Skip to contentSkip to conversation

spi: mux: repair mux usage

PATCH In review Peter Rosin 3 participants 3 messages May 25, 2020 SPI

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 spi: mux: repair mux usage

It is not valid to cache/short out selection of the mux.

mux_control_select() only locks the mux until mux_control_deselect() is called. mux_control_deselect() may put the mux in some low power state or some other user of the mux might select it for other purposes. These things are probably not happening in the original setting where this driver was developed, but it is said to be a generic SPI mux.

Also, the mux framework will short out the actual low level muxing operation when/if that is possible.

Fixes e9e40543ad5b ("spi: Add generic SPI multiplexer")
---
 drivers/spi/spi-mux.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)
drivers/spi/spi-mux.c +4 -4
index 4f94c9127fc1..cc9ef371db14 100644
@@ -51,6 +51,10 @@ static int spi_mux_select(struct spi_device *spi)
 	struct spi_mux_priv *priv = spi_controller_get_devdata(spi->controller);
 	int ret;
 
+	ret = mux_control_select(priv->mux, spi->chip_select);
+	if (ret)
+		return ret;
+
 	if (priv->current_cs == spi->chip_select)
 		return 0;
 
@@ -62,10 +66,6 @@ static int spi_mux_select(struct spi_device *spi)
 	priv->spi->mode = spi->mode;
 	priv->spi->bits_per_word = spi->bits_per_word;
 
-	ret = mux_control_select(priv->mux, spi->chip_select);
-	if (ret)
-		return ret;
-
 	priv->current_cs = spi->chip_select;
 
 	return 0;
Signature · 1 line
2.20.1
maintainer
#1 lore raw
Quoted 9 lines · Peter Rosin

It is not valid to cache/short out selection of the mux.

mux_control_select() only locks the mux until mux_control_deselect() is called. mux_control_deselect() may put the mux in some low power state or some other user of the mux might select it for other purposes. These things are probably not happening in the original setting where this driver was developed, but it is said to be a generic SPI mux.

[...]

Applied to

https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git for-next

Thanks!

[1/1] spi: mux: repair mux usage

      commit: a2b02e4623fb127fa65a13e4ac5aa56e4ae16291

All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying to this mail.

Thanks,
Mark

Tested-by on v1 1/1
#2 lore raw
In reply to Peter Rosin
Quoted 33 lines · Peter Rosin

It is not valid to cache/short out selection of the mux.

mux_control_select() only locks the mux until mux_control_deselect() is called. mux_control_deselect() may put the mux in some low power state or some other user of the mux might select it for other purposes. These things are probably not happening in the original setting where this driver was developed, but it is said to be a generic SPI mux.

Also, the mux framework will short out the actual low level muxing operation when/if that is possible.

Fixes e9e40543ad5b ("spi: Add generic SPI multiplexer")
---
  drivers/spi/spi-mux.c | 8 ++++----
  1 file changed, 4 insertions(+), 4 deletions(-)
drivers/spi/spi-mux.c +4 -0
index 4f94c9127fc1..cc9ef371db14 100644
@@ -51,6 +51,10 @@ static int spi_mux_select(struct spi_device *spi)
  	struct spi_mux_priv *priv = spi_controller_get_devdata(spi->controller);
  	int ret;
 
+	ret = mux_control_select(priv->mux, spi->chip_select);
+	if (ret)
+		return ret;
+
  	if (priv->current_cs == spi->chip_select)
  		return 0;
 

drivers/spi/spi-mux.c static int spi_mux_select(struct spi_device *spi) · line 71

Quoted 10 lines
drivers/spi/spi-mux.c +0 -4
@@ -62,10 +66,6 @@ static int spi_mux_select(struct spi_device *spi)
  	priv->spi->mode = spi->mode;
  	priv->spi->bits_per_word = spi->bits_per_word;
 
-	ret = mux_control_select(priv->mux, spi->chip_select);
-	if (ret)
-		return ret;
-
  	priv->current_cs = spi->chip_select;
 
  	return 0;

I've tested this on the 2 hardware platforms I have with the multiplexed CS and both work fine with this change so