Skip to contentSkip to conversation

PCI: brcmstb: enable PCIe for STB chips

PATCH Superseded Jim Quinlan 7 participants 33 messages Jul 24, 2020 – Aug 3, 2020

Subsystems (30)

v9 of 12 Superseded Latest is v12 →

lore
Share & tools
lore
#0 lore raw

v9 cover PCI: brcmstb: enable PCIe for STB chips

Patchset Summary:
Enhance a PCIe host controller driver. Because of its unusual design we are foced to change dev->dma_pfn_offset into a more general role allowing multiple offsets. See the 'v1' notes below for more info.

NOTE: ChristophH wanted the dma_set_offset_range() function
to have a range from [0...~(phys_addr_t)0], i.e. no specific bounds. RobinM requested this function to have specific bounds, which has been implemented since v6. If I do not hear from Robin in the near future about this request, I will submit v10 which will have no specific bounds.

v9:
Commit: "device core: Introduce DMA range map, supplanting ..." -- A number of code improvements were implemented as suggested by
ChristophH. Unfortunately, some of these changes reversed the implemented suggestions of other reviewers; for example, the new macros PFN_DMA_ADDR(), DMA_ADDR_PFN() have been pulled.

v8:
Commit: "device core: Introduce DMA range map, supplanting ..." -- To satisfy a specific m68 compile configuration, I moved the 'struct
bus_dma_region; definition out of #ifdef CONFIG_HAS_DMA and also defined three inline functions for !CONFIG_HAS_DMA (kernel test robot).
-- The sunXi drivers -- suc4i_csi, sun6i_csi, cedrus_hw -- set
a pfn_offset outside of_dma_configure() but the code offers no insight on the size of the translation window. V7 had me using SIZE_MAX as the size. I have since contacted the sunXi maintainer and he said that using a size of SZ_4G would cover sunXi configurations.

v7:
Commit: "device core: Introduce DMA range map, supplanting ..." -- remove second kcalloc/copy in device.c (AndyS)
-- use PTR_ERR_OR_ZERO() and PHYS_PFN() (AndyS)
-- indentation, sizeof(struct ...) => sizeof(*r) (AndyS) -- add pfn.h definitions: PFN_DMA_ADDR(), DMA_ADDR_PFN() (AndyS) -- Fixed compile error in "sun6i_csi.c" (kernel test robot) Commit "ata: ahci_brcm: Fix use of BCM7216 reset controller" -- correct name of function in the commit msg (SergeiS)

v6:
Commit "device core: Introduce DMA range map":
-- of_dma_get_range() now takes a single argument and returns either
NULL, a valid map, or an ERR_PTR. (Robin)
-- offsets are no longer a PFN value but an actual address. (Robin) -- the bus_dma_region struct stores the range size instead of
the cpu_end and pci_end values. (Robin)
-- devices that were setting a single offset with no boundaries
have been modified to have boundaries; in a few places where this information was unavilable a /* FIXME: ... */ comment was added. (Robin)
-- dma_attach_offset_range() can be called when an offset
map already exists; if it's range is already present nothing is done and success is returned. (Robin)
All commits:
-- Man name/style/corrections/etc changed (Bjorn)
-- rebase to Torvalds master

v5:
Commit "device core: Introduce multiple dma pfn offsets" -- in of/address.c: "map_size = 0" => "*map_size = 0" -- use kcalloc instead of kzalloc (AndyS)
-- use PHYS_ADDR_MAX instead of "~(phys_addr_t)0" Commit "PCI: brcmstb: Set internal memory viewport sizes" -- now gives error on missing dma-ranges property. Commit "dt-bindings: PCI: Add bindings for more Brcmstb chips" -- removed "Allof:" from brcm,scb-sizes definition (RobH) All Commits:
-- indentation style, use max chars 100 (AndyS)
-- rebased to torvalds master

v4:
Commit "device core: Introduce multiple dma pfn offsets" -- of_dma_get_range() does not take a dev param but instead
takes two "out" params: map and map_size. We do this so that the code that parses dma-ranges is separate from
the code that modifies 'dev'. (Nicolas)
-- the separate case of having a single pfn offset has
been removed and is now processed by going through the map array. (Nicolas)
-- move attach_uniform_dma_pfn_offset() from of/address.c to
dma/mapping.c so that it does not depend on CONFIG_OF. (Nicolas)
-- devm_kcalloc => devm_kzalloc (DanC)
-- add/fix assignment to dev->dma_pfn_offset_map for func
attach_uniform_dma_pfn_offset() (DanC, Nicolas)
-- s/struct dma_pfn_offset_region/struct bus_dma_region/ (Nicolas) -- s/attach_uniform_dma_pfn_offset/dma_attach_uniform_pfn_offset/ -- s/attach_dma_pfn_offset_map/dma_attach_pfn_offset_map/ -- More use of PFN_{PHYS,DOWN,UP}. (AndyS)
Commit "of: Include a dev param in of_dma_get_range()" -- this commit was sqaushed with "device core: Introduce ..."

v3:
Commit "device core: Introduce multiple dma pfn offsets" Commit "arm: dma-mapping: Invoke dma offset func if needed" -- The above two commits have been squashed. More importantly,
the code has been modified so that the functionality for multiple pfn offsets subsumes the use of dev->dma_pfn_offset. In fact, dma_pfn_offset is removed and supplanted by dma_pfn_offset_map, which is a pointer to an array. The more common case of a uniform offset is now handled as a map with a single entry, while cases requiring multiple pfn offsets use a map with multiple entries. Code paths that used to do this:

dev->dma_pfn_offset = mydrivers_pfn_offset;

have been changed to do this:

attach_uniform_dma_pfn_offset(dev, pfn_offset);

Commit "dt-bindings: PCI: Add bindings for more Brcmstb chips" -- Add if/then clause for required props: resets, reset-names (RobH) -- Change compatible list from const to enum (RobH)
-- Change list of u32-tuples to u64 (RobH)

Commit "of: Include a dev param in of_dma_get_range()"
-- modify of/unittests.c to add NULL param in of_dma_get_range() call.

Commit "device core: Add ability to handle multiple dma offsets" -- align comment in device.h (AndyS).
-- s/cpu_beg/cpu_start/ and s/dma_beg/dma_start/ in struct
dma_pfn_offset_region (AndyS).

v2:
Commit: "device core: Add ability to handle multiple dma offsets"
o Added helper func attach_dma_pfn_offset_map() in address.c (Chistoph)
o Helpers funcs added to __phys_to_dma() & __dma_to_phys() (Christoph)
o Added warning when multiple offsets are needed and !DMA_PFN_OFFSET_MAP
o dev->dma_pfn_map => dev->dma_pfn_offset_map
o s/frm/from/ for dma_pfn_offset_frm_{phys,dma}_addr() (Christoph)
o In device.h: s/const void */const struct dma_pfn_offset_region */
o removed 'unlikely' from unlikely(dev->dma_pfn_offset_map) since guarded by CONFIG_DMA_PFN_OFFSET_MAP (Christoph)
o Since dev->dma_pfn_offset is copied in usb/core/{usb,message}.c, now

    dev->dma_pfn_offset_map is copied as well.

o Merged two of the DMA commits into one (Christoph).

Commit "arm: dma-mapping: Invoke dma offset func if needed":
o Use helper functions instead of #if CONFIG_DMA_PFN_OFFSET

Other commits' changes:
o Removed need for carrying of_id var in priv (Nicolas)
o Commit message rewordings (Bjorn)
o Commit log messages filled to 75 chars (Bjorn)
o devm_reset_control_get_shared())
=> devm_reset_control_get_optional_shared (Philipp)
o Add call to reset_control_assert() in PCIe remove routines (Philipp)

v1:
This patchset expands the usefulness of the Broadcom Settop Box PCIe controller by building upon the PCIe driver used currently by the Raspbery Pi. Other forms of this patchset were submitted by me years ago and not accepted; the major sticking point was the code required for the DMA remapping needed for the PCIe driver to work [1].

There have been many changes to the DMA and OF subsystems since that time, making a cleaner and less intrusive patchset possible. This patchset implements a generalization of "dev->dma_pfn_offset", except that instead of a single scalar offset it provides for multiple offsets via a function which depends upon the "dma-ranges" property of the PCIe host controller. This is required for proper functionality of the BrcmSTB PCIe controller and possibly some other devices.

[1] https://lore.kernel.org/linux-arm-kernel/[email protected]/

Jim Quinlan (12):
PCI: brcmstb: PCIE_BRCMSTB depends on ARCH_BRCMSTB
ata: ahci_brcm: Fix use of BCM7216 reset controller
dt-bindings: PCI: Add bindings for more Brcmstb chips
PCI: brcmstb: Add bcm7278 register info
PCI: brcmstb: Add suspend and resume pm_ops
PCI: brcmstb: Add bcm7278 PERST# support
PCI: brcmstb: Add control of rescal reset
device core: Introduce DMA range map, supplanting dma_pfn_offset
PCI: brcmstb: Set additional internal memory DMA viewport sizes
PCI: brcmstb: Accommodate MSI for older chips
PCI: brcmstb: Set bus max burst size by chip type
PCI: brcmstb: Add bcm7211, bcm7216, bcm7445, bcm7278 to match list

 .../bindings/pci/brcm,stb-pcie.yaml           |  56 ++-
 arch/arm/include/asm/dma-mapping.h            |  10 +-
 arch/arm/mach-keystone/keystone.c             |  17 +-
 arch/sh/drivers/pci/pcie-sh7786.c             |   9 +-
 arch/sh/kernel/dma-coherent.c                 |  15 +-
 arch/x86/pci/sta2x11-fixup.c                  |   7 +-
 drivers/acpi/arm64/iort.c                     |   5 +-
 drivers/ata/ahci_brcm.c                       |  11 +-
 drivers/gpu/drm/sun4i/sun4i_backend.c         |   5 +-
 drivers/iommu/io-pgtable-arm.c                |   2 +-
 .../platform/sunxi/sun4i-csi/sun4i_csi.c      |   5 +-
 .../platform/sunxi/sun6i-csi/sun6i_csi.c      |   4 +-
 drivers/of/address.c                          |  71 ++-
 drivers/of/device.c                           |  43 +-
 drivers/of/of_private.h                       |  10 +-
 drivers/of/unittest.c                         |  32 +-
 drivers/pci/controller/Kconfig                |   3 +-
 drivers/pci/controller/pcie-brcmstb.c         | 409 +++++++++++++++---
 drivers/remoteproc/remoteproc_core.c          |   2 +-
 .../staging/media/sunxi/cedrus/cedrus_hw.c    |   7 +-
 drivers/usb/core/message.c                    |   4 +-
 drivers/usb/core/usb.c                        |   2 +-
 include/linux/device.h                        |   4 +-
 include/linux/dma-direct.h                    |   8 +-
 include/linux/dma-mapping.h                   |  34 ++
 kernel/dma/coherent.c                         |  10 +-
 kernel/dma/mapping.c                          |  63 +++
 27 files changed, 653 insertions(+), 195 deletions(-)
Signature · 1 line
2.17.1
#32 lore raw

PATCH v9 12/12 PCI: brcmstb: Add bcm7211, bcm7216, bcm7445, bcm7278 to match list

Now that the support is in place with previous commits, we add several chips that use the BrcmSTB driver.

---
 drivers/pci/controller/pcie-brcmstb.c | 4 ++++
 1 file changed, 4 insertions(+)
drivers/pci/controller/pcie-brcmstb.c +4 -0
index 87a6f51d821a..49cbbc1405a1 100644
@@ -1187,6 +1187,10 @@ static int brcm_pcie_remove(struct platform_device *pdev)
 
 static const struct of_device_id brcm_pcie_match[] = {
 	{ .compatible = "brcm,bcm2711-pcie", .data = &bcm2711_cfg },
+	{ .compatible = "brcm,bcm7211-pcie", .data = &generic_cfg },
+	{ .compatible = "brcm,bcm7278-pcie", .data = &bcm7278_cfg },
+	{ .compatible = "brcm,bcm7216-pcie", .data = &bcm7278_cfg },
+	{ .compatible = "brcm,bcm7445-pcie", .data = &generic_cfg },
 	{},
 };
 
Signature · 1 line
2.17.1
#7 lore raw

PATCH v9 4/12 PCI: brcmstb: Add bcm7278 register info

In reply to Jim Quinlan

From: Jim Quinlan <[email protected]>

Add in compatibility strings and code for three Broadcom STB chips. Some of the register locations, shifts, and masks are different for certain chips, requiring the use of different constants based on of_id.

We would like to add the following at this time to the match list but we need to wait until the end of this patchset so that everything works.

    { .compatible = "brcm,bcm7211-pcie", .data = &generic_cfg },
    { .compatible = "brcm,bcm7278-pcie", .data = &bcm7278_cfg },
    { .compatible = "brcm,bcm7216-pcie", .data = &bcm7278_cfg },
    { .compatible = "brcm,bcm7445-pcie", .data = &generic_cfg },
---
 drivers/pci/controller/pcie-brcmstb.c | 105 +++++++++++++++++++++++---
 1 file changed, 93 insertions(+), 12 deletions(-)
drivers/pci/controller/pcie-brcmstb.c +93 -12
index 7730ea845ff2..b7a222fde3c4 100644
@@ -122,9 +122,8 @@
 #define  PCIE_EXT_SLOT_SHIFT				15
 #define  PCIE_EXT_FUNC_SHIFT				12
 
-#define PCIE_RGR1_SW_INIT_1				0x9210
 #define  PCIE_RGR1_SW_INIT_1_PERST_MASK			0x1
-#define  PCIE_RGR1_SW_INIT_1_INIT_MASK			0x2
+#define  PCIE_RGR1_SW_INIT_1_PERST_SHIFT		0x0
 
 /* PCIe parameters */
 #define BRCM_NUM_PCIE_OUT_WINS		0x4
@@ -154,6 +153,73 @@
 #define SSC_STATUS_SSC_MASK		0x400
 #define SSC_STATUS_PLL_LOCK_MASK	0x800
 
+#define IDX_ADDR(pcie)			(pcie->reg_offsets[EXT_CFG_INDEX])
+#define DATA_ADDR(pcie)			(pcie->reg_offsets[EXT_CFG_DATA])
+#define PCIE_RGR1_SW_INIT_1(pcie)	(pcie->reg_offsets[RGR1_SW_INIT_1])
+
+enum {
+	RGR1_SW_INIT_1,
+	EXT_CFG_INDEX,
+	EXT_CFG_DATA,
+};
+
+enum {
+	RGR1_SW_INIT_1_INIT_MASK,
+	RGR1_SW_INIT_1_INIT_SHIFT,
+};
+
+enum pcie_type {
+	GENERIC,
+	BCM7278,
+	BCM2711,
+};
+
+struct pcie_cfg_data {
+	const int *reg_field_info;
+	const int *offsets;
+	const enum pcie_type type;
+};
+
+static const int pcie_reg_field_info[] = {
+	[RGR1_SW_INIT_1_INIT_MASK] = 0x2,
+	[RGR1_SW_INIT_1_INIT_SHIFT] = 0x1,
+};
+
+static const int pcie_reg_field_info_bcm7278[] = {
+	[RGR1_SW_INIT_1_INIT_MASK] = 0x1,
+	[RGR1_SW_INIT_1_INIT_SHIFT] = 0x0,
+};
+
+static const int pcie_offsets[] = {
+	[RGR1_SW_INIT_1] = 0x9210,
+	[EXT_CFG_INDEX]  = 0x9000,
+	[EXT_CFG_DATA]   = 0x9004,
+};
+
+static const struct pcie_cfg_data generic_cfg = {
+	.reg_field_info	= pcie_reg_field_info,
+	.offsets	= pcie_offsets,
+	.type		= GENERIC,
+};
+
+static const int pcie_offset_bcm7278[] = {
+	[RGR1_SW_INIT_1] = 0xc010,
+	[EXT_CFG_INDEX] = 0x9000,
+	[EXT_CFG_DATA] = 0x9004,
+};
+
+static const struct pcie_cfg_data bcm7278_cfg = {
+	.reg_field_info = pcie_reg_field_info_bcm7278,
+	.offsets	= pcie_offset_bcm7278,
+	.type		= BCM7278,
+};
+
+static const struct pcie_cfg_data bcm2711_cfg = {
+	.reg_field_info	= pcie_reg_field_info,
+	.offsets	= pcie_offsets,
+	.type		= BCM2711,
+};
+
 struct brcm_msi {
 	struct device		*dev;
 	void __iomem		*base;
@@ -178,6 +244,9 @@ struct brcm_pcie {
 	int			gen;
 	u64			msi_target_addr;
 	struct brcm_msi		*msi;
+	const int		*reg_offsets;
+	const int		*reg_field_info;
+	enum pcie_type		type;
 };
 
 /*
@@ -604,20 +673,21 @@ static struct pci_ops brcm_pcie_ops = {
 
 static inline void brcm_pcie_bridge_sw_init_set(struct brcm_pcie *pcie, u32 val)
 {
-	u32 tmp;
+	u32 tmp, mask =  pcie->reg_field_info[RGR1_SW_INIT_1_INIT_MASK];
+	u32 shift = pcie->reg_field_info[RGR1_SW_INIT_1_INIT_SHIFT];
 
-	tmp = readl(pcie->base + PCIE_RGR1_SW_INIT_1);
-	u32p_replace_bits(&tmp, val, PCIE_RGR1_SW_INIT_1_INIT_MASK);
-	writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1);
+	tmp = readl(pcie->base + PCIE_RGR1_SW_INIT_1(pcie));
+	tmp = (tmp & ~mask) | ((val << shift) & mask);
+	writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1(pcie));
 }
 
 static inline void brcm_pcie_perst_set(struct brcm_pcie *pcie, u32 val)
 {
 	u32 tmp;
 
-	tmp = readl(pcie->base + PCIE_RGR1_SW_INIT_1);
+	tmp = readl(pcie->base + PCIE_RGR1_SW_INIT_1(pcie));
 	u32p_replace_bits(&tmp, val, PCIE_RGR1_SW_INIT_1_PERST_MASK);
-	writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1);
+	writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1(pcie));
 }
 
 static inline int brcm_pcie_get_rc_bar2_size_and_offset(struct brcm_pcie *pcie,
@@ -927,11 +997,17 @@ static int brcm_pcie_remove(struct platform_device *pdev)
 	return 0;
 }
 
+static const struct of_device_id brcm_pcie_match[] = {
+	{ .compatible = "brcm,bcm2711-pcie", .data = &bcm2711_cfg },
+	{},
+};
+
 static int brcm_pcie_probe(struct platform_device *pdev)
 {
 	struct device_node *np = pdev->dev.of_node, *msi_np;
 	struct pci_host_bridge *bridge;
 	struct device_node *fw_np;
+	const struct pcie_cfg_data *data;
 	struct brcm_pcie *pcie;
 	struct pci_bus *child;
 	struct resource *res;
@@ -955,9 +1031,18 @@ static int brcm_pcie_probe(struct platform_device *pdev)
 	if (!bridge)
 		return -ENOMEM;
 
+	data = of_device_get_match_data(&pdev->dev);
+	if (!data) {
+		pr_err("failed to look up compatible string\n");
+		return -EINVAL;
+	}
+
 	pcie = pci_host_bridge_priv(bridge);
 	pcie->dev = &pdev->dev;
 	pcie->np = np;
+	pcie->reg_offsets = data->offsets;
+	pcie->reg_field_info = data->reg_field_info;
+	pcie->type = data->type;
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	pcie->base = devm_ioremap_resource(&pdev->dev, res);
@@ -1023,10 +1108,6 @@ static int brcm_pcie_probe(struct platform_device *pdev)
 	return ret;
 }
 
-static const struct of_device_id brcm_pcie_match[] = {
-	{ .compatible = "brcm,bcm2711-pcie" },
-	{},
-};
 MODULE_DEVICE_TABLE(of, brcm_pcie_match);
 
 static struct platform_driver brcm_pcie_driver = {
Signature · 1 line
2.17.1
#8 lore raw

PATCH v9 5/12 PCI: brcmstb: Add suspend and resume pm_ops

In reply to Jim Quinlan

From: Jim Quinlan <[email protected]>

Broadcom Set-top (BrcmSTB) boards typically support S2, S3, and S5 suspend and resume. Now the PCIe driver may do so as well.

