Skip to contentSkip to conversation

i2c: designware: Use devm_platform_ioremap_resource() to simplify code

PATCH In review Andy Shevchenko 3 participants 9 messages Apr 25, 2020 – May 12, 2020

Subsystems (3)
lore
Share & tools
lore

Andy Shevchenko

author reviewer
#0 lore raw

PATCH v2 1/5 i2c: designware: Use devm_platform_ioremap_resource() to simplify code

Use devm_platform_ioremap_resource() instead of platform_get_resource() + devm_ioremap_resource().

---
v2: new patch

 drivers/i2c/busses/i2c-designware-platdrv.c | 8 ++------
 1 file changed, 2 insertions(+), 6 deletions(-)
drivers/i2c/busses/i2c-designware-platdrv.c +2 -6
index c429d664f6555..5b090480aa03e 100644
@@ -157,12 +157,10 @@ static int mscc_twi_set_sda_hold_time(struct dw_i2c_dev *dev)
 static int dw_i2c_of_configure(struct platform_device *pdev)
 {
 	struct dw_i2c_dev *dev = platform_get_drvdata(pdev);
-	struct resource *mem;
 
 	switch (dev->flags & MODEL_MASK) {
 	case MODEL_MSCC_OCELOT:
-		mem = platform_get_resource(pdev, IORESOURCE_MEM, 1);
-		dev->ext = devm_ioremap_resource(&pdev->dev, mem);
+		dev->ext = devm_platform_ioremap_resource(pdev, 1);
 		if (!IS_ERR(dev->ext))
 			dev->set_sda_hold_time = mscc_twi_set_sda_hold_time;
 		break;
@@ -241,7 +239,6 @@ static int dw_i2c_plat_probe(struct platform_device *pdev)
 	struct dw_i2c_dev *dev;
 	struct i2c_timings *t;
 	u32 acpi_speed;
-	struct resource *mem;
 	int i, irq, ret;
 
 	irq = platform_get_irq(pdev, 0);
@@ -252,8 +249,7 @@ static int dw_i2c_plat_probe(struct platform_device *pdev)
 	if (!dev)
 		return -ENOMEM;
 
-	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	dev->base = devm_ioremap_resource(&pdev->dev, mem);
+	dev->base = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(dev->base))
 		return PTR_ERR(dev->base);
 
Signature · 1 line
2.26.2
author reviewer
#1 lore raw

PATCH v2 2/5 i2c: designware: Move configuration routines to respective modules

Move configuration routines to respective modules, i.e. master and slave.

---
v2: no changes

 drivers/i2c/busses/i2c-designware-core.h    | 12 +++++++
 drivers/i2c/busses/i2c-designware-master.c  | 24 +++++++++++++
 drivers/i2c/busses/i2c-designware-platdrv.c | 38 +--------------------
 drivers/i2c/busses/i2c-designware-slave.c   | 11 ++++++
 4 files changed, 48 insertions(+), 37 deletions(-)
drivers/i2c/busses/i2c-designware-core.h +12 -0
index b220ad64c38d7..b2f894f685233 100644
@@ -314,13 +314,25 @@ static inline void __i2c_dw_disable_nowait(struct dw_i2c_dev *dev)
 
 void __i2c_dw_disable(struct dw_i2c_dev *dev);
 
+extern void i2c_dw_configure_master(struct dw_i2c_dev *dev);
 extern int i2c_dw_probe(struct dw_i2c_dev *dev);
+
 #if IS_ENABLED(CONFIG_I2C_DESIGNWARE_SLAVE)
+extern void i2c_dw_configure_slave(struct dw_i2c_dev *dev);
 extern int i2c_dw_probe_slave(struct dw_i2c_dev *dev);
 #else
+static inline void i2c_dw_configure_slave(struct dw_i2c_dev *dev) { }
 static inline int i2c_dw_probe_slave(struct dw_i2c_dev *dev) { return -EINVAL; }
 #endif
 
