Skip to contentSkip to conversation

add SATA/AHCI support for BananaPi R64

PATCH New Frank Wunderlich 3 participants 14 messages Aug 13, 2020 – Aug 20, 2020

Subsystems (7)
lore
Share & tools
lore
#0 lore raw

v3 cover add SATA/AHCI support for BananaPi R64

From: Frank Wunderlich <[email protected]>

BananaPi R64 has an SATA socket where an HDD can be connected. I have ported Linux Driver to Uboot and can access my harddrive

BPI-R64> scsi scan
scanning bus for devices...
Target spinup took 0 ms.
AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
flags: ncq stag pm clo only pmp pio slum part ccc apst
Device 0: (0:0) Vendor: ATA Prod.: ST750LM022 HN-M7 Rev: 2AR1
Type: Hard Disk
Capacity: 715404.8 MB = 698.6 GB (1465149168 x 512)
BPI-R64> ls scsi 0:1
EFI/
512 BOOTSECT.BAK

1 file(s), 1 dir(s)

BPI-R64>

this Series is based on 2020.10-rc1 + mt7622 PCIe series [1] + R64 DTS [2]

[1] https://patchwork.ozlabs.org/project/uboot/list/?series=194888
[2] https://patchwork.ozlabs.org/project/uboot/list/?series=194922

v2->v3: some changes in ahci-driver based on chunfeng yun's review
- alphabetic sort of includes
- use reset_ctl_bulk
- devfdt_remap_addr_index instead of map_physmem(devfdt_get_addr())
- move ahci_uc_priv to mtk_ahci_priv
v1->v2: fix coding styles reported by checkpatch.pl

Frank Wunderlich (5):
arm: dts: mt7622: add SATA reset constants
phy: mtk-tphy: add PHY_TYPE_SATA
reset: add basic reset controller for pciesys
ahci: mediatek: add ahci driver
dts: r64: add sata- and asm_sel nodes

 arch/arm/dts/mt7622-bpi-r64.dts          |   9 ++
 arch/arm/dts/mt7622.dtsi                 |  32 ++++++
 drivers/ata/Kconfig                      |   8 ++
 drivers/ata/Makefile                     |   1 +
 drivers/ata/mtk_ahci.c                   | 130 +++++++++++++++++++++++
 drivers/clk/mediatek/clk-mt7622.c        |  15 +++
 drivers/phy/phy-mtk-tphy.c               | 105 ++++++++++++++++++
 include/dt-bindings/reset/mt7629-reset.h |   5 +-
 8 files changed, 304 insertions(+), 1 deletion(-)
 create mode 100644 drivers/ata/mtk_ahci.c
Signature · 1 line
2.25.1
#1 lore raw

PATCH v3 1/5 arm: dts: mt7622: add SATA reset constants

From: Frank Wunderlich <[email protected]>

add reset constants used for SATA to header file

---
 include/dt-bindings/reset/mt7629-reset.h | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)
include/dt-bindings/reset/mt7629-reset.h +4 -1
index 8f1634f7a6..311a5cb3d0 100644
@@ -6,7 +6,10 @@
 #ifndef _DT_BINDINGS_MTK_RESET_H_
 #define _DT_BINDINGS_MTK_RESET_H_
 
-/* PCIe Subsystem resets */
+/* PCIe/SATA Subsystem resets */
+#define MT7622_SATA_PHY_REG_RST			12
+#define MT7622_SATA_PHY_SW_RST			13
+#define MT7622_SATA_AXI_BUS_RST			15
 #define PCIE1_CORE_RST			19
 #define PCIE1_MMIO_RST			20
 #define PCIE1_HRST			21
Signature · 1 line
2.25.1
#6 lore raw

PATCH v3 2/5 phy: mtk-tphy: add PHY_TYPE_SATA

In reply to Frank Wunderlich

From: Frank Wunderlich <[email protected]>

add support for PHY_TYPE_SATA to Mediateks TPHY driver

---
 drivers/phy/phy-mtk-tphy.c | 105 +++++++++++++++++++++++++++++++++++++
 1 file changed, 105 insertions(+)
drivers/phy/phy-mtk-tphy.c +105 -0
index 1e65c24356..326227a30d 100644
@@ -175,6 +175,65 @@
 #define XC3_RG_U3_XTAL_RX_PWD		BIT(9)
 #define XC3_RG_U3_FRC_XTAL_RX_PWD	BIT(8)
 
