USB: new USB control message helper functions
Subsystems (4)
Greg Kroah-Hartman
maintainercover USB: new USB control message helper functions
In a recent discussion about a USB networking bug found by syzbot, and fixed by Himadri Pandya, the design of the existing usb_control_msg() call was brought up as not being the "nicest" thing to use by Dmitry Vyukov:
https://lore.kernel.org/r/CACT4Y+YbDODLRFn8M5QcY4CazhpeCaunJnP_udXtAs0rYoASSg@mail.gmail.com
The function makes it hard to get right, in that it will return the number of bytes sent/received, but almost no one checks to see if a short read/write happens. With a malicious, or broken, USB device, this can cause drivers to act on data that they did not anticipate, and sometimes copy internal kernel data out to userspace.
So let's fix this up by creating two new functions, usb_control_msg_send() and usb_control_msg_recv(). These functions either complete the full transation, or they return an error, a short send/recv is now an error.
They also accept data off of the stack, saving individual drivers the pain of having to constantly allocate memory on their own for tiny messages, thereby saving overall kernel code space.
The api also does not require a raw USB "pipe" to be sent to the function, as we know the direction, so just pass in the endpoint number instead, again making it easier on the USB driver author to use.
This series first takes a helper function out of the sound core for verifying USB endpoints to be able to use internally, and then adds the new functions, converts over some internal USB code to use them, and then starts to clean up some drivers using these new functions, as an example of the savings that can happen by using these functions.
Thanks to Dmitry and Himadri for the idea on how to do all of this.
greg k-h
Greg Kroah-Hartman (10):
USB: move snd_usb_pipe_sanity_check into the USB core
USB: add usb_control_msg_send() and usb_control_msg_recv()
USB: core: message.c: use usb_control_msg_send() in a few places
USB: core: hub.c: use usb_control_msg_send() in a few places
USB: legousbtower: use usb_control_msg_recv()
sound: usx2y: move to use usb_control_msg_send()
sound: 6fire: move to use usb_control_msg_send() and
usb_control_msg_recv()
sound: line6: move to use usb_control_msg_send() and
usb_control_msg_recv()
sound: hiface: move to use usb_control_msg_send()
Bluetooth: ath3k: use usb_control_msg_send() and
usb_control_msg_recv()
drivers/bluetooth/ath3k.c | 90 +++++------------ drivers/usb/core/hub.c | 128 +++++++++--------------- drivers/usb/core/message.c | 171 ++++++++++++++++++++++++++++---- drivers/usb/core/urb.c | 29 ++++-- drivers/usb/misc/legousbtower.c | 60 ++++------- include/linux/usb.h | 7 ++ sound/usb/6fire/firmware.c | 38 +++---- sound/usb/helper.c | 16 +-- sound/usb/helper.h | 1 - sound/usb/hiface/pcm.c | 14 ++- sound/usb/line6/driver.c | 69 +++++-------- sound/usb/line6/podhd.c | 17 ++-- sound/usb/line6/toneport.c | 8 +- sound/usb/mixer_scarlett_gen2.c | 2 +- sound/usb/quirks.c | 12 +-- sound/usb/usx2y/us122l.c | 42 ++------ 16 files changed, 345 insertions(+), 359 deletions(-)
Signature · 1 line
2.28.0
Greg Kroah-Hartman
maintainerPATCH 1/10 USB: move snd_usb_pipe_sanity_check into the USB core
snd_usb_pipe_sanity_check() is a great function, so let's move it into the USB core so that other parts of the kernel, including the USB core, can call it.
Name it usb_pipe_type_check() to match the existing usb_urb_ep_type_check() call, which now uses this function.
--- drivers/usb/core/urb.c | 29 ++++++++++++++++++++++------- include/linux/usb.h | 1 + sound/usb/helper.c | 16 +--------------- sound/usb/helper.h | 1 - sound/usb/mixer_scarlett_gen2.c | 2 +- sound/usb/quirks.c | 12 ++++++------ 6 files changed, 31 insertions(+), 30 deletions(-)
drivers/usb/core/urb.c +22 -7
@@ -192,24 +192,39 @@ static const int pipetypes[4] = { };/** -* usb_urb_ep_type_check - sanity check of endpoint in the given urb -* @urb: urb to be checked +* usb_pipe_type_check - sanity check of a specific pipe for a usb device +* @dev: struct usb_device to be checked +* @pipe: pipe to check * * This performs a light-weight sanity check for the endpoint in the -* given urb. It returns 0 if the urb contains a valid endpoint, otherwise -* a negative error code. +* given usb device. It returns 0 if the pipe is a valid for the specific usb +* device, otherwise a negative error code. */ -int usb_urb_ep_type_check (const struct urb *urb) +int usb_pipe_type_check (struct usb_device *dev,unsigned int pipe) {const struct usb_host_endpoint *ep; - ep =usb_pipe_endpoint (urb->dev, urb->pipe); + ep =usb_pipe_endpoint (dev, pipe);if (!ep)return -EINVAL ; -if (usb_pipetype (urb->pipe) != pipetypes[usb_endpoint_type (&ep->desc)]) +if (usb_pipetype (pipe) != pipetypes[usb_endpoint_type (&ep->desc)])return -EINVAL ;return 0 ; } +EXPORT_SYMBOL_GPL (usb_pipe_type_check); + +/** +* usb_urb_ep_type_check - sanity check of endpoint in the given urb +* @urb: urb to be checked +* +* This performs a light-weight sanity check for the endpoint in the +* given urb. It returns 0 if the urb contains a valid endpoint, otherwise +* a negative error code. +*/ +int usb_urb_ep_type_check (const struct urb *urb) +{ +return usb_pipe_type_check (urb->dev, urb->pipe); +}EXPORT_SYMBOL_GPL (usb_urb_ep_type_check);/**
include/linux/usb.h +1 -0
@@ -1764,6 +1764,7 @@ static inline int usb_urb_dir_out(struct urb *urb)return (urb->transfer_flags &URB_DIR_MASK ) ==URB_DIR_OUT ; } +int usb_pipe_type_check (struct usb_device *dev,unsigned int pipe);int usb_urb_ep_type_check (const struct urb *urb); void *usb_alloc_coherent(struct usb_device *dev, size_t size,
sound/usb/helper.c +1 -15
@@ -63,20 +63,6 @@ void *snd_usb_find_csint_desc(void *buffer, int buflen, void *after, u8 dsubtypereturn NULL ; } -/* check the validity of pipe and EP types */ -int snd_usb_pipe_sanity_check (struct usb_device *dev,unsigned int pipe) -{ -static const int pipetypes[4 ] = { -PIPE_CONTROL ,PIPE_ISOCHRONOUS ,PIPE_BULK ,PIPE_INTERRUPT - }; -struct usb_host_endpoint *ep; - - ep =usb_pipe_endpoint (dev, pipe); -if (!ep ||usb_pipetype (pipe) != pipetypes[usb_endpoint_type (&ep->desc)]) -return -EINVAL ; -return 0 ; -} -/* * Wrapper for usb_control_msg(). * Allocates a temp buffer to prevent dmaing from/to the stack.
@@ -89,7 +75,7 @@ int snd_usb_ctl_msg(struct usb_device *dev, unsigned int pipe, __u8 request,void *buf =NULL ;int timeout; -if (snd_usb_pipe_sanity_check (dev, pipe)) +if (usb_pipe_type_check (dev, pipe))return -EINVAL ;if (size >0 ) {
sound/usb/helper.h +0 -1
@@ -7,7 +7,6 @@ unsigned int snd_usb_combine_bytes(unsigned char *bytes, int size);void *snd_usb_find_desc (void *descstart,int desclen,void *after,u8 dtype);void *snd_usb_find_csint_desc (void *descstart,int desclen,void *after,u8 dsubtype); -int snd_usb_pipe_sanity_check (struct usb_device *dev,unsigned int pipe);int snd_usb_ctl_msg (struct usb_device *dev,unsigned int pipe,__u8 request,__u8 requesttype,__u16 value,__u16 index,void *data,__u16 size);
sound/usb/mixer_scarlett_gen2.c +1 -1
@@ -1978,7 +1978,7 @@ static int scarlett2_mixer_status_create(struct usb_mixer_interface *mixer)return 0 ; } -if (snd_usb_pipe_sanity_check (dev, pipe)) +if (usb_pipe_type_check (dev, pipe))return -EINVAL ; mixer->urb =usb_alloc_urb (0 ,GFP_KERNEL );
sound/usb/quirks.c +6 -6
@@ -846,7 +846,7 @@ static int snd_usb_accessmusic_boot_quirk(struct usb_device *dev)static const u8 seq[] = {0x4e ,0x73 ,0x52 ,0x01 };void *buf; -if (snd_usb_pipe_sanity_check (dev,usb_sndintpipe (dev,0x05 ))) +if (usb_pipe_type_check (dev,usb_sndintpipe (dev,0x05 )))return -EINVAL ; buf =kmemdup (seq,ARRAY_SIZE (seq),GFP_KERNEL );if (!buf)
@@ -875,7 +875,7 @@ static int snd_usb_nativeinstruments_boot_quirk(struct usb_device *dev) {int ret; -if (snd_usb_pipe_sanity_check (dev,usb_sndctrlpipe (dev,0 ))) +if (usb_pipe_type_check (dev,usb_sndctrlpipe (dev,0 )))return -EINVAL ; ret = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), 0xaf, USB_TYPE_VENDOR | USB_RECIP_DEVICE,
@@ -984,7 +984,7 @@ static int snd_usb_axefx3_boot_quirk(struct usb_device *dev)dev_dbg (&dev->dev,"Waiting for Axe-Fx III to boot up...\n" ); -if (snd_usb_pipe_sanity_check (dev,usb_sndctrlpipe (dev,0 ))) +if (usb_pipe_type_check (dev,usb_sndctrlpipe (dev,0 )))return -EINVAL ;/* If the Axe-Fx III has not fully booted, it will timeout when trying * to enable the audio streaming interface. A more generous timeout is
@@ -1018,7 +1018,7 @@ static int snd_usb_motu_microbookii_communicate(struct usb_device *dev, u8 *buf, {int err, actual_length; -if (snd_usb_pipe_sanity_check (dev,usb_sndintpipe (dev,0x01 ))) +if (usb_pipe_type_check (dev,usb_sndintpipe (dev,0x01 )))return -EINVAL ; err =usb_interrupt_msg (dev,usb_sndintpipe (dev,0x01 ), buf, *length, &actual_length,1000 );
@@ -1030,7 +1030,7 @@ static int snd_usb_motu_microbookii_communicate(struct usb_device *dev, u8 *buf,memset (buf,0 , buf_size); -if (snd_usb_pipe_sanity_check (dev,usb_rcvintpipe (dev,0x82 ))) +if (usb_pipe_type_check (dev,usb_rcvintpipe (dev,0x82 )))return -EINVAL ; err =usb_interrupt_msg (dev,usb_rcvintpipe (dev,0x82 ), buf, buf_size, &actual_length,1000 );
@@ -1117,7 +1117,7 @@ static int snd_usb_motu_m_series_boot_quirk(struct usb_device *dev) {int ret; -if (snd_usb_pipe_sanity_check (dev,usb_sndctrlpipe (dev,0 ))) +if (usb_pipe_type_check (dev,usb_sndctrlpipe (dev,0 )))return -EINVAL ; ret = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), 1, USB_TYPE_VENDOR | USB_RECIP_DEVICE,
Signature · 1 line
2.28.0
Greg Kroah-Hartman
maintainerPATCH 2/10 USB: add usb_control_msg_send() and usb_control_msg_recv()
In reply to Greg Kroah-HartmanNew core functions to make sending/receiving USB control messages easier and saner.
In discussions, it turns out that the large majority of users of usb_control_msg() do so in potentially incorrect ways. The most common issue is where a "short" message is received, yet never detected properly due to "incorrect" error handling.
Handle all of this in the USB core with two new functions to try to make working with USB control messages simpler.
No more need for dynamic data, messages can be on the stack, and only "complete" send/receive will work without causing an error.
--- drivers/usb/core/message.c | 133 +++++++++++++++++++++++++++++++++++++ include/linux/usb.h | 6 ++ 2 files changed, 139 insertions(+)
drivers/usb/core/message.c +133 -0
@@ -162,6 +162,139 @@ int usb_control_msg(struct usb_device *dev, unsigned int pipe, __u8 request, }EXPORT_SYMBOL_GPL (usb_control_msg); +/** +* usb_control_msg_send - Builds a control "send" message, sends it off and waits for completion +* @dev: pointer to the usb device to send the message to +* @endpoint: endpoint to send the message to +* @request: USB message request value +* @requesttype: USB message request type value +* @value: USB message value +* @index: USB message index value +* @driver_data: pointer to the data to send +* @size: length in bytes of the data to send +* @timeout: time in msecs to wait for the message to complete before timing +* out (if 0 the wait is forever) +* +* Context: !in_interrupt () +* +* This function sends a control message to a specified endpoint that is not +* expected to fill in a response (i.e. a "send message") and waits for the +* message to complete, or timeout. +* +* Do not use this function from within an interrupt context. If you need +* an asynchronous message, or need to send a message from within interrupt +* context, use usb_submit_urb(). If a thread in your driver uses this call, +* make sure your disconnect() method can wait for it to complete. Since you +* don't have a handle on the URB used, you can't cancel the request. +* +* The data pointer can be made to a reference on the stack, or anywhere else, +* as it will not be modified at all. This does not have the restriction that +* usb_control_msg() has where the data pointer must be to dynamically allocated +* memory (i.e. memory that can be successfully DMAed to a device). +* +* Return: If successful, 0 is returned, Otherwise, a negative error number. +*/ +int usb_control_msg_send (struct usb_device *dev,__u8 endpoint,__u8 request, +__u8 requesttype,__u16 value,__u16 index, +const void *driver_data,__u16 size,int timeout) +{ +unsigned int pipe =usb_sndctrlpipe (dev, endpoint); +int ret; +u8 *data =NULL ; + +if (usb_pipe_type_check (dev, pipe)) +return -EINVAL ; + +if (size) { + data =kmemdup (driver_data, size,GFP_KERNEL ); +if (!data) +return -ENOMEM ; + } + + ret =usb_control_msg (dev, pipe, request, requesttype, value, index, + data, size, timeout); +kfree (data); + +if (ret <0 ) +return ret; +if (ret == size) +return 0 ; +return -EINVAL ; +} +EXPORT_SYMBOL_GPL (usb_control_msg_send); + +/** +* usb_control_msg_recv - Builds a control "receive" message, sends it off and waits for completion +* @dev: pointer to the usb device to send the message to +* @endpoint: endpoint to send the message to +* @request: USB message request value +* @requesttype: USB message request type value +* @value: USB message value +* @index: USB message index value +* @driver_data: pointer to the data to be filled in by the message +* @size: length in bytes of the data to be received +* @timeout: time in msecs to wait for the message to complete before timing +* out (if 0 the wait is forever) +* +* Context: !in_interrupt () +* +* This function sends a control message to a specified endpoint that is +* expected to fill in a response (i.e. a "receive message") and waits for the +* message to complete, or timeout. +* +* Do not use this function from within an interrupt context. If you need +* an asynchronous message, or need to send a message from within interrupt +* context, use usb_submit_urb(). If a thread in your driver uses this call, +* make sure your disconnect() method can wait for it to complete. Since you +* don't have a handle on the URB used, you can't cancel the request. +* +* The data pointer can be made to a reference on the stack, or anywhere else +* that can be successfully written to. This function does not have the +* restriction that usb_control_msg() has where the data pointer must be to +* dynamically allocated memory (i.e. memory that can be successfully DMAed to a +* device). +* +* The "whole" message must be properly received from the device in order for +* this function to be successful. If a device returns less than the expected +* amount of data, then the function will fail. Do not use this for messages +* where a variable amount of data might be returned. +* +* Return: If successful, 0 is returned, Otherwise, a negative error number. +*/ +int usb_control_msg_recv (struct usb_device *dev,__u8 endpoint,__u8 request, +__u8 requesttype,__u16 value,__u16 index, +void *driver_data,__u16 size,int timeout) +{ +unsigned int pipe =usb_rcvctrlpipe (dev, endpoint); +int ret; +u8 *data; + +if (!size || !driver_data ||usb_pipe_type_check (dev, pipe)) +return -EINVAL ; + + data =kmalloc (size,GFP_KERNEL ); +if (!data) +return -ENOMEM ; + + ret =usb_control_msg (dev, pipe, request, requesttype, value, index, + data, size, timeout); + +if (ret <0 ) + goto exit; + +if (ret == size) { +memcpy (driver_data, data, size); + ret =0 ; + }else { + ret = -EINVAL ; + } + +exit: +kfree (data); +return ret; +} +EXPORT_SYMBOL_GPL (usb_control_msg_recv); +/** * usb_interrupt_msg - Builds an interrupt urb, sends it off and waits for completion * @usb_dev: pointer to the usb device to send the message to
include/linux/usb.h +6 -0
@@ -1802,6 +1802,12 @@ extern int usb_bulk_msg(struct usb_device *usb_dev, unsigned int pipe, int timeout);/* wrappers around usb_control_msg() for the most common standard requests */ +int usb_control_msg_send (struct usb_device *dev,__u8 endpoint,__u8 request, +__u8 requesttype,__u16 value,__u16 index, +const void *data,__u16 size,int timeout); +int usb_control_msg_recv (struct usb_device *dev,__u8 endpoint,__u8 request, +__u8 requesttype,__u16 value,__u16 index, +void *data,__u16 size,int timeout);extern int usb_get_descriptor (struct usb_device *dev,unsigned char desctype,unsigned char descindex,void *buf,int size); extern int usb_get_status(struct usb_device *dev,
Signature · 1 line
2.28.0
Greg Kroah-Hartman
maintainerPATCH 7/10 sound: 6fire: move to use usb_control_msg_send() and usb_control_msg_recv()
In reply to Greg Kroah-HartmanThe usb_control_msg_send() and usb_control_msg_recv() calls can return an error if a "short" write/read happens, so move the driver over to using those calls instead, saving some logic in the wrapper functions that were being used in this driver.