+static inline void i2c_dw_configure(struct dw_i2c_dev *dev)
+{
+	if (i2c_detect_slave_mode(dev->dev))
+		i2c_dw_configure_slave(dev);
+	else
+		i2c_dw_configure_master(dev);
+}
+
 #if IS_ENABLED(CONFIG_I2C_DESIGNWARE_BAYTRAIL)
 extern int i2c_dw_probe_lock_support(struct dw_i2c_dev *dev);
 #else
drivers/i2c/busses/i2c-designware-master.c +24 -0
index b6c17b550d31e..139ba98c40331 100644
@@ -657,6 +657,30 @@ static irqreturn_t i2c_dw_isr(int this_irq, void *dev_id)
 	return IRQ_HANDLED;
 }
 
+void i2c_dw_configure_master(struct dw_i2c_dev *dev)
+{
+	struct i2c_timings *t = &dev->timings;
+
+	dev->functionality = I2C_FUNC_10BIT_ADDR | DW_IC_DEFAULT_FUNCTIONALITY;
+
+	dev->master_cfg = DW_IC_CON_MASTER | DW_IC_CON_SLAVE_DISABLE |
+			  DW_IC_CON_RESTART_EN;
+
+	dev->mode = DW_IC_MASTER;
+
+	switch (t->bus_freq_hz) {
+	case I2C_MAX_STANDARD_MODE_FREQ:
+		dev->master_cfg |= DW_IC_CON_SPEED_STD;
+		break;
+	case I2C_MAX_HIGH_SPEED_MODE_FREQ:
+		dev->master_cfg |= DW_IC_CON_SPEED_HIGH;
+		break;
+	default:
+		dev->master_cfg |= DW_IC_CON_SPEED_FAST;
+	}
+}
+EXPORT_SYMBOL_GPL(i2c_dw_configure_master);
+
 static void i2c_dw_prepare_recovery(struct i2c_adapter *adap)
 {
 	struct dw_i2c_dev *dev = i2c_get_adapdata(adap);
drivers/i2c/busses/i2c-designware-platdrv.c +1 -37
index 5b090480aa03e..108b7d9d78bb5 100644
@@ -184,39 +184,6 @@ static inline int dw_i2c_of_configure(struct platform_device *pdev)
 }
 #endif
 
-static void i2c_dw_configure_master(struct dw_i2c_dev *dev)
-{
-	struct i2c_timings *t = &dev->timings;
-
-	dev->functionality = I2C_FUNC_10BIT_ADDR | DW_IC_DEFAULT_FUNCTIONALITY;
-
-	dev->master_cfg = DW_IC_CON_MASTER | DW_IC_CON_SLAVE_DISABLE |
-			  DW_IC_CON_RESTART_EN;
-
-	dev->mode = DW_IC_MASTER;
-
-	switch (t->bus_freq_hz) {
-	case I2C_MAX_STANDARD_MODE_FREQ:
-		dev->master_cfg |= DW_IC_CON_SPEED_STD;
-		break;
-	case I2C_MAX_HIGH_SPEED_MODE_FREQ:
-		dev->master_cfg |= DW_IC_CON_SPEED_HIGH;
-		break;
-	default:
-		dev->master_cfg |= DW_IC_CON_SPEED_FAST;
-	}
-}
-
-static void i2c_dw_configure_slave(struct dw_i2c_dev *dev)
-{
-	dev->functionality = I2C_FUNC_SLAVE | DW_IC_DEFAULT_FUNCTIONALITY;
-
-	dev->slave_cfg = DW_IC_CON_RX_FIFO_FULL_HLD_CTRL |
-			 DW_IC_CON_RESTART_EN | DW_IC_CON_STOP_DET_IFADDRESSED;
-
-	dev->mode = DW_IC_SLAVE;
-}
-
 static void dw_i2c_plat_pm_cleanup(struct dw_i2c_dev *dev)
 {
 	pm_runtime_disable(dev->dev);
@@ -319,10 +286,7 @@ static int dw_i2c_plat_probe(struct platform_device *pdev)
 	if (ret)
 		goto exit_reset;
 
