tty/synclink: remove leftover bits of non-PCI card support
PATCH 1/1 tty/synclink: remove leftover bits of non-PCI card support
Since commit 1355cba9c3ba ("tty/synclink: remove ISA support"), the synlink driver only supports PCI card. Remove any leftover dead code to support other cards.
--- drivers/tty/synclink.c | 350 +++++++++++++---------------------------- 1 file changed, 109 insertions(+), 241 deletions(-)
drivers/tty/synclink.c +109 -241
@@ -252,7 +252,6 @@ struct mgsl_struct {char device_name[25 ];/* device instance name */ -unsigned int bus_type;/* expansion bus type (ISA,EISA,PCI) */ unsigned char bus;/* expansion bus number (zero based) */ unsigned char function;/* PCI device number */
@@ -3432,15 +3431,9 @@ static inline void line_info(struct seq_file *m, struct mgsl_struct *info)char stat_buf[30 ];unsigned long flags; -if (info->bus_type ==MGSL_BUS_TYPE_PCI ) { -seq_printf (m,"%s:PCI io:%04X irq:%d mem:%08X lcr:%08X" , - info->device_name, info->io_base, info->irq_level, - info->phys_memory_base, info->phys_lcr_base); - }else { -seq_printf (m,"%s:(E)ISA io:%04X irq:%d dma:%d" , - info->device_name, info->io_base, - info->irq_level, info->dma_level); - } +seq_printf (m,"%s:PCI io:%04X irq:%d mem:%08X lcr:%08X" , + info->device_name, info->io_base, info->irq_level, + info->phys_memory_base, info->phys_lcr_base);/* output current serial signal states */ spin_lock_irqsave (&info->irq_spinlock,flags);
@@ -3556,54 +3549,27 @@ static int mgsl_allocate_dma_buffers(struct mgsl_struct *info)if ( info->max_frame_size %DMABUFFERSIZE ) BuffersPerFrame++; -if ( info->bus_type ==MGSL_BUS_TYPE_PCI ) { -/* -* The PCI adapter has 256KBytes of shared memory to use. -* This is 64 PAGE_SIZE buffers. -* -* The first page is used for padding at this time so the -* buffer list does not begin at offset 0 of the PCI -* adapter's shared memory. -* -* The 2nd page is used for the buffer list. A 4K buffer -* list can hold 128 DMA_BUFFER structures at 32 bytes -* each. -* -* This leaves 62 4K pages. -* -* The next N pages are used for transmit frame(s). We -* reserve enough 4K page blocks to hold the required -* number of transmit dma buffers (num_tx_dma_buffers), -* each of MaxFrameSize size. -* -* Of the remaining pages (62-N), determine how many can -* be used to receive full MaxFrameSize inbound frames -*/ - info->tx_buffer_count = info->num_tx_dma_buffers * BuffersPerFrame; - info->rx_buffer_count =62 - info->tx_buffer_count; - }else { -/* Calculate the number of PAGE_SIZE buffers needed for */ -/* receive and transmit DMA buffers. */ - - -/* Calculate the number of DMA buffers necessary to */ -/* hold 7 max size receive frames and one max size transmit frame. */ -/* The receive buffer count is bumped by one so we avoid an */ -/* End of List condition if all receive buffers are used when */ -/* using linked list DMA buffers. */ - - info->tx_buffer_count = info->num_tx_dma_buffers * BuffersPerFrame; - info->rx_buffer_count = (BuffersPerFrame *MAXRXFRAMES ) +6 ; - -/* -* limit total TxBuffers & RxBuffers to 62 4K total -* (ala PCI Allocation) -*/ - -if ( (info->tx_buffer_count + info->rx_buffer_count) >62 ) - info->rx_buffer_count =62 - info->tx_buffer_count; - - } +/* +* The PCI adapter has 256KBytes of shared memory to use. This is 64 +* PAGE_SIZE buffers. +* +* The