This also resolves a long-staging bug where data on the stack was being sent in a USB control message, which was not allowed.
--- sound/usb/6fire/firmware.c | 38 +++++++++++++------------------------- 1 file changed, 13 insertions(+), 25 deletions(-)
sound/usb/6fire/firmware.c +13 -25
@@ -158,29 +158,17 @@ static int usb6fire_fw_ihex_init(const struct firmware *fw,static int usb6fire_fw_ezusb_write (struct usb_device *device,int type,int value,char *data,int len) { -int ret; - - ret =usb_control_msg (device,usb_sndctrlpipe (device,0 ), type, -USB_DIR_OUT |USB_TYPE_VENDOR |USB_RECIP_DEVICE , - value,0 , data, len,HZ ); -if (ret <0 ) -return ret; -else if (ret != len) -return -EIO ; -return 0 ; +return usb_control_msg_send (device,0 , type, +USB_DIR_OUT |USB_TYPE_VENDOR |USB_RECIP_DEVICE , + value,0 , data, len,HZ ); }static int usb6fire_fw_ezusb_read (struct usb_device *device,int type,int value,char *data,int len) { -int ret =usb_control_msg (device,usb_rcvctrlpipe (device,0 ), type, -USB_DIR_IN |USB_TYPE_VENDOR |USB_RECIP_DEVICE , value, -0 , data, len,HZ ); -if (ret <0 ) -return ret; -else if (ret != len) -return -EIO ; -return 0 ; +return usb_control_msg_recv (device,0 , type, +USB_DIR_IN |USB_TYPE_VENDOR |USB_RECIP_DEVICE , + value,0 , data, len,HZ ); } static int usb6fire_fw_fpga_write(struct usb_device *device,
@@ -230,7 +218,7 @@ static int usb6fire_fw_ezusb_upload(/* upload firmware image */ data =0x01 ;/* stop ezusb cpu */ ret =usb6fire_fw_ezusb_write (device,0xa0 ,0xe600 , &data,1 ); -if (ret <0 ) { +if (ret) {kfree (rec);release_firmware (fw); dev_err(&intf->dev,
@@ -242,7 +230,7 @@ static int usb6fire_fw_ezusb_upload(while (usb6fire_fw_ihex_next_record (rec)) {/* write firmware */ ret =usb6fire_fw_ezusb_write (device,0xa0 , rec->address, rec->data, rec->len); -if (ret <0 ) { +if (ret) {kfree (rec);release_firmware (fw); dev_err(&intf->dev,
@@ -257,7 +245,7 @@ static int usb6fire_fw_ezusb_upload(if (postdata) {/* write data after firmware has been uploaded */ ret =usb6fire_fw_ezusb_write (device,0xa0 , postaddr, postdata, postlen); -if (ret <0 ) { +if (ret) {dev_err (&intf->dev,"unable to upload ezusb firmware %s: post urb.\n" , fwname);
@@ -267,7 +255,7 @@ static int usb6fire_fw_ezusb_upload( data =0x00 ;/* resume ezusb cpu */ ret =usb6fire_fw_ezusb_write (device,0xa0 ,0xe600 , &data,1 ); -if (ret <0 ) { +if (ret) {dev_err (&intf->dev,"unable to upload ezusb firmware %s: end message.\n" , fwname);
@@ -302,7 +290,7 @@ static int usb6fire_fw_fpga_upload( end = fw->data + fw->size; ret =usb6fire_fw_ezusb_write (device,8 ,0 ,NULL ,0 ); -if (ret <0 ) { +if (ret) {kfree (buffer);release_firmware (fw); dev_err(&intf->dev,
@@ -327,7 +315,7 @@ static int usb6fire_fw_fpga_upload(kfree (buffer); ret =usb6fire_fw_ezusb_write (device,9 ,0 ,NULL ,0 ); -if (ret <0 ) { +if (ret) {dev_err (&intf->dev,"unable to upload fpga firmware: end urb.\n" );return ret;
@@ -363,7 +351,7 @@ int usb6fire_fw_init(struct usb_interface *intf)u8 buffer[12 ]; ret =usb6fire_fw_ezusb_read (device,1 ,0 , buffer,8 ); -if (ret <0 ) { +if (ret) {dev_err (&intf->dev,"unable to receive device firmware state.\n" );return ret;
Signature · 1 line
2.28.0
Greg Kroah-Hartman
maintainerPATCH 7/9 sound: line6: convert to use new usb control function...
In reply to Greg Kroah-Hartman--- sound/usb/line6/driver.c | 69 +++++++++++++++----------------------- sound/usb/line6/podhd.c | 17 ++++------ sound/usb/line6/toneport.c | 8 ++--- 3 files changed, 37 insertions(+), 57 deletions(-)
sound/usb/line6/driver.c +27 -42
@@ -337,23 +337,18 @@ int line6_read_data(struct usb_line6 *line6, unsigned address, void *data, {struct usb_device *usbdev = line6->usbdev;int ret; -unsigned char *len; +u8 len;unsigned count;if (address >0xffff || datalen >0xff )return -EINVAL ; - len =kmalloc (1 ,GFP_KERNEL ); -if (!len) -return -ENOMEM ; -/* query the serial number: */ - ret =usb_control_msg (usbdev,usb_sndctrlpipe (usbdev,0 ),0x67 , -USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_OUT , - (datalen <<8 ) |0x21 , address, -NULL ,0 ,LINE6_TIMEOUT *HZ ); - -if (ret <0 ) { + ret =usb_control_msg_send (usbdev,0 ,0x67 , +USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_OUT , + (datalen <<8 ) |0x21 , address,NULL ,0 , +LINE6_TIMEOUT *HZ ); +if (ret) {dev_err (line6->ifcdev,"read request failed (error %d)\n" , ret); goto exit; }
@@ -362,45 +357,41 @@ int line6_read_data(struct usb_line6 *line6, unsigned address, void *data,for (count =0 ; count <LINE6_READ_WRITE_MAX_RETRIES ; count++) {mdelay (LINE6_READ_WRITE_STATUS_DELAY ); - ret =usb_control_msg (usbdev,usb_rcvctrlpipe (usbdev,0 ),0x67 , -USB_TYPE_VENDOR |USB_RECIP_DEVICE | -USB_DIR_IN , -0x0012 ,0x0000 , len,1 , -LINE6_TIMEOUT *HZ ); -if (ret <0 ) { + ret =usb_control_msg_recv (usbdev,0 ,0x67 , +USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_IN , +0x0012 ,0x0000 , &len,1 , +LINE6_TIMEOUT *HZ ); +if (ret) {dev_err (line6->ifcdev,"receive length failed (error %d)\n" , ret); goto exit; } -if (*len !=0xff ) +if (len !=0xff )break ; } ret = -EIO ; -if (*len ==0xff ) { +if (len ==0xff ) {dev_err (line6->ifcdev,"read failed after %d retries\n" , count); goto exit; - }else if (*len != datalen) { + }else if (len != datalen) {/* should be equal or something went wrong */ dev_err (line6->ifcdev,"length mismatch (expected %d, got %d)\n" , - (int )datalen, (int )*len); + (int )datalen, len); goto exit; }/* receive the result: */ - ret =usb_control_msg (usbdev,usb_rcvctrlpipe (usbdev,0 ),0x67 , -USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_IN , -0x0013 ,0x0000 , data, datalen, -LINE6_TIMEOUT *HZ ); - -if (ret <0 ) + ret =usb_control_msg_recv (usbdev,0 ,0x67 , +USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_IN , +0x0013 ,0x0000 , data, datalen,LINE6_TIMEOUT *HZ ); +if (ret)dev_err (line6->ifcdev,"read failed (error %d)\n" , ret); exit: -kfree (len);return ret; }EXPORT_SYMBOL_GPL (line6_read_data);
@@ -423,12 +414,10 @@ int line6_write_data(struct usb_line6 *line6, unsigned address, void *data,if (!status)return -ENOMEM ; - ret =usb_control_msg (usbdev,usb_sndctrlpipe (usbdev,0 ),0x67 , -USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_OUT , -0x0022 , address, data, datalen, -LINE6_TIMEOUT *HZ ); - -if (ret <0 ) { + ret =usb_control_msg_send (usbdev,0 ,0x67 , +USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_OUT , +0x0022 , address, data, datalen,LINE6_TIMEOUT *HZ ); +if (ret) {dev_err (line6->ifcdev,"write request failed (error %d)\n" , ret); goto exit;
@@ -437,14 +426,10 @@ int line6_write_data(struct usb_line6 *line6, unsigned address, void *data,for (count =0 ; count <LINE6_READ_WRITE_MAX_RETRIES ; count++) {mdelay (LINE6_READ_WRITE_STATUS_DELAY ); - ret =usb_control_msg (usbdev,usb_rcvctrlpipe (usbdev,0 ), -0x67 , -USB_TYPE_VENDOR |USB_RECIP_DEVICE | -USB_DIR_IN , -0x0012 ,0x0000 , - status,1 ,LINE6_TIMEOUT *HZ ); - -if (ret <0 ) { + ret =usb_control_msg_recv (usbdev,0 ,0x67 , +USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_IN , +0x0012 ,0x0000 , status,1 ,LINE6_TIMEOUT *HZ ); +if (ret) {dev_err (line6->ifcdev,"receiving status failed (error %d)\n" , ret); goto exit;
sound/usb/line6/podhd.c +6 -11
@@ -183,29 +183,25 @@ static const struct attribute_group podhd_dev_attr_group = {static int podhd_dev_start (struct usb_line6_podhd *pod) {int ret; -u8 *init_bytes; +u8 init_bytes[8 ];int i;struct usb_device *usbdev = pod->line6.usbdev; - init_bytes =kmalloc (8 ,GFP_KERNEL ); -if (!init_bytes) -return -ENOMEM ; - - ret =usb_control_msg (usbdev,usb_sndctrlpipe (usbdev,0 ), + ret =usb_control_msg_send (usbdev,0 ,0x67 ,USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_OUT ,0x11 ,0 ,NULL ,0 ,LINE6_TIMEOUT *HZ ); -if (ret <0 ) { +if (ret) {dev_err (pod->line6.ifcdev,"read request failed (error %d)\n" , ret); goto exit; }/* NOTE: looks like some kind of ping message */ - ret =usb_control_msg (usbdev,usb_rcvctrlpipe (usbdev,0 ),0x67 , + ret =usb_control_msg_recv (usbdev,0 ,0x67 ,USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_IN ,0x11 ,0x0 , init_bytes,3 ,LINE6_TIMEOUT *HZ ); -if (ret <0 ) { +if (ret) {dev_err (pod->line6.ifcdev,"receive length failed (error %d)\n" , ret); goto exit;
@@ -220,13 +216,12 @@ static int podhd_dev_start(struct usb_line6_podhd *pod) goto exit; } - ret =usb_control_msg (usbdev,usb_sndctrlpipe (usbdev,0 ), + ret =usb_control_msg_send (usbdev,0 ,USB_REQ_SET_FEATURE ,USB_TYPE_STANDARD |USB_RECIP_DEVICE |USB_DIR_OUT ,1 ,0 ,NULL ,0 ,LINE6_TIMEOUT *HZ ); exit: -kfree (init_bytes);return ret; }
sound/usb/line6/toneport.c +4 -4
@@ -126,11 +126,11 @@ static int toneport_send_cmd(struct usb_device *usbdev, int cmd1, int cmd2) {int ret; - ret =usb_control_msg (usbdev,usb_sndctrlpipe (usbdev,0 ),0x67 , -USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_OUT , - cmd1, cmd2,NULL ,0 ,LINE6_TIMEOUT *HZ ); + ret =usb_control_msg_send (usbdev,0 ,0x67 , +USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_OUT , + cmd1, cmd2,NULL ,0 ,LINE6_TIMEOUT *HZ ); -if (ret <0 ) { +if (ret) {dev_err (&usbdev->dev,"send failed (error %d)\n" , ret);return ret; }
Signature · 1 line
2.28.0
Greg Kroah-Hartman
maintainerPATCH 6/10 sound: usx2y: move to use usb_control_msg_send()
In reply to Greg Kroah-HartmanThe usb_control_msg_send() call can handle data on the stack, as well as returning an error if a "short" write happens, so move the driver over to using that call instead. This ends up removing a helper function that is no longer needed.