-	if (i2c_detect_slave_mode(&pdev->dev))
-		i2c_dw_configure_slave(dev);
-	else
-		i2c_dw_configure_master(dev);
+	i2c_dw_configure(dev);
 
 	/* Optional interface clock */
 	dev->pclk = devm_clk_get_optional(&pdev->dev, "pclk");
drivers/i2c/busses/i2c-designware-slave.c +11 -0
index f5ecf76c0d024..576e7af4e94be 100644
@@ -241,6 +241,17 @@ static const struct i2c_algorithm i2c_dw_algo = {
 	.unreg_slave = i2c_dw_unreg_slave,
 };
 
+void i2c_dw_configure_slave(struct dw_i2c_dev *dev)
+{
+	dev->functionality = I2C_FUNC_SLAVE | DW_IC_DEFAULT_FUNCTIONALITY;
+
+	dev->slave_cfg = DW_IC_CON_RX_FIFO_FULL_HLD_CTRL |
+			 DW_IC_CON_RESTART_EN | DW_IC_CON_STOP_DET_IFADDRESSED;
+
+	dev->mode = DW_IC_SLAVE;
+}
+EXPORT_SYMBOL_GPL(i2c_dw_configure_slave);
+
 int i2c_dw_probe_slave(struct dw_i2c_dev *dev)
 {
 	struct i2c_adapter *adap = &dev->adapter;
Signature · 1 line
2.26.2
author reviewer
#2 lore raw

PATCH v2 3/5 i2c: designware: Switch PCI driver to use i2c_dw_configure_master()

In reply to Andy Shevchenko

Since we have available helper to configure master mode, let's use it in the PCI driver instead of spread open-coded variant.

---
v2: new patch

 drivers/i2c/busses/i2c-designware-pcidrv.c | 33 +++++-----------------
 1 file changed, 7 insertions(+), 26 deletions(-)
drivers/i2c/busses/i2c-designware-pcidrv.c +7 -26
index 7a0b65b5b5b59..d5e5abc03683f 100644
@@ -46,20 +46,14 @@ struct dw_scl_sda_cfg {
 
 struct dw_pci_controller {
 	u32 bus_num;
-	u32 bus_cfg;
 	u32 tx_fifo_depth;
 	u32 rx_fifo_depth;
 	u32 clk_khz;
-	u32 functionality;
 	u32 flags;
 	struct dw_scl_sda_cfg *scl_sda_cfg;
 	int (*setup)(struct pci_dev *pdev, struct dw_pci_controller *c);
 };
 
-#define INTEL_MID_STD_CFG  (DW_IC_CON_MASTER |			\
-				DW_IC_CON_SLAVE_DISABLE |	\
-				DW_IC_CON_RESTART_EN)
-
 /* Merrifield HCNT/LCNT/SDA hold time */
 static struct dw_scl_sda_cfg mrfld_config = {
 	.ss_hcnt = 0x2f8,
@@ -88,10 +82,11 @@ static struct dw_scl_sda_cfg hsw_config = {
 
