arm: remove it8152 PCI controller driver
PATCH 1/1 arm: remove it8152 PCI controller driver
From: Mike Rapoport <[email protected]>
The it8152 PCI host controller was only used by cm-x2xx platforms. Since these platforms were removed, there is no point to keep it8152 driver.
--- arch/arm/Kconfig | 6 - arch/arm/common/Makefile | 1 - arch/arm/common/it8152.c | 352 ------------------------- arch/arm/include/asm/hardware/it8152.h | 116 -------- arch/arm/kernel/bios32.c | 17 -- 5 files changed, 492 deletions(-) delete mode 100644 arch/arm/common/it8152.c delete mode 100644 arch/arm/include/asm/hardware/it8152.h
arch/arm/Kconfig +0 -6
@@ -1148,12 +1148,6 @@ config PCI_NANOENGINE help Enable PCI on the BSE nanoEngine board. -config PCI_HOST_ITE8152 - bool - depends on PCI && MACH_ARMCORE - default y - select DMABOUNCE - config ARM_ERRATA_814220 bool "ARM errata: Cache maintenance by set/way operations can execute out of order" depends on CPU_V7
arch/arm/common/Makefile +0 -1
@@ -12,7 +12,6 @@ obj-$(CONFIG_SHARP_LOCOMO) += locomo.o obj-$(CONFIG_SHARP_PARAM) += sharpsl_param.o obj-$(CONFIG_SHARP_SCOOP) += scoop.o obj-$(CONFIG_CPU_V7) += secure_cntvoff.o -obj-$(CONFIG_PCI_HOST_ITE8152) += it8152.o obj-$(CONFIG_MCPM) += mcpm_head.o mcpm_entry.o mcpm_platsmp.o vlock.o CFLAGS_REMOVE_mcpm_entry.o = -pg AFLAGS_mcpm_head.o := -march=armv7-a
arch/arm/common/it8152.c deleted +0 -352
352 lines not on this page · raw message
arch/arm/include/asm/hardware/it8152.h deleted +0 -116
116 lines not on this page · raw message
arch/arm/kernel/bios32.c +0 -17
@@ -252,23 +252,6 @@ static void pci_fixup_cy82c693(struct pci_dev *dev) }DECLARE_PCI_FIXUP_HEADER (PCI_VENDOR_ID_CONTAQ ,PCI_DEVICE_ID_CONTAQ_82C693 , pci_fixup_cy82c693); -static void pci_fixup_it8152 (struct pci_dev *dev) -{ -int i; -/* fixup for ITE 8152 devices */ -/* FIXME: add defines for class 0x68000 and 0x80103 */ -if ((dev->class >>8 ) ==PCI_CLASS_BRIDGE_HOST || - dev->class ==0x68000 || - dev->class ==0x80103 ) { -for (i =0 ; i <PCI_NUM_RESOURCES ; i++) { - dev->resource[i].start =0 ; - dev->resource[i].end =0 ; - dev->resource[i].flags =0 ; - } - } -} -DECLARE_PCI_FIXUP_HEADER (PCI_VENDOR_ID_ITE ,PCI_DEVICE_ID_ITE_8152 , pci_fixup_it8152); -/* * If the bus contains any of these devices, then we must not turn on * parity checking of any kind. Currently this is CyberPro 20x0 only.
Signature · 1 line
2.26.2
Any comments?
Shall I put it into the patch system or will it go via arm-soc tree?
Quoted 557 lines · Mike Rapoport
From: Mike Rapoport <[email protected]>
The it8152 PCI host controller was only used by cm-x2xx platforms. Since these platforms were removed, there is no point to keep it8152 driver.
