ARM: dts: stm32: Use DT alias for the configuration EEPROM
Subsystems (3)
PATCH 1/1 ARM: dts: stm32: Use DT alias for the configuration EEPROM
Use DT /aliases node to establish a stable phandle to the configuration EEPROM. This permits the configuration EEPROM to be moved e.g. to a different address or a different bus. Adjust the board code to handle new phandle lookup.
Signed-off-by Marek Vasut <[email protected]>
Cc Patrick Delaunay <[email protected]>
Cc Patrice Chotard <[email protected]>
--- arch/arm/dts/stm32mp15xx-dhcom.dtsi | 6 +++++- board/dhelectronics/dh_stm32mp1/board.c | 15 +++++++-------- 2 files changed, 12 insertions(+), 9 deletions(-)
arch/arm/dts/stm32mp15xx-dhcom.dtsi +5 -1
@@ -10,6 +10,10 @@ #include <dt-bindings/mfd/st,stpmic1.h> / { + aliases { + eeprom0 = &eeprom0; + }; + memory at c0000000 { device_type = "memory"; reg = <0xC0000000 0x40000000>;
@@ -187,7 +191,7 @@ }; }; - eeprom at 50 { + eeprom0: eeprom at 50 { compatible = "atmel,24c02"; reg = <0x50>; pagesize = <16>;
board/dhelectronics/dh_stm32mp1/board.c +7 -8
@@ -78,22 +78,21 @@ DECLARE_GLOBAL_DATA_PTR;int setup_mac_address (void ) { -struct udevice *dev; -ofnode eeprom;unsigned char enetaddr[6 ]; -int ret; +struct udevice *dev; +int off, ret; ret =eth_env_get_enetaddr ("ethaddr" , enetaddr);if (ret)/* ethaddr is already set */ return 0 ; - eeprom =ofnode_path ("/soc/i2c at 5c002000/eeprom at 50" ); -if (!ofnode_valid (eeprom)) { -printf ("Invalid hardware path to EEPROM!\n" ); -return -ENODEV ; + off =fdt_path_offset (gd->fdt_blob,"eeprom0" ); +if (off <0 ) { +printf ("%s: No eeprom0 path offset\n" , __func__); +return off; } - ret =uclass_get_device_by_ofnode (UCLASS_I2C_EEPROM , eeprom, &dev); + ret =uclass_get_device_by_of_offset (UCLASS_I2C_EEPROM , off, &dev);if (ret) {printf ("Cannot find EEPROM!\n" );return ret;
Signature · 1 line
2.25.1
PATCH 1/1 ARM: dts: stm32: Use DT alias for the configuration EEPROM
Hi Marek
Quoted 61 lines · Marek Vasut
Use DT /aliases node to establish a stable phandle to the configuration EEPROM. This permits the configuration EEPROM to be moved e.g. to a different address or a different bus. Adjust the board code to handle new phandle lookup.
Signed-off-by Marek Vasut <[email protected]>Cc Patrick Delaunay <[email protected]>Cc Patrice Chotard <[email protected]>--- arch/arm/dts/stm32mp15xx-dhcom.dtsi | 6 +++++- board/dhelectronics/dh_stm32mp1/board.c | 15 +++++++-------- 2 files changed, 12 insertions(+), 9 deletions(-)arch/arm/dts/stm32mp15xx-dhcom.dtsi +5
-1@@ -10,6 +10,10 @@ #include <dt-bindings/mfd/st,stpmic1.h> / { + aliases { + eeprom0 = &eeprom0; + }; + memory at c0000000 { device_type = "memory"; reg = <0xC0000000 0x40000000>;@@ -187,7 +191,7 @@ }; }; - eeprom at 50 { + eeprom0: eeprom at 50 { compatible = "atmel,24c02"; reg = <0x50>; pagesize = <16>;board/dhelectronics/dh_stm32mp1/board.c +3
-7@@ -78,22 +78,21 @@ DECLARE_GLOBAL_DATA_PTR;int setup_mac_address (void ) { -struct udevice *dev; -ofnode eeprom;unsigned char enetaddr[6 ]; -int ret; +struct udevice *dev; +int off, ret; ret =eth_env_get_enetaddr ("ethaddr" , enetaddr);if (ret)/* ethaddr is already set */ return 0 ; - eeprom =ofnode_path ("/soc/i2c at 5c002000/eeprom at 50" ); -if (!ofnode_valid (eeprom)) { -printf ("Invalid hardware path to EEPROM!\n" ); -return -ENODEV ; + off =fdt_path_offset (gd->fdt_blob,"eeprom0" );
board/dhelectronics/dh_stm32mp1/board.c DECLARE_GLOBAL_DATA_PTR; · line 98
Quoted 10 lines
board/dhelectronics/dh_stm32mp1/board.c +4
-1+if (off <0 ) { +printf ("%s: No eeprom0 path offset\n" , __func__); +return off; } - ret =uclass_get_device_by_ofnode (UCLASS_I2C_EEPROM , eeprom, &dev); + ret =uclass_get_device_by_of_offset (UCLASS_I2C_EEPROM , off, &dev);if (ret) {printf ("Cannot find EEPROM!\n" );return ret;
Reviewed-by Patrice Chotard <[email protected]>
Thanks