Skip to contentSkip to conversation

board: amlogic: add Odroid C4 support

PATCH New Neil Armstrong 2 participants 8 messages Jul 1, 2020 – Jul 7, 2020

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

cover board: amlogic: add Odroid C4 support

This patchset adds support for the Hardkernel Odroid-C4 board based on an Amlogic S905X3 SoC (SM1).

These patches were made very early from Christian Hewitt when the device was unveiled by Hardkernel, and superseed the patchset from Beniamino Galvani posted later.

Beniamino, sorry for posting this over your patchset, but they are essentially the same and this one is already used by LibreELEC, Armbian and out KernelCI boards.

It used the new Odroid-N2 board support instead of W400, and adds a doc file in RsT format.

Christian Hewitt (2):
ARM: dts: sync amlogic G12A/G12B/SM1 DT from Linux 5.8-rc1
boards: amlogic: add Odroid C4 support

Neil Armstrong (1):
ARM: dts: meson-sm1-odroid-c4: add ethernet PHY reset

 arch/arm/dts/Makefile                        |   1 +
 arch/arm/dts/meson-g12-common.dtsi           |  13 +-
 arch/arm/dts/meson-g12.dtsi                  |  32 +-
 arch/arm/dts/meson-g12b-khadas-vim3.dtsi     |  22 +-
 arch/arm/dts/meson-g12b-s922x.dtsi           |  15 +
 arch/arm/dts/meson-g12b.dtsi                 |  22 +
 arch/arm/dts/meson-khadas-vim3.dtsi          |   4 +-
 arch/arm/dts/meson-sm1-odroid-c4-u-boot.dtsi |  13 +
 arch/arm/dts/meson-sm1-odroid-c4.dts         | 402 +++++++++++++++++++
 arch/arm/dts/meson-sm1-sei610.dts            |   2 +-
 arch/arm/dts/meson-sm1.dtsi                  |  24 ++
 board/amlogic/odroid-n2/MAINTAINERS          |   2 +
 configs/odroid-c4_defconfig                  |  62 +++
 doc/board/amlogic/index.rst                  |   3 +-
 doc/board/amlogic/odroid-c4.rst              | 133 ++++++
 15 files changed, 713 insertions(+), 37 deletions(-)
 create mode 100644 arch/arm/dts/meson-sm1-odroid-c4-u-boot.dtsi
 create mode 100644 arch/arm/dts/meson-sm1-odroid-c4.dts
 create mode 100644 configs/odroid-c4_defconfig
 create mode 100644 doc/board/amlogic/odroid-c4.rst
Signature · 1 line
2.22.0
#1 lore raw

PATCH 1/3 ARM: dts: sync amlogic G12A/G12B/SM1 DT from Linux 5.8-rc1

From: Christian Hewitt <[email protected]>

This imports the changes and the new Odroid-C4 board from the Linux commit b3a9e3b9622a ("Linux 5.8-rc1").

---
 arch/arm/dts/Makefile                    |   1 +
 arch/arm/dts/meson-g12-common.dtsi       |  13 +-
 arch/arm/dts/meson-g12.dtsi              |  32 +-
 arch/arm/dts/meson-g12b-khadas-vim3.dtsi |  22 +-
 arch/arm/dts/meson-g12b-s922x.dtsi       |  15 +
 arch/arm/dts/meson-g12b.dtsi             |  22 ++
 arch/arm/dts/meson-khadas-vim3.dtsi      |   4 +-
 arch/arm/dts/meson-sm1-odroid-c4.dts     | 402 +++++++++++++++++++++++
 arch/arm/dts/meson-sm1-sei610.dts        |   2 +-
 arch/arm/dts/meson-sm1.dtsi              |  24 ++
 10 files changed, 501 insertions(+), 36 deletions(-)
 create mode 100644 arch/arm/dts/meson-sm1-odroid-c4.dts
arch/arm/dts/Makefile +1 -0
index 9900b44274..b7c2754010 100644
@@ -161,6 +161,7 @@ dtb-$(CONFIG_ARCH_MESON) += \
 	meson-g12b-odroid-n2.dtb \
 	meson-g12b-a311d-khadas-vim3.dtb \
 	meson-sm1-khadas-vim3l.dtb \
+	meson-sm1-odroid-c4.dtb \
 	meson-sm1-sei610.dtb
 dtb-$(CONFIG_ARCH_TEGRA) += tegra20-harmony.dtb \
 	tegra20-medcom-wide.dtb \
arch/arm/dts/meson-g12-common.dtsi +12 -1
index 0882ea215b..593a006f4b 100644
@@ -250,6 +250,17 @@
 				};
 			};
 
+			acodec: audio-controller at 32000 {
+				compatible = "amlogic,t9015";
+				reg = <0x0 0x32000 0x0 0x14>;
+				#sound-dai-cells = <0>;
+				sound-name-prefix = "ACODEC";
+				clocks = <&clkc CLKID_AUDIO_CODEC>;
+				clock-names = "pclk";
+				resets = <&reset RESET_AUDIO_CODEC>;
+				status = "disabled";
+			};
+
 			periphs: bus at 34400 {
 				compatible = "simple-bus";
 				reg = <0x0 0x34400 0x0 0x400>;
@@ -2319,7 +2330,7 @@
 				reg = <0x0 0xff400000 0x0 0x40000>;
 				interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clkc CLKID_USB1_DDR_BRIDGE>;
-				clock-names = "ddr";
+				clock-names = "otg";
 				phys = <&usb2_phy1>;
 				phy-names = "usb2-phy";
 				dr_mode = "peripheral";
arch/arm/dts/meson-g12.dtsi +9 -23
index 55d39020ec..6a1f4dcf64 100644
@@ -343,6 +343,15 @@
 			status = "disabled";
 		};
 
+		toacodec: audio-controller at 740 {
+			compatible = "amlogic,g12a-toacodec";
+			reg = <0x0 0x740 0x0 0x4>;
+			#sound-dai-cells = <1>;
+			sound-name-prefix = "TOACODEC";
+			resets = <&clkc_audio AUD_RESET_TOACODEC>;
+			status = "disabled";
+		};
+
 		tohdmitx: audio-controller at 744 {
 			compatible = "amlogic,g12a-tohdmitx";
 			reg = <0x0 0x744 0x0 0x4>;
@@ -354,29 +363,6 @@
 	};
 };
 