first page is used for padding at this time so the buffer list +* does not begin at offset 0 of the PCI adapter's shared memory. +* +* The 2nd page is used for the buffer list. A 4K buffer list can hold +* 128 DMA_BUFFER structures at 32 bytes each. +* +* This leaves 62 4K pages. +* +* The next N pages are used for transmit frame(s). We reserve enough +* 4K page blocks to hold the required number of transmit dma buffers +* (num_tx_dma_buffers), each of MaxFrameSize size. +* +* Of the remaining pages (62-N), determine how many can be used to +* receive full MaxFrameSize inbound frames +*/ + info->tx_buffer_count = info->num_tx_dma_buffers * BuffersPerFrame; + info->rx_buffer_count =62 - info->tx_buffer_count;if ( debug_level >=DEBUG_LEVEL_INFO ) printk("%s(%d):Allocating %d TX and %d RX DMA buffers.\n",
@@ -3652,23 +3618,10 @@ static int mgsl_alloc_buffer_list_memory( struct mgsl_struct *info ) {unsigned int i; -if ( info->bus_type ==MGSL_BUS_TYPE_PCI ) { -/* PCI adapter uses shared memory. */ - info->buffer_list = info->memory_base + info->last_mem_alloc; - info->buffer_list_phys = info->last_mem_alloc; - info->last_mem_alloc +=BUFFERLISTSIZE ; - }else { -/* ISA adapter uses system memory. */ -/* The buffer lists are allocated as a common buffer that both */ -/* the processor and adapter can access. This allows the driver to */ -/* inspect portions of the buffer while other portions are being */ -/* updated by the adapter using Bus Master DMA. */ - - info->buffer_list =dma_alloc_coherent (NULL ,BUFFERLISTSIZE , &info->buffer_list_dma_addr,GFP_KERNEL ); -if (info->buffer_list ==NULL ) -return -ENOMEM ; - info->buffer_list_phys = (u32)(info->buffer_list_dma_addr); - } +/* PCI adapter uses shared memory. */ + info->buffer_list = info->memory_base + info->last_mem_alloc; + info->buffer_list_phys = info->last_mem_alloc; + info->last_mem_alloc +=BUFFERLISTSIZE ;/* We got the memory for the buffer entry lists. */ /* Initialize the memory block to all zeros. */
@@ -3734,9 +3687,6 @@ static int mgsl_alloc_buffer_list_memory( struct mgsl_struct *info )*/ static void mgsl_free_buffer_list_memory (struct mgsl_struct *info ) { -if (info->buffer_list && info->bus_type !=MGSL_BUS_TYPE_PCI ) -dma_free_coherent (NULL ,BUFFERLISTSIZE , info->buffer_list, info->buffer_list_dma_addr); - info->buffer_list =NULL ; info->rx_buffer_list =NULL ; info->tx_buffer_list =NULL ;
@@ -3762,24 +3712,13 @@ static void mgsl_free_buffer_list_memory( struct mgsl_struct *info )static int mgsl_alloc_frame_memory (struct mgsl_struct *info,DMABUFFERENTRY *BufferList,int Buffercount) {int i; -u32 phys_addr;/* Allocate page sized buffers for the receive buffer list */ for ( i =0 ; i < Buffercount; i++ ) { -if ( info->bus_type ==MGSL_BUS_TYPE_PCI ) { -/* PCI adapter uses shared memory buffers. */ - BufferList[i].virt_addr = info->memory_base + info->last_mem_alloc; - phys_addr = info->last_mem_alloc; - info->last_mem_alloc +=DMABUFFERSIZE ; - }else { -/* ISA adapter uses system memory. */ - BufferList[i].virt_addr =dma_alloc_coherent (NULL ,DMABUFFERSIZE , &BufferList[i].dma_addr,GFP_KERNEL ); -if (BufferList[i].virt_addr ==NULL ) -return -ENOMEM ; - phys_addr = (u32)(BufferList[i].dma_addr); - } - BufferList[i].phys_addr = phys_addr; + BufferList[i].virt_addr = info->memory_base + info->last_mem_alloc; + BufferList[i].phys_addr = info->last_mem_alloc; + info->last_mem_alloc +=DMABUFFERSIZE ; }return 0 ;
