Skip to contentSkip to conversation

8e35bb07eb mkimage: Support automatic creating of a FIT without a .its

DISCUSSION Wolfgang Denk 2 participants 2 messages May 25, 2020 – May 27, 2020

lore
Share & tools
lore
#0 lore raw

Hi Simon,

your commit 8e35bb07eb (2016-03-14) "mkimage: Support automatic creating of a FIT without a .its" added the "-f auto" option to mkimage. While convenient in many situation, I had to notice that with "-f auto" there is no checksum information included with any of the blobs stored in the FIT image.

I guess the rationale was that the primary use case for this was to generate combinations of a U-Boot image with several device tree blobs to be used / selected by the SPL, as one can see for example in scripts/Makefile.spl :

MKIMAGEFLAGS_$(SPL_BIN).multidtb.fit = -f auto -A $(ARCH) -T firmware -C none -O u-boot \
        -n "Multi DTB fit image for $(SPL_BIN)" -E \
        $(patsubst %,-b %,$(SHRUNK_ARCH_DTB))

And - at least at that time - most implementations of the SPL did not need/want checksum verification.

However I'm asking myself if this is not an unfortunate choice. It is trivial for a not-checksum-enabled SPL to ignore any checksum in the image, but not the other way round: if there is no checksum in the images, the SPL will never be able to verify one.

Would it not be a more reasonable default for operation unter the "-f auto" flag to enable at least simple checksumming, say by auto-adding something like

	hash-1 {
		algo = "crc32";
	};

to the generated descriptions?

Best regards,

Wolfgang Denk

Signature · 5 lines
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
"It is better to have tried and failed than to have  failed  to  try,
but the result's the same."                           - Mike Dennison
#1 lore raw

Hi Wolfgang,

Quoted 32 lines · Wolfgang Denk

Hi Simon,

your commit 8e35bb07eb (2016-03-14) "mkimage: Support automatic creating of a FIT without a .its" added the "-f auto" option to mkimage. While convenient in many situation, I had to notice that with "-f auto" there is no checksum information included with any of the blobs stored in the FIT image.

I guess the rationale was that the primary use case for this was to generate combinations of a U-Boot image with several device tree blobs to be used / selected by the SPL, as one can see for example in scripts/Makefile.spl :

MKIMAGEFLAGS_$(SPL_BIN).multidtb.fit = -f auto -A $(ARCH) -T firmware -C none -O u-boot \
        -n "Multi DTB fit image for $(SPL_BIN)" -E \
        $(patsubst %,-b %,$(SHRUNK_ARCH_DTB))

And - at least at that time - most implementations of the SPL did not need/want checksum verification.

However I'm asking myself if this is not an unfortunate choice. It is trivial for a not-checksum-enabled SPL to ignore any checksum in the image, but not the other way round: if there is no checksum in the images, the SPL will never be able to verify one.

Would it not be a more reasonable default for operation unter the "-f auto" flag to enable at least simple checksumming, say by auto-adding something like

Quoted 5 lines
        hash-1 {
                algo = "crc32";
        };

to the generated descriptions?

Yes it should be easy to add that. I'll take a look.

Regards,
Simon