imx8mp_evk: Add a README file
Fabio Estevam
reviewerPATCH 1/1 imx8mp_evk: Add a README file
Add a README file explaining the U-Boot build and SD card flash procedures.
Signed-off-by Fabio Estevam <[email protected]>
--- board/freescale/imx8mp_evk/README | 41 +++++++++++++++++++++++++++++++ 1 file changed, 41 insertions(+) create mode 100644 board/freescale/imx8mp_evk/README
board/freescale/imx8mp_evk/README new file +41 -0
@@ -0,0 +1,41 @@ +U-Boot for the NXP i.MX8MP EVK board + +Quick Start +=========== +- Build the ARM Trusted firmware binary +- Get the firmware-imx package +- Build U-Boot +- Boot + +Get and Build the ARM Trusted firmware +====================================== +Note: $(srctree) is the U-Boot source directory +Get ATF from: https://source.codeaurora.org/external/imx/imx-atf +branch: imx_5.4.3_2.0.0 +$ make PLAT=imx8mp bl31 +$ sudo cp build/imx8mp/release/bl31.bin $(srctree) + +Get the ddr firmware +==================== +$ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.7.bin +$ chmod +x firmware-imx-8.7.bin +$ ./firmware-imx-8.7 +$ sudo cp firmware-imx-8.7/firmware/ddr/synopsys/lpddr4_pmu_train_1d_dmem_201904.bin $(srctree)/lpddr4_pmu_train_1d_dmem.bin +$ sudo cp firmware-imx-8.7/firmware/ddr/synopsys/lpddr4_pmu_train_1d_imem_201904.bin $(srctree)/lpddr4_pmu_train_1d_imem.bin +$ sudo cp firmware-imx-8.7/firmware/ddr/synopsys/lpddr4_pmu_train_2d_dmem_201904.bin $(srctree)/lpddr4_pmu_train_2d_dmem.bin +$ sudo cp firmware-imx-8.7/firmware/ddr/synopsys/lpddr4_pmu_train_2d_imem_201904.bin $(srctree)/lpddr4_pmu_train_2d_imem.bin + +Build U-Boot +============ +$ export CROSS_COMPILE=aarch64-poky-linux- +$ make imx8mp_evk_defconfig +$ export ATF_LOAD_ADDR=0x960000 +$ make flash.bin + +Burn the flash.bin to the MicroSD card at offset 32KB +$sudo dd if=flash.bin of=/dev/sd[x] bs=1K seek=32; sync + +Boot +==== +Set Boot switch to SD boot +Use /dev/ttyUSB2 for U-Boot console
Signature · 1 line
2.17.1
PATCH 1/1 imx8mp_evk: Add a README file
Quoted 2 lines
Add a README file explaining the U-Boot build and SD card flash procedures.
Signed-off-by Fabio Estevam <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================