@@ -3807,8 +3746,6 @@ static void mgsl_free_frame_memory(struct mgsl_struct *info, DMABUFFERENTRY *Bufif ( BufferList ) {for ( i =0 ; i < Buffercount ; i++ ) {if ( BufferList[i].virt_addr ) { -if ( info->bus_type !=MGSL_BUS_TYPE_PCI ) -dma_free_coherent (NULL ,DMABUFFERSIZE , BufferList[i].virt_addr, BufferList[i].dma_addr); BufferList[i].virt_addr =NULL ; } }
@@ -4040,58 +3977,40 @@ static int mgsl_claim_resources(struct mgsl_struct *info) } info->irq_requested = true; -if ( info->bus_type ==MGSL_BUS_TYPE_PCI ) { -if (request_mem_region (info->phys_memory_base,0x40000 ,"synclink" ) ==NULL ) { -printk ("%s(%d):mem addr conflict device %s Addr=%08X\n" , - __FILE__,__LINE__,info->device_name, info->phys_memory_base); - goto errout; - } - info->shared_mem_requested = true; -if (request_mem_region (info->phys_lcr_base + info->lcr_offset,128 ,"synclink" ) ==NULL ) { -printk ("%s(%d):lcr mem addr conflict device %s Addr=%08X\n" , - __FILE__,__LINE__,info->device_name, info->phys_lcr_base + info->lcr_offset); - goto errout; - } - info->lcr_mem_requested = true; - - info->memory_base =ioremap (info->phys_memory_base, -0x40000 ); -if (!info->memory_base) { -printk ("%s(%d):Can't map shared memory on device %s MemAddr=%08X\n" , - __FILE__,__LINE__,info->device_name, info->phys_memory_base ); - goto errout; - } - -if ( !mgsl_memory_test (info) ) { -printk ("%s(%d):Failed shared memory test %s MemAddr=%08X\n" , - __FILE__,__LINE__,info->device_name, info->phys_memory_base ); - goto errout; - } - - info->lcr_base =ioremap (info->phys_lcr_base, -PAGE_SIZE ); -if (!info->lcr_base) { -printk ("%s(%d):Can't map LCR memory on device %s MemAddr=%08X\n" , - __FILE__,__LINE__,info->device_name, info->phys_lcr_base ); - goto errout; - } - info->lcr_base += info->lcr_offset; +if (request_mem_region (info->phys_memory_base,0x40000 ,"synclink" ) ==NULL ) { +printk ("%s(%d):mem addr conflict device %s Addr=%08X\n" , + __FILE__,__LINE__,info->device_name, info->phys_memory_base); + goto errout; + } + info->shared_mem_requested = true; +if (request_mem_region (info->phys_lcr_base + info->lcr_offset,128 ,"synclink" ) ==NULL ) { +printk ("%s(%d):lcr mem addr conflict device %s Addr=%08X\n" , + __FILE__,__LINE__,info->device_name, info->phys_lcr_base + info->lcr_offset); + goto errout; + } + info->lcr_mem_requested = true; + + info->memory_base =ioremap (info->phys_memory_base,0x40000 ); +if (!info->memory_base) { +printk ("%s(%d):Can't map shared memory on device %s MemAddr=%08X\n" , + __FILE__,__LINE__,info->device_name, info->phys_memory_base ); + goto errout; + } - }else { -/* claim DMA channel */ +if ( !mgsl_memory_test (info) ) { +printk ("%s(%d):Failed shared memory test %s MemAddr=%08X\n" , + __FILE__,__LINE__,info->device_name, info->phys_memory_base ); + goto errout; + } -if (request_dma (info->dma_level,info->device_name) <0 ){ -printk ("%s(%d):Can't request DMA channel on device %s DMA=%d\n" , - __FILE__,__LINE__,info->device_name, info->dma_level ); - goto errout; - } - info->dma_requested = true; - -/* ISA adapter uses bus master DMA */ -set_dma_mode (info->dma_level,DMA_MODE_CASCADE ); -enable_dma (info->dma_level); + info->lcr_base =ioremap (info->phys_lcr_base,PAGE_SIZE ); +if (!info->lcr_base) { +printk ("%s(%d):Can't map LCR memory on device %s MemAddr=%08X\n" , + __FILE__,__LINE__,info->device_name, info->phys_lcr_base ); + goto errout; } - + info->lcr_base += info->lcr_offset; +if (mgsl_allocate_dma_buffers (info) <0 ) {printk ("%s(%d):Can't allocate DMA buffers on device %s DMA=%d\n" , __FILE__,__LINE__,info->device_name, info->dma_level );
