Skip to contentSkip to conversation

HID: alps: Add AUI1657 device ID

PATCH In review Artem Borisov 4 participants 18 messages Apr 5, 2020 – Apr 16, 2020 2 messages not in the archive HID

lore
Share & tools
lore
#0 lore raw

PATCH 1/2 HID: alps: Add AUI1657 device ID

This device is used on Lenovo V130-15IKB variants and uses the same registers as U1.

---
 drivers/hid/hid-alps.c | 1 +
 drivers/hid/hid-ids.h  | 2 +-
 2 files changed, 2 insertions(+), 1 deletion(-)
drivers/hid/hid-alps.c +1 -0
index fa704153cb00..c2a2bd528890 100644
@@ -802,6 +802,7 @@ static int alps_probe(struct hid_device *hdev, const struct hid_device_id *id)
 		break;
 	case HID_DEVICE_ID_ALPS_U1_DUAL:
 	case HID_DEVICE_ID_ALPS_U1:
+	case HID_DEVICE_ID_ALPS_1657:
 		data->dev_type = U1;
 		break;
 	default:
drivers/hid/hid-ids.h +1 -1
index b18b13147a6f..324fddb37e27 100644
@@ -81,7 +81,7 @@
 #define HID_DEVICE_ID_ALPS_U1		0x1215
 #define HID_DEVICE_ID_ALPS_T4_BTNLESS	0x120C
 #define HID_DEVICE_ID_ALPS_1222		0x1222
-
+#define HID_DEVICE_ID_ALPS_1657         0x121E
 
 #define USB_VENDOR_ID_AMI		0x046b
 #define USB_DEVICE_ID_AMI_VIRT_KEYBOARD_AND_MOUSE	0xff10
Signature · 1 line
2.26.0
#1 lore raw

PATCH 2/2 HID: alps: Refactor axis resolution logic

AUI1657 doesn't follow the same logic for resolution calculation, since the resulting values are incorrect. Instead, it reports the actual resolution values in place of the pitch ones.
While we're at it, also refactor the whole resolution logic to make it more generic and sensible for multiple device support.

---
 drivers/hid/hid-alps.c | 41 +++++++++++++++++++++++++----------------
 1 file changed, 25 insertions(+), 16 deletions(-)
drivers/hid/hid-alps.c +25 -16
index c2a2bd528890..494c08cca645 100644
@@ -83,8 +83,8 @@ enum dev_num {
  * @max_fingers: total number of fingers
  * @has_sp: boolean of sp existense
  * @sp_btn_info: button information
- * @x_active_len_mm: active area length of X (mm)
- * @y_active_len_mm: active area length of Y (mm)
+ * @x_res: resolution of X
+ * @y_res: resolution of Y
  * @x_max: maximum x coordinate value
  * @y_max: maximum y coordinate value
  * @x_min: minimum x coordinate value
@@ -100,9 +100,10 @@ struct alps_dev {
 	enum dev_num dev_type;
 	u8  max_fingers;
 	u8  has_sp;
+	u8  no_pitch;
 	u8	sp_btn_info;
-	u32	x_active_len_mm;
-	u32	y_active_len_mm;
+	u32	x_res;
+	u32	y_res;
 	u32	x_max;
 	u32	y_max;
 	u32	x_min;
@@ -550,10 +551,6 @@ static int u1_init(struct hid_device *hdev, struct alps_dev *pri_data)
 		dev_err(&hdev->dev, "failed U1_RESO_DWN_ABS (%d)\n", ret);
 		goto exit;
 	}
-	pri_data->x_active_len_mm =
-		(pitch_x * (sen_line_num_x - 1)) / 10;
-	pri_data->y_active_len_mm =
-		(pitch_y * (sen_line_num_y - 1)) / 10;
 
 	pri_data->x_max =
 		(resolution << 2) * (sen_line_num_x - 1);
@@ -562,6 +559,18 @@ static int u1_init(struct hid_device *hdev, struct alps_dev *pri_data)
 		(resolution << 2) * (sen_line_num_y - 1);
 	pri_data->y_min = 1;
 
+	if (pri_data->no_pitch) {
+		pri_data->x_res = pitch_x;
+		pri_data->y_res = pitch_y;
+	} else {
+		pri_data->x_res =
+			(pri_data->x_max - 1) /
+			((pitch_x * (sen_line_num_x - 1)) / 10);
+		pri_data->y_res =
+			(pri_data->y_max - 1) /
+			((pitch_y * (sen_line_num_y - 1)) / 10);
+	}
+
 	ret = u1_read_write_register(hdev, ADDRESS_U1_PAD_BTN,
 			&tmp, 0, true);
 	if (ret < 0) {
@@ -622,7 +631,7 @@ static int T4_init(struct hid_device *hdev, struct alps_dev *pri_data)
 	pri_data->x_min = T4_COUNT_PER_ELECTRODE;
 	pri_data->y_max = sen_line_num_y * T4_COUNT_PER_ELECTRODE;
 	pri_data->y_min = T4_COUNT_PER_ELECTRODE;
-	pri_data->x_active_len_mm = pri_data->y_active_len_mm = 0;
+	pri_data->x_res = pri_data->y_res = 0;
 	pri_data->btn_cnt = 1;
 
 	ret = t4_read_write_register(hdev, PRM_SYS_CONFIG_1, &tmp, 0, true);
@@ -675,7 +684,7 @@ static int alps_input_configured(struct hid_device *hdev, struct hid_input *hi)
 	struct alps_dev *data = hid_get_drvdata(hdev);
 	struct input_dev *input = hi->input, *input2;
 	int ret;
-	int res_x, res_y, i;
+	int i;
 
 	data->input = input;
 
@@ -706,12 +715,9 @@ static int alps_input_configured(struct hid_device *hdev, struct hid_input *hi)
 	input_set_abs_params(input, ABS_MT_POSITION_Y,
 						data->y_min, data->y_max, 0, 0);
 
-	if (data->x_active_len_mm && data->y_active_len_mm) {
-		res_x = (data->x_max - 1) / data->x_active_len_mm;
-		res_y = (data->y_max - 1) / data->y_active_len_mm;
-
-		input_abs_set_res(input, ABS_MT_POSITION_X, res_x);
-		input_abs_set_res(input, ABS_MT_POSITION_Y, res_y);
+	if (data->x_res && data->y_res) {
+		input_abs_set_res(input, ABS_MT_POSITION_X, data->x_res);
+		input_abs_set_res(input, ABS_MT_POSITION_Y, data->y_res);
 	}
 
 	input_set_abs_params(input, ABS_MT_PRESSURE, 0, 64, 0, 0);
@@ -802,8 +808,11 @@ static int alps_probe(struct hid_device *hdev, const struct hid_device_id *id)
 		break;
 	case HID_DEVICE_ID_ALPS_U1_DUAL:
 	case HID_DEVICE_ID_ALPS_U1:
+		data->dev_type = U1;
+		break;
 	case HID_DEVICE_ID_ALPS_1657:
 		data->dev_type = U1;
+		data->no_pitch = 1;
 		break;
 	default:
 		data->dev_type = UNKNOWN;
Signature · 1 line
2.26.0
maintainer
#2 lore raw

Re: [PATCH 2/2] HID: alps: Refactor axis resolution logic

Quoted 5 lines · Artem Borisov

AUI1657 doesn't follow the same logic for resolution calculation, since the resulting values are incorrect. Instead, it reports the actual resolution values in place of the pitch ones.
While we're at it, also refactor the whole resolution logic to make it more generic and sensible for multiple device support.

Let's add Masaki Ota to ack this change if possible.

Would it be possible to be a little bit more verbose in the changelog, explaining *how* (or why) is the patch making the logic more generic and sensible?

Thanks!

Quoted 112 lines
---
 drivers/hid/hid-alps.c | 41 +++++++++++++++++++++++++----------------
 1 file changed, 25 insertions(+), 16 deletions(-)
drivers/hid/hid-alps.c +25 -16
index c2a2bd528890..494c08cca645 100644
@@ -83,8 +83,8 @@ enum dev_num {
  * @max_fingers: total number of fingers
  * @has_sp: boolean of sp existense
  * @sp_btn_info: button information
- * @x_active_len_mm: active area length of X (mm)
- * @y_active_len_mm: active area length of Y (mm)
+ * @x_res: resolution of X
+ * @y_res: resolution of Y
  * @x_max: maximum x coordinate value
  * @y_max: maximum y coordinate value
  * @x_min: minimum x coordinate value
@@ -100,9 +100,10 @@ struct alps_dev {
 	enum dev_num dev_type;
 	u8  max_fingers;
 	u8  has_sp;
+	u8  no_pitch;
 	u8	sp_btn_info;
-	u32	x_active_len_mm;
-	u32	y_active_len_mm;
+	u32	x_res;
+	u32	y_res;
 	u32	x_max;
 	u32	y_max;
 	u32	x_min;
@@ -550,10 +551,6 @@ static int u1_init(struct hid_device *hdev, struct alps_dev *pri_data)
 		dev_err(&hdev->dev, "failed U1_RESO_DWN_ABS (%d)\n", ret);
 		goto exit;
 	}
-	pri_data->x_active_len_mm =
-		(pitch_x * (sen_line_num_x - 1)) / 10;
-	pri_data->y_active_len_mm =
-		(pitch_y * (sen_line_num_y - 1)) / 10;
 
 	pri_data->x_max =
 		(resolution << 2) * (sen_line_num_x - 1);
@@ -562,6 +559,18 @@ static int u1_init(struct hid_device *hdev, struct alps_dev *pri_data)
 		(resolution << 2) * (sen_line_num_y - 1);
 	pri_data->y_min = 1;
 
+	if (pri_data->no_pitch) {
+		pri_data->x_res = pitch_x;
+		pri_data->y_res = pitch_y;
+	} else {
+		pri_data->x_res =
+			(pri_data->x_max - 1) /
+			((pitch_x * (sen_line_num_x - 1)) / 10);
+		pri_data->y_res =
+			(pri_data->y_max - 1) /
+			((pitch_y * (sen_line_num_y - 1)) / 10);
+	}
+
 	ret = u1_read_write_register(hdev, ADDRESS_U1_PAD_BTN,
 			&tmp, 0, true);
 	if (ret < 0) {
@@ -622,7 +631,7 @@ static int T4_init(struct hid_device *hdev, struct alps_dev *pri_data)
 	pri_data->x_min = T4_COUNT_PER_ELECTRODE;
 	pri_data->y_max = sen_line_num_y * T4_COUNT_PER_ELECTRODE;
 	pri_data->y_min = T4_COUNT_PER_ELECTRODE;
-	pri_data->x_active_len_mm = pri_data->y_active_len_mm = 0;
+	pri_data->x_res = pri_data->y_res = 0;
 	pri_data->btn_cnt = 1;
 
 	ret = t4_read_write_register(hdev, PRM_SYS_CONFIG_1, &tmp, 0, true);
@@ -675,7 +684,7 @@ static int alps_input_configured(struct hid_device *hdev, struct hid_input *hi)
 	struct alps_dev *data = hid_get_drvdata(hdev);
 	struct input_dev *input = hi->input, *input2;
 	int ret;
-	int res_x, res_y, i;
+	int i;
 
 	data->input = input;
 
@@ -706,12 +715,9 @@ static int alps_input_configured(struct hid_device *hdev, struct hid_input *hi)
 	input_set_abs_params(input, ABS_MT_POSITION_Y,
 						data->y_min, data->y_max, 0, 0);
 
-	if (data->x_active_len_mm && data->y_active_len_mm) {
-		res_x = (data->x_max - 1) / data->x_active_len_mm;
-		res_y = (data->y_max - 1) / data->y_active_len_mm;
-
-		input_abs_set_res(input, ABS_MT_POSITION_X, res_x);
-		input_abs_set_res(input, ABS_MT_POSITION_Y, res_y);
+	if (data->x_res && data->y_res) {
+		input_abs_set_res(input, ABS_MT_POSITION_X, data->x_res);
+		input_abs_set_res(input, ABS_MT_POSITION_Y, data->y_res);
 	}
 
 	input_set_abs_params(input, ABS_MT_PRESSURE, 0, 64, 0, 0);
@@ -802,8 +808,11 @@ static int alps_probe(struct hid_device *hdev, const struct hid_device_id *id)
 		break;
 	case HID_DEVICE_ID_ALPS_U1_DUAL:
 	case HID_DEVICE_ID_ALPS_U1:
+		data->dev_type = U1;
+		break;
 	case HID_DEVICE_ID_ALPS_1657:
 		data->dev_type = U1;
+		data->no_pitch = 1;
 		break;
 	default:
 		data->dev_type = UNKNOWN;
Signature · 1 line
2.26.0
Signature · 2 lines
Jiri Kosina
SUSE Labs
#3 lore raw

PATCH 2/2 HID: alps: Refactor axis resolution logic

AUI1657 doesn't follow the same logic for resolution calculation, since the resulting values are incorrect. Instead, it reports the actual resolution values in place of the pitch ones.
While we're at it, also refactor the whole resolution logic to make it more generic and sensible for multiple device support.