--- sound/usb/usx2y/us122l.c | 42 ++++++++-------------------------------- 1 file changed, 8 insertions(+), 34 deletions(-)
sound/usb/usx2y/us122l.c +8 -34
@@ -82,40 +82,13 @@ static int us144_create_usbmidi(struct snd_card *card) &US122L(card)->midi_list, &quirk); } -/* -* Wrapper for usb_control_msg(). -* Allocates a temp buffer to prevent dmaing from/to the stack. -*/ -static int us122l_ctl_msg (struct usb_device *dev,unsigned int pipe, -__u8 request,__u8 requesttype, -__u16 value,__u16 index,void *data, -__u16 size,int timeout) -{ -int err; -void *buf =NULL ; - -if (size >0 ) { - buf =kmemdup (data, size,GFP_KERNEL ); -if (!buf) -return -ENOMEM ; - } - err =usb_control_msg (dev, pipe, request, requesttype, - value, index, buf, size, timeout); -if (size >0 ) { -memcpy (data, buf, size); -kfree (buf); - } -return err; -} -static void pt_info_set (struct usb_device *dev,u8 v) {int ret; - ret =usb_control_msg (dev,usb_sndctrlpipe (dev,0 ), -'I' , -USB_DIR_OUT |USB_TYPE_VENDOR |USB_RECIP_DEVICE , - v,0 ,NULL ,0 ,1000 ); + ret =usb_control_msg_send (dev,0 ,'I' , +USB_DIR_OUT |USB_TYPE_VENDOR |USB_RECIP_DEVICE , + v,0 ,NULL ,0 ,1000 );snd_printdd (KERN_DEBUG "%i\n" , ret); }
@@ -305,10 +278,11 @@ static int us122l_set_sample_rate(struct usb_device *dev, int rate) data[0 ] = rate; data[1 ] = rate >>8 ; data[2 ] = rate >>16 ; - err =us122l_ctl_msg (dev,usb_sndctrlpipe (dev,0 ),UAC_SET_CUR , -USB_TYPE_CLASS |USB_RECIP_ENDPOINT |USB_DIR_OUT , -UAC_EP_CS_ATTR_SAMPLE_RATE <<8 , ep, data,3 ,1000 ); -if (err <0 ) + err =usb_control_msg_send (dev,0 ,UAC_SET_CUR , +USB_TYPE_CLASS |USB_RECIP_ENDPOINT |USB_DIR_OUT , +UAC_EP_CS_ATTR_SAMPLE_RATE <<8 , ep, data,3 , +1000 ); +if (err)snd_printk (KERN_ERR "%d: cannot set freq %d to ep 0x%x\n" , dev->devnum, rate, ep);return err;
Signature · 1 line
2.28.0
Greg Kroah-Hartman
maintainerPATCH 8/9 sound: 6fire: move to use new usb control functions...
In reply to Greg Kroah-Hartman--- sound/usb/6fire/firmware.c | 16 ++-------------- 1 file changed, 2 insertions(+), 14 deletions(-)
sound/usb/6fire/firmware.c +2 -14
@@ -158,29 +158,17 @@ static int usb6fire_fw_ihex_init(const struct firmware *fw,static int usb6fire_fw_ezusb_write (struct usb_device *device,int type,int value,char *data,int len) { -int ret; - - ret =usb_control_msg (device,usb_sndctrlpipe (device,0 ), type, +return usb_control_msg_send (device,0 , type,USB_DIR_OUT |USB_TYPE_VENDOR |USB_RECIP_DEVICE , value,0 , data, len,HZ ); -if (ret <0 ) -return ret; -else if (ret != len) -return -EIO ; -return 0 ; }static int usb6fire_fw_ezusb_read (struct usb_device *device,int type,int value,char *data,int len) { -int ret =usb_control_msg (device,usb_rcvctrlpipe (device,0 ), type, +return usb_control_msg_recv (device,0 , type,USB_DIR_IN |USB_TYPE_VENDOR |USB_RECIP_DEVICE , value,0 , data, len,HZ ); -if (ret <0 ) -return ret; -else if (ret != len) -return -EIO ; -return 0 ; } static int usb6fire_fw_fpga_write(struct usb_device *device,
Signature · 1 line
2.28.0
Greg Kroah-Hartman
maintainerPATCH 5/10 USB: legousbtower: use usb_control_msg_recv()
In reply to Greg Kroah-HartmanThe usb_control_msg_recv() function can handle data on the stack, as well as properly detecting short reads, so move to use that function instead of the older usb_control_msg() call. This ends up removing a lot of extra lines in the driver.
--- drivers/usb/misc/legousbtower.c | 60 +++++++++++---------------------- 1 file changed, 19 insertions(+), 41 deletions(-)
drivers/usb/misc/legousbtower.c +19 -41
@@ -308,15 +308,9 @@ static int tower_open(struct inode *inode, struct file *file)int subminor;int retval =0 ;struct usb_interface *interface; -struct tower_reset_reply *reset_reply; +struct tower_reset_reply reset_reply;int result; - reset_reply =kmalloc (sizeof (*reset_reply),GFP_KERNEL ); -if (!reset_reply) { - retval = -ENOMEM ; - goto exit; - } -nonseekable_open (inode, file); subminor =iminor (inode);
@@ -347,15 +341,11 @@ static int tower_open(struct inode *inode, struct file *file) }/* reset the tower */ - result =usb_control_msg (dev->udev, -usb_rcvctrlpipe (dev->udev,0 ), -LEGO_USB_TOWER_REQUEST_RESET , -USB_TYPE_VENDOR |USB_DIR_IN |USB_RECIP_DEVICE , -0 , -0 , - reset_reply, -sizeof (*reset_reply), -1000 ); + result =usb_control_msg_recv (dev->udev,0 , +LEGO_USB_TOWER_REQUEST_RESET , +USB_TYPE_VENDOR |USB_DIR_IN |USB_RECIP_DEVICE , +0 ,0 , + &reset_reply,sizeof (reset_reply),1000 );if (result <0 ) {dev_err (&dev->udev->dev,"LEGO USB Tower reset control request failed\n" );
@@ -394,7 +384,6 @@ static int tower_open(struct inode *inode, struct file *file)mutex_unlock (&dev->lock); exit: -kfree (reset_reply);return retval; }
@@ -753,7 +742,7 @@ static int tower_probe(struct usb_interface *interface, const struct usb_device_struct device *idev = &interface->dev;struct usb_device *udev =interface_to_usbdev (interface);struct lego_usb_tower *dev; -struct tower_get_version_reply *get_version_reply =NULL ; +struct tower_get_version_reply get_version_reply;int retval = -ENOMEM ;int result;
@@ -798,34 +787,25 @@ static int tower_probe(struct usb_interface *interface, const struct usb_device_ dev->interrupt_in_interval = interrupt_in_interval ? interrupt_in_interval : dev->interrupt_in_endpoint->bInterval; dev->interrupt_out_interval = interrupt_out_interval ? interrupt_out_interval : dev->interrupt_out_endpoint->bInterval; - get_version_reply =kmalloc (sizeof (*get_version_reply),GFP_KERNEL ); -if (!get_version_reply) { - retval = -ENOMEM ; - goto error; - } -/* get the firmware version and log it */ - result =usb_control_msg (udev, -usb_rcvctrlpipe (udev,0 ), -LEGO_USB_TOWER_REQUEST_GET_VERSION , -USB_TYPE_VENDOR |USB_DIR_IN |USB_RECIP_DEVICE , -0 , -0 , - get_version_reply, -sizeof (*get_version_reply), -1000 ); -if (result !=sizeof (*get_version_reply)) { -if (result >=0 ) - result = -EIO ; + result =usb_control_msg_recv (udev,0 , +LEGO_USB_TOWER_REQUEST_GET_VERSION , +USB_TYPE_VENDOR |USB_DIR_IN |USB_RECIP_DEVICE , +0 , +0 , + &get_version_reply, +sizeof (get_version_reply), +1000 ); +if (!result) {dev_err (idev,"get version request failed: %d\n" , result); retval = result; goto error; }dev_info (&interface->dev,"LEGO USB Tower firmware version is %d.%d build %d\n" , - get_version_reply->major, - get_version_reply->minor, -le16_to_cpu (get_version_reply->build_no)); + get_version_reply.major, + get_version_reply.minor, +le16_to_cpu (get_version_reply.build_no));/* we can register the device now, as it is ready */ usb_set_intfdata (interface, dev);
@@ -844,11 +824,9 @@ static int tower_probe(struct usb_interface *interface, const struct usb_device_ USB_MAJOR, dev->minor); exit: -kfree (get_version_reply);return retval; error: -kfree (get_version_reply);tower_delete (dev);return retval; }
Signature · 1 line
2.28.0
Greg Kroah-Hartman
maintainerPATCH 4/10 USB: core: hub.c: use usb_control_msg_send() in a few places
In reply to Greg Kroah-HartmanThere are a few calls to usb_control_msg() that can be converted to use usb_control_msg_send() instead, so do that in order to make the error checking a bit simpler and the code smaller.
--- drivers/usb/core/hub.c | 128 +++++++++++++++-------------------------- 1 file changed, 47 insertions(+), 81 deletions(-)
drivers/usb/core/hub.c +47 -81
@@ -410,8 +410,8 @@ static int get_hub_descriptor(struct usb_device *hdev,*/ static int clear_hub_feature (struct usb_device *hdev,int feature) { -return usb_control_msg (hdev,usb_sndctrlpipe (hdev,0 ), -USB_REQ_CLEAR_FEATURE ,USB_RT_HUB , feature,0 ,NULL ,0 ,1000 ); +return usb_control_msg_send (hdev,0 ,USB_REQ_CLEAR_FEATURE ,USB_RT_HUB , + feature,0 ,NULL ,0 ,1000 ); }/*
@@ -419,9 +419,8 @@ static int clear_hub_feature(struct usb_device *hdev, int feature)*/ int usb_clear_port_feature (struct usb_device *hdev,int port1,int feature) { -return usb_control_msg (hdev,usb_sndctrlpipe (hdev,0 ), -USB_REQ_CLEAR_FEATURE ,USB_RT_PORT , feature, port1, -NULL ,0 ,1000 ); +return usb_control_msg_send (hdev,0 ,USB_REQ_CLEAR_FEATURE ,USB_RT_PORT , + feature, port1,NULL ,0 ,1000 ); }/*
@@ -429,9 +428,8 @@ int usb_clear_port_feature(struct usb_device *hdev, int port1, int feature)*/ static int set_port_feature (struct usb_device *hdev,int port1,int feature) { -return usb_control_msg (hdev,usb_sndctrlpipe (hdev,0 ), -USB_REQ_SET_FEATURE ,USB_RT_PORT , feature, port1, -NULL ,0 ,1000 ); +return usb_control_msg_send (hdev,0 ,USB_REQ_SET_FEATURE ,USB_RT_PORT , + feature, port1,NULL ,0 ,1000 ); }static char *to_led_name (int selector)
@@ -755,15 +753,14 @@ hub_clear_tt_buffer(struct usb_device *hdev, u16 devinfo, u16 tt)/* Need to clear both directions for control ep */ if (((devinfo >>11 ) &USB_ENDPOINT_XFERTYPE_MASK ) ==USB_ENDPOINT_XFER_CONTROL ) { -int status =usb_control_msg (hdev,usb_sndctrlpipe (hdev,0 ), -HUB_CLEAR_TT_BUFFER ,USB_RT_PORT , - devinfo ^0x8000 , tt,NULL ,0 ,1000 ); +int status =usb_control_msg_send (hdev,0 , +HUB_CLEAR_TT_BUFFER ,USB_RT_PORT , + devinfo ^0x8000 , tt,NULL ,0 ,1000 );if (status)return status; } -return usb_control_msg (hdev,usb_sndctrlpipe (hdev,0 ), -HUB_CLEAR_TT_BUFFER ,USB_RT_PORT , devinfo, - tt,NULL ,0 ,1000 ); +return usb_control_msg_send (hdev,0 ,HUB_CLEAR_TT_BUFFER ,USB_RT_PORT , + devinfo, tt,NULL ,0 ,1000 ); }/*
@@ -1049,11 +1046,10 @@ static void hub_activate(struct usb_hub *hub, enum hub_activation_type type)*/ if (type !=HUB_RESUME ) {if (hdev->parent &&hub_is_superspeed (hdev)) { - ret =usb_control_msg (hdev,usb_sndctrlpipe (hdev,0 ), -HUB_SET_DEPTH ,USB_RT_HUB , - hdev->level -1 ,0 ,NULL ,0 , -USB_CTRL_SET_TIMEOUT ); -if (ret <0 ) + ret =usb_control_msg_send (hdev,0 ,HUB_SET_DEPTH ,USB_RT_HUB , + hdev->level -1 ,0 ,NULL ,0 , +USB_CTRL_SET_TIMEOUT ); +if (ret)dev_err (hub->intfdev,"set hub depth failed\n" ); }
@@ -2329,13 +2325,10 @@ static int usb_enumerate_device_otg(struct usb_device *udev)/* enable HNP before suspend, it's simpler */ if (port1 == bus->otg_port) { bus->b_hnp_enable =1 ; - err =usb_control_msg (udev, -usb_sndctrlpipe (udev,0 ), -USB_REQ_SET_FEATURE ,0 , -USB_DEVICE_B_HNP_ENABLE , -0 ,NULL ,0 , -USB_CTRL_SET_TIMEOUT ); -if (err <0 ) { + err =usb_control_msg_send (udev,0 ,USB_REQ_SET_FEATURE ,0 , +USB_DEVICE_B_HNP_ENABLE ,0 , +NULL ,0 ,USB_CTRL_SET_TIMEOUT ); +if (err) {/* * OTG MESSAGE: report errors here, * customize to match your product.