@@ -4200,16 +4119,10 @@ static void mgsl_add_device( struct mgsl_struct *info )else if ( info->max_frame_size >65535 ) info->max_frame_size =65535 ; -if ( info->bus_type ==MGSL_BUS_TYPE_PCI ) { -printk ("SyncLink PCI v%d %s: IO=%04X IRQ=%d Mem=%08X,%08X MaxFrameSize=%u\n" , - info->hw_version +1 , info->device_name, info->io_base, info->irq_level, - info->phys_memory_base, info->phys_lcr_base, - info->max_frame_size ); - }else { -printk ("SyncLink ISA %s: IO=%04X IRQ=%d DMA=%d MaxFrameSize=%u\n" , - info->device_name, info->io_base, info->irq_level, info->dma_level, - info->max_frame_size ); - } +printk ("SyncLink PCI v%d %s: IO=%04X IRQ=%d Mem=%08X,%08X MaxFrameSize=%u\n" , + info->hw_version +1 , info->device_name, info->io_base, info->irq_level, + info->phys_memory_base, info->phys_lcr_base, + info->max_frame_size );#if SYNCLINK_GENERIC_HDLC hdlcdev_init (info);
@@ -4420,8 +4333,7 @@ static void usc_RTCmd( struct mgsl_struct *info, u16 Cmd )outw ( Cmd + info->loopback_bits, info->io_base +CCAR );/* Read to flush write to CCAR */ -if ( info->bus_type ==MGSL_BUS_TYPE_PCI ) -inw ( info->io_base +CCAR ); +inw ( info->io_base +CCAR ); }/* end of usc_RTCmd() */
@@ -4445,8 +4357,7 @@ static void usc_DmaCmd( struct mgsl_struct *info, u16 Cmd )outw ( Cmd + info->mbre_bit, info->io_base );/* Read to flush write to DCAR */ -if ( info->bus_type ==MGSL_BUS_TYPE_PCI ) -inw ( info->io_base ); +inw ( info->io_base ); }/* end of usc_DmaCmd() */
@@ -4475,8 +4386,7 @@ static void usc_OutDmaReg( struct mgsl_struct *info, u16 RegAddr, u16 RegValue )outw ( RegValue, info->io_base );/* Read to flush write to DCAR */ -if ( info->bus_type ==MGSL_BUS_TYPE_PCI ) -inw ( info->io_base ); +inw ( info->io_base ); }/* end of usc_OutDmaReg() */
@@ -4528,8 +4438,7 @@ static void usc_OutReg( struct mgsl_struct *info, u16 RegAddr, u16 RegValue )outw ( RegValue, info->io_base +CCAR );/* Read to flush write to CCAR */ -if ( info->bus_type ==MGSL_BUS_TYPE_PCI ) -inw ( info->io_base +CCAR ); +inw ( info->io_base +CCAR ); }/* end of usc_OutReg() */
@@ -4728,10 +4637,7 @@ static void usc_set_sdlc_mode( struct mgsl_struct *info ) RegValue =usc_InReg ( info,RICR ) &0xc0 ; -if ( info->bus_type ==MGSL_BUS_TYPE_PCI ) -usc_OutReg ( info,RICR , (u16)(0x030a | RegValue) ); -else -usc_OutReg ( info,RICR , (u16)(0x140a | RegValue) ); +usc_OutReg ( info,RICR , (u16)(0x030a | RegValue) );/* Unlatch all Rx status bits and clear Rx status IRQ Pending */
@@ -4792,10 +4698,7 @@ static void usc_set_sdlc_mode( struct mgsl_struct *info )* 0000 0000 0011 0110 = 0x0036 */ -if ( info->bus_type ==MGSL_BUS_TYPE_PCI ) -usc_OutReg ( info,TICR ,0x0736 ); -else -usc_OutReg ( info,TICR ,0x1436 ); +usc_OutReg ( info,TICR ,0x0736 );usc_UnlatchTxstatusBits ( info,TXSTATUS_ALL );usc_ClearIrqPendingBits ( info,TRANSMIT_STATUS );