Signed-off-by Mike Rapoport <[email protected]>--- arch/arm/Kconfig | 6 - arch/arm/common/Makefile | 1 - arch/arm/common/it8152.c | 352 ------------------------- arch/arm/include/asm/hardware/it8152.h | 116 -------- arch/arm/kernel/bios32.c | 17 -- 5 files changed, 492 deletions(-) delete mode 100644 arch/arm/common/it8152.c delete mode 100644 arch/arm/include/asm/hardware/it8152.harch/arm/Kconfig +0
-6@@ -1148,12 +1148,6 @@ config PCI_NANOENGINE help Enable PCI on the BSE nanoEngine board. -config PCI_HOST_ITE8152 - bool - depends on PCI && MACH_ARMCORE - default y - select DMABOUNCE - config ARM_ERRATA_814220 bool "ARM errata: Cache maintenance by set/way operations can execute out of order" depends on CPU_V7arch/arm/common/Makefile +0
-1@@ -12,7 +12,6 @@ obj-$(CONFIG_SHARP_LOCOMO) += locomo.o obj-$(CONFIG_SHARP_PARAM) += sharpsl_param.o obj-$(CONFIG_SHARP_SCOOP) += scoop.o obj-$(CONFIG_CPU_V7) += secure_cntvoff.o -obj-$(CONFIG_PCI_HOST_ITE8152) += it8152.o obj-$(CONFIG_MCPM) += mcpm_head.o mcpm_entry.o mcpm_platsmp.o vlock.o CFLAGS_REMOVE_mcpm_entry.o = -pg AFLAGS_mcpm_head.o := -march=armv7-aarch/arm/common/it8152.c deleted +0
-352@@ -1,352 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-only -/* -* linux/arch/arm/common/it8152.c -* -* Copyright Compulab Ltd, 2002-2007 -* Mike Rapoport <[email protected]> -* -* The DMA bouncing part is taken from arch/arm/mach-ixp4xx/common-pci.c -* (see this file for respective copyrights) -* -* Thanks to Guennadi Liakhovetski <[email protected]> for IRQ enumberation -* and demux code. -*/ - -#include <linux/sched.h> -#include <linux/kernel.h> -#include <linux/pci.h> -#include <linux/ptrace.h> -#include <linux/interrupt.h> -#include <linux/mm.h> -#include <linux/init.h> -#include <linux/ioport.h> -#include <linux/irq.h> -#include <linux/io.h> -#include <linux/export.h> - -#include <asm/mach/pci.h> -#include <asm/hardware/it8152.h> - -#define MAX_SLOTS 21 - -static void it8152_mask_irq (struct irq_data *d) -{ -unsigned int irq = d->irq; - -if (irq >=IT8152_LD_IRQ (0 )) { -__raw_writel ((__raw_readl (IT8152_INTC_LDCNIMR ) | - (1 << (irq -IT8152_LD_IRQ (0 )))), -IT8152_INTC_LDCNIMR ); - }else if (irq >=IT8152_LP_IRQ (0 )) { -__raw_writel ((__raw_readl (IT8152_INTC_LPCNIMR ) | - (1 << (irq -IT8152_LP_IRQ (0 )))), -IT8152_INTC_LPCNIMR ); - }else if (irq >=IT8152_PD_IRQ (0 )) { -__raw_writel ((__raw_readl (IT8152_INTC_PDCNIMR ) | - (1 << (irq -IT8152_PD_IRQ (0 )))), -IT8152_INTC_PDCNIMR ); - } -} - -static void it8152_unmask_irq (struct irq_data *d) -{ -unsigned int irq = d->irq; - -if (irq >=IT8152_LD_IRQ (0 )) { -__raw_writel ((__raw_readl (IT8152_INTC_LDCNIMR ) & - ~(1 << (irq -IT8152_LD_IRQ (0 )))), -IT8152_INTC_LDCNIMR ); - }else if (irq >=IT8152_LP_IRQ (0 )) { -__raw_writel ((__raw_readl (IT8152_INTC_LPCNIMR ) & - ~(1 << (irq -IT8152_LP_IRQ (0 )))), -IT8152_INTC_LPCNIMR ); - }else if (irq >=IT8152_PD_IRQ (0 )) { -__raw_writel ((__raw_readl (IT8152_INTC_PDCNIMR ) & - ~(1 << (irq -IT8152_PD_IRQ (0 )))), -IT8152_INTC_PDCNIMR ); - } -} - -static struct irq_chip it8152_irq_chip = { - .name ="it8152" , - .irq_ack = it8152_mask_irq, - .irq_mask = it8152_mask_irq, - .irq_unmask = it8152_unmask_irq, -}; - -void it8152_init_irq (void ) -{ -int irq; - -__raw_writel ((0xffff ),IT8152_INTC_PDCNIMR ); -__raw_writel ((0 ),IT8152_INTC_PDCNIRR ); -__raw_writel ((0xffff ),IT8152_INTC_LPCNIMR ); -__raw_writel ((0 ),IT8152_INTC_LPCNIRR ); -__raw_writel ((0xffff ),IT8152_INTC_LDCNIMR ); -__raw_writel ((0 ),IT8152_INTC_LDCNIRR ); - -for (irq =IT8152_IRQ (0 ); irq <=IT8152_LAST_IRQ ; irq++) { -irq_set_chip_and_handler (irq, &it8152_irq_chip, - handle_level_irq); -irq_clear_status_flags (irq,IRQ_NOREQUEST |IRQ_NOPROBE ); - } -} - -void it8152_irq_demux (struct irq_desc *desc) -{ -int bits_pd, bits_lp, bits_ld; -int i; - -while (1 ) { -/* Read all */ - bits_pd =__raw_readl (IT8152_INTC_PDCNIRR ); - bits_lp =__raw_readl (IT8152_INTC_LPCNIRR ); - bits_ld =__raw_readl (IT8152_INTC_LDCNIRR ); - -/* Ack */ -__raw_writel ((~bits_pd),IT8152_INTC_PDCNIRR ); -__raw_writel ((~bits_lp),IT8152_INTC_LPCNIRR ); -__raw_writel ((~bits_ld),IT8152_INTC_LDCNIRR ); - -if (!(bits_ld | bits_lp | bits_pd)) { -/* Re-read to guarantee, that there was a moment of -time, when they all three were 0. */ - bits_pd =__raw_readl (IT8152_INTC_PDCNIRR ); - bits_lp =__raw_readl (IT8152_INTC_LPCNIRR ); - bits_ld =__raw_readl (IT8152_INTC_LDCNIRR ); -if (!(bits_ld | bits_lp | bits_pd)) -return ; - } - - bits_pd &= ((1 <<IT8152_PD_IRQ_COUNT ) -1 ); -while (bits_pd) { - i =__ffs (bits_pd); -generic_handle_irq (IT8152_PD_IRQ (i)); - bits_pd &= ~(1 << i); - } - - bits_lp &= ((1 <<IT8152_LP_IRQ_COUNT ) -1 ); -while (bits_lp) { - i =__ffs (bits_lp); -generic_handle_irq (IT8152_LP_IRQ (i)); - bits_lp &= ~(1 << i); - } - - bits_ld &= ((1 <<IT8152_LD_IRQ_COUNT ) -1 ); -while (bits_ld) { - i =__ffs (bits_ld); -generic_handle_irq (IT8152_LD_IRQ (i)); - bits_ld &= ~(1 << i); - } - } -} - -/* mapping for on-chip devices */ -int __init it8152_pci_map_irq (const struct pci_dev *dev,u8 slot,u8 pin) -{ -if ((dev->vendor ==PCI_VENDOR_ID_ITE ) && - (dev->device ==PCI_DEVICE_ID_ITE_8152 )) { -if ((dev->class >>8 ) ==PCI_CLASS_MULTIMEDIA_AUDIO ) -return IT8152_AUDIO_INT ; -if ((dev->class >>8 ) ==PCI_CLASS_SERIAL_USB ) -return IT8152_USB_INT ; -if ((dev->class >>8 ) ==PCI_CLASS_SYSTEM_DMA ) -return IT8152_CDMA_INT ; - } - -return 0 ; -} - -static unsigned long it8152_pci_dev_base_address (struct pci_bus *bus, -unsigned int devfn) -{ -unsigned long addr =0 ; - -if (bus->number ==0 ) { -if (devfn <PCI_DEVFN (MAX_SLOTS ,0 )) - addr = (devfn <<8 ); - }else - addr = (bus->number <<16 ) | (devfn <<8 ); - -return addr; -} - -static int it8152_pci_read_config (struct pci_bus *bus, -unsigned int devfn,int where, -int size,u32 *value) -{ -unsigned long addr =it8152_pci_dev_base_address (bus, devfn); -u32 v; -int shift; - - shift = (where &3 ); - -__raw_writel ((addr + where),IT8152_PCI_CFG_ADDR ); - v = (__raw_readl (IT8152_PCI_CFG_DATA ) >> (8 * (shift))); - - *value = v; - -return PCIBIOS_SUCCESSFUL ; -} - -static int it8152_pci_write_config (struct pci_bus *bus, -unsigned int devfn,int where, -int size,u32 value) -{ -unsigned long addr =it8152_pci_dev_base_address (bus, devfn); -u32 v, vtemp, mask =0 ; -int shift; - -if (size ==1 ) - mask =0xff ; -if (size ==2 ) - mask =0xffff ; - - shift = (where &3 ); - -__raw_writel ((addr + where),IT8152_PCI_CFG_ADDR ); - vtemp =__raw_readl (IT8152_PCI_CFG_DATA ); - -if (mask) - vtemp &= ~(mask << (8 * shift)); -else - vtemp =0 ; - - v = (value << (8 * shift)); -__raw_writel ((addr + where),IT8152_PCI_CFG_ADDR ); -__raw_writel ((v | vtemp),IT8152_PCI_CFG_DATA ); - -return PCIBIOS_SUCCESSFUL ; -} - -struct pci_ops it8152_ops = { - .read = it8152_pci_read_config, - .write = it8152_pci_write_config, -}; - -static struct resource it8152_io = { - .name ="IT8152 PCI I/O region" , - .flags =IORESOURCE_IO , -}; - -static struct resource it8152_mem = { - .name ="IT8152 PCI memory region" , - .start =0x10000000 , - .end =0x13e00000 , - .flags =IORESOURCE_MEM , -}; - -/* -* The following functions are needed for DMA bouncing. -* ITE8152 chip can address up to 64MByte, so all the devices -* connected to ITE8152 (PCI and USB) should have limited DMA window -*/ -static int it8152_needs_bounce (struct device *dev,dma_addr_t dma_addr,size_t size) -{ -dev_dbg (dev,"%s: dma_addr %08x, size %08x\n" , - __func__, dma_addr, size); -return (dma_addr + size -PHYS_OFFSET ) >=SZ_64M ; -} - -/* -* Setup DMA mask to 64MB on devices connected to ITE8152. Ignore all -* other devices. -*/ -static int it8152_pci_platform_notify (struct device *dev) -{ -if (dev_is_pci (dev)) { -if (dev->dma_mask) - *dev->dma_mask = (SZ_64M -1 ) |PHYS_OFFSET ; - dev->coherent_dma_mask = (SZ_64M -1 ) |PHYS_OFFSET ; -dmabounce_register_dev (dev,2048 ,4096 , it8152_needs_bounce); - } -return 0 ; -} - -static int it8152_pci_platform_notify_remove (struct device *dev) -{ -if (dev_is_pci (dev)) -dmabounce_unregister_dev (dev); - -return 0 ; -} - -int dma_set_coherent_mask (struct device *dev,u64 mask) -{ -if (mask >=PHYS_OFFSET +SZ_64M -1 ) -return 0 ; - -return -EIO ; -} - -int __init it8152_pci_setup (int nr,struct pci_sys_data *sys) -{ -/* -* FIXME: use pci_ioremap_io to remap the IO space here and -* move over to the generic io.h implementation. -* This requires solving the same problem for PXA PCMCIA -* support. -*/ - it8152_io.start = (unsigned long )IT8152_IO_BASE +0x12000 ; - it8152_io.end = (unsigned long )IT8152_IO_BASE +0x12000 +0x100000 ; - - sys->mem_offset =0x10000000 ; - sys->io_offset = (unsigned long )IT8152_IO_BASE ; - -if (request_resource (&ioport_resource, &it8152_io)) { -printk (KERN_ERR "PCI: unable to allocate IO region\n" ); - goto err0; - } -if (request_resource (&iomem_resource, &it8152_mem)) { -printk (KERN_ERR "PCI: unable to allocate memory region\n" ); - goto err1; - } - -pci_add_resource_offset (&sys->resources, &it8152_io, sys->io_offset); -pci_add_resource_offset (&sys->resources, &it8152_mem, sys->mem_offset); - -if (platform_notify || platform_notify_remove) { -printk (KERN_ERR "PCI: Can't use platform_notify\n" ); - goto err2; - } - - platform_notify = it8152_pci_platform_notify; - platform_notify_remove = it8152_pci_platform_notify_remove; - -return 1 ; - -err2: -release_resource (&it8152_io); -err1: -release_resource (&it8152_mem); -err0: -return -EBUSY ; -} - -/* ITE bridge requires setting latency timer to avoid early bus access -termination by PCI bus master devices -*/ -void pcibios_set_master (struct pci_dev *dev) -{ -u8 lat; - -/* no need to update on-chip OHCI controller */ -if ((dev->vendor ==PCI_VENDOR_ID_ITE ) && - (dev->device ==PCI_DEVICE_ID_ITE_8152 ) && - ((dev->class >>8 ) ==PCI_CLASS_SERIAL_USB )) -return ; - -pci_read_config_byte (dev,PCI_LATENCY_TIMER , &lat); -if (lat <16 ) - lat = (64 <= pcibios_max_latency) ?64 : pcibios_max_latency; -else if (lat > pcibios_max_latency) - lat = pcibios_max_latency; -else -return ; -printk (KERN_DEBUG "PCI: Setting latency timer of device %s to %d\n" , -pci_name (dev), lat); -pci_write_config_byte (dev,PCI_LATENCY_TIMER , lat); -} - - -EXPORT_SYMBOL (dma_set_coherent_mask);arch/arm/include/asm/hardware/it8152.h deleted +0
-116@@ -1,116 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0 */ -/* -* linux/include/arm/hardware/it8152.h -* -* Copyright Compulab Ltd., 2006,2007 -* Mike Rapoport <[email protected]> -* -* ITE 8152 companion chip register definitions -*/ - -#ifndef __ASM_HARDWARE_IT8152_H -#define __ASM_HARDWARE_IT8152_H - -#include <mach/irqs.h> - -extern void __iomem *it8152_base_address; - -#define IT8152_IO_BASE (it8152_base_address + 0x03e00000) -#define IT8152_CFGREG_BASE (it8152_base_address + 0x03f00000) - -#define __REG_IT8152 (x) (it8152_base_address + (x)) - -#define IT8152_PCI_CFG_ADDR __REG_IT8152(0x3f00800) -#define IT8152_PCI_CFG_DATA __REG_IT8152(0x3f00804) - -#define IT8152_INTC_LDCNIRR __REG_IT8152(0x3f00300) -#define IT8152_INTC_LDPNIRR __REG_IT8152(0x3f00304) -#define IT8152_INTC_LDCNIMR __REG_IT8152(0x3f00308) -#define IT8152_INTC_LDPNIMR __REG_IT8152(0x3f0030C) -#define IT8152_INTC_LDNITR __REG_IT8152(0x3f00310) -#define IT8152_INTC_LDNIAR __REG_IT8152(0x3f00314) -#define IT8152_INTC_LPCNIRR __REG_IT8152(0x3f00320) -#define IT8152_INTC_LPPNIRR __REG_IT8152(0x3f00324) -#define IT8152_INTC_LPCNIMR __REG_IT8152(0x3f00328) -#define IT8152_INTC_LPPNIMR __REG_IT8152(0x3f0032C) -#define IT8152_INTC_LPNITR __REG_IT8152(0x3f00330) -#define IT8152_INTC_LPNIAR __REG_IT8152(0x3f00334) -#define IT8152_INTC_PDCNIRR __REG_IT8152(0x3f00340) -#define IT8152_INTC_PDPNIRR __REG_IT8152(0x3f00344) -#define IT8152_INTC_PDCNIMR __REG_IT8152(0x3f00348) -#define IT8152_INTC_PDPNIMR __REG_IT8152(0x3f0034C) -#define IT8152_INTC_PDNITR __REG_IT8152(0x3f00350) -#define IT8152_INTC_PDNIAR __REG_IT8152(0x3f00354) -#define IT8152_INTC_INTC_TYPER __REG_IT8152(0x3f003FC) - -#define IT8152_GPIO_GPDR __REG_IT8152(0x3f00500) - -/* -Interrupt controller per register summary: ---------------------------------------- -LCDNIRR: -IT8152_LD_IRQ(8) PCICLK stop -IT8152_LD_IRQ(7) MCLK ready -IT8152_LD_IRQ(6) s/w -IT8152_LD_IRQ(5) UART -IT8152_LD_IRQ(4) GPIO -IT8152_LD_IRQ(3) TIMER 4 -IT8152_LD_IRQ(2) TIMER 3 -IT8152_LD_IRQ(1) TIMER 2 -IT8152_LD_IRQ(0) TIMER 1 - -LPCNIRR: -IT8152_LP_IRQ(x) serial IRQ x - -PCIDNIRR: -IT8152_PD_IRQ(14) PCISERR -IT8152_PD_IRQ(13) CPU/PCI bridge target abort (h2pTADR) -IT8152_PD_IRQ(12) CPU/PCI bridge master abort (h2pMADR) -IT8152_PD_IRQ(11) PCI INTD -IT8152_PD_IRQ(10) PCI INTC -IT8152_PD_IRQ(9) PCI INTB -IT8152_PD_IRQ(8) PCI INTA -IT8152_PD_IRQ(7) serial INTD -IT8152_PD_IRQ(6) serial INTC -IT8152_PD_IRQ(5) serial INTB -IT8152_PD_IRQ(4) serial INTA -IT8152_PD_IRQ(3) serial IRQ IOCHK (IOCHKR) -IT8152_PD_IRQ(2) chaining DMA (CDMAR) -IT8152_PD_IRQ(1) USB (USBR) -IT8152_PD_IRQ(0) Audio controller (ACR) -*/ -#define IT8152_IRQ (x) (IRQ_BOARD_START + (x)) -#define IT8152_LAST_IRQ (IRQ_BOARD_START + 40) - -/* IRQ-sources in 3 groups - local devices, LPC (serial), and external PCI */ -#define IT8152_LD_IRQ_COUNT 9 -#define IT8152_LP_IRQ_COUNT 16 -#define IT8152_PD_IRQ_COUNT 15 - -/* Priorities: */ -#define IT8152_PD_IRQ (i) IT8152_IRQ(i) -#define IT8152_LP_IRQ (i) (IT8152_IRQ(i) + IT8152_PD_IRQ_COUNT) -#define IT8152_LD_IRQ (i) (IT8152_IRQ(i) + IT8152_PD_IRQ_COUNT + IT8152_LP_IRQ_COUNT) - -/* frequently used interrupts */ -#define IT8152_PCISERR IT8152_PD_IRQ(14) -#define IT8152_H2PTADR IT8152_PD_IRQ(13) -#define IT8152_H2PMAR IT8152_PD_IRQ(12) -#define IT8152_PCI_INTD IT8152_PD_IRQ(11) -#define IT8152_PCI_INTC IT8152_PD_IRQ(10) -#define IT8152_PCI_INTB IT8152_PD_IRQ(9) -#define IT8152_PCI_INTA IT8152_PD_IRQ(8) -#define IT8152_CDMA_INT IT8152_PD_IRQ(2) -#define IT8152_USB_INT IT8152_PD_IRQ(1) -#define IT8152_AUDIO_INT IT8152_PD_IRQ(0) - -struct pci_dev ; -struct pci_sys_data ; - -extern void it8152_irq_demux (struct irq_desc *desc); -extern void it8152_init_irq (void ); -extern int it8152_pci_map_irq (const struct pci_dev *dev,u8 slot,u8 pin); -extern int it8152_pci_setup (int nr,struct pci_sys_data *sys); -extern struct pci_ops it8152_ops; - -#endif /* __ASM_HARDWARE_IT8152_H */ arch/arm/kernel/bios32.c +0
-17@@ -252,23 +252,6 @@ static void pci_fixup_cy82c693(struct pci_dev *dev) }DECLARE_PCI_FIXUP_HEADER (PCI_VENDOR_ID_CONTAQ ,PCI_DEVICE_ID_CONTAQ_82C693 , pci_fixup_cy82c693); -static void pci_fixup_it8152 (struct pci_dev *dev) -{ -int i; -/* fixup for ITE 8152 devices */ -/* FIXME: add defines for class 0x68000 and 0x80103 */ -if ((dev->class >>8 ) ==PCI_CLASS_BRIDGE_HOST || - dev->class ==0x68000 || - dev->class ==0x80103 ) { -for (i =0 ; i <PCI_NUM_RESOURCES ; i++) { - dev->resource[i].start =0 ; - dev->resource[i].end =0 ; - dev->resource[i].flags =0 ; - } - } -} -DECLARE_PCI_FIXUP_HEADER (PCI_VENDOR_ID_ITE ,PCI_DEVICE_ID_ITE_8152 , pci_fixup_it8152); -/* * If the bus contains any of these devices, then we must not turn on * parity checking of any kind. Currently this is CyberPro 20x0 only. Signature · 1 line
2.26.2
Signature · 2 lines
Sincerely yours, Mike.
Arnd Bergmann
Acked-byQuoted 2 lines · Mike Rapoport
Any comments?
Looks good to me. I actually have a similar patch in my backlog, but I never got around to sending that, so let's take your version.
Quoted 2 lines
Shall I put it into the patch system or will it go via arm-soc tree?
I'd suggest the patch tracker, unless Russell wants me to pick it up the in the soc tree instead.
Arnd