@@ -2347,13 +2340,10 @@ static int usb_enumerate_device_otg(struct usb_device *udev) }else if (desc->bLength ==sizeof (struct usb_otg_descriptor )) {/* Set a_alt_hnp_support for legacy otg device */ - err =usb_control_msg (udev, -usb_sndctrlpipe (udev,0 ), -USB_REQ_SET_FEATURE ,0 , -USB_DEVICE_A_ALT_HNP_SUPPORT , -0 ,NULL ,0 , -USB_CTRL_SET_TIMEOUT ); -if (err <0 ) + err =usb_control_msg_send (udev,0 ,USB_REQ_SET_FEATURE ,0 , +USB_DEVICE_A_ALT_HNP_SUPPORT ,0 , +NULL ,0 ,USB_CTRL_SET_TIMEOUT ); +if (err)dev_err (&udev->dev,"set a_alt_hnp_support failed: %d\n" , err);
@@ -3121,10 +3111,8 @@ int usb_disable_ltm(struct usb_device *udev)if (!udev->actconfig)return 0 ; -return usb_control_msg (udev,usb_sndctrlpipe (udev,0 ), -USB_REQ_CLEAR_FEATURE ,USB_RECIP_DEVICE , -USB_DEVICE_LTM_ENABLE ,0 ,NULL ,0 , -USB_CTRL_SET_TIMEOUT ); +return usb_control_msg_send (udev,0 ,USB_REQ_CLEAR_FEATURE ,USB_RECIP_DEVICE , +USB_DEVICE_LTM_ENABLE ,0 ,NULL ,0 ,USB_CTRL_SET_TIMEOUT ); }EXPORT_SYMBOL_GPL (usb_disable_ltm);
@@ -3143,10 +3131,8 @@ void usb_enable_ltm(struct usb_device *udev)if (!udev->actconfig)return ; -usb_control_msg (udev,usb_sndctrlpipe (udev,0 ), -USB_REQ_SET_FEATURE ,USB_RECIP_DEVICE , -USB_DEVICE_LTM_ENABLE ,0 ,NULL ,0 , -USB_CTRL_SET_TIMEOUT ); +usb_control_msg_send (udev,0 ,USB_REQ_SET_FEATURE ,USB_RECIP_DEVICE , +USB_DEVICE_LTM_ENABLE ,0 ,NULL ,0 ,USB_CTRL_SET_TIMEOUT ); }EXPORT_SYMBOL_GPL (usb_enable_ltm);
@@ -3163,17 +3149,14 @@ EXPORT_SYMBOL_GPL(usb_enable_ltm);static int usb_enable_remote_wakeup (struct usb_device *udev) {if (udev->speed <USB_SPEED_SUPER ) -return usb_control_msg (udev,usb_sndctrlpipe (udev,0 ), -USB_REQ_SET_FEATURE ,USB_RECIP_DEVICE , -USB_DEVICE_REMOTE_WAKEUP ,0 ,NULL ,0 , -USB_CTRL_SET_TIMEOUT ); +return usb_control_msg_send (udev,0 ,USB_REQ_SET_FEATURE ,USB_RECIP_DEVICE , +USB_DEVICE_REMOTE_WAKEUP ,0 , +NULL ,0 ,USB_CTRL_SET_TIMEOUT );else -return usb_control_msg (udev,usb_sndctrlpipe (udev,0 ), -USB_REQ_SET_FEATURE ,USB_RECIP_INTERFACE , -USB_INTRF_FUNC_SUSPEND , -USB_INTRF_FUNC_SUSPEND_RW | -USB_INTRF_FUNC_SUSPEND_LP , -NULL ,0 ,USB_CTRL_SET_TIMEOUT ); +return usb_control_msg_send (udev,0 ,USB_REQ_SET_FEATURE ,USB_RECIP_INTERFACE , +USB_INTRF_FUNC_SUSPEND , +USB_INTRF_FUNC_SUSPEND_RW |USB_INTRF_FUNC_SUSPEND_LP , +NULL ,0 ,USB_CTRL_SET_TIMEOUT ); }/*
@@ -3189,15 +3172,11 @@ static int usb_enable_remote_wakeup(struct usb_device *udev)static int usb_disable_remote_wakeup (struct usb_device *udev) {if (udev->speed <USB_SPEED_SUPER ) -return usb_control_msg (udev,usb_sndctrlpipe (udev,0 ), -USB_REQ_CLEAR_FEATURE ,USB_RECIP_DEVICE , -USB_DEVICE_REMOTE_WAKEUP ,0 ,NULL ,0 , -USB_CTRL_SET_TIMEOUT ); +return usb_control_msg_send (udev,0 ,USB_REQ_CLEAR_FEATURE ,USB_RECIP_DEVICE , +USB_DEVICE_REMOTE_WAKEUP ,0 ,NULL ,0 ,USB_CTRL_SET_TIMEOUT );else -return usb_control_msg (udev,usb_sndctrlpipe (udev,0 ), -USB_REQ_SET_FEATURE ,USB_RECIP_INTERFACE , -USB_INTRF_FUNC_SUSPEND ,0 ,NULL ,0 , -USB_CTRL_SET_TIMEOUT ); +return usb_control_msg_send (udev,0 ,USB_REQ_SET_FEATURE ,USB_RECIP_INTERFACE , +USB_INTRF_FUNC_SUSPEND ,0 ,NULL ,0 ,USB_CTRL_SET_TIMEOUT ); }/* Count of wakeup-enabled devices at or below udev */
@@ -3844,7 +3823,7 @@ static const char * const usb3_lpm_names[] = {*/ static int usb_req_set_sel (struct usb_device *udev,enum usb3_link_state state) { -struct usb_set_sel_req *sel_values; +struct usb_set_sel_req sel_values;unsigned long long u1_sel;unsigned long long u1_pel;unsigned long long u2_sel;
@@ -3896,27 +3875,14 @@ static int usb_req_set_sel(struct usb_device *udev, enum usb3_link_state state)if (u2_pel >USB3_LPM_MAX_U2_SEL_PEL ) u2_pel =USB3_LPM_MAX_U2_SEL_PEL ; -/* -* usb_enable_lpm() can be called as part of a failed device reset, -* which may be initiated by an error path of a mass storage driver. -* Therefore, use GFP_NOIO. -*/ - sel_values =kmalloc (sizeof *(sel_values),GFP_NOIO ); -if (!sel_values) -return -ENOMEM ; - - sel_values->u1_sel = u1_sel; - sel_values->u1_pel = u1_pel; - sel_values->u2_sel =cpu_to_le16 (u2_sel); - sel_values->u2_pel =cpu_to_le16 (u2_pel); + sel_values.u1_sel = u1_sel; + sel_values.u1_pel = u1_pel; + sel_values.u2_sel =cpu_to_le16 (u2_sel); + sel_values.u2_pel =cpu_to_le16 (u2_pel); - ret =usb_control_msg (udev,usb_sndctrlpipe (udev,0 ), -USB_REQ_SET_SEL , -USB_RECIP_DEVICE , -0 ,0 , - sel_values,sizeof *(sel_values), -USB_CTRL_SET_TIMEOUT ); -kfree (sel_values); + ret =usb_control_msg_send (udev,0 ,USB_REQ_SET_SEL ,USB_RECIP_DEVICE , +0 ,0 , &sel_values,sizeof (sel_values), +USB_CTRL_SET_TIMEOUT );return ret; }
@@ -4056,7 +4022,7 @@ static void usb_enable_link_state(struct usb_hcd *hcd, struct usb_device *udev,* associated with the link state we're about to enable. */ ret =usb_req_set_sel (udev, state); -if (ret <0 ) { +if (ret) {dev_warn (&udev->dev,"Set SEL for device-initiated %s failed.\n" , usb3_lpm_names[state]);return ;
Signature · 1 line
2.28.0
Greg Kroah-Hartman
maintainerPATCH 3/10 USB: core: message.c: use usb_control_msg_send() in a few places
In reply to Greg Kroah-HartmanThere are a few calls to usb_control_msg() that can be converted to use usb_control_msg_send() instead, so do that in order to make the error checking a bit simpler.
--- drivers/usb/core/message.c | 38 +++++++++++++++++++------------------- 1 file changed, 19 insertions(+), 19 deletions(-)
drivers/usb/core/message.c +19 -19
@@ -1081,7 +1081,7 @@ int usb_set_isoch_delay(struct usb_device *dev)if (dev->speed <USB_SPEED_SUPER )return 0 ; - return usb_control_msg(dev, usb_sndctrlpipe(dev, 0), + return usb_control_msg_send(dev, 0, USB_REQ_SET_ISOCH_DELAY, USB_DIR_OUT | USB_TYPE_STANDARD | USB_RECIP_DEVICE, dev->hub_delay, 0, NULL, 0,
@@ -1203,13 +1203,13 @@ int usb_clear_halt(struct usb_device *dev, int pipe)* (like some ibmcam model 1 units) seem to expect hosts to make * this request for iso endpoints, which can't halt! */ - result =usb_control_msg (dev,usb_sndctrlpipe (dev,0 ), -USB_REQ_CLEAR_FEATURE ,USB_RECIP_ENDPOINT , -USB_ENDPOINT_HALT , endp,NULL ,0 , -USB_CTRL_SET_TIMEOUT ); + result =usb_control_msg_send (dev,0 , +USB_REQ_CLEAR_FEATURE ,USB_RECIP_ENDPOINT , +USB_ENDPOINT_HALT , endp,NULL ,0 , +USB_CTRL_SET_TIMEOUT );/* don't un-halt or force to DATA0 except on success */ -if (result <0 ) +if (result)return result;/* NOTE: seems like Microsoft and Apple don't bother verifying
@@ -1558,9 +1558,10 @@ int usb_set_interface(struct usb_device *dev, int interface, int alternate)if (dev->quirks &USB_QUIRK_NO_SET_INTF ) ret = -EPIPE ;else - ret =usb_control_msg (dev,usb_sndctrlpipe (dev,0 ), -USB_REQ_SET_INTERFACE ,USB_RECIP_INTERFACE , - alternate, interface,NULL ,0 ,5000 ); + ret =usb_control_msg_send (dev,0 , +USB_REQ_SET_INTERFACE , +USB_RECIP_INTERFACE , alternate, + interface,NULL ,0 ,5000 );/* 9.4.10 says devices don't need this and are free to STALL the * request if the interface only has one alternate setting.
@@ -1570,7 +1571,7 @@ int usb_set_interface(struct usb_device *dev, int interface, int alternate)"manual set_interface for iface %d, alt %d\n" , interface, alternate); manual =1 ; - }else if (ret <0 ) { + }else if (ret) {/* Re-instate the old alt setting */ usb_hcd_alloc_bandwidth (dev,NULL , alt, iface->cur_altsetting);usb_enable_lpm (dev);
@@ -1718,11 +1719,10 @@ int usb_reset_configuration(struct usb_device *dev)mutex_unlock (hcd->bandwidth_mutex);return retval; } - retval =usb_control_msg (dev,usb_sndctrlpipe (dev,0 ), -USB_REQ_SET_CONFIGURATION ,0 , - config->desc.bConfigurationValue,0 , -NULL ,0 ,USB_CTRL_SET_TIMEOUT ); -if (retval <0 ) + retval =usb_control_msg_send (dev,0 ,USB_REQ_SET_CONFIGURATION ,0 , + config->desc.bConfigurationValue,0 , +NULL ,0 ,USB_CTRL_SET_TIMEOUT ); +if (retval) goto reset_old_alts;mutex_unlock (hcd->bandwidth_mutex);
@@ -2103,10 +2103,10 @@ int usb_set_configuration(struct usb_device *dev, int configuration) }kfree (new_interfaces); - ret =usb_control_msg (dev,usb_sndctrlpipe (dev,0 ), -USB_REQ_SET_CONFIGURATION ,0 , configuration,0 , -NULL ,0 ,USB_CTRL_SET_TIMEOUT ); -if (ret <0 && cp) { + ret =usb_control_msg_send (dev,0 ,USB_REQ_SET_CONFIGURATION ,0 , + configuration,0 ,NULL ,0 , +USB_CTRL_SET_TIMEOUT ); +if (ret && cp) {/* * All the old state is gone, so what else can we do? * The device is probably useless now anyway.
Signature · 1 line
2.28.0
Greg Kroah-Hartman
maintainerPATCH 8/10 sound: line6: move to use usb_control_msg_send() and usb_control_msg_recv()
In reply to Greg Kroah-HartmanThe usb_control_msg_send() and usb_control_msg_recv() calls can return an error if a "short" write/read happens, and they can handle data off of the stack, so move the driver over to using those calls instead, saving some logic when dynamically allocating memory.
--- sound/usb/line6/driver.c | 69 +++++++++++++++----------------------- sound/usb/line6/podhd.c | 17 ++++------ sound/usb/line6/toneport.c | 8 ++--- 3 files changed, 37 insertions(+), 57 deletions(-)
sound/usb/line6/driver.c +27 -42
@@ -337,23 +337,18 @@ int line6_read_data(struct usb_line6 *line6, unsigned address, void *data, {struct usb_device *usbdev = line6->usbdev;int ret; -unsigned char *len; +u8 len;unsigned count;if (address >0xffff || datalen >0xff )return -EINVAL ; - len =kmalloc (1 ,GFP_KERNEL ); -if (!len) -return -ENOMEM ; -/* query the serial number: */ - ret =usb_control_msg (usbdev,usb_sndctrlpipe (usbdev,0 ),0x67 , -USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_OUT , - (datalen <<8 ) |0x21 , address, -NULL ,0 ,LINE6_TIMEOUT *HZ ); - -if (ret <0 ) { + ret =usb_control_msg_send (usbdev,0 ,0x67 , +USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_OUT , + (datalen <<8 ) |0x21 , address,NULL ,0 , +LINE6_TIMEOUT *HZ ); +if (ret) {dev_err (line6->ifcdev,"read request failed (error %d)\n" , ret); goto exit; }
@@ -362,45 +357,41 @@ int line6_read_data(struct usb_line6 *line6, unsigned address, void *data,for (count =0 ; count <LINE6_READ_WRITE_MAX_RETRIES ; count++) {mdelay (LINE6_READ_WRITE_STATUS_DELAY ); - ret =usb_control_msg (usbdev,usb_rcvctrlpipe (usbdev,0 ),0x67 , -USB_TYPE_VENDOR |USB_RECIP_DEVICE | -USB_DIR_IN , -0x0012 ,0x0000 , len,1 , -LINE6_TIMEOUT *HZ ); -if (ret <0 ) { + ret =usb_control_msg_recv (usbdev,0 ,0x67 , +USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_IN , +0x0012 ,0x0000 , &len,1 , +LINE6_TIMEOUT *HZ ); +if (ret) {dev_err (line6->ifcdev,"receive length failed (error %d)\n" , ret); goto exit; } -if (*len !=0xff ) +if (len !=0xff )break ; } ret = -EIO ; -if (*len ==0xff ) { +if (len ==0xff ) {dev_err (line6->ifcdev,"read failed after %d retries\n" , count); goto exit; - }else if (*len != datalen) { + }else if (len != datalen) {/* should be equal or something went wrong */ dev_err (line6->ifcdev,"length mismatch (expected %d, got %d)\n" , - (int )datalen, (int )*len); + (int )datalen, len); goto exit; }/* receive the result: */ - ret =usb_control_msg (usbdev,usb_rcvctrlpipe (usbdev,0 ),0x67 , -USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_IN , -0x0013 ,0x0000 , data, datalen, -LINE6_TIMEOUT *HZ ); - -if (ret <0 ) + ret =usb_control_msg_recv (usbdev,0 ,0x67 , +USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_IN , +0x0013 ,0x0000 , data, datalen,LINE6_TIMEOUT *HZ ); +if (ret)dev_err (line6->ifcdev,"read failed (error %d)\n" , ret); exit: -kfree (len);return ret; }EXPORT_SYMBOL_GPL (line6_read_data);
@@ -423,12 +414,10 @@ int line6_write_data(struct usb_line6 *line6, unsigned address, void *data,if (!status)return -ENOMEM ; - ret =usb_control_msg (usbdev,usb_sndctrlpipe (usbdev,0 ),0x67 , -USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_OUT , -0x0022 , address, data, datalen, -LINE6_TIMEOUT *HZ ); - -if (ret <0 ) { + ret =usb_control_msg_send (usbdev,0 ,0x67 , +USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_OUT , +0x0022 , address, data, datalen,LINE6_TIMEOUT *HZ ); +if (ret) {dev_err (line6->ifcdev,"write request failed (error %d)\n" , ret); goto exit;
@@ -437,14 +426,10 @@ int line6_write_data(struct usb_line6 *line6, unsigned address, void *data,for (count =0 ; count <LINE6_READ_WRITE_MAX_RETRIES ; count++) {mdelay (LINE6_READ_WRITE_STATUS_DELAY ); - ret =usb_control_msg (usbdev,usb_rcvctrlpipe (usbdev,0 ), -0x67 , -USB_TYPE_VENDOR |USB_RECIP_DEVICE | -USB_DIR_IN , -0x0012 ,0x0000 , - status,1 ,LINE6_TIMEOUT *HZ ); - -if (ret <0 ) { + ret =usb_control_msg_recv (usbdev,0 ,0x67 , +USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_IN , +0x0012 ,0x0000 , status,1 ,LINE6_TIMEOUT *HZ ); +if (ret) {dev_err (line6->ifcdev,"receiving status failed (error %d)\n" , ret); goto exit;
sound/usb/line6/podhd.c +6 -11
@@ -183,29 +183,25 @@ static const struct attribute_group podhd_dev_attr_group = {static int podhd_dev_start (struct usb_line6_podhd *pod) {int ret; -u8 *init_bytes; +u8 init_bytes[8 ];int i;struct usb_device *usbdev = pod->line6.usbdev; - init_bytes =kmalloc (8 ,GFP_KERNEL ); -if (!init_bytes) -return -ENOMEM ; - - ret =usb_control_msg (usbdev,usb_sndctrlpipe (usbdev,0 ), + ret =usb_control_msg_send (usbdev,0 ,0x67 ,USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_OUT ,0x11 ,0 ,NULL ,0 ,LINE6_TIMEOUT *HZ ); -if (ret <0 ) { +if (ret) {dev_err (pod->line6.ifcdev,"read request failed (error %d)\n" , ret); goto exit; }/* NOTE: looks like some kind of ping message */ - ret =usb_control_msg (usbdev,usb_rcvctrlpipe (usbdev,0 ),0x67 , + ret =usb_control_msg_recv (usbdev,0 ,0x67 ,USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_IN ,0x11 ,0x0 , init_bytes,3 ,LINE6_TIMEOUT *HZ ); -if (ret <0 ) { +if (ret) {dev_err (pod->line6.ifcdev,"receive length failed (error %d)\n" , ret); goto exit;
@@ -220,13 +216,12 @@ static int podhd_dev_start(struct usb_line6_podhd *pod) goto exit; } - ret =usb_control_msg (usbdev,usb_sndctrlpipe (usbdev,0 ), + ret =usb_control_msg_send (usbdev,0 ,USB_REQ_SET_FEATURE ,USB_TYPE_STANDARD |USB_RECIP_DEVICE |USB_DIR_OUT ,1 ,0 ,NULL ,0 ,LINE6_TIMEOUT *HZ ); exit: -kfree (init_bytes);return ret; }
sound/usb/line6/toneport.c +4 -4
@@ -126,11 +126,11 @@ static int toneport_send_cmd(struct usb_device *usbdev, int cmd1, int cmd2) {int ret; - ret =usb_control_msg (usbdev,usb_sndctrlpipe (usbdev,0 ),0x67 , -USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_OUT , - cmd1, cmd2,NULL ,0 ,LINE6_TIMEOUT *HZ ); + ret =usb_control_msg_send (usbdev,0 ,0x67 , +USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_OUT , + cmd1, cmd2,NULL ,0 ,LINE6_TIMEOUT *HZ ); -if (ret <0 ) { +if (ret) {dev_err (&usbdev->dev,"send failed (error %d)\n" , ret);return ret; }
Signature · 1 line
2.28.0
Greg Kroah-Hartman
maintainerPATCH 9/10 sound: hiface: move to use usb_control_msg_send()
In reply to Greg Kroah-HartmanThe usb_control_msg_send() call can return an error if a "short" write happens, so move the driver over to using that call instead.