There are two main logical problems with the current code:
1. active_len_mm values are only used for resolution calculation on U1, yet are exposed globally as part of alps_dev structure.
2. The resolution calculation process happens in alps_input_configured, while everything else is calculated in u1_init function.

These problems become more apparent when we try to support a device that doesn't follow the same resolution calculation logic as U1. Since alps_input_configured is a device-agnostic function, we should avoid doing any measurements there and handle them in device-specific init functions like u1/T4_init instead.

To eliminate these problems we add global x_res and y_res values and populate them on a device-specific basis in the according init functions.

---
 drivers/hid/hid-alps.c | 41 +++++++++++++++++++++++++----------------
 1 file changed, 25 insertions(+), 16 deletions(-)
drivers/hid/hid-alps.c +25 -16
index c2a2bd528890..494c08cca645 100644
@@ -83,8 +83,8 @@ enum dev_num {
  * @max_fingers: total number of fingers
  * @has_sp: boolean of sp existense
  * @sp_btn_info: button information
- * @x_active_len_mm: active area length of X (mm)
- * @y_active_len_mm: active area length of Y (mm)
+ * @x_res: resolution of X
+ * @y_res: resolution of Y
  * @x_max: maximum x coordinate value
  * @y_max: maximum y coordinate value
  * @x_min: minimum x coordinate value
@@ -100,9 +100,10 @@ struct alps_dev {
 	enum dev_num dev_type;
 	u8  max_fingers;
 	u8  has_sp;
+	u8  no_pitch;
 	u8	sp_btn_info;
-	u32	x_active_len_mm;
-	u32	y_active_len_mm;
+	u32	x_res;
+	u32	y_res;
 	u32	x_max;
 	u32	y_max;
 	u32	x_min;
@@ -550,10 +551,6 @@ static int u1_init(struct hid_device *hdev, struct alps_dev *pri_data)
 		dev_err(&hdev->dev, "failed U1_RESO_DWN_ABS (%d)\n", ret);
 		goto exit;
 	}
-	pri_data->x_active_len_mm =
-		(pitch_x * (sen_line_num_x - 1)) / 10;
-	pri_data->y_active_len_mm =
-		(pitch_y * (sen_line_num_y - 1)) / 10;
 
 	pri_data->x_max =
 		(resolution << 2) * (sen_line_num_x - 1);
@@ -562,6 +559,18 @@ static int u1_init(struct hid_device *hdev, struct alps_dev *pri_data)
 		(resolution << 2) * (sen_line_num_y - 1);
 	pri_data->y_min = 1;
 
+	if (pri_data->no_pitch) {
+		pri_data->x_res = pitch_x;
+		pri_data->y_res = pitch_y;
+	} else {
+		pri_data->x_res =
+			(pri_data->x_max - 1) /
+			((pitch_x * (sen_line_num_x - 1)) / 10);
+		pri_data->y_res =
+			(pri_data->y_max - 1) /
+			((pitch_y * (sen_line_num_y - 1)) / 10);
+	}
+
 	ret = u1_read_write_register(hdev, ADDRESS_U1_PAD_BTN,
 			&tmp, 0, true);
 	if (ret < 0) {
@@ -622,7 +631,7 @@ static int T4_init(struct hid_device *hdev, struct alps_dev *pri_data)
 	pri_data->x_min = T4_COUNT_PER_ELECTRODE;
 	pri_data->y_max = sen_line_num_y * T4_COUNT_PER_ELECTRODE;
 	pri_data->y_min = T4_COUNT_PER_ELECTRODE;
-	pri_data->x_active_len_mm = pri_data->y_active_len_mm = 0;
+	pri_data->x_res = pri_data->y_res = 0;
 	pri_data->btn_cnt = 1;
 
 	ret = t4_read_write_register(hdev, PRM_SYS_CONFIG_1, &tmp, 0, true);
@@ -675,7 +684,7 @@ static int alps_input_configured(struct hid_device *hdev, struct hid_input *hi)
 	struct alps_dev *data = hid_get_drvdata(hdev);
 	struct input_dev *input = hi->input, *input2;
 	int ret;
-	int res_x, res_y, i;
+	int i;
 
 	data->input = input;
 
@@ -706,12 +715,9 @@ static int alps_input_configured(struct hid_device *hdev, struct hid_input *hi)
 	input_set_abs_params(input, ABS_MT_POSITION_Y,
 						data->y_min, data->y_max, 0, 0);
 
-	if (data->x_active_len_mm && data->y_active_len_mm) {
-		res_x = (data->x_max - 1) / data->x_active_len_mm;
-		res_y = (data->y_max - 1) / data->y_active_len_mm;
-
-		input_abs_set_res(input, ABS_MT_POSITION_X, res_x);
-		input_abs_set_res(input, ABS_MT_POSITION_Y, res_y);
+	if (data->x_res && data->y_res) {
+		input_abs_set_res(input, ABS_MT_POSITION_X, data->x_res);
+		input_abs_set_res(input, ABS_MT_POSITION_Y, data->y_res);
 	}
 
 	input_set_abs_params(input, ABS_MT_PRESSURE, 0, 64, 0, 0);
@@ -802,8 +808,11 @@ static int alps_probe(struct hid_device *hdev, const struct hid_device_id *id)
 		break;
 	case HID_DEVICE_ID_ALPS_U1_DUAL:
 	case HID_DEVICE_ID_ALPS_U1:
+		data->dev_type = U1;
+		break;
 	case HID_DEVICE_ID_ALPS_1657:
 		data->dev_type = U1;
+		data->no_pitch = 1;
 		break;
 	default:
 		data->dev_type = UNKNOWN;
Signature · 1 line
2.26.0
#4 lore raw

RE: [PATCH 2/2] HID: alps: Refactor axis resolution logic

Hi, Cao-san,

Do you know AUI1657 device? This device looks U1.
I think recent all U1 devices work as PTP.
Linux also supports PTP, so I think we should add something ID to Linux source code. (I remember a something flag is already exist.)

Best Regards,
Masaki Ota
-----Original Message-----
From: Artem Borisov <[email protected]>
Sent: Friday, April 10, 2020 8:00 AM
Cc: [email protected]; 太田 真喜 Masaki Ota <[email protected]>; Artem Borisov <[email protected]>; Benjamin Tissoires <[email protected]>; Henrik Rydberg <[email protected]>; [email protected]; [email protected]
Subject: [PATCH 2/2] HID: alps: Refactor axis resolution logic

AUI1657 doesn't follow the same logic for resolution calculation, since the resulting values are incorrect. Instead, it reports the actual resolution values in place of the pitch ones. While we're at it, also refactor the whole resolution logic to make it more generic and sensible for multiple device support.

There are two main logical problems with the current code:
1. active_len_mm values are only used for resolution calculation on U1, yet are exposed globally as part of alps_dev structure.
2. The resolution calculation process happens in alps_input_configured, while everything else is calculated in u1_init function.

These problems become more apparent when we try to support a device that doesn't follow the same resolution calculation logic as U1.
Since alps_input_configured is a device-agnostic function, we should avoid doing any measurements there and handle them in device-specific init functions like u1/T4_init instead.

To eliminate these problems we add global x_res and y_res values and populate them on a device-specific basis in the according init functions.

---
 drivers/hid/hid-alps.c | 41 +++++++++++++++++++++++++----------------
 1 file changed, 25 insertions(+), 16 deletions(-)
drivers/hid/hid-alps.c +5 -8
@@ -83,8 +83,8 @@ enum dev_num {
  * @max_fingers: total number of fingers
  * @has_sp: boolean of sp existense
  * @sp_btn_info: button information
- * @x_active_len_mm: active area length of X (mm)
- * @y_active_len_mm: active area length of Y (mm)
+ * @x_res: resolution of X
+ * @y_res: resolution of Y
  * @x_max: maximum x coordinate value
  * @y_max: maximum y coordinate value
  * @x_min: minimum x coordinate value
@@ -100,9 +100,10 @@ struct alps_dev {
 	enum dev_num dev_type;
 	u8  max_fingers;
 	u8  has_sp;
+	u8  no_pitch;
 	u8	sp_btn_info;
-	u32	x_active_len_mm;
-	u32	y_active_len_mm;
+	u32	x_res;
+	u32	y_res;
 	u32	x_max;
 	u32	y_max;
 	u32	x_min;
@@ -550,10 +551,6 @@ static int u1_init(struct hid_device *hdev, struct alps_dev *pri_data)
 		dev_err(&hdev->dev, "failed U1_RESO_DWN_ABS (%d)\n", ret);
 		goto exit;
 	}
-	pri_data->x_active_len_mm =
-		(pitch_x * (sen_line_num_x - 1)) / 10;
-	pri_data->y_active_len_mm =
-		(pitch_y * (sen_line_num_y - 1)) / 10;
 
 	pri_data->x_max =
 		(resolution << 2) * (sen_line_num_x - 1); @@ -562,6 +559,18 @@ static int u1_init(struct hid_device *hdev, struct alps_dev *pri_data)

(resolution << 2) * (sen_line_num_y - 1);
pri_data->y_min = 1;

+ if (pri_data->no_pitch) {
+ pri_data->x_res = pitch_x;
+ pri_data->y_res = pitch_y;
+ } else {
+ pri_data->x_res =
+ (pri_data->x_max - 1) /
+ ((pitch_x * (sen_line_num_x - 1)) / 10);
+ pri_data->y_res =
+ (pri_data->y_max - 1) /
+ ((pitch_y * (sen_line_num_y - 1)) / 10);
+ }
+
ret = u1_read_write_register(hdev, ADDRESS_U1_PAD_BTN,
&tmp, 0, true);
if (ret < 0) {
@@ -622,7 +631,7 @@ static int T4_init(struct hid_device *hdev, struct alps_dev *pri_data)
pri_data->x_min = T4_COUNT_PER_ELECTRODE;
pri_data->y_max = sen_line_num_y * T4_COUNT_PER_ELECTRODE; pri_data->y_min = T4_COUNT_PER_ELECTRODE;
- pri_data->x_active_len_mm = pri_data->y_active_len_mm = 0;
+ pri_data->x_res = pri_data->y_res = 0;
pri_data->btn_cnt = 1;

ret = t4_read_write_register(hdev, PRM_SYS_CONFIG_1, &tmp, 0, true); @@ -675,7 +684,7 @@ static int alps_input_configured(struct hid_device *hdev, struct hid_input *hi) struct alps_dev *data = hid_get_drvdata(hdev);
struct input_dev *input = hi->input, *input2;
int ret;
- int res_x, res_y, i;
+ int i;

data->input = input;

@@ -706,12 +715,9 @@ static int alps_input_configured(struct hid_device *hdev, struct hid_input *hi)
input_set_abs_params(input, ABS_MT_POSITION_Y,
data->y_min, data->y_max, 0, 0);

- if (data->x_active_len_mm && data->y_active_len_mm) {
- res_x = (data->x_max - 1) / data->x_active_len_mm;
- res_y = (data->y_max - 1) / data->y_active_len_mm;
-
- input_abs_set_res(input, ABS_MT_POSITION_X, res_x);
- input_abs_set_res(input, ABS_MT_POSITION_Y, res_y);
+ if (data->x_res && data->y_res) {
+ input_abs_set_res(input, ABS_MT_POSITION_X, data->x_res);
+ input_abs_set_res(input, ABS_MT_POSITION_Y, data->y_res);
}

input_set_abs_params(input, ABS_MT_PRESSURE, 0, 64, 0, 0); @@ -802,8 +808,11 @@ static int alps_probe(struct hid_device *hdev, const struct hid_device_id *id)
break;
case HID_DEVICE_ID_ALPS_U1_DUAL:
case HID_DEVICE_ID_ALPS_U1:
+ data->dev_type = U1;
+ break;
case HID_DEVICE_ID_ALPS_1657:
data->dev_type = U1;
+ data->no_pitch = 1;
break;
default:
data->dev_type = UNKNOWN;
--
2.26.0

maintainer
#5 lore raw

RE: [PATCH 2/2] HID: alps: Refactor axis resolution logic

Quoted 6 lines · Masaki Ota

Hi, Cao-san,

Do you know AUI1657 device? This device looks U1. I think recent all U1 devices work as PTP. Linux also supports PTP, so I think we should add something ID to Linux source code. (I remember a something flag is already exist.)

That's actually partially covered by Artem's 1/1 patch you have not been CCed on -- please see it here:

	http://lore.kernel.org/r/[email protected]

If this could be made more generic to cover a group of devices all-in-one, that'd be even better of course.

Thanks,

Signature · 2 lines
Jiri Kosina
SUSE Labs
#7 lore raw

RE: [PATCH 2/2] HID: alps: Refactor axis resolution logic

In reply to Masaki Ota

Hi Ota-san,

Thanks for your checking.
In fact, some of the U1 devices work as non-PTP.
AUI1657 is using U1(KGDBCHA004A) whose firmware just supports mouse mode and legacy mode.