-&cpu_thermal {
-	cooling-maps {
-		map0 {
-			trip = <&cpu_passive>;
-			cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-					 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-					 <&cpu100 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-					 <&cpu101 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-					 <&cpu102 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-					 <&cpu103 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-		};
-		map1 {
-			trip = <&cpu_hot>;
-			cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-					 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-					 <&cpu100 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-					 <&cpu101 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-					 <&cpu102 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-					 <&cpu103 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-		};
-	};
-};
-
 &ethmac {
 	power-domains = <&pwrc PWRC_G12A_ETH_ID>;
 };
arch/arm/dts/meson-g12b-khadas-vim3.dtsi +13 -9
index c33e85fbda..224c890d32 100644
@@ -51,11 +51,11 @@
 	sound {
 		compatible = "amlogic,axg-sound-card";
 		model = "G12B-KHADAS-VIM3";
-		audio-aux-devs = <&tdmout_b>;
-		audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
-				"TDMOUT_B IN 1", "FRDDR_B OUT 1",
-				"TDMOUT_B IN 2", "FRDDR_C OUT 1",
-				"TDM_B Playback", "TDMOUT_B OUT";
+		audio-aux-devs = <&tdmout_a>;
+		audio-routing = "TDMOUT_A IN 0", "FRDDR_A OUT 0",
+				"TDMOUT_A IN 1", "FRDDR_B OUT 0",
+				"TDMOUT_A IN 2", "FRDDR_C OUT 0",
+				"TDM_A Playback", "TDMOUT_A OUT";
 
 		assigned-clocks = <&clkc CLKID_MPLL2>,
 				  <&clkc CLKID_MPLL0>,
@@ -80,7 +80,7 @@
 
 		/* 8ch hdmi interface */
 		dai-link-3 {
-			sound-dai = <&tdmif_b>;
+			sound-dai = <&tdmif_a>;
 			dai-format = "i2s";
 			dai-tdm-slot-tx-mask-0 = <1 1>;
 			dai-tdm-slot-tx-mask-1 = <1 1>;
@@ -89,7 +89,7 @@
 			mclk-fs = <256>;
 
 			codec {
-				sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
+				sound-dai = <&tohdmitx TOHDMITX_I2S_IN_A>;
 			};
 		};
 
@@ -154,6 +154,10 @@
 	clock-latency = <50000>;
 };
 
+&frddr_a {
+	status = "okay";
+};
+
 &frddr_b {
 	status = "okay";
 };
@@ -178,11 +182,11 @@
 	status = "okay";
 };
 
-&tdmif_b {
+&tdmif_a {
 	status = "okay";
 };
 
-&tdmout_b {
+&tdmout_a {
 	status = "okay";
 };
 
arch/arm/dts/meson-g12b-s922x.dtsi +15 -0
index 046cc332d0..1e5d0ee5d5 100644
@@ -65,6 +65,11 @@
 			opp-hz = /bits/ 64 <1896000000>;
 			opp-microvolt = <981000>;
 		};
+
+		opp-1992000000 {
+			opp-hz = /bits/ 64 <1992000000>;
+			opp-microvolt = <1001000>;
+		};
 	};
 
 	cpub_opp_table_1: opp-table-1 {
@@ -120,5 +125,15 @@
 			opp-hz = /bits/ 64 <1704000000>;
 			opp-microvolt = <891000>;
 		};
+
+		opp-1800000000 {
+			opp-hz = /bits/ 64 <1800000000>;
+			opp-microvolt = <981000>;
+		};
+
+		opp-1908000000 {
+			opp-hz = /bits/ 64 <1908000000>;
+			opp-microvolt = <1022000>;
+		};
 	};
 };
arch/arm/dts/meson-g12b.dtsi +22 -0
index 6dbc396804..9b8548e5f6 100644
@@ -113,3 +113,25 @@
 	compatible = "amlogic,g12b-clkc";
 };
 
+&cpu_thermal {
+	cooling-maps {
+		map0 {
+			trip = <&cpu_passive>;
+			cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					 <&cpu100 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					 <&cpu101 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					 <&cpu102 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					 <&cpu103 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+		};
+		map1 {
+			trip = <&cpu_hot>;
+			cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					 <&cpu100 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					 <&cpu101 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					 <&cpu102 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					 <&cpu103 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+		};
+	};
+};
arch/arm/dts/meson-khadas-vim3.dtsi +2 -2
index 094ecf2222..1ef1e3672b 100644
@@ -39,13 +39,13 @@
 	leds {
 		compatible = "gpio-leds";
 
-		white {
+		led-white {
 			label = "vim3:white:sys";
 			gpios = <&gpio_ao GPIOAO_4 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "heartbeat";
 		};
 
-		red {
+		led-red {
 			label = "vim3:red";
 			gpios = <&gpio_expander 5 GPIO_ACTIVE_LOW>;
 		};
arch/arm/dts/meson-sm1-odroid-c4.dts new file +402 -0

402 lines not on this page · raw message

arch/arm/dts/meson-sm1-sei610.dts +1 -1
index dfb2438851..5ab139a34c 100644
@@ -104,7 +104,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		bluetooth {
+		led-bluetooth {
 			label = "sei610:blue:bt";
 			gpios = <&gpio GPIOC_7 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
 			default-state = "off";
arch/arm/dts/meson-sm1.dtsi +24 -0
index d4ec735fb1..71317f5aad 100644
@@ -56,6 +56,7 @@
 			reg = <0x0 0x0>;
 			enable-method = "psci";
 			next-level-cache = <&l2>;
+			#cooling-cells = <2>;
 		};
 
 		cpu1: cpu at 1 {
@@ -64,6 +65,7 @@
 			reg = <0x0 0x1>;
 			enable-method = "psci";
 			next-level-cache = <&l2>;
+			#cooling-cells = <2>;
 		};
 
 		cpu2: cpu at 2 {
@@ -72,6 +74,7 @@
 			reg = <0x0 0x2>;
 			enable-method = "psci";
 			next-level-cache = <&l2>;
+			#cooling-cells = <2>;
 		};
 
 		cpu3: cpu at 3 {
@@ -80,6 +83,7 @@
 			reg = <0x0 0x3>;
 			enable-method = "psci";
 			next-level-cache = <&l2>;
+			#cooling-cells = <2>;
 		};
 
 		l2: l2-cache0 {
@@ -466,6 +470,26 @@
 	compatible = "amlogic,sm1-clkc";
 };
 
+&cpu_thermal {
+	cooling-maps {
+		map0 {
+			trip = <&cpu_passive>;
+			cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+		};
+
+		map1 {
+			trip = <&cpu_hot>;
+			cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+		};
+	};
+};
+
 &ethmac {
 	power-domains = <&pwrc PWRC_SM1_ETH_ID>;
 };
Signature · 1 line
2.22.0
#2 lore raw

PATCH 1/3 ARM: dts: sync amlogic G12A/G12B/SM1 DT from Linux 5.8-rc1

Hi Neil,

Quoted 7 lines · Neil Armstrong

From: Christian Hewitt <[email protected]>

This imports the changes and the new Odroid-C4 board from the Linux commit b3a9e3b9622a ("Linux 5.8-rc1").