--- sound/usb/hiface/pcm.c | 14 ++++++-------- 1 file changed, 6 insertions(+), 8 deletions(-)
sound/usb/hiface/pcm.c +6 -8
@@ -156,16 +156,14 @@ static int hiface_pcm_set_rate(struct pcm_runtime *rt, unsigned int rate)* This control message doesn't have any ack from the * other side */ - ret =usb_control_msg (device,usb_sndctrlpipe (device,0 ), -HIFACE_SET_RATE_REQUEST , -USB_DIR_OUT |USB_TYPE_VENDOR |USB_RECIP_OTHER , - rate_value,0 ,NULL ,0 ,100 ); -if (ret <0 ) { + ret =usb_control_msg_send (device,0 , +HIFACE_SET_RATE_REQUEST , +USB_DIR_OUT |USB_TYPE_VENDOR |USB_RECIP_OTHER , + rate_value,0 ,NULL ,0 ,100 ); +if (ret)dev_err (&device->dev,"Error setting samplerate %d.\n" , rate); -return ret; - } -return 0 ; +return ret; } static struct pcm_substream *hiface_pcm_get_substream(struct snd_pcm_substream
Signature · 1 line
2.28.0
Greg Kroah-Hartman
maintainerPATCH 9/9 sound: hiface: convert to use new usb_control functions...
In reply to Greg Kroah-Hartman--- sound/usb/hiface/pcm.c | 12 +++++------- 1 file changed, 5 insertions(+), 7 deletions(-)
sound/usb/hiface/pcm.c +5 -7
@@ -156,14 +156,12 @@ static int hiface_pcm_set_rate(struct pcm_runtime *rt, unsigned int rate)* This control message doesn't have any ack from the * other side */ - ret =usb_control_msg (device,usb_sndctrlpipe (device,0 ), -HIFACE_SET_RATE_REQUEST , -USB_DIR_OUT |USB_TYPE_VENDOR |USB_RECIP_OTHER , - rate_value,0 ,NULL ,0 ,100 ); -if (ret <0 ) { + ret =usb_control_msg_send (device,0 , +HIFACE_SET_RATE_REQUEST , +USB_DIR_OUT |USB_TYPE_VENDOR |USB_RECIP_OTHER , + rate_value,0 ,NULL ,0 ,100 ); +if (ret)dev_err (&device->dev,"Error setting samplerate %d.\n" , rate); -return ret; - }return 0 ; }
Signature · 1 line
2.28.0
Greg Kroah-Hartman
maintainerPATCH 10/10 Bluetooth: ath3k: use usb_control_msg_send() and usb_control_msg_recv()
In reply to Greg Kroah-HartmanThe usb_control_msg_send() and usb_control_msg_recv() calls can return an error if a "short" write/read happens, and they can handle data off of the stack, so move the driver over to using those calls instead, saving some logic when dynamically allocating memory.
--- drivers/bluetooth/ath3k.c | 90 +++++++++++---------------------------- 1 file changed, 26 insertions(+), 64 deletions(-)
drivers/bluetooth/ath3k.c +26 -64
@@ -212,19 +212,16 @@ static int ath3k_load_firmware(struct usb_device *udev,BT_DBG ("udev %p" , udev); - pipe =usb_sndctrlpipe (udev,0 ); - send_buf =kmalloc (BULK_SIZE ,GFP_KERNEL );if (!send_buf) {BT_ERR ("Can't allocate memory chunk for firmware" );return -ENOMEM ; } -memcpy (send_buf, firmware->data,FW_HDR_SIZE ); - err =usb_control_msg (udev, pipe,USB_REQ_DFU_DNLOAD ,USB_TYPE_VENDOR , -0 ,0 , send_buf,FW_HDR_SIZE , -USB_CTRL_SET_TIMEOUT ); -if (err <0 ) { + err =usb_control_msg_send (udev,0 ,USB_REQ_DFU_DNLOAD ,USB_TYPE_VENDOR , +0 ,0 , firmware->data,FW_HDR_SIZE , +USB_CTRL_SET_TIMEOUT ); +if (err) {BT_ERR ("Can't change to loading configuration err" ); goto error; }
@@ -259,44 +256,17 @@ static int ath3k_load_firmware(struct usb_device *udev,static int ath3k_get_state (struct usb_device *udev,unsigned char *state) { -int ret, pipe =0 ; -char *buf; - - buf =kmalloc (sizeof (*buf),GFP_KERNEL ); -if (!buf) -return -ENOMEM ; - - pipe =usb_rcvctrlpipe (udev,0 ); - ret =usb_control_msg (udev, pipe,ATH3K_GETSTATE , -USB_TYPE_VENDOR |USB_DIR_IN ,0 ,0 , - buf,sizeof (*buf),USB_CTRL_SET_TIMEOUT ); - - *state = *buf; -kfree (buf); - -return ret; +return usb_control_msg_recv (udev,0 ,ATH3K_GETSTATE , +USB_TYPE_VENDOR |USB_DIR_IN ,0 ,0 , + state,1 ,USB_CTRL_SET_TIMEOUT ); }static int ath3k_get_version (struct usb_device *udev,struct ath3k_version *version) { -int ret, pipe =0 ; -struct ath3k_version *buf; -const int size =sizeof (*buf); - - buf =kmalloc (size,GFP_KERNEL ); -if (!buf) -return -ENOMEM ; - - pipe =usb_rcvctrlpipe (udev,0 ); - ret =usb_control_msg (udev, pipe,ATH3K_GETVERSION , -USB_TYPE_VENDOR |USB_DIR_IN ,0 ,0 , - buf, size,USB_CTRL_SET_TIMEOUT ); - -memcpy (version, buf, size); -kfree (buf); - -return ret; +return usb_control_msg_recv (udev,0 ,ATH3K_GETVERSION , +USB_TYPE_VENDOR |USB_DIR_IN ,0 ,0 , + version,sizeof (*version),USB_CTRL_SET_TIMEOUT ); } static int ath3k_load_fwfile(struct usb_device *udev,
@@ -316,13 +286,10 @@ static int ath3k_load_fwfile(struct usb_device *udev, } size =min_t (uint, count,FW_HDR_SIZE ); -memcpy (send_buf, firmware->data, size); - pipe =usb_sndctrlpipe (udev,0 ); - ret =usb_control_msg (udev, pipe,ATH3K_DNLOAD , -USB_TYPE_VENDOR ,0 ,0 , send_buf, - size,USB_CTRL_SET_TIMEOUT ); -if (ret <0 ) { + ret =usb_control_msg_send (udev,0 ,ATH3K_DNLOAD ,USB_TYPE_VENDOR ,0 ,0 , + firmware->data, size,USB_CTRL_SET_TIMEOUT ); +if (ret) {BT_ERR ("Can't change to loading configuration err" );kfree (send_buf);return ret;
@@ -355,23 +322,19 @@ static int ath3k_load_fwfile(struct usb_device *udev,return 0 ; } -static int ath3k_switch_pid (struct usb_device *udev) +static void ath3k_switch_pid (struct usb_device *udev) { -int pipe =0 ; - - pipe =usb_sndctrlpipe (udev,0 ); -return usb_control_msg (udev, pipe,USB_REG_SWITCH_VID_PID , -USB_TYPE_VENDOR ,0 ,0 , -NULL ,0 ,USB_CTRL_SET_TIMEOUT ); +usb_control_msg_send (udev,0 ,USB_REG_SWITCH_VID_PID ,USB_TYPE_VENDOR , +0 ,0 ,NULL ,0 ,USB_CTRL_SET_TIMEOUT ); }static int ath3k_set_normal_mode (struct usb_device *udev) {unsigned char fw_state; -int pipe =0 , ret; +int ret; ret =ath3k_get_state (udev, &fw_state); -if (ret <0 ) { +if (ret) {BT_ERR ("Can't get state to change to normal mode err" );return ret; }
@@ -381,10 +344,9 @@ static int ath3k_set_normal_mode(struct usb_device *udev)return 0 ; } - pipe =usb_sndctrlpipe (udev,0 ); -return usb_control_msg (udev, pipe,ATH3K_SET_NORMAL_MODE , -USB_TYPE_VENDOR ,0 ,0 , -NULL ,0 ,USB_CTRL_SET_TIMEOUT ); +return usb_control_msg_send (udev,0 ,ATH3K_SET_NORMAL_MODE , +USB_TYPE_VENDOR ,0 ,0 ,NULL ,0 , +USB_CTRL_SET_TIMEOUT ); }static int ath3k_load_patch (struct usb_device *udev)
@@ -397,7 +359,7 @@ static int ath3k_load_patch(struct usb_device *udev)int ret; ret =ath3k_get_state (udev, &fw_state); -if (ret <0 ) { +if (ret) {BT_ERR ("Can't get state to change to load ram patch err" );return ret; }
@@ -408,7 +370,7 @@ static int ath3k_load_patch(struct usb_device *udev) } ret =ath3k_get_version (udev, &fw_version); -if (ret <0 ) { +if (ret) {BT_ERR ("Can't get version to change to load ram patch err" );return ret; }
@@ -449,13 +411,13 @@ static int ath3k_load_syscfg(struct usb_device *udev)int clk_value, ret; ret =ath3k_get_state (udev, &fw_state); -if (ret <0 ) { +if (ret) {BT_ERR ("Can't get state to change to load configuration err" );return -EBUSY ; } ret =ath3k_get_version (udev, &fw_version); -if (ret <0 ) { +if (ret) {BT_ERR ("Can't get version to change to load ram patch err" );return ret; }
@@ -529,7 +491,7 @@ static int ath3k_probe(struct usb_interface *intf,return ret; } ret =ath3k_set_normal_mode (udev); -if (ret <0 ) { +if (ret) {BT_ERR ("Set normal mode failed" );return ret; }
Signature · 1 line
2.28.0
Re: [PATCH 03/10] USB: core: message.c: use usb_control_msg_send() in a few places
In reply to Greg Kroah-HartmanQuoted 3 lines · Greg Kroah-Hartman
There are a few calls to
usb_control_msg()that can be converted to useusb_control_msg_send()instead, so do that in order to make the error checking a bit simpler.
Makes sense. Others will take this as a good example of API in use.