---
 drivers/pci/controller/pcie-brcmstb.c | 47 +++++++++++++++++++++++++++
 1 file changed, 47 insertions(+)
drivers/pci/controller/pcie-brcmstb.c +47 -0
index b7a222fde3c4..7c148eb65170 100644
@@ -979,6 +979,47 @@ static void brcm_pcie_turn_off(struct brcm_pcie *pcie)
 	brcm_pcie_bridge_sw_init_set(pcie, 1);
 }
 
+static int brcm_pcie_suspend(struct device *dev)
+{
+	struct brcm_pcie *pcie = dev_get_drvdata(dev);
+
+	brcm_pcie_turn_off(pcie);
+	clk_disable_unprepare(pcie->clk);
+
+	return 0;
+}
+
+static int brcm_pcie_resume(struct device *dev)
+{
+	struct brcm_pcie *pcie = dev_get_drvdata(dev);
+	void __iomem *base;
+	u32 tmp;
+	int ret;
+
+	base = pcie->base;
+	clk_prepare_enable(pcie->clk);
+
+	/* Take bridge out of reset so we can access the SERDES reg */
+	brcm_pcie_bridge_sw_init_set(pcie, 0);
+
+	/* SERDES_IDDQ = 0 */
+	tmp = readl(base + PCIE_MISC_HARD_PCIE_HARD_DEBUG);
+	u32p_replace_bits(&tmp, 0, PCIE_MISC_HARD_PCIE_HARD_DEBUG_SERDES_IDDQ_MASK);
+	writel(tmp, base + PCIE_MISC_HARD_PCIE_HARD_DEBUG);
+
+	/* wait for serdes to be stable */
+	udelay(100);
+
+	ret = brcm_pcie_setup(pcie);
+	if (ret)
+		return ret;
+
+	if (pcie->msi)
+		brcm_msi_set_regs(pcie->msi);
+
+	return 0;
+}
+
 static void __brcm_pcie_remove(struct brcm_pcie *pcie)
 {
 	brcm_msi_remove(pcie);
@@ -1110,12 +1151,18 @@ static int brcm_pcie_probe(struct platform_device *pdev)
 
 MODULE_DEVICE_TABLE(of, brcm_pcie_match);
 
+static const struct dev_pm_ops brcm_pcie_pm_ops = {
+	.suspend_noirq = brcm_pcie_suspend,
+	.resume_noirq = brcm_pcie_resume,
+};
+
 static struct platform_driver brcm_pcie_driver = {
 	.probe = brcm_pcie_probe,
 	.remove = brcm_pcie_remove,
 	.driver = {
 		.name = "brcm-pcie",
 		.of_match_table = brcm_pcie_match,
+		.pm = &brcm_pcie_pm_ops,
 	},
 };
 module_platform_driver(brcm_pcie_driver);
Signature · 1 line
2.17.1
#11 lore raw

PATCH v9 8/12 device core: Introduce DMA range map, supplanting dma_pfn_offset

In reply to Jim Quinlan

The new field 'dma_range_map' in struct device is used to facilitate the use of single or multiple offsets between mapping regions of cpu addrs and dma addrs. It subsumes the role of "dev->dma_pfn_offset" which was only capable of holding a single uniform offset and had no region bounds checking.

The function of_dma_get_range() has been modified so that it takes a single argument -- the device node -- and returns a map, NULL, or an error code. The map is an array that holds the information regarding the DMA regions. Each range entry contains the address offset, the cpu_start address, the dma_start address, and the size of the region.

of_dma_configure() is the typical manner to set range offsets but there are a number of ad hoc assignments to "dev->dma_pfn_offset" in the kernel driver code. These cases now invoke the function dma_attach_offset_range(dev, cpu_addr, dma_addr, size).

---
 arch/arm/include/asm/dma-mapping.h            | 10 +--
 arch/arm/mach-keystone/keystone.c             | 17 +++--
 arch/sh/drivers/pci/pcie-sh7786.c             |  9 +--
 arch/sh/kernel/dma-coherent.c                 | 15 ++--
 arch/x86/pci/sta2x11-fixup.c                  |  7 +-
 drivers/acpi/arm64/iort.c                     |  5 +-
 drivers/gpu/drm/sun4i/sun4i_backend.c         |  5 +-
 drivers/iommu/io-pgtable-arm.c                |  2 +-
 .../platform/sunxi/sun4i-csi/sun4i_csi.c      |  5 +-
 .../platform/sunxi/sun6i-csi/sun6i_csi.c      |  4 +-
 drivers/of/address.c                          | 71 ++++++++-----------
 drivers/of/device.c                           | 43 ++++++-----
 drivers/of/of_private.h                       | 10 +--
 drivers/of/unittest.c                         | 32 ++++++---
 drivers/pci/controller/pcie-brcmstb.c         |  1 +
 drivers/remoteproc/remoteproc_core.c          |  2 +-
 .../staging/media/sunxi/cedrus/cedrus_hw.c    |  7 +-
 drivers/usb/core/message.c                    |  4 +-
 drivers/usb/core/usb.c                        |  2 +-
 include/linux/device.h                        |  4 +-
 include/linux/dma-direct.h                    |  8 +--
 include/linux/dma-mapping.h                   | 34 +++++++++
 kernel/dma/coherent.c                         | 10 +--
 kernel/dma/mapping.c                          | 63 ++++++++++++++++
 24 files changed, 248 insertions(+), 122 deletions(-)
arch/arm/include/asm/dma-mapping.h +6 -4
index bdd80ddbca34..2405afeb7957 100644
@@ -35,8 +35,11 @@ static inline const struct dma_map_ops *get_arch_dma_ops(struct bus_type *bus)
 #ifndef __arch_pfn_to_dma
 static inline dma_addr_t pfn_to_dma(struct device *dev, unsigned long pfn)
 {
-	if (dev)
-		pfn -= dev->dma_pfn_offset;
+	if (dev) {
+		phys_addr_t paddr = PFN_PHYS(pfn);
+
+		pfn -= (dma_offset_from_phys_addr(dev, paddr) >> PAGE_SHIFT);
+	}
 	return (dma_addr_t)__pfn_to_bus(pfn);
 }
 
@@ -45,8 +48,7 @@ static inline unsigned long dma_to_pfn(struct device *dev, dma_addr_t addr)
 	unsigned long pfn = __bus_to_pfn(addr);
 
 	if (dev)
-		pfn += dev->dma_pfn_offset;
-
+		pfn += (dma_offset_from_dma_addr(dev, addr) >> PAGE_SHIFT);
 	return pfn;
 }
 
arch/arm/mach-keystone/keystone.c +8 -9
index 638808c4e122..78808942ad1c 100644
@@ -8,6 +8,7 @@
  */
 #include <linux/io.h>
 #include <linux/of.h>
+#include <linux/dma-mapping.h>
 #include <linux/init.h>
 #include <linux/of_platform.h>
 #include <linux/of_address.h>
@@ -24,8 +25,6 @@
 
 #include "keystone.h"
 
-static unsigned long keystone_dma_pfn_offset __read_mostly;
-
 static int keystone_platform_notifier(struct notifier_block *nb,
 				      unsigned long event, void *data)
 {
@@ -38,9 +37,12 @@ static int keystone_platform_notifier(struct notifier_block *nb,
 		return NOTIFY_BAD;
 
 	if (!dev->of_node) {
-		dev->dma_pfn_offset = keystone_dma_pfn_offset;
-		dev_err(dev, "set dma_pfn_offset%08lx\n",
-			dev->dma_pfn_offset);
+		int ret = dma_set_offset_range(dev, KEYSTONE_HIGH_PHYS_START,
+					       KEYSTONE_LOW_PHYS_START,
+					       KEYSTONE_HIGH_PHYS_SIZE);
+		dev_err(dev, "set dma_offset%08llx%s\n",
+			KEYSTONE_HIGH_PHYS_START - KEYSTONE_LOW_PHYS_START,
+			ret ? " failed" : "");
 	}
 	return NOTIFY_OK;
 }
@@ -51,11 +53,8 @@ static struct notifier_block platform_nb = {
 
 static void __init keystone_init(void)
 {
-	if (PHYS_OFFSET >= KEYSTONE_HIGH_PHYS_START) {
-		keystone_dma_pfn_offset = PFN_DOWN(KEYSTONE_HIGH_PHYS_START -
-						   KEYSTONE_LOW_PHYS_START);
+	if (PHYS_OFFSET >= KEYSTONE_HIGH_PHYS_START)
 		bus_register_notifier(&platform_bus_type, &platform_nb);
-	}
 	keystone_pm_runtime_init();
 }
 
arch/sh/drivers/pci/pcie-sh7786.c +5 -4
index e0b568aaa701..e929f85c5038 100644
@@ -12,6 +12,7 @@
 #include <linux/io.h>
 #include <linux/async.h>
 #include <linux/delay.h>
+#include <linux/dma-mapping.h>
 #include <linux/slab.h>
 #include <linux/clk.h>
 #include <linux/sh_clk.h>
@@ -31,6 +32,8 @@ struct sh7786_pcie_port {
 static struct sh7786_pcie_port *sh7786_pcie_ports;
 static unsigned int nr_ports;
 static unsigned long dma_pfn_offset;
+size_t memsize;
+u64 memstart;
 
 static struct sh7786_pcie_hwops {
 	int (*core_init)(void);
@@ -301,7 +304,6 @@ static int __init pcie_init(struct sh7786_pcie_port *port)
 	struct pci_channel *chan = port->hose;
 	unsigned int data;
 	phys_addr_t memstart, memend;
-	size_t memsize;
 	int ret, i, win;
 
 	/* Begin initialization */
@@ -368,8 +370,6 @@ static int __init pcie_init(struct sh7786_pcie_port *port)
 	memstart = ALIGN_DOWN(memstart, memsize);
 	memsize = roundup_pow_of_two(memend - memstart);
 
-	dma_pfn_offset = memstart >> PAGE_SHIFT;
-
 	/*
 	 * If there's more than 512MB of memory, we need to roll over to
 	 * LAR1/LAMR1.
@@ -487,7 +487,8 @@ int pcibios_map_platform_irq(const struct pci_dev *pdev, u8 slot, u8 pin)
 
 void pcibios_bus_add_device(struct pci_dev *pdev)
 {
-	pdev->dev.dma_pfn_offset = dma_pfn_offset;
+	dma_set_offset_range(&pdev->dev, __pa(memory_start),
+			     __pa(memory_start) - memstart, memsize);
 }
 
 static int __init sh7786_pcie_core_init(void)
arch/sh/kernel/dma-coherent.c +6 -9
index d4811691b93c..003a91719b37 100644
@@ -14,6 +14,7 @@ void *arch_dma_alloc(struct device *dev, size_t size, dma_addr_t *dma_handle,
 {
 	void *ret, *ret_nocache;
 	int order = get_order(size);
+	phys_addr_t phys;
 
 	gfp |= __GFP_ZERO;
 
@@ -34,12 +35,10 @@ void *arch_dma_alloc(struct device *dev, size_t size, dma_addr_t *dma_handle,
 		return NULL;
 	}
 
-	split_page(pfn_to_page(virt_to_phys(ret) >> PAGE_SHIFT), order);
-
-	*dma_handle = virt_to_phys(ret);
-	if (!WARN_ON(!dev))
-		*dma_handle -= PFN_PHYS(dev->dma_pfn_offset);
+	phys = virt_to_phys(ret);
+	split_page(pfn_to_page(PHYS_PFN(phys)), order);
 
+	*dma_handle = (dma_addr_t)phys - dma_offset_from_phys_addr(dev, phys);
 	return ret_nocache;
 }
 
@@ -47,12 +46,10 @@ void arch_dma_free(struct device *dev, size_t size, void *vaddr,
 		dma_addr_t dma_handle, unsigned long attrs)
 {
 	int order = get_order(size);
-	unsigned long pfn = (dma_handle >> PAGE_SHIFT);
+	unsigned long pfn;
 	int k;
 
-	if (!WARN_ON(!dev))
-		pfn += dev->dma_pfn_offset;
-
+	pfn = PHYS_PFN(dma_handle + dma_offset_from_dma_addr(dev, dma_handle));
 	for (k = 0; k < (1 << order); k++)
 		__free_pages(pfn_to_page(pfn + k), 0);
 
arch/x86/pci/sta2x11-fixup.c +5 -2
index c313d784efab..ea3a58323f81 100644
@@ -12,6 +12,7 @@
 #include <linux/export.h>
 #include <linux/list.h>
 #include <linux/dma-direct.h>
+#include <linux/dma-mapping.h>
 #include <asm/iommu.h>
 
 #define STA2X11_SWIOTLB_SIZE (4*1024*1024)
@@ -133,7 +134,7 @@ static void sta2x11_map_ep(struct pci_dev *pdev)
 	struct sta2x11_instance *instance = sta2x11_pdev_to_instance(pdev);
 	struct device *dev = &pdev->dev;
 	u32 amba_base, max_amba_addr;
-	int i;
+	int i, ret;
 
 	if (!instance)
 		return;
@@ -141,7 +142,9 @@ static void sta2x11_map_ep(struct pci_dev *pdev)
 	pci_read_config_dword(pdev, AHB_BASE(0), &amba_base);
 	max_amba_addr = amba_base + STA2X11_AMBA_SIZE - 1;
 
-	dev->dma_pfn_offset = PFN_DOWN(-amba_base);
+	ret = dma_set_offset_range(dev, 0, amba_base, STA2X11_AMBA_SIZE);
+	if (ret)
+		dev_err(dev, "sta2x11: could not set DMA offset\n");
 
 	dev->bus_dma_limit = max_amba_addr;
 	pci_set_consistent_dma_mask(pdev, max_amba_addr);
drivers/acpi/arm64/iort.c +3 -2
index 28a6b387e80e..a3e04c003a21 100644
@@ -1142,8 +1142,9 @@ void iort_dma_setup(struct device *dev, u64 *dma_addr, u64 *dma_size)
 	*dma_addr = dmaaddr;
 	*dma_size = size;
 
-	dev->dma_pfn_offset = PFN_DOWN(offset);
-	dev_dbg(dev, "dma_pfn_offset(%#08llx)\n", offset);
+	ret = dma_set_offset_range(dev, dmaaddr + offset, dmaaddr, size);
+
+	dev_dbg(dev, "dma_offset(%#08llx)%s\n", offset, ret ? " failed!" : "");
 }
 
 static void __init acpi_iort_register_irq(int hwirq, const char *name,
drivers/gpu/drm/sun4i/sun4i_backend.c +4 -1
index 072ea113e6be..48a4adf1f04e 100644
@@ -11,6 +11,7 @@
 #include <linux/module.h>
 #include <linux/of_device.h>
 #include <linux/of_graph.h>
+#include <linux/dma-mapping.h>
 #include <linux/platform_device.h>
 #include <linux/reset.h>
 
@@ -812,7 +813,9 @@ static int sun4i_backend_bind(struct device *dev, struct device *master,
 		 * on our device since the RAM mapping is at 0 for the DMA bus,
 		 * unlike the CPU.
 		 */
-		drm->dev->dma_pfn_offset = PHYS_PFN_OFFSET;
+		ret = dma_set_offset_range(drm->dev, PHYS_OFFSET, 0, SZ_4G);
+		if (ret)
+			return ret;
 	}
 
 	backend->engine.node = dev->of_node;
drivers/iommu/io-pgtable-arm.c +1 -1
index 04fbd4bf0ff9..d5542df9aacc 100644
@@ -754,7 +754,7 @@ arm_lpae_alloc_pgtable(struct io_pgtable_cfg *cfg)
 	if (cfg->oas > ARM_LPAE_MAX_ADDR_BITS)
 		return NULL;
 
-	if (!selftest_running && cfg->iommu_dev->dma_pfn_offset) {
+	if (!selftest_running && cfg->iommu_dev->dma_range_map) {
 		dev_err(cfg->iommu_dev, "Cannot accommodate DMA offset for IOMMU page tables\n");
 		return NULL;
 	}
drivers/media/platform/sunxi/sun4i-csi/sun4i_csi.c +4 -1
index eff34ded6305..d6eda02fd3fc 100644
@@ -7,6 +7,7 @@
  */
 