@@ -4885,10 +4788,7 @@ static void usc_set_sdlc_mode( struct mgsl_struct *info )/* DPLL is enabled. Use BRG1 to provide continuous reference clock */ /* for DPLL. DPLL mode in HCR is dependent on the encoding used. */ -if ( info->bus_type ==MGSL_BUS_TYPE_PCI ) - XtalSpeed =11059200 ; -else - XtalSpeed =14745600 ; + XtalSpeed =11059200 ;if ( info->params.flags &HDLC_FLAG_DPLL_DIV16 ) { DpllDivisor =16 ;
@@ -5011,13 +4911,8 @@ static void usc_set_sdlc_mode( struct mgsl_struct *info )* 0110 0000 0000 1011 = 0x600b */ -if ( info->bus_type ==MGSL_BUS_TYPE_PCI ) { -/* PCI adapter does not need DMA wait state */ -usc_OutDmaReg ( info,DCR ,0xa00b ); - } -else -usc_OutDmaReg ( info,DCR ,0x800b ); - +/* PCI adapter does not need DMA wait state */ +usc_OutDmaReg ( info,DCR ,0xa00b );/* Receive DMA mode Register (RDMR) *
@@ -5109,12 +5004,8 @@ static void usc_set_sdlc_mode( struct mgsl_struct *info )* <7..0> 0x00 Maximum number of clock cycles per bus grant */ -if ( info->bus_type ==MGSL_BUS_TYPE_PCI ) { -/* don't limit bus occupancy on PCI adapter */ -usc_OutDmaReg ( info,BDCR ,0x0000 ); - } -else -usc_OutDmaReg ( info,BDCR ,0x2000 ); +/* don't limit bus occupancy on PCI adapter */ +usc_OutDmaReg ( info,BDCR ,0x0000 );usc_stop_transmitter (info);usc_stop_receiver (info);
@@ -5155,10 +5046,7 @@ static void usc_enable_loopback(struct mgsl_struct *info, int enable)/* Write 16-bit Time Constant for BRG0 */ /* use clock speed if available, otherwise use 8 for diagnostics */ if (info->params.clock_speed) { -if (info->bus_type ==MGSL_BUS_TYPE_PCI ) -usc_OutReg (info,TC0R , (u16)((11059200 /info->params.clock_speed)-1 )); -else -usc_OutReg (info,TC0R , (u16)((14745600 /info->params.clock_speed)-1 )); +usc_OutReg (info,TC0R , (u16)((11059200 /info->params.clock_speed)-1 )); }else usc_OutReg (info,TC0R , (u16 )8 );
@@ -5201,10 +5089,7 @@ static void usc_enable_aux_clock( struct mgsl_struct *info, u32 data_rate )u16 Tc;if ( data_rate ) { -if ( info->bus_type ==MGSL_BUS_TYPE_PCI ) - XtalSpeed =11059200 ; -else - XtalSpeed =14745600 ; + XtalSpeed =11059200 ;/* Tc = (Xtal/Speed) - 1 */
@@ -5682,44 +5567,38 @@ static void usc_load_txfifo( struct mgsl_struct *info )*/ static void usc_reset (struct mgsl_struct *info ) { -if ( info->bus_type ==MGSL_BUS_TYPE_PCI ) { -int i; -u32 readval; +int i; +u32 readval; -/* Set BIT30 of Misc Control Register */ -/* (Local Control Register 0x50) to force reset of USC. */ +/* Set BIT30 of Misc Control Register */ +/* (Local Control Register 0x50) to force reset of USC. */ -volatile u32 *MiscCtrl = (u32 *)(info->lcr_base +0x50 ); -u32 *LCR0BRDR = (u32 *)(info->lcr_base +0x28 ); +volatile u32 *MiscCtrl = (u32 *)(info->lcr_base +0x50 ); +u32 *LCR0BRDR = (u32 *)(info->lcr_base +0x28 ); - info->misc_ctrl_value |=BIT30 ; - *MiscCtrl = info->misc_ctrl_value; + info->misc_ctrl_value |=BIT30 ; + *MiscCtrl = info->misc_ctrl_value; -/* -* Force at least 170ns delay before clearing -* reset bit. Each read from LCR takes at least -* 30ns so 10 times for 300ns to be safe. -*/ -for (i=0 ;i<10 ;i++) - readval = *MiscCtrl; - - info->misc_ctrl_value &= ~BIT30 ; - *MiscCtrl = info->misc_ctrl_value; - - *LCR0BRDR =BUS_DESCRIPTOR ( -1 ,// Write Strobe Hold (0-3) -2 ,// Write Strobe Delay (0-3) -2 ,// Read Strobe Delay (0-3) -0 ,// NWDD (Write data-data) (0-3) -4 ,// NWAD (Write Addr-data) (0-31) -0 ,// NXDA (Read/Write Data-Addr) (0-3) -0 ,// NRDD (Read Data-Data) (0-3) -5 // NRAD (Read