Please add my

Quoted 740 lines
---
 arch/arm/dts/Makefile                    |   1 +
 arch/arm/dts/meson-g12-common.dtsi       |  13 +-
 arch/arm/dts/meson-g12.dtsi              |  32 +-
 arch/arm/dts/meson-g12b-khadas-vim3.dtsi |  22 +-
 arch/arm/dts/meson-g12b-s922x.dtsi       |  15 +
 arch/arm/dts/meson-g12b.dtsi             |  22 ++
 arch/arm/dts/meson-khadas-vim3.dtsi      |   4 +-
 arch/arm/dts/meson-sm1-odroid-c4.dts     | 402 +++++++++++++++++++++++
 arch/arm/dts/meson-sm1-sei610.dts        |   2 +-
 arch/arm/dts/meson-sm1.dtsi              |  24 ++
 10 files changed, 501 insertions(+), 36 deletions(-)
 create mode 100644 arch/arm/dts/meson-sm1-odroid-c4.dts
arch/arm/dts/Makefile +1 -0
index 9900b44274..b7c2754010 100644
@@ -161,6 +161,7 @@ dtb-$(CONFIG_ARCH_MESON) += \
        meson-g12b-odroid-n2.dtb \
        meson-g12b-a311d-khadas-vim3.dtb \
        meson-sm1-khadas-vim3l.dtb \
+       meson-sm1-odroid-c4.dtb \
        meson-sm1-sei610.dtb
 dtb-$(CONFIG_ARCH_TEGRA) += tegra20-harmony.dtb \
        tegra20-medcom-wide.dtb \
arch/arm/dts/meson-g12-common.dtsi +12 -1
index 0882ea215b..593a006f4b 100644
@@ -250,6 +250,17 @@
                                };
                        };
 
+                       acodec: audio-controller at 32000 {
+                               compatible = "amlogic,t9015";
+                               reg = <0x0 0x32000 0x0 0x14>;
+                               #sound-dai-cells = <0>;
+                               sound-name-prefix = "ACODEC";
+                               clocks = <&clkc CLKID_AUDIO_CODEC>;
+                               clock-names = "pclk";
+                               resets = <&reset RESET_AUDIO_CODEC>;
+                               status = "disabled";
+                       };
+
                        periphs: bus at 34400 {
                                compatible = "simple-bus";
                                reg = <0x0 0x34400 0x0 0x400>;
@@ -2319,7 +2330,7 @@
                                reg = <0x0 0xff400000 0x0 0x40000>;
                                interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
                                clocks = <&clkc CLKID_USB1_DDR_BRIDGE>;
-                               clock-names = "ddr";
+                               clock-names = "otg";
                                phys = <&usb2_phy1>;
                                phy-names = "usb2-phy";
                                dr_mode = "peripheral";
arch/arm/dts/meson-g12.dtsi +9 -23
index 55d39020ec..6a1f4dcf64 100644
@@ -343,6 +343,15 @@
                        status = "disabled";
                };
 
+               toacodec: audio-controller at 740 {
+                       compatible = "amlogic,g12a-toacodec";
+                       reg = <0x0 0x740 0x0 0x4>;
+                       #sound-dai-cells = <1>;
+                       sound-name-prefix = "TOACODEC";
+                       resets = <&clkc_audio AUD_RESET_TOACODEC>;
+                       status = "disabled";
+               };
+
                tohdmitx: audio-controller at 744 {
                        compatible = "amlogic,g12a-tohdmitx";
                        reg = <0x0 0x744 0x0 0x4>;
@@ -354,29 +363,6 @@
        };
 };
 
-&cpu_thermal {
-       cooling-maps {
-               map0 {
-                       trip = <&cpu_passive>;
-                       cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-                                        <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-                                        <&cpu100 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-                                        <&cpu101 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-                                        <&cpu102 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-                                        <&cpu103 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-               };
-               map1 {
-                       trip = <&cpu_hot>;
-                       cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-                                        <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-                                        <&cpu100 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-                                        <&cpu101 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-                                        <&cpu102 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-                                        <&cpu103 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-               };
-       };
-};
-
 &ethmac {
        power-domains = <&pwrc PWRC_G12A_ETH_ID>;
 };
arch/arm/dts/meson-g12b-khadas-vim3.dtsi +13 -9
index c33e85fbda..224c890d32 100644
@@ -51,11 +51,11 @@
        sound {
                compatible = "amlogic,axg-sound-card";
                model = "G12B-KHADAS-VIM3";
-               audio-aux-devs = <&tdmout_b>;
-               audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
-                               "TDMOUT_B IN 1", "FRDDR_B OUT 1",
-                               "TDMOUT_B IN 2", "FRDDR_C OUT 1",
-                               "TDM_B Playback", "TDMOUT_B OUT";
+               audio-aux-devs = <&tdmout_a>;
+               audio-routing = "TDMOUT_A IN 0", "FRDDR_A OUT 0",
+                               "TDMOUT_A IN 1", "FRDDR_B OUT 0",
+                               "TDMOUT_A IN 2", "FRDDR_C OUT 0",
+                               "TDM_A Playback", "TDMOUT_A OUT";
 
                assigned-clocks = <&clkc CLKID_MPLL2>,
                                  <&clkc CLKID_MPLL0>,
@@ -80,7 +80,7 @@
 
                /* 8ch hdmi interface */
                dai-link-3 {
-                       sound-dai = <&tdmif_b>;
+                       sound-dai = <&tdmif_a>;
                        dai-format = "i2s";
                        dai-tdm-slot-tx-mask-0 = <1 1>;
                        dai-tdm-slot-tx-mask-1 = <1 1>;
@@ -89,7 +89,7 @@
                        mclk-fs = <256>;
 
                        codec {
-                               sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
+                               sound-dai = <&tohdmitx TOHDMITX_I2S_IN_A>;
                        };
                };
 
@@ -154,6 +154,10 @@
        clock-latency = <50000>;
 };
 
+&frddr_a {
+       status = "okay";
+};
+
 &frddr_b {
        status = "okay";
 };
@@ -178,11 +182,11 @@
        status = "okay";
 };
 
-&tdmif_b {
+&tdmif_a {
        status = "okay";
 };
 
-&tdmout_b {
+&tdmout_a {
        status = "okay";
 };
 
arch/arm/dts/meson-g12b-s922x.dtsi +15 -0
index 046cc332d0..1e5d0ee5d5 100644
@@ -65,6 +65,11 @@
                        opp-hz = /bits/ 64 <1896000000>;
                        opp-microvolt = <981000>;
                };
+
+               opp-1992000000 {
+                       opp-hz = /bits/ 64 <1992000000>;
+                       opp-microvolt = <1001000>;
+               };
        };
 
        cpub_opp_table_1: opp-table-1 {
@@ -120,5 +125,15 @@
                        opp-hz = /bits/ 64 <1704000000>;
                        opp-microvolt = <891000>;
                };
+
+               opp-1800000000 {
+                       opp-hz = /bits/ 64 <1800000000>;
+                       opp-microvolt = <981000>;
+               };
+
+               opp-1908000000 {
+                       opp-hz = /bits/ 64 <1908000000>;
+                       opp-microvolt = <1022000>;
+               };
        };
 };
arch/arm/dts/meson-g12b.dtsi +22 -0
index 6dbc396804..9b8548e5f6 100644
@@ -113,3 +113,25 @@
        compatible = "amlogic,g12b-clkc";
 };
 
