ARM: dts: stm32: Adjust PLL4 settings on AV96 again
Subsystems (3)
PATCH 1/1 ARM: dts: stm32: Adjust PLL4 settings on AV96 again
PLL4Q is supplying both FDCAN and LTDC. In case HDMI is in use, the 50 MHz generated from PLL4Q cannot be divided well enough to produce accurate clock for HDMI pixel clock. Adjust it to generate 74.25 MHz instead. The PLL4P/PLL4R are generating 99 MHz instead of 100 MHz, which is in tolerance for the SDMMC.
---
NOTE: Thanks to Gerald for this suggestion.
--- arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi +2 -2
@@ -132,11 +132,11 @@ u-boot,dm-pre-reloc; }; - /* VCO = 600.0 MHz => P = 100, Q = 50, R = 100 */ + /* VCO = 600.0 MHz => P = 99, Q = 74, R = 99 */ pll4: st,pll at 3 { compatible = "st,stm32mp1-pll"; reg = <3>; - cfg = < 1 49 5 11 5 PQR(1,1,1) >; + cfg = < 3 98 5 7 5 PQR(1,1,1) >; u-boot,dm-pre-reloc; }; };
Signature · 1 line
2.28.0
PATCH 1/1 ARM: dts: stm32: Adjust PLL4 settings on AV96 again
Hi Marek,
Quoted 39 lines
From: Marek Vasut <[email protected]>
Sent: samedi 22 ao?t 2020 22:45PLL4Q is supplying both FDCAN and LTDC. In case HDMI is in use, the 50 MHz generated from PLL4Q cannot be divided well enough to produce accurate clock for HDMI pixel clock. Adjust it to generate 74.25 MHz instead. The PLL4P/PLL4R are generating 99 MHz instead of 100 MHz, which is in tolerance for the SDMMC.
Signed-off-by Marek Vasut <[email protected]>Cc Gerald Baeza <[email protected]>Cc Patrick Delaunay <[email protected]>Cc Patrice Chotard <[email protected]>---
NOTE: Thanks to Gerald for this suggestion.--- arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi +2
-3@@ -132,11 +132,11 @@ u-boot,dm-pre-reloc; }; - /* VCO = 600.0 MHz => P = 100, Q = 50, R = 100 */ + /* VCO = 600.0 MHz => P = 99, Q = 74, R = 99 */ pll4: st,pll at 3 { compatible = "st,stm32mp1-pll"; reg = <3>; - cfg = < 1 49 5 11 5 PQR(1,1,1) >; + cfg = < 3 98 5 7 5 PQR(1,1,1) >; u-boot,dm-pre-reloc; }; }; --
Quoted 1 line
2.28.0
Applied to u-boot-stm/master, thanks!
Thanks
Patrick