Best Regards,
----------------------------------------------
Jason Cao(曹晓建)

-----Original Message-----
From: 太田 真喜 Masaki Ota <[email protected]>
Sent: Friday, April 10, 2020 8:29 AM
To: 曹 曉建 Xiaojian Cao <[email protected]>; Artem Borisov <[email protected]>
Cc: [email protected]; Benjamin Tissoires <[email protected]>; Henrik Rydberg <[email protected]>; [email protected]; [email protected]
Subject: RE: [PATCH 2/2] HID: alps: Refactor axis resolution logic

Hi, Cao-san,

Do you know AUI1657 device? This device looks U1.
I think recent all U1 devices work as PTP.
Linux also supports PTP, so I think we should add something ID to Linux source code. (I remember a something flag is already exist.)

Best Regards,
Masaki Ota
-----Original Message-----
From: Artem Borisov <[email protected]>
Sent: Friday, April 10, 2020 8:00 AM
Cc: [email protected]; 太田 真喜 Masaki Ota <[email protected]>; Artem Borisov <[email protected]>; Benjamin Tissoires <[email protected]>; Henrik Rydberg <[email protected]>; [email protected]; [email protected]
Subject: [PATCH 2/2] HID: alps: Refactor axis resolution logic

AUI1657 doesn't follow the same logic for resolution calculation, since the resulting values are incorrect. Instead, it reports the actual resolution values in place of the pitch ones. While we're at it, also refactor the whole resolution logic to make it more generic and sensible for multiple device support.

There are two main logical problems with the current code:
1. active_len_mm values are only used for resolution calculation on U1, yet are exposed globally as part of alps_dev structure.
2. The resolution calculation process happens in alps_input_configured, while everything else is calculated in u1_init function.

These problems become more apparent when we try to support a device that doesn't follow the same resolution calculation logic as U1.
Since alps_input_configured is a device-agnostic function, we should avoid doing any measurements there and handle them in device-specific init functions like u1/T4_init instead.

To eliminate these problems we add global x_res and y_res values and populate them on a device-specific basis in the according init functions.

---
 drivers/hid/hid-alps.c | 41 +++++++++++++++++++++++++----------------
 1 file changed, 25 insertions(+), 16 deletions(-)
drivers/hid/hid-alps.c +5 -8
@@ -83,8 +83,8 @@ enum dev_num {
  * @max_fingers: total number of fingers
  * @has_sp: boolean of sp existense
  * @sp_btn_info: button information
- * @x_active_len_mm: active area length of X (mm)
- * @y_active_len_mm: active area length of Y (mm)
+ * @x_res: resolution of X
+ * @y_res: resolution of Y
  * @x_max: maximum x coordinate value
  * @y_max: maximum y coordinate value
  * @x_min: minimum x coordinate value
@@ -100,9 +100,10 @@ struct alps_dev {
 	enum dev_num dev_type;
 	u8  max_fingers;
 	u8  has_sp;
+	u8  no_pitch;
 	u8	sp_btn_info;
-	u32	x_active_len_mm;
-	u32	y_active_len_mm;
+	u32	x_res;
+	u32	y_res;
 	u32	x_max;
 	u32	y_max;
 	u32	x_min;
@@ -550,10 +551,6 @@ static int u1_init(struct hid_device *hdev, struct alps_dev *pri_data)
 		dev_err(&hdev->dev, "failed U1_RESO_DWN_ABS (%d)\n", ret);
 		goto exit;
 	}
-	pri_data->x_active_len_mm =
-		(pitch_x * (sen_line_num_x - 1)) / 10;
-	pri_data->y_active_len_mm =
-		(pitch_y * (sen_line_num_y - 1)) / 10;
 
 	pri_data->x_max =
 		(resolution << 2) * (sen_line_num_x - 1); @@ -562,6 +559,18 @@ static int u1_init(struct hid_device *hdev, struct alps_dev *pri_data)

(resolution << 2) * (sen_line_num_y - 1);
pri_data->y_min = 1;

+ if (pri_data->no_pitch) {
+ pri_data->x_res = pitch_x;
+ pri_data->y_res = pitch_y;
+ } else {
+ pri_data->x_res =
+ (pri_data->x_max - 1) /
+ ((pitch_x * (sen_line_num_x - 1)) / 10);
+ pri_data->y_res =
+ (pri_data->y_max - 1) /
+ ((pitch_y * (sen_line_num_y - 1)) / 10);
+ }
+
ret = u1_read_write_register(hdev, ADDRESS_U1_PAD_BTN,
&tmp, 0, true);
if (ret < 0) {
@@ -622,7 +631,7 @@ static int T4_init(struct hid_device *hdev, struct alps_dev *pri_data)
pri_data->x_min = T4_COUNT_PER_ELECTRODE;
pri_data->y_max = sen_line_num_y * T4_COUNT_PER_ELECTRODE; pri_data->y_min = T4_COUNT_PER_ELECTRODE;
- pri_data->x_active_len_mm = pri_data->y_active_len_mm = 0;
+ pri_data->x_res = pri_data->y_res = 0;
pri_data->btn_cnt = 1;

ret = t4_read_write_register(hdev, PRM_SYS_CONFIG_1, &tmp, 0, true); @@ -675,7 +684,7 @@ static int alps_input_configured(struct hid_device *hdev, struct hid_input *hi) struct alps_dev *data = hid_get_drvdata(hdev);
struct input_dev *input = hi->input, *input2;
int ret;
- int res_x, res_y, i;
+ int i;

data->input = input;

@@ -706,12 +715,9 @@ static int alps_input_configured(struct hid_device *hdev, struct hid_input *hi)
input_set_abs_params(input, ABS_MT_POSITION_Y,
data->y_min, data->y_max, 0, 0);

- if (data->x_active_len_mm && data->y_active_len_mm) {
- res_x = (data->x_max - 1) / data->x_active_len_mm;
- res_y = (data->y_max - 1) / data->y_active_len_mm;
-
- input_abs_set_res(input, ABS_MT_POSITION_X, res_x);
- input_abs_set_res(input, ABS_MT_POSITION_Y, res_y);
+ if (data->x_res && data->y_res) {
+ input_abs_set_res(input, ABS_MT_POSITION_X, data->x_res);
+ input_abs_set_res(input, ABS_MT_POSITION_Y, data->y_res);
}

input_set_abs_params(input, ABS_MT_PRESSURE, 0, 64, 0, 0); @@ -802,8 +808,11 @@ static int alps_probe(struct hid_device *hdev, const struct hid_device_id *id)
break;
case HID_DEVICE_ID_ALPS_U1_DUAL:
case HID_DEVICE_ID_ALPS_U1:
+ data->dev_type = U1;
+ break;
case HID_DEVICE_ID_ALPS_1657:
data->dev_type = U1;
+ data->no_pitch = 1;
break;
default:
data->dev_type = UNKNOWN;
--
2.26.0

#8 lore raw

RE: [PATCH 2/2] HID: alps: Refactor axis resolution logic

Hi, Cao-san,

I got it. I also confirmed this touchpad is a special. What do you think this code modification?

Best Regards,
Masaki Ota
-----Original Message-----
From: 曹 曉建 Xiaojian Cao <[email protected]>
Sent: Friday, April 10, 2020 10:03 AM
To: 太田 真喜 Masaki Ota <[email protected]>; Artem Borisov <[email protected]>
Cc: [email protected]; Benjamin Tissoires <[email protected]>; Henrik Rydberg <[email protected]>; [email protected]; [email protected]
Subject: RE: [PATCH 2/2] HID: alps: Refactor axis resolution logic

Hi Ota-san,

Thanks for your checking.
In fact, some of the U1 devices work as non-PTP.
AUI1657 is using U1(KGDBCHA004A) whose firmware just supports mouse mode and legacy mode.

Best Regards,
----------------------------------------------
Jason Cao(曹晓建)

-----Original Message-----
From: 太田 真喜 Masaki Ota <[email protected]>
Sent: Friday, April 10, 2020 8:29 AM
To: 曹 曉建 Xiaojian Cao <[email protected]>; Artem Borisov <[email protected]>
Cc: [email protected]; Benjamin Tissoires <[email protected]>; Henrik Rydberg <[email protected]>; [email protected]; [email protected]
Subject: RE: [PATCH 2/2] HID: alps: Refactor axis resolution logic

Hi, Cao-san,

Do you know AUI1657 device? This device looks U1.
I think recent all U1 devices work as PTP.
Linux also supports PTP, so I think we should add something ID to Linux source code. (I remember a something flag is already exist.)

Best Regards,
Masaki Ota
-----Original Message-----
From: Artem Borisov <[email protected]>
Sent: Friday, April 10, 2020 8:00 AM
Cc: [email protected]; 太田 真喜 Masaki Ota <[email protected]>; Artem Borisov <[email protected]>; Benjamin Tissoires <[email protected]>; Henrik Rydberg <[email protected]>; [email protected]; [email protected]
Subject: [PATCH 2/2] HID: alps: Refactor axis resolution logic

AUI1657 doesn't follow the same logic for resolution calculation, since the resulting values are incorrect. Instead, it reports the actual resolution values in place of the pitch ones. While we're at it, also refactor the whole resolution logic to make it more generic and sensible for multiple device support.

There are two main logical problems with the current code:
1. active_len_mm values are only used for resolution calculation on U1, yet are exposed globally as part of alps_dev structure.
2. The resolution calculation process happens in alps_input_configured, while everything else is calculated in u1_init function.

These problems become more apparent when we try to support a device that doesn't follow the same resolution calculation logic as U1.
Since alps_input_configured is a device-agnostic function, we should avoid doing any measurements there and handle them in device-specific init functions like u1/T4_init instead.

To eliminate these problems we add global x_res and y_res values and populate them on a device-specific basis in the according init functions.

---
 drivers/hid/hid-alps.c | 41 +++++++++++++++++++++++++----------------
 1 file changed, 25 insertions(+), 16 deletions(-)
drivers/hid/hid-alps.c +5 -8
@@ -83,8 +83,8 @@ enum dev_num {
  * @max_fingers: total number of fingers
  * @has_sp: boolean of sp existense
  * @sp_btn_info: button information
- * @x_active_len_mm: active area length of X (mm)
- * @y_active_len_mm: active area length of Y (mm)
+ * @x_res: resolution of X
+ * @y_res: resolution of Y
  * @x_max: maximum x coordinate value
  * @y_max: maximum y coordinate value
  * @x_min: minimum x coordinate value
@@ -100,9 +100,10 @@ struct alps_dev {
 	enum dev_num dev_type;
 	u8  max_fingers;
 	u8  has_sp;
+	u8  no_pitch;
 	u8	sp_btn_info;
-	u32	x_active_len_mm;
-	u32	y_active_len_mm;
+	u32	x_res;
+	u32	y_res;
 	u32	x_max;
 	u32	y_max;
 	u32	x_min;
@@ -550,10 +551,6 @@ static int u1_init(struct hid_device *hdev, struct alps_dev *pri_data)
 		dev_err(&hdev->dev, "failed U1_RESO_DWN_ABS (%d)\n", ret);
 		goto exit;
 	}
-	pri_data->x_active_len_mm =
-		(pitch_x * (sen_line_num_x - 1)) / 10;
-	pri_data->y_active_len_mm =
-		(pitch_y * (sen_line_num_y - 1)) / 10;
 
 	pri_data->x_max =
 		(resolution << 2) * (sen_line_num_x - 1); @@ -562,6 +559,18 @@ static int u1_init(struct hid_device *hdev, struct alps_dev *pri_data)

(resolution << 2) * (sen_line_num_y - 1);
pri_data->y_min = 1;

+ if (pri_data->no_pitch) {
+ pri_data->x_res = pitch_x;
+ pri_data->y_res = pitch_y;
+ } else {
+ pri_data->x_res =
+ (pri_data->x_max - 1) /
+ ((pitch_x * (sen_line_num_x - 1)) / 10);
+ pri_data->y_res =
+ (pri_data->y_max - 1) /
+ ((pitch_y * (sen_line_num_y - 1)) / 10);
+ }
+
ret = u1_read_write_register(hdev, ADDRESS_U1_PAD_BTN,
&tmp, 0, true);
if (ret < 0) {
@@ -622,7 +631,7 @@ static int T4_init(struct hid_device *hdev, struct alps_dev *pri_data)
pri_data->x_min = T4_COUNT_PER_ELECTRODE;
pri_data->y_max = sen_line_num_y * T4_COUNT_PER_ELECTRODE; pri_data->y_min = T4_COUNT_PER_ELECTRODE;
- pri_data->x_active_len_mm = pri_data->y_active_len_mm = 0;
+ pri_data->x_res = pri_data->y_res = 0;
pri_data->btn_cnt = 1;

ret = t4_read_write_register(hdev, PRM_SYS_CONFIG_1, &tmp, 0, true); @@ -675,7 +684,7 @@ static int alps_input_configured(struct hid_device *hdev, struct hid_input *hi) struct alps_dev *data = hid_get_drvdata(hdev);
struct input_dev *input = hi->input, *input2;
int ret;
- int res_x, res_y, i;
+ int i;

data->input = input;

@@ -706,12 +715,9 @@ static int alps_input_configured(struct hid_device *hdev, struct hid_input *hi)
input_set_abs_params(input, ABS_MT_POSITION_Y,
data->y_min, data->y_max, 0, 0);

- if (data->x_active_len_mm && data->y_active_len_mm) {
- res_x = (data->x_max - 1) / data->x_active_len_mm;
- res_y = (data->y_max - 1) / data->y_active_len_mm;
-
- input_abs_set_res(input, ABS_MT_POSITION_X, res_x);
- input_abs_set_res(input, ABS_MT_POSITION_Y, res_y);
+ if (data->x_res && data->y_res) {
+ input_abs_set_res(input, ABS_MT_POSITION_X, data->x_res);
+ input_abs_set_res(input, ABS_MT_POSITION_Y, data->y_res);
}

input_set_abs_params(input, ABS_MT_PRESSURE, 0, 64, 0, 0); @@ -802,8 +808,11 @@ static int alps_probe(struct hid_device *hdev, const struct hid_device_id *id)
break;
case HID_DEVICE_ID_ALPS_U1_DUAL:
case HID_DEVICE_ID_ALPS_U1:
+ data->dev_type = U1;
+ break;
case HID_DEVICE_ID_ALPS_1657:
data->dev_type = U1;
+ data->no_pitch = 1;
break;
default:
data->dev_type = UNKNOWN;
--
2.26.0

#6 lore raw

RE: [PATCH 2/2] HID: alps: Refactor axis resolution logic

In reply to Jiri Kosina

Hi Jiri-san,

Thanks for your information. I will look into it.