 static int mfld_setup(struct pci_dev *pdev, struct dw_pci_controller *c)
 {
+	struct dw_i2c_dev *dev = dev_get_drvdata(&pdev->dev);
+
 	switch (pdev->device) {
 	case 0x0817:
-		c->bus_cfg &= ~DW_IC_CON_SPEED_MASK;
-		c->bus_cfg |= DW_IC_CON_SPEED_STD;
+		dev->timings.bus_freq_hz = I2C_MAX_STANDARD_MODE_FREQ;
 		/* fall through */
 	case 0x0818:
 	case 0x0819:
@@ -128,53 +123,41 @@ static int mrfld_setup(struct pci_dev *pdev, struct dw_pci_controller *c)
 static struct dw_pci_controller dw_pci_controllers[] = {
 	[medfield] = {
 		.bus_num = -1,
-		.bus_cfg   = INTEL_MID_STD_CFG | DW_IC_CON_SPEED_FAST,
 		.tx_fifo_depth = 32,
 		.rx_fifo_depth = 32,
-		.functionality = I2C_FUNC_10BIT_ADDR,
 		.clk_khz      = 25000,
 		.setup = mfld_setup,
 	},
 	[merrifield] = {
 		.bus_num = -1,
-		.bus_cfg = INTEL_MID_STD_CFG | DW_IC_CON_SPEED_FAST,
 		.tx_fifo_depth = 64,
 		.rx_fifo_depth = 64,
-		.functionality = I2C_FUNC_10BIT_ADDR,
 		.scl_sda_cfg = &mrfld_config,
 		.setup = mrfld_setup,
 	},
 	[baytrail] = {
 		.bus_num = -1,
-		.bus_cfg = INTEL_MID_STD_CFG | DW_IC_CON_SPEED_FAST,
 		.tx_fifo_depth = 32,
 		.rx_fifo_depth = 32,
-		.functionality = I2C_FUNC_10BIT_ADDR,
 		.scl_sda_cfg = &byt_config,
 	},
 	[haswell] = {
 		.bus_num = -1,
-		.bus_cfg = INTEL_MID_STD_CFG | DW_IC_CON_SPEED_FAST,
 		.tx_fifo_depth = 32,
 		.rx_fifo_depth = 32,
-		.functionality = I2C_FUNC_10BIT_ADDR,
 		.scl_sda_cfg = &hsw_config,
 	},
 	[cherrytrail] = {
 		.bus_num = -1,
-		.bus_cfg = INTEL_MID_STD_CFG | DW_IC_CON_SPEED_FAST,
 		.tx_fifo_depth = 32,
 		.rx_fifo_depth = 32,
-		.functionality = I2C_FUNC_10BIT_ADDR,
 		.flags = MODEL_CHERRYTRAIL,
 		.scl_sda_cfg = &byt_config,
 	},
 	[elkhartlake] = {
 		.bus_num = -1,
-		.bus_cfg = INTEL_MID_STD_CFG | DW_IC_CON_SPEED_FAST,
 		.tx_fifo_depth = 32,
 		.rx_fifo_depth = 32,
-		.functionality = I2C_FUNC_10BIT_ADDR,
 		.clk_khz = 100000,
 	},
 };
@@ -250,14 +233,16 @@ static int i2c_dw_pci_probe(struct pci_dev *pdev,
 	if (r < 0)
 		return r;
 
-	dev->clk = NULL;
 	dev->controller = controller;
 	dev->get_clk_rate_khz = i2c_dw_get_clk_rate_khz;
+	dev->timings.bus_freq_hz = I2C_MAX_FAST_MODE_FREQ;
 	dev->base = pcim_iomap_table(pdev)[0];
 	dev->dev = &pdev->dev;
 	dev->irq = pci_irq_vector(pdev, 0);
 	dev->flags |= controller->flags;
 
+	pci_set_drvdata(pdev, dev);
+
 	if (controller->setup) {
 		r = controller->setup(pdev, controller);
 		if (r) {
@@ -266,10 +251,8 @@ static int i2c_dw_pci_probe(struct pci_dev *pdev,
 		}
 	}
 
-	dev->functionality = controller->functionality |
-				DW_IC_DEFAULT_FUNCTIONALITY;
+	i2c_dw_configure_master(dev);
 
-	dev->master_cfg = controller->bus_cfg;
 	if (controller->scl_sda_cfg) {
 		cfg = controller->scl_sda_cfg;
 		dev->ss_hcnt = cfg->ss_hcnt;
@@ -279,8 +262,6 @@ static int i2c_dw_pci_probe(struct pci_dev *pdev,
 		dev->sda_hold_time = cfg->sda_hold;
 	}
 