Quoted 98 lines
Cc Alan Stern <[email protected]>Cc "Rafael J. Wysocki" <[email protected]>Cc Andy Shevchenko <[email protected]>Signed-off-by Greg Kroah-Hartman <[email protected]>--- drivers/usb/core/message.c | 38 +++++++++++++++++++------------------- 1 file changed, 19 insertions(+), 19 deletions(-)drivers/usb/core/message.c +19
-19@@ -1081,7 +1081,7 @@ int usb_set_isoch_delay(struct usb_device *dev)if (dev->speed <USB_SPEED_SUPER )return 0 ; - return usb_control_msg(dev, usb_sndctrlpipe(dev, 0), + return usb_control_msg_send(dev, 0, USB_REQ_SET_ISOCH_DELAY, USB_DIR_OUT | USB_TYPE_STANDARD | USB_RECIP_DEVICE, dev->hub_delay, 0, NULL, 0,@@ -1203,13 +1203,13 @@ int usb_clear_halt(struct usb_device *dev, int pipe)* (like some ibmcam model 1 units) seem to expect hosts to make * this request for iso endpoints, which can't halt! */ - result =usb_control_msg (dev,usb_sndctrlpipe (dev,0 ), -USB_REQ_CLEAR_FEATURE ,USB_RECIP_ENDPOINT , -USB_ENDPOINT_HALT , endp,NULL ,0 , -USB_CTRL_SET_TIMEOUT ); + result =usb_control_msg_send (dev,0 , +USB_REQ_CLEAR_FEATURE ,USB_RECIP_ENDPOINT , +USB_ENDPOINT_HALT , endp,NULL ,0 , +USB_CTRL_SET_TIMEOUT );/* don't un-halt or force to DATA0 except on success */ -if (result <0 ) +if (result)return result;/* NOTE: seems like Microsoft and Apple don't bother verifying @@ -1558,9 +1558,10 @@ int usb_set_interface(struct usb_device *dev, int interface, int alternate)if (dev->quirks &USB_QUIRK_NO_SET_INTF ) ret = -EPIPE ;else - ret =usb_control_msg (dev,usb_sndctrlpipe (dev,0 ), -USB_REQ_SET_INTERFACE ,USB_RECIP_INTERFACE , - alternate, interface,NULL ,0 ,5000 ); + ret =usb_control_msg_send (dev,0 , +USB_REQ_SET_INTERFACE , +USB_RECIP_INTERFACE , alternate, + interface,NULL ,0 ,5000 );/* 9.4.10 says devices don't need this and are free to STALL the * request if the interface only has one alternate setting. @@ -1570,7 +1571,7 @@ int usb_set_interface(struct usb_device *dev, int interface, int alternate)"manual set_interface for iface %d, alt %d\n" , interface, alternate); manual =1 ; - }else if (ret <0 ) { + }else if (ret) {/* Re-instate the old alt setting */ usb_hcd_alloc_bandwidth (dev,NULL , alt, iface->cur_altsetting);usb_enable_lpm (dev);@@ -1718,11 +1719,10 @@ int usb_reset_configuration(struct usb_device *dev)mutex_unlock (hcd->bandwidth_mutex);return retval; } - retval =usb_control_msg (dev,usb_sndctrlpipe (dev,0 ), -USB_REQ_SET_CONFIGURATION ,0 , - config->desc.bConfigurationValue,0 , -NULL ,0 ,USB_CTRL_SET_TIMEOUT ); -if (retval <0 ) + retval =usb_control_msg_send (dev,0 ,USB_REQ_SET_CONFIGURATION ,0 , + config->desc.bConfigurationValue,0 , +NULL ,0 ,USB_CTRL_SET_TIMEOUT ); +if (retval) goto reset_old_alts;mutex_unlock (hcd->bandwidth_mutex);@@ -2103,10 +2103,10 @@ int usb_set_configuration(struct usb_device *dev, int configuration) }kfree (new_interfaces); - ret =usb_control_msg (dev,usb_sndctrlpipe (dev,0 ), -USB_REQ_SET_CONFIGURATION ,0 , configuration,0 , -NULL ,0 ,USB_CTRL_SET_TIMEOUT ); -if (ret <0 && cp) { + ret =usb_control_msg_send (dev,0 ,USB_REQ_SET_CONFIGURATION ,0 , + configuration,0 ,NULL ,0 , +USB_CTRL_SET_TIMEOUT ); +if (ret && cp) {/* * All the old state is gone, so what else can we do? * The device is probably useless now anyway. Signature · 1 line
2.28.0
Signature · 2 lines
With Best Regards, Andy Shevchenko
Re: [PATCH 01/10] USB: move snd_usb_pipe_sanity_check into the USB core
In reply to Greg Kroah-HartmanQuoted 17 lines · Greg Kroah-Hartman
snd_usb_pipe_sanity_check()is a great function, so let's move it into the USB core so that other parts of the kernel, including the USB core, can call it.Name it
usb_pipe_type_check()to match the existingusb_urb_ep_type_check()call, which now uses this function.Cc Jaroslav Kysela <[email protected]>Cc Takashi Iwai <[email protected]>Cc "Gustavo A. R. Silva" <[email protected]>Cc Eli Billauer <[email protected]>Cc Emiliano Ingrassia <[email protected]>Cc Alan Stern <[email protected]>Cc Alexander Tsoy <[email protected]>Cc "Geoffrey D. Bennett" <[email protected]>Cc Jussi Laako <[email protected]>
Quoted 8 lines
Cc Nick Kossifidis <[email protected]>Cc Dmitry Panchenko <[email protected]>Cc Chris Wulff <[email protected]>Cc Jesus Ramos <[email protected]>Signed-off-by Greg Kroah-Hartman <[email protected]>
thanks,
Takashi
Quoted 192 lines
--- drivers/usb/core/urb.c | 29 ++++++++++++++++++++++------- include/linux/usb.h | 1 + sound/usb/helper.c | 16 +--------------- sound/usb/helper.h | 1 - sound/usb/mixer_scarlett_gen2.c | 2 +- sound/usb/quirks.c | 12 ++++++------ 6 files changed, 31 insertions(+), 30 deletions(-)drivers/usb/core/urb.c +22
-7@@ -192,24 +192,39 @@ static const int pipetypes[4] = { };/** -* usb_urb_ep_type_check - sanity check of endpoint in the given urb -* @urb: urb to be checked +* usb_pipe_type_check - sanity check of a specific pipe for a usb device +* @dev: struct usb_device to be checked +* @pipe: pipe to check * * This performs a light-weight sanity check for the endpoint in the -* given urb. It returns 0 if the urb contains a valid endpoint, otherwise -* a negative error code. +* given usb device. It returns 0 if the pipe is a valid for the specific usb +* device, otherwise a negative error code. */ -int usb_urb_ep_type_check (const struct urb *urb) +int usb_pipe_type_check (struct usb_device *dev,unsigned int pipe) {const struct usb_host_endpoint *ep; - ep =usb_pipe_endpoint (urb->dev, urb->pipe); + ep =usb_pipe_endpoint (dev, pipe);if (!ep)return -EINVAL ; -if (usb_pipetype (urb->pipe) != pipetypes[usb_endpoint_type (&ep->desc)]) +if (usb_pipetype (pipe) != pipetypes[usb_endpoint_type (&ep->desc)])return -EINVAL ;return 0 ; } +EXPORT_SYMBOL_GPL (usb_pipe_type_check); + +/** +* usb_urb_ep_type_check - sanity check of endpoint in the given urb +* @urb: urb to be checked +* +* This performs a light-weight sanity check for the endpoint in the +* given urb. It returns 0 if the urb contains a valid endpoint, otherwise +* a negative error code. +*/ +int usb_urb_ep_type_check (const struct urb *urb) +{ +return usb_pipe_type_check (urb->dev, urb->pipe); +}EXPORT_SYMBOL_GPL (usb_urb_ep_type_check);/** include/linux/usb.h +1
-0@@ -1764,6 +1764,7 @@ static inline int usb_urb_dir_out(struct urb *urb)return (urb->transfer_flags &URB_DIR_MASK ) ==URB_DIR_OUT ; } +int usb_pipe_type_check (struct usb_device *dev,unsigned int pipe);int usb_urb_ep_type_check (const struct urb *urb); void *usb_alloc_coherent(struct usb_device *dev, size_t size,sound/usb/helper.c +1
-15@@ -63,20 +63,6 @@ void *snd_usb_find_csint_desc(void *buffer, int buflen, void *after, u8 dsubtypereturn NULL ; } -/* check the validity of pipe and EP types */ -int snd_usb_pipe_sanity_check (struct usb_device *dev,unsigned int pipe) -{ -static const int pipetypes[4 ] = { -PIPE_CONTROL ,PIPE_ISOCHRONOUS ,PIPE_BULK ,PIPE_INTERRUPT - }; -struct usb_host_endpoint *ep; - - ep =usb_pipe_endpoint (dev, pipe); -if (!ep ||usb_pipetype (pipe) != pipetypes[usb_endpoint_type (&ep->desc)]) -return -EINVAL ; -return 0 ; -} -/* * Wrapper for usb_control_msg(). * Allocates a temp buffer to prevent dmaing from/to the stack. @@ -89,7 +75,7 @@ int snd_usb_ctl_msg(struct usb_device *dev, unsigned int pipe, __u8 request,void *buf =NULL ;int timeout; -if (snd_usb_pipe_sanity_check (dev, pipe)) +if (usb_pipe_type_check (dev, pipe))return -EINVAL ;if (size >0 ) {sound/usb/helper.h +0
-1@@ -7,7 +7,6 @@ unsigned int snd_usb_combine_bytes(unsigned char *bytes, int size);void *snd_usb_find_desc (void *descstart,int desclen,void *after,u8 dtype);void *snd_usb_find_csint_desc (void *descstart,int desclen,void *after,u8 dsubtype); -int snd_usb_pipe_sanity_check (struct usb_device *dev,unsigned int pipe);int snd_usb_ctl_msg (struct usb_device *dev,unsigned int pipe,__u8 request,__u8 requesttype,__u16 value,__u16 index,void *data,__u16 size);sound/usb/mixer_scarlett_gen2.c +1
-1@@ -1978,7 +1978,7 @@ static int scarlett2_mixer_status_create(struct usb_mixer_interface *mixer)return 0 ; } -if (snd_usb_pipe_sanity_check (dev, pipe)) +if (usb_pipe_type_check (dev, pipe))return -EINVAL ; mixer->urb =usb_alloc_urb (0 ,GFP_KERNEL );sound/usb/quirks.c +6
-6@@ -846,7 +846,7 @@ static int snd_usb_accessmusic_boot_quirk(struct usb_device *dev)static const u8 seq[] = {0x4e ,0x73 ,0x52 ,0x01 };void *buf; -if (snd_usb_pipe_sanity_check (dev,usb_sndintpipe (dev,0x05 ))) +if (usb_pipe_type_check (dev,usb_sndintpipe (dev,0x05 )))return -EINVAL ; buf =kmemdup (seq,ARRAY_SIZE (seq),GFP_KERNEL );if (!buf)@@ -875,7 +875,7 @@ static int snd_usb_nativeinstruments_boot_quirk(struct usb_device *dev) {int ret; -if (snd_usb_pipe_sanity_check (dev,usb_sndctrlpipe (dev,0 ))) +if (usb_pipe_type_check (dev,usb_sndctrlpipe (dev,0 )))return -EINVAL ; ret = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), 0xaf, USB_TYPE_VENDOR | USB_RECIP_DEVICE,@@ -984,7 +984,7 @@ static int snd_usb_axefx3_boot_quirk(struct usb_device *dev)dev_dbg (&dev->dev,"Waiting for Axe-Fx III to boot up...\n" ); -if (snd_usb_pipe_sanity_check (dev,usb_sndctrlpipe (dev,0 ))) +if (usb_pipe_type_check (dev,usb_sndctrlpipe (dev,0 )))return -EINVAL ;/* If the Axe-Fx III has not fully booted, it will timeout when trying * to enable the audio streaming interface. A more generous timeout is @@ -1018,7 +1018,7 @@ static int snd_usb_motu_microbookii_communicate(struct usb_device *dev, u8 *buf, {int err, actual_length; -if (snd_usb_pipe_sanity_check (dev,usb_sndintpipe (dev,0x01 ))) +if (usb_pipe_type_check (dev,usb_sndintpipe (dev,0x01 )))return -EINVAL ; err =usb_interrupt_msg (dev,usb_sndintpipe (dev,0x01 ), buf, *length, &actual_length,1000 );@@ -1030,7 +1030,7 @@ static int snd_usb_motu_microbookii_communicate(struct usb_device *dev, u8 *buf,memset (buf,0 , buf_size); -if (snd_usb_pipe_sanity_check (dev,usb_rcvintpipe (dev,0x82 ))) +if (usb_pipe_type_check (dev,usb_rcvintpipe (dev,0x82 )))return -EINVAL ; err =usb_interrupt_msg (dev,usb_rcvintpipe (dev,0x82 ), buf, buf_size, &actual_length,1000 );@@ -1117,7 +1117,7 @@ static int snd_usb_motu_m_series_boot_quirk(struct usb_device *dev) {int ret; -if (snd_usb_pipe_sanity_check (dev,usb_sndctrlpipe (dev,0 ))) +if (usb_pipe_type_check (dev,usb_sndctrlpipe (dev,0 )))return -EINVAL ; ret = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), 1, USB_TYPE_VENDOR | USB_RECIP_DEVICE,Signature · 1 line
2.28.0
Re: [PATCH 06/10] sound: usx2y: move to use usb_control_msg_send()
In reply to Greg Kroah-HartmanQuoted 10 lines · Greg Kroah-Hartman
The
usb_control_msg_send()call can handle data on the stack, as well as returning an error if a "short" write happens, so move the driver over to using that call instead. This ends up removing a helper function that is no longer needed.Cc Jaroslav Kysela <[email protected]>Cc Takashi Iwai <[email protected]>Signed-off-by Greg Kroah-Hartman <[email protected]>
thanks,
Takashi
Quoted 71 lines
--- sound/usb/usx2y/us122l.c | 42 ++++++++-------------------------------- 1 file changed, 8 insertions(+), 34 deletions(-)sound/usb/usx2y/us122l.c +8
-34@@ -82,40 +82,13 @@ static int us144_create_usbmidi(struct snd_card *card) &US122L(card)->midi_list, &quirk); } -/* -* Wrapper for usb_control_msg(). -* Allocates a temp buffer to prevent dmaing from/to the stack. -*/ -static int us122l_ctl_msg (struct usb_device *dev,unsigned int pipe, -__u8 request,__u8 requesttype, -__u16 value,__u16 index,void *data, -__u16 size,int timeout) -{ -int err; -void *buf =NULL ; - -if (size >0 ) { - buf =kmemdup (data, size,GFP_KERNEL ); -if (!buf) -return -ENOMEM ; - } - err =usb_control_msg (dev, pipe, request, requesttype, - value, index, buf, size, timeout); -if (size >0 ) { -memcpy (data, buf, size); -kfree (buf); - } -return err; -} -static void pt_info_set (struct usb_device *dev,u8 v) {int ret; - ret =usb_control_msg (dev,usb_sndctrlpipe (dev,0 ), -'I' , -USB_DIR_OUT |USB_TYPE_VENDOR |USB_RECIP_DEVICE , - v,0 ,NULL ,0 ,1000 ); + ret =usb_control_msg_send (dev,0 ,'I' , +USB_DIR_OUT |USB_TYPE_VENDOR |USB_RECIP_DEVICE , + v,0 ,NULL ,0 ,1000 );snd_printdd (KERN_DEBUG "%i\n" , ret); }@@ -305,10 +278,11 @@ static int us122l_set_sample_rate(struct usb_device *dev, int rate) data[0 ] = rate; data[1 ] = rate >>8 ; data[2 ] = rate >>16 ; - err =us122l_ctl_msg (dev,usb_sndctrlpipe (dev,0 ),UAC_SET_CUR , -USB_TYPE_CLASS |USB_RECIP_ENDPOINT |USB_DIR_OUT , -UAC_EP_CS_ATTR_SAMPLE_RATE <<8 , ep, data,3 ,1000 ); -if (err <0 ) + err =usb_control_msg_send (dev,0 ,UAC_SET_CUR , +USB_TYPE_CLASS |USB_RECIP_ENDPOINT |USB_DIR_OUT , +UAC_EP_CS_ATTR_SAMPLE_RATE <<8 , ep, data,3 , +1000 ); +if (err)snd_printk (KERN_ERR "%d: cannot set freq %d to ep 0x%x\n" , dev->devnum, rate, ep);return err;Signature · 1 line
2.28.0
Re: [PATCH 07/10] sound: 6fire: move to use usb_control_msg_send() and usb_control_msg_recv()
In reply to Greg Kroah-HartmanQuoted 6 lines · Greg Kroah-Hartman
The
usb_control_msg_send()andusb_control_msg_recv()calls can return an error if a "short" write/read happens, so move the driver over to using those calls instead, saving some logic in the wrapper functions that were being used in this driver.