+/* SATA register setting */
+#define PHYD_CTRL_SIGNAL_MODE4		0x1c
+/* CDR Charge Pump P-path current adjustment */
+#define RG_CDR_BICLTD1_GEN1_MSK		GENMASK(23, 20)
+#define RG_CDR_BICLTD1_GEN1_VAL(x)	((0xf & (x)) << 20)
+#define RG_CDR_BICLTD0_GEN1_MSK		GENMASK(11, 8)
+#define RG_CDR_BICLTD0_GEN1_VAL(x)	((0xf & (x)) << 8)
+
+#define PHYD_DESIGN_OPTION2		0x24
+/* Symbol lock count selection */
+#define RG_LOCK_CNT_SEL_MSK		GENMASK(5, 4)
+#define RG_LOCK_CNT_SEL_VAL(x)		((0x3 & (x)) << 4)
+
+#define PHYD_DESIGN_OPTION9		0x40
+/* COMWAK GAP width window */
+#define RG_TG_MAX_MSK			GENMASK(20, 16)
+#define RG_TG_MAX_VAL(x)		((0x1f & (x)) << 16)
+/* COMINIT GAP width window */
+#define RG_T2_MAX_MSK			GENMASK(13, 8)
+#define RG_T2_MAX_VAL(x)		((0x3f & (x)) << 8)
+/* COMWAK GAP width window */
+#define RG_TG_MIN_MSK			GENMASK(7, 5)
+#define RG_TG_MIN_VAL(x)		((0x7 & (x)) << 5)
+/* COMINIT GAP width window */
+#define RG_T2_MIN_MSK			GENMASK(4, 0)
+#define RG_T2_MIN_VAL(x)		(0x1f & (x))
+
+#define ANA_RG_CTRL_SIGNAL1		0x4c
+/* TX driver tail current control for 0dB de-empahsis mdoe for Gen1 speed */
+#define RG_IDRV_0DB_GEN1_MSK		GENMASK(13, 8)
+#define RG_IDRV_0DB_GEN1_VAL(x)		((0x3f & (x)) << 8)
+
+#define ANA_RG_CTRL_SIGNAL4		0x58
+#define RG_CDR_BICLTR_GEN1_MSK		GENMASK(23, 20)
+#define RG_CDR_BICLTR_GEN1_VAL(x)	((0xf & (x)) << 20)
+/* Loop filter R1 resistance adjustment for Gen1 speed */
+#define RG_CDR_BR_GEN2_MSK		GENMASK(10, 8)
+#define RG_CDR_BR_GEN2_VAL(x)		((0x7 & (x)) << 8)
+
+#define ANA_RG_CTRL_SIGNAL6		0x60
+/* I-path capacitance adjustment for Gen1 */
+#define RG_CDR_BC_GEN1_MSK		GENMASK(28, 24)
+#define RG_CDR_BC_GEN1_VAL(x)		((0x1f & (x)) << 24)
+#define RG_CDR_BIRLTR_GEN1_MSK		GENMASK(4, 0)
+#define RG_CDR_BIRLTR_GEN1_VAL(x)	(0x1f & (x))
+
+#define ANA_EQ_EYE_CTRL_SIGNAL1		0x6c
+/* RX Gen1 LEQ tuning step */
+#define RG_EQ_DLEQ_LFI_GEN1_MSK		GENMASK(11, 8)
+#define RG_EQ_DLEQ_LFI_GEN1_VAL(x)	((0xf & (x)) << 8)
+
+#define ANA_EQ_EYE_CTRL_SIGNAL4		0xd8
+#define RG_CDR_BIRLTD0_GEN1_MSK		GENMASK(20, 16)
+#define RG_CDR_BIRLTD0_GEN1_VAL(x)	((0x1f & (x)) << 16)
+
+#define ANA_EQ_EYE_CTRL_SIGNAL5		0xdc
+#define RG_CDR_BIRLTD0_GEN3_MSK		GENMASK(4, 0)
+#define RG_CDR_BIRLTD0_GEN3_VAL(x)	(0x1f & (x))
+
 enum mtk_phy_version {
 	MTK_TPHY_V1 = 1,
 	MTK_TPHY_V2,
@@ -372,6 +431,45 @@ static void pcie_phy_instance_init(struct mtk_tphy *tphy,
 	udelay(3000);
 }
 