Addr-Data) (0-31) - ); - }else { -/* do HW reset */ -outb (0 ,info->io_base +8 ); - } +/* +* Force at least 170ns delay before clearing reset bit. Each read from +* LCR takes at least 30ns so 10 times for 300ns to be safe. +*/ +for (i=0 ;i<10 ;i++) + readval = *MiscCtrl; + + info->misc_ctrl_value &= ~BIT30 ; + *MiscCtrl = info->misc_ctrl_value; + + *LCR0BRDR =BUS_DESCRIPTOR ( +1 ,// Write Strobe Hold (0-3) +2 ,// Write Strobe Delay (0-3) +2 ,// Read Strobe Delay (0-3) +0 ,// NWDD (Write data-data) (0-3) +4 ,// NWAD (Write Addr-data) (0-31) +0 ,// NXDA (Read/Write Data-Addr) (0-3) +0 ,// NRDD (Read Data-Data) (0-3) +5 // NRAD (Read Addr-Data) (0-31) + ); info->mbre_bit =0 ; info->loopback_bits =0 ;
@@ -6228,11 +6107,7 @@ static void usc_enable_async_clock( struct mgsl_struct *info, u32 data_rate )* ClkSpeed = 921600 (ISA), 691200 (PCI) */ -if ( info->bus_type ==MGSL_BUS_TYPE_PCI ) -usc_OutReg ( info,TC0R , (u16)((691200 /data_rate) -1 ) ); -else -usc_OutReg ( info,TC0R , (u16)((921600 /data_rate) -1 ) ); - +usc_OutReg ( info,TC0R , (u16)((691200 /data_rate) -1 ) );/* * Hardware Configuration Register (HCR)
@@ -6837,10 +6712,7 @@ static void mgsl_load_tx_dma_buffer(struct mgsl_struct *info,/* Actually copy data from source buffer to DMA buffer. */ /* Also set the data count for this individual DMA buffer. */ -if ( info->bus_type ==MGSL_BUS_TYPE_PCI ) -mgsl_load_pci_memory (pBufEntry->virt_addr, Buffer,Copycount); -else -memcpy (pBufEntry->virt_addr, Buffer, Copycount); +mgsl_load_pci_memory (pBufEntry->virt_addr, Buffer,Copycount); pBufEntry->count = Copycount;
@@ -7315,9 +7187,6 @@ static bool mgsl_memory_test( struct mgsl_struct *info )unsigned long TestLimit =SHARED_MEM_ADDRESS_SIZE /sizeof (unsigned long );unsigned long * TestAddr; -if ( info->bus_type !=MGSL_BUS_TYPE_PCI ) -return true; - TestAddr = (unsigned long *)info->memory_base;/* Test data lines with test pattern at one location. */
@@ -8003,7 +7872,6 @@ static int synclink_init_one (struct pci_dev *dev, info->lcr_offset = info->phys_lcr_base & (PAGE_SIZE -1 ); info->phys_lcr_base &= ~(PAGE_SIZE -1 ); - info->bus_type =MGSL_BUS_TYPE_PCI ; info->io_addr_size =8 ; info->irq_flags =IRQF_SHARED ;
Signature · 1 line
2.27.0
Jiri Slaby
maintainerQuoted 3 lines · Christoph Hellwig
Since commit
1355cba9c3ba("tty/synclink: remove ISA support"), the synlink driver only supports PCI card. Remove any leftover dead code to support other cards.
So now you can remove also the defines and bus_type completely:
$ git grep -E 'MGSL_BUS_TYPE_(E?ISA|PCI)' drivers/tty/synclink_gt.c: info->bus_type = MGSL_BUS_TYPE_PCI; drivers/tty/synclinkmp.c: info->bus_type = MGSL_BUS_TYPE_PCI; include/uapi/linux/synclink.h:#define MGSL_BUS_TYPE_ISA 1 include/uapi/linux/synclink.h:#define MGSL_BUS_TYPE_EISA 2 include/uapi/linux/synclink.h:#define MGSL_BUS_TYPE_PCI 5
$ git grep -w bus_type drivers/tty/synclink* drivers/tty/synclink_gt.c: unsigned int bus_type; drivers/tty/synclink_gt.c: info->bus_type = MGSL_BUS_TYPE_PCI; drivers/tty/synclinkmp.c: unsigned int bus_type; /* expansion bus type (ISA,EISA,PCI) */ drivers/tty/synclinkmp.c: info->bus_type = MGSL_BUS_TYPE_PCI;
Quoted 2 lines
drivers/tty/synclink.c +0
-0
...
Quoted 1 line
drivers/tty/synclink.c +0
-0@@ -4040,58 +3977,40 @@ static int mgsl_claim_resources(struct mgsl_struct *info)
...
