arm64: dts: rk3399-nanopi4: Add u-boot,spl-boot-order
Subsystems (2)
PATCH 1/3 arm64: dts: rk3399-nanopi4: Add u-boot,spl-boot-order
Add u-boot,spl-boot-order as sdhci and sdmmc for booting from eMMC and SD card.
--- arch/arm/dts/rk3399-nanopi4-u-boot.dtsi | 6 ++++++ 1 file changed, 6 insertions(+)
arch/arm/dts/rk3399-nanopi4-u-boot.dtsi +6 -0
@@ -5,6 +5,12 @@ #include "rk3399-u-boot.dtsi" +/{ + chosen { + u-boot,spl-boot-order = "same-as-spl", &sdhci, &sdmmc; + }; +}; + &sdmmc { pinctrl-0 = <&sdmmc_bus4 &sdmmc_clk &sdmmc_cmd &sdmmc_cd>; };
Signature · 1 line
2.25.1
A message that is not in the archive (sent off-list or not yet received): 20200524173213.201123-1-jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org
PATCH 2/3 nanopc-t4: Enable USB Gadget
Enable DWC3 core, gadget for nanopc-t4 board.
This would help to use fastboot by default.
--- configs/nanopc-t4-rk3399_defconfig | 3 +++ 1 file changed, 3 insertions(+)
configs/nanopc-t4-rk3399_defconfig +3 -0
@@ -50,7 +50,10 @@ CONFIG_USB_XHCI_HCD=y CONFIG_USB_XHCI_DWC3=y CONFIG_USB_EHCI_HCD=y CONFIG_USB_EHCI_GENERIC=y +CONFIG_USB_DWC3=y +CONFIG_ROCKCHIP_USB2_PHY=y CONFIG_USB_KEYBOARD=y +CONFIG_USB_GADGET=y CONFIG_USB_HOST_ETHER=y CONFIG_USB_ETHER_ASIX=y CONFIG_USB_ETHER_ASIX88179=y
Signature · 1 line
2.25.1
A message that is not in the archive (sent off-list or not yet received): 20200524173213.201123-2-jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org
Kever Yang
Reviewed-byRe: [PATCH 2/3] nanopc-t4: Enable USB Gadget
Quoted 5 lines · Jagan Teki
Enable DWC3 core, gadget for nanopc-t4 board.
This would help to use fastboot by default.
Signed-off-by Jagan Teki <[email protected]>
Thanks,
- Kever
Quoted 9 lines
--- configs/nanopc-t4-rk3399_defconfig | 3 +++ 1 file changed, 3 insertions(+)configs/nanopc-t4-rk3399_defconfig +0
-0
configs/nanopc-t4-rk3399_defconfig CONFIG_USB_XHCI_HCD=y · line 59
Quoted 10 lines
configs/nanopc-t4-rk3399_defconfig +3
-0@@ -50,7 +50,10 @@ CONFIG_USB_XHCI_HCD=y CONFIG_USB_XHCI_DWC3=y CONFIG_USB_EHCI_HCD=y CONFIG_USB_EHCI_GENERIC=y +CONFIG_USB_DWC3=y +CONFIG_ROCKCHIP_USB2_PHY=y CONFIG_USB_KEYBOARD=y +CONFIG_USB_GADGET=y CONFIG_USB_HOST_ETHER=y CONFIG_USB_ETHER_ASIX=y CONFIG_USB_ETHER_ASIX88179=y
_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip
PATCH 3/3 doc: rockchip: Document eMMC program steps
In reply to Jagan TekiDocument eMMC partition creation and program steps for rockchip platforms.