+static void sata_phy_instance_init(struct mtk_tphy *tphy,
+				   struct mtk_phy_instance *instance)
+{
+	struct u3phy_banks *u3_banks = &instance->u3_banks;
+
+	clrsetbits_le32(u3_banks->phyd + ANA_RG_CTRL_SIGNAL6,
+			RG_CDR_BIRLTR_GEN1_MSK | RG_CDR_BC_GEN1_MSK,
+			RG_CDR_BIRLTR_GEN1_VAL(0x6) |
+			RG_CDR_BC_GEN1_VAL(0x1a));
+	clrsetbits_le32(u3_banks->phyd + ANA_EQ_EYE_CTRL_SIGNAL4,
+			RG_CDR_BIRLTD0_GEN1_MSK,
+			RG_CDR_BIRLTD0_GEN1_VAL(0x18));
+	clrsetbits_le32(u3_banks->phyd + ANA_EQ_EYE_CTRL_SIGNAL5,
+			RG_CDR_BIRLTD0_GEN3_MSK,
+			RG_CDR_BIRLTD0_GEN3_VAL(0x06));
+	clrsetbits_le32(u3_banks->phyd + ANA_RG_CTRL_SIGNAL4,
+			RG_CDR_BICLTR_GEN1_MSK | RG_CDR_BR_GEN2_MSK,
+			RG_CDR_BICLTR_GEN1_VAL(0x0c) |
+			RG_CDR_BR_GEN2_VAL(0x07));
+	clrsetbits_le32(u3_banks->phyd + PHYD_CTRL_SIGNAL_MODE4,
+			RG_CDR_BICLTD0_GEN1_MSK | RG_CDR_BICLTD1_GEN1_MSK,
+			RG_CDR_BICLTD0_GEN1_VAL(0x08) |
+			RG_CDR_BICLTD1_GEN1_VAL(0x02));
+	clrsetbits_le32(u3_banks->phyd + PHYD_DESIGN_OPTION2,
+			RG_LOCK_CNT_SEL_MSK,
+			RG_LOCK_CNT_SEL_VAL(0x02));
+	clrsetbits_le32(u3_banks->phyd + PHYD_DESIGN_OPTION9,
+			RG_T2_MIN_MSK | RG_TG_MIN_MSK |
+			RG_T2_MAX_MSK | RG_TG_MAX_MSK,
+			RG_T2_MIN_VAL(0x12) | RG_TG_MIN_VAL(0x04) |
+			RG_T2_MAX_VAL(0x31) | RG_TG_MAX_VAL(0x0e));
+	clrsetbits_le32(u3_banks->phyd + ANA_RG_CTRL_SIGNAL1,
+			RG_IDRV_0DB_GEN1_MSK,
+			RG_IDRV_0DB_GEN1_VAL(0x20));
+	clrsetbits_le32(u3_banks->phyd + ANA_EQ_EYE_CTRL_SIGNAL1,
+			RG_EQ_DLEQ_LFI_GEN1_MSK,
+			RG_EQ_DLEQ_LFI_GEN1_VAL(0x03));
+}
+
 static void pcie_phy_instance_power_on(struct mtk_tphy *tphy,
 				       struct mtk_phy_instance *instance)
 {
@@ -414,6 +512,9 @@ static void phy_v1_banks_init(struct mtk_tphy *tphy,
 		u3_banks->phyd = instance->port_base + SSUSB_SIFSLV_V1_U3PHYD;
 		u3_banks->phya = instance->port_base + SSUSB_SIFSLV_V1_U3PHYA;
 		break;
+	case PHY_TYPE_SATA:
+		u3_banks->phyd = instance->port_base + SSUSB_SIFSLV_V1_U3PHYD;
+		break;
 	default:
 		dev_err(tphy->dev, "incompatible PHY type\n");
 		return;
@@ -474,6 +575,9 @@ static int mtk_phy_init(struct phy *phy)
 	case PHY_TYPE_PCIE:
 		pcie_phy_instance_init(tphy, instance);
 		break;
+	case PHY_TYPE_SATA:
+		sata_phy_instance_init(tphy, instance);
+		break;
 	default:
 		dev_err(tphy->dev, "incompatible PHY type\n");
 		return -EINVAL;
@@ -552,6 +656,7 @@ static int mtk_phy_xlate(struct phy *phy,
 	instance->type = args->args[1];
 	if (!(instance->type == PHY_TYPE_USB2 ||
 	      instance->type == PHY_TYPE_USB3 ||
+	      instance->type == PHY_TYPE_SATA ||
 	      instance->type == PHY_TYPE_PCIE)) {
 		dev_err(phy->dev, "unsupported device type\n");
 		return -EINVAL;
Signature · 1 line
2.25.1
#8 lore raw