Quoted 17 lines
drivers/tty/synclink.c +5
-11- }else { -/* claim DMA channel */ +if ( !mgsl_memory_test (info) ) { +printk ("%s(%d):Failed shared memory test %s MemAddr=%08X\n" , + __FILE__,__LINE__,info->device_name, info->phys_memory_base ); + goto errout; + } -if (request_dma (info->dma_level,info->device_name) <0 ){ -printk ("%s(%d):Can't request DMA channel on device %s DMA=%d\n" , - __FILE__,__LINE__,info->device_name, info->dma_level ); - goto errout; - } - info->dma_requested = true; - -/* ISA adapter uses bus master DMA */ -set_dma_mode (info->dma_level,DMA_MODE_CASCADE );
drivers/tty/synclink.c static int mgsl_claim_resources(struct mgsl_struct *info) · line 4013
Quoted 10 lines
drivers/tty/synclink.c +7
-2-enable_dma (info->dma_level); + info->lcr_base =ioremap (info->phys_lcr_base,PAGE_SIZE ); +if (!info->lcr_base) { +printk ("%s(%d):Can't map LCR memory on device %s MemAddr=%08X\n" , + __FILE__,__LINE__,info->device_name, info->phys_lcr_base ); + goto errout; } - + info->lcr_base += info->lcr_offset; +
Could you fix up the whitespace git show warns about (git show outputs red background, if you use colors). Like this one? It looks like you added one more \t on an empty line here.
Quoted 11 lines
drivers/tty/synclink.c +0
-4if (mgsl_allocate_dma_buffers (info) <0 ) {printk ("%s(%d):Can't allocate DMA buffers on device %s DMA=%d\n" , __FILE__,__LINE__,info->device_name, info->dma_level );@@ -4200,16 +4119,10 @@ static void mgsl_add_device( struct mgsl_struct *info )else if ( info->max_frame_size >65535 ) info->max_frame_size =65535 ; -if ( info->bus_type ==MGSL_BUS_TYPE_PCI ) { - printk( "SyncLink PCI v%d %s: IO=%04X IRQ=%d Mem=%08X,%08X MaxFrameSize=%u\n", - info->hw_version + 1, info->device_name, info->io_base, info->irq_level, - info->phys_memory_base, info->phys_lcr_base,
drivers/tty/synclink.c static void mgsl_add_device( struct mgsl_struct *info ) · line 4125
Quoted 10 lines
drivers/tty/synclink.c +4
-6- info->max_frame_size ); - }else { -printk ("SyncLink ISA %s: IO=%04X IRQ=%d DMA=%d MaxFrameSize=%u\n" , - info->device_name, info->io_base, info->irq_level, info->dma_level, - info->max_frame_size ); - } +printk ("SyncLink PCI v%d %s: IO=%04X IRQ=%d Mem=%08X,%08X MaxFrameSize=%u\n" , + info->hw_version +1 , info->device_name, info->io_base, info->irq_level, + info->phys_memory_base, info->phys_lcr_base, + info->max_frame_size );
Or here, there is \t, 4 spaces and \t again.
thanks,
Signature · 1 line
js
Jiri Slaby
maintainerQuoted 13 lines · Jiri Slaby
Quoted 3 lines · Christoph Hellwig
Since commit
1355cba9c3ba("tty/synclink: remove ISA support"), the synlink driver only supports PCI card. Remove any leftover dead code to support other cards.So now you can remove also the defines and
bus_typecompletely:$ git grep -E 'MGSL_BUS_TYPE_(E?ISA|PCI)' drivers/tty/synclink_gt.c: info->bus_type = MGSL_BUS_TYPE_PCI; drivers/tty/synclinkmp.c: info->bus_type = MGSL_BUS_TYPE_PCI; include/uapi/linux/synclink.h:#define MGSL_BUS_TYPE_ISA 1 include/uapi/linux/synclink.h:#define MGSL_BUS_TYPE_EISA 2 include/uapi/linux/synclink.h:#define MGSL_BUS_TYPE_PCI 5
Quoted 6 lines
$ git grep -w bus_type drivers/tty/synclink* drivers/tty/synclink_gt.c: unsigned int bus_type; drivers/tty/synclink_gt.c: info->bus_type = MGSL_BUS_TYPE_PCI; drivers/tty/synclinkmp.c: unsigned int bus_type; /* expansion bus type (ISA,EISA,PCI) */ drivers/tty/synclinkmp.c: info->bus_type = MGSL_BUS_TYPE_PCI;
And also MAX_ISA_DEVICES and MAX_PCI_DEVICES are (transitively) unused.
Signature · 1 line
js
Quoted 5 lines · Jiri Slaby
Quoted 3 lines · Christoph Hellwig
Since commit
1355cba9c3ba("tty/synclink: remove ISA support"), the synlink driver only supports PCI card. Remove any leftover dead code to support other cards.