 #include <linux/clk.h>
+#include <linux/dma-mapping.h>
 #include <linux/interrupt.h>
 #include <linux/module.h>
 #include <linux/mutex.h>
@@ -183,7 +184,9 @@ static int sun4i_csi_probe(struct platform_device *pdev)
 			return ret;
 	} else {
 #ifdef PHYS_PFN_OFFSET
-		csi->dev->dma_pfn_offset = PHYS_PFN_OFFSET;
+		ret = dma_set_offset_range(csi->dev, PHYS_OFFSET, 0, SZ_4G);
+		if (ret)
+			return ret;
 #endif
 	}
 
drivers/media/platform/sunxi/sun6i-csi/sun6i_csi.c +3 -1
index 055eb0b8e396..450fce6cd8d2 100644
@@ -898,7 +898,9 @@ static int sun6i_csi_probe(struct platform_device *pdev)
 
 	sdev->dev = &pdev->dev;
 	/* The DMA bus has the memory mapped at 0 */
-	sdev->dev->dma_pfn_offset = PHYS_OFFSET >> PAGE_SHIFT;
+	ret = dma_set_offset_range(sdev->dev, PHYS_OFFSET, 0, SZ_4G);
+	if (ret)
+		return ret;
 
 	ret = sun6i_csi_resource_request(sdev, pdev);
 	if (ret)
drivers/of/address.c +31 -40

108 lines not on this page · raw message

drivers/of/device.c +26 -17

93 lines not on this page · raw message

drivers/of/of_private.h +5 -5
index edc682249c00..5c13485a4ad1 100644
@@ -157,12 +157,12 @@ extern void __of_sysfs_remove_bin_file(struct device_node *np,
 extern int of_bus_n_addr_cells(struct device_node *np);
 extern int of_bus_n_size_cells(struct device_node *np);
 
-#ifdef CONFIG_OF_ADDRESS
-extern int of_dma_get_range(struct device_node *np, u64 *dma_addr,
-			    u64 *paddr, u64 *size);
+struct bus_dma_region;
+#if defined(CONFIG_OF_ADDRESS) && defined(CONFIG_HAS_DMA)
+int of_dma_get_range(struct device_node *np, const struct bus_dma_region **map);
 #else
-static inline int of_dma_get_range(struct device_node *np, u64 *dma_addr,
-				   u64 *paddr, u64 *size)
+static inline int of_dma_get_range(struct device_node *np,
+		const struct bus_dma_region **map)
 {
 	return -ENODEV;
 }
drivers/of/unittest.c +24 -8
index 398de04fd19c..a5ac52c994b2 100644
@@ -7,6 +7,7 @@
 
 #include <linux/memblock.h>
 #include <linux/clk.h>
+#include <linux/dma-mapping.h>
 #include <linux/err.h>
 #include <linux/errno.h>
 #include <linux/hashtable.h>
@@ -869,10 +870,10 @@ static void __init of_unittest_changeset(void)
 }
 
 static void __init of_unittest_dma_ranges_one(const char *path,
-		u64 expect_dma_addr, u64 expect_paddr, u64 expect_size)
+		u64 expect_dma_addr, u64 expect_paddr)
 {
 	struct device_node *np;
-	u64 dma_addr, paddr, size;
+	const struct bus_dma_region *map = NULL;
 	int rc;
 
 	np = of_find_node_by_path(path);
@@ -881,16 +882,28 @@ static void __init of_unittest_dma_ranges_one(const char *path,
 		return;
 	}
 
-	rc = of_dma_get_range(np, &dma_addr, &paddr, &size);
+	rc = of_dma_get_range(np, &map);
+	rc = PTR_ERR_OR_ZERO(map);
 
 	unittest(!rc, "of_dma_get_range failed on node %pOF rc=%i\n", np, rc);
+
 	if (!rc) {
-		unittest(size == expect_size,
-			 "of_dma_get_range wrong size on node %pOF size=%llx\n", np, size);
+		phys_addr_t	paddr;
+		dma_addr_t	dma_addr;
+		struct device	dev_bogus;
+
+		dev_bogus.dma_range_map = map;
+		paddr = (phys_addr_t)expect_dma_addr +
+			dma_offset_from_dma_addr(&dev_bogus, expect_dma_addr);
+		dma_addr = (dma_addr_t)expect_paddr -
+			dma_offset_from_phys_addr(&dev_bogus, expect_paddr);
+
 		unittest(paddr == expect_paddr,
 			 "of_dma_get_range wrong phys addr (%llx) on node %pOF", paddr, np);
 		unittest(dma_addr == expect_dma_addr,
 			 "of_dma_get_range wrong DMA addr (%llx) on node %pOF", dma_addr, np);
+
+		kfree(map);
 	}
 	of_node_put(np);
 }
@@ -898,11 +911,14 @@ static void __init of_unittest_dma_ranges_one(const char *path,
 static void __init of_unittest_parse_dma_ranges(void)
 {
 	of_unittest_dma_ranges_one("/testcase-data/address-tests/device@70000000",
-		0x0, 0x20000000, 0x40000000);
+		0x0, 0x20000000);
 	of_unittest_dma_ranges_one("/testcase-data/address-tests/bus@80000000/device@1000",
-		0x10000000, 0x20000000, 0x40000000);
+		0x10000000, 0x20000000);
+	/* pci@90000000 has two ranges in the dma-range property */
+	of_unittest_dma_ranges_one("/testcase-data/address-tests/pci@90000000",
+		0x80000000, 0x20000000);
 	of_unittest_dma_ranges_one("/testcase-data/address-tests/pci@90000000",
-		0x80000000, 0x20000000, 0x10000000);
+		0xc0000000, 0x40000000);
 }
 
 static void __init of_unittest_pci_dma_ranges(void)
drivers/pci/controller/pcie-brcmstb.c +1 -0
index bfc2542d54a8..8dacb9d3b7b6 100644
@@ -1197,6 +1197,7 @@ static int brcm_pcie_probe(struct platform_device *pdev)
 	ret = brcm_phy_start(pcie);
 	if (ret) {
 		dev_err(pcie->dev, "failed to start phy\n");
+		reset_control_assert(pcie->rescal);
 		return ret;
 	}
 
drivers/remoteproc/remoteproc_core.c +1 -1
index 9f04c30c4aaf..49242dd6176e 100644
@@ -519,7 +519,7 @@ static int rproc_handle_vdev(struct rproc *rproc, struct fw_rsc_vdev *rsc,
 	/* Initialise vdev subdevice */
 	snprintf(name, sizeof(name), "vdev%dbuffer", rvdev->index);
 	rvdev->dev.parent = &rproc->dev;
-	rvdev->dev.dma_pfn_offset = rproc->dev.parent->dma_pfn_offset;
+	rvdev->dev.dma_range_map = rproc->dev.parent->dma_range_map;
 	rvdev->dev.release = rproc_rvdev_release;
 	dev_set_name(&rvdev->dev, "%s#%s", dev_name(rvdev->dev.parent), name);
 	dev_set_drvdata(&rvdev->dev, rvdev);
drivers/staging/media/sunxi/cedrus/cedrus_hw.c +5 -2
index 1744e6fcc999..249e4bddaa40 100644
@@ -230,8 +230,11 @@ int cedrus_hw_probe(struct cedrus_dev *dev)
 	 */
 
 #ifdef PHYS_PFN_OFFSET
-	if (!(variant->quirks & CEDRUS_QUIRK_NO_DMA_OFFSET))
-		dev->dev->dma_pfn_offset = PHYS_PFN_OFFSET;
+	if (!(variant->quirks & CEDRUS_QUIRK_NO_DMA_OFFSET)) {
+		ret = dma_set_offset_range(dev->dev, PHYS_OFFSET, 0, SZ_4G);
+		if (ret)
+			return ret;
+	}
 #endif
 
 	ret = of_reserved_mem_device_init(dev->dev);
drivers/usb/core/message.c +2 -2
index 6197938dcc2d..376ca258e510 100644
@@ -1956,10 +1956,10 @@ int usb_set_configuration(struct usb_device *dev, int configuration)
 		intf->dev.groups = usb_interface_groups;
 		/*
 		 * Please refer to usb_alloc_dev() to see why we set
-		 * dma_mask and dma_pfn_offset.
+		 * dma_mask and dma_range_map.
 		 */
 		intf->dev.dma_mask = dev->dev.dma_mask;
-		intf->dev.dma_pfn_offset = dev->dev.dma_pfn_offset;
+		intf->dev.dma_range_map = dev->dev.dma_range_map;
 		INIT_WORK(&intf->reset_ws, __usb_queue_reset_device);
 		intf->minor = -1;
 		device_initialize(&intf->dev);
drivers/usb/core/usb.c +1 -1
index f16c26dc079d..1f167a2c095e 100644
@@ -611,7 +611,7 @@ struct usb_device *usb_alloc_dev(struct usb_device *parent,
 	 * mask for the entire HCD, so don't do that.
 	 */
 	dev->dev.dma_mask = bus->sysdev->dma_mask;
-	dev->dev.dma_pfn_offset = bus->sysdev->dma_pfn_offset;
+	dev->dev.dma_range_map = bus->sysdev->dma_range_map;
 	set_dev_node(&dev->dev, dev_to_node(bus->sysdev));
 	dev->state = USB_STATE_ATTACHED;
 	dev->lpm_disable_count = 1;
include/linux/device.h +2 -2
index 15460a5ac024..feddefcf3e5c 100644
@@ -492,7 +492,7 @@ struct dev_links_info {
  * 		such descriptors.
  * @bus_dma_limit: Limit of an upstream bridge or bus which imposes a smaller
  *		DMA limit than the device itself supports.
- * @dma_pfn_offset: offset of DMA memory range relatively of RAM
+ * @dma_range_map: map for DMA memory ranges relative to that of RAM
  * @dma_parms:	A low level driver may set these to teach IOMMU code about
  * 		segment limitations.
  * @dma_pools:	Dma pools (if dma'ble device).
@@ -577,7 +577,7 @@ struct device {
 					     64 bit addresses for consistent
 					     allocations such descriptors. */
 	u64		bus_dma_limit;	/* upstream dma constraint */
-	unsigned long	dma_pfn_offset;
+	const struct bus_dma_region *dma_range_map;
 
 	struct device_dma_parameters *dma_parms;
 
include/linux/dma-direct.h +2 -6
index cdfa400f89b3..79ce325b1e86 100644
@@ -13,16 +13,12 @@ extern unsigned int zone_dma_bits;
 #else
 static inline dma_addr_t __phys_to_dma(struct device *dev, phys_addr_t paddr)
 {
-	dma_addr_t dev_addr = (dma_addr_t)paddr;
-
-	return dev_addr - ((dma_addr_t)dev->dma_pfn_offset << PAGE_SHIFT);
+	return (dma_addr_t)paddr - dma_offset_from_phys_addr(dev, paddr);
 }
 
 static inline phys_addr_t __dma_to_phys(struct device *dev, dma_addr_t dev_addr)
 {
-	phys_addr_t paddr = (phys_addr_t)dev_addr;
-
-	return paddr + ((phys_addr_t)dev->dma_pfn_offset << PAGE_SHIFT);
+	return (phys_addr_t)dev_addr + dma_offset_from_dma_addr(dev, dev_addr);
 }
 #endif /* !CONFIG_ARCH_HAS_PHYS_TO_DMA */
 
include/linux/dma-mapping.h +34 -0
index 78f677cf45ab..69c1bbb4fc44 100644
@@ -255,7 +255,38 @@ static inline void dma_direct_sync_sg_for_cpu(struct device *dev,
 
 size_t dma_direct_max_mapping_size(struct device *dev);
 
+struct bus_dma_region {
+	phys_addr_t	cpu_start;
+	dma_addr_t	dma_start;
+	u64		size;
+	u64		offset;
+};
+
 #ifdef CONFIG_HAS_DMA
+static inline u64 dma_offset_from_dma_addr(struct device *dev, dma_addr_t dma_addr)
+{
+	const struct bus_dma_region *m = dev->dma_range_map;
+
+	if (!m)
+		return 0;
+	for (; m->size; m++)
+		if (dma_addr >= m->dma_start && dma_addr - m->dma_start < m->size)
+			return m->offset;
+	return 0;
+}
+
+static inline u64 dma_offset_from_phys_addr(struct device *dev, phys_addr_t paddr)
+{
+	const struct bus_dma_region *m = dev->dma_range_map;
+
+	if (!m)
+		return 0;
+	for (; m->size; m++)
+		if (paddr >= m->cpu_start && paddr - m->cpu_start < m->size)
+			return m->offset;
+	return 0;
+}
+
 #include <asm/dma-mapping.h>
 
 static inline const struct dma_map_ops *get_dma_ops(struct device *dev)
@@ -796,6 +827,9 @@ static inline void arch_teardown_dma_ops(struct device *dev)
 }
 #endif /* CONFIG_ARCH_HAS_TEARDOWN_DMA_OPS */
 
+int dma_set_offset_range(struct device *dev, phys_addr_t cpu_start,
+		dma_addr_t dma_start, u64 size);
+
 static inline unsigned int dma_get_max_seg_size(struct device *dev)
 {
 	if (dev->dma_parms && dev->dma_parms->max_segment_size)
kernel/dma/coherent.c +6 -4
index 2a0c4985f38e..2e0fd783e08f 100644
@@ -31,10 +31,12 @@ static inline struct dma_coherent_mem *dev_get_coherent_memory(struct device *de
 static inline dma_addr_t dma_get_device_base(struct device *dev,
 					     struct dma_coherent_mem * mem)
 {
-	if (mem->use_dev_dma_pfn_offset)
-		return (mem->pfn_base - dev->dma_pfn_offset) << PAGE_SHIFT;
-	else
-		return mem->device_base;
+	if (mem->use_dev_dma_pfn_offset) {
+		u64 base_addr = (u64)mem->pfn_base << PAGE_SHIFT;
+
+		return base_addr - dma_offset_from_phys_addr(dev, base_addr);
+	}
+	return mem->device_base;
 }
 
 static int dma_init_coherent_memory(phys_addr_t phys_addr,
kernel/dma/mapping.c +63 -0

72 lines not on this page · raw message

Signature · 6 lines
2.17.1

_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu
#9 lore raw

PATCH v9 6/12 PCI: brcmstb: Add bcm7278 PERST# support

In reply to Jim Quinlan

From: Jim Quinlan <[email protected]>

The PERST# bit was moved to a different register in 7278-type STB chips. In addition, the polarity of the bit was also changed; for other chips writing a 1 specified assert; for 7278-type chips, writing a 0 specifies assert.

Of course, PERST# is a PCIe asserted-low signal.

---
 drivers/pci/controller/pcie-brcmstb.c | 19 +++++++++++++++----
 1 file changed, 15 insertions(+), 4 deletions(-)
drivers/pci/controller/pcie-brcmstb.c +15 -4
index 7c148eb65170..e5e7f7d82eda 100644
@@ -83,6 +83,7 @@
 
 #define PCIE_MISC_PCIE_CTRL				0x4064
 #define  PCIE_MISC_PCIE_CTRL_PCIE_L23_REQUEST_MASK	0x1
+#define PCIE_MISC_PCIE_CTRL_PCIE_PERSTB_MASK		0x4
 
 #define PCIE_MISC_PCIE_STATUS				0x4068
 #define  PCIE_MISC_PCIE_STATUS_PCIE_PORT_MASK		0x80
@@ -685,9 +686,16 @@ static inline void brcm_pcie_perst_set(struct brcm_pcie *pcie, u32 val)
 {
 	u32 tmp;
 
-	tmp = readl(pcie->base + PCIE_RGR1_SW_INIT_1(pcie));
-	u32p_replace_bits(&tmp, val, PCIE_RGR1_SW_INIT_1_PERST_MASK);
-	writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1(pcie));
+	if (pcie->type == BCM7278) {
+		/* Perst bit has moved and assert value is 0 */
+		tmp = readl(pcie->base + PCIE_MISC_PCIE_CTRL);
+		u32p_replace_bits(&tmp, !val, PCIE_MISC_PCIE_CTRL_PCIE_PERSTB_MASK);
+		writel(tmp, pcie->base +  PCIE_MISC_PCIE_CTRL);
+	} else {
+		tmp = readl(pcie->base + PCIE_RGR1_SW_INIT_1(pcie));
+		u32p_replace_bits(&tmp, val, PCIE_RGR1_SW_INIT_1_PERST_MASK);
+		writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1(pcie));
+	}
 }
 
 static inline int brcm_pcie_get_rc_bar2_size_and_offset(struct brcm_pcie *pcie,
@@ -772,7 +780,10 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie)
 
 	/* Reset the bridge */
 	brcm_pcie_bridge_sw_init_set(pcie, 1);
-	brcm_pcie_perst_set(pcie, 1);
+
+	/* BCM7278 fails when PERST# is set here */
+	if (pcie->type != BCM7278)
+		brcm_pcie_perst_set(pcie, 1);
 
 	usleep_range(100, 200);
 
Signature · 1 line
2.17.1
#6 lore raw

PATCH v9 3/12 dt-bindings: PCI: Add bindings for more Brcmstb chips

In reply to Jim Quinlan

From: Jim Quinlan <[email protected]>

- Add compatible strings for three more Broadcom STB chips: 7278, 7216, 7211 (STB version of RPi4).
- Add new property 'brcm,scb-sizes'.
- Add new property 'resets'.
- Add new property 'reset-names' for 7216 only.
- Allow 'ranges' and 'dma-ranges' to have more than one item and update the example to show this.