+&cpu_thermal {
+       cooling-maps {
+               map0 {
+                       trip = <&cpu_passive>;
+                       cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+                                        <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+                                        <&cpu100 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+                                        <&cpu101 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+                                        <&cpu102 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+                                        <&cpu103 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+               };
+               map1 {
+                       trip = <&cpu_hot>;
+                       cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+                                        <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+                                        <&cpu100 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+                                        <&cpu101 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+                                        <&cpu102 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+                                        <&cpu103 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+               };
+       };
+};
arch/arm/dts/meson-khadas-vim3.dtsi +2 -2
index 094ecf2222..1ef1e3672b 100644
@@ -39,13 +39,13 @@
        leds {
                compatible = "gpio-leds";
 
-               white {
+               led-white {
                        label = "vim3:white:sys";
                        gpios = <&gpio_ao GPIOAO_4 GPIO_ACTIVE_LOW>;
                        linux,default-trigger = "heartbeat";
                };
 
-               red {
+               led-red {
                        label = "vim3:red";
                        gpios = <&gpio_expander 5 GPIO_ACTIVE_LOW>;
                };
arch/arm/dts/meson-sm1-odroid-c4.dts new file +402 -0
new file mode 100644
index 0000000000..00d90b30f8
@@ -0,0 +1,402 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 Dongjin Kim <[email protected]>
+ */
+
+/dts-v1/;
+
+#include "meson-sm1.dtsi"
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+       compatible = "hardkernel,odroid-c4", "amlogic,sm1";
+       model = "Hardkernel ODROID-C4";
+
+       aliases {
+               serial0 = &uart_AO;
+               ethernet0 = &ethmac;
+       };
+
+       chosen {
+               stdout-path = "serial0:115200n8";
+       };
+
+       memory at 0 {
+               device_type = "memory";
+               reg = <0x0 0x0 0x0 0x40000000>;
+       };
+
+       emmc_pwrseq: emmc-pwrseq {
+               compatible = "mmc-pwrseq-emmc";
+               reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
+       };
+
+       leds {
+               compatible = "gpio-leds";
+
+               led-blue {
+                       color = <LED_COLOR_ID_BLUE>;
+                       function = LED_FUNCTION_STATUS;
+                       gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_HIGH>;
+                       linux,default-trigger = "heartbeat";
+                       panic-indicator;
+               };
+       };
+
+       tflash_vdd: regulator-tflash_vdd {
+               compatible = "regulator-fixed";
+
+               regulator-name = "TFLASH_VDD";
+               regulator-min-microvolt = <3300000>;
+               regulator-max-microvolt = <3300000>;
+
+               gpio = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_HIGH>;
+               enable-active-high;
+               regulator-always-on;
+       };
+
+       tf_io: gpio-regulator-tf_io {
+               compatible = "regulator-gpio";
+
+               regulator-name = "TF_IO";
+               regulator-min-microvolt = <1800000>;
+               regulator-max-microvolt = <3300000>;
+
+               gpios = <&gpio_ao GPIOAO_6 GPIO_ACTIVE_HIGH>;
+               gpios-states = <0>;
+
+               states = <3300000 0>,
+                        <1800000 1>;
+       };
+
+       flash_1v8: regulator-flash_1v8 {
+               compatible = "regulator-fixed";
+               regulator-name = "FLASH_1V8";
+               regulator-min-microvolt = <1800000>;
+               regulator-max-microvolt = <1800000>;
+               vin-supply = <&vcc_3v3>;
+               regulator-always-on;
+       };
+
+       main_12v: regulator-main_12v {
+               compatible = "regulator-fixed";
+               regulator-name = "12V";
+               regulator-min-microvolt = <12000000>;
+               regulator-max-microvolt = <12000000>;
+               regulator-always-on;
+       };
+
+       vcc_5v: regulator-vcc_5v {
+               compatible = "regulator-fixed";
+               regulator-name = "5V";
+               regulator-min-microvolt = <5000000>;
+               regulator-max-microvolt = <5000000>;
+               regulator-always-on;
+               vin-supply = <&main_12v>;
+       };
+
+       vcc_1v8: regulator-vcc_1v8 {
+               compatible = "regulator-fixed";
+               regulator-name = "VCC_1V8";
+               regulator-min-microvolt = <1800000>;
+               regulator-max-microvolt = <1800000>;
+               vin-supply = <&vcc_3v3>;
+               regulator-always-on;
+       };
+
+       vcc_3v3: regulator-vcc_3v3 {
+               compatible = "regulator-fixed";
+               regulator-name = "VCC_3V3";
+               regulator-min-microvolt = <3300000>;
+               regulator-max-microvolt = <3300000>;
+               vin-supply = <&vddao_3v3>;
+               regulator-always-on;
+               /* FIXME: actually controlled by VDDCPU_B_EN */
+       };
+
+       vddcpu: regulator-vddcpu {
+               /*
+                * MP8756GD Regulator.
+                */
+               compatible = "pwm-regulator";
+
+               regulator-name = "VDDCPU";
+               regulator-min-microvolt = <721000>;
+               regulator-max-microvolt = <1022000>;
+
+               vin-supply = <&main_12v>;
+
+               pwms = <&pwm_AO_cd 1 1250 0>;
+               pwm-dutycycle-range = <100 0>;
+
+               regulator-boot-on;
+               regulator-always-on;
+       };
+
+       hub_5v: regulator-hub_5v {
+               compatible = "regulator-fixed";
+               regulator-name = "HUB_5V";
+               regulator-min-microvolt = <5000000>;
+               regulator-max-microvolt = <5000000>;
+               vin-supply = <&vcc_5v>;
+
+               /* Connected to the Hub CHIPENABLE, LOW sets low power state */
+               gpio = <&gpio GPIOH_4 GPIO_ACTIVE_HIGH>;
+               enable-active-high;
+       };
+
+       usb_pwr_en: regulator-usb_pwr_en {
+               compatible = "regulator-fixed";
+               regulator-name = "USB_PWR_EN";
+               regulator-min-microvolt = <5000000>;
+               regulator-max-microvolt = <5000000>;
+               vin-supply = <&vcc_5v>;
+
+               /* Connected to the microUSB port power enable */