Quoted 7 lines
This also resolves a long-staging bug where data on the stack was being sent in a USB control message, which was not allowed.
Cc Jaroslav Kysela <[email protected]>Cc Takashi Iwai <[email protected]>Signed-off-by Greg Kroah-Hartman <[email protected]>
thanks,
Takashi
Quoted 110 lines
--- sound/usb/6fire/firmware.c | 38 +++++++++++++------------------------- 1 file changed, 13 insertions(+), 25 deletions(-)sound/usb/6fire/firmware.c +13
-25@@ -158,29 +158,17 @@ static int usb6fire_fw_ihex_init(const struct firmware *fw,static int usb6fire_fw_ezusb_write (struct usb_device *device,int type,int value,char *data,int len) { -int ret; - - ret =usb_control_msg (device,usb_sndctrlpipe (device,0 ), type, -USB_DIR_OUT |USB_TYPE_VENDOR |USB_RECIP_DEVICE , - value,0 , data, len,HZ ); -if (ret <0 ) -return ret; -else if (ret != len) -return -EIO ; -return 0 ; +return usb_control_msg_send (device,0 , type, +USB_DIR_OUT |USB_TYPE_VENDOR |USB_RECIP_DEVICE , + value,0 , data, len,HZ ); }static int usb6fire_fw_ezusb_read (struct usb_device *device,int type,int value,char *data,int len) { -int ret =usb_control_msg (device,usb_rcvctrlpipe (device,0 ), type, -USB_DIR_IN |USB_TYPE_VENDOR |USB_RECIP_DEVICE , value, -0 , data, len,HZ ); -if (ret <0 ) -return ret; -else if (ret != len) -return -EIO ; -return 0 ; +return usb_control_msg_recv (device,0 , type, +USB_DIR_IN |USB_TYPE_VENDOR |USB_RECIP_DEVICE , + value,0 , data, len,HZ ); } static int usb6fire_fw_fpga_write(struct usb_device *device,@@ -230,7 +218,7 @@ static int usb6fire_fw_ezusb_upload(/* upload firmware image */ data =0x01 ;/* stop ezusb cpu */ ret =usb6fire_fw_ezusb_write (device,0xa0 ,0xe600 , &data,1 ); -if (ret <0 ) { +if (ret) {kfree (rec);release_firmware (fw); dev_err(&intf->dev,@@ -242,7 +230,7 @@ static int usb6fire_fw_ezusb_upload(while (usb6fire_fw_ihex_next_record (rec)) {/* write firmware */ ret =usb6fire_fw_ezusb_write (device,0xa0 , rec->address, rec->data, rec->len); -if (ret <0 ) { +if (ret) {kfree (rec);release_firmware (fw); dev_err(&intf->dev,@@ -257,7 +245,7 @@ static int usb6fire_fw_ezusb_upload(if (postdata) {/* write data after firmware has been uploaded */ ret =usb6fire_fw_ezusb_write (device,0xa0 , postaddr, postdata, postlen); -if (ret <0 ) { +if (ret) {dev_err (&intf->dev,"unable to upload ezusb firmware %s: post urb.\n" , fwname);@@ -267,7 +255,7 @@ static int usb6fire_fw_ezusb_upload( data =0x00 ;/* resume ezusb cpu */ ret =usb6fire_fw_ezusb_write (device,0xa0 ,0xe600 , &data,1 ); -if (ret <0 ) { +if (ret) {dev_err (&intf->dev,"unable to upload ezusb firmware %s: end message.\n" , fwname);@@ -302,7 +290,7 @@ static int usb6fire_fw_fpga_upload( end = fw->data + fw->size; ret =usb6fire_fw_ezusb_write (device,8 ,0 ,NULL ,0 ); -if (ret <0 ) { +if (ret) {kfree (buffer);release_firmware (fw); dev_err(&intf->dev,@@ -327,7 +315,7 @@ static int usb6fire_fw_fpga_upload(kfree (buffer); ret =usb6fire_fw_ezusb_write (device,9 ,0 ,NULL ,0 ); -if (ret <0 ) { +if (ret) {dev_err (&intf->dev,"unable to upload fpga firmware: end urb.\n" );return ret;@@ -363,7 +351,7 @@ int usb6fire_fw_init(struct usb_interface *intf)u8 buffer[12 ]; ret =usb6fire_fw_ezusb_read (device,1 ,0 , buffer,8 ); -if (ret <0 ) { +if (ret) {dev_err (&intf->dev,"unable to receive device firmware state.\n" );return ret;Signature · 1 line
2.28.0
Re: [PATCH 08/10] sound: line6: move to use usb_control_msg_send() and usb_control_msg_recv()
In reply to Greg Kroah-HartmanQuoted 11 lines · Greg Kroah-Hartman
The
usb_control_msg_send()andusb_control_msg_recv()calls can return an error if a "short" write/read happens, and they can handle data off of the stack, so move the driver over to using those calls instead, saving some logic when dynamically allocating memory.Cc Jaroslav Kysela <[email protected]>Cc Takashi Iwai <[email protected]>Cc Vasily Khoruzhick <[email protected]>Signed-off-by Greg Kroah-Hartman <[email protected]>
thanks,
Takashi
Quoted 212 lines
--- sound/usb/line6/driver.c | 69 +++++++++++++++----------------------- sound/usb/line6/podhd.c | 17 ++++------ sound/usb/line6/toneport.c | 8 ++--- 3 files changed, 37 insertions(+), 57 deletions(-)sound/usb/line6/driver.c +27
-42@@ -337,23 +337,18 @@ int line6_read_data(struct usb_line6 *line6, unsigned address, void *data, {struct usb_device *usbdev = line6->usbdev;int ret; -unsigned char *len; +u8 len;unsigned count;if (address >0xffff || datalen >0xff )return -EINVAL ; - len =kmalloc (1 ,GFP_KERNEL ); -if (!len) -return -ENOMEM ; -/* query the serial number: */ - ret =usb_control_msg (usbdev,usb_sndctrlpipe (usbdev,0 ),0x67 , -USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_OUT , - (datalen <<8 ) |0x21 , address, -NULL ,0 ,LINE6_TIMEOUT *HZ ); - -if (ret <0 ) { + ret =usb_control_msg_send (usbdev,0 ,0x67 , +USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_OUT , + (datalen <<8 ) |0x21 , address,NULL ,0 , +LINE6_TIMEOUT *HZ ); +if (ret) {dev_err (line6->ifcdev,"read request failed (error %d)\n" , ret); goto exit; }@@ -362,45 +357,41 @@ int line6_read_data(struct usb_line6 *line6, unsigned address, void *data,for (count =0 ; count <LINE6_READ_WRITE_MAX_RETRIES ; count++) {mdelay (LINE6_READ_WRITE_STATUS_DELAY ); - ret =usb_control_msg (usbdev,usb_rcvctrlpipe (usbdev,0 ),0x67 , -USB_TYPE_VENDOR |USB_RECIP_DEVICE | -USB_DIR_IN , -0x0012 ,0x0000 , len,1 , -LINE6_TIMEOUT *HZ ); -if (ret <0 ) { + ret =usb_control_msg_recv (usbdev,0 ,0x67 , +USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_IN , +0x0012 ,0x0000 , &len,1 , +LINE6_TIMEOUT *HZ ); +if (ret) {dev_err (line6->ifcdev,"receive length failed (error %d)\n" , ret); goto exit; } -if (*len !=0xff ) +if (len !=0xff )break ; } ret = -EIO ; -if (*len ==0xff ) { +if (len ==0xff ) {dev_err (line6->ifcdev,"read failed after %d retries\n" , count); goto exit; - }else if (*len != datalen) { + }else if (len != datalen) {/* should be equal or something went wrong */ dev_err (line6->ifcdev,"length mismatch (expected %d, got %d)\n" , - (int )datalen, (int )*len); + (int )datalen, len); goto exit; }/* receive the result: */ - ret =usb_control_msg (usbdev,usb_rcvctrlpipe (usbdev,0 ),0x67 , -USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_IN , -0x0013 ,0x0000 , data, datalen, -LINE6_TIMEOUT *HZ ); - -if (ret <0 ) + ret =usb_control_msg_recv (usbdev,0 ,0x67 , +USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_IN , +0x0013 ,0x0000 , data, datalen,LINE6_TIMEOUT *HZ ); +if (ret)dev_err (line6->ifcdev,"read failed (error %d)\n" , ret); exit: -kfree (len);return ret; }EXPORT_SYMBOL_GPL (line6_read_data);@@ -423,12 +414,10 @@ int line6_write_data(struct usb_line6 *line6, unsigned address, void *data,if (!status)return -ENOMEM ; - ret =usb_control_msg (usbdev,usb_sndctrlpipe (usbdev,0 ),0x67 , -USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_OUT , -0x0022 , address, data, datalen, -LINE6_TIMEOUT *HZ ); - -if (ret <0 ) { + ret =usb_control_msg_send (usbdev,0 ,0x67 , +USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_OUT , +0x0022 , address, data, datalen,LINE6_TIMEOUT *HZ ); +if (ret) {dev_err (line6->ifcdev,"write request failed (error %d)\n" , ret); goto exit;@@ -437,14 +426,10 @@ int line6_write_data(struct usb_line6 *line6, unsigned address, void *data,for (count =0 ; count <LINE6_READ_WRITE_MAX_RETRIES ; count++) {mdelay (LINE6_READ_WRITE_STATUS_DELAY ); - ret =usb_control_msg (usbdev,usb_rcvctrlpipe (usbdev,0 ), -0x67 , -USB_TYPE_VENDOR |USB_RECIP_DEVICE | -USB_DIR_IN , -0x0012 ,0x0000 , - status,1 ,LINE6_TIMEOUT *HZ ); - -if (ret <0 ) { + ret =usb_control_msg_recv (usbdev,0 ,0x67 , +USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_IN , +0x0012 ,0x0000 , status,1 ,LINE6_TIMEOUT *HZ ); +if (ret) {dev_err (line6->ifcdev,"receiving status failed (error %d)\n" , ret); goto exit;sound/usb/line6/podhd.c +6
-11@@ -183,29 +183,25 @@ static const struct attribute_group podhd_dev_attr_group = {static int podhd_dev_start (struct usb_line6_podhd *pod) {int ret; -u8 *init_bytes; +u8 init_bytes[8 ];int i;struct usb_device *usbdev = pod->line6.usbdev; - init_bytes =kmalloc (8 ,GFP_KERNEL ); -if (!init_bytes) -return -ENOMEM ; - - ret =usb_control_msg (usbdev,usb_sndctrlpipe (usbdev,0 ), + ret =usb_control_msg_send (usbdev,0 ,0x67 ,USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_OUT ,0x11 ,0 ,NULL ,0 ,LINE6_TIMEOUT *HZ ); -if (ret <0 ) { +if (ret) {dev_err (pod->line6.ifcdev,"read request failed (error %d)\n" , ret); goto exit; }/* NOTE: looks like some kind of ping message */ - ret =usb_control_msg (usbdev,usb_rcvctrlpipe (usbdev,0 ),0x67 , + ret =usb_control_msg_recv (usbdev,0 ,0x67 ,USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_IN ,0x11 ,0x0 , init_bytes,3 ,LINE6_TIMEOUT *HZ ); -if (ret <0 ) { +if (ret) {dev_err (pod->line6.ifcdev,"receive length failed (error %d)\n" , ret); goto exit;@@ -220,13 +216,12 @@ static int podhd_dev_start(struct usb_line6_podhd *pod) goto exit; } - ret =usb_control_msg (usbdev,usb_sndctrlpipe (usbdev,0 ), + ret =usb_control_msg_send (usbdev,0 ,USB_REQ_SET_FEATURE ,USB_TYPE_STANDARD |USB_RECIP_DEVICE |USB_DIR_OUT ,1 ,0 ,NULL ,0 ,LINE6_TIMEOUT *HZ ); exit: -kfree (init_bytes);return ret; }sound/usb/line6/toneport.c +4
-4@@ -126,11 +126,11 @@ static int toneport_send_cmd(struct usb_device *usbdev, int cmd1, int cmd2) {int ret; - ret =usb_control_msg (usbdev,usb_sndctrlpipe (usbdev,0 ),0x67 , -USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_OUT , - cmd1, cmd2,NULL ,0 ,LINE6_TIMEOUT *HZ ); + ret =usb_control_msg_send (usbdev,0 ,0x67 , +USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_OUT , + cmd1, cmd2,NULL ,0 ,LINE6_TIMEOUT *HZ ); -if (ret <0 ) { +if (ret) {dev_err (&usbdev->dev,"send failed (error %d)\n" , ret);return ret; }Signature · 1 line
2.28.0
Re: [PATCH 09/10] sound: hiface: move to use usb_control_msg_send()
In reply to Greg Kroah-HartmanQuoted 8 lines · Greg Kroah-Hartman
The
usb_control_msg_send()call can return an error if a "short" write happens, so move the driver over to using that call instead.Cc Jaroslav Kysela <[email protected]>Cc Takashi Iwai <[email protected]>Signed-off-by Greg Kroah-Hartman <[email protected]>
thanks,
Takashi
Quoted 34 lines
--- sound/usb/hiface/pcm.c | 14 ++++++-------- 1 file changed, 6 insertions(+), 8 deletions(-)sound/usb/hiface/pcm.c +6
-8@@ -156,16 +156,14 @@ static int hiface_pcm_set_rate(struct pcm_runtime *rt, unsigned int rate)* This control message doesn't have any ack from the * other side */ - ret =usb_control_msg (device,usb_sndctrlpipe (device,0 ), -HIFACE_SET_RATE_REQUEST , -USB_DIR_OUT |USB_TYPE_VENDOR |USB_RECIP_OTHER , - rate_value,0 ,NULL ,0 ,100 ); -if (ret <0 ) { + ret =usb_control_msg_send (device,0 , +HIFACE_SET_RATE_REQUEST , +USB_DIR_OUT |USB_TYPE_VENDOR |USB_RECIP_OTHER , + rate_value,0 ,NULL ,0 ,100 ); +if (ret)dev_err (&device->dev,"Error setting samplerate %d.\n" , rate); -return ret; - } -return 0 ; +return ret; } static struct pcm_substream *hiface_pcm_get_substream(struct snd_pcm_substreamSignature · 1 line
2.28.0
Re: [PATCH 7/9] sound: line6: convert to use new usb control function...