---
 .../bindings/pci/brcm,stb-pcie.yaml           | 56 ++++++++++++++++---
 1 file changed, 49 insertions(+), 7 deletions(-)
Documentation/devicetree/bindings/pci/brcm,stb-pcie.yaml +49 -7
index 8680a0f86c5a..807694b4f41f 100644
@@ -9,12 +9,15 @@ title: Brcmstb PCIe Host Controller Device Tree Bindings
 maintainers:
   - Nicolas Saenz Julienne <[email protected]>
 
-allOf:
-  - $ref: /schemas/pci/pci-bus.yaml#
-
 properties:
   compatible:
-    const: brcm,bcm2711-pcie # The Raspberry Pi 4
+    items:
+      - enum:
+          - brcm,bcm2711-pcie # The Raspberry Pi 4
+          - brcm,bcm7211-pcie # Broadcom STB version of RPi4
+          - brcm,bcm7278-pcie # Broadcom 7278 Arm
+          - brcm,bcm7216-pcie # Broadcom 7216 Arm
+          - brcm,bcm7445-pcie # Broadcom 7445 Arm
 
   reg:
     maxItems: 1
@@ -34,10 +37,12 @@ properties:
       - const: msi
 
   ranges:
-    maxItems: 1
+    minItems: 1
+    maxItems: 4
 
   dma-ranges:
-    maxItems: 1
+    minItems: 1
+    maxItems: 6
 
   clocks:
     maxItems: 1
@@ -58,8 +63,31 @@ properties:
 
   aspm-no-l0s: true
 
+  resets:
+    description: for "brcm,bcm7216-pcie", must be a valid reset
+      phandle pointing to the RESCAL reset controller provider node.
+    $ref: "/schemas/types.yaml#/definitions/phandle"
+
+  reset-names:
+    items:
+      - const: rescal
+
+  brcm,scb-sizes:
+    description: u64 giving the 64bit PCIe memory
+      viewport size of a memory controller.  There may be up to
+      three controllers, and each size must be a power of two
+      with a size greater or equal to the amount of memory the
+      controller supports.  Note that each memory controller
+      may have two component regions -- base and extended -- so
+      this information cannot be deduced from the dma-ranges.
+    $ref: /schemas/types.yaml#/definitions/uint64-array
+    items:
+      minItems: 1
+      maxItems: 3
+
 required:
   - reg
+  - ranges
   - dma-ranges
   - "#interrupt-cells"
   - interrupts
@@ -68,6 +96,18 @@ required:
   - interrupt-map
   - msi-controller
 
+allOf:
+  - $ref: /schemas/pci/pci-bus.yaml#
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: brcm,bcm7216-pcie
+    then:
+      required:
+        - resets
+        - reset-names
+
 unevaluatedProperties: false
 
 examples:
@@ -93,7 +133,9 @@ examples:
                     msi-parent = <&pcie0>;
                     msi-controller;
                     ranges = <0x02000000 0x0 0xf8000000 0x6 0x00000000 0x0 0x04000000>;
-                    dma-ranges = <0x02000000 0x0 0x00000000 0x0 0x00000000 0x0 0x80000000>;
+                    dma-ranges = <0x42000000 0x1 0x00000000 0x0 0x40000000 0x0 0x80000000>,
+                                 <0x42000000 0x1 0x80000000 0x3 0x00000000 0x0 0x80000000>;
                     brcm,enable-ssc;
+                    brcm,scb-sizes =  <0x0000000080000000 0x0000000080000000>;
             };
     };
Signature · 1 line
2.17.1
#2 lore raw

PATCH v9 2/12 ata: ahci_brcm: Fix use of BCM7216 reset controller

In reply to Jim Quinlan

From: Jim Quinlan <[email protected]>

A reset controller "rescal" is shared between the AHCI driver and the PCIe driver for the BrcmSTB 7216 chip. Use devm_reset_control_get_optional_shared() to handle this sharing.

Fixes 272ecd60a636 ("ata: ahci_brcm: BCM7216 reset is self de-asserting")
Fixes c345ec6a50e9 ("ata: ahci_brcm: Support BCM7216 reset controller name")
---
 drivers/ata/ahci_brcm.c | 11 +++--------
 1 file changed, 3 insertions(+), 8 deletions(-)
drivers/ata/ahci_brcm.c +3 -8
index 6853dbb4131d..d6115bc04b09 100644
@@ -428,7 +428,6 @@ static int brcm_ahci_probe(struct platform_device *pdev)
 {
 	const struct of_device_id *of_id;
 	struct device *dev = &pdev->dev;
-	const char *reset_name = NULL;
 	struct brcm_ahci_priv *priv;
 	struct ahci_host_priv *hpriv;
 	struct resource *res;
@@ -452,11 +451,10 @@ static int brcm_ahci_probe(struct platform_device *pdev)
 
 	/* Reset is optional depending on platform and named differently */
 	if (priv->version == BRCM_SATA_BCM7216)
-		reset_name = "rescal";
+		priv->rcdev = devm_reset_control_get_optional_shared(&pdev->dev, "rescal");
 	else
-		reset_name = "ahci";
+		priv->rcdev = devm_reset_control_get_optional(&pdev->dev, "ahci");
 
-	priv->rcdev = devm_reset_control_get_optional(&pdev->dev, reset_name);
 	if (IS_ERR(priv->rcdev))
 		return PTR_ERR(priv->rcdev);
 
@@ -479,10 +477,7 @@ static int brcm_ahci_probe(struct platform_device *pdev)
 		break;
 	}
 
-	if (priv->version == BRCM_SATA_BCM7216)
-		ret = reset_control_reset(priv->rcdev);
-	else
-		ret = reset_control_deassert(priv->rcdev);
+	ret = reset_control_deassert(priv->rcdev);
 	if (ret)
 		return ret;
 
Signature · 1 line
2.17.1
#30 lore raw

PATCH v9 10/12 PCI: brcmstb: Accommodate MSI for older chips

In reply to Jim Quinlan

From: Jim Quinlan <[email protected]>

Older BrcmSTB chips do not have a separate register for MSI interrupts; the MSIs are in a register that also contains unrelated interrupts. In addition, the interrupts lie in bits [31..24] for these legacy chips. This commit provides common code for both legacy and non-legacy MSI interrupt registers.

---
 drivers/pci/controller/pcie-brcmstb.c | 71 +++++++++++++++++++--------
 1 file changed, 50 insertions(+), 21 deletions(-)
drivers/pci/controller/pcie-brcmstb.c +50 -21
index 3ef2d37cc43b..a2e02b2fbd36 100644
@@ -82,7 +82,8 @@
 #define PCIE_MISC_MSI_BAR_CONFIG_HI			0x4048
 
 #define PCIE_MISC_MSI_DATA_CONFIG			0x404c
-#define  PCIE_MISC_MSI_DATA_CONFIG_VAL			0xffe06540
+#define  PCIE_MISC_MSI_DATA_CONFIG_VAL_32		0xffe06540
+#define  PCIE_MISC_MSI_DATA_CONFIG_VAL_8		0xfff86540
 
 #define PCIE_MISC_PCIE_CTRL				0x4064
 #define  PCIE_MISC_PCIE_CTRL_PCIE_L23_REQUEST_MASK	0x1
@@ -94,6 +95,9 @@
 #define  PCIE_MISC_PCIE_STATUS_PCIE_PHYLINKUP_MASK	0x10
 #define  PCIE_MISC_PCIE_STATUS_PCIE_LINK_IN_L23_MASK	0x40
 
+#define PCIE_MISC_REVISION				0x406c
+#define  BRCM_PCIE_HW_REV_33				0x0303
+
 #define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT		0x4070
 #define  PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT_LIMIT_MASK	0xfff00000
 #define  PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT_BASE_MASK	0xfff0
@@ -114,10 +118,14 @@
 #define  PCIE_MISC_HARD_PCIE_HARD_DEBUG_CLKREQ_DEBUG_ENABLE_MASK	0x2
 #define  PCIE_MISC_HARD_PCIE_HARD_DEBUG_SERDES_IDDQ_MASK		0x08000000
 
-#define PCIE_MSI_INTR2_STATUS				0x4500
-#define PCIE_MSI_INTR2_CLR				0x4508
-#define PCIE_MSI_INTR2_MASK_SET				0x4510
-#define PCIE_MSI_INTR2_MASK_CLR				0x4514
+
+#define PCIE_INTR2_CPU_BASE		0x4300
+#define PCIE_MSI_INTR2_BASE		0x4500
+/* Offsets from PCIE_INTR2_CPU_BASE and PCIE_MSI_INTR2_BASE */
+#define  MSI_INT_STATUS			0x0
+#define  MSI_INT_CLR			0x8
+#define  MSI_INT_MASK_SET		0x10
+#define  MSI_INT_MASK_CLR		0x14
 
 #define PCIE_EXT_CFG_DATA				0x8000
 
@@ -132,6 +140,8 @@
 /* PCIe parameters */
 #define BRCM_NUM_PCIE_OUT_WINS		0x4
 #define BRCM_INT_PCI_MSI_NR		32
+#define BRCM_INT_PCI_MSI_LEGACY_NR	8
+#define BRCM_INT_PCI_MSI_SHIFT		0
 
 /* MSI target adresses */
 #define BRCM_MSI_TARGET_ADDR_LT_4GB	0x0fffffffcULL
@@ -246,6 +256,12 @@ struct brcm_msi {
 	int			irq;
 	/* used indicates which MSI interrupts have been alloc'd */
 	unsigned long		used;
+	bool			legacy;
+	/* Some chips have MSIs in bits [31..24] of a shared register. */
+	int			legacy_shift;
+	int			nr; /* No. of MSI available, depends on chip */
+	/* This is the base pointer for interrupt status/set/clr regs */
+	void __iomem		*intr_base;
 };
 
 /* Internal PCIe Host Controller Information.*/
@@ -265,6 +281,7 @@ struct brcm_pcie {
 	struct reset_control	*rescal;
 	int			num_memc;
 	u64			memc_size[PCIE_BRCM_MAX_MEMC];
+	u32			hw_rev;
 };
 
 /*
@@ -455,8 +472,10 @@ static void brcm_pcie_msi_isr(struct irq_desc *desc)
 	msi = irq_desc_get_handler_data(desc);
 	dev = msi->dev;
 
-	status = readl(msi->base + PCIE_MSI_INTR2_STATUS);
-	for_each_set_bit(bit, &status, BRCM_INT_PCI_MSI_NR) {
+	status = readl(msi->intr_base + MSI_INT_STATUS);
+	status >>= msi->legacy_shift;
+
+	for_each_set_bit(bit, &status, msi->nr) {
 		virq = irq_find_mapping(msi->inner_domain, bit);
 		if (virq)
 			generic_handle_irq(virq);
@@ -473,7 +492,7 @@ static void brcm_msi_compose_msi_msg(struct irq_data *data, struct msi_msg *msg)
 
 	msg->address_lo = lower_32_bits(msi->target_addr);
 	msg->address_hi = upper_32_bits(msi->target_addr);
-	msg->data = (0xffff & PCIE_MISC_MSI_DATA_CONFIG_VAL) | data->hwirq;
+	msg->data = (0xffff & PCIE_MISC_MSI_DATA_CONFIG_VAL_32) | data->hwirq;
 }
 
 static int brcm_msi_set_affinity(struct irq_data *irq_data,
@@ -485,8 +504,9 @@ static int brcm_msi_set_affinity(struct irq_data *irq_data,
 static void brcm_msi_ack_irq(struct irq_data *data)
 {
 	struct brcm_msi *msi = irq_data_get_irq_chip_data(data);
+	const int shift_amt = data->hwirq + msi->legacy_shift;
 
-	writel(1 << data->hwirq, msi->base + PCIE_MSI_INTR2_CLR);
+	writel(1 << shift_amt, msi->intr_base + MSI_INT_CLR);
 }
 
 
@@ -502,7 +522,7 @@ static int brcm_msi_alloc(struct brcm_msi *msi)
 	int hwirq;
 
 	mutex_lock(&msi->lock);
-	hwirq = bitmap_find_free_region(&msi->used, BRCM_INT_PCI_MSI_NR, 0);
+	hwirq = bitmap_find_free_region(&msi->used, msi->nr, 0);
 	mutex_unlock(&msi->lock);
 
 	return hwirq;
@@ -551,8 +571,7 @@ static int brcm_allocate_domains(struct brcm_msi *msi)
 	struct fwnode_handle *fwnode = of_node_to_fwnode(msi->np);
 	struct device *dev = msi->dev;
 
-	msi->inner_domain = irq_domain_add_linear(NULL, BRCM_INT_PCI_MSI_NR,
-						  &msi_domain_ops, msi);
+	msi->inner_domain = irq_domain_add_linear(NULL, msi->nr, &msi_domain_ops, msi);
 	if (!msi->inner_domain) {
 		dev_err(dev, "failed to create IRQ domain\n");
 		return -ENOMEM;
@@ -589,7 +608,10 @@ static void brcm_msi_remove(struct brcm_pcie *pcie)
 
 static void brcm_msi_set_regs(struct brcm_msi *msi)
 {
-	writel(0xffffffff, msi->base + PCIE_MSI_INTR2_MASK_CLR);
+	u32 val = __GENMASK(31, msi->legacy_shift);
+
+	writel(val, msi->intr_base + MSI_INT_MASK_CLR);
+	writel(val, msi->intr_base + MSI_INT_CLR);
 
 	/*
 	 * The 0 bit of PCIE_MISC_MSI_BAR_CONFIG_LO is repurposed to MSI
@@ -600,8 +622,8 @@ static void brcm_msi_set_regs(struct brcm_msi *msi)
 	writel(upper_32_bits(msi->target_addr),
 	       msi->base + PCIE_MISC_MSI_BAR_CONFIG_HI);
 
-	writel(PCIE_MISC_MSI_DATA_CONFIG_VAL,
-	       msi->base + PCIE_MISC_MSI_DATA_CONFIG);
+	val = msi->legacy ? PCIE_MISC_MSI_DATA_CONFIG_VAL_8 : PCIE_MISC_MSI_DATA_CONFIG_VAL_32;
+	writel(val, msi->base + PCIE_MISC_MSI_DATA_CONFIG);
 }
 
 static int brcm_pcie_enable_msi(struct brcm_pcie *pcie)
@@ -626,6 +648,17 @@ static int brcm_pcie_enable_msi(struct brcm_pcie *pcie)
 	msi->np = pcie->np;
 	msi->target_addr = pcie->msi_target_addr;
 	msi->irq = irq;
+	msi->legacy = pcie->hw_rev < BRCM_PCIE_HW_REV_33;
+
+	if (msi->legacy) {
+		msi->intr_base = msi->base + PCIE_INTR2_CPU_BASE;
+		msi->nr = BRCM_INT_PCI_MSI_LEGACY_NR;
+		msi->legacy_shift = 24;
+	} else {
+		msi->intr_base = msi->base + PCIE_MSI_INTR2_BASE;
+		msi->nr = BRCM_INT_PCI_MSI_NR;
+		msi->legacy_shift = 0;
+	}
 
 	ret = brcm_allocate_domains(msi);
 	if (ret)
@@ -888,12 +921,6 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie)
 	tmp &= ~PCIE_MISC_RC_BAR3_CONFIG_LO_SIZE_MASK;
 	writel(tmp, base + PCIE_MISC_RC_BAR3_CONFIG_LO);
 
-	/* Mask all interrupts since we are not handling any yet */
-	writel(0xffffffff, pcie->base + PCIE_MSI_INTR2_MASK_SET);
-
-	/* clear any interrupts we find on boot */
-	writel(0xffffffff, pcie->base + PCIE_MSI_INTR2_CLR);
-
 	if (pcie->gen)
 		brcm_pcie_set_gen(pcie, pcie->gen);
 
@@ -1237,6 +1264,8 @@ static int brcm_pcie_probe(struct platform_device *pdev)
 	if (ret)
 		goto fail;
 
+	pcie->hw_rev = readl(pcie->base + PCIE_MISC_REVISION);
+
 	msi_np = of_parse_phandle(pcie->np, "msi-parent", 0);
 	if (pci_msi_enabled() && msi_np == pcie->np) {
 		ret = brcm_pcie_enable_msi(pcie);
Signature · 1 line
2.17.1
#10 lore raw

PATCH v9 7/12 PCI: brcmstb: Add control of rescal reset

In reply to Jim Quinlan

From: Jim Quinlan <[email protected]>

Some STB chips have a special purpose reset controller named RESCAL (reset calibration). The PCIe HW can now control RESCAL to start and stop its operation. On probe(), the RESCAL is deasserted and the driver goes through the sequence of setting registers and reading status in order to start the internal PHY that is required for the PCIe.