Best Regards,
----------------------------------------------
Jason Cao(曹晓建)

-----Original Message-----
From: Jiri Kosina <[email protected]>
Sent: Friday, April 10, 2020 8:47 AM
To: 太田 真喜 Masaki Ota <[email protected]>
Cc: 曹 曉建 Xiaojian Cao <[email protected]>; Artem Borisov <[email protected]>; Benjamin Tissoires <[email protected]>; Henrik Rydberg <[email protected]>; [email protected]; [email protected]
Subject: RE: [PATCH 2/2] HID: alps: Refactor axis resolution logic

Quoted 6 lines · Masaki Ota

Hi, Cao-san,

Do you know AUI1657 device? This device looks U1. I think recent all U1 devices work as PTP. Linux also supports PTP, so I think we should add something ID to Linux source code. (I remember a something flag is already exist.)

That's actually partially covered by Artem's 1/1 patch you have not been CCed on -- please see it here:

	http://lore.kernel.org/r/[email protected]

If this could be made more generic to cover a group of devices all-in-one, that'd be even better of course.

Thanks,

--
Jiri Kosina
SUSE Labs

#9 lore raw

RE: [PATCH 2/2] HID: alps: Refactor axis resolution logic

In reply to Masaki Ota

Hi Ota-san,

I need to study the background first, then I will update my understanding about it.

Best Regards,
----------------------------------------------
Jason Cao(曹晓建)

-----Original Message-----
From: 太田 真喜 Masaki Ota <[email protected]>
Sent: Friday, April 10, 2020 9:51 AM
To: 曹 曉建 Xiaojian Cao <[email protected]>; Artem Borisov <[email protected]>
Cc: [email protected]; Benjamin Tissoires <[email protected]>; Henrik Rydberg <[email protected]>; [email protected]; [email protected]
Subject: RE: [PATCH 2/2] HID: alps: Refactor axis resolution logic

Hi, Cao-san,

I got it. I also confirmed this touchpad is a special. What do you think this code modification?

Best Regards,
Masaki Ota
-----Original Message-----
From: 曹 曉建 Xiaojian Cao <[email protected]>
Sent: Friday, April 10, 2020 10:03 AM
To: 太田 真喜 Masaki Ota <[email protected]>; Artem Borisov <[email protected]>
Cc: [email protected]; Benjamin Tissoires <[email protected]>; Henrik Rydberg <[email protected]>; [email protected]; [email protected]
Subject: RE: [PATCH 2/2] HID: alps: Refactor axis resolution logic

Hi Ota-san,

Thanks for your checking.
In fact, some of the U1 devices work as non-PTP.
AUI1657 is using U1(KGDBCHA004A) whose firmware just supports mouse mode and legacy mode.

Best Regards,
----------------------------------------------
Jason Cao(曹晓建)

-----Original Message-----
From: 太田 真喜 Masaki Ota <[email protected]>
Sent: Friday, April 10, 2020 8:29 AM
To: 曹 曉建 Xiaojian Cao <[email protected]>; Artem Borisov <[email protected]>
Cc: [email protected]; Benjamin Tissoires <[email protected]>; Henrik Rydberg <[email protected]>; [email protected]; [email protected]
Subject: RE: [PATCH 2/2] HID: alps: Refactor axis resolution logic

Hi, Cao-san,

Do you know AUI1657 device? This device looks U1.
I think recent all U1 devices work as PTP.
Linux also supports PTP, so I think we should add something ID to Linux source code. (I remember a something flag is already exist.)

Best Regards,
Masaki Ota
-----Original Message-----
From: Artem Borisov <[email protected]>
Sent: Friday, April 10, 2020 8:00 AM
Cc: [email protected]; 太田 真喜 Masaki Ota <[email protected]>; Artem Borisov <[email protected]>; Benjamin Tissoires <[email protected]>; Henrik Rydberg <[email protected]>; [email protected]; [email protected]
Subject: [PATCH 2/2] HID: alps: Refactor axis resolution logic

AUI1657 doesn't follow the same logic for resolution calculation, since the resulting values are incorrect. Instead, it reports the actual resolution values in place of the pitch ones. While we're at it, also refactor the whole resolution logic to make it more generic and sensible for multiple device support.

There are two main logical problems with the current code:
1. active_len_mm values are only used for resolution calculation on U1, yet are exposed globally as part of alps_dev structure.
2. The resolution calculation process happens in alps_input_configured, while everything else is calculated in u1_init function.

These problems become more apparent when we try to support a device that doesn't follow the same resolution calculation logic as U1.
Since alps_input_configured is a device-agnostic function, we should avoid doing any measurements there and handle them in device-specific init functions like u1/T4_init instead.

To eliminate these problems we add global x_res and y_res values and populate them on a device-specific basis in the according init functions.

---
 drivers/hid/hid-alps.c | 41 +++++++++++++++++++++++++----------------
 1 file changed, 25 insertions(+), 16 deletions(-)
drivers/hid/hid-alps.c +5 -8
@@ -83,8 +83,8 @@ enum dev_num {
  * @max_fingers: total number of fingers
  * @has_sp: boolean of sp existense
  * @sp_btn_info: button information
- * @x_active_len_mm: active area length of X (mm)
- * @y_active_len_mm: active area length of Y (mm)
+ * @x_res: resolution of X
+ * @y_res: resolution of Y
  * @x_max: maximum x coordinate value
  * @y_max: maximum y coordinate value
  * @x_min: minimum x coordinate value
@@ -100,9 +100,10 @@ struct alps_dev {
 	enum dev_num dev_type;
 	u8  max_fingers;
 	u8  has_sp;
+	u8  no_pitch;
 	u8	sp_btn_info;
-	u32	x_active_len_mm;
-	u32	y_active_len_mm;
+	u32	x_res;
+	u32	y_res;
 	u32	x_max;
 	u32	y_max;
 	u32	x_min;
@@ -550,10 +551,6 @@ static int u1_init(struct hid_device *hdev, struct alps_dev *pri_data)
 		dev_err(&hdev->dev, "failed U1_RESO_DWN_ABS (%d)\n", ret);
 		goto exit;
 	}
-	pri_data->x_active_len_mm =
-		(pitch_x * (sen_line_num_x - 1)) / 10;
-	pri_data->y_active_len_mm =
-		(pitch_y * (sen_line_num_y - 1)) / 10;
 
 	pri_data->x_max =
 		(resolution << 2) * (sen_line_num_x - 1); @@ -562,6 +559,18 @@ static int u1_init(struct hid_device *hdev, struct alps_dev *pri_data)

(resolution << 2) * (sen_line_num_y - 1);
pri_data->y_min = 1;

+ if (pri_data->no_pitch) {
+ pri_data->x_res = pitch_x;
+ pri_data->y_res = pitch_y;
+ } else {
+ pri_data->x_res =
+ (pri_data->x_max - 1) /
+ ((pitch_x * (sen_line_num_x - 1)) / 10);
+ pri_data->y_res =
+ (pri_data->y_max - 1) /
+ ((pitch_y * (sen_line_num_y - 1)) / 10);
+ }
+
ret = u1_read_write_register(hdev, ADDRESS_U1_PAD_BTN,
&tmp, 0, true);
if (ret < 0) {
@@ -622,7 +631,7 @@ static int T4_init(struct hid_device *hdev, struct alps_dev *pri_data)
pri_data->x_min = T4_COUNT_PER_ELECTRODE;
pri_data->y_max = sen_line_num_y * T4_COUNT_PER_ELECTRODE; pri_data->y_min = T4_COUNT_PER_ELECTRODE;
- pri_data->x_active_len_mm = pri_data->y_active_len_mm = 0;
+ pri_data->x_res = pri_data->y_res = 0;
pri_data->btn_cnt = 1;

ret = t4_read_write_register(hdev, PRM_SYS_CONFIG_1, &tmp, 0, true); @@ -675,7 +684,7 @@ static int alps_input_configured(struct hid_device *hdev, struct hid_input *hi) struct alps_dev *data = hid_get_drvdata(hdev);
struct input_dev *input = hi->input, *input2;
int ret;
- int res_x, res_y, i;
+ int i;

data->input = input;

@@ -706,12 +715,9 @@ static int alps_input_configured(struct hid_device *hdev, struct hid_input *hi)
input_set_abs_params(input, ABS_MT_POSITION_Y,
data->y_min, data->y_max, 0, 0);

- if (data->x_active_len_mm && data->y_active_len_mm) {
- res_x = (data->x_max - 1) / data->x_active_len_mm;
- res_y = (data->y_max - 1) / data->y_active_len_mm;
-
- input_abs_set_res(input, ABS_MT_POSITION_X, res_x);
- input_abs_set_res(input, ABS_MT_POSITION_Y, res_y);
+ if (data->x_res && data->y_res) {
+ input_abs_set_res(input, ABS_MT_POSITION_X, data->x_res);
+ input_abs_set_res(input, ABS_MT_POSITION_Y, data->y_res);
}

input_set_abs_params(input, ABS_MT_PRESSURE, 0, 64, 0, 0); @@ -802,8 +808,11 @@ static int alps_probe(struct hid_device *hdev, const struct hid_device_id *id)
break;
case HID_DEVICE_ID_ALPS_U1_DUAL:
case HID_DEVICE_ID_ALPS_U1:
+ data->dev_type = U1;
+ break;
case HID_DEVICE_ID_ALPS_1657:
data->dev_type = U1;
+ data->no_pitch = 1;
break;
default:
data->dev_type = UNKNOWN;
--
2.26.0

maintainer
#19 lore raw
In reply to Artem Borisov
Quoted 4 lines · Artem Borisov

This device is used on Lenovo V130-15IKB variants and uses the same registers as U1.

I am in the meantime applying this one, and postponing the axis resolution logic followup, waiting for Alps people to grok it.

Thanks,

Signature · 2 lines
Jiri Kosina
SUSE Labs
#12 lore raw

Re: [PATCH 2/2] HID: alps: Refactor axis resolution logic

In reply to a message not in the archive

Hi.

I can't quite understand your objections.
1. Do you mean that we can't use AUI1657 because there are already drivers which do that (and I'm sure there are not) or that there are more devices using 0x121E?
2. The second instance of product ID is not used anywhere in the code at least for U1 so I didn't see any point to add another unused value that replicates the previous one.
3. I obviously don't have any internal documentation to argue with that, but you have mentioned above that aui1657 is just another panel based on U1, Apart from that, the touchpad is fully functional with the current code submitted which wouldn't make any sense if the report IDs were wrong.

I'm running Arch with 5.6.3 kernel, though I'm not sure how that information will be relevant to the patch.

Thanks.

ср, 15 апр. 2020 г. в 10:47, Xiaojian Cao <[email protected]>:

Quoted 231 lines

Hi Artem,

We’ve reviewed your modifications, and already found some problems as below:

It’s not suitable to use HWID AUI1657 in the source code, we because there are many projects using the same touchpad. It will confuse the coder in the future.

There are 2 places that maintain the Product ID/Device ID in the mainstream driver, currently your modifications just maintained one of them.

If we need to support the new Product ID/Device ID, then the report IDs will also be modified. Alps Alpine have different report ID list for different products.

BTW, what is your OS version and what’s its Linux kernel version?

Thank you.

Best Regards,

----------------------------------------------

Jason Cao(曹晓建)

From: Artem Borisov <[email protected]>
Sent: Wednesday, April 15, 2020 1:51 AM
To: 曹 曉建 Xiaojian Cao <[email protected]>
Cc: 太田 真喜 Masaki Ota <[email protected]>; [email protected]; Benjamin Tissoires <[email protected]>; Henrik Rydberg <[email protected]>; [email protected]; [email protected]; 野村 哲哉 Tetsuya Nomura <[email protected]>; Vadim Klishko <[email protected]>; #ALCHT_ML_POD_CN <[email protected]>
Subject: Re: [PATCH 2/2] HID: alps: Refactor axis resolution logic

Any updates on that yet?