+               gpio = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_HIGH>;
+               enable-active-high;
+       };
+
+       vddao_1v8: regulator-vddao_1v8 {
+               compatible = "regulator-fixed";
+               regulator-name = "VDDAO_1V8";
+               regulator-min-microvolt = <1800000>;
+               regulator-max-microvolt = <1800000>;
+               vin-supply = <&vddao_3v3>;
+               regulator-always-on;
+       };
+
+       vddao_3v3: regulator-vddao_3v3 {
+               compatible = "regulator-fixed";
+               regulator-name = "VDDAO_3V3";
+               regulator-min-microvolt = <3300000>;
+               regulator-max-microvolt = <3300000>;
+               vin-supply = <&main_12v>;
+               regulator-always-on;
+       };
+
+       hdmi-connector {
+               compatible = "hdmi-connector";
+               type = "a";
+
+               port {
+                       hdmi_connector_in: endpoint {
+                               remote-endpoint = <&hdmi_tx_tmds_out>;
+                       };
+               };
+       };
+};
+
+&cpu0 {
+       cpu-supply = <&vddcpu>;
+       operating-points-v2 = <&cpu_opp_table>;
+       clocks = <&clkc CLKID_CPU_CLK>;
+       clock-latency = <50000>;
+};
+
+&cpu1 {
+       cpu-supply = <&vddcpu>;
+       operating-points-v2 = <&cpu_opp_table>;
+       clocks = <&clkc CLKID_CPU1_CLK>;
+       clock-latency = <50000>;
+};
+
+&cpu2 {
+       cpu-supply = <&vddcpu>;
+       operating-points-v2 = <&cpu_opp_table>;
+       clocks = <&clkc CLKID_CPU2_CLK>;
+       clock-latency = <50000>;
+};
+
+&cpu3 {
+       cpu-supply = <&vddcpu>;
+       operating-points-v2 = <&cpu_opp_table>;
+       clocks = <&clkc CLKID_CPU3_CLK>;
+       clock-latency = <50000>;
+};
+
+&ext_mdio {
+       external_phy: ethernet-phy at 0 {
+               /* Realtek RTL8211F (0x001cc916) */
+               reg = <0>;
+               max-speed = <1000>;
+
+               interrupt-parent = <&gpio_intc>;
+               /* MAC_INTR on GPIOZ_14 */
+               interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
+       };
+};
+
+&ethmac {
+       pinctrl-0 = <&eth_pins>, <&eth_rgmii_pins>;
+       pinctrl-names = "default";
+       status = "okay";
+       phy-mode = "rgmii";
+       phy-handle = <&external_phy>;
+       amlogic,tx-delay-ns = <2>;
+};
+
+&gpio {
+       gpio-line-names =
+               /* GPIOZ */
+               "", "", "", "", "", "", "", "",
+               "", "", "", "", "", "", "", "",
+               /* GPIOH */
+               "", "", "", "", "",
+               "PIN_36", /* GPIOH_5 */
+               "PIN_26", /* GPIOH_6 */
+               "PIN_32", /* GPIOH_7 */
+               "",
+               /* BOOT */
+               "", "", "", "", "", "", "", "",
+               "", "", "", "", "", "", "", "",
+               /* GPIOC */
+               "", "", "", "", "", "", "", "",
+               /* GPIOA */
+               "", "", "", "", "", "", "", "",
+               "", "", "", "", "", "",
+               "PIN_27", /* GPIOA_14 */
+               "PIN_28", /* GPIOA_15 */
+               /* GPIOX */
+               "PIN_16", /* GPIOX_0 */
+               "PIN_18", /* GPIOX_1 */
+               "PIN_22", /* GPIOX_2 */
+               "PIN_11", /* GPIOX_3 */
+               "PIN_13", /* GPIOX_4 */
+               "PIN_7",  /* GPIOX_5 */
+               "PIN_33", /* GPIOX_6 */
+               "PIN_15", /* GPIOX_7 */
+               "PIN_19", /* GPIOX_8 */
+               "PIN_21", /* GPIOX_9 */
+               "PIN_24", /* GPIOX_10 */
+               "PIN_23", /* GPIOX_11 */
+               "PIN_8",  /* GPIOX_12 */
+               "PIN_10", /* GPIOX_13 */
+               "PIN_29", /* GPIOX_14 */
+               "PIN_31", /* GPIOX_15 */
+               "PIN_12", /* GPIOX_16 */
+               "PIN_3",  /* GPIOX_17 */
+               "PIN_5",  /* GPIOX_18 */
+               "PIN_35"; /* GPIOX_19 */
+
+       /*
+        * WARNING: The USB Hub on the Odroid-C4 needs a reset signal
+        * to be turned high in order to be detected by the USB Controller
+        * This signal should be handled by a USB specific power sequence
+        * in order to reset the Hub when USB bus is powered down.
+        */
+       usb-hub {
+               gpio-hog;
+               gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>;
+               output-high;
+               line-name = "usb-hub-reset";
+       };
+};
+
+&gpio_ao {
+       gpio-line-names =
+               /* GPIOAO */
+               "", "", "", "",
+               "PIN_47", /* GPIOAO_4 */
+               "", "",
+               "PIN_45", /* GPIOAO_7 */
+               "PIN_46", /* GPIOAO_8 */
+               "PIN_44", /* GPIOAO_9 */
+               "PIN_42", /* GPIOAO_10 */
+               "",
+               /* GPIOE */
+               "", "", "";
+};
+
+&hdmi_tx {
+       status = "okay";
+       pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
+       pinctrl-names = "default";
+       hdmi-supply = <&vcc_5v>;
+};
+
+&hdmi_tx_tmds_port {
+       hdmi_tx_tmds_out: endpoint {
+               remote-endpoint = <&hdmi_connector_in>;
+       };
+};
+
+&ir {
+       status = "okay";
+       pinctrl-0 = <&remote_input_ao_pins>;
+       pinctrl-names = "default";
+       linux,rc-map-name = "rc-odroid";
+};
+
+&pwm_AO_cd {
+       pinctrl-0 = <&pwm_ao_d_e_pins>;
+       pinctrl-names = "default";
+       clocks = <&xtal>;
+       clock-names = "clkin1";
+       status = "okay";
+};
+
+&saradc {
+       status = "okay";
+};
+
+/* SD card */
+&sd_emmc_b {
+       status = "okay";
+       pinctrl-0 = <&sdcard_c_pins>;
+       pinctrl-1 = <&sdcard_clk_gate_c_pins>;
+       pinctrl-names = "default", "clk-gate";
+
+       bus-width = <4>;
+       cap-sd-highspeed;
+       max-frequency = <200000000>;
+       sd-uhs-sdr12;
+       sd-uhs-sdr25;
+       sd-uhs-sdr50;
+       sd-uhs-sdr104;
+       disable-wp;
+
+       cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+       vmmc-supply = <&tflash_vdd>;
+       vqmmc-supply = <&tf_io>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+       status = "okay";
+       pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
+       pinctrl-1 = <&emmc_clk_gate_pins>;
+       pinctrl-names = "default", "clk-gate";
+
+       bus-width = <8>;
+       cap-mmc-highspeed;
+       mmc-ddr-1_8v;
+       mmc-hs200-1_8v;
+       max-frequency = <200000000>;
+       disable-wp;
+
+       mmc-pwrseq = <&emmc_pwrseq>;
+       vmmc-supply = <&vcc_3v3>;
+       vqmmc-supply = <&flash_1v8>;
+};
+
+&uart_AO {
+       status = "okay";
+       pinctrl-0 = <&uart_ao_a_pins>;
+       pinctrl-names = "default";
+};
+
+&usb {
+       status = "okay";
+       vbus-supply = <&usb_pwr_en>;
+};
+
+&usb2_phy0 {
+       phy-supply = <&vcc_5v>;
+};
+
+&usb2_phy1 {
+       /* Enable the hub which is connected to this port */
+       phy-supply = <&hub_5v>;
+};
arch/arm/dts/meson-sm1-sei610.dts +1 -1
index dfb2438851..5ab139a34c 100644
@@ -104,7 +104,7 @@
        leds {
                compatible = "gpio-leds";
 
