arm64: dts: imx8mm: Add node for SPDIF
Subsystems (2)
PATCH 1/1 arm64: dts: imx8mm: Add node for SPDIF
The i.MX8M Mini can support SPIDF which is very similar to the IP used on the i.MX35.
This patch adds the SPIF node.
Signed-off-by Adam Ford <[email protected]>
arch/arm64/boot/dts/freescale/imx8mm.dtsi +23 -0
@@ -358,6 +358,29 @@ micfil: micfil@30080000 { status = "disabled"; }; + spdif1: spdif@30090000 { + compatible = "fsl,imx8mm-spdif", "fsl,imx35-spdif"; + reg = <0x30090000 0x10000>; + interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk IMX8MM_CLK_AUDIO_AHB>, /* core */ + <&clk IMX8MM_CLK_24M>, /* rxtx0 */ + <&clk IMX8MM_CLK_SPDIF1>, /* rxtx1 */ + <&clk IMX8MM_CLK_DUMMY>, /* rxtx2 */ + <&clk IMX8MM_CLK_DUMMY>, /* rxtx3 */ + <&clk IMX8MM_CLK_DUMMY>, /* rxtx4 */ + <&clk IMX8MM_CLK_AUDIO_AHB>, /* rxtx5 */ + <&clk IMX8MM_CLK_DUMMY>, /* rxtx6 */ + <&clk IMX8MM_CLK_DUMMY>, /* rxtx7 */ + <&clk IMX8MM_CLK_DUMMY>; /* spba */ + clock-names = "core", "rxtx0", + "rxtx1", "rxtx2", + "rxtx3", "rxtx4", + "rxtx5", "rxtx6", + "rxtx7", "spba"; + dmas = <&sdma2 28 18 0>, <&sdma2 29 18 0>; + dma-names = "rx", "tx"; + status = "disabled"; + }; gpio1: gpio@30200000 { compatible = "fsl,imx8mm-gpio", "fsl,imx35-gpio"; reg = <0x30200000 0x10000>;
Signature · 1 line
2.25.1
Quoted 12 lines · Adam Ford
The i.MX8M Mini can support SPIDF which is very similar to the IP used on the i.MX35.
This patch adds the SPIF node.
Signed-off-by Adam Ford <[email protected]>arch/arm64/boot/dts/freescale/imx8mm.dtsi +0
-0
arch/arm64/boot/dts/freescale/imx8mm.dtsi micfil: micfil@30080000 { · line 361
Quoted 4 lines
arch/arm64/boot/dts/freescale/imx8mm.dtsi +1
-0@@ -358,6 +358,29 @@ micfil: micfil@30080000 { status = "disabled"; }; + spdif1: spdif@30090000 {
It should be in a patch series with previous micfil one, as it cannot be applied independently.
Quoted 12 lines
arch/arm64/boot/dts/freescale/imx8mm.dtsi +12
-0+ compatible = "fsl,imx8mm-spdif", "fsl,imx35-spdif"; + reg = <0x30090000 0x10000>; + interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk IMX8MM_CLK_AUDIO_AHB>, /* core */ + <&clk IMX8MM_CLK_24M>, /* rxtx0 */ + <&clk IMX8MM_CLK_SPDIF1>, /* rxtx1 */ + <&clk IMX8MM_CLK_DUMMY>, /* rxtx2 */ + <&clk IMX8MM_CLK_DUMMY>, /* rxtx3 */ + <&clk IMX8MM_CLK_DUMMY>, /* rxtx4 */ + <&clk IMX8MM_CLK_AUDIO_AHB>, /* rxtx5 */ + <&clk IMX8MM_CLK_DUMMY>, /* rxtx6 */ + <&clk IMX8MM_CLK_DUMMY>, /* rxtx7 */
arch/arm64/boot/dts/freescale/imx8mm.dtsi micfil: micfil@30080000 { · line 383
Quoted 10 lines
arch/arm64/boot/dts/freescale/imx8mm.dtsi +10
-0+ <&clk IMX8MM_CLK_DUMMY>; /* spba */ + clock-names = "core", "rxtx0", + "rxtx1", "rxtx2", + "rxtx3", "rxtx4", + "rxtx5", "rxtx6", + "rxtx7", "spba"; + dmas = <&sdma2 28 18 0>, <&sdma2 29 18 0>; + dma-names = "rx", "tx"; + status = "disabled"; + };
Have a newline between nodes.
Shawn
Quoted 6 lines
arch/arm64/boot/dts/freescale/imx8mm.dtsi +0
-0gpio1: gpio@30200000 { compatible = "fsl,imx8mm-gpio", "fsl,imx35-gpio"; reg = <0x30200000 0x10000>;Signature · 1 line
2.25.1