пт, 10 апр. 2020 г., 06:28 Xiaojian Cao <[email protected]>:

Hi Ota-san,

I need to study the background first, then I will update my understanding about it.

Best Regards,
----------------------------------------------
Jason Cao(曹晓建)

-----Original Message-----
From: 太田 真喜 Masaki Ota <[email protected]>
Sent: Friday, April 10, 2020 9:51 AM
To: 曹 曉建 Xiaojian Cao <[email protected]>; Artem Borisov <[email protected]>
Cc: [email protected]; Benjamin Tissoires <[email protected]>; Henrik Rydberg <[email protected]>; [email protected]; [email protected]
Subject: RE: [PATCH 2/2] HID: alps: Refactor axis resolution logic

Hi, Cao-san,

I got it. I also confirmed this touchpad is a special. What do you think this code modification?

Best Regards,
Masaki Ota
-----Original Message-----
From: 曹 曉建 Xiaojian Cao <[email protected]>
Sent: Friday, April 10, 2020 10:03 AM
To: 太田 真喜 Masaki Ota <[email protected]>; Artem Borisov <[email protected]>
Cc: [email protected]; Benjamin Tissoires <[email protected]>; Henrik Rydberg <[email protected]>; [email protected]; [email protected]
Subject: RE: [PATCH 2/2] HID: alps: Refactor axis resolution logic

Hi Ota-san,

Thanks for your checking.
In fact, some of the U1 devices work as non-PTP.
AUI1657 is using U1(KGDBCHA004A) whose firmware just supports mouse mode and legacy mode.

Best Regards,
----------------------------------------------
Jason Cao(曹晓建)

-----Original Message-----
From: 太田 真喜 Masaki Ota <[email protected]>
Sent: Friday, April 10, 2020 8:29 AM
To: 曹 曉建 Xiaojian Cao <[email protected]>; Artem Borisov <[email protected]>
Cc: [email protected]; Benjamin Tissoires <[email protected]>; Henrik Rydberg <[email protected]>; [email protected]; [email protected]
Subject: RE: [PATCH 2/2] HID: alps: Refactor axis resolution logic

Hi, Cao-san,

Do you know AUI1657 device? This device looks U1.
I think recent all U1 devices work as PTP.
Linux also supports PTP, so I think we should add something ID to Linux source code. (I remember a something flag is already exist.)

Best Regards,
Masaki Ota
-----Original Message-----
From: Artem Borisov <[email protected]>
Sent: Friday, April 10, 2020 8:00 AM
Cc: [email protected]; 太田 真喜 Masaki Ota <[email protected]>; Artem Borisov <[email protected]>; Benjamin Tissoires <[email protected]>; Henrik Rydberg <[email protected]>; [email protected]; [email protected]
Subject: [PATCH 2/2] HID: alps: Refactor axis resolution logic

AUI1657 doesn't follow the same logic for resolution calculation, since the resulting values are incorrect. Instead, it reports the actual resolution values in place of the pitch ones. While we're at it, also refactor the whole resolution logic to make it more generic and sensible for multiple device support.

There are two main logical problems with the current code:
1. active_len_mm values are only used for resolution calculation on U1, yet are exposed globally as part of alps_dev structure.
2. The resolution calculation process happens in alps_input_configured, while everything else is calculated in u1_init function.

These problems become more apparent when we try to support a device that doesn't follow the same resolution calculation logic as U1.
Since alps_input_configured is a device-agnostic function, we should avoid doing any measurements there and handle them in device-specific init functions like u1/T4_init instead.

To eliminate these problems we add global x_res and y_res values and populate them on a device-specific basis in the according init functions.

---
 drivers/hid/hid-alps.c | 41 +++++++++++++++++++++++++----------------
 1 file changed, 25 insertions(+), 16 deletions(-)
drivers/hid/hid-alps.c +5 -8
@@ -83,8 +83,8 @@ enum dev_num {
  * @max_fingers: total number of fingers
  * @has_sp: boolean of sp existense
  * @sp_btn_info: button information
- * @x_active_len_mm: active area length of X (mm)
- * @y_active_len_mm: active area length of Y (mm)
+ * @x_res: resolution of X
+ * @y_res: resolution of Y
  * @x_max: maximum x coordinate value
  * @y_max: maximum y coordinate value
  * @x_min: minimum x coordinate value
@@ -100,9 +100,10 @@ struct alps_dev {
        enum dev_num dev_type;
        u8  max_fingers;
        u8  has_sp;
+       u8  no_pitch;
        u8      sp_btn_info;
-       u32     x_active_len_mm;
-       u32     y_active_len_mm;
+       u32     x_res;
+       u32     y_res;
        u32     x_max;
        u32     y_max;
        u32     x_min;
@@ -550,10 +551,6 @@ static int u1_init(struct hid_device *hdev, struct alps_dev *pri_data)
                dev_err(&hdev->dev, "failed U1_RESO_DWN_ABS (%d)\n", ret);
                goto exit;
        }
-       pri_data->x_active_len_mm =
-               (pitch_x * (sen_line_num_x - 1)) / 10;
-       pri_data->y_active_len_mm =
-               (pitch_y * (sen_line_num_y - 1)) / 10;
 
        pri_data->x_max =
                (resolution << 2) * (sen_line_num_x - 1); @@ -562,6 +559,18 @@ static int u1_init(struct hid_device *hdev, struct alps_dev *pri_data)
                (resolution << 2) * (sen_line_num_y - 1);
        pri_data->y_min = 1;
drivers/hid/hid-alps.c +13 -1
+       if (pri_data->no_pitch) {
+               pri_data->x_res = pitch_x;
+               pri_data->y_res = pitch_y;
+       } else {
+               pri_data->x_res =
+                       (pri_data->x_max - 1) /
+                       ((pitch_x * (sen_line_num_x - 1)) / 10);
+               pri_data->y_res =
+                       (pri_data->y_max - 1) /
+                       ((pitch_y * (sen_line_num_y - 1)) / 10);
+       }
+
        ret = u1_read_write_register(hdev, ADDRESS_U1_PAD_BTN,
                        &tmp, 0, true);
        if (ret < 0) {
@@ -622,7 +631,7 @@ static int T4_init(struct hid_device *hdev, struct alps_dev *pri_data)
        pri_data->x_min = T4_COUNT_PER_ELECTRODE;
        pri_data->y_max = sen_line_num_y * T4_COUNT_PER_ELECTRODE;
        pri_data->y_min = T4_COUNT_PER_ELECTRODE;
-       pri_data->x_active_len_mm = pri_data->y_active_len_mm = 0;
+       pri_data->x_res = pri_data->y_res = 0;
        pri_data->btn_cnt = 1;
 
        ret = t4_read_write_register(hdev, PRM_SYS_CONFIG_1, &tmp, 0, true); @@ -675,7 +684,7 @@ static int alps_input_configured(struct hid_device *hdev, struct hid_input *hi)
        struct alps_dev *data = hid_get_drvdata(hdev);
        struct input_dev *input = hi->input, *input2;
        int ret;
drivers/hid/hid-alps.c +4 -7
-       int res_x, res_y, i;
+       int i;
 
        data->input = input;
@@ -706,12 +715,9 @@ static int alps_input_configured(struct hid_device *hdev, struct hid_input *hi)
        input_set_abs_params(input, ABS_MT_POSITION_Y,
                                                data->y_min, data->y_max, 0, 0);
 
-       if (data->x_active_len_mm && data->y_active_len_mm) {
-               res_x = (data->x_max - 1) / data->x_active_len_mm;
-               res_y = (data->y_max - 1) / data->y_active_len_mm;
-
-               input_abs_set_res(input, ABS_MT_POSITION_X, res_x);
-               input_abs_set_res(input, ABS_MT_POSITION_Y, res_y);
+       if (data->x_res && data->y_res) {
+               input_abs_set_res(input, ABS_MT_POSITION_X, data->x_res);
+               input_abs_set_res(input, ABS_MT_POSITION_Y, data->y_res);
        }
 
        input_set_abs_params(input, ABS_MT_PRESSURE, 0, 64, 0, 0); @@ -802,8 +808,11 @@ static int alps_probe(struct hid_device *hdev, const struct hid_device_id *id)
                break;
        case HID_DEVICE_ID_ALPS_U1_DUAL:
        case HID_DEVICE_ID_ALPS_U1:
drivers/hid/hid-alps.c +3 -1
+               data->dev_type = U1;
+               break;
        case HID_DEVICE_ID_ALPS_1657:
                data->dev_type = U1;
+               data->no_pitch = 1;
                break;
        default:
                data->dev_type = UNKNOWN;
--

2.26.0

#13 lore raw

RE: [PATCH 2/2] HID: alps: Refactor axis resolution logic

Hi Artem,

Thanks for your checking, my feedbacks are as below:
1.It is about the coding style that we should not use HWID in the string "HID_DEVICE_ID_ALPS_1657", there are a large number of HWIDs using this touchpad. We should use the device type information in this string, such as "U1_UNICORN_LEGACY". 2.This is also about the coding style, we'd better make sure they are the same with each other, or just leave one list there.
3.If we'd like to upgrade the mainstream driver for only this project, then it works, but for the other projects, it has problems. If there is enough time, we'd like to prepare a better patch for most of our products.

Thank you for sharing the kernel version. I think, the review result would not be reliable if we don't have the correct source code of your kernel version.

Best Regards,
----------------------------------------------
Jason Cao(曹晓建)

-----Original Message-----
From: Artem Borisov <[email protected]>
Sent: Wednesday, April 15, 2020 5:16 PM
To: 曹 曉建 Xiaojian Cao <[email protected]>
Cc: 太田 真喜 Masaki Ota <[email protected]>; [email protected]; Benjamin Tissoires <[email protected]>; Henrik Rydberg <[email protected]>; [email protected]; [email protected]; 野村 哲哉 Tetsuya Nomura <[email protected]>; Vadim Klishko <[email protected]>; #ALCHT_ML_POD_CN <[email protected]>
Subject: Re: [PATCH 2/2] HID: alps: Refactor axis resolution logic

Hi.

I can't quite understand your objections.
1. Do you mean that we can't use AUI1657 because there are already drivers which do that (and I'm sure there are not) or that there are more devices using 0x121E?
2. The second instance of product ID is not used anywhere in the code at least for U1 so I didn't see any point to add another unused value that replicates the previous one.
3. I obviously don't have any internal documentation to argue with that, but you have mentioned above that aui1657 is just another panel based on U1, Apart from that, the touchpad is fully functional with the current code submitted which wouldn't make any sense if the report IDs were wrong.

I'm running Arch with 5.6.3 kernel, though I'm not sure how that information will be relevant to the patch.

Thanks.

ср, 15 апр. 2020 г. в 10:47, Xiaojian Cao <[email protected]>:

Quoted 252 lines

Hi Artem,

We’ve reviewed your modifications, and already found some problems as below:

It’s not suitable to use HWID AUI1657 in the source code, we because there are many projects using the same touchpad. It will confuse the coder in the future.

There are 2 places that maintain the Product ID/Device ID in the mainstream driver, currently your modifications just maintained one of them.

If we need to support the new Product ID/Device ID, then the report IDs will also be modified. Alps Alpine have different report ID list for different products.

BTW, what is your OS version and what’s its Linux kernel version?

Thank you.

Best Regards,

----------------------------------------------

Jason Cao(曹晓建)

From: Artem Borisov <[email protected]>
Sent: Wednesday, April 15, 2020 1:51 AM
To: 曹 曉建 Xiaojian Cao <[email protected]>
Cc: 太田 真喜 Masaki Ota <[email protected]>; [email protected]; Benjamin Tissoires <[email protected]>; Henrik Rydberg <[email protected]>; [email protected]; [email protected]; 野村 哲哉 Tetsuya Nomura <[email protected]>; Vadim Klishko <[email protected]>; #ALCHT_ML_POD_CN <[email protected]>
Subject: Re: [PATCH 2/2] HID: alps: Refactor axis resolution logic

Any updates on that yet?

пт, 10 апр. 2020 г., 06:28 Xiaojian Cao <[email protected]>:

Hi Ota-san,

I need to study the background first, then I will update my understanding about it.

Best Regards,
----------------------------------------------
Jason Cao(曹晓建)

-----Original Message-----
From: 太田 真喜 Masaki Ota <[email protected]>
Sent: Friday, April 10, 2020 9:51 AM
To: 曹 曉建 Xiaojian Cao <[email protected]>; Artem Borisov <[email protected]>
Cc: [email protected]; Benjamin Tissoires <[email protected]>; Henrik Rydberg <[email protected]>; [email protected]; [email protected]
Subject: RE: [PATCH 2/2] HID: alps: Refactor axis resolution logic

Hi, Cao-san,

I got it. I also confirmed this touchpad is a special. What do you think this code modification?