---
 drivers/pci/controller/pcie-brcmstb.c | 81 ++++++++++++++++++++++++++-
 1 file changed, 80 insertions(+), 1 deletion(-)
drivers/pci/controller/pcie-brcmstb.c +80 -1
index e5e7f7d82eda..bfc2542d54a8 100644
@@ -23,6 +23,7 @@
 #include <linux/of_platform.h>
 #include <linux/pci.h>
 #include <linux/printk.h>
+#include <linux/reset.h>
 #include <linux/sizes.h>
 #include <linux/slab.h>
 #include <linux/string.h>
@@ -158,6 +159,16 @@
 #define DATA_ADDR(pcie)			(pcie->reg_offsets[EXT_CFG_DATA])
 #define PCIE_RGR1_SW_INIT_1(pcie)	(pcie->reg_offsets[RGR1_SW_INIT_1])
 
+/* Rescal registers */
+#define PCIE_DVT_PMU_PCIE_PHY_CTRL				0xc700
+#define  PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_NFLDS			0x3
+#define  PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_DIG_RESET_MASK		0x4
+#define  PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_DIG_RESET_SHIFT	0x2
+#define  PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_RESET_MASK		0x2
+#define  PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_RESET_SHIFT		0x1
+#define  PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_PWRDN_MASK		0x1
+#define  PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_PWRDN_SHIFT		0x0
+
 enum {
 	RGR1_SW_INIT_1,
 	EXT_CFG_INDEX,
@@ -248,6 +259,7 @@ struct brcm_pcie {
 	const int		*reg_offsets;
 	const int		*reg_field_info;
 	enum pcie_type		type;
+	struct reset_control	*rescal;
 };
 
 /*
@@ -966,6 +978,47 @@ static void brcm_pcie_enter_l23(struct brcm_pcie *pcie)
 		dev_err(pcie->dev, "failed to enter low-power link state\n");
 }
 
+static int brcm_phy_cntl(struct brcm_pcie *pcie, const int start)
+{
+	static const u32 shifts[PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_NFLDS] = {
+		PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_PWRDN_SHIFT,
+		PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_RESET_SHIFT,
+		PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_DIG_RESET_SHIFT,};
+	static const u32 masks[PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_NFLDS] = {
+		PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_PWRDN_MASK,
+		PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_RESET_MASK,
+		PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_DIG_RESET_MASK,};
+	const int beg = start ? 0 : PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_NFLDS - 1;
+	const int end = start ? PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_NFLDS : -1;
+	u32 tmp, combined_mask = 0;
+	u32 val = !!start;
+	void __iomem *base = pcie->base;
+	int i;
+
+	for (i = beg; i != end; start ? i++ : i--) {
+		tmp = readl(base + PCIE_DVT_PMU_PCIE_PHY_CTRL);
+		tmp = (tmp & ~masks[i]) | ((val << shifts[i]) & masks[i]);
+		writel(tmp, base + PCIE_DVT_PMU_PCIE_PHY_CTRL);
+		usleep_range(50, 200);
+		combined_mask |= masks[i];
+	}
+
+	tmp = readl(base + PCIE_DVT_PMU_PCIE_PHY_CTRL);
+	val = start ? combined_mask : 0;
+
+	return (tmp & combined_mask) == val ? 0 : -EIO;
+}
+
+static inline int brcm_phy_start(struct brcm_pcie *pcie)
+{
+	return pcie->rescal ? brcm_phy_cntl(pcie, 1) : 0;
+}
+
+static inline int brcm_phy_stop(struct brcm_pcie *pcie)
+{
+	return pcie->rescal ? brcm_phy_cntl(pcie, 0) : 0;
+}
+
 static void brcm_pcie_turn_off(struct brcm_pcie *pcie)
 {
 	void __iomem *base = pcie->base;
@@ -993,11 +1046,15 @@ static void brcm_pcie_turn_off(struct brcm_pcie *pcie)
 static int brcm_pcie_suspend(struct device *dev)
 {
 	struct brcm_pcie *pcie = dev_get_drvdata(dev);
+	int ret;
 
 	brcm_pcie_turn_off(pcie);
+	ret = brcm_phy_stop(pcie);
+	if (ret)
+		dev_err(pcie->dev, "failed to stop phy\n");
 	clk_disable_unprepare(pcie->clk);
 
-	return 0;
+	return ret;
 }
 
 static int brcm_pcie_resume(struct device *dev)
@@ -1010,6 +1067,12 @@ static int brcm_pcie_resume(struct device *dev)
 	base = pcie->base;
 	clk_prepare_enable(pcie->clk);
 
+	ret = brcm_phy_start(pcie);
+	if (ret) {
+		dev_err(pcie->dev, "failed to start phy\n");
+		return ret;
+	}
+
 	/* Take bridge out of reset so we can access the SERDES reg */
 	brcm_pcie_bridge_sw_init_set(pcie, 0);
 
@@ -1035,6 +1098,9 @@ static void __brcm_pcie_remove(struct brcm_pcie *pcie)
 {
 	brcm_msi_remove(pcie);
 	brcm_pcie_turn_off(pcie);
+	if (brcm_phy_stop(pcie))
+		dev_err(pcie->dev, "failed to stop phy\n");
+	reset_control_assert(pcie->rescal);
 	clk_disable_unprepare(pcie->clk);
 }
 
@@ -1120,6 +1186,19 @@ static int brcm_pcie_probe(struct platform_device *pdev)
 		dev_err(&pdev->dev, "could not enable clock\n");
 		return ret;
 	}
+	pcie->rescal = devm_reset_control_get_optional_shared(&pdev->dev, "rescal");
+	if (IS_ERR(pcie->rescal))
+		return PTR_ERR(pcie->rescal);
+
+	ret = reset_control_deassert(pcie->rescal);
+	if (ret)
+		dev_err(&pdev->dev, "failed to deassert 'rescal'\n");
+
+	ret = brcm_phy_start(pcie);
+	if (ret) {
+		dev_err(pcie->dev, "failed to start phy\n");
+		return ret;
+	}
 
 	ret = brcm_pcie_setup(pcie);
 	if (ret)
Signature · 1 line
2.17.1
#31 lore raw

PATCH v9 11/12 PCI: brcmstb: Set bus max burst size by chip type

In reply to Jim Quinlan

From: Jim Quinlan <[email protected]>

The proper value of the parameter SCB_MAX_BURST_SIZE varies per chip. The 2711 family requires 128B whereas other devices can employ 512. The assignment is complicated by the fact that the values for this two-bit field have different meanings;

Value Type_Generic Type_7278

     00       Reserved         128B
     01           128B         256B
     10           256B         512B

11 512B Reserved

---
 drivers/pci/controller/pcie-brcmstb.c | 19 +++++++++++++++----
 1 file changed, 15 insertions(+), 4 deletions(-)
drivers/pci/controller/pcie-brcmstb.c +15 -4
index a2e02b2fbd36..87a6f51d821a 100644
@@ -55,7 +55,7 @@
 #define  PCIE_MISC_MISC_CTRL_SCB_ACCESS_EN_MASK		0x1000
 #define  PCIE_MISC_MISC_CTRL_CFG_READ_UR_MODE_MASK	0x2000
 #define  PCIE_MISC_MISC_CTRL_MAX_BURST_SIZE_MASK	0x300000
-#define  PCIE_MISC_MISC_CTRL_MAX_BURST_SIZE_128		0x0
+
 #define  PCIE_MISC_MISC_CTRL_SCB0_SIZE_MASK		0xf8000000
 #define  PCIE_MISC_MISC_CTRL_SCB1_SIZE_MASK		0x07c00000
 #define  PCIE_MISC_MISC_CTRL_SCB2_SIZE_MASK		0x0000001f
@@ -847,7 +847,7 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie)
 	int num_out_wins = 0;
 	u16 nlw, cls, lnksta;
 	int i, ret, memc;
-	u32 tmp, aspm_support;
+	u32 tmp, burst, aspm_support;
 
 	/* Reset the bridge */
 	brcm_pcie_bridge_sw_init_set(pcie, 1);
@@ -867,11 +867,22 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie)
 	/* Wait for SerDes to be stable */
 	usleep_range(100, 200);
 
+	/*
+	 * SCB_MAX_BURST_SIZE is a two bit field.  For GENERIC chips it
+	 * is encoded as 0=128, 1=256, 2=512, 3=Rsvd, for BCM7278 it
+	 * is encoded as 0=Rsvd, 1=128, 2=256, 3=512.
+	 */
+	if (pcie->type == BCM2711)
+		burst = 0x0; /* 128B */
+	else if (pcie->type == BCM7278)
+		burst = 0x3; /* 512 bytes */
+	else
+		burst = 0x2; /* 512 bytes */
+
 	/* Set SCB_MAX_BURST_SIZE, CFG_READ_UR_MODE, SCB_ACCESS_EN */
 	u32p_replace_bits(&tmp, 1, PCIE_MISC_MISC_CTRL_SCB_ACCESS_EN_MASK);
 	u32p_replace_bits(&tmp, 1, PCIE_MISC_MISC_CTRL_CFG_READ_UR_MODE_MASK);
-	u32p_replace_bits(&tmp, PCIE_MISC_MISC_CTRL_MAX_BURST_SIZE_128,
-			  PCIE_MISC_MISC_CTRL_MAX_BURST_SIZE_MASK);
+	u32p_replace_bits(&tmp, burst, PCIE_MISC_MISC_CTRL_MAX_BURST_SIZE_MASK);
 	writel(tmp, base + PCIE_MISC_MISC_CTRL);
 
 	ret = brcm_pcie_get_rc_bar2_size_and_offset(pcie, &rc_bar2_size,
Signature · 1 line
2.17.1
#1 lore raw

PATCH v9 1/12 PCI: brcmstb: PCIE_BRCMSTB depends on ARCH_BRCMSTB

In reply to Jim Quinlan

From: Jim Quinlan <[email protected]>

Have PCIE_BRCMSTB depend on ARCH_BRCMSTB. Also set the default value to ARCH_BRCMSTB.

---
 drivers/pci/controller/Kconfig | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/pci/controller/Kconfig +2 -1
index adddf21fa381..c165328d5fbb 100644
@@ -262,9 +262,10 @@ config VMD
 
 config PCIE_BRCMSTB
 	tristate "Broadcom Brcmstb PCIe host controller"
-	depends on ARCH_BCM2835 || COMPILE_TEST
+	depends on ARCH_BRCMSTB || ARCH_BCM2835 || COMPILE_TEST
 	depends on OF
 	depends on PCI_MSI_IRQ_DOMAIN
+	default ARCH_BRCMSTB
 	help
 	  Say Y here to enable PCIe host controller support for
 	  Broadcom STB based SoCs, like the Raspberry Pi 4.
Signature · 1 line
2.17.1
#27 lore raw

PATCH v9 9/12 PCI: brcmstb: Set additional internal memory DMA viewport sizes

In reply to Jim Quinlan

The Raspberry Pi (RPI) is currently the only chip using this driver (pcie-brcmstb.c). There, only one memory controller is used, without an extension region, and the SCB0 viewport size is set to the size of the first and only dma-range region. Other BrcmSTB SOCs have more complicated memory configurations that require setting additional viewport sizes.

BrcmSTB PCIe controllers are intimately connected to the memory controller(s) on the SOC. The SOC may have one to three memory controllers; they are indicated by the term SCBi. Each controller has a base region and an optional extension region. In physical memory, the base and extension regions of a controller are not adjacent, but in PCIe-space they are.

There is a "viewport" for each memory controller that allows DMA from endpoint devices. Each viewport's size must be set to a power of two, and that size must be equal to or larger than the amount of memory each controller supports which is the sum of base region and its optional extension. Further, the 1-3 viewports are also adjacent in PCIe-space.

Unfortunately the viewport sizes cannot be ascertained from the "dma-ranges" property so they have their own property, "brcm,scb-sizes". This is because dma-range information does not indicate what memory controller it is associated. For example, consider the following case where the size of one dma-range is 2GB and the second dma-range is 1GB:

/* Case 1: SCB0 size set to 4GB */
dma-range0: 2GB (from memc0-base)
dma-range1: 1GB (from memc0-extension)

/* Case 2: SCB0 size set to 2GB, SCB1 size set to 1GB */
dma-range0: 2GB (from memc0-base)
dma-range1: 1GB (from memc0-extension)

By just looking at the dma-ranges information, one cannot tell which situation applies. That is why an additional property is needed. Its length indicates the number of memory controllers being used and each value indicates the viewport size.

Note that the RPI DT does not have a "brcm,scb-sizes" property value, as it is assumed that it only requires one memory controller and no extension. So the optional use of "brcm,scb-sizes" will be backwards compatible.

One last layer of complexity exists: all of the viewports sizes must be added and rounded up to a power of two to determine what the "BAR" size is. Further, an offset must be given that indicates the base PCIe address of this "BAR". The use of the term BAR is typically associated with endpoint devices, and the term is used here because the PCIe HW may be used as an RC or an EP. In the former case, all of the system memory appears in a single "BAR" region in PCIe memory. As it turns out, BrcmSTB PCIe HW is rarely used in the EP role and its system of mapping memory is an artifact that requires multiple dma-ranges regions.

---
 drivers/pci/controller/pcie-brcmstb.c | 68 ++++++++++++++++++++-------
 1 file changed, 50 insertions(+), 18 deletions(-)
drivers/pci/controller/pcie-brcmstb.c +50 -18
index 8dacb9d3b7b6..3ef2d37cc43b 100644
@@ -57,6 +57,8 @@
 #define  PCIE_MISC_MISC_CTRL_MAX_BURST_SIZE_MASK	0x300000
 #define  PCIE_MISC_MISC_CTRL_MAX_BURST_SIZE_128		0x0
 #define  PCIE_MISC_MISC_CTRL_SCB0_SIZE_MASK		0xf8000000
+#define  PCIE_MISC_MISC_CTRL_SCB1_SIZE_MASK		0x07c00000
+#define  PCIE_MISC_MISC_CTRL_SCB2_SIZE_MASK		0x0000001f
 
 #define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LO		0x400c
 #define PCIE_MEM_WIN0_LO(win)	\
@@ -154,6 +156,7 @@
 #define SSC_STATUS_OFFSET		0x1
 #define SSC_STATUS_SSC_MASK		0x400
 #define SSC_STATUS_PLL_LOCK_MASK	0x800
+#define PCIE_BRCM_MAX_MEMC		3
 
 #define IDX_ADDR(pcie)			(pcie->reg_offsets[EXT_CFG_INDEX])
 #define DATA_ADDR(pcie)			(pcie->reg_offsets[EXT_CFG_DATA])
@@ -260,6 +263,8 @@ struct brcm_pcie {
 	const int		*reg_field_info;
 	enum pcie_type		type;
 	struct reset_control	*rescal;
+	int			num_memc;
+	u64			memc_size[PCIE_BRCM_MAX_MEMC];
 };
 
 /*
@@ -715,22 +720,44 @@ static inline int brcm_pcie_get_rc_bar2_size_and_offset(struct brcm_pcie *pcie,
 							u64 *rc_bar2_offset)
 {
 	struct pci_host_bridge *bridge = pci_host_bridge_from_priv(pcie);
-	struct device *dev = pcie->dev;
 	struct resource_entry *entry;
+	struct device *dev = pcie->dev;
+	u64 lowest_pcie_addr = ~(u64)0;
+	int ret, i = 0;
+	u64 size = 0;
 
-	entry = resource_list_first_type(&bridge->dma_ranges, IORESOURCE_MEM);
-	if (!entry)
-		return -ENODEV;
+	resource_list_for_each_entry(entry, &bridge->dma_ranges) {
+		u64 pcie_beg = entry->res->start - entry->offset;
 
+		size += entry->res->end - entry->res->start + 1;
+		if (pcie_beg < lowest_pcie_addr)
+			lowest_pcie_addr = pcie_beg;
+	}
 
-	/*
-	 * The controller expects the inbound window offset to be calculated as
-	 * the difference between PCIe's address space and CPU's. The offset
-	 * provided by the firmware is calculated the opposite way, so we
-	 * negate it.
-	 */
-	*rc_bar2_offset = -entry->offset;
-	*rc_bar2_size = 1ULL << fls64(entry->res->end - entry->res->start);
+	if (lowest_pcie_addr == ~(u64)0) {
+		dev_err(dev, "DT node has no dma-ranges\n");
+		return -EINVAL;
+	}
+
+	ret = of_property_read_variable_u64_array(pcie->np, "brcm,scb-sizes", pcie->memc_size, 1,
+						  PCIE_BRCM_MAX_MEMC);
+
+	if (ret <= 0) {
+		/* Make an educated guess */
+		pcie->num_memc = 1;
+		pcie->memc_size[0] = 1 << fls64(size - 1);
+	} else {
+		pcie->num_memc = ret;
+	}
+
+	/* Each memc is viewed through a "port" that is a power of 2 */
+	for (i = 0, size = 0; i < pcie->num_memc; i++)
+		size += pcie->memc_size[i];
+
+	/* System memory starts at this address in PCIe-space */
+	*rc_bar2_offset = lowest_pcie_addr;
+	/* The sum of all memc views must also be a power of 2 */
+	*rc_bar2_size = 1ULL << fls64(size - 1);
 
 	/*
 	 * We validate the inbound memory view even though we should trust
@@ -782,12 +809,11 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie)
 	void __iomem *base = pcie->base;
 	struct device *dev = pcie->dev;
 	struct resource_entry *entry;
-	unsigned int scb_size_val;
 	bool ssc_good = false;
 	struct resource *res;
 	int num_out_wins = 0;
 	u16 nlw, cls, lnksta;
-	int i, ret;
+	int i, ret, memc;
 	u32 tmp, aspm_support;
 
 	/* Reset the bridge */
@@ -827,11 +853,17 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie)
 	writel(upper_32_bits(rc_bar2_offset),
 	       base + PCIE_MISC_RC_BAR2_CONFIG_HI);
 
-	scb_size_val = rc_bar2_size ?
-		       ilog2(rc_bar2_size) - 15 : 0xf; /* 0xf is 1GB */
 	tmp = readl(base + PCIE_MISC_MISC_CTRL);
-	u32p_replace_bits(&tmp, scb_size_val,
-			  PCIE_MISC_MISC_CTRL_SCB0_SIZE_MASK);
+	for (memc = 0; memc < pcie->num_memc; memc++) {
+		u32 scb_size_val = ilog2(pcie->memc_size[memc]) - 15;
+
+		if (memc == 0)
+			u32p_replace_bits(&tmp, scb_size_val, PCIE_MISC_MISC_CTRL_SCB0_SIZE_MASK);
+		else if (memc == 1)
+			u32p_replace_bits(&tmp, scb_size_val, PCIE_MISC_MISC_CTRL_SCB1_SIZE_MASK);
+		else if (memc == 2)
+			u32p_replace_bits(&tmp, scb_size_val, PCIE_MISC_MISC_CTRL_SCB2_SIZE_MASK);
+	}
 	writel(tmp, base + PCIE_MISC_MISC_CTRL);
 
 	/*
Signature · 1 line
2.17.1
#3 lore raw

Re: [PATCH v9 02/12] ata: ahci_brcm: Fix use of BCM7216 reset controller

In reply to Jim Quinlan
Quoted 10 lines · Jim Quinlan

From: Jim Quinlan <[email protected]>

A reset controller "rescal" is shared between the AHCI driver and the PCIe driver for the BrcmSTB 7216 chip. Use devm_reset_control_get_optional_shared() to handle this sharing.

Fixes 272ecd60a636 ("ata: ahci_brcm: BCM7216 reset is self de-asserting")
Fixes c345ec6a50e9 ("ata: ahci_brcm: Support BCM7216 reset controller name")

Sorry for not noticing earlier, the Fixes tag should go above your Signed-off-by, and they do not require a new line.

I believe that you also need to call reset_control_deassert() in brcm_ahci_resume() for symmetry and finally you can really submit this independently from this patch series since it is a pure bug fix (even though it is unveiled by working on PCIe as they share the same rescal reset).

Thanks!

Quoted 43 lines
---
 drivers/ata/ahci_brcm.c | 11 +++--------
 1 file changed, 3 insertions(+), 8 deletions(-)
drivers/ata/ahci_brcm.c +3 -8
index 6853dbb4131d..d6115bc04b09 100644
@@ -428,7 +428,6 @@ static int brcm_ahci_probe(struct platform_device *pdev)
 {
 	const struct of_device_id *of_id;
 	struct device *dev = &pdev->dev;
-	const char *reset_name = NULL;
 	struct brcm_ahci_priv *priv;
 	struct ahci_host_priv *hpriv;
 	struct resource *res;
@@ -452,11 +451,10 @@ static int brcm_ahci_probe(struct platform_device *pdev)
 
 	/* Reset is optional depending on platform and named differently */
 	if (priv->version == BRCM_SATA_BCM7216)
-		reset_name = "rescal";
+		priv->rcdev = devm_reset_control_get_optional_shared(&pdev->dev, "rescal");
 	else
-		reset_name = "ahci";
+		priv->rcdev = devm_reset_control_get_optional(&pdev->dev, "ahci");
 
-	priv->rcdev = devm_reset_control_get_optional(&pdev->dev, reset_name);
 	if (IS_ERR(priv->rcdev))
 		return PTR_ERR(priv->rcdev);
 
@@ -479,10 +477,7 @@ static int brcm_ahci_probe(struct platform_device *pdev)
 		break;
 	}
 
-	if (priv->version == BRCM_SATA_BCM7216)
-		ret = reset_control_reset(priv->rcdev);
-	else
-		ret = reset_control_deassert(priv->rcdev);
+	ret = reset_control_deassert(priv->rcdev);
 	if (ret)
 		return ret;
 
Signature · 1 line
Florian
#4 lore raw

Re: [PATCH v9 02/12] ata: ahci_brcm: Fix use of BCM7216 reset controller

In reply to Jim Quinlan

Hello!