In reply to Greg Kroah-HartmanQuoted 2 lines · Greg Kroah-Hartman
Signed-off-by Greg Kroah-Hartman <[email protected]>
I guess this and a few others with (x/9) are stale patches, right?
thanks,
Takashi
Quoted 212 lines
--- sound/usb/line6/driver.c | 69 +++++++++++++++----------------------- sound/usb/line6/podhd.c | 17 ++++------ sound/usb/line6/toneport.c | 8 ++--- 3 files changed, 37 insertions(+), 57 deletions(-)sound/usb/line6/driver.c +27
-42@@ -337,23 +337,18 @@ int line6_read_data(struct usb_line6 *line6, unsigned address, void *data, {struct usb_device *usbdev = line6->usbdev;int ret; -unsigned char *len; +u8 len;unsigned count;if (address >0xffff || datalen >0xff )return -EINVAL ; - len =kmalloc (1 ,GFP_KERNEL ); -if (!len) -return -ENOMEM ; -/* query the serial number: */ - ret =usb_control_msg (usbdev,usb_sndctrlpipe (usbdev,0 ),0x67 , -USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_OUT , - (datalen <<8 ) |0x21 , address, -NULL ,0 ,LINE6_TIMEOUT *HZ ); - -if (ret <0 ) { + ret =usb_control_msg_send (usbdev,0 ,0x67 , +USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_OUT , + (datalen <<8 ) |0x21 , address,NULL ,0 , +LINE6_TIMEOUT *HZ ); +if (ret) {dev_err (line6->ifcdev,"read request failed (error %d)\n" , ret); goto exit; }@@ -362,45 +357,41 @@ int line6_read_data(struct usb_line6 *line6, unsigned address, void *data,for (count =0 ; count <LINE6_READ_WRITE_MAX_RETRIES ; count++) {mdelay (LINE6_READ_WRITE_STATUS_DELAY ); - ret =usb_control_msg (usbdev,usb_rcvctrlpipe (usbdev,0 ),0x67 , -USB_TYPE_VENDOR |USB_RECIP_DEVICE | -USB_DIR_IN , -0x0012 ,0x0000 , len,1 , -LINE6_TIMEOUT *HZ ); -if (ret <0 ) { + ret =usb_control_msg_recv (usbdev,0 ,0x67 , +USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_IN , +0x0012 ,0x0000 , &len,1 , +LINE6_TIMEOUT *HZ ); +if (ret) {dev_err (line6->ifcdev,"receive length failed (error %d)\n" , ret); goto exit; } -if (*len !=0xff ) +if (len !=0xff )break ; } ret = -EIO ; -if (*len ==0xff ) { +if (len ==0xff ) {dev_err (line6->ifcdev,"read failed after %d retries\n" , count); goto exit; - }else if (*len != datalen) { + }else if (len != datalen) {/* should be equal or something went wrong */ dev_err (line6->ifcdev,"length mismatch (expected %d, got %d)\n" , - (int )datalen, (int )*len); + (int )datalen, len); goto exit; }/* receive the result: */ - ret =usb_control_msg (usbdev,usb_rcvctrlpipe (usbdev,0 ),0x67 , -USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_IN , -0x0013 ,0x0000 , data, datalen, -LINE6_TIMEOUT *HZ ); - -if (ret <0 ) + ret =usb_control_msg_recv (usbdev,0 ,0x67 , +USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_IN , +0x0013 ,0x0000 , data, datalen,LINE6_TIMEOUT *HZ ); +if (ret)dev_err (line6->ifcdev,"read failed (error %d)\n" , ret); exit: -kfree (len);return ret; }EXPORT_SYMBOL_GPL (line6_read_data);@@ -423,12 +414,10 @@ int line6_write_data(struct usb_line6 *line6, unsigned address, void *data,if (!status)return -ENOMEM ; - ret =usb_control_msg (usbdev,usb_sndctrlpipe (usbdev,0 ),0x67 , -USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_OUT , -0x0022 , address, data, datalen, -LINE6_TIMEOUT *HZ ); - -if (ret <0 ) { + ret =usb_control_msg_send (usbdev,0 ,0x67 , +USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_OUT , +0x0022 , address, data, datalen,LINE6_TIMEOUT *HZ ); +if (ret) {dev_err (line6->ifcdev,"write request failed (error %d)\n" , ret); goto exit;@@ -437,14 +426,10 @@ int line6_write_data(struct usb_line6 *line6, unsigned address, void *data,for (count =0 ; count <LINE6_READ_WRITE_MAX_RETRIES ; count++) {mdelay (LINE6_READ_WRITE_STATUS_DELAY ); - ret =usb_control_msg (usbdev,usb_rcvctrlpipe (usbdev,0 ), -0x67 , -USB_TYPE_VENDOR |USB_RECIP_DEVICE | -USB_DIR_IN , -0x0012 ,0x0000 , - status,1 ,LINE6_TIMEOUT *HZ ); - -if (ret <0 ) { + ret =usb_control_msg_recv (usbdev,0 ,0x67 , +USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_IN , +0x0012 ,0x0000 , status,1 ,LINE6_TIMEOUT *HZ ); +if (ret) {dev_err (line6->ifcdev,"receiving status failed (error %d)\n" , ret); goto exit;sound/usb/line6/podhd.c +6
-11@@ -183,29 +183,25 @@ static const struct attribute_group podhd_dev_attr_group = {static int podhd_dev_start (struct usb_line6_podhd *pod) {int ret; -u8 *init_bytes; +u8 init_bytes[8 ];int i;struct usb_device *usbdev = pod->line6.usbdev; - init_bytes =kmalloc (8 ,GFP_KERNEL ); -if (!init_bytes) -return -ENOMEM ; - - ret =usb_control_msg (usbdev,usb_sndctrlpipe (usbdev,0 ), + ret =usb_control_msg_send (usbdev,0 ,0x67 ,USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_OUT ,0x11 ,0 ,NULL ,0 ,LINE6_TIMEOUT *HZ ); -if (ret <0 ) { +if (ret) {dev_err (pod->line6.ifcdev,"read request failed (error %d)\n" , ret); goto exit; }/* NOTE: looks like some kind of ping message */ - ret =usb_control_msg (usbdev,usb_rcvctrlpipe (usbdev,0 ),0x67 , + ret =usb_control_msg_recv (usbdev,0 ,0x67 ,USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_IN ,0x11 ,0x0 , init_bytes,3 ,LINE6_TIMEOUT *HZ ); -if (ret <0 ) { +if (ret) {dev_err (pod->line6.ifcdev,"receive length failed (error %d)\n" , ret); goto exit;@@ -220,13 +216,12 @@ static int podhd_dev_start(struct usb_line6_podhd *pod) goto exit; } - ret =usb_control_msg (usbdev,usb_sndctrlpipe (usbdev,0 ), + ret =usb_control_msg_send (usbdev,0 ,USB_REQ_SET_FEATURE ,USB_TYPE_STANDARD |USB_RECIP_DEVICE |USB_DIR_OUT ,1 ,0 ,NULL ,0 ,LINE6_TIMEOUT *HZ ); exit: -kfree (init_bytes);return ret; }sound/usb/line6/toneport.c +4
-4@@ -126,11 +126,11 @@ static int toneport_send_cmd(struct usb_device *usbdev, int cmd1, int cmd2) {int ret; - ret =usb_control_msg (usbdev,usb_sndctrlpipe (usbdev,0 ),0x67 , -USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_OUT , - cmd1, cmd2,NULL ,0 ,LINE6_TIMEOUT *HZ ); + ret =usb_control_msg_send (usbdev,0 ,0x67 , +USB_TYPE_VENDOR |USB_RECIP_DEVICE |USB_DIR_OUT , + cmd1, cmd2,NULL ,0 ,LINE6_TIMEOUT *HZ ); -if (ret <0 ) { +if (ret) {dev_err (&usbdev->dev,"send failed (error %d)\n" , ret);return ret; }Signature · 1 line
2.28.0
Re: [PATCH 04/10] USB: core: hub.c: use usb_control_msg_send() in a few places
In reply to Greg Kroah-HartmanQuoted 6 lines · Greg Kroah-Hartman
There are a few calls to
usb_control_msg()that can be converted to useusb_control_msg_send()instead, so do that in order to make the error checking a bit simpler and the code smaller.Cc Alan Stern <[email protected]>Signed-off-by Greg Kroah-Hartman <[email protected]>
One problem in this patch...
Quoted 22 lines
drivers/usb/core/hub.c +4
-13@@ -3896,27 +3875,14 @@ static int usb_req_set_sel(struct usb_device *udev, enum usb3_link_state state)if (u2_pel >USB3_LPM_MAX_U2_SEL_PEL ) u2_pel =USB3_LPM_MAX_U2_SEL_PEL ; -/* -* usb_enable_lpm() can be called as part of a failed device reset, -* which may be initiated by an error path of a mass storage driver. -* Therefore, use GFP_NOIO. -*/ - sel_values =kmalloc (sizeof *(sel_values),GFP_NOIO ); -if (!sel_values) -return -ENOMEM ; - - sel_values->u1_sel = u1_sel; - sel_values->u1_pel = u1_pel; - sel_values->u2_sel =cpu_to_le16 (u2_sel); - sel_values->u2_pel =cpu_to_le16 (u2_pel); + sel_values.u1_sel = u1_sel; + sel_values.u1_pel = u1_pel; + sel_values.u2_sel =cpu_to_le16 (u2_sel); + sel_values.u2_pel =cpu_to_le16 (u2_pel);
drivers/usb/core/hub.c static int usb_req_set_sel(struct usb_device *udev, enum usb3_link_state state) · line 3885
Quoted 10 lines
drivers/usb/core/hub.c +3
-7- ret =usb_control_msg (udev,usb_sndctrlpipe (udev,0 ), -USB_REQ_SET_SEL , -USB_RECIP_DEVICE , -0 ,0 , - sel_values,sizeof *(sel_values), -USB_CTRL_SET_TIMEOUT ); -kfree (sel_values); + ret =usb_control_msg_send (udev,0 ,USB_REQ_SET_SEL ,USB_RECIP_DEVICE , +0 ,0 , &sel_values,sizeof (sel_values), +USB_CTRL_SET_TIMEOUT );
This effectively changes GFP_NOIO to GFP_KERNEL. Probably you should leave this particular call alone.
Alan Stern
Greg Kroah-Hartman
maintainerRe: [PATCH 04/10] USB: core: hub.c: use usb_control_msg_send() in a few places
Quoted 32 lines · Alan Stern
Quoted 6 lines · Greg Kroah-Hartman
There are a few calls to
usb_control_msg()that can be converted to useusb_control_msg_send()instead, so do that in order to make the error checking a bit simpler and the code smaller.Cc Alan Stern <[email protected]>Signed-off-by Greg Kroah-Hartman <[email protected]>One problem in this patch...
Quoted 22 lines
drivers/usb/core/hub.c +4
-13@@ -3896,27 +3875,14 @@ static int usb_req_set_sel(struct usb_device *udev, enum usb3_link_state state)if (u2_pel >USB3_LPM_MAX_U2_SEL_PEL ) u2_pel =USB3_LPM_MAX_U2_SEL_PEL ; -/* -* usb_enable_lpm() can be called as part of a failed device reset, -* which may be initiated by an error path of a mass storage driver. -* Therefore, use GFP_NOIO. -*/ - sel_values =kmalloc (sizeof *(sel_values),GFP_NOIO ); -if (!sel_values) -return -ENOMEM ; - - sel_values->u1_sel = u1_sel; - sel_values->u1_pel = u1_pel; - sel_values->u2_sel =cpu_to_le16 (u2_sel); - sel_values->u2_pel =cpu_to_le16 (u2_pel); + sel_values.u1_sel = u1_sel; + sel_values.u1_pel = u1_pel; + sel_values.u2_sel =cpu_to_le16 (u2_sel); + sel_values.u2_pel =cpu_to_le16 (u2_pel);
Quoted 13 lines
drivers/usb/core/hub.c static int usb_req_set_sel(struct usb_device *udev, enum usb3_link_state state) · line 3885
Quoted 10 lines
drivers/usb/core/hub.c +3
-7- ret =usb_control_msg (udev,usb_sndctrlpipe (udev,0 ), -USB_REQ_SET_SEL , -USB_RECIP_DEVICE , -0 ,0 , - sel_values,sizeof *(sel_values), -USB_CTRL_SET_TIMEOUT ); -kfree (sel_values); + ret =usb_control_msg_send (udev,0 ,USB_REQ_SET_SEL ,USB_RECIP_DEVICE , +0 ,0 , &sel_values,sizeof (sel_values), +USB_CTRL_SET_TIMEOUT );This effectively changes
GFP_NOIOtoGFP_KERNEL. Probably you should leave this particular call alone.
I thought about that, but for some reason thought that usb_control_msg() would eventually call for an allocation with GFP_KERNEL, but I was wrong, usb_internal_control_msg() calls usb_alloc_urb() with GFP_NOIO, my fault. I'll go fix this up, thanks for the review.
greg k-h
Greg Kroah-Hartman
maintainerRe: [PATCH 7/9] sound: line6: convert to use new usb control function...
In reply to Takashi IwaiQuoted 6 lines · Takashi Iwai
Quoted 2 lines · Greg Kroah-Hartman
Signed-off-by Greg Kroah-Hartman <[email protected]>I guess this and a few others with (x/9) are stale patches, right?
Ugh, yes, those were still in my directory, my fault for using 'git send-email *patch'
:(
greg k-h
Re: [PATCH 01/10] USB: move snd_usb_pipe_sanity_check into the USB core
In reply to Greg Kroah-HartmanQuoted 34 lines · Greg Kroah-Hartman
snd_usb_pipe_sanity_check()is a great function, so let's move it into the USB core so that other parts of the kernel, including the USB core, can call it.Name it
usb_pipe_type_check()to match the existingusb_urb_ep_type_check()call, which now uses this function.Cc Jaroslav Kysela <[email protected]>Cc Takashi Iwai <[email protected]>Cc "Gustavo A. R. Silva" <[email protected]>Cc Eli Billauer <[email protected]>Cc Emiliano Ingrassia <[email protected]>Cc Alan Stern <[email protected]>Cc Alexander Tsoy <[email protected]>Cc "Geoffrey D. Bennett" <[email protected]>Cc Jussi Laako <[email protected]>Cc Nick Kossifidis <[email protected]>Cc Dmitry Panchenko <[email protected]>Cc Chris Wulff <[email protected]>Cc Jesus Ramos <[email protected]>Signed-off-by Greg Kroah-Hartman <[email protected]>---
drivers/usb/core/urb.c +0
-0@@ -192,24 +192,39 @@ static const int pipetypes[4] = { };/**
drivers/usb/core/urb.c static const int pipetypes[4] = { · line 200
Quoted 10 lines
drivers/usb/core/urb.c +4
-4-* usb_urb_ep_type_check - sanity check of endpoint in the given urb -* @urb: urb to be checked +* usb_pipe_type_check - sanity check of a specific pipe for a usb device +* @dev: struct usb_device to be checked +* @pipe: pipe to check * * This performs a light-weight sanity check for the endpoint in the -* given urb. It returns 0 if the urb contains a valid endpoint, otherwise -* a negative error code. +* given usb device. It returns 0 if the pipe is a valid for the specific usb
-----------------------------------------------------^ Typo.
Quoted 21 lines
drivers/usb/core/urb.c +9
-3+* device, otherwise a negative error code. */ -int usