edge
video: mxsfb: enable setting ENABLE negative polarity
imxrt1050_evk: add 16bpp video support if video layer enabled
ARM: dts: i.mxrt1050: add lcdif node
ARM: dts: imxrt1050: allow this dtsi file to be compiled in Linux
arch: arm: dts: imxrt1050-evk: add lcdif node
configs: imxrt1050-evk: enable video support/console
configs: imxrt1050-evk: temporary disable DCACHE
arch/arm/dts/imxrt1050-evk.dts | 60 ++++++++++++++ arch/arm/dts/imxrt1050.dtsi | 14 +++- arch/arm/include/asm/arch-imxrt/imx-regs.h | 6 ++ arch/arm/include/asm/mach-imx/regs-lcdif.h | 6 +- configs/imxrt1050-evk_defconfig | 6 ++ drivers/clk/imx/clk-imxrt1050.c | 30 ++++++- drivers/clk/imx/clk-pllv3.c | 9 +++ drivers/video/mxsfb.c | 94 ++++++++++++++-------- drivers/video/sunxi/sunxi_display.c | 33 +------- drivers/video/videomodes.c | 29 +++++++ drivers/video/videomodes.h | 3 + include/configs/imxrt1050-evk.h | 15 ++++ 12 files changed, 234 insertions(+), 71 deletions(-)
Signature · 1 line
2.20.1
PATCH v2 1/19 clk: imx: pllv3: add enable_bit
pllv3 PLLs have powerdown/up bits but enable bits too. Specifically "enable bit" enable the pll output, so when dis/enabling pll by setting/clearing power_bit we must also set/clear enable_bit.
--- drivers/clk/imx/clk-pllv3.c | 9 +++++++++ 1 file changed, 9 insertions(+)
drivers/clk/imx/clk-pllv3.c +9 -0
@@ -25,6 +25,7 @@#define PLL_DENOM_OFFSET 0x20#define BM_PLL_POWER (0x1 << 12) +#define BM_PLL_ENABLE (0x1 << 13)#define BM_PLL_LOCK (0x1 << 31)struct clk_pllv3 {
@@ -32,6 +33,7 @@ struct clk_pllv3 {void __iomem *base;u32 power_bit;bool powerup_set; +u32 enable_bit;u32 div_mask;u32 div_shift; };
@@ -83,6 +85,9 @@ static int clk_pllv3_generic_enable(struct clk *clk) val |= pll->power_bit; else val &= ~pll->power_bit; + + val |= pll->enable_bit; +writel (val, pll->base);return 0 ;
@@ -98,6 +103,9 @@ static int clk_pllv3_generic_disable(struct clk *clk) val &= ~pll->power_bit; else val |= pll->power_bit; + + val &= ~pll->enable_bit; +writel (val, pll->base);return 0 ;
@@ -238,6 +246,7 @@ struct clk *imx_clk_pllv3(enum imx_pllv3_type type, const char *name,return ERR_PTR (-ENOMEM ); pll->power_bit =BM_PLL_POWER ; + pll->enable_bit =BM_PLL_ENABLE ;switch (type) {case IMX_PLLV3_GENERIC :
Signature · 1 line
2.20.1
PATCH v2 2/19 clk: imx: clk-imxrt1050: fix typo in clock name "video:"
In reply to Giulio Benetti"video:" must be "video", ":" is a typo.
--- drivers/clk/imx/clk-imxrt1050.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/clk/imx/clk-imxrt1050.c +1 -1
@@ -90,7 +90,7 @@ static const char *const usdhc_sels[] = { "pll2_pfd2_396m", "pll2_pfd0_352m", };static const char *const lpuart_sels[] = {"pll3_80m" ,"osc" , };static const char *const semc_alt_sels[] = {"pll2_pfd2_396m" ,"pll3_pfd1_664_62m" , };static const char *const semc_sels[] = {"periph_sel" ,"semc_alt_sel" , }; -static const char *const lcdif_sels[] = {"pll2_sys" ,"pll3_pfd3_454_74m" ,"pll5_video:" ,"pll2_pfd0_352m" ,"pll2_pfd1_594m" ,"pll3_pfd1_664_62m" }; +static const char *const lcdif_sels[] = {"pll2_sys" ,"pll3_pfd3_454_74m" ,"pll5_video" ,"pll2_pfd0_352m" ,"pll2_pfd1_594m" ,"pll3_pfd1_664_62m" };static int imxrt1050_clk_probe (struct udevice *dev) {
Signature · 1 line
2.20.1
PATCH v2 3/19 clk: imx: clk-imxrt1050: setup PLL5 for video in non-SPL
In reply to Giulio Benettimxsfb needs PLL5 as source, so let's setup it at its default frequency specified in RM(650Mhz).
---V1->V2:
* removed LCDIF set_parent() since it's setup in dts file(suggested by Fabio)
--- drivers/clk/imx/clk-imxrt1050.c | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-)
drivers/clk/imx/clk-imxrt1050.c +8 -1
@@ -238,9 +238,9 @@ static int imxrt1050_clk_probe(struct udevice *dev)clk_dm (IMXRT1050_CLK_LCDIF ,imx_clk_gate2 ("lcdif" ,"lcdif_podf" , base +0x70 ,28 )); -#ifdef CONFIG_SPL_BUILD struct clk *clk, *clk1; +#ifdef CONFIG_SPL_BUILD /* bypass pll1 before setting its rate */ clk_get_by_id (IMXRT1050_CLK_PLL1_REF_SEL , &clk);clk_get_by_id (IMXRT1050_CLK_PLL1_BYPASS , &clk1);
@@ -271,7 +271,14 @@ static int imxrt1050_clk_probe(struct udevice *dev)clk_get_by_id (IMXRT1050_CLK_PLL3_BYPASS , &clk1);clk_set_parent (clk1, clk); +#else +/* Set PLL5 for LCDIF to its default 650Mhz */ +clk_get_by_id (IMXRT1050_CLK_PLL5_VIDEO , &clk); +clk_enable (clk); +clk_set_rate (clk,650000000UL ); +clk_get_by_id (IMXRT1050_CLK_PLL5_BYPASS , &clk1); +clk_set_parent (clk1, clk);#endif return 0 ;
Signature · 1 line
2.20.1
PATCH v2 4/19 clk: imx: clk-imxrt1050: add set_parent() callback
In reply to Giulio BenettiNeed to add set_parent() callback to allow dts assigned-clock-parents to work so let's add it accordingly.
---V1->V2:
* introduce patch to allow clock's parent setting in dts to work
--- drivers/clk/imx/clk-imxrt1050.c | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+)
drivers/clk/imx/clk-imxrt1050.c +19 -0
@@ -71,11 +71,30 @@ static int imxrt1050_clk_enable(struct clk *clk)return __imxrt1050_clk_enable (clk,1 ); } +static int imxrt1050_clk_set_parent (struct clk *clk,struct clk *parent) +{ +struct clk *c, *cp; +int ret; + +debug ("%s(#%lu), parent: %lu\n" , __func__, clk->id, parent->id); + + ret =clk_get_by_id (clk->id, &c); +if (ret) +return ret; + + ret =clk_get_by_id (parent->id, &cp); +if (ret) +return ret; + +return clk_set_parent (c, cp); +} +static struct clk_ops imxrt1050_clk_ops = { .set_rate = imxrt1050_clk_set_rate, .get_rate = imxrt1050_clk_get_rate, .enable = imxrt1050_clk_enable, .disable = imxrt1050_clk_disable, + .set_parent = imxrt1050_clk_set_parent, };static const char *const pll_ref_sels[] = {"osc" ,"dummy" , };
Signature · 1 line
2.20.1
PATCH v2 4/19 clk: imx: clk-imxrt1050: add set_parent() callback
Hi Lukasz,
Quoted 37 lines · Giulio Benetti
Need to add
set_parent()callback to allow dts assigned-clock-parents to work so let's add it accordingly.Signed-off-by Giulio Benetti <[email protected]>---
V1->V2:
* introduce patch to allow clock's parent setting in dts to work--- drivers/clk/imx/clk-imxrt1050.c | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+)drivers/clk/imx/clk-imxrt1050.c +17
-0@@ -71,11 +71,30 @@ static int imxrt1050_clk_enable(struct clk *clk)return __imxrt1050_clk_enable (clk,1 ); } +static int imxrt1050_clk_set_parent (struct clk *clk,struct clk *parent) +{ +struct clk *c, *cp; +int ret; + +debug ("%s(#%lu), parent: %lu\n" , __func__, clk->id, parent->id); + + ret =clk_get_by_id (clk->id, &c); +if (ret) +return ret; + + ret =clk_get_by_id (parent->id, &cp); +if (ret) +return ret; + +return clk_set_parent (c, cp); +}
drivers/clk/imx/clk-imxrt1050.c static int imxrt1050_clk_enable(struct clk *clk) · line 100
Quoted 10 lines
drivers/clk/imx/clk-imxrt1050.c +2
-0+static struct clk_ops imxrt1050_clk_ops = { .set_rate = imxrt1050_clk_set_rate, .get_rate = imxrt1050_clk_get_rate, .enable = imxrt1050_clk_enable, .disable = imxrt1050_clk_disable, + .set_parent = imxrt1050_clk_set_parent, };static const char *const pll_ref_sels[] = {"osc" ,"dummy" , };
Can you please review this patch? There was not in previous patchset.
Thanks in advance
Kind regards
Signature · 2 lines
Giulio Benetti Benetti Engineering sas
PATCH v2 5/19 videomodes: add helper function to convert from ctfb to display_timing
In reply to Giulio BenettiThis function converts from "struct ctf_res_modes" to "struct display_timing".
--- drivers/video/videomodes.c | 29 +++++++++++++++++++++++++++++ drivers/video/videomodes.h | 3 +++ 2 files changed, 32 insertions(+)
drivers/video/videomodes.c +29 -0
@@ -444,3 +444,32 @@ int video_edid_dtd_to_ctfb_res_modes(struct edid_detailed_timing *t,return 0 ; } + +void video_ctfb_mode_to_display_timing (const struct ctfb_res_modes *mode, +struct display_timing *timing) +{ + timing->pixelclock.typ = mode->pixclock_khz *1000 ; + + timing->hactive.typ = mode->xres; + timing->hfront_porch.typ = mode->right_margin; + timing->hback_porch.typ = mode->left_margin; + timing->hsync_len.typ = mode->hsync_len; + + timing->vactive.typ = mode->yres; + timing->vfront_porch.typ = mode->lower_margin; + timing->vback_porch.typ = mode->upper_margin; + timing->vsync_len.typ = mode->vsync_len; + + timing->flags =0 ; + +if (mode->sync &FB_SYNC_HOR_HIGH_ACT ) + timing->flags |=DISPLAY_FLAGS_HSYNC_HIGH ; +else + timing->flags |=DISPLAY_FLAGS_HSYNC_LOW ; +if (mode->sync &FB_SYNC_VERT_HIGH_ACT ) + timing->flags |=DISPLAY_FLAGS_VSYNC_HIGH ; +else + timing->flags |=DISPLAY_FLAGS_VSYNC_LOW ; +if (mode->vmode ==FB_VMODE_INTERLACED ) + timing->flags |=DISPLAY_FLAGS_INTERLACED ; +}
drivers/video/videomodes.h +3 -0
@@ -92,3 +92,6 @@ int video_get_option_int(const char *options, const char *name, int def);int video_edid_dtd_to_ctfb_res_modes (struct edid_detailed_timing *t,struct ctfb_res_modes *mode); + +void video_ctfb_mode_to_display_timing (const struct ctfb_res_modes *mode, +struct display_timing *timing);
Signature · 1 line
2.20.1
PATCH v2 5/19 videomodes: add helper function to convert from ctfb to display_timing
Hi Giulio,
Quoted 52 lines · Giulio Benetti
This function converts from "struct
ctf_res_modes" to "structdisplay_timing".Signed-off-by Giulio Benetti <[email protected]>--- drivers/video/videomodes.c | 29 +++++++++++++++++++++++++++++ drivers/video/videomodes.h | 3 +++ 2 files changed, 32 insertions(+)drivers/video/videomodes.c +29
-0@@ -444,3 +444,32 @@ int video_edid_dtd_to_ctfb_res_modes(struct edid_detailed_timing *t,return 0 ; } + +void video_ctfb_mode_to_display_timing (const struct ctfb_res_modes *mode, +struct display_timing *timing) +{ + timing->pixelclock.typ = mode->pixclock_khz *1000 ; + + timing->hactive.typ = mode->xres; + timing->hfront_porch.typ = mode->right_margin; + timing->hback_porch.typ = mode->left_margin; + timing->hsync_len.typ = mode->hsync_len; + + timing->vactive.typ = mode->yres; + timing->vfront_porch.typ = mode->lower_margin; + timing->vback_porch.typ = mode->upper_margin; + timing->vsync_len.typ = mode->vsync_len; + + timing->flags =0 ; + +if (mode->sync &FB_SYNC_HOR_HIGH_ACT ) + timing->flags |=DISPLAY_FLAGS_HSYNC_HIGH ; +else + timing->flags |=DISPLAY_FLAGS_HSYNC_LOW ; +if (mode->sync &FB_SYNC_VERT_HIGH_ACT ) + timing->flags |=DISPLAY_FLAGS_VSYNC_HIGH ; +else + timing->flags |=DISPLAY_FLAGS_VSYNC_LOW ; +if (mode->vmode ==FB_VMODE_INTERLACED ) + timing->flags |=DISPLAY_FLAGS_INTERLACED ; +}drivers/video/videomodes.h +0
-0
drivers/video/videomodes.h int video_get_option_int(const char *options, const char *name, int def); · line 97
Quoted 6 lines
drivers/video/videomodes.h +3
-0@@ -92,3 +92,6 @@ int video_get_option_int(const char *options, const char *name, int def);int video_edid_dtd_to_ctfb_res_modes (struct edid_detailed_timing *t,struct ctfb_res_modes *mode); + +void video_ctfb_mode_to_display_timing (const struct ctfb_res_modes *mode, +struct display_timing *timing);
Please add a comment for this. What is ctfb?
Regards,
Simon
Quoted 1 line
PATCH v2 5/19 videomodes: add helper function to convert from ctfb to display_timing
Quoted 57 lines · Simon Glass
Hi Giulio,
Quoted 53 lines · Giulio Benetti
This function converts from "struct
ctf_res_modes" to "structdisplay_timing".Signed-off-by Giulio Benetti <[email protected]>--- drivers/video/videomodes.c | 29 +++++++++++++++++++++++++++++ drivers/video/videomodes.h | 3 +++ 2 files changed, 32 insertions(+)drivers/video/videomodes.c +29
-0@@ -444,3 +444,32 @@ int video_edid_dtd_to_ctfb_res_modes(struct edid_detailed_timing *t,return 0 ; } + +void video_ctfb_mode_to_display_timing (const struct ctfb_res_modes *mode, +struct display_timing *timing) +{ + timing->pixelclock.typ = mode->pixclock_khz *1000 ; + + timing->hactive.typ = mode->xres; + timing->hfront_porch.typ = mode->right_margin; + timing->hback_porch.typ = mode->left_margin; + timing->hsync_len.typ = mode->hsync_len; + + timing->vactive.typ = mode->yres; + timing->vfront_porch.typ = mode->lower_margin; + timing->vback_porch.typ = mode->upper_margin; + timing->vsync_len.typ = mode->vsync_len; + + timing->flags =0 ; + +if (mode->sync &FB_SYNC_HOR_HIGH_ACT ) + timing->flags |=DISPLAY_FLAGS_HSYNC_HIGH ; +else + timing->flags |=DISPLAY_FLAGS_HSYNC_LOW ; +if (mode->sync &FB_SYNC_VERT_HIGH_ACT ) + timing->flags |=DISPLAY_FLAGS_VSYNC_HIGH ; +else + timing->flags |=DISPLAY_FLAGS_VSYNC_LOW ; +if (mode->vmode ==FB_VMODE_INTERLACED ) + timing->flags |=DISPLAY_FLAGS_INTERLACED ; +}drivers/video/videomodes.h +0
-0@@ -92,3 +92,6 @@ int video_get_option_int(const char *options, const char *name, int def);
Quoted 7 lines
drivers/video/videomodes.h int video_get_option_int(const char *options, const char *name, int def); · line 97
Quoted 5 lines
drivers/video/videomodes.h +3
-0int video_edid_dtd_to_ctfb_res_modes (struct edid_detailed_timing *t,struct ctfb_res_modes *mode); + +void video_ctfb_mode_to_display_timing (const struct ctfb_res_modes *mode, +struct display_timing *timing);Please add a comment for this.
Ok
Quoted 1 line
What is ctfb?
If I'm not wrong it should stand for "Cathode Tube Frame Buffer" and it describes a Display(old Cathode Tube) Frame Buffer. This is at least what I've deducted :-)
Thanks for reviewing and
Best regards
Signature · 2 lines
Giulio Benetti Benetti Engineering sas
Quoted 4 lines
Regards,
SimonQuoted 1 line
PATCH v2 5/19 videomodes: add helper function to convert from ctfb to display_timing
Hi Giulio,
Quoted 67 lines · Giulio Benetti
Quoted 57 lines · Simon Glass
Hi Giulio,
Quoted 53 lines · Giulio Benetti
This function converts from "struct
ctf_res_modes" to "structdisplay_timing".Signed-off-by Giulio Benetti <[email protected]>--- drivers/video/videomodes.c | 29 +++++++++++++++++++++++++++++ drivers/video/videomodes.h | 3 +++ 2 files changed, 32 insertions(+)drivers/video/videomodes.c +29
-0@@ -444,3 +444,32 @@ int video_edid_dtd_to_ctfb_res_modes(struct edid_detailed_timing *t,return 0 ; } + +void video_ctfb_mode_to_display_timing (const struct ctfb_res_modes *mode, +struct display_timing *timing) +{ + timing->pixelclock.typ = mode->pixclock_khz *1000 ; + + timing->hactive.typ = mode->xres; + timing->hfront_porch.typ = mode->right_margin; + timing->hback_porch.typ = mode->left_margin; + timing->hsync_len.typ = mode->hsync_len; + + timing->vactive.typ = mode->yres; + timing->vfront_porch.typ = mode->lower_margin; + timing->vback_porch.typ = mode->upper_margin; + timing->vsync_len.typ = mode->vsync_len; + + timing->flags =0 ; + +if (mode->sync &FB_SYNC_HOR_HIGH_ACT ) + timing->flags |=DISPLAY_FLAGS_HSYNC_HIGH ; +else + timing->flags |=DISPLAY_FLAGS_HSYNC_LOW ; +if (mode->sync &FB_SYNC_VERT_HIGH_ACT ) + timing->flags |=DISPLAY_FLAGS_VSYNC_HIGH ; +else + timing->flags |=DISPLAY_FLAGS_VSYNC_LOW ; +if (mode->vmode ==FB_VMODE_INTERLACED ) + timing->flags |=DISPLAY_FLAGS_INTERLACED ; +}drivers/video/videomodes.h +0
-0@@ -92,3 +92,6 @@ int video_get_option_int(const char *options, const char *name, int def);Quoted 7 lines
drivers/video/videomodes.h int video_get_option_int(const char *options, const char *name, int def); · line 97
Quoted 5 lines
drivers/video/videomodes.h +3
-0int video_edid_dtd_to_ctfb_res_modes (struct edid_detailed_timing *t,struct ctfb_res_modes *mode); + +void video_ctfb_mode_to_display_timing (const struct ctfb_res_modes *mode, +struct display_timing *timing);Please add a comment for this.
Quoted 7 lines
Ok
Quoted 1 line
What is ctfb?
If I'm not wrong it should stand for "Cathode Tube Frame Buffer" and it describes a Display(old Cathode Tube) Frame Buffer. This is at least what I've deducted :-)
OK certainly plausible! Then you should add it to your comment somewhere.
Regards,
Simon
PATCH v2 5/19 videomodes: add helper function to convert from ctfb to display_timing
Quoted 73 lines · Simon Glass
Hi Giulio,
Quoted 69 lines · Giulio Benetti
Quoted 57 lines · Simon Glass
Hi Giulio,
Quoted 53 lines · Giulio Benetti
This function converts from "struct
ctf_res_modes" to "structdisplay_timing".Signed-off-by Giulio Benetti <[email protected]>--- drivers/video/videomodes.c | 29 +++++++++++++++++++++++++++++ drivers/video/videomodes.h | 3 +++ 2 files changed, 32 insertions(+)drivers/video/videomodes.c +29
-0@@ -444,3 +444,32 @@ int video_edid_dtd_to_ctfb_res_modes(struct edid_detailed_timing *t,return 0 ; } + +void video_ctfb_mode_to_display_timing (const struct ctfb_res_modes *mode, +struct display_timing *timing) +{ + timing->pixelclock.typ = mode->pixclock_khz *1000 ; + + timing->hactive.typ = mode->xres; + timing->hfront_porch.typ = mode->right_margin; + timing->hback_porch.typ = mode->left_margin; + timing->hsync_len.typ = mode->hsync_len; + + timing->vactive.typ = mode->yres; + timing->vfront_porch.typ = mode->lower_margin; + timing->vback_porch.typ = mode->upper_margin; + timing->vsync_len.typ = mode->vsync_len; + + timing->flags =0 ; + +if (mode->sync &FB_SYNC_HOR_HIGH_ACT ) + timing->flags |=DISPLAY_FLAGS_HSYNC_HIGH ; +else + timing->flags |=DISPLAY_FLAGS_HSYNC_LOW ; +if (mode->sync &FB_SYNC_VERT_HIGH_ACT ) + timing->flags |=DISPLAY_FLAGS_VSYNC_HIGH ; +else + timing->flags |=DISPLAY_FLAGS_VSYNC_LOW ; +if (mode->vmode ==FB_VMODE_INTERLACED ) + timing->flags |=DISPLAY_FLAGS_INTERLACED ; +}drivers/video/videomodes.h +0
-0@@ -92,3 +92,6 @@ int video_get_option_int(const char *options, const char *name, int def);Quoted 7 lines
drivers/video/videomodes.h int video_get_option_int(const char *options, const char *name, int def); · line 97
Quoted 5 lines
drivers/video/videomodes.h +3
-0int video_edid_dtd_to_ctfb_res_modes (struct edid_detailed_timing *t,struct ctfb_res_modes *mode); + +void video_ctfb_mode_to_display_timing (const struct ctfb_res_modes *mode, +struct display_timing *timing);Please add a comment for this.
Ok
Quoted 7 lines
Quoted 5 lines
Quoted 1 line
What is ctfb?
If I'm not wrong it should stand for "Cathode Tube Frame Buffer" and it describes a Display(old Cathode Tube) Frame Buffer. This is at least what I've deducted :-)
OK certainly plausible! Then you should add it to your comment somewhere.
Perfect, done while describing what functions does in Doxygen style!
Best regards
Signature · 2 lines
Giulio Benetti Benetti Engineering sas
Quoted 3 lines
Regards,
Simon
PATCH v2 6/19 sunxi: display: use common video_ctfb_mode_to_display_timing()
In reply to Giulio BenettiSince video_ctfb_mode_to_display_timing() has been implemented by moving sunxi_ctfb_mode_to_display_timing() to video_modes.c and it's meant to be used by other video subsystem, let's use it instead of local sunxi_ctfb_mode_to_display_timing().
--- drivers/video/sunxi/sunxi_display.c | 33 ++--------------------------- 1 file changed, 2 insertions(+), 31 deletions(-)
drivers/video/sunxi/sunxi_display.c +2 -31
@@ -615,35 +615,6 @@ static void sunxi_lcdc_backlight_enable(void)gpio_direction_output (pin,PWM_ON ); } -static void sunxi_ctfb_mode_to_display_timing (const struct ctfb_res_modes *mode, -struct display_timing *timing) -{ - timing->pixelclock.typ = mode->pixclock_khz *1000 ; - - timing->hactive.typ = mode->xres; - timing->hfront_porch.typ = mode->right_margin; - timing->hback_porch.typ = mode->left_margin; - timing->hsync_len.typ = mode->hsync_len; - - timing->vactive.typ = mode->yres; - timing->vfront_porch.typ = mode->lower_margin; - timing->vback_porch.typ = mode->upper_margin; - timing->vsync_len.typ = mode->vsync_len; - - timing->flags =0 ; - -if (mode->sync &FB_SYNC_HOR_HIGH_ACT ) - timing->flags |=DISPLAY_FLAGS_HSYNC_HIGH ; -else - timing->flags |=DISPLAY_FLAGS_HSYNC_LOW ; -if (mode->sync &FB_SYNC_VERT_HIGH_ACT ) - timing->flags |=DISPLAY_FLAGS_VSYNC_HIGH ; -else - timing->flags |=DISPLAY_FLAGS_VSYNC_LOW ; -if (mode->vmode ==FB_VMODE_INTERLACED ) - timing->flags |=DISPLAY_FLAGS_INTERLACED ; -} -static void sunxi_lcdc_tcon0_mode_set (const struct ctfb_res_modes *mode,bool for_ext_vga_dac) {
@@ -673,7 +644,7 @@ static void sunxi_lcdc_tcon0_mode_set(const struct ctfb_res_modes *mode,lcdc_pll_set (ccm,0 , mode->pixclock_khz, &clk_div, &clk_double,sunxi_is_composite ()); -sunxi_ctfb_mode_to_display_timing (mode, &timing); +video_ctfb_mode_to_display_timing (mode, &timing);lcdc_tcon0_mode_set (lcdc, &timing, clk_div, for_ext_vga_dac, sunxi_display.depth,CONFIG_VIDEO_LCD_DCLK_PHASE ); }
@@ -689,7 +660,7 @@ static void sunxi_lcdc_tcon1_mode_set(const struct ctfb_res_modes *mode, (struct sunxi_ccm_reg *)SUNXI_CCM_BASE ;struct display_timing timing; -sunxi_ctfb_mode_to_display_timing (mode, &timing); +video_ctfb_mode_to_display_timing (mode, &timing);lcdc_tcon1_mode_set (lcdc, &timing, use_portd_hvsync,sunxi_is_composite ());
Signature · 1 line
2.20.1
PATCH v2 7/19 video: mxsfb: add support for DM CLK
In reply to Giulio BenettiAllow using DM CLK instead of mxs_set_lcdclk() so we can avoid to implement a special function to set lcd clock on i.MXRT.
--- drivers/video/mxsfb.c | 30 +++++++++++++++++++++++++----- 1 file changed, 25 insertions(+), 5 deletions(-)
drivers/video/mxsfb.c +25 -5
@@ -5,6 +5,7 @@* Copyright (C) 2011-2013 Marek Vasut <[email protected]> */ #include <common.h> +#include <clk.h> #include <dm.h> #include <env.h> #include <dm/device_compat.h>
@@ -52,14 +53,32 @@ __weak void mxsfb_system_setup(void)* le:89,ri:164,up:23,lo:10,hs:10,vs:10,sync:0,vmode:0 */ -static void mxs_lcd_init (u32 fb_addr,struct ctfb_res_modes *mode,int bpp) +static void mxs_lcd_init (struct udevice *dev,u32 fb_addr, +struct ctfb_res_modes *mode,int bpp) {struct mxs_lcdif_regs *regs = (struct mxs_lcdif_regs *)MXS_LCDIF_BASE ;uint32_t word_len =0 , bus_width =0 ;uint8_t valid_data =0 ; +#if CONFIG_IS_ENABLED (CLK ) +struct clk per_clk; +int ret; + + ret =clk_get_by_name (dev,"per" , &per_clk); +if (ret) { +dev_err (dev,"Failed to get mxs clk: %d\n" , ret); +return ; + } + + ret =clk_set_rate (&per_clk,PS2KHZ (mode->pixclock) *1000 ); +if (ret <0 ) { +dev_err (dev,"Failed to set mxs clk: %d\n" , ret); +return ; + } +#else /* Kick in the LCDIF clock */ mxs_set_lcdclk (MXS_LCDIF_BASE ,PS2KHZ (mode->pixclock)); +#endif /* Restart the LCDIF block */ mxs_reset_block (®s->hw_lcdif_ctrl_reg);
@@ -135,10 +154,11 @@ static void mxs_lcd_init(u32 fb_addr, struct ctfb_res_modes *mode, int bpp)writel (LCDIF_CTRL_RUN , ®s->hw_lcdif_ctrl_set); } -static int mxs_probe_common (struct ctfb_res_modes *mode,int bpp,u32 fb) +static int mxs_probe_common (struct udevice *dev,struct ctfb_res_modes *mode, +int bpp,u32 fb) {/* Start framebuffer */ -mxs_lcd_init (fb, mode, bpp); +mxs_lcd_init (dev, fb, mode, bpp);#ifdef CONFIG_VIDEO_MXS_MODE_SYSTEM /*
@@ -260,7 +280,7 @@ void *video_hw_init(void)printf ("%s\n" , panel.modeIdent); - ret =mxs_probe_common (&mode, bpp, (u32 )fb); + ret =mxs_probe_common (NULL , &mode, bpp, (u32 )fb);if (ret) goto dealloc_fb;
@@ -337,7 +357,7 @@ static int mxs_video_probe(struct udevice *dev) mode.vsync_len = timings.vsync_len.typ; mode.pixclock =HZ2PS (timings.pixelclock.typ); - ret =mxs_probe_common (&mode, bpp, plat->base); + ret =mxs_probe_common (dev, &mode, bpp, plat->base);if (ret)return ret;
Signature · 1 line
2.20.1
PATCH v2 8/19 video: mxsfb: add support for i.MXRT
In reply to Giulio BenettiAdd support for i.MXRT by adding CONFIG_IMXRT in register structure and adding .compatible = "fsl,imxrt-lcdif".
--- arch/arm/include/asm/arch-imxrt/imx-regs.h | 6 ++++++ arch/arm/include/asm/mach-imx/regs-lcdif.h | 6 +++--- drivers/video/mxsfb.c | 1 + 3 files changed, 10 insertions(+), 3 deletions(-)
arch/arm/include/asm/arch-imxrt/imx-regs.h +6 -0
@@ -17,4 +17,10 @@#define ANATOP_BASE_ADDR 0x400d8000 +#define MXS_LCDIF_BASE 0x402b8000 + +#if !(defined(__KERNEL_STRICT_NAMES) || defined(__ASSEMBLY__)) +#include <asm/mach-imx/regs-lcdif.h> +#endif +#endif /* __ASM_ARCH_IMX_REGS_H__ */
arch/arm/include/asm/mach-imx/regs-lcdif.h +3 -3
@@ -22,7 +22,7 @@ struct mxs_lcdif_regs {defined (CONFIG_MX6SL ) ||defined (CONFIG_MX6SLL ) || \defined (CONFIG_MX6UL ) ||defined (CONFIG_MX6ULL ) || \defined (CONFIG_MX7 ) ||defined (CONFIG_MX7ULP ) || \ - defined(CONFIG_IMX8M) + defined(CONFIG_IMX8M) || defined(CONFIG_IMXRT) mxs_reg_32(hw_lcdif_ctrl2) /* 0x20 */#endif mxs_reg_32 (hw_lcdif_transfer_count)/* 0x20/0x30 */
@@ -49,7 +49,7 @@ struct mxs_lcdif_regs { mxs_reg_32(hw_lcdif_csc_coeffctrl2) /* 0x130 */ mxs_reg_32(hw_lcdif_csc_coeffctrl3) /* 0x140 */ mxs_reg_32(hw_lcdif_csc_coeffctrl4) /* 0x150 */ - mxs_reg_32(hw_lcdif_csc_offset) /* 0x160 */ + mxs_reg_32(hw_lcdif_csc_offset) /* 0x160 */ mxs_reg_32(hw_lcdif_csc_limit) /* 0x170 */ #if defined(CONFIG_MX23)
@@ -61,7 +61,7 @@ struct mxs_lcdif_regs {defined (CONFIG_MX6SL ) ||defined (CONFIG_MX6SLL ) || \defined (CONFIG_MX6UL ) ||defined (CONFIG_MX6ULL ) || \defined (CONFIG_MX7 ) ||defined (CONFIG_MX7ULP ) || \ - defined(CONFIG_IMX8M) + defined(CONFIG_IMX8M) || defined(CONFIG_IMXRT) mxs_reg_32(hw_lcdif_crc_stat) /* 0x1a0 */#endif mxs_reg_32 (hw_lcdif_lcdif_stat)/* 0x1d0/0x1b0 */
drivers/video/mxsfb.c +1 -0
@@ -440,6 +440,7 @@ static const struct udevice_id mxs_video_ids[] = { { .compatible = "fsl,imx23-lcdif" }, { .compatible = "fsl,imx28-lcdif" }, { .compatible = "fsl,imx7ulp-lcdif" }, + { .compatible = "fsl,imxrt-lcdif" }, {/* sentinel */ } };
Signature · 1 line
2.20.1
PATCH v2 9/19 video: mxsfb: refactor for using display_timings
In reply to Giulio Benettistruct display_timings provides more informations such clock and DE polarity, so let's refactor the code to use struct display_timings instead of struct ctfb_res_modes, so we'll become able to get clock and DE polarity settings and set register according to them in the next patch.
--- drivers/video/mxsfb.c | 54 ++++++++++++++++++------------------------- 1 file changed, 23 insertions(+), 31 deletions(-)
drivers/video/mxsfb.c +23 -31
@@ -54,7 +54,7 @@ __weak void mxsfb_system_setup(void)*/ static void mxs_lcd_init (struct udevice *dev,u32 fb_addr, -struct ctfb_res_modes *mode,int bpp) +struct display_timing *timings,int bpp) {struct mxs_lcdif_regs *regs = (struct mxs_lcdif_regs *)MXS_LCDIF_BASE ;uint32_t word_len =0 , bus_width =0 ;
@@ -70,14 +70,14 @@ static void mxs_lcd_init(struct udevice *dev, u32 fb_addr, return; } - ret =clk_set_rate (&per_clk,PS2KHZ (mode->pixclock) *1000 ); + ret =clk_set_rate (&per_clk, timings->pixelclock.typ);if (ret <0 ) {dev_err (dev,"Failed to set mxs clk: %d\n" , ret);return ; }#else /* Kick in the LCDIF clock */ -mxs_set_lcdclk (MXS_LCDIF_BASE ,PS2KHZ (mode->pixclock)); +mxs_set_lcdclk (MXS_LCDIF_BASE , timings->pixelclock.typ /1000 );#endif /* Restart the LCDIF block */
@@ -115,25 +115,25 @@ static void mxs_lcd_init(struct udevice *dev, u32 fb_addr,mxsfb_system_setup (); -writel ((mode->yres <<LCDIF_TRANSFER_COUNT_V_COUNT_OFFSET ) | mode->xres, - ®s->hw_lcdif_transfer_count); +writel ((timings->vactive.typ <<LCDIF_TRANSFER_COUNT_V_COUNT_OFFSET ) | + timings->hactive.typ, ®s->hw_lcdif_transfer_count);writel (LCDIF_VDCTRL0_ENABLE_PRESENT |LCDIF_VDCTRL0_ENABLE_POL |LCDIF_VDCTRL0_VSYNC_PERIOD_UNIT |LCDIF_VDCTRL0_VSYNC_PULSE_WIDTH_UNIT | - mode->vsync_len, ®s->hw_lcdif_vdctrl0); -writel (mode->upper_margin + mode->lower_margin + - mode->vsync_len + mode->yres, + timings->vsync_len.typ, ®s->hw_lcdif_vdctrl0); +writel (timings->vback_porch.typ + timings->vfront_porch.typ + + timings->vsync_len.typ + timings->vactive.typ, ®s->hw_lcdif_vdctrl1); -writel ((mode->hsync_len <<LCDIF_VDCTRL2_HSYNC_PULSE_WIDTH_OFFSET ) | - (mode->left_margin + mode->right_margin + - mode->hsync_len + mode->xres), +writel ((timings->hsync_len.typ <<LCDIF_VDCTRL2_HSYNC_PULSE_WIDTH_OFFSET ) | + (timings->hback_porch.typ + timings->hfront_porch.typ + + timings->hsync_len.typ + timings->hactive.typ), ®s->hw_lcdif_vdctrl2); -writel (((mode->left_margin + mode->hsync_len) << +writel (((timings->hback_porch.typ + timings->hsync_len.typ) <<LCDIF_VDCTRL3_HORIZONTAL_WAIT_CNT_OFFSET ) | - (mode->upper_margin + mode->vsync_len), + (timings->vback_porch.typ + timings->vsync_len.typ), ®s->hw_lcdif_vdctrl3); -writel ((0 <<LCDIF_VDCTRL4_DOTCLK_DLY_SEL_OFFSET ) | mode->xres, +writel ((0 <<LCDIF_VDCTRL4_DOTCLK_DLY_SEL_OFFSET ) | timings->hactive.typ, ®s->hw_lcdif_vdctrl4);writel (fb_addr, ®s->hw_lcdif_cur_buf);
@@ -154,11 +154,11 @@ static void mxs_lcd_init(struct udevice *dev, u32 fb_addr,writel (LCDIF_CTRL_RUN , ®s->hw_lcdif_ctrl_set); } -static int mxs_probe_common (struct udevice *dev,struct ctfb_res_modes *mode, +static int mxs_probe_common (struct udevice *dev,struct display_timing *timings,int bpp,u32 fb) {/* Start framebuffer */ -mxs_lcd_init (dev, fb, mode, bpp); +mxs_lcd_init (dev, fb, timings, bpp);#ifdef CONFIG_VIDEO_MXS_MODE_SYSTEM /*
@@ -224,6 +224,7 @@ void *video_hw_init(void)char *penv;void *fb =NULL ;struct ctfb_res_modes mode; +struct display_timing timings;puts ("Video: " );
@@ -280,7 +281,9 @@ void *video_hw_init(void)printf ("%s\n" , panel.modeIdent); - ret =mxs_probe_common (NULL , &mode, bpp, (u32 )fb); +video_ctfb_mode_to_display_timing (&mode, &timings); + + ret =mxs_probe_common (NULL , &timings, bpp, (u32 )fb);if (ret) goto dealloc_fb;
@@ -334,7 +337,6 @@ static int mxs_video_probe(struct udevice *dev)struct video_uc_platdata *plat =dev_get_uclass_platdata (dev);struct video_priv *uc_priv =dev_get_uclass_priv (dev); -struct ctfb_res_modes mode;struct display_timing timings;u32 bpp =0 ;u32 fb_start, fb_end;
@@ -347,17 +349,7 @@ static int mxs_video_probe(struct udevice *dev)if (ret)return ret; - mode.xres = timings.hactive.typ; - mode.yres = timings.vactive.typ; - mode.left_margin = timings.hback_porch.typ; - mode.right_margin = timings.hfront_porch.typ; - mode.upper_margin = timings.vback_porch.typ; - mode.lower_margin = timings.vfront_porch.typ; - mode.hsync_len = timings.hsync_len.typ; - mode.vsync_len = timings.vsync_len.typ; - mode.pixclock =HZ2PS (timings.pixelclock.typ); - - ret =mxs_probe_common (dev, &mode, bpp, plat->base); + ret =mxs_probe_common (dev, &timings, bpp, plat->base);if (ret)return ret;
@@ -378,8 +370,8 @@ static int mxs_video_probe(struct udevice *dev)return -EINVAL ; } - uc_priv->xsize = mode.xres; - uc_priv->ysize = mode.yres; + uc_priv->xsize = timings.hactive.typ; + uc_priv->ysize = timings.vactive.typ;/* Enable dcache for the frame buffer */ fb_start = plat->base & ~(MMU_SECTION_SIZE -1 );
Signature · 1 line
2.20.1
PATCH v2 10/19 video: mxsfb: enable setting HSYNC negative polarity
In reply to Giulio BenettiHSYNC signal can now be flipped according to display_flags bitmaks by writing its bitmask on vdctrl0 register.
--- drivers/video/mxsfb.c | 14 ++++++++++---- 1 file changed, 10 insertions(+), 4 deletions(-)
drivers/video/mxsfb.c +10 -4
@@ -57,8 +57,10 @@ static void mxs_lcd_init(struct udevice *dev, u32 fb_addr, struct display_timing *timings, int bpp) {struct mxs_lcdif_regs *regs = (struct mxs_lcdif_regs *)MXS_LCDIF_BASE ; +const enum display_flags flags = timings->flags;uint32_t word_len =0 , bus_width =0 ;uint8_t valid_data =0 ; +uint32_t vdctrl0;#if CONFIG_IS_ENABLED (CLK )struct clk per_clk;
@@ -118,10 +120,14 @@ static void mxs_lcd_init(struct udevice *dev, u32 fb_addr,writel ((timings->vactive.typ <<LCDIF_TRANSFER_COUNT_V_COUNT_OFFSET ) | timings->hactive.typ, ®s->hw_lcdif_transfer_count); -writel (LCDIF_VDCTRL0_ENABLE_PRESENT |LCDIF_VDCTRL0_ENABLE_POL | -LCDIF_VDCTRL0_VSYNC_PERIOD_UNIT | -LCDIF_VDCTRL0_VSYNC_PULSE_WIDTH_UNIT | - timings->vsync_len.typ, ®s->hw_lcdif_vdctrl0); + vdctrl0 =LCDIF_VDCTRL0_ENABLE_PRESENT |LCDIF_VDCTRL0_ENABLE_POL | +LCDIF_VDCTRL0_VSYNC_PERIOD_UNIT | +LCDIF_VDCTRL0_VSYNC_PULSE_WIDTH_UNIT | + timings->vsync_len.typ; + +if (flags &DISPLAY_FLAGS_HSYNC_HIGH ) + vdctrl0 |=LCDIF_VDCTRL0_HSYNC_POL ; +writel (vdctrl0, ®s->hw_lcdif_vdctrl0);writel (timings->vback_porch.typ + timings->vfront_porch.typ + timings->vsync_len.typ + timings->vactive.typ, ®s->hw_lcdif_vdctrl1);
Signature · 1 line
2.20.1
PATCH v2 11/19 video: mxsfb: enable setting VSYNC negative polarity
In reply to Giulio BenettiVSYNC signal can now be flipped by writing its bitmask on vdctrl0 register.
--- drivers/video/mxsfb.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/video/mxsfb.c +2 -0
@@ -127,6 +127,8 @@ static void mxs_lcd_init(struct udevice *dev, u32 fb_addr,if (flags &DISPLAY_FLAGS_HSYNC_HIGH ) vdctrl0 |=LCDIF_VDCTRL0_HSYNC_POL ; +if (flags &DISPLAY_FLAGS_VSYNC_HIGH ) + vdctrl0 |=LCDIF_VDCTRL0_VSYNC_POL ;writel (vdctrl0, ®s->hw_lcdif_vdctrl0); writel(timings->vback_porch.typ + timings->vfront_porch.typ + timings->vsync_len.typ + timings->vactive.typ,
Signature · 1 line
2.20.1
PATCH v2 12/19 video: mxsfb: enable setting PIXDATA on negative edge
In reply to Giulio BenettiDOTCLK signal can now be flipped by writing its bitmask on vdctrl0 register.
--- drivers/video/mxsfb.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/video/mxsfb.c +2 -0
@@ -129,6 +129,8 @@ static void mxs_lcd_init(struct udevice *dev, u32 fb_addr, vdctrl0 |=LCDIF_VDCTRL0_HSYNC_POL ;if (flags &DISPLAY_FLAGS_VSYNC_HIGH ) vdctrl0 |=LCDIF_VDCTRL0_VSYNC_POL ; +if (flags &DISPLAY_FLAGS_PIXDATA_NEGEDGE ) + vdctrl0 |=LCDIF_VDCTRL0_DOTCLK_POL ;writel (vdctrl0, ®s->hw_lcdif_vdctrl0); writel(timings->vback_porch.typ + timings->vfront_porch.typ + timings->vsync_len.typ + timings->vactive.typ,
Signature · 1 line
2.20.1
PATCH v2 13/19 video: mxsfb: enable setting ENABLE negative polarity
In reply to Giulio BenettiENABLE signal can now be flipped by writing its bitmask on vdctrl0 register.
--- drivers/video/mxsfb.c | 3 +++ 1 file changed, 3 insertions(+)
drivers/video/mxsfb.c +3 -0
@@ -131,6 +131,9 @@ static void mxs_lcd_init(struct udevice *dev, u32 fb_addr, vdctrl0 |=LCDIF_VDCTRL0_VSYNC_POL ;if (flags &DISPLAY_FLAGS_PIXDATA_NEGEDGE ) vdctrl0 |=LCDIF_VDCTRL0_DOTCLK_POL ; +if (flags &DISPLAY_FLAGS_DE_HIGH ) + vdctrl0 |=LCDIF_VDCTRL0_ENABLE_POL ; +writel (vdctrl0, ®s->hw_lcdif_vdctrl0); writel(timings->vback_porch.typ + timings->vfront_porch.typ + timings->vsync_len.typ + timings->vactive.typ,
Signature · 1 line
2.20.1
PATCH v2 14/19 imxrt1050_evk: add 16bpp video support if video layer enabled
In reply to Giulio Benettii.MXRT1050 provides mxsfb compatible lcd controller, so let's enable video mxsfb driver with 16bpp depth if CONFIG_DM_VIDEO is selected since board has 16bpp only connection.
--- include/configs/imxrt1050-evk.h | 15 +++++++++++++++ 1 file changed, 15 insertions(+)
include/configs/imxrt1050-evk.h +15 -0
@@ -30,6 +30,21 @@#define CONFIG_SYS_MMC_ENV_DEV 0/* USDHC1 */ +#ifdef CONFIG_DM_VIDEO +#define CONFIG_VIDEO_MXS +#define CONFIG_VIDEO_LOGO +#define CONFIG_SPLASH_SCREEN +#define CONFIG_SPLASH_SCREEN_ALIGN +#define CONFIG_BMP_16BPP +#define CONFIG_VIDEO_BMP_RLE8 +#define CONFIG_VIDEO_BMP_LOGO + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "stdin=serial\0" \ + "stdout=serial,vidconsole\0" \ + "stderr=serial,vidconsole\0" +#endif +/* * Configuration of the external SDRAM memory */
Signature · 1 line
2.20.1
PATCH v2 15/19 ARM: dts: i.mxrt1050: add lcdif node
In reply to Giulio BenettiAdd lcdif node to SoC.