-	pci_set_drvdata(pdev, dev);
-
 	dev->tx_fifo_depth = controller->tx_fifo_depth;
 	dev->rx_fifo_depth = controller->rx_fifo_depth;
 
Signature · 1 line
2.26.2
author reviewer
#3 lore raw

PATCH v2 4/5 i2c: designware: Rename i2c_dw_probe() to i2c_dw_probe_master()

In reply to Andy Shevchenko

As a preparatory patch to support slave mode for PCI enumerated devices rename i2c_dw_probe() to i2c_dw_probe_master() and split common i2c_dw_probe() as inline helper.

---
v2: drop MASTER module optional choice (Jarkko, Wolfram)

 drivers/i2c/busses/Makefile                 |  3 ++-
 drivers/i2c/busses/i2c-designware-core.h    | 15 ++++++++++++++-
 drivers/i2c/busses/i2c-designware-master.c  |  4 ++--
 drivers/i2c/busses/i2c-designware-pcidrv.c  |  2 +-
 drivers/i2c/busses/i2c-designware-platdrv.c |  6 +-----
 5 files changed, 20 insertions(+), 10 deletions(-)
drivers/i2c/busses/Makefile +2 -1
index c852d27370377..d5f56e6179a4b 100644
@@ -49,7 +49,8 @@ obj-$(CONFIG_I2C_CBUS_GPIO)	+= i2c-cbus-gpio.o
 obj-$(CONFIG_I2C_CPM)		+= i2c-cpm.o
 obj-$(CONFIG_I2C_DAVINCI)	+= i2c-davinci.o
 obj-$(CONFIG_I2C_DESIGNWARE_CORE)	+= i2c-designware-core.o
-i2c-designware-core-objs := i2c-designware-common.o i2c-designware-master.o
+i2c-designware-core-objs := i2c-designware-common.o
+i2c-designware-core-objs += i2c-designware-master.o
 ifeq ($(CONFIG_I2C_DESIGNWARE_SLAVE),y)
 i2c-designware-core-objs += i2c-designware-slave.o
 endif
drivers/i2c/busses/i2c-designware-core.h +14 -1
index b2f894f685233..1674caf277451 100644
@@ -315,7 +315,7 @@ static inline void __i2c_dw_disable_nowait(struct dw_i2c_dev *dev)
 void __i2c_dw_disable(struct dw_i2c_dev *dev);
 
 extern void i2c_dw_configure_master(struct dw_i2c_dev *dev);
-extern int i2c_dw_probe(struct dw_i2c_dev *dev);
+extern int i2c_dw_probe_master(struct dw_i2c_dev *dev);
 
 #if IS_ENABLED(CONFIG_I2C_DESIGNWARE_SLAVE)
 extern void i2c_dw_configure_slave(struct dw_i2c_dev *dev);
@@ -325,6 +325,19 @@ static inline void i2c_dw_configure_slave(struct dw_i2c_dev *dev) { }
 static inline int i2c_dw_probe_slave(struct dw_i2c_dev *dev) { return -EINVAL; }
 #endif
 
+static inline int i2c_dw_probe(struct dw_i2c_dev *dev)
+{
+	switch (dev->mode) {
+	case DW_IC_SLAVE:
+		return i2c_dw_probe_slave(dev);
+	case DW_IC_MASTER:
+		return i2c_dw_probe_master(dev);
+	default:
+		dev_err(dev->dev, "Wrong operation mode: %d\n", dev->mode);
+		return -EINVAL;
+	}
+}
+
 static inline void i2c_dw_configure(struct dw_i2c_dev *dev)
 {
 	if (i2c_detect_slave_mode(dev->dev))
drivers/i2c/busses/i2c-designware-master.c +2 -2
index 139ba98c40331..95eeec53c744f 100644
@@ -727,7 +727,7 @@ static int i2c_dw_init_recovery_info(struct dw_i2c_dev *dev)
 	return 0;
 }
 