Quoted 8 lines · Jim Quinlan

From: Jim Quinlan <[email protected]>

A reset controller "rescal" is shared between the AHCI driver and the PCIe driver for the BrcmSTB 7216 chip. Use devm_reset_control_get_optional_shared() to handle this sharing.

Shouldn't break up the tag area with the empty lines.

Quoted 2 lines
Fixes 272ecd60a636 ("ata: ahci_brcm: BCM7216 reset is self de-asserting")
Fixes c345ec6a50e9 ("ata: ahci_brcm: Support BCM7216 reset controller name")

[...]

MBR, Sergei

#5 lore raw

Re: [PATCH v9 02/12] ata: ahci_brcm: Fix use of BCM7216 reset controller

In reply to Jim Quinlan

Hi Jim,

Quoted 27 lines · Jim Quinlan

From: Jim Quinlan <[email protected]>

A reset controller "rescal" is shared between the AHCI driver and the PCIe driver for the BrcmSTB 7216 chip. Use devm_reset_control_get_optional_shared() to handle this sharing.

Fixes 272ecd60a636 ("ata: ahci_brcm: BCM7216 reset is self de-asserting")
Fixes c345ec6a50e9 ("ata: ahci_brcm: Support BCM7216 reset controller name")
---
 drivers/ata/ahci_brcm.c | 11 +++--------
 1 file changed, 3 insertions(+), 8 deletions(-)
drivers/ata/ahci_brcm.c +0 -1
index 6853dbb4131d..d6115bc04b09 100644
@@ -428,7 +428,6 @@ static int brcm_ahci_probe(struct platform_device *pdev)
 {
 	const struct of_device_id *of_id;
 	struct device *dev = &pdev->dev;
-	const char *reset_name = NULL;
 	struct brcm_ahci_priv *priv;
 	struct ahci_host_priv *hpriv;
 	struct resource *res;

drivers/ata/ahci_brcm.c static int brcm_ahci_probe(struct platform_device *pdev) · line 456

Quoted 8 lines
drivers/ata/ahci_brcm.c +2 -2
@@ -452,11 +451,10 @@ static int brcm_ahci_probe(struct platform_device *pdev)
 
 	/* Reset is optional depending on platform and named differently */
 	if (priv->version == BRCM_SATA_BCM7216)
-		reset_name = "rescal";
+		priv->rcdev = devm_reset_control_get_optional_shared(&pdev->dev, "rescal");
 	else
-		reset_name = "ahci";
+		priv->rcdev = devm_reset_control_get_optional(&pdev->dev, "ahci");

Please use devm_reset_control_get_optional_exclusive() here.

Quoted 7 lines
drivers/ata/ahci_brcm.c +0 -1
-	priv->rcdev = devm_reset_control_get_optional(&pdev->dev, reset_name);
 	if (IS_ERR(priv->rcdev))
 		return PTR_ERR(priv->rcdev);
 
@@ -479,10 +477,7 @@ static int brcm_ahci_probe(struct platform_device *pdev)
 		break;

drivers/ata/ahci_brcm.c static int brcm_ahci_probe(struct platform_device *pdev) · line 483

Quoted 10 lines
drivers/ata/ahci_brcm.c +1 -4
 	}
 
-	if (priv->version == BRCM_SATA_BCM7216)
-		ret = reset_control_reset(priv->rcdev);
-	else
-		ret = reset_control_deassert(priv->rcdev);
+	ret = reset_control_deassert(priv->rcdev);
 	if (ret)
 		return ret;
 

Since you switch from _reset to _deassert/_assert here, I suspect you should also change the out_reset error path, and the suspend/resume functions accordingly.

regards
Philipp

#12 lore raw

Re: [PATCH v9 08/12] device core: Introduce DMA range map, supplanting dma_pfn_offset

In reply to Jim Quinlan

A few tiny nitpicks:

The subject should have the dma-mapping prefix, this doesn't really touch the device core.

drivers/of/unittest.c static void __init of_unittest_dma_ranges_one(const char *path, · line 886

Quoted 3 lines
drivers/of/unittest.c +2 -1
-	rc = of_dma_get_range(np, &dma_addr, &paddr, &size);
+	rc = of_dma_get_range(np, &map);
+	rc = PTR_ERR_OR_ZERO(map);

I don't think you need the PTR_ERR_OR_ZERO line here, of_dma_get_range returns the error.

kernel/dma/mapping.c unsigned long dma_get_merge_boundary(struct device *dev) · line 447

Quoted 8 lines
kernel/dma/mapping.c +8 -0
+int dma_set_offset_range(struct device *dev, phys_addr_t cpu_start,
+			 dma_addr_t dma_start, u64 size)
+{
+	struct bus_dma_region *map;
+	u64 offset = (u64)cpu_start - (u64)dma_start;
+
+	if (!dev)
+		return -ENODEV;

I don't think we need the NULL protection here, all DMA API calls expect a device.

kernel/dma/mapping.c unsigned long dma_get_merge_boundary(struct device *dev) · line 459

Quoted 12 lines
kernel/dma/mapping.c +12 -0
+	if (!offset)
+		return 0;
+
+	/*
+	 * See if a map already exists and we already encompass the new range:
+	 */
+	if (dev->dma_range_map) {
+		if (dma_range_overlaps(dev, cpu_start, dma_start, size, offset))
+			return 0;
+		dev_err(dev, "attempt to add conflicting DMA range to existing map\n");
+		return -EINVAL;
+	}

And here why do we need the overlap check at all? I'd be tempted to always return an error for this case.

What is the plan to merge this? Do you want all this to go into one tree, or get as many bits into the applicable trees for 5.9 and then finish up for 5.10? If the former I can apply it to the dma-mapping tree and just fix up the nitpicks.
_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu

#14 lore raw

Re: [PATCH v9 08/12] device core: Introduce DMA range map, supplanting dma_pfn_offset

In reply to Jim Quinlan
Quoted 20 lines · Jim Quinlan

The new field 'dma_range_map' in struct device is used to facilitate the use of single or multiple offsets between mapping regions of cpu addrs and dma addrs. It subsumes the role of "dev->dma_pfn_offset" which was only capable of holding a single uniform offset and had no region bounds checking.

The function of_dma_get_range() has been modified so that it takes a single argument -- the device node -- and returns a map, NULL, or an error code. The map is an array that holds the information regarding the DMA regions. Each range entry contains the address offset, the cpu_start address, the dma_start address, and the size of the region.

of_dma_configure() is the typical manner to set range offsets but there are a number of ad hoc assignments to "dev->dma_pfn_offset" in the kernel driver code. These cases now invoke the function dma_attach_offset_range(dev, cpu_addr, dma_addr, size).

---

[...]

Quoted 53 lines
drivers/of/address.c +12 -12
index 8eea3f6e29a4..4b718d199efe 100644
@@ -918,33 +918,33 @@ void __iomem *of_io_request_and_map(struct device_node *np, int index,
 }
 EXPORT_SYMBOL(of_io_request_and_map);
 
+#ifdef CONFIG_HAS_DMA
 /**
- * of_dma_get_range - Get DMA range info
+ * of_dma_get_range - Get DMA range info and put it into a map array
  * @np:                device node to get DMA range info
- * @dma_addr:  pointer to store initial DMA address of DMA range
- * @paddr:     pointer to store initial CPU address of DMA range
- * @size:      pointer to store size of DMA range
+ * @map:       dma range structure to return
  *
  * Look in bottom up direction for the first "dma-ranges" property
- * and parse it.
- *  dma-ranges format:
+ * and parse it.  Put the information into a DMA offset map array.
+ *
+ * dma-ranges format:
  *     DMA addr (dma_addr)     : naddr cells
  *     CPU addr (phys_addr_t)  : pna cells
  *     size                    : nsize cells
  *
- * It returns -ENODEV if "dma-ranges" property was not found
- * for this device in DT.
+ * It returns -ENODEV if "dma-ranges" property was not found for this
+ * device in the DT.
  */
-int of_dma_get_range(struct device_node *np, u64 *dma_addr, u64 *paddr, u64 *size)
+int of_dma_get_range(struct device_node *np, const struct bus_dma_region **map)
 {
        struct device_node *node = of_node_get(np);
        const __be32 *ranges = NULL;
-       int len;
-       int ret = 0;
        bool found_dma_ranges = false;
        struct of_range_parser parser;
        struct of_range range;
-       u64 dma_start = U64_MAX, dma_end = 0, dma_offset = 0;
+       struct bus_dma_region *r;
+       int len, num_ranges = 0;
+       int ret;
 
        while (node) {
                ranges = of_get_property(node, "dma-ranges", &len);
@@ -970,44 +970,35 @@ int of_dma_get_range(struct device_node *np, u64 *dma_addr, u64 *paddr, u64 *siz
        }
 

drivers/of/address.c int of_dma_get_range(struct device_node *np, u64 *dma_addr, u64 *paddr, u64 *siz · line 981

Quoted 10 lines
drivers/of/address.c +9 -0
        of_dma_range_parser_init(&parser, node);
+       for_each_of_range(&parser, &range)
+               num_ranges++;
+
+       of_dma_range_parser_init(&parser, node);
+
+       ret = -ENOMEM;
+       r = kcalloc(num_ranges + 1, sizeof(*r), GFP_KERNEL);
+       if (!r)
+               goto out;

AFAICT, you have the error cases covered, but you are leaking memory if the device is removed.

[...]

drivers/remoteproc/remoteproc_core.c static int rproc_handle_vdev(struct rproc *rproc, struct fw_rsc_vdev *rsc, · line 522

Quoted 10 lines
drivers/remoteproc/remoteproc_core.c +1 -1
index 9f04c30c4aaf..49242dd6176e 100644
@@ -519,7 +519,7 @@ static int rproc_handle_vdev(struct rproc *rproc, struct fw_rsc_vdev *rsc,
        /* Initialise vdev subdevice */
        snprintf(name, sizeof(name), "vdev%dbuffer", rvdev->index);
        rvdev->dev.parent = &rproc->dev;
-       rvdev->dev.dma_pfn_offset = rproc->dev.parent->dma_pfn_offset;
+       rvdev->dev.dma_range_map = rproc->dev.parent->dma_range_map;

But doing this means you can't just free the dma_range_map. You need to do a copy here or you'd have to refcount it. Or I suppose you could check if it the child has a different dma_range_map ptr than the parent.

Rob
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel

#15 lore raw

Re: [PATCH v9 08/12] device core: Introduce DMA range map, supplanting dma_pfn_offset

Quoted 78 lines · Rob Herring
Quoted 20 lines · Jim Quinlan

The new field 'dma_range_map' in struct device is used to facilitate the use of single or multiple offsets between mapping regions of cpu addrs and dma addrs. It subsumes the role of "dev->dma_pfn_offset" which was only capable of holding a single uniform offset and had no region bounds checking.

The function of_dma_get_range() has been modified so that it takes a single argument -- the device node -- and returns a map, NULL, or an error code. The map is an array that holds the information regarding the DMA regions. Each range entry contains the address offset, the cpu_start address, the dma_start address, and the size of the region.

of_dma_configure() is the typical manner to set range offsets but there are a number of ad hoc assignments to "dev->dma_pfn_offset" in the kernel driver code. These cases now invoke the function dma_attach_offset_range(dev, cpu_addr, dma_addr, size).

---

[...]

Quoted 53 lines
drivers/of/address.c +12 -12
index 8eea3f6e29a4..4b718d199efe 100644
@@ -918,33 +918,33 @@ void __iomem *of_io_request_and_map(struct device_node *np, int index,
 }
 EXPORT_SYMBOL(of_io_request_and_map);
 
+#ifdef CONFIG_HAS_DMA
 /**
- * of_dma_get_range - Get DMA range info
+ * of_dma_get_range - Get DMA range info and put it into a map array
  * @np:                device node to get DMA range info
- * @dma_addr:  pointer to store initial DMA address of DMA range
- * @paddr:     pointer to store initial CPU address of DMA range
- * @size:      pointer to store size of DMA range
+ * @map:       dma range structure to return
  *
  * Look in bottom up direction for the first "dma-ranges" property
- * and parse it.
- *  dma-ranges format:
+ * and parse it.  Put the information into a DMA offset map array.
+ *
+ * dma-ranges format:
  *     DMA addr (dma_addr)     : naddr cells
  *     CPU addr (phys_addr_t)  : pna cells
  *     size                    : nsize cells
  *
- * It returns -ENODEV if "dma-ranges" property was not found
- * for this device in DT.
+ * It returns -ENODEV if "dma-ranges" property was not found for this
+ * device in the DT.
  */
-int of_dma_get_range(struct device_node *np, u64 *dma_addr, u64 *paddr, u64 *size)
+int of_dma_get_range(struct device_node *np, const struct bus_dma_region **map)
 {
        struct device_node *node = of_node_get(np);
        const __be32 *ranges = NULL;
-       int len;
-       int ret = 0;
        bool found_dma_ranges = false;
        struct of_range_parser parser;
        struct of_range range;
-       u64 dma_start = U64_MAX, dma_end = 0, dma_offset = 0;
+       struct bus_dma_region *r;
+       int len, num_ranges = 0;
+       int ret;
 
        while (node) {
                ranges = of_get_property(node, "dma-ranges", &len);
@@ -970,44 +970,35 @@ int of_dma_get_range(struct device_node *np, u64 *dma_addr, u64 *paddr, u64 *siz
        }
 
Quoted 13 lines

drivers/of/address.c int of_dma_get_range(struct device_node *np, u64 *dma_addr, u64 *paddr, u64 *siz · line 981

Quoted 10 lines
drivers/of/address.c +9 -0
        of_dma_range_parser_init(&parser, node);
+       for_each_of_range(&parser, &range)
+               num_ranges++;
+
+       of_dma_range_parser_init(&parser, node);
+
+       ret = -ENOMEM;
+       r = kcalloc(num_ranges + 1, sizeof(*r), GFP_KERNEL);
+       if (!r)
+               goto out;

AFAICT, you have the error cases covered, but you are leaking memory if the device is removed.

Hi Rob,

I started using devm_kcalloc() but at least two reviewers convinced me to just use kcalloc(). In addition, when I was using devm_kcalloc() it was awkward because 'dev' is not available to this function.

It comes down to whether unbind/binding the device N times is actually a reasonable usage. As for my experience I've seen two cases: (1) my overnight "bind/unbind the PCIe RC driver" script, and we have a customer who does an unbind/bind as a hail mary to bring back life to their dead EP device. If the latter case happens repeatedly, there are bigger problems.

Quoted 4 lines

[...]
b

Quoted 15 lines

drivers/remoteproc/remoteproc_core.c static int rproc_handle_vdev(struct rproc *rproc, struct fw_rsc_vdev *rsc, · line 522

Quoted 10 lines
drivers/remoteproc/remoteproc_core.c +1 -1
index 9f04c30c4aaf..49242dd6176e 100644
@@ -519,7 +519,7 @@ static int rproc_handle_vdev(struct rproc *rproc, struct fw_rsc_vdev *rsc,
        /* Initialise vdev subdevice */
        snprintf(name, sizeof(name), "vdev%dbuffer", rvdev->index);
        rvdev->dev.parent = &rproc->dev;
-       rvdev->dev.dma_pfn_offset = rproc->dev.parent->dma_pfn_offset;
+       rvdev->dev.dma_range_map = rproc->dev.parent->dma_range_map;

But doing this means you can't just free the dma_range_map. You need to do a copy here or you'd have to refcount it. Or I suppose you could check if it the child has a different dma_range_map ptr than the parent.

I don't believe the code here attempts to free the dma_range_map or needs to. Assuming that we devm_kcalloc'd() the dev->dma_range_map -- which we are not currently doing -- my reasoning is that this device does not need to free anything since the dev->dma_range_map belongs to a device higher up in the bus hierarchy, and the lower device will be removed long before the higher device is removed and dev->dma_range_map goes away.

Regards,
Jim

Regards,
Jim

Quoted 3 lines

Rob

_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu

#13 lore raw

Re: [PATCH v9 08/12] device core: Introduce DMA range map, supplanting dma_pfn_offset

In reply to Christoph Hellwig

Hi Christoph,

Quoted 6 lines · Christoph Hellwig

A few tiny nitpicks:

The subject should have the dma-mapping prefix, this doesn't really touch the device core.

Quoted 6 lines

drivers/of/unittest.c static void __init of_unittest_dma_ranges_one(const char *path, · line 886

Quoted 3 lines
drivers/of/unittest.c +2 -1
-     rc = of_dma_get_range(np, &dma_addr, &paddr, &size);
+     rc = of_dma_get_range(np, &map);
+     rc = PTR_ERR_OR_ZERO(map);

I don't think you need the PTR_ERR_OR_ZERO line here, of_dma_get_range returns the error.

Yes, that link needs to be deleted.

Quoted 12 lines

kernel/dma/mapping.c unsigned long dma_get_merge_boundary(struct device *dev) · line 447

Quoted 9 lines
kernel/dma/mapping.c +8 -0
+int dma_set_offset_range(struct device *dev, phys_addr_t cpu_start,
+                      dma_addr_t dma_start, u64 size)hh
+{
+     struct bus_dma_region *map;
+     u64 offset = (u64)cpu_start - (u64)dma_start;
+
+     if (!dev)
+             return -ENODEV;

I don't think we need the NULL protection here, all DMA API calls expect a device.

Yes, your review-patch removed it but left the comment about the function returning -ENODEV. So I wasn't sure to leave it in or not.