Best Regards,
Masaki Ota
-----Original Message-----
From: 曹 曉建 Xiaojian Cao <[email protected]>
Sent: Friday, April 10, 2020 10:03 AM
To: 太田 真喜 Masaki Ota <[email protected]>; Artem Borisov <[email protected]>
Cc: [email protected]; Benjamin Tissoires <[email protected]>; Henrik Rydberg <[email protected]>; [email protected]; [email protected]
Subject: RE: [PATCH 2/2] HID: alps: Refactor axis resolution logic

Hi Ota-san,

Thanks for your checking.
In fact, some of the U1 devices work as non-PTP.
AUI1657 is using U1(KGDBCHA004A) whose firmware just supports mouse mode and legacy mode.

Best Regards,
----------------------------------------------
Jason Cao(曹晓建)

-----Original Message-----
From: 太田 真喜 Masaki Ota <[email protected]>
Sent: Friday, April 10, 2020 8:29 AM
To: 曹 曉建 Xiaojian Cao <[email protected]>; Artem Borisov <[email protected]>
Cc: [email protected]; Benjamin Tissoires <[email protected]>; Henrik Rydberg <[email protected]>; [email protected]; [email protected]
Subject: RE: [PATCH 2/2] HID: alps: Refactor axis resolution logic

Hi, Cao-san,

Do you know AUI1657 device? This device looks U1.
I think recent all U1 devices work as PTP.
Linux also supports PTP, so I think we should add something ID to Linux source code. (I remember a something flag is already exist.)

Best Regards,
Masaki Ota
-----Original Message-----
From: Artem Borisov <[email protected]>
Sent: Friday, April 10, 2020 8:00 AM
Cc: [email protected]; 太田 真喜 Masaki Ota <[email protected]>; Artem Borisov <[email protected]>; Benjamin Tissoires <[email protected]>; Henrik Rydberg <[email protected]>; [email protected]; [email protected]
Subject: [PATCH 2/2] HID: alps: Refactor axis resolution logic

AUI1657 doesn't follow the same logic for resolution calculation, since the resulting values are incorrect. Instead, it reports the actual resolution values in place of the pitch ones. While we're at it, also refactor the whole resolution logic to make it more generic and sensible for multiple device support.

There are two main logical problems with the current code:
1. active_len_mm values are only used for resolution calculation on U1, yet are exposed globally as part of alps_dev structure.
2. The resolution calculation process happens in alps_input_configured, while everything else is calculated in u1_init function.

These problems become more apparent when we try to support a device that doesn't follow the same resolution calculation logic as U1.
Since alps_input_configured is a device-agnostic function, we should avoid doing any measurements there and handle them in device-specific init functions like u1/T4_init instead.

To eliminate these problems we add global x_res and y_res values and populate them on a device-specific basis in the according init functions.

---
 drivers/hid/hid-alps.c | 41 +++++++++++++++++++++++++----------------
 1 file changed, 25 insertions(+), 16 deletions(-)
drivers/hid/hid-alps.c index renamed from drivers/hid/hid-alps.c +0 -0

c2a2bd528890..494c08cca645 100644

drivers/hid/hid-alps.c +2 -2
@@ -83,8 +83,8 @@ enum dev_num {
  * @max_fingers: total number of fingers
  * @has_sp: boolean of sp existense
  * @sp_btn_info: button information
- * @x_active_len_mm: active area length of X (mm)
- * @y_active_len_mm: active area length of Y (mm)
+ * @x_res: resolution of X
+ * @y_res: resolution of Y
  * @x_max: maximum x coordinate value
  * @y_max: maximum y coordinate value
  * @x_min: minimum x coordinate value @@ -100,9 +100,10 @@ struct 
alps_dev {
        enum dev_num dev_type;
        u8  max_fingers;
        u8  has_sp;
drivers/hid/hid-alps.c +3 -6
+       u8  no_pitch;
        u8      sp_btn_info;
-       u32     x_active_len_mm;
-       u32     y_active_len_mm;
+       u32     x_res;
+       u32     y_res;
        u32     x_max;
        u32     y_max;
        u32     x_min;
@@ -550,10 +551,6 @@ static int u1_init(struct hid_device *hdev, struct alps_dev *pri_data)
                dev_err(&hdev->dev, "failed U1_RESO_DWN_ABS (%d)\n", ret);
                goto exit;
        }
-       pri_data->x_active_len_mm =
-               (pitch_x * (sen_line_num_x - 1)) / 10;
-       pri_data->y_active_len_mm =
-               (pitch_y * (sen_line_num_y - 1)) / 10;
 
        pri_data->x_max =
                (resolution << 2) * (sen_line_num_x - 1); @@ -562,6 +559,18 @@ static int u1_init(struct hid_device *hdev, struct alps_dev *pri_data)
                (resolution << 2) * (sen_line_num_y - 1);
        pri_data->y_min = 1;
drivers/hid/hid-alps.c +13 -1
+       if (pri_data->no_pitch) {
+               pri_data->x_res = pitch_x;
+               pri_data->y_res = pitch_y;
+       } else {
+               pri_data->x_res =
+                       (pri_data->x_max - 1) /
+                       ((pitch_x * (sen_line_num_x - 1)) / 10);
+               pri_data->y_res =
+                       (pri_data->y_max - 1) /
+                       ((pitch_y * (sen_line_num_y - 1)) / 10);
+       }
+
        ret = u1_read_write_register(hdev, ADDRESS_U1_PAD_BTN,
                        &tmp, 0, true);
        if (ret < 0) {
@@ -622,7 +631,7 @@ static int T4_init(struct hid_device *hdev, struct alps_dev *pri_data)
        pri_data->x_min = T4_COUNT_PER_ELECTRODE;
        pri_data->y_max = sen_line_num_y * T4_COUNT_PER_ELECTRODE;
        pri_data->y_min = T4_COUNT_PER_ELECTRODE;
-       pri_data->x_active_len_mm = pri_data->y_active_len_mm = 0;
+       pri_data->x_res = pri_data->y_res = 0;
        pri_data->btn_cnt = 1;
 
        ret = t4_read_write_register(hdev, PRM_SYS_CONFIG_1, &tmp, 0, true); @@ -675,7 +684,7 @@ static int alps_input_configured(struct hid_device *hdev, struct hid_input *hi)
        struct alps_dev *data = hid_get_drvdata(hdev);
        struct input_dev *input = hi->input, *input2;
        int ret;
drivers/hid/hid-alps.c +8 -8
-       int res_x, res_y, i;
+       int i;
 
        data->input = input;
@@ -706,12 +715,9 @@ static int alps_input_configured(struct hid_device *hdev, struct hid_input *hi)
        input_set_abs_params(input, ABS_MT_POSITION_Y,
                                                data->y_min, 
 data->y_max, 0, 0);
 
-       if (data->x_active_len_mm && data->y_active_len_mm) {
-               res_x = (data->x_max - 1) / data->x_active_len_mm;
-               res_y = (data->y_max - 1) / data->y_active_len_mm;
-
-               input_abs_set_res(input, ABS_MT_POSITION_X, res_x);
-               input_abs_set_res(input, ABS_MT_POSITION_Y, res_y);
+       if (data->x_res && data->y_res) {
+               input_abs_set_res(input, ABS_MT_POSITION_X, data->x_res);
+               input_abs_set_res(input, ABS_MT_POSITION_Y, 
+ data->y_res);
        }
 
        input_set_abs_params(input, ABS_MT_PRESSURE, 0, 64, 0, 0); @@ -802,8 +808,11 @@ static int alps_probe(struct hid_device *hdev, const struct hid_device_id *id)
                break;
        case HID_DEVICE_ID_ALPS_U1_DUAL:
        case HID_DEVICE_ID_ALPS_U1:
+               data->dev_type = U1;
+               break;
        case HID_DEVICE_ID_ALPS_1657:
                data->dev_type = U1;
+               data->no_pitch = 1;
                break;
        default:
                data->dev_type = UNKNOWN;
--

2.26.0

#14 lore raw

Re: [PATCH 2/2] HID: alps: Refactor axis resolution logic

Well, at that point it's something you should talk to hid maintainers about. The base patch is already submitted and scheduled for 5.7 as it's enough to make this touchpad work. The second one is mainly necessary to fix the deadzones around the corners and that was the one to review. If you prefer to not have any major refactoring until you prepare a better patch, I'm okay with that, since we can workaround the resolution issue via libinput quirks for now.

ср, 15 апр. 2020 г. в 13:54, Xiaojian Cao <[email protected]>:

Quoted 289 lines

Hi Artem,

Thanks for your checking, my feedbacks are as below:
1.It is about the coding style that we should not use HWID in the string "HID_DEVICE_ID_ALPS_1657", there are a large number of HWIDs using this touchpad. We should use the device type information in this string, such as "U1_UNICORN_LEGACY". 2.This is also about the coding style, we'd better make sure they are the same with each other, or just leave one list there.
3.If we'd like to upgrade the mainstream driver for only this project, then it works, but for the other projects, it has problems. If there is enough time, we'd like to prepare a better patch for most of our products.

Thank you for sharing the kernel version. I think, the review result would not be reliable if we don't have the correct source code of your kernel version.

Best Regards,
----------------------------------------------
Jason Cao(曹晓建)

-----Original Message-----
From: Artem Borisov <[email protected]>
Sent: Wednesday, April 15, 2020 5:16 PM
To: 曹 曉建 Xiaojian Cao <[email protected]>
Cc: 太田 真喜 Masaki Ota <[email protected]>; [email protected]; Benjamin Tissoires <[email protected]>; Henrik Rydberg <[email protected]>; [email protected]; [email protected]; 野村 哲哉 Tetsuya Nomura <[email protected]>; Vadim Klishko <[email protected]>; #ALCHT_ML_POD_CN <[email protected]>
Subject: Re: [PATCH 2/2] HID: alps: Refactor axis resolution logic

Hi.

I can't quite understand your objections.
1. Do you mean that we can't use AUI1657 because there are already drivers which do that (and I'm sure there are not) or that there are more devices using 0x121E?
2. The second instance of product ID is not used anywhere in the code at least for U1 so I didn't see any point to add another unused value that replicates the previous one.
3. I obviously don't have any internal documentation to argue with that, but you have mentioned above that aui1657 is just another panel based on U1, Apart from that, the touchpad is fully functional with the current code submitted which wouldn't make any sense if the report IDs were wrong.

I'm running Arch with 5.6.3 kernel, though I'm not sure how that information will be relevant to the patch.

Thanks.

ср, 15 апр. 2020 г. в 10:47, Xiaojian Cao <[email protected]>:

Quoted 252 lines

Hi Artem,

We’ve reviewed your modifications, and already found some problems as below:

It’s not suitable to use HWID AUI1657 in the source code, we because there are many projects using the same touchpad. It will confuse the coder in the future.

There are 2 places that maintain the Product ID/Device ID in the mainstream driver, currently your modifications just maintained one of them.

If we need to support the new Product ID/Device ID, then the report IDs will also be modified. Alps Alpine have different report ID list for different products.

BTW, what is your OS version and what’s its Linux kernel version?

Thank you.

Best Regards,

----------------------------------------------

Jason Cao(曹晓建)

From: Artem Borisov <[email protected]>
Sent: Wednesday, April 15, 2020 1:51 AM
To: 曹 曉建 Xiaojian Cao <[email protected]>
Cc: 太田 真喜 Masaki Ota <[email protected]>; [email protected]; Benjamin Tissoires <[email protected]>; Henrik Rydberg <[email protected]>; [email protected]; [email protected]; 野村 哲哉 Tetsuya Nomura <[email protected]>; Vadim Klishko <[email protected]>; #ALCHT_ML_POD_CN <[email protected]>
Subject: Re: [PATCH 2/2] HID: alps: Refactor axis resolution logic

Any updates on that yet?

пт, 10 апр. 2020 г., 06:28 Xiaojian Cao <[email protected]>:

Hi Ota-san,

I need to study the background first, then I will update my understanding about it.

Best Regards,
----------------------------------------------
Jason Cao(曹晓建)

-----Original Message-----
From: 太田 真喜 Masaki Ota <[email protected]>
Sent: Friday, April 10, 2020 9:51 AM
To: 曹 曉建 Xiaojian Cao <[email protected]>; Artem Borisov <[email protected]>
Cc: [email protected]; Benjamin Tissoires <[email protected]>; Henrik Rydberg <[email protected]>; [email protected]; [email protected]
Subject: RE: [PATCH 2/2] HID: alps: Refactor axis resolution logic

Hi, Cao-san,

I got it. I also confirmed this touchpad is a special. What do you think this code modification?

Best Regards,
Masaki Ota
-----Original Message-----
From: 曹 曉建 Xiaojian Cao <[email protected]>
Sent: Friday, April 10, 2020 10:03 AM
To: 太田 真喜 Masaki Ota <[email protected]>; Artem Borisov <[email protected]>
Cc: [email protected]; Benjamin Tissoires <[email protected]>; Henrik Rydberg <[email protected]>; [email protected]; [email protected]
Subject: RE: [PATCH 2/2] HID: alps: Refactor axis resolution logic

Hi Ota-san,

Thanks for your checking.
In fact, some of the U1 devices work as non-PTP.
AUI1657 is using U1(KGDBCHA004A) whose firmware just supports mouse mode and legacy mode.