--- doc/board/rockchip/rockchip.rst | 32 ++++++++++++++++++++++++++++++-- 1 file changed, 30 insertions(+), 2 deletions(-)
doc/board/rockchip/rockchip.rst +30 -2
@@ -117,14 +117,42 @@ To write an image that boots from an SD card (assumed to be /dev/sda):: sudo dd if=u-boot-rockchip.bin of=/dev/sda seek=64 sync +eMMC +^^^^ + +eMMC flash would probe on mmc0 in most of the rockchip platforms. + +Create GPT partition layout as defined in configurations:: + + mmc dev 0 + gpt write mmc 0 $partitions + +Connect the USB-OTG cable between host and target device. + +Launch fastboot at target:: + + fastboot 0 + +Upon successful gadget connection,host show the USB device like:: + + lsusb + Bus 001 Device 020: ID 2207:330c Fuzhou Rockchip Electronics Company RK3399 in Mask ROM mode + +Program the flash:: + + sudo fastboot -i 0x2207 flash loader1 idbloader.img + sudo fastboot -i 0x2207 flash loader2 u-boot.itb + +Note: for rockchip 32-bit platforms the U-Boot proper image +is u-boot-dtb.img + TODO ---- - Add rockchip idbloader image building - Add rockchip TPL image building - Document SPI flash boot -- Describe steps for eMMC flashing - Add missing SoC's with it boards list .. Jagan Teki <[email protected]> -.. Fri Jan 10 00:08:40 IST 2020 +.. Sunday 24 May 2020 10:08:41 PM IST
Signature · 1 line
2.25.1
Re: [PATCH 3/3] doc: rockchip: Document eMMC program steps
Quoted 4 lines · Jagan Teki
Document eMMC partition creation and program steps for rockchip platforms.
Signed-off-by Jagan Teki <[email protected]>
Thanks,
- Kever
Quoted 53 lines
--- doc/board/rockchip/rockchip.rst | 32 ++++++++++++++++++++++++++++++-- 1 file changed, 30 insertions(+), 2 deletions(-)doc/board/rockchip/rockchip.rst +30
-2@@ -117,14 +117,42 @@ To write an image that boots from an SD card (assumed to be /dev/sda):: sudo dd if=u-boot-rockchip.bin of=/dev/sda seek=64 sync +eMMC +^^^^ + +eMMC flash would probe on mmc0 in most of the rockchip platforms. + +Create GPT partition layout as defined in configurations:: + + mmc dev 0 + gpt write mmc 0 $partitions + +Connect the USB-OTG cable between host and target device. + +Launch fastboot at target:: + + fastboot 0 + +Upon successful gadget connection,host show the USB device like:: + + lsusb + Bus 001 Device 020: ID 2207:330c Fuzhou Rockchip Electronics Company RK3399 in Mask ROM mode + +Program the flash:: + + sudo fastboot -i 0x2207 flash loader1 idbloader.img + sudo fastboot -i 0x2207 flash loader2 u-boot.itb + +Note: for rockchip 32-bit platforms the U-Boot proper image +is u-boot-dtb.img + TODO ---- - Add rockchip idbloader image building - Add rockchip TPL image building - Document SPI flash boot -- Describe steps for eMMC flashing - Add missing SoC's with it boards list .. Jagan Teki <[email protected]> -.. Fri Jan 10 00:08:40 IST 2020 +.. Sunday 24 May 2020 10:08:41 PM IST
Re: [PATCH 1/3] arm64: dts: rk3399-nanopi4: Add u-boot, spl-boot-order
In reply to Jagan TekiQuoted 4 lines · Jagan Teki
Add u-boot,spl-boot-order as sdhci and sdmmc for booting from eMMC and SD card.
Signed-off-by Jagan Teki <[email protected]>
Thanks,
- Kever
Quoted 21 lines
--- arch/arm/dts/rk3399-nanopi4-u-boot.dtsi | 6 ++++++ 1 file changed, 6 insertions(+)arch/arm/dts/rk3399-nanopi4-u-boot.dtsi +6
-0@@ -5,6 +5,12 @@ #include "rk3399-u-boot.dtsi" +/{ + chosen { + u-boot,spl-boot-order = "same-as-spl", &sdhci, &sdmmc; + }; +}; + &sdmmc { pinctrl-0 = <&sdmmc_bus4 &sdmmc_clk &sdmmc_cmd &sdmmc_cd>; };