Quoted 14 lines

kernel/dma/mapping.c unsigned long dma_get_merge_boundary(struct device *dev) · line 459

Quoted 13 lines
kernel/dma/mapping.c +12 -0
+     if (!offset)
+             return 0;
+
+     /*
+      * See if a map already exists and we already encompass the new range:
+      */
+     if (dev->dma_range_map) {
+             if (dma_range_overlaps(dev, cpu_start, dma_start, size, offset))
+                     return 0;
+             dev_err(dev, "attempt to add conflicting DMA range to existing map\n");
+             return -EINVAL;
+     }
Quoted 2 lines

And here why do we need the overlap check at all? I'd be tempted to always return an error for this case.

I believe the overlap check was your suggestion or at least in your review-patch? I'm fine with just returning an error.

Quoted 5 lines

What is the plan to merge this? Do you want all this to go into one tree, or get as many bits into the applicable trees for 5.9 and then finish up for 5.10? If the former I can apply it to the dma-mapping tree and just fix up the nitpicks.

Whatever you think is best -- I would be quite happy if you could
accept at least the "dma_range_map" commit. Of course I'd be most
happy if the entire patchset were accepted, but perhaps you can just apply the "dma_range_map" commit, and I will continue to bang away at getting the N-1 PCIe-related commits ack'd and accepted.

Thanks much!
Jim Quinlan
Broadcom STB
_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu

#16 lore raw

Re: [PATCH v9 08/12] device core: Introduce DMA range map, supplanting dma_pfn_offset

In reply to Jim Quinlan
Quoted 10 lines · Jim Quinlan

I started using devm_kcalloc() but at least two reviewers convinced me to just use kcalloc(). In addition, when I was using devm_kcalloc() it was awkward because 'dev' is not available to this function.

It comes down to whether unbind/binding the device N times is actually a reasonable usage. As for my experience I've seen two cases: (1) my overnight "bind/unbind the PCIe RC driver" script, and we have a customer who does an unbind/bind as a hail mary to bring back life to their dead EP device. If the latter case happens repeatedly, there are bigger problems.

We can't just leak the allocations. Do you have a pointer to the arguments against managed resources? I'm generally not a huge fan of the managed resources, but for a case like this they actually seem useful. If we don't use the managed resources we'll at leat need to explicitly free the resources when freeing the device.
_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu

#17 lore raw

Re: [PATCH v9 08/12] device core: Introduce DMA range map, supplanting dma_pfn_offset

Quoted 13 lines · Christoph Hellwig
Quoted 10 lines · Jim Quinlan

I started using devm_kcalloc() but at least two reviewers convinced me to just use kcalloc(). In addition, when I was using devm_kcalloc() it was awkward because 'dev' is not available to this function.

It comes down to whether unbind/binding the device N times is actually a reasonable usage. As for my experience I've seen two cases: (1) my overnight "bind/unbind the PCIe RC driver" script, and we have a customer who does an unbind/bind as a hail mary to bring back life to their dead EP device. If the latter case happens repeatedly, there are bigger problems.

Quoted 5 lines

We can't just leak the allocations. Do you have a pointer to the arguments against managed resources? I'm generally not a huge fan of the managed resources, but for a case like this they actually seem useful. If we don't use the managed resources we'll at leat need to explicitly free the resources when freeing the device.

Actually, there were no arguments for using an unmanaged kcalloc, just comments [1], [2]. When it was rightly suggested to have 'dev' dropped from of_dma_range() [3], I submitted v6 to accomplish this. But now of_dma_range() would call kcalloc(), and then of_dma_configure() was required to "dup" the result, requiring a devm_kcalloc(), memcpy(), and kfree(). This was awkward, so considering [1], [2], I dropped the devm_kcalloc() and submitted v7.

So I can easily revert to the awkward code of v6. But I'm hoping you have a more elegant solution :-)

Thanks,
Jim

[1]
[v6, Andy Shevchenko]

Review

Quoted 3 lines
(quoted diff) +3 -0
+             /* We want the offset map to be device-managed, so alloc & copy */
+             dev->dma_range_map = devm_kcalloc(dev, num_ranges + 1, sizeof(*r),
+                                               GFP_KERNEL);

The question is how many times per device lifetime this can be called?

[2]
[v2, Andy Shevchenko]

Quoted 1 line

+ r = devm_kzalloc(dev, r_size, GFP_KERNEL);

devm_?!
Looking at r_size it should be rather kcalloc().

[3]
[v3, Nicolas Saenz Julienne]

Quoted 11 lines

I agree with you. The reason I needed a "struct device *" in the call is because I wanted to make sure the memory that is alloc'd belongs to the device that needs it. If I do a regular kzalloc(), this memory will become a leak once someone starts unbinding/binding their device. Also, in all uses of of_dma_rtange() -- there is only one -- a dev is required as one can't attach an offset map to NULL.

I do see that there are a number of functions in drivers/of/*.c that take 'struct device *dev' as an argument so there is precedent for something like this. Regardless, I need an owner to the memory I alloc().

I understand the need for dev to be around, devm_*() is key. But also it's important to keep the functions on purpose. And if of_dma_get_range() starts setting ranges it calls, for the very least, for a function rename. Although I'd rather split the parsing and setting of ranges as mentioned earlier. That said, I get that's a more drastic move.
_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu

#18 lore raw

Re: [PATCH v9 08/12] device core: Introduce DMA range map, supplanting dma_pfn_offset

In reply to Christoph Hellwig
Quoted 13 lines · Christoph Hellwig
Quoted 10 lines · Jim Quinlan

I started using devm_kcalloc() but at least two reviewers convinced me to just use kcalloc(). In addition, when I was using devm_kcalloc() it was awkward because 'dev' is not available to this function.

It comes down to whether unbind/binding the device N times is actually a reasonable usage. As for my experience I've seen two cases: (1) my overnight "bind/unbind the PCIe RC driver" script, and we have a customer who does an unbind/bind as a hail mary to bring back life to their dead EP device. If the latter case happens repeatedly, there are bigger problems.

Quoted 5 lines

We can't just leak the allocations. Do you have a pointer to the arguments against managed resources? I'm generally not a huge fan of the managed resources, but for a case like this they actually seem useful. If we don't use the managed resources we'll at leat need to explicitly free the resources when freeing the device.

The lifetime for devm_kcalloc may not be what we want here. devm allocs are freed on probe fail or remove, not on freeing the device (there is a just in case free there too though).

Rob
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel

#19 lore raw

Re: [PATCH v9 08/12] device core: Introduce DMA range map, supplanting dma_pfn_offset

Quoted 21 lines · Rob Herring
Quoted 13 lines · Christoph Hellwig
Quoted 10 lines · Jim Quinlan

I started using devm_kcalloc() but at least two reviewers convinced me to just use kcalloc(). In addition, when I was using devm_kcalloc() it was awkward because 'dev' is not available to this function.

It comes down to whether unbind/binding the device N times is actually a reasonable usage. As for my experience I've seen two cases: (1) my overnight "bind/unbind the PCIe RC driver" script, and we have a customer who does an unbind/bind as a hail mary to bring back life to their dead EP device. If the latter case happens repeatedly, there are bigger problems.

Quoted 5 lines

We can't just leak the allocations. Do you have a pointer to the arguments against managed resources? I'm generally not a huge fan of the managed resources, but for a case like this they actually seem useful. If we don't use the managed resources we'll at leat need to explicitly free the resources when freeing the device.

Quoted 3 lines

The lifetime for devm_kcalloc may not be what we want here. devm allocs are freed on probe fail or remove, not on freeing the device (there is a just in case free there too though).

What do you suggest doing as an alternative?

Jim

Quoted 3 lines

Rob

_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu

#20 lore raw

Re: [PATCH v9 08/12] device core: Introduce DMA range map, supplanting dma_pfn_offset

Quoted 20 lines · Jim Quinlan
Quoted 19 lines · Rob Herring
Quoted 17 lines · Christoph Hellwig
Quoted 10 lines · Jim Quinlan

I started using devm_kcalloc() but at least two reviewers convinced me to just use kcalloc(). In addition, when I was using devm_kcalloc() it was awkward because 'dev' is not available to this function.

It comes down to whether unbind/binding the device N times is actually a reasonable usage. As for my experience I've seen two cases: (1) my overnight "bind/unbind the PCIe RC driver" script, and we have a customer who does an unbind/bind as a hail mary to bring back life to their dead EP device. If the latter case happens repeatedly, there are bigger problems.

We can't just leak the allocations. Do you have a pointer to the arguments against managed resources? I'm generally not a huge fan of the managed resources, but for a case like this they actually seem useful. If we don't use the managed resources we'll at leat need to explicitly free the resources when freeing the device.

Quoted 5 lines
Quoted 3 lines

The lifetime for devm_kcalloc may not be what we want here. devm allocs are freed on probe fail or remove, not on freeing the device (there is a just in case free there too though).

What do you suggest doing as an alternative?

I haven't given the idea much thought, but how about using a kref in the first element of your bus_dma_region array. It should be increased upon assigning it to a device and decreased it upon destroying it (triggering the free once it hits 0). It would take care of this memory leak, but also useful where you're sharing bus_dma_regions between devices.

Regards,
Nicolas

_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu

#22 lore raw

Re: [PATCH v9 08/12] device core: Introduce DMA range map, supplanting dma_pfn_offset

In reply to Jim Quinlan

Hi Jim,

drivers/pci/controller/pcie-brcmstb.c static int brcm_pcie_probe(struct platform_device *pdev) · line 1202

Quoted 12 lines · Jim Quinlan

static void __init of_unittest_pci_dma_ranges(void)

drivers/pci/controller/pcie-brcmstb.c +1 -0
index bfc2542d54a8..8dacb9d3b7b6 100644
@@ -1197,6 +1197,7 @@ static int brcm_pcie_probe(struct platform_device *pdev)
 	ret = brcm_phy_start(pcie);
 	if (ret) {
 		dev_err(pcie->dev, "failed to start phy\n");
+		reset_control_assert(pcie->rescal);
 		return ret;
 	}

I think this sneaked in from another patch.

Regards,
Nicolas

_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu

#23 lore raw

Re: [PATCH v9 08/12] device core: Introduce DMA range map, supplanting dma_pfn_offset

Quoted 4 lines · Nicolas Saenz Julienne

Hi Jim,

On Fri, 2020-07-24 at 16:33 -0400, Jim Quinlan wrote:

Quoted 14 lines

drivers/pci/controller/pcie-brcmstb.c static int brcm_pcie_probe(struct platform_device *pdev) · line 1202

Quoted 12 lines

static void __init of_unittest_pci_dma_ranges(void)

drivers/pci/controller/pcie-brcmstb.c +1 -0
index bfc2542d54a8..8dacb9d3b7b6 100644
@@ -1197,6 +1197,7 @@ static int brcm_pcie_probe(struct platform_device *pdev)
      ret = brcm_phy_start(pcie);
      if (ret) {
              dev_err(pcie->dev, "failed to start phy\n");
+             reset_control_assert(pcie->rescal);
              return ret;
      }

I think this sneaked in from another patch.

Thanks Nicolas. BTW, at some point will you be able to test my patchset on the RP4 to see if I broke anything?

Thanks again,
Jim

Quoted 4 lines

Regards,
Nicolas

_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu

#24 lore raw

Re: [PATCH v9 08/12] device core: Introduce DMA range map, supplanting dma_pfn_offset

Quoted 19 lines · Jim Quinlan
Quoted 17 lines · Nicolas Saenz Julienne

Hi Jim,

drivers/pci/controller/pcie-brcmstb.c static int brcm_pcie_probe(struct platform_device *pdev) · line 1202

Quoted 12 lines · Jim Quinlan

static void __init of_unittest_pci_dma_ranges(void)

drivers/pci/controller/pcie-brcmstb.c +1 -0
index bfc2542d54a8..8dacb9d3b7b6 100644
@@ -1197,6 +1197,7 @@ static int brcm_pcie_probe(struct platform_device *pdev)
      ret = brcm_phy_start(pcie);
      if (ret) {
              dev_err(pcie->dev, "failed to start phy\n");
+             reset_control_assert(pcie->rescal);
              return ret;
      }

I think this sneaked in from another patch.

Quoted 2 lines

Thanks Nicolas. BTW, at some point will you be able to test my patchset on the RP4 to see if I broke anything?

Yes of course, I'll have a go at it tomorrow.

Regards,
Nicolas

_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu

#21 lore raw

Re: [PATCH v9 08/12] device core: Introduce DMA range map, supplanting dma_pfn_offset

In reply to Jim Quinlan
Quoted 23 lines · Jim Quinlan
Quoted 21 lines · Rob Herring
Quoted 18 lines · Christoph Hellwig
Quoted 10 lines · Jim Quinlan

I started using devm_kcalloc() but at least two reviewers convinced me to just use kcalloc(). In addition, when I was using devm_kcalloc() it was awkward because 'dev' is not available to this function.

It comes down to whether unbind/binding the device N times is actually a reasonable usage. As for my experience I've seen two cases: (1) my overnight "bind/unbind the PCIe RC driver" script, and we have a customer who does an unbind/bind as a hail mary to bring back life to their dead EP device. If the latter case happens repeatedly, there are bigger problems.

We can't just leak the allocations. Do you have a pointer to the arguments against managed resources? I'm generally not a huge fan of the managed resources, but for a case like this they actually seem useful. If we don't use the managed resources we'll at leat need to explicitly free the resources when freeing the device.

Quoted 5 lines
Quoted 3 lines

The lifetime for devm_kcalloc may not be what we want here. devm allocs are freed on probe fail or remove, not on freeing the device (there is a just in case free there too though).

What do you suggest doing as an alternative?

I believe I gave it already. Put a kfree in the struct device release function. But you can't be passing the pointer from device to device if you go that route. You'd have to either copy the struct or check if it's the same as the parent's and skip the kfree in that case.

Rob
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel

#25 lore raw

Re: [PATCH v9 08/12] device core: Introduce DMA range map, supplanting dma_pfn_offset

In reply to Jim Quinlan

Hi Jim, here's some comments after testing your series against RPi4.

Quoted 19 lines · Jim Quinlan

The new field 'dma_range_map' in struct device is used to facilitate the use of single or multiple offsets between mapping regions of cpu addrs and dma addrs. It subsumes the role of "dev->dma_pfn_offset" which was only capable of holding a single uniform offset and had no region bounds checking.

The function of_dma_get_range() has been modified so that it takes a single argument -- the device node -- and returns a map, NULL, or an error code. The map is an array that holds the information regarding the DMA regions. Each range entry contains the address offset, the cpu_start address, the dma_start address, and the size of the region.

of_dma_configure() is the typical manner to set range offsets but there are a number of ad hoc assignments to "dev->dma_pfn_offset" in the kernel driver code. These cases now invoke the function dma_attach_offset_range(dev, cpu_addr, dma_addr, size).

---

[...]

Quoted 95 lines
drivers/of/address.c +29 -32
index 8eea3f6e29a4..4b718d199efe 100644
@@ -918,33 +918,33 @@ void __iomem *of_io_request_and_map(struct device_node *np, int index,
 }
 EXPORT_SYMBOL(of_io_request_and_map);
 
+#ifdef CONFIG_HAS_DMA
 /**
- * of_dma_get_range - Get DMA range info
+ * of_dma_get_range - Get DMA range info and put it into a map array
  * @np:		device node to get DMA range info
- * @dma_addr:	pointer to store initial DMA address of DMA range
- * @paddr:	pointer to store initial CPU address of DMA range
- * @size:	pointer to store size of DMA range
+ * @map:	dma range structure to return
  *
  * Look in bottom up direction for the first "dma-ranges" property
- * and parse it.
- *  dma-ranges format:
+ * and parse it.  Put the information into a DMA offset map array.
+ *
+ * dma-ranges format:
  *	DMA addr (dma_addr)	: naddr cells
  *	CPU addr (phys_addr_t)	: pna cells
  *	size			: nsize cells
  *
- * It returns -ENODEV if "dma-ranges" property was not found
- * for this device in DT.
+ * It returns -ENODEV if "dma-ranges" property was not found for this
+ * device in the DT.
  */
-int of_dma_get_range(struct device_node *np, u64 *dma_addr, u64 *paddr, u64 *size)
+int of_dma_get_range(struct device_node *np, const struct bus_dma_region **map)
 {
 	struct device_node *node = of_node_get(np);
 	const __be32 *ranges = NULL;
-	int len;
-	int ret = 0;
 	bool found_dma_ranges = false;
 	struct of_range_parser parser;
 	struct of_range range;
-	u64 dma_start = U64_MAX, dma_end = 0, dma_offset = 0;
+	struct bus_dma_region *r;
+	int len, num_ranges = 0;
+	int ret;
 
 	while (node) {
 		ranges = of_get_property(node, "dma-ranges", &len);
@@ -970,44 +970,35 @@ int of_dma_get_range(struct device_node *np, u64 *dma_addr, u64 *paddr, u64 *siz
 	}
 
 	of_dma_range_parser_init(&parser, node);
+	for_each_of_range(&parser, &range)
+		num_ranges++;
+
+	of_dma_range_parser_init(&parser, node);
+
+	ret = -ENOMEM;
+	r = kcalloc(num_ranges + 1, sizeof(*r), GFP_KERNEL);
+	if (!r)
+		goto out;
 
+	/*
+	 * Record all info in the generic DMA ranges array for struct device.
+	 */
+	*map = r;
 	for_each_of_range(&parser, &range) {
 		pr_debug("dma_addr(%llx) cpu_addr(%llx) size(%llx)\n",
 			 range.bus_addr, range.cpu_addr, range.size);
-
-		if (dma_offset && range.cpu_addr - range.bus_addr != dma_offset) {
-			pr_warn("Can't handle multiple dma-ranges with different offsets on node(%pOF)\n", node);
-			/* Don't error out as we'd break some existing DTs */
-			continue;
-		}
-		dma_offset = range.cpu_addr - range.bus_addr;
-
-		/* Take lower and upper limits */
-		if (range.bus_addr < dma_start)
-			dma_start = range.bus_addr;
-		if (range.bus_addr + range.size > dma_end)
-			dma_end = range.bus_addr + range.size;
-	}
-
-	if (dma_start >= dma_end) {
-		ret = -EINVAL;
-		pr_debug("Invalid DMA ranges configuration on node(%pOF)\n",
-			 node);
-		goto out;
+		r->cpu_start = range.cpu_addr;
+		r->dma_start = range.bus_addr;
+		r->size = range.size;
+		r->offset = (u64)range.cpu_addr - (u64)range.bus_addr;

drivers/of/address.c int of_dma_get_range(struct device_node *np, u64 *dma_addr, u64 *paddr, u64 *siz · line 1005

Quoted 10 lines
drivers/of/address.c +1 -7
+		r++;
 	}
 
-	*dma_addr = dma_start;
-	*size = dma_end - dma_start;
-	*paddr = dma_start + dma_offset;
-
-	pr_debug("final: dma_addr(%llx) cpu_addr(%llx) size(%llx)\n",
-		 *dma_addr, *paddr, *size);
-

I think you're missing here:

	ret = 0;

drivers/of/address.c int of_dma_get_range(struct device_node *np, u64 *dma_addr, u64 *paddr, u64 *siz · line 1000

Quoted 5 lines
drivers/of/address.c +0 -1
 out:
 	of_node_put(node);
-
 	return ret;
 }

Regards,
Nicolas

_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu

#28 lore raw

Re: [PATCH v9 09/12] PCI: brcmstb: Set additional internal memory DMA viewport sizes

In reply to Jim Quinlan

Hi Jim,

Quoted 95 lines · Jim Quinlan

The Raspberry Pi (RPI) is currently the only chip using this driver (pcie-brcmstb.c). There, only one memory controller is used, without an extension region, and the SCB0 viewport size is set to the size of the first and only dma-range region. Other BrcmSTB SOCs have more complicated memory configurations that require setting additional viewport sizes.

