Skip to contentSkip to conversation

usb: typec: mux: intel_pmc_mux: Fix DP alternate mode entry

PATCH In review Heikki Krogerus 2 participants 2 messages May 29, 2020

Subsystems (3)
lore
Share & tools
lore

Heikki Krogerus

author maintainer
#0 lore raw

PATCH 1/1 usb: typec: mux: intel_pmc_mux: Fix DP alternate mode entry

The PMC needs to be notified separately about HPD (hotplug detected) signal being high after mode entry. There is a bit "HPD High" in the Alternate Mode Request that the driver already sets, but that bit is only valid when the DisplayPort Alternate Mode is directly entered from disconnected state.

Fixes 5c4edcdbcd97 ("usb: typec: mux: intel: Fix DP_HPD_LVL bit field")
---
 drivers/usb/typec/mux/intel_pmc_mux.c | 13 +++++++++++--
 1 file changed, 11 insertions(+), 2 deletions(-)
drivers/usb/typec/mux/intel_pmc_mux.c +11 -2
index 962bc69a6a59e..70ddc9d6d49e4 100644
@@ -148,7 +148,8 @@ pmc_usb_mux_dp_hpd(struct pmc_usb_port *port, struct typec_mux_state *state)
 	msg[0] = PMC_USB_DP_HPD;
 	msg[0] |= port->usb3_port << PMC_USB_MSG_USB3_PORT_SHIFT;
 
-	msg[1] = PMC_USB_DP_HPD_IRQ;
+	if (data->status & DP_STATUS_IRQ_HPD)
+		msg[1] = PMC_USB_DP_HPD_IRQ;
 
 	if (data->status & DP_STATUS_HPD_STATE)
 		msg[1] |= PMC_USB_DP_HPD_LVL;
@@ -161,6 +162,7 @@ pmc_usb_mux_dp(struct pmc_usb_port *port, struct typec_mux_state *state)
 {
 	struct typec_displayport_data *data = state->data;
 	struct altmode_req req = { };
+	int ret;
 
 	if (data->status & DP_STATUS_IRQ_HPD)
 		return pmc_usb_mux_dp_hpd(port, state);
@@ -181,7 +183,14 @@ pmc_usb_mux_dp(struct pmc_usb_port *port, struct typec_mux_state *state)
 	if (data->status & DP_STATUS_HPD_STATE)
 		req.mode_data |= PMC_USB_ALTMODE_HPD_HIGH;
 
-	return pmc_usb_command(port, (void *)&req, sizeof(req));
+	ret = pmc_usb_command(port, (void *)&req, sizeof(req));
+	if (ret)
+		return ret;
+
+	if (data->status & DP_STATUS_HPD_STATE)
+		return pmc_usb_mux_dp_hpd(port, state);
+
+	return 0;
 }
 
 static int
Signature · 1 line
2.26.2
Tested-by on v1 1/1
#1 lore raw

Hi Heikki,

Quoted 9 lines · Heikki Krogerus

The PMC needs to be notified separately about HPD (hotplug detected) signal being high after mode entry. There is a bit "HPD High" in the Alternate Mode Request that the driver already sets, but that bit is only valid when the DisplayPort Alternate Mode is directly entered from disconnected state.

Fixes 5c4edcdbcd97 ("usb: typec: mux: intel: Fix DP_HPD_LVL bit field")

Tried this out; my DP monitor seems to enumerate correctly, so:

Quoted 45 lines
---
 drivers/usb/typec/mux/intel_pmc_mux.c | 13 +++++++++++--
 1 file changed, 11 insertions(+), 2 deletions(-)
drivers/usb/typec/mux/intel_pmc_mux.c +11 -2
index 962bc69a6a59e..70ddc9d6d49e4 100644
@@ -148,7 +148,8 @@ pmc_usb_mux_dp_hpd(struct pmc_usb_port *port, struct typec_mux_state *state)
 	msg[0] = PMC_USB_DP_HPD;
 	msg[0] |= port->usb3_port << PMC_USB_MSG_USB3_PORT_SHIFT;
 
-	msg[1] = PMC_USB_DP_HPD_IRQ;
+	if (data->status & DP_STATUS_IRQ_HPD)
+		msg[1] = PMC_USB_DP_HPD_IRQ;
 
 	if (data->status & DP_STATUS_HPD_STATE)
 		msg[1] |= PMC_USB_DP_HPD_LVL;
@@ -161,6 +162,7 @@ pmc_usb_mux_dp(struct pmc_usb_port *port, struct typec_mux_state *state)
 {
 	struct typec_displayport_data *data = state->data;
 	struct altmode_req req = { };
+	int ret;
 
 	if (data->status & DP_STATUS_IRQ_HPD)
 		return pmc_usb_mux_dp_hpd(port, state);
@@ -181,7 +183,14 @@ pmc_usb_mux_dp(struct pmc_usb_port *port, struct typec_mux_state *state)
 	if (data->status & DP_STATUS_HPD_STATE)
 		req.mode_data |= PMC_USB_ALTMODE_HPD_HIGH;
 
-	return pmc_usb_command(port, (void *)&req, sizeof(req));
+	ret = pmc_usb_command(port, (void *)&req, sizeof(req));
+	if (ret)
+		return ret;
+
+	if (data->status & DP_STATUS_HPD_STATE)
+		return pmc_usb_mux_dp_hpd(port, state);
+
+	return 0;
 }
 
 static int
Signature · 1 line
2.26.2