PATCH v3 3/5 reset: add basic reset controller for pciesys

In reply to Frank Wunderlich

From: Frank Wunderlich <[email protected]>

bind reset controller to pciesys

---
 drivers/clk/mediatek/clk-mt7622.c | 15 +++++++++++++++
 1 file changed, 15 insertions(+)
drivers/clk/mediatek/clk-mt7622.c +15 -0
index bd86b5b974..d53ed69189 100644
@@ -594,6 +594,20 @@ static int mt7622_pciesys_probe(struct udevice *dev)
 	return mtk_common_clk_gate_init(dev, &mt7622_clk_tree, pcie_cgs);
 }
 
+static int mt7622_pciesys_bind(struct udevice *dev)
+{
+	int ret = 0;
+
+	if (IS_ENABLED(CONFIG_RESET_MEDIATEK)) {
+//	PCIESYS uses in linux also 0x34 = ETHSYS reset controller
+	ret = mediatek_reset_bind(dev, ETHSYS_HIFSYS_RST_CTRL_OFS, 1);
+	if (ret)
+		debug("Warning: failed to bind reset controller\n");
+	}
+
+	return ret;
+}
+
 static int mt7622_ethsys_probe(struct udevice *dev)
 {
 	return mtk_common_clk_gate_init(dev, &mt7622_clk_tree, eth_cgs);
@@ -710,6 +724,7 @@ U_BOOT_DRIVER(mtk_clk_pciesys) = {
 	.id = UCLASS_CLK,
 	.of_match = mt7622_pciesys_compat,
 	.probe = mt7622_pciesys_probe,
+	.bind = mt7622_pciesys_bind,
 	.priv_auto_alloc_size = sizeof(struct mtk_cg_priv),
 	.ops = &mtk_clk_gate_ops,
 };
Signature · 1 line
2.25.1
#10 lore raw

PATCH v3 4/5 ahci: mediatek: add ahci driver

In reply to Frank Wunderlich

From: Frank Wunderlich <[email protected]>

add AHCI driver ported from linux

https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/ata/ahci_mtk.c

---
v2->v3:
- alphabetic sort of includes
- use reset_ctl_bulk
- devfdt_remap_addr_index instead of map_physmem(devfdt_get_addr())
- move ahci_uc_priv to mtk_ahci_priv

---
 drivers/ata/Kconfig    |   8 +++
 drivers/ata/Makefile   |   1 +
 drivers/ata/mtk_ahci.c | 130 +++++++++++++++++++++++++++++++++++++++++
 3 files changed, 139 insertions(+)
 create mode 100644 drivers/ata/mtk_ahci.c
drivers/ata/Kconfig +8 -0
index d8c9756c2a..f2f8275aec 100644
@@ -130,4 +130,12 @@ config AHCI_MVEBU
 	  onboard AHCI SATA.
 