Best Regards,
----------------------------------------------
Jason Cao(曹晓建)

-----Original Message-----
From: 太田 真喜 Masaki Ota <[email protected]>
Sent: Friday, April 10, 2020 8:29 AM
To: 曹 曉建 Xiaojian Cao <[email protected]>; Artem Borisov <[email protected]>
Cc: [email protected]; Benjamin Tissoires <[email protected]>; Henrik Rydberg <[email protected]>; [email protected]; [email protected]
Subject: RE: [PATCH 2/2] HID: alps: Refactor axis resolution logic

Hi, Cao-san,

Do you know AUI1657 device? This device looks U1.
I think recent all U1 devices work as PTP.
Linux also supports PTP, so I think we should add something ID to Linux source code. (I remember a something flag is already exist.)

Best Regards,
Masaki Ota
-----Original Message-----
From: Artem Borisov <[email protected]>
Sent: Friday, April 10, 2020 8:00 AM
Cc: [email protected]; 太田 真喜 Masaki Ota <[email protected]>; Artem Borisov <[email protected]>; Benjamin Tissoires <[email protected]>; Henrik Rydberg <[email protected]>; [email protected]; [email protected]
Subject: [PATCH 2/2] HID: alps: Refactor axis resolution logic

AUI1657 doesn't follow the same logic for resolution calculation, since the resulting values are incorrect. Instead, it reports the actual resolution values in place of the pitch ones. While we're at it, also refactor the whole resolution logic to make it more generic and sensible for multiple device support.

There are two main logical problems with the current code:
1. active_len_mm values are only used for resolution calculation on U1, yet are exposed globally as part of alps_dev structure.
2. The resolution calculation process happens in alps_input_configured, while everything else is calculated in u1_init function.

These problems become more apparent when we try to support a device that doesn't follow the same resolution calculation logic as U1.
Since alps_input_configured is a device-agnostic function, we should avoid doing any measurements there and handle them in device-specific init functions like u1/T4_init instead.

To eliminate these problems we add global x_res and y_res values and populate them on a device-specific basis in the according init functions.

---
 drivers/hid/hid-alps.c | 41 +++++++++++++++++++++++++----------------
 1 file changed, 25 insertions(+), 16 deletions(-)
drivers/hid/hid-alps.c index renamed from drivers/hid/hid-alps.c +0 -0

c2a2bd528890..494c08cca645 100644

drivers/hid/hid-alps.c +2 -2
@@ -83,8 +83,8 @@ enum dev_num {
  * @max_fingers: total number of fingers
  * @has_sp: boolean of sp existense
  * @sp_btn_info: button information
- * @x_active_len_mm: active area length of X (mm)
- * @y_active_len_mm: active area length of Y (mm)
+ * @x_res: resolution of X
+ * @y_res: resolution of Y
  * @x_max: maximum x coordinate value
  * @y_max: maximum y coordinate value
  * @x_min: minimum x coordinate value @@ -100,9 +100,10 @@ struct
alps_dev {
        enum dev_num dev_type;
        u8  max_fingers;
        u8  has_sp;
drivers/hid/hid-alps.c +3 -6
+       u8  no_pitch;
        u8      sp_btn_info;
-       u32     x_active_len_mm;
-       u32     y_active_len_mm;
+       u32     x_res;
+       u32     y_res;
        u32     x_max;
        u32     y_max;
        u32     x_min;
@@ -550,10 +551,6 @@ static int u1_init(struct hid_device *hdev, struct alps_dev *pri_data)
                dev_err(&hdev->dev, "failed U1_RESO_DWN_ABS (%d)\n", ret);
                goto exit;
        }
-       pri_data->x_active_len_mm =
-               (pitch_x * (sen_line_num_x - 1)) / 10;
-       pri_data->y_active_len_mm =
-               (pitch_y * (sen_line_num_y - 1)) / 10;
 
        pri_data->x_max =
                (resolution << 2) * (sen_line_num_x - 1); @@ -562,6 +559,18 @@ static int u1_init(struct hid_device *hdev, struct alps_dev *pri_data)
                (resolution << 2) * (sen_line_num_y - 1);
        pri_data->y_min = 1;
drivers/hid/hid-alps.c +13 -1
+       if (pri_data->no_pitch) {
+               pri_data->x_res = pitch_x;
+               pri_data->y_res = pitch_y;
+       } else {
+               pri_data->x_res =
+                       (pri_data->x_max - 1) /
+                       ((pitch_x * (sen_line_num_x - 1)) / 10);
+               pri_data->y_res =
+                       (pri_data->y_max - 1) /
+                       ((pitch_y * (sen_line_num_y - 1)) / 10);
+       }
+
        ret = u1_read_write_register(hdev, ADDRESS_U1_PAD_BTN,
                        &tmp, 0, true);
        if (ret < 0) {
@@ -622,7 +631,7 @@ static int T4_init(struct hid_device *hdev, struct alps_dev *pri_data)
        pri_data->x_min = T4_COUNT_PER_ELECTRODE;
        pri_data->y_max = sen_line_num_y * T4_COUNT_PER_ELECTRODE;
        pri_data->y_min = T4_COUNT_PER_ELECTRODE;
-       pri_data->x_active_len_mm = pri_data->y_active_len_mm = 0;
+       pri_data->x_res = pri_data->y_res = 0;
        pri_data->btn_cnt = 1;
 
        ret = t4_read_write_register(hdev, PRM_SYS_CONFIG_1, &tmp, 0, true); @@ -675,7 +684,7 @@ static int alps_input_configured(struct hid_device *hdev, struct hid_input *hi)
        struct alps_dev *data = hid_get_drvdata(hdev);
        struct input_dev *input = hi->input, *input2;
        int ret;
drivers/hid/hid-alps.c +8 -8
-       int res_x, res_y, i;
+       int i;
 
        data->input = input;
@@ -706,12 +715,9 @@ static int alps_input_configured(struct hid_device *hdev, struct hid_input *hi)
        input_set_abs_params(input, ABS_MT_POSITION_Y,
                                                data->y_min,
 data->y_max, 0, 0);
 
-       if (data->x_active_len_mm && data->y_active_len_mm) {
-               res_x = (data->x_max - 1) / data->x_active_len_mm;
-               res_y = (data->y_max - 1) / data->y_active_len_mm;
-
-               input_abs_set_res(input, ABS_MT_POSITION_X, res_x);
-               input_abs_set_res(input, ABS_MT_POSITION_Y, res_y);
+       if (data->x_res && data->y_res) {
+               input_abs_set_res(input, ABS_MT_POSITION_X, data->x_res);
+               input_abs_set_res(input, ABS_MT_POSITION_Y,
+ data->y_res);
        }
 
        input_set_abs_params(input, ABS_MT_PRESSURE, 0, 64, 0, 0); @@ -802,8 +808,11 @@ static int alps_probe(struct hid_device *hdev, const struct hid_device_id *id)
                break;
        case HID_DEVICE_ID_ALPS_U1_DUAL:
        case HID_DEVICE_ID_ALPS_U1:
+               data->dev_type = U1;
+               break;
        case HID_DEVICE_ID_ALPS_1657:
                data->dev_type = U1;
+               data->no_pitch = 1;
                break;
        default:
                data->dev_type = UNKNOWN;
--

2.26.0

maintainer
#17 lore raw

RE: [PATCH 2/2] HID: alps: Refactor axis resolution logic

In reply to Xiaojian Cao
Quoted 6 lines · Xiaojian Cao

Thanks for your checking, my feedbacks are as below:

1.It is about the coding style that we should not use HWID in the string "HID_DEVICE_ID_ALPS_1657", there are a large number of HWIDs using this touchpad. We should use the device type information in this string, such as "U1_UNICORN_LEGACY".

Ok, thanks for the feedback. Based on it, I am queuing the patch below.

HID_DEVICE_ID_ALPS_1657 PID is too specific, as there are many other ALPS hardware IDs using this particular touchpad.

Rename the identifier to HID_DEVICE_ID_ALPS_U1_UNICORN_LEGACY in order to describe reality better.

Fixes 640e403b1fd24 ("HID: alps: Add AUI1657 device ID")
---
 drivers/hid/hid-alps.c | 2 +-
 drivers/hid/hid-ids.h  | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)
drivers/hid/hid-alps.c +1 -1
index c2a2bd528890..b2ad319a74b9 100644
@@ -802,7 +802,7 @@ static int alps_probe(struct hid_device *hdev, const struct hid_device_id *id)
 		break;
 	case HID_DEVICE_ID_ALPS_U1_DUAL:
 	case HID_DEVICE_ID_ALPS_U1:
-	case HID_DEVICE_ID_ALPS_1657:
+	case HID_DEVICE_ID_ALPS_U1_UNICORN_LEGACY:
 		data->dev_type = U1;
 		break;
 	default:
drivers/hid/hid-ids.h +1 -1
index e3e2fa6733fb..6eb25b9e8575 100644
@@ -79,9 +79,9 @@
 #define HID_DEVICE_ID_ALPS_U1_DUAL_PTP	0x121F
 #define HID_DEVICE_ID_ALPS_U1_DUAL_3BTN_PTP	0x1220
 #define HID_DEVICE_ID_ALPS_U1		0x1215
+#define HID_DEVICE_ID_ALPS_U1_UNICORN_LEGACY         0x121E
 #define HID_DEVICE_ID_ALPS_T4_BTNLESS	0x120C
 #define HID_DEVICE_ID_ALPS_1222		0x1222
-#define HID_DEVICE_ID_ALPS_1657         0x121E
 
 #define USB_VENDOR_ID_AMI		0x046b
 #define USB_DEVICE_ID_AMI_VIRT_KEYBOARD_AND_MOUSE	0xff10
Signature · 2 lines
Jiri Kosina
SUSE Labs
#15 lore raw

RE: [PATCH 2/2] HID: alps: Refactor axis resolution logic

In reply to Artem Borisov

Hi Artem,

Yes, of course, we are also talking with Jiri.
BTW:
What's your job and responsibility?

Best Regards,
----------------------------------------------
Jason Cao(曹晓建)

-----Original Message-----
From: Artem Borisov <[email protected]>
Sent: Wednesday, April 15, 2020 6:15 PM
To: 曹 曉建 Xiaojian Cao <[email protected]>
Cc: 太田 真喜 Masaki Ota <[email protected]>; [email protected]; Benjamin Tissoires <[email protected]>; Henrik Rydberg <[email protected]>; [email protected]; [email protected]; 野村 哲哉 Tetsuya Nomura <[email protected]>; Vadim Klishko <[email protected]>; #ALCHT_ML_POD_CN <[email protected]>
Subject: Re: [PATCH 2/2] HID: alps: Refactor axis resolution logic

Well, at that point it's something you should talk to hid maintainers about. The base patch is already submitted and scheduled for 5.7 as it's enough to make this touchpad work. The second one is mainly necessary to fix the deadzones around the corners and that was the one to review. If you prefer to not have any major refactoring until you prepare a better patch, I'm okay with that, since we can workaround the resolution issue via libinput quirks for now.

ср, 15 апр. 2020 г. в 13:54, Xiaojian Cao <[email protected]>:

Quoted 299 lines

Hi Artem,

Thanks for your checking, my feedbacks are as below:
1.It is about the coding style that we should not use HWID in the string "HID_DEVICE_ID_ALPS_1657", there are a large number of HWIDs using this touchpad. We should use the device type information in this string, such as "U1_UNICORN_LEGACY". 2.This is also about the coding style, we'd better make sure they are the same with each other, or just leave one list there.
3.If we'd like to upgrade the mainstream driver for only this project, then it works, but for the other projects, it has problems. If there is enough time, we'd like to prepare a better patch for most of our products.

Thank you for sharing the kernel version. I think, the review result would not be reliable if we don't have the correct source code of your kernel version.

Best Regards,
----------------------------------------------
Jason Cao(曹晓建)

-----Original Message-----
From: Artem Borisov <[email protected]>
Sent: Wednesday, April 15, 2020 5:16 PM
To: 曹 曉建 Xiaojian Cao <[email protected]>
Cc: 太田 真喜 Masaki Ota <[email protected]>; [email protected]; Benjamin Tissoires <[email protected]>; Henrik Rydberg <[email protected]>; [email protected]; [email protected]; 野村 哲哉 Tetsuya Nomura <[email protected]>; Vadim Klishko <[email protected]>; #ALCHT_ML_POD_CN <[email protected]>
Subject: Re: [PATCH 2/2] HID: alps: Refactor axis resolution logic

Hi.

I can't quite understand your objections.
1. Do you mean that we can't use AUI1657 because there are already drivers which do that (and I'm sure there are not) or that there are more devices using 0x121E?
2. The second instance of product ID is not used anywhere in the code at least for U1 so I didn't see any point to add another unused value that replicates the previous one.
3. I obviously don't have any internal documentation to argue with that, but you have mentioned above that aui1657 is just another panel based on U1, Apart from that, the touchpad is fully functional with the current code submitted which wouldn't make any sense if the report IDs were wrong.

I'm running Arch with 5.6.3 kernel, though I'm not sure how that information will be relevant to the patch.

Thanks.

