iio: accel: mxc4005: add support for mxc6655
PATCH 1/1 iio: accel: mxc4005: add support for mxc6655
The mxc6655 is fully working with the existing mxc4005 driver. Add support for it.
--- drivers/iio/accel/mxc4005.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/iio/accel/mxc4005.c +2 -0
@@ -474,12 +474,14 @@ static int mxc4005_probe(struct i2c_client *client,static const struct acpi_device_id mxc4005_acpi_match[] = { {"MXC4005" ,0 }, + {"MXC6655" ,0 }, { }, };MODULE_DEVICE_TABLE (acpi, mxc4005_acpi_match);static const struct i2c_device_id mxc4005_id[] = { {"mxc4005" ,0 }, + {"mxc6655" ,0 }, { }, };MODULE_DEVICE_TABLE (i2c, mxc4005_id);
Signature · 1 line
2.26.2
Jonathan Cameron
maintainerQuoted 4 lines · On Fri, 29 May 2020 22:05:49 +0200 Christian Oder <[email protected]> wrote:
The mxc6655 is fully working with the existing mxc4005 driver. Add support for it.
Signed-off-by Christian Oder <[email protected]>
One query on ACPI bindings. What is there already may be missleading :(
drivers/iio/accel/mxc4005.c static int mxc4005_probe(struct i2c_client *client, · line 477
Quoted 13 lines
--- drivers/iio/accel/mxc4005.c | 2 ++ 1 file changed, 2 insertions(+)drivers/iio/accel/mxc4005.c +1
-0@@ -474,12 +474,14 @@ static int mxc4005_probe(struct i2c_client *client,static const struct acpi_device_id mxc4005_acpi_match[] = { {"MXC4005" ,0 }, + {"MXC6655" ,0 },
Do we have a reference for these ACPI bindings? While they may seem obvious, memsic don't have a registered PNP or ACPI ID that I can find. If these are in the wild (i.e. in shipping firmware) then we can take them as defacto bindings, otherwise we should avoid making them so by putting them in the driver.
Quite a few similar bindings got in a while back that I should have noticed, but I wasn't so familiar with ACPI back then. Some scrubbing of these has gone on recently, but there are lots still left in IIO.
If we aren't sure, then drop the ACPI addition and just leave the i2c one below. Adding an explicit DT binding table would also be good if that is method you are using to probe this (or PRP0001 from acpi which uses the dt bindings table)
Thanks,
Jonathan
Quoted 10 lines
drivers/iio/accel/mxc4005.c +1
-0{ }, };MODULE_DEVICE_TABLE (acpi, mxc4005_acpi_match);static const struct i2c_device_id mxc4005_id[] = { {"mxc4005" ,0 }, + {"mxc6655" ,0 }, { }, };MODULE_DEVICE_TABLE (i2c, mxc4005_id);
Hi Jonathan,
I tested the sensor on a Chuwi Hi10 X and only went by what I've seen in other commits before[1].
I just ran another test to see what entry is necessary and it appears the sensor still works when removing the i2c entry, but is not working anymore when removing the ACPI match. I got the ACPI IDs from udevadm info -e[2]. Would that mean, that I should remove the i2c entry given it's working fine with ACPI on its own then, or am I missing something?
I'm also successfully using the ACPI ID for the touchscreen orientation quirk in systemd[3].
Quoted 3 lines
Adding an explicit DT binding table would also be good if that is method you are using to probe this (or PRP0001 from acpi which uses the dt bindings table)
Frankly, I have no idea how to do that or if that would still be required when using ACPI. Can you point me in a rough direction in case it's still needed?
Regards,
Christian
---
[2]
P: /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:22/MXC6655:00
L: 0
E: DEVPATH=/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:22/MXC6655:00
E: SUBSYSTEM=acpi
E: MODALIAS=acpi:MXC6655:MXC6655:
E: USEC_INITIALIZED=5319671
E: ID_VENDOR_FROM_DATABASE=The Linux Foundation
P: /devices/pci0000:00/0000:00:16.0/i2c_designware.0/i2c-0/i2c-MXC6655:00
L: 0
E: DEVPATH=/devices/pci0000:00/0000:00:16.0/i2c_designware.0/i2c-0/i2c-MXC6655:00
E: SUBSYSTEM=i2c
E: MODALIAS=acpi:MXC6655:MXC6655:
[3]
https://github.com/systemd/systemd/commit/5e0676c2cad60b1ea029b9bfb9737e1967abb93a
Quoted 59 lines · Jonathan Cameron
Quoted 4 lines · On Fri, 29 May 2020 22:05:49 +0200 Christian Oder <[email protected]> wrote:
The mxc6655 is fully working with the existing mxc4005 driver. Add support for it.
Signed-off-by Christian Oder <[email protected]>One query on ACPI bindings. What is there already may be missleading :(
drivers/iio/accel/mxc4005.c static int mxc4005_probe(struct i2c_client *client, · line 477
Quoted 13 lines
--- drivers/iio/accel/mxc4005.c | 2 ++ 1 file changed, 2 insertions(+)drivers/iio/accel/mxc4005.c +1
-0@@ -474,12 +474,14 @@ static int mxc4005_probe(struct i2c_client *client,static const struct acpi_device_id mxc4005_acpi_match[] = { {"MXC4005" ,0 }, + {"MXC6655" ,0 },Do we have a reference for these ACPI bindings? While they may seem obvious, memsic don't have a registered PNP or ACPI ID that I can find. If these are in the wild (i.e. in shipping firmware) then we can take them as defacto bindings, otherwise we should avoid making them so by putting them in the driver.