-               bluetooth {
+               led-bluetooth {
                        label = "sei610:blue:bt";
                        gpios = <&gpio GPIOC_7 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
                        default-state = "off";
arch/arm/dts/meson-sm1.dtsi +24 -1
index d4ec735fb1..71317f5aad 100644
@@ -56,6 +56,7 @@
                        reg = <0x0 0x0>;
                        enable-method = "psci";
                        next-level-cache = <&l2>;
+                       #cooling-cells = <2>;
                };
 
                cpu1: cpu at 1 {
@@ -64,6 +65,7 @@
                        reg = <0x0 0x1>;
                        enable-method = "psci";
                        next-level-cache = <&l2>;
+                       #cooling-cells = <2>;
                };
 
                cpu2: cpu at 2 {
@@ -72,6 +74,7 @@
                        reg = <0x0 0x2>;
                        enable-method = "psci";
                        next-level-cache = <&l2>;
+                       #cooling-cells = <2>;
                };
 
                cpu3: cpu at 3 {
@@ -80,6 +83,7 @@
                        reg = <0x0 0x3>;
                        enable-method = "psci";
                        next-level-cache = <&l2>;
+                       #cooling-cells = <2>;
                };
 
                l2: l2-cache0 {
@@ -466,6 +470,26 @@
        compatible = "amlogic,sm1-clkc";
 };
 
+&cpu_thermal {
+       cooling-maps {
+               map0 {
+                       trip = <&cpu_passive>;
+                       cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+                                       <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+                                       <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+                                       <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+               };
+
+               map1 {
+                       trip = <&cpu_hot>;
+                       cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+                                       <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+                                       <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+                                       <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+               };
+       };
+};
+
 &ethmac {
        power-domains = <&pwrc PWRC_SM1_ETH_ID>;
 };
--

2.22.0

#3 lore raw

PATCH 2/3 boards: amlogic: add Odroid C4 support

In reply to Neil Armstrong

From: Christian Hewitt <[email protected]>

Odroid C4 is an Amlogic SM1 device, the board config and board documentation are adapted from the Odroid-N2 support from the same vendor.

---
 arch/arm/dts/meson-sm1-odroid-c4-u-boot.dtsi |   7 +
 board/amlogic/odroid-n2/MAINTAINERS          |   2 +
 configs/odroid-c4_defconfig                  |  62 +++++++++
 doc/board/amlogic/index.rst                  |   3 +-
 doc/board/amlogic/odroid-c4.rst              | 133 +++++++++++++++++++
 5 files changed, 206 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/dts/meson-sm1-odroid-c4-u-boot.dtsi
 create mode 100644 configs/odroid-c4_defconfig
 create mode 100644 doc/board/amlogic/odroid-c4.rst
arch/arm/dts/meson-sm1-odroid-c4-u-boot.dtsi new file +7 -0
new file mode 100644
index 0000000000..ee32c6f43d
@@ -0,0 +1,7 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 BayLibre, SAS
+ * Author: Neil Armstrong <[email protected]>
+ */
+
+#include "meson-g12-common-u-boot.dtsi"
board/amlogic/odroid-n2/MAINTAINERS +2 -0
index 5627e54058..77f7746346 100644
@@ -4,4 +4,6 @@ S:	Maintained
 L:	u-boot-amlogic at groups.io
 F:	board/amlogic/odroid-n2/
 F:	configs/odroid-n2_defconfig
+F:	configs/odroid-c4_defconfig
 F:	doc/board/amlogic/odroid-n2.rst
+F:	doc/board/amlogic/odroid-c4.rst
configs/odroid-c4_defconfig new file +62 -0

62 lines not on this page · raw message

doc/board/amlogic/index.rst +2 -1
index 3730419167..0e2f8c9aad 100644
@@ -17,7 +17,7 @@ This matrix concerns the actual source code version.
 +===============================+===========+==============+==============+============+============+=============+==============+
 | Boards               		| Odroid-C2 | P212         | Khadas VIM2  | S400       | U200       | Odroid-N2   | SEI610       |
 |				| Nanopi-K2 | Khadas-VIM   | Libretech-PC |	       | SEI510	    | Khadas-VIM3 | Khadas-VIM3L |
-|				| P200	    | LibreTech-CC |	          |	       |            |	          |    	         |
+|				| P200	    | LibreTech-CC |	          |	       |            |	          | Odroid-C4    |
 |				| P201	    | LibreTech-AC |	          |	       |            |             |    	         |
 +-------------------------------+-----------+--------------+--------------+------------+------------+-------------+--------------+
 | UART               		| **Yes**   | **Yes**      | **Yes**      | **Yes**    | **Yes**    | **Yes**     | **Yes**      |
@@ -83,6 +83,7 @@ Board Documentation
    libretech-cc
    nanopi-k2
    odroid-c2
+   odroid-c4
    odroid-n2
    p200
    p201
doc/board/amlogic/odroid-c4.rst new file +133 -0

133 lines not on this page · raw message

Signature · 1 line
2.22.0
#4 lore raw

PATCH 2/3 boards: amlogic: add Odroid C4 support

Hi Neil,

Quoted 9 lines · Neil Armstrong

From: Christian Hewitt <[email protected]>

Odroid C4 is an Amlogic SM1 device, the board config and board documentation are adapted from the Odroid-N2 support from the same vendor.

---

Please add my

Quoted 265 lines
 arch/arm/dts/meson-sm1-odroid-c4-u-boot.dtsi |   7 +
 board/amlogic/odroid-n2/MAINTAINERS          |   2 +
 configs/odroid-c4_defconfig                  |  62 +++++++++
 doc/board/amlogic/index.rst                  |   3 +-
 doc/board/amlogic/odroid-c4.rst              | 133 +++++++++++++++++++
 5 files changed, 206 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/dts/meson-sm1-odroid-c4-u-boot.dtsi
 create mode 100644 configs/odroid-c4_defconfig
 create mode 100644 doc/board/amlogic/odroid-c4.rst
arch/arm/dts/meson-sm1-odroid-c4-u-boot.dtsi new file +7 -0
new file mode 100644
index 0000000000..ee32c6f43d
@@ -0,0 +1,7 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 BayLibre, SAS
+ * Author: Neil Armstrong <[email protected]>
+ */
+
+#include "meson-g12-common-u-boot.dtsi"
board/amlogic/odroid-n2/MAINTAINERS +2 -0
index 5627e54058..77f7746346 100644
@@ -4,4 +4,6 @@ S:      Maintained
 L:     u-boot-amlogic at groups.io
 F:     board/amlogic/odroid-n2/
 F:     configs/odroid-n2_defconfig
+F:     configs/odroid-c4_defconfig
 F:     doc/board/amlogic/odroid-n2.rst
+F:     doc/board/amlogic/odroid-c4.rst
configs/odroid-c4_defconfig new file +62 -0
new file mode 100644
index 0000000000..db9271916e
@@ -0,0 +1,62 @@
+CONFIG_ARM=y
+CONFIG_SYS_BOARD="odroid-n2"
+CONFIG_ARCH_MESON=y
+CONFIG_SYS_TEXT_BASE=0x01000000
+CONFIG_ENV_SIZE=0x2000
+CONFIG_DM_GPIO=y
+CONFIG_MESON_G12A=y
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_DEBUG_UART_BASE=0xff803000
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_IDENT_STRING=" odroid-c4"
+CONFIG_DEBUG_UART=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_MISC_INIT_R=y
+# CONFIG_DISPLAY_CPUINFO is not set
+# CONFIG_CMD_BDI is not set
+# CONFIG_CMD_IMI is not set
+CONFIG_CMD_GPIO=y
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_REGULATOR=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="meson-sm1-odroid-c4"
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_MESON_GX=y
+CONFIG_PHY_REALTEK=y
+CONFIG_DM_ETH=y
+CONFIG_ETH_DESIGNWARE=y
+CONFIG_MESON_G12A_USB_PHY=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_MESON_G12A=y
+CONFIG_POWER_DOMAIN=y
+CONFIG_MESON_EE_POWER_DOMAIN=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_RESET=y
+CONFIG_DEBUG_UART_MESON=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_DEBUG_UART_SKIP_INIT=y
+CONFIG_MESON_SERIAL=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_DWC3=y
+CONFIG_USB_DWC3=y
+# CONFIG_USB_DWC3_GADGET is not set
+CONFIG_USB_DWC3_MESON_G12A=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_VENDOR_NUM=0x1b8e
+CONFIG_USB_GADGET_PRODUCT_NUM=0xfada
+CONFIG_USB_GADGET_DWC2_OTG=y
+CONFIG_USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_DM_VIDEO=y
+CONFIG_VIDEO_MESON=y
+CONFIG_VIDEO_DT_SIMPLEFB=y
+CONFIG_OF_LIBFDT_OVERLAY=y
doc/board/amlogic/index.rst +2 -1
index 3730419167..0e2f8c9aad 100644
@@ -17,7 +17,7 @@ This matrix concerns the actual source code version.
 +===============================+===========+==============+==============+============+============+=============+==============+
 | Boards                               | Odroid-C2 | P212         | Khadas VIM2  | S400       | U200       | Odroid-N2   | SEI610       |
 |                              | Nanopi-K2 | Khadas-VIM   | Libretech-PC |            | SEI510     | Khadas-VIM3 | Khadas-VIM3L |
-|                              | P200      | LibreTech-CC |              |            |            |             |              |
+|                              | P200      | LibreTech-CC |              |            |            |             | Odroid-C4    |
 |                              | P201      | LibreTech-AC |              |            |            |             |              |
 +-------------------------------+-----------+--------------+--------------+------------+------------+-------------+--------------+
 | UART                         | **Yes**   | **Yes**      | **Yes**      | **Yes**    | **Yes**    | **Yes**     | **Yes**      |
@@ -83,6 +83,7 @@ Board Documentation
    libretech-cc
    nanopi-k2
    odroid-c2
+   odroid-c4
    odroid-n2
    p200
    p201
doc/board/amlogic/odroid-c4.rst new file +133 -1
new file mode 100644
index 0000000000..4327d1913f
@@ -0,0 +1,133 @@
+.. SPDX-License-Identifier: GPL-2.0+
+
+U-Boot for ODROID-C4
+====================
+
+ODROID-N2 is a single board computer manufactured by Hardkernel
+Co. Ltd with the following specifications:
+
+ - Amlogic S905X3 Arm Cortex-A55 quad-core SoC
+ - 2GB or 4GB LPDDR4 SDRAM
+ - Gigabit Ethernet
+ - HDMI 2.1 display
+ - 40-pin GPIO header
+ - 7-pin GPIO expansion header
+ - 4x USB 3.0 Host
+ - 1x USB 2.0 Host/OTG (micro)
+ - eMMC, microSD
+ - UART serial
+ - Infrared receiver
+
+Schematics are available on the manufacturer website.
+
+U-Boot compilation
+------------------
+
+    $ export CROSS_COMPILE=aarch64-none-elf-
+    $ make odroid-c4_defconfig
+    $ make
+
+Image creation
+--------------
+
+Amlogic doesn't provide sources for the firmware and for tools needed
+to create the bootloader image, so it is necessary to obtain them from
+the git tree published by the board vendor:
+
+.. code-block:: bash
+
+    $ wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
+    $ wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
+    $ tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
+    $ tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
+    $ export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH
+
+    $ DIR=odroid-c4
+    $ git clone --depth 1 \
+       https://github.com/hardkernel/u-boot.git -b odroidg12-v2015.01 \
+       $DIR
+
+    $ cd odroid-c4
+    $ make odroidc4_defconfig
+    $ make
+    $ export UBOOTDIR=$PWD
+
+ Go back to mainline U-Boot source tree then :
+
+.. code-block:: bash
+
+    $ mkdir fip
+
+    $ wget https://github.com/BayLibre/u-boot/releases/download/v2017.11-libretech-cc/blx_fix_g12a.sh -O fip/blx_fix.sh
+    $ cp $UBOOTDIR/build/scp_task/bl301.bin fip/
+    $ cp $UBOOTDIR/build/board/hardkernel/odroidc4/firmware/acs.bin fip/
+    $ cp $UBOOTDIR/fip/g12a/bl2.bin fip/
+    $ cp $UBOOTDIR/fip/g12a/bl30.bin fip/
+    $ cp $UBOOTDIR/fip/g12a/bl31.img fip/
+    $ cp $UBOOTDIR/fip/g12a/ddr3_1d.fw fip/
+    $ cp $UBOOTDIR/fip/g12a/ddr4_1d.fw fip/
+    $ cp $UBOOTDIR/fip/g12a/ddr4_2d.fw fip/
+    $ cp $UBOOTDIR/fip/g12a/diag_lpddr4.fw fip/
+    $ cp $UBOOTDIR/fip/g12a/lpddr3_1d.fw fip/
+    $ cp $UBOOTDIR/fip/g12a/lpddr4_1d.fw fip/
+    $ cp $UBOOTDIR/fip/g12a/lpddr4_2d.fw fip/
+    $ cp $UBOOTDIR/fip/g12a/piei.fw fip/
+    $ cp $UBOOTDIR/fip/g12a/aml_ddr.fw fip/
+    $ cp u-boot.bin fip/bl33.bin
+
+    $ sh fip/blx_fix.sh \
+       fip/bl30.bin \
+       fip/zero_tmp \
+       fip/bl30_zero.bin \
+       fip/bl301.bin \
+       fip/bl301_zero.bin \
+       fip/bl30_new.bin \
+       bl30
+
+    $ sh fip/blx_fix.sh \
+       fip/bl2.bin \
+       fip/zero_tmp \
+       fip/bl2_zero.bin \
+       fip/acs.bin \
+       fip/bl21_zero.bin \
+       fip/bl2_new.bin \
+       bl2
+
+    $ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl30sig --input fip/bl30_new.bin \
+                                       --output fip/bl30_new.bin.g12a.enc \
+                                       --level v3
+    $ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl3sig --input fip/bl30_new.bin.g12a.enc \
+                                       --output fip/bl30_new.bin.enc \
+                                       --level v3 --type bl30
+    $ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl3sig --input fip/bl31.img \
+                                       --output fip/bl31.img.enc \
+                                       --level v3 --type bl31
+    $ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl3sig --input fip/bl33.bin --compress lz4 \
+                                       --output fip/bl33.bin.enc \
+                                       --level v3 --type bl33 --compress lz4
+    $ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl2sig --input fip/bl2_new.bin \
+                                       --output fip/bl2.n.bin.sig
+    $ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bootmk \
+               --output fip/u-boot.bin \
+               --bl2 fip/bl2.n.bin.sig \
+               --bl30 fip/bl30_new.bin.enc \
+               --bl31 fip/bl31.img.enc \
+               --bl33 fip/bl33.bin.enc \
+               --ddrfw1 fip/ddr4_1d.fw \
+               --ddrfw2 fip/ddr4_2d.fw \
+               --ddrfw3 fip/ddr3_1d.fw \
+               --ddrfw4 fip/piei.fw \
+               --ddrfw5 fip/lpddr4_1d.fw \
+               --ddrfw6 fip/lpddr4_2d.fw \
+               --ddrfw7 fip/diag_lpddr4.fw \
+               --ddrfw8 fip/aml_ddr.fw \
+               --ddrfw9 fip/lpddr3_1d.fw \
+               --level v3
+
+and then write the image to SD with:
+
+.. code-block:: bash
+
+    $ DEV=/dev/your_sd_device
+    $ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1
+    $ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444
--

2.22.0

#5 lore raw

PATCH 3/3 ARM: dts: meson-sm1-odroid-c4: add ethernet PHY reset

In reply to Neil Armstrong

The PHY needs a reset in order to be functionnal for U-Boot, add the old PHY reset bindings for dwmac until we support the new bindings in the PHY node.

---
 arch/arm/dts/meson-sm1-odroid-c4-u-boot.dtsi | 6 ++++++
 1 file changed, 6 insertions(+)
arch/arm/dts/meson-sm1-odroid-c4-u-boot.dtsi +6 -0
index ee32c6f43d..2a8f0545b1 100644
@@ -5,3 +5,9 @@
  */
 
 #include "meson-g12-common-u-boot.dtsi"
+
+&ethmac {
+	snps,reset-gpio = <&gpio GPIOZ_15 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+	snps,reset-delays-us = <0 10000 1000000>;
+	snps,reset-active-low;
+};
Signature · 1 line
2.22.0
#6 lore raw

PATCH 3/3 ARM: dts: meson-sm1-odroid-c4: add ethernet PHY reset

Hi Neil,

Quoted 6 lines · Neil Armstrong

The PHY needs a reset in order to be functionnal for U-Boot, add the old PHY reset bindings for dwmac until we support the new bindings in the PHY node.

---

Please add my

Quoted 20 lines
 arch/arm/dts/meson-sm1-odroid-c4-u-boot.dtsi | 6 ++++++
 1 file changed, 6 insertions(+)
arch/arm/dts/meson-sm1-odroid-c4-u-boot.dtsi +6 -1
index ee32c6f43d..2a8f0545b1 100644
@@ -5,3 +5,9 @@
  */
 
 #include "meson-g12-common-u-boot.dtsi"
+
+&ethmac {
+       snps,reset-gpio = <&gpio GPIOZ_15 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+       snps,reset-delays-us = <0 10000 1000000>;
+       snps,reset-active-low;
+};
--

2.22.0

#7 lore raw

cover board: amlogic: add Odroid C4 support

In reply to Neil Armstrong

Le 01/07/2020 ? 16:43, Neil Armstrong a ?crit :

Quoted 33 lines

This patchset adds support for the Hardkernel Odroid-C4 board based on an Amlogic S905X3 SoC (SM1).

These patches were made very early from Christian Hewitt when the device was unveiled by Hardkernel, and superseed the patchset from Beniamino Galvani posted later.

Beniamino, sorry for posting this over your patchset, but they are essentially the same and this one is already used by LibreELEC, Armbian and out KernelCI boards.

It used the new Odroid-N2 board support instead of W400, and adds a doc file in RsT format.

Christian Hewitt (2):
ARM: dts: sync amlogic G12A/G12B/SM1 DT from Linux 5.8-rc1
boards: amlogic: add Odroid C4 support

Neil Armstrong (1):
ARM: dts: meson-sm1-odroid-c4: add ethernet PHY reset

 arch/arm/dts/Makefile                        |   1 +
 arch/arm/dts/meson-g12-common.dtsi           |  13 +-
 arch/arm/dts/meson-g12.dtsi                  |  32 +-
 arch/arm/dts/meson-g12b-khadas-vim3.dtsi     |  22 +-
 arch/arm/dts/meson-g12b-s922x.dtsi           |  15 +
 arch/arm/dts/meson-g12b.dtsi                 |  22 +
 arch/arm/dts/meson-khadas-vim3.dtsi          |   4 +-
 arch/arm/dts/meson-sm1-odroid-c4-u-boot.dtsi |  13 +
 arch/arm/dts/meson-sm1-odroid-c4.dts         | 402 +++++++++++++++++++
 arch/arm/dts/meson-sm1-sei610.dts            |   2 +-
 arch/arm/dts/meson-sm1.dtsi                  |  24 ++
 board/amlogic/odroid-n2/MAINTAINERS          |   2 +
Quoted 9 lines
 configs/odroid-c4_defconfig                  |  62 +++
 doc/board/amlogic/index.rst                  |   3 +-
 doc/board/amlogic/odroid-c4.rst              | 133 ++++++
 15 files changed, 713 insertions(+), 37 deletions(-)
 create mode 100644 arch/arm/dts/meson-sm1-odroid-c4-u-boot.dtsi
 create mode 100644 arch/arm/dts/meson-sm1-odroid-c4.dts
 create mode 100644 configs/odroid-c4_defconfig
 create mode 100644 doc/board/amlogic/odroid-c4.rst

Applied to u-boot-amlogic