-int i2c_dw_probe(struct dw_i2c_dev *dev)
+int i2c_dw_probe_master(struct dw_i2c_dev *dev)
 {
 	struct i2c_adapter *adap = &dev->adapter;
 	unsigned long irq_flags;
@@ -794,7 +794,7 @@ int i2c_dw_probe(struct dw_i2c_dev *dev)
 
 	return ret;
 }
-EXPORT_SYMBOL_GPL(i2c_dw_probe);
+EXPORT_SYMBOL_GPL(i2c_dw_probe_master);
 
 MODULE_DESCRIPTION("Synopsys DesignWare I2C bus master adapter");
 MODULE_LICENSE("GPL");
drivers/i2c/busses/i2c-designware-pcidrv.c +1 -1
index d5e5abc03683f..7e994f366a5e8 100644
@@ -271,7 +271,7 @@ static int i2c_dw_pci_probe(struct pci_dev *pdev,
 	ACPI_COMPANION_SET(&adap->dev, ACPI_COMPANION(&pdev->dev));
 	adap->nr = controller->bus_num;
 
-	r = i2c_dw_probe(dev);
+	r = i2c_dw_probe_master(dev);
 	if (r) {
 		pci_free_irq_vectors(pdev);
 		return r;
drivers/i2c/busses/i2c-designware-platdrv.c +1 -5
index 108b7d9d78bb5..7e228ff91ad48 100644
@@ -337,11 +337,7 @@ static int dw_i2c_plat_probe(struct platform_device *pdev)
 
 	pm_runtime_enable(&pdev->dev);
 
-	if (dev->mode == DW_IC_SLAVE)
-		ret = i2c_dw_probe_slave(dev);
-	else
-		ret = i2c_dw_probe(dev);
-
+	ret = i2c_dw_probe(dev);
 	if (ret)
 		goto exit_probe;
 
Signature · 1 line
2.26.2
author reviewer
#4 lore raw

PATCH v2 5/5 i2c: designware: Allow slave mode for PCI enumerated devices

In reply to Andy Shevchenko

Allow slave mode for PCI enumerated devices by calling a common i2c_dw_probe() instead of i2c_dw_probe_master().

While dropping dependency to platform driver in slave module, move its configuration section above, closer to core.

---
v2: new patch

 drivers/i2c/busses/Kconfig                 | 21 ++++++++++-----------
 drivers/i2c/busses/i2c-designware-pcidrv.c |  4 ++--
 2 files changed, 12 insertions(+), 13 deletions(-)
drivers/i2c/busses/Kconfig +10 -11
index 70a561bff74a6..b1ad26269cc63 100644
@@ -527,6 +527,16 @@ config I2C_DAVINCI
 config I2C_DESIGNWARE_CORE
 	tristate
 
+config I2C_DESIGNWARE_SLAVE
+	bool "Synopsys DesignWare Slave"
+	select I2C_SLAVE
+	help
+	  If you say yes to this option, support will be included for the
+	  Synopsys DesignWare I2C slave adapter.
+
+	  This is not a standalone module, this module compiles together with
+	  i2c-designware-core.
+
 config I2C_DESIGNWARE_PLATFORM
 	tristate "Synopsys DesignWare Platform"
 	select I2C_DESIGNWARE_CORE
@@ -538,17 +548,6 @@ config I2C_DESIGNWARE_PLATFORM
 	  This driver can also be built as a module.  If so, the module
 	  will be called i2c-designware-platform.
 