 	  If unsure, say N.
+
+config MTK_AHCI
+	bool "Enable Mediatek AHCI driver support"
+	depends on AHCI
+	help
+	  Enable this driver to support Sata devices through
+	  Mediatek AHCI controller (e.g. MT7622).
+
 endmenu
drivers/ata/Makefile +1 -0
index a69edb10f7..98fb480700 100644
@@ -19,3 +19,4 @@ obj-$(CONFIG_SATA_SIL) += sata_sil.o
 obj-$(CONFIG_SANDBOX) += sata_sandbox.o
 obj-$(CONFIG_AHCI_MVEBU) += ahci_mvebu.o
 obj-$(CONFIG_SUNXI_AHCI) += ahci_sunxi.o
+obj-$(CONFIG_MTK_AHCI) += mtk_ahci.o
drivers/ata/mtk_ahci.c new file +130 -0

130 lines not on this page · raw message

Signature · 1 line
2.25.1
#12 lore raw

PATCH v3 5/5 dts: r64: add sata- and asm_sel nodes

In reply to Frank Wunderlich

From: Frank Wunderlich <[email protected]>

asm_sel is for switching between sata and pcie mode on r64 there is GPIO90 connected to ASM1480 which switches RX/TX pairs to PCIe/SATA connector output-low means sata-controller is active

with 2020-10 now reg is also needed for the phy itself

---
 arch/arm/dts/mt7622-bpi-r64.dts |  9 +++++++++
 arch/arm/dts/mt7622.dtsi        | 32 ++++++++++++++++++++++++++++++++
 2 files changed, 41 insertions(+)
arch/arm/dts/mt7622-bpi-r64.dts +9 -0
index c89e816878..51287cea3a 100644
@@ -235,3 +235,12 @@
 		full-duplex;
 	};
 };
+
+&gpio {
+	/*gpio 90 for setting mode to sata*/
+	asm_sel {
+		gpio-hog;
+		gpios = <90 GPIO_ACTIVE_HIGH>;
+		output-low;
+	};
+};
arch/arm/dts/mt7622.dtsi +32 -0
index fec071643e..c43ad65702 100644
@@ -10,6 +10,7 @@
 #include <dt-bindings/power/mt7629-power.h>
 #include <dt-bindings/reset/mt7629-reset.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/phy/phy.h>
 
 / {
 	compatible = "mediatek,mt7622";
@@ -270,6 +271,37 @@
 		};
 	};
 
+	sata: sata at 1a200000 {
+		compatible = "mediatek,mtk-ahci";
+		reg = <0x1a200000 0x1100>;
+		resets = <&pciesys MT7622_SATA_AXI_BUS_RST>,
+			<&pciesys MT7622_SATA_PHY_SW_RST>,
+			<&pciesys MT7622_SATA_PHY_REG_RST>;
+		reset-names = "axi", "sw", "reg";
+		mediatek,phy-mode = <&pciesys>;
+		ports-implemented = <0x1>;
+		phys = <&sata_port PHY_TYPE_SATA>;
+		phy-names = "sata-phy";
+		status = "okay";
+	};
+
+	sata_phy: sata-phy at 1a243000 {
+		compatible = "mediatek,generic-tphy-v1";
+		reg = <0x1a243000 0x0100>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		status = "okay";
+
+		sata_port: sata-phy at 1a243000 {
+			reg = <0x1a243000 0x0100>;
+			clocks = <&topckgen CLK_TOP_ETH_500M>;
+			clock-names = "ref";
+			#phy-cells = <1>;
+			status = "okay";
+		};
+	};
+
 	ethsys: syscon at 1b000000 {
 		compatible = "mediatek,mt7622-ethsys", "syscon";
 		reg = <0x1b000000 0x1000>;
Signature · 1 line
2.25.1
#2 lore raw

PATCH v3 1/5 arm: dts: mt7622: add SATA reset constants

In reply to Frank Wunderlich
Quoted 5 lines · Frank Wunderlich

From: Frank Wunderlich <[email protected]>

add reset constants used for SATA to header file

Applied to u-boot/master, thanks!

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 659 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200820/57c946c0/attachment.sig>
#7 lore raw

PATCH v3 2/5 phy: mtk-tphy: add PHY_TYPE_SATA

In reply to Frank Wunderlich
Quoted 6 lines · Frank Wunderlich

From: Frank Wunderlich <[email protected]>

add support for PHY_TYPE_SATA to Mediateks TPHY driver

Applied to u-boot/master, thanks!