Quoted 7 lines
So now you can remove also the defines and
bus_typecompletely:$ git grep -E 'MGSL_BUS_TYPE_(E?ISA|PCI)' drivers/tty/synclink_gt.c: info->bus_type = MGSL_BUS_TYPE_PCI; drivers/tty/synclinkmp.c: info->bus_type = MGSL_BUS_TYPE_PCI; include/uapi/linux/synclink.h:#define MGSL_BUS_TYPE_ISA 1 include/uapi/linux/synclink.h:#define MGSL_BUS_TYPE_EISA 2 include/uapi/linux/synclink.h:#define MGSL_BUS_TYPE_PCI 5
This is in a uapi header, so I didn't dare to touch it.
Quoted 7 lines
$ git grep -w bus_type drivers/tty/synclink* drivers/tty/synclink_gt.c: unsigned int bus_type; drivers/tty/synclink_gt.c: info->bus_type = MGSL_BUS_TYPE_PCI; drivers/tty/synclinkmp.c: unsigned int bus_type; /* expansion bus type (ISA,EISA,PCI) */ drivers/tty/synclinkmp.c: info->bus_type = MGSL_BUS_TYPE_PCI;
Despite the similar names these are actually two drivers entirely separate form the main synclink one.
Jiri Slaby
maintainerQuoted 14 lines · Christoph Hellwig
Quoted 5 lines · Jiri Slaby
Quoted 3 lines · Christoph Hellwig
Since commit
1355cba9c3ba("tty/synclink: remove ISA support"), the synlink driver only supports PCI card. Remove any leftover dead code to support other cards.Quoted 7 lines
So now you can remove also the defines and
bus_typecompletely:$ git grep -E 'MGSL_BUS_TYPE_(E?ISA|PCI)' drivers/tty/synclink_gt.c: info->bus_type = MGSL_BUS_TYPE_PCI; drivers/tty/synclinkmp.c: info->bus_type = MGSL_BUS_TYPE_PCI; include/uapi/linux/synclink.h:#define MGSL_BUS_TYPE_ISA 1 include/uapi/linux/synclink.h:#define MGSL_BUS_TYPE_EISA 2 include/uapi/linux/synclink.h:#define MGSL_BUS_TYPE_PCI 5
Quoted 1 line
This is in a uapi header, so I didn't dare to touch it.
Ah, sure. Then OK.
Just wondering, who would place this into a uapi header?
Quoted 9 lines
Quoted 6 lines
$ git grep -w bus_type drivers/tty/synclink* drivers/tty/synclink_gt.c: unsigned int bus_type; drivers/tty/synclink_gt.c: info->bus_type = MGSL_BUS_TYPE_PCI; drivers/tty/synclinkmp.c: unsigned int bus_type; /* expansion bus type (ISA,EISA,PCI) */ drivers/tty/synclinkmp.c: info->bus_type = MGSL_BUS_TYPE_PCI;Despite the similar names these are actually two drivers entirely separate form the main synclink one.
I know, but it's set-but-unused field in both of them. So if the defines went away, this could go too. But given the defines stay, it doesn't matter. All 3 drivers are old unmaintained crap anyway:
$ git log --oneline --no-merges drivers/tty/synclink*|wc -l 79
thanks,
Signature · 1 line
js
Greg KH
maintainerQuoted 15 lines · Jiri Slaby
Quoted 14 lines · Christoph Hellwig
Quoted 12 lines · Jiri Slaby
Quoted 3 lines · Christoph Hellwig
Since commit
1355cba9c3ba("tty/synclink: remove ISA support"), the synlink driver only supports PCI card. Remove any leftover dead code to support other cards.So now you can remove also the defines and
bus_typecompletely:$ git grep -E 'MGSL_BUS_TYPE_(E?ISA|PCI)' drivers/tty/synclink_gt.c: info->bus_type = MGSL_BUS_TYPE_PCI; drivers/tty/synclinkmp.c: info->bus_type = MGSL_BUS_TYPE_PCI; include/uapi/linux/synclink.h:#define MGSL_BUS_TYPE_ISA 1 include/uapi/linux/synclink.h:#define MGSL_BUS_TYPE_EISA 2 include/uapi/linux/synclink.h:#define MGSL_BUS_TYPE_PCI 5
Quoted 5 lines
Quoted 1 line
This is in a uapi header, so I didn't dare to touch it.
Ah, sure. Then OK.
Just wondering, who would place this into a uapi header?
People didn't realize they were uapi headers a long time ago, when everything was in the same directory/files :(
thanks,
greg k-h