ср, 15 апр. 2020 г. в 10:47, Xiaojian Cao <[email protected]>:

Quoted 257 lines

Hi Artem,

We’ve reviewed your modifications, and already found some problems as below:

It’s not suitable to use HWID AUI1657 in the source code, we because there are many projects using the same touchpad. It will confuse the coder in the future.

There are 2 places that maintain the Product ID/Device ID in the mainstream driver, currently your modifications just maintained one of them.

If we need to support the new Product ID/Device ID, then the report IDs will also be modified. Alps Alpine have different report ID list for different products.

BTW, what is your OS version and what’s its Linux kernel version?

Thank you.

Best Regards,

----------------------------------------------

Jason Cao(曹晓建)

From: Artem Borisov <[email protected]>
Sent: Wednesday, April 15, 2020 1:51 AM
To: 曹 曉建 Xiaojian Cao <[email protected]>
Cc: 太田 真喜 Masaki Ota <[email protected]>; [email protected]; Benjamin Tissoires <[email protected]>; Henrik Rydberg <[email protected]>; [email protected]; [email protected]; 野村 哲哉 Tetsuya Nomura <[email protected]>; Vadim Klishko <[email protected]>; #ALCHT_ML_POD_CN <[email protected]>
Subject: Re: [PATCH 2/2] HID: alps: Refactor axis resolution logic

Any updates on that yet?

пт, 10 апр. 2020 г., 06:28 Xiaojian Cao <[email protected]>:

Hi Ota-san,

I need to study the background first, then I will update my understanding about it.

Best Regards,
----------------------------------------------
Jason Cao(曹晓建)

-----Original Message-----
From: 太田 真喜 Masaki Ota <[email protected]>
Sent: Friday, April 10, 2020 9:51 AM
To: 曹 曉建 Xiaojian Cao <[email protected]>; Artem Borisov <[email protected]>
Cc: [email protected]; Benjamin Tissoires <[email protected]>; Henrik Rydberg <[email protected]>; [email protected]; [email protected]
Subject: RE: [PATCH 2/2] HID: alps: Refactor axis resolution logic

Hi, Cao-san,

I got it. I also confirmed this touchpad is a special. What do you think this code modification?

Best Regards,
Masaki Ota
-----Original Message-----
From: 曹 曉建 Xiaojian Cao <[email protected]>
Sent: Friday, April 10, 2020 10:03 AM
To: 太田 真喜 Masaki Ota <[email protected]>; Artem Borisov <[email protected]>
Cc: [email protected]; Benjamin Tissoires <[email protected]>; Henrik Rydberg <[email protected]>; [email protected]; [email protected]
Subject: RE: [PATCH 2/2] HID: alps: Refactor axis resolution logic

Hi Ota-san,

Thanks for your checking.
In fact, some of the U1 devices work as non-PTP.
AUI1657 is using U1(KGDBCHA004A) whose firmware just supports mouse mode and legacy mode.

Best Regards,
----------------------------------------------
Jason Cao(曹晓建)

-----Original Message-----
From: 太田 真喜 Masaki Ota <[email protected]>
Sent: Friday, April 10, 2020 8:29 AM
To: 曹 曉建 Xiaojian Cao <[email protected]>; Artem Borisov <[email protected]>
Cc: [email protected]; Benjamin Tissoires <[email protected]>; Henrik Rydberg <[email protected]>; [email protected]; [email protected]
Subject: RE: [PATCH 2/2] HID: alps: Refactor axis resolution logic

Hi, Cao-san,

Do you know AUI1657 device? This device looks U1.
I think recent all U1 devices work as PTP.
Linux also supports PTP, so I think we should add something ID to Linux source code. (I remember a something flag is already exist.)

Best Regards,
Masaki Ota
-----Original Message-----
From: Artem Borisov <[email protected]>
Sent: Friday, April 10, 2020 8:00 AM
Cc: [email protected]; 太田 真喜 Masaki Ota <[email protected]>; Artem Borisov <[email protected]>; Benjamin Tissoires <[email protected]>; Henrik Rydberg <[email protected]>; [email protected]; [email protected]
Subject: [PATCH 2/2] HID: alps: Refactor axis resolution logic

AUI1657 doesn't follow the same logic for resolution calculation, since the resulting values are incorrect. Instead, it reports the actual resolution values in place of the pitch ones. While we're at it, also refactor the whole resolution logic to make it more generic and sensible for multiple device support.

There are two main logical problems with the current code:
1. active_len_mm values are only used for resolution calculation on U1, yet are exposed globally as part of alps_dev structure.
2. The resolution calculation process happens in alps_input_configured, while everything else is calculated in u1_init function.

These problems become more apparent when we try to support a device that doesn't follow the same resolution calculation logic as U1.
Since alps_input_configured is a device-agnostic function, we should avoid doing any measurements there and handle them in device-specific init functions like u1/T4_init instead.

To eliminate these problems we add global x_res and y_res values and populate them on a device-specific basis in the according init functions.

---
 drivers/hid/hid-alps.c | 41 
+++++++++++++++++++++++++----------------
 1 file changed, 25 insertions(+), 16 deletions(-)
drivers/hid/hid-alps.c index renamed from drivers/hid/hid-alps.c +0 -0

c2a2bd528890..494c08cca645 100644

drivers/hid/hid-alps.c +2 -2
@@ -83,8 +83,8 @@ enum dev_num {
  * @max_fingers: total number of fingers
  * @has_sp: boolean of sp existense
  * @sp_btn_info: button information
- * @x_active_len_mm: active area length of X (mm)
- * @y_active_len_mm: active area length of Y (mm)
+ * @x_res: resolution of X
+ * @y_res: resolution of Y
  * @x_max: maximum x coordinate value
  * @y_max: maximum y coordinate value
  * @x_min: minimum x coordinate value @@ -100,9 +100,10 @@ struct 
alps_dev {
        enum dev_num dev_type;
        u8  max_fingers;
        u8  has_sp;
drivers/hid/hid-alps.c +3 -6
+       u8  no_pitch;
        u8      sp_btn_info;
-       u32     x_active_len_mm;
-       u32     y_active_len_mm;
+       u32     x_res;
+       u32     y_res;
        u32     x_max;
        u32     y_max;
        u32     x_min;
@@ -550,10 +551,6 @@ static int u1_init(struct hid_device *hdev, struct alps_dev *pri_data)
                dev_err(&hdev->dev, "failed U1_RESO_DWN_ABS (%d)\n", ret);
                goto exit;
        }
-       pri_data->x_active_len_mm =
-               (pitch_x * (sen_line_num_x - 1)) / 10;
-       pri_data->y_active_len_mm =
-               (pitch_y * (sen_line_num_y - 1)) / 10;
 
        pri_data->x_max =
                (resolution << 2) * (sen_line_num_x - 1); @@ -562,6 +559,18 @@ static int u1_init(struct hid_device *hdev, struct alps_dev *pri_data)
                (resolution << 2) * (sen_line_num_y - 1);
        pri_data->y_min = 1;
drivers/hid/hid-alps.c +13 -1
+       if (pri_data->no_pitch) {
+               pri_data->x_res = pitch_x;
+               pri_data->y_res = pitch_y;
+       } else {
+               pri_data->x_res =
+                       (pri_data->x_max - 1) /
+                       ((pitch_x * (sen_line_num_x - 1)) / 10);
+               pri_data->y_res =
+                       (pri_data->y_max - 1) /
+                       ((pitch_y * (sen_line_num_y - 1)) / 10);
+       }
+
        ret = u1_read_write_register(hdev, ADDRESS_U1_PAD_BTN,
                        &tmp, 0, true);
        if (ret < 0) {
@@ -622,7 +631,7 @@ static int T4_init(struct hid_device *hdev, struct alps_dev *pri_data)
        pri_data->x_min = T4_COUNT_PER_ELECTRODE;
        pri_data->y_max = sen_line_num_y * T4_COUNT_PER_ELECTRODE;
        pri_data->y_min = T4_COUNT_PER_ELECTRODE;
-       pri_data->x_active_len_mm = pri_data->y_active_len_mm = 0;
+       pri_data->x_res = pri_data->y_res = 0;
        pri_data->btn_cnt = 1;
 
        ret = t4_read_write_register(hdev, PRM_SYS_CONFIG_1, &tmp, 0, true); @@ -675,7 +684,7 @@ static int alps_input_configured(struct hid_device *hdev, struct hid_input *hi)
        struct alps_dev *data = hid_get_drvdata(hdev);
        struct input_dev *input = hi->input, *input2;
        int ret;
drivers/hid/hid-alps.c +8 -8
-       int res_x, res_y, i;
+       int i;
 
        data->input = input;
@@ -706,12 +715,9 @@ static int alps_input_configured(struct hid_device *hdev, struct hid_input *hi)
        input_set_abs_params(input, ABS_MT_POSITION_Y,
                                                data->y_min,
 data->y_max, 0, 0);
 
-       if (data->x_active_len_mm && data->y_active_len_mm) {
-               res_x = (data->x_max - 1) / data->x_active_len_mm;
-               res_y = (data->y_max - 1) / data->y_active_len_mm;
-
-               input_abs_set_res(input, ABS_MT_POSITION_X, res_x);
-               input_abs_set_res(input, ABS_MT_POSITION_Y, res_y);
+       if (data->x_res && data->y_res) {
+               input_abs_set_res(input, ABS_MT_POSITION_X, data->x_res);
+               input_abs_set_res(input, ABS_MT_POSITION_Y,
+ data->y_res);
        }
 
        input_set_abs_params(input, ABS_MT_PRESSURE, 0, 64, 0, 0); @@ -802,8 +808,11 @@ static int alps_probe(struct hid_device *hdev, const struct hid_device_id *id)
                break;
        case HID_DEVICE_ID_ALPS_U1_DUAL:
        case HID_DEVICE_ID_ALPS_U1:
+               data->dev_type = U1;
+               break;
        case HID_DEVICE_ID_ALPS_1657:
                data->dev_type = U1;
+               data->no_pitch = 1;
                break;
        default:
                data->dev_type = UNKNOWN;
--

2.26.0

#18 lore raw

RE: [PATCH 2/2] HID: alps: Refactor axis resolution logic

In reply to Jiri Kosina

Hi Jiri,

It's my pleasure.
The latest modification is suitable now.

Best Regards,
----------------------------------------------
Jason Cao(曹晓建)

-----Original Message-----
From: Jiri Kosina <[email protected]>
Sent: Wednesday, April 15, 2020 8:55 PM
To: 曹 曉建 Xiaojian Cao <[email protected]>
Cc: Artem Borisov <[email protected]>; 太田 真喜 Masaki Ota <[email protected]>; Benjamin Tissoires <[email protected]>; Henrik Rydberg <[email protected]>; [email protected]; [email protected]; 野村 哲哉 Tetsuya Nomura <[email protected]>; Vadim Klishko <[email protected]>; #ALCHT_ML_POD_CN <[email protected]>
Subject: RE: [PATCH 2/2] HID: alps: Refactor axis resolution logic

Quoted 6 lines · Xiaojian Cao

Thanks for your checking, my feedbacks are as below:

1.It is about the coding style that we should not use HWID in the string "HID_DEVICE_ID_ALPS_1657", there are a large number of HWIDs using this touchpad. We should use the device type information in this string, such as "U1_UNICORN_LEGACY".

Ok, thanks for the feedback. Based on it, I am queuing the patch below.

HID_DEVICE_ID_ALPS_1657 PID is too specific, as there are many other ALPS hardware IDs using this particular touchpad.

Rename the identifier to HID_DEVICE_ID_ALPS_U1_UNICORN_LEGACY in order to describe reality better.

Fixes 640e403b1fd24 ("HID: alps: Add AUI1657 device ID")
---
 drivers/hid/hid-alps.c | 2 +-
 drivers/hid/hid-ids.h  | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)
drivers/hid/hid-alps.c +1 -1
@@ -802,7 +802,7 @@ static int alps_probe(struct hid_device *hdev, const struct hid_device_id *id)
 		break;
 	case HID_DEVICE_ID_ALPS_U1_DUAL:
 	case HID_DEVICE_ID_ALPS_U1:
-	case HID_DEVICE_ID_ALPS_1657:
+	case HID_DEVICE_ID_ALPS_U1_UNICORN_LEGACY:
 		data->dev_type = U1;
 		break;
 	default:
drivers/hid/hid-ids.h +1 -1
@@ -79,9 +79,9 @@
 #define HID_DEVICE_ID_ALPS_U1_DUAL_PTP	0x121F
 #define HID_DEVICE_ID_ALPS_U1_DUAL_3BTN_PTP	0x1220
 #define HID_DEVICE_ID_ALPS_U1		0x1215
+#define HID_DEVICE_ID_ALPS_U1_UNICORN_LEGACY         0x121E
 #define HID_DEVICE_ID_ALPS_T4_BTNLESS	0x120C
 #define HID_DEVICE_ID_ALPS_1222		0x1222
-#define HID_DEVICE_ID_ALPS_1657         0x121E
 
 #define USB_VENDOR_ID_AMI		0x046b
 #define USB_DEVICE_ID_AMI_VIRT_KEYBOARD_AND_MOUSE	0xff10

--
Jiri Kosina
SUSE Labs