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 659 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200820/18dda5a2/attachment.sig>
#9 lore raw

PATCH v3 3/5 reset: add basic reset controller for pciesys

In reply to Frank Wunderlich
Quoted 5 lines · Frank Wunderlich

From: Frank Wunderlich <[email protected]>

bind reset controller to pciesys

Applied to u-boot/master, thanks!

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 659 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200820/cfb169a0/attachment.sig>
#11 lore raw

PATCH v3 4/5 ahci: mediatek: add ahci driver

In reply to Frank Wunderlich
Quoted 7 lines · Frank Wunderlich

From: Frank Wunderlich <[email protected]>

add AHCI driver ported from linux

https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/ata/ahci_mtk.c

Applied to u-boot/master, thanks!

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 659 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200820/b0c36648/attachment.sig>
#13 lore raw

PATCH v3 5/5 dts: r64: add sata- and asm_sel nodes

In reply to Frank Wunderlich
Quoted 10 lines · Frank Wunderlich

From: Frank Wunderlich <[email protected]>

asm_sel is for switching between sata and pcie mode on r64 there is GPIO90 connected to ASM1480 which switches RX/TX pairs to PCIe/SATA connector output-low means sata-controller is active

with 2020-10 now reg is also needed for the phy itself

Applied to u-boot/master, thanks!

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 659 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200820/8ab1c18f/attachment.sig>
#3 lore raw

Aw: Re: [PATCH v3 1/5] arm: dts: mt7622: add SATA reset constants

In reply to Tom Rini

Hi tom,

this series (and some more) was superseeded by this one:

https://patchwork.ozlabs.org/project/uboot/cover/20200820105826.6229-1-linux at fw-web.de/

see coverletter of v1 of this series:
https://patchwork.ozlabs.org/project/uboot/cover/20200816082431.5087-1-linux at fw-web.de/

regards Frank

Quoted 19 lines

Gesendet: Donnerstag, 20. August 2020 um 14:40 Uhr
Von: "Tom Rini" <[email protected]>
An: "Frank Wunderlich" <[email protected]>
Cc: u-boot at lists.denx.de, "Frank Wunderlich" <[email protected]>, "GSS_MTK_Uboot_upstream" <[email protected]>, "Ryder Lee" <[email protected]>, "Weijie Gao" <[email protected]>, "Lukasz Majewski" <[email protected]>
Betreff: Re: [PATCH v3 1/5] arm: dts: mt7622: add SATA reset constants

Quoted 5 lines · Frank Wunderlich

From: Frank Wunderlich <[email protected]>

add reset constants used for SATA to header file

Applied to u-boot/master, thanks!

--
Tom

#4 lore raw

PATCH v3 1/5 arm: dts: mt7622: add SATA reset constants

Quoted 8 lines · Frank Wunderlich

Hi tom,

this series (and some more) was superseeded by this one:

https://patchwork.ozlabs.org/project/uboot/cover/20200820105826.6229-1-linux at fw-web.de/

see coverletter of v1 of this series:
https://patchwork.ozlabs.org/project/uboot/cover/20200816082431.5087-1-linux at fw-web.de/

Sigh, sorry about that. Please do a v5 of the deltas that aren't in now, thanks.

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 659 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200820/c13205b7/attachment.sig>
#5 lore raw

Aw: Re: Re: [PATCH v3 1/5] arm: dts: mt7622: add SATA reset constants

Quoted 11 lines

Gesendet: Donnerstag, 20. August 2020 um 15:25 Uhr
Von: "Tom Rini" <[email protected]>

Quoted 6 lines

this series (and some more) was superseeded by this one:

https://patchwork.ozlabs.org/project/uboot/cover/20200820105826.6229-1-linux at fw-web.de/

see coverletter of v1 of this series:
https://patchwork.ozlabs.org/project/uboot/cover/20200816082431.5087-1-linux at fw-web.de/

Sigh, sorry about that. Please do a v5 of the deltas that aren't in now, thanks.

it's on the way...just that you ignore the other standalone parts. have all put into one series to make it easier for you...but forgot to mention it in the old parts :( sorry about that

Regards Frank