Quite a few similar bindings got in a while back that I should have noticed, but I wasn't so familiar with ACPI back then. Some scrubbing of these has gone on recently, but there are lots still left in IIO.
If we aren't sure, then drop the ACPI addition and just leave the i2c one below. Adding an explicit DT binding table would also be good if that is method you are using to probe this (or PRP0001 from acpi which uses the dt bindings table)
Thanks,
Jonathan
Quoted 10 lines
drivers/iio/accel/mxc4005.c +1
-0{ }, };MODULE_DEVICE_TABLE (acpi, mxc4005_acpi_match);static const struct i2c_device_id mxc4005_id[] = { {"mxc4005" ,0 }, + {"mxc6655" ,0 }, { }, };MODULE_DEVICE_TABLE (i2c, mxc4005_id);
Jonathan Cameron
maintainerQuoted 10 lines · On Sun, 31 May 2020 15:16:00 +0200 Christian Oder <[email protected]> wrote:
Hi Jonathan,
I tested the sensor on a Chuwi Hi10 X and only went by what I've seen in other commits before[1].
I just ran another test to see what entry is necessary and it appears the sensor still works when removing the i2c entry, but is not working anymore when removing the ACPI match. I got the ACPI IDs from udevadm info -e[2]. Would that mean, that I should remove the i2c entry given it's working fine with ACPI on its own then, or am I missing something?
The i2c entry is fine.
Quoted 3 lines
I'm also successfully using the ACPI ID for the touchscreen orientation quirk in systemd[3].
Great. That means it is out there so is a defacto binding even if there isn't an official Doc. Sadly a lot of device manufacturers don't do this stuff the way they are supposed to!
Quoted 7 lines
Quoted 4 lines
Adding an explicit DT binding table would also be good if that is method you are using to probe this (or PRP0001 from acpi which uses the dt bindings table)
Frankly, I have no idea how to do that or if that would still be required when using ACPI. Can you point me in a rough direction in case it's still needed?
It's all good given you've confirmed the ID is out there in the wild.
Applied to the togreg branch of iio.git and pushed out as testing for autobuilders to poke at.
Note we've missed the merge window now so this will take a while to get into the mainline kernel - should be in linux-next in a few weeks though.
Thanks,
Jonathan
Quoted 87 lines
Regards,
Christian---
[2]
P: /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:22/MXC6655:00
L: 0
E: DEVPATH=/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:22/MXC6655:00
E: SUBSYSTEM=acpi
E: MODALIAS=acpi:MXC6655:MXC6655:
E: USEC_INITIALIZED=5319671
E: ID_VENDOR_FROM_DATABASE=The Linux FoundationP: /devices/pci0000:00/0000:00:16.0/i2c_designware.0/i2c-0/i2c-MXC6655:00
L: 0
E: DEVPATH=/devices/pci0000:00/0000:00:16.0/i2c_designware.0/i2c-0/i2c-MXC6655:00
E: SUBSYSTEM=i2c
E: MODALIAS=acpi:MXC6655:MXC6655:[3]
https://github.com/systemd/systemd/commit/5e0676c2cad60b1ea029b9bfb9737e1967abb93aQuoted 59 lines · Jonathan Cameron
Quoted 4 lines · On Fri, 29 May 2020 22:05:49 +0200 Christian Oder <[email protected]> wrote:
The mxc6655 is fully working with the existing mxc4005 driver. Add support for it.
Signed-off-by Christian Oder <[email protected]>One query on ACPI bindings. What is there already may be missleading :(
drivers/iio/accel/mxc4005.c static int mxc4005_probe(struct i2c_client *client, · line 477
Quoted 13 lines
--- drivers/iio/accel/mxc4005.c | 2 ++ 1 file changed, 2 insertions(+)drivers/iio/accel/mxc4005.c +1
-0@@ -474,12 +474,14 @@ static int mxc4005_probe(struct i2c_client *client,static const struct acpi_device_id mxc4005_acpi_match[] = { {"MXC4005" ,0 }, + {"MXC6655" ,0 },Do we have a reference for these ACPI bindings? While they may seem obvious, memsic don't have a registered PNP or ACPI ID that I can find. If these are in the wild (i.e. in shipping firmware) then we can take them as defacto bindings, otherwise we should avoid making them so by putting them in the driver.
Quite a few similar bindings got in a while back that I should have noticed, but I wasn't so familiar with ACPI back then. Some scrubbing of these has gone on recently, but there are lots still left in IIO.
If we aren't sure, then drop the ACPI addition and just leave the i2c one below. Adding an explicit DT binding table would also be good if that is method you are using to probe this (or PRP0001 from acpi which uses the dt bindings table)
Thanks,
Jonathan
Quoted 10 lines
drivers/iio/accel/mxc4005.c +1
-0{ }, };MODULE_DEVICE_TABLE (acpi, mxc4005_acpi_match);static const struct i2c_device_id mxc4005_id[] = { {"mxc4005" ,0 }, + {"mxc6655" ,0 }, { }, };MODULE_DEVICE_TABLE (i2c, mxc4005_id);