BrcmSTB PCIe controllers are intimately connected to the memory controller(s) on the SOC. The SOC may have one to three memory controllers; they are indicated by the term SCBi. Each controller has a base region and an optional extension region. In physical memory, the base and extension regions of a controller are not adjacent, but in PCIe-space they are.

There is a "viewport" for each memory controller that allows DMA from endpoint devices. Each viewport's size must be set to a power of two, and that size must be equal to or larger than the amount of memory each controller supports which is the sum of base region and its optional extension. Further, the 1-3 viewports are also adjacent in PCIe-space.

Unfortunately the viewport sizes cannot be ascertained from the "dma-ranges" property so they have their own property, "brcm,scb-sizes". This is because dma-range information does not indicate what memory controller it is associated. For example, consider the following case where the size of one dma-range is 2GB and the second dma-range is 1GB:

/* Case 1: SCB0 size set to 4GB */
dma-range0: 2GB (from memc0-base)
dma-range1: 1GB (from memc0-extension)

/* Case 2: SCB0 size set to 2GB, SCB1 size set to 1GB */
dma-range0: 2GB (from memc0-base)
dma-range1: 1GB (from memc0-extension)

By just looking at the dma-ranges information, one cannot tell which situation applies. That is why an additional property is needed. Its length indicates the number of memory controllers being used and each value indicates the viewport size.

Note that the RPI DT does not have a "brcm,scb-sizes" property value, as it is assumed that it only requires one memory controller and no extension. So the optional use of "brcm,scb-sizes" will be backwards compatible.

One last layer of complexity exists: all of the viewports sizes must be added and rounded up to a power of two to determine what the "BAR" size is. Further, an offset must be given that indicates the base PCIe address of this "BAR". The use of the term BAR is typically associated with endpoint devices, and the term is used here because the PCIe HW may be used as an RC or an EP. In the former case, all of the system memory appears in a single "BAR" region in PCIe memory. As it turns out, BrcmSTB PCIe HW is rarely used in the EP role and its system of mapping memory is an artifact that requires multiple dma-ranges regions.

---
 drivers/pci/controller/pcie-brcmstb.c | 68 ++++++++++++++++++++-------
 1 file changed, 50 insertions(+), 18 deletions(-)
drivers/pci/controller/pcie-brcmstb.c +12 -12
index 8dacb9d3b7b6..3ef2d37cc43b 100644
@@ -715,22 +720,44 @@ static inline int brcm_pcie_get_rc_bar2_size_and_offset(struct brcm_pcie *pcie,
 							u64 *rc_bar2_offset)
 {
 	struct pci_host_bridge *bridge = pci_host_bridge_from_priv(pcie);
-	struct device *dev = pcie->dev;
 	struct resource_entry *entry;
+	struct device *dev = pcie->dev;
+	u64 lowest_pcie_addr = ~(u64)0;
+	int ret, i = 0;
+	u64 size = 0;
 
-	entry = resource_list_first_type(&bridge->dma_ranges, IORESOURCE_MEM);
-	if (!entry)
-		return -ENODEV;
+	resource_list_for_each_entry(entry, &bridge->dma_ranges) {
+		u64 pcie_beg = entry->res->start - entry->offset;
 
+		size += entry->res->end - entry->res->start + 1;
+		if (pcie_beg < lowest_pcie_addr)
+			lowest_pcie_addr = pcie_beg;
+	}
 
-	/*
-	 * The controller expects the inbound window offset to be calculated as
-	 * the difference between PCIe's address space and CPU's. The offset
-	 * provided by the firmware is calculated the opposite way, so we
-	 * negate it.
-	 */
-	*rc_bar2_offset = -entry->offset;
-	*rc_bar2_size = 1ULL << fls64(entry->res->end - entry->res->start);
+	if (lowest_pcie_addr == ~(u64)0) {
+		dev_err(dev, "DT node has no dma-ranges\n");

drivers/pci/controller/pcie-brcmstb.c static inline int brcm_pcie_get_rc_bar2_size_and_offset(struct brcm_pcie *pcie, · line 748

Quoted 10 lines
drivers/pci/controller/pcie-brcmstb.c +10 -0
+		return -EINVAL;
+	}
+
+	ret = of_property_read_variable_u64_array(pcie->np, "brcm,scb-sizes", pcie->memc_size, 1,
+						  PCIE_BRCM_MAX_MEMC);
+
+	if (ret <= 0) {
+		/* Make an educated guess */
+		pcie->num_memc = 1;
+		pcie->memc_size[0] = 1 << fls64(size - 1);

You need to 1ULL here.

Regards,
Nicolas

Quoted 15 lines
drivers/pci/controller/pcie-brcmstb.c +12 -0
+	} else {
+		pcie->num_memc = ret;
+	}
+
+	/* Each memc is viewed through a "port" that is a power of 2 */
+	for (i = 0, size = 0; i < pcie->num_memc; i++)
+		size += pcie->memc_size[i];
+
+	/* System memory starts at this address in PCIe-space */
+	*rc_bar2_offset = lowest_pcie_addr;
+	/* The sum of all memc views must also be a power of 2 */
+	*rc_bar2_size = 1ULL << fls64(size - 1);
 
 	/*
 	 * We validate the inbound memory view even though we should trust
#29 lore raw

Re: [PATCH v9 09/12] PCI: brcmstb: Set additional internal memory DMA viewport sizes

fls64

Quoted 103 lines · Nicolas Saenz Julienne

Hi Jim,

Quoted 99 lines · Jim Quinlan

The Raspberry Pi (RPI) is currently the only chip using this driver (pcie-brcmstb.c). There, only one memory controller is used, without an extension region, and the SCB0 viewport size is set to the size of the first and only dma-range region. Other BrcmSTB SOCs have more complicated memory configurations that require setting additional viewport sizes.

BrcmSTB PCIe controllers are intimately connected to the memory controller(s) on the SOC. The SOC may have one to three memory controllers; they are indicated by the term SCBi. Each controller has a base region and an optional extension region. In physical memory, the base and extension regions of a controller are not adjacent, but in PCIe-space they are.

There is a "viewport" for each memory controller that allows DMA from endpoint devices. Each viewport's size must be set to a power of two, and that size must be equal to or larger than the amount of memory each controller supports which is the sum of base region and its optional extension. Further, the 1-3 viewports are also adjacent in PCIe-space.

Unfortunately the viewport sizes cannot be ascertained from the "dma-ranges" property so they have their own property, "brcm,scb-sizes". This is because dma-range information does not indicate what memory controller it is associated. For example, consider the following case where the size of one dma-range is 2GB and the second dma-range is 1GB:

/* Case 1: SCB0 size set to 4GB */
dma-range0: 2GB (from memc0-base)
dma-range1: 1GB (from memc0-extension)

/* Case 2: SCB0 size set to 2GB, SCB1 size set to 1GB */
dma-range0: 2GB (from memc0-base)
dma-range1: 1GB (from memc0-extension)

By just looking at the dma-ranges information, one cannot tell which situation applies. That is why an additional property is needed. Its length indicates the number of memory controllers being used and each value indicates the viewport size.

Note that the RPI DT does not have a "brcm,scb-sizes" property value, as it is assumed that it only requires one memory controller and no extension. So the optional use of "brcm,scb-sizes" will be backwards compatible.

One last layer of complexity exists: all of the viewports sizes must be added and rounded up to a power of two to determine what the "BAR" size is. Further, an offset must be given that indicates the base PCIe address of this "BAR". The use of the term BAR is typically associated with endpoint devices, and the term is used here because the PCIe HW may be used as an RC or an EP. In the former case, all of the system memory appears in a single "BAR" region in PCIe memory. As it turns out, BrcmSTB PCIe HW is rarely used in the EP role and its system of mapping memory is an artifact that requires multiple dma-ranges regions.

---
 drivers/pci/controller/pcie-brcmstb.c | 68 ++++++++++++++++++++-------
 1 file changed, 50 insertions(+), 18 deletions(-)
drivers/pci/controller/pcie-brcmstb.c +16 -12
index 8dacb9d3b7b6..3ef2d37cc43b 100644
@@ -715,22 +720,44 @@ static inline int brcm_pcie_get_rc_bar2_size_and_offset(struct brcm_pcie *pcie,
                                                      u64 *rc_bar2_offset)
 {
      struct pci_host_bridge *bridge = pci_host_bridge_from_priv(pcie);
-     struct device *dev = pcie->dev;
      struct resource_entry *entry;
+     struct device *dev = pcie->dev;
+     u64 lowest_pcie_addr = ~(u64)0;
+     int ret, i = 0;
+     u64 size = 0;
 
-     entry = resource_list_first_type(&bridge->dma_ranges, IORESOURCE_MEM);
-     if (!entry)
-             return -ENODEV;
+     resource_list_for_each_entry(entry, &bridge->dma_ranges) {
+             u64 pcie_beg = entry->res->start - entry->offset;
 
+             size += entry->res->end - entry->res->start + 1;
+             if (pcie_beg < lowest_pcie_addr)
+                     lowest_pcie_addr = pcie_beg;
+     }
 
-     /*
-      * The controller expects the inbound window offset to be calculated as
-      * the difference between PCIe's address space and CPU's. The offset
-      * provided by the firmware is calculated the opposite way, so we
-      * negate it.
-      */
-     *rc_bar2_offset = -entry->offset;
-     *rc_bar2_size = 1ULL << fls64(entry->res->end - entry->res->start);
+     if (lowest_pcie_addr == ~(u64)0) {
+             dev_err(dev, "DT node has no dma-ranges\n");
+             return -EINVAL;
+     }
+
+     ret = of_property_read_variable_u64_array(pcie->np, "brcm,scb-sizes", pcie->memc_size, 1,
Quoted 8 lines

drivers/pci/controller/pcie-brcmstb.c static inline int brcm_pcie_get_rc_bar2_size_and_offset(struct brcm_pcie *pcie, · line 748

Quoted 6 lines
drivers/pci/controller/pcie-brcmstb.c +6 -0
+                                               PCIE_BRCM_MAX_MEMC);
+
+     if (ret <= 0) {
+             /* Make an educated guess */
+             pcie->num_memc = 1;
+             pcie->memc_size[0] = 1 << fls64(size - 1);

You need to 1ULL here.

Got it.
Thanks,
Jim

Quoted 20 lines

Regards,
Nicolas

Quoted 15 lines
drivers/pci/controller/pcie-brcmstb.c +12 -0
+     } else {
+             pcie->num_memc = ret;
+     }
+
+     /* Each memc is viewed through a "port" that is a power of 2 */
+     for (i = 0, size = 0; i < pcie->num_memc; i++)
+             size += pcie->memc_size[i];
+
+     /* System memory starts at this address in PCIe-space */
+     *rc_bar2_offset = lowest_pcie_addr;
+     /* The sum of all memc views must also be a power of 2 */
+     *rc_bar2_size = 1ULL << fls64(size - 1);
 
      /*
       * We validate the inbound memory view even though we should trust
#26 lore raw

Re: [PATCH v9 08/12] device core: Introduce DMA range map, supplanting dma_pfn_offset

In reply to Nicolas Saenz Julienne
Quoted 134 lines · Nicolas Saenz Julienne

Hi Jim, here's some comments after testing your series against RPi4.

Quoted 19 lines · Jim Quinlan

The new field 'dma_range_map' in struct device is used to facilitate the use of single or multiple offsets between mapping regions of cpu addrs and dma addrs. It subsumes the role of "dev->dma_pfn_offset" which was only capable of holding a single uniform offset and had no region bounds checking.

The function of_dma_get_range() has been modified so that it takes a single argument -- the device node -- and returns a map, NULL, or an error code. The map is an array that holds the information regarding the DMA regions. Each range entry contains the address offset, the cpu_start address, the dma_start address, and the size of the region.

of_dma_configure() is the typical manner to set range offsets but there are a number of ad hoc assignments to "dev->dma_pfn_offset" in the kernel driver code. These cases now invoke the function dma_attach_offset_range(dev, cpu_addr, dma_addr, size).

---

[...]

Quoted 95 lines
drivers/of/address.c +29 -32
index 8eea3f6e29a4..4b718d199efe 100644
@@ -918,33 +918,33 @@ void __iomem *of_io_request_and_map(struct device_node *np, int index,
 }
 EXPORT_SYMBOL(of_io_request_and_map);
 
+#ifdef CONFIG_HAS_DMA
 /**
- * of_dma_get_range - Get DMA range info
+ * of_dma_get_range - Get DMA range info and put it into a map array
  * @np:              device node to get DMA range info
- * @dma_addr:        pointer to store initial DMA address of DMA range
- * @paddr:   pointer to store initial CPU address of DMA range
- * @size:    pointer to store size of DMA range
+ * @map:     dma range structure to return
  *
  * Look in bottom up direction for the first "dma-ranges" property
- * and parse it.
- *  dma-ranges format:
+ * and parse it.  Put the information into a DMA offset map array.
+ *
+ * dma-ranges format:
  *   DMA addr (dma_addr)     : naddr cells
  *   CPU addr (phys_addr_t)  : pna cells
  *   size                    : nsize cells
  *
- * It returns -ENODEV if "dma-ranges" property was not found
- * for this device in DT.
+ * It returns -ENODEV if "dma-ranges" property was not found for this
+ * device in the DT.
  */
-int of_dma_get_range(struct device_node *np, u64 *dma_addr, u64 *paddr, u64 *size)
+int of_dma_get_range(struct device_node *np, const struct bus_dma_region **map)
 {
      struct device_node *node = of_node_get(np);
      const __be32 *ranges = NULL;
-     int len;
-     int ret = 0;
      bool found_dma_ranges = false;
      struct of_range_parser parser;
      struct of_range range;
-     u64 dma_start = U64_MAX, dma_end = 0, dma_offset = 0;
+     struct bus_dma_region *r;
+     int len, num_ranges = 0;
+     int ret;
 
      while (node) {
              ranges = of_get_property(node, "dma-ranges", &len);
@@ -970,44 +970,35 @@ int of_dma_get_range(struct device_node *np, u64 *dma_addr, u64 *paddr, u64 *siz
      }
 
      of_dma_range_parser_init(&parser, node);
+     for_each_of_range(&parser, &range)
+             num_ranges++;
+
+     of_dma_range_parser_init(&parser, node);
+
+     ret = -ENOMEM;
+     r = kcalloc(num_ranges + 1, sizeof(*r), GFP_KERNEL);
+     if (!r)
+             goto out;
 
+     /*
+      * Record all info in the generic DMA ranges array for struct device.
+      */
+     *map = r;
      for_each_of_range(&parser, &range) {
              pr_debug("dma_addr(%llx) cpu_addr(%llx) size(%llx)\n",
                       range.bus_addr, range.cpu_addr, range.size);
-
-             if (dma_offset && range.cpu_addr - range.bus_addr != dma_offset) {
-                     pr_warn("Can't handle multiple dma-ranges with different offsets on node(%pOF)\n", node);
-                     /* Don't error out as we'd break some existing DTs */
-                     continue;
-             }
-             dma_offset = range.cpu_addr - range.bus_addr;
-
-             /* Take lower and upper limits */
-             if (range.bus_addr < dma_start)
-                     dma_start = range.bus_addr;
-             if (range.bus_addr + range.size > dma_end)
-                     dma_end = range.bus_addr + range.size;
-     }
-
-     if (dma_start >= dma_end) {
-             ret = -EINVAL;
-             pr_debug("Invalid DMA ranges configuration on node(%pOF)\n",
-                      node);
-             goto out;
+             r->cpu_start = range.cpu_addr;
+             r->dma_start = range.bus_addr;
+             r->size = range.size;
+             r->offset = (u64)range.cpu_addr - (u64)range.bus_addr;

drivers/of/address.c int of_dma_get_range(struct device_node *np, u64 *dma_addr, u64 *paddr, u64 *siz · line 1005

Quoted 10 lines
drivers/of/address.c +1 -7
+             r++;
      }
 
-     *dma_addr = dma_start;
-     *size = dma_end - dma_start;
-     *paddr = dma_start + dma_offset;
-
-     pr_debug("final: dma_addr(%llx) cpu_addr(%llx) size(%llx)\n",
-              *dma_addr, *paddr, *size);
-

I think you're missing here:

Quoted 1 line
        ret = 0;

Yes. It somehow passed my tests because it still sets dev->dma_range_map.

Thanks again,
Jiom

Quoted 10 lines

drivers/of/address.c int of_dma_get_range(struct device_node *np, u64 *dma_addr, u64 *paddr, u64 *siz · line 1000

Quoted 6 lines
drivers/of/address.c +0 -1
 out:
      of_node_put(node);
-
      return ret;
 }

Regards,
Nicolas

_______________________________________________
iommu mailing list
[email protected]
https://lists.linuxfoundation.org/mailman/listinfo/iommu