pinctrl: mcp23s08: Improve error messaging in ->probe()
Subsystems (2)
PATCH 1/1 pinctrl: mcp23s08: Improve error messaging in ->probe()
Print particular message in each of error case in the ->probe(). While here, use dev_err_probe() for that.
Cc Krzysztof Kozlowski <[email protected]>
Signed-off-by Andy Shevchenko <[email protected]>
--- drivers/pinctrl/pinctrl-mcp23s08.c | 23 +++++++++++------------ 1 file changed, 11 insertions(+), 12 deletions(-)
drivers/pinctrl/pinctrl-mcp23s08.c +11 -12
@@ -564,7 +564,7 @@ int mcp23s08_probe_one(struct mcp23s08 *mcp, struct device *dev, ret =mcp_read (mcp,MCP_IOCON , &status);if (ret <0 ) - goto fail; +return dev_err_probe (dev, ret,"can't identify chip %d\n" , addr); mcp->irq_controller =device_property_read_bool (dev,"interrupt-controller" );
@@ -598,7 +598,7 @@ int mcp23s08_probe_one(struct mcp23s08 *mcp, struct device *dev, ret =mcp_write (mcp,MCP_IOCON , status);if (ret <0 ) - goto fail; +return dev_err_probe (dev, ret,"can't write IOCON %d\n" , addr); }if (mcp->irq && mcp->irq_controller) {
@@ -616,7 +616,7 @@ int mcp23s08_probe_one(struct mcp23s08 *mcp, struct device *dev, ret =devm_gpiochip_add_data (dev, &mcp->chip, mcp);if (ret <0 ) - goto fail; +return dev_err_probe (dev, ret,"can't add GPIO chip\n" ); mcp->pinctrl_desc.pctlops = &mcp_pinctrl_ops; mcp->pinctrl_desc.confops = &mcp_pinconf_ops;
@@ -628,18 +628,17 @@ int mcp23s08_probe_one(struct mcp23s08 *mcp, struct device *dev, mcp->pinctrl_desc.owner =THIS_MODULE ; mcp->pctldev =devm_pinctrl_register (dev, &mcp->pinctrl_desc, mcp); -if (IS_ERR (mcp->pctldev)) { - ret =PTR_ERR (mcp->pctldev); - goto fail; - } +if (IS_ERR (mcp->pctldev)) +return dev_err_probe (dev,PTR_ERR (mcp->pctldev),"can't register controller\n" ); -if (mcp->irq) +if (mcp->irq) { ret =mcp23s08_irq_setup (mcp); +if (ret) +return dev_err_probe (dev, ret,"can't setup IRQ\n" ); + } -fail: -if (ret <0 ) -dev_dbg (dev,"can't setup chip %d, --> %d\n" , addr, ret); -return ret; +return 0 ; }EXPORT_SYMBOL_GPL (mcp23s08_probe_one); +MODULE_LICENSE ("GPL" );
Signature · 1 line
2.28.0
Quoted 5 lines · Andy Shevchenko
Print particular message in each of error case in the ->probe(). While here, use
dev_err_probe()for that.Cc Krzysztof Kozlowski <[email protected]>Signed-off-by Andy Shevchenko <[email protected]>
Patch applied.
Yours,
Linus Walleij