--- arch/arm/dts/imxrt1050.dtsi | 10 ++++++++++ 1 file changed, 10 insertions(+)
arch/arm/dts/imxrt1050.dtsi +10 -0
@@ -13,6 +13,7 @@ / { aliases { + display0 = &lcdif; gpio0 = &gpio1; gpio1 = &gpio2; gpio2 = &gpio3;
@@ -142,5 +143,14 @@ interrupt-controller; #interrupt-cells = <2>; }; + + lcdif: lcdif at 402b8000 { + compatible = "fsl,imxrt-lcdif"; + reg = <0x402b8000 0x10000>; + interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMXRT1050_CLK_LCDIF>; + clock-names = "per"; + status = "disabled"; + }; }; };
Signature · 1 line
2.20.1
v2 cover i.MXRT1050 add LCDIF support
In reply to Giulio BenettiThis patchset passed travis:
https://travis-ci.org/github/giuliobenetti/u-boot-imxrt/builds/665577905?utm_medium=notification&utm_source=email
And also:./tools/buildman/buildman.py --branch=dev/imxrt-lcdif odroid edison trats trats2 imxrt --show_errors --force-build --count=19 --output-dir=../BUILD/
Best regards
Signature · 2 lines
Giulio Benetti Benetti Engineering sas
Quoted 53 lines · Giulio Benetti
This patchset add support for LCDIF on i.MXRT1050 evk. This requires PLL5 to be setup, mxsfb needs to use
display_timingto retrieve if Lcd has inverted PIXCLOCK from dts.With this patchset applied we temporary loose DCache support until it will get implemented, since a function in
mxsfb.cis needed for setting cache behaviour. Anyway this way Lcd will show the console same way as serial does.Also I've moved private
sunxi_ctfb_mode_to_display_timing()to videomodes since I need it formxfsb.ctoo, then having a unified function to convert fromctfb_modetodisplay_timing.Changes:
V1->V2:
* moved hard-coded LCDIF's parent clock fromclk-imxrt1050.ctoimxrt1050-evk.dts
* reworded some commit logGiulio Benetti (19):
clk: imx: pllv3: addenable_bit
clk: imx: clk-imxrt1050: fix typo in clock name "video:"
clk: imx: clk-imxrt1050: setup PLL5 for video in non-SPL
clk: imx: clk-imxrt1050: addset_parent()callback
videomodes: add helper function to convert from ctfb todisplay_timing
sunxi: display: use commonvideo_ctfb_mode_to_display_timing()
video: mxsfb: add support for DM CLK
video: mxsfb: add support for i.MXRT
video: mxsfb: refactor for usingdisplay_timings
video: mxsfb: enable setting HSYNC negative polarity
video: mxsfb: enable setting VSYNC negative polarity
video: mxsfb: enable setting PIXDATA on negative edge
video: mxsfb: enable setting ENABLE negative polarity
imxrt1050_evk: add 16bpp video support if video layer enabled
ARM: dts: i.mxrt1050: add lcdif node
ARM: dts: imxrt1050: allow this dtsi file to be compiled in Linux
arch: arm: dts: imxrt1050-evk: add lcdif node
configs: imxrt1050-evk: enable video support/console
configs: imxrt1050-evk: temporary disable DCACHEarch/arm/dts/imxrt1050-evk.dts | 60 ++++++++++++++ arch/arm/dts/imxrt1050.dtsi | 14 +++- arch/arm/include/asm/arch-imxrt/imx-regs.h | 6 ++ arch/arm/include/asm/mach-imx/regs-lcdif.h | 6 +- configs/imxrt1050-evk_defconfig | 6 ++ drivers/clk/imx/clk-imxrt1050.c | 30 ++++++- drivers/clk/imx/clk-pllv3.c | 9 +++ drivers/video/mxsfb.c | 94 ++++++++++++++-------- drivers/video/sunxi/sunxi_display.c | 33 +------- drivers/video/videomodes.c | 29 +++++++ drivers/video/videomodes.h | 3 + include/configs/imxrt1050-evk.h | 15 ++++ 12 files changed, 234 insertions(+), 71 deletions(-)
v2 cover i.MXRT1050 add LCDIF support
Kindly ping
Signature · 2 lines
Giulio Benetti Benetti Engineering sas
Quoted 10 lines · Giulio Benetti
This patchset passed travis:
https://travis-ci.org/github/giuliobenetti/u-boot-imxrt/builds/665577905?utm_medium=notification&utm_source=emailAnd also:
./tools/buildman/buildman.py--branch=dev/imxrt-lcdif odroid edison trats trats2 imxrt --show_errors --force-build --count=19 --output-dir=../BUILD/Best regards
v2 cover i.MXRT1050 add LCDIF support
I've pinged the wrong patchset, sorry for the noise, the right one is v3.
Signature · 2 lines
Giulio Benetti Benetti Engineering sas
Quoted 2 lines · Giulio Benetti
Kindly ping
v2 cover i.MXRT1050 add LCDIF support
Hi Giulio,
Quoted 11 lines · Giulio Benetti
I've pinged the wrong patchset, sorry for the noise, the right one is v3.
--
Giulio Benetti
Benetti Engineering sasQuoted 2 lines · Giulio Benetti
Kindly ping
Who are you pinging? Who is the maintainer?
Regards,
Simon
v2 cover i.MXRT1050 add LCDIF support
Quoted 11 lines · Simon Glass
Hi Giulio,
Quoted 7 lines · Giulio Benetti
I've pinged the wrong patchset, sorry for the noise, the right one is v3.
--
Giulio Benetti
Benetti Engineering sas
Quoted 6 lines
Quoted 4 lines · Giulio Benetti
Quoted 2 lines
Kindly ping
Who are you pinging? Who is the maintainer?
Ah I didn't know I had to point someone.
So in this case would be either Stefano or Fabio and indeed Fabio answered before here:
https://lists.denx.de/pipermail/u-boot/2020-April/406857.html
Signature · 2 lines
Giulio Benetti Benetti Engineering sas
Fabio Estevam
reviewerv2 cover i.MXRT1050 add LCDIF support
Hi Giulio,
Quoted 5 lines · Giulio Benetti
Ah I didn't know I had to point someone.
So in this case would be either Stefano or Fabio and indeed Fabio answered before here:
https://lists.denx.de/pipermail/u-boot/2020-April/406857.html
Since this series touches video, clock and i.MX, we still need to get some feedback from Anatolij and Lukasz.
Thanks
v2 cover i.MXRT1050 add LCDIF support
Hi Fabio, Simon and Anatolij,
Quoted 5 lines · Fabio Estevam
Hi Giulio,
On Thu, Apr 16, 2020 at 12:20 PM Giulio Benetti
<[email protected]> wrote:
Quoted 8 lines
Quoted 5 lines
Ah I didn't know I had to point someone.
So in this case would be either Stefano or Fabio and indeed Fabio answered before here:
https://lists.denx.de/pipermail/u-boot/2020-April/406857.htmlSince this series touches video, clock and i.MX, we still need to get some feedback from Anatolij and Lukasz.
Lukasz already reviewed his patches, only Anatolij is missing.
Anatolij, can you please take a look at video patches on this patchset? Thanks in advance
Best regards
Signature · 2 lines
Giulio Benetti Benetti Engineering sas