-config I2C_DESIGNWARE_SLAVE
-	bool "Synopsys DesignWare Slave"
-	select I2C_SLAVE
-	depends on I2C_DESIGNWARE_PLATFORM
-	help
-	  If you say yes to this option, support will be included for the
-	  Synopsys DesignWare I2C slave adapter.
-
-	  This is not a standalone module, this module compiles together with
-	  i2c-designware-core.
-
 config I2C_DESIGNWARE_PCI
 	tristate "Synopsys DesignWare PCI"
 	depends on PCI
drivers/i2c/busses/i2c-designware-pcidrv.c +2 -2
index 7e994f366a5e8..c762e5a11e44e 100644
@@ -251,7 +251,7 @@ static int i2c_dw_pci_probe(struct pci_dev *pdev,
 		}
 	}
 
-	i2c_dw_configure_master(dev);
+	i2c_dw_configure(dev);
 
 	if (controller->scl_sda_cfg) {
 		cfg = controller->scl_sda_cfg;
@@ -271,7 +271,7 @@ static int i2c_dw_pci_probe(struct pci_dev *pdev,
 	ACPI_COMPANION_SET(&adap->dev, ACPI_COMPANION(&pdev->dev));
 	adap->nr = controller->bus_num;
 
-	r = i2c_dw_probe_master(dev);
+	r = i2c_dw_probe(dev);
 	if (r) {
 		pci_free_irq_vectors(pdev);
 		return r;
Signature · 1 line
2.26.2
Acked-by on v2 5/5
#5 lore raw

Re: [PATCH v2 5/5] i2c: designware: Allow slave mode for PCI enumerated devices

Quoted 6 lines · Andy Shevchenko

Allow slave mode for PCI enumerated devices by calling a common i2c_dw_probe() instead of i2c_dw_probe_master().

While dropping dependency to platform driver in slave module, move its configuration section above, closer to core.

Quoted 7 lines

---
v2: new patch

  drivers/i2c/busses/Kconfig                 | 21 ++++++++++-----------
  drivers/i2c/busses/i2c-designware-pcidrv.c |  4 ++--
  2 files changed, 12 insertions(+), 13 deletions(-)

To all 5 patches

#6 lore raw

Re: [PATCH v2 5/5] i2c: designware: Allow slave mode for PCI enumerated devices

Quoted 14 lines · Jarkko Nikula
Quoted 6 lines · Andy Shevchenko

Allow slave mode for PCI enumerated devices by calling a common i2c_dw_probe() instead of i2c_dw_probe_master().

While dropping dependency to platform driver in slave module, move its configuration section above, closer to core.

Quoted 7 lines

---
v2: new patch

  drivers/i2c/busses/Kconfig                 | 21 ++++++++++-----------
  drivers/i2c/busses/i2c-designware-pcidrv.c |  4 ++--
  2 files changed, 12 insertions(+), 13 deletions(-)
Quoted 3 lines

To all 5 patches

And all applied to for-next, thanks!

author reviewer
#7 lore raw

Re: [PATCH v2 5/5] i2c: designware: Allow slave mode for PCI enumerated devices

Quoted 15 lines · Wolfram Sang
Quoted 14 lines · Jarkko Nikula
Quoted 13 lines · Andy Shevchenko

Allow slave mode for PCI enumerated devices by calling a common i2c_dw_probe() instead of i2c_dw_probe_master().

While dropping dependency to platform driver in slave module, move its configuration section above, closer to core.

---
v2: new patch

  drivers/i2c/busses/Kconfig                 | 21 ++++++++++-----------
  drivers/i2c/busses/i2c-designware-pcidrv.c |  4 ++--
  2 files changed, 12 insertions(+), 13 deletions(-)
Quoted 5 lines
Quoted 3 lines

To all 5 patches

And all applied to for-next, thanks!

Wolfram, I do not see them in your tree. Neither Linux next has them. Something should I do?

Signature · 2 lines
With Best Regards,
Andy Shevchenko
#8 lore raw

Re: [PATCH v2 5/5] i2c: designware: Allow slave mode for PCI enumerated devices

Quoted 5 lines
Quoted 2 lines

And all applied to for-next, thanks!

Wolfram, I do not see them in your tree. Neither Linux next has them. Something should I do?

Sorry, Andy. I lost them when I was not correctly syncing from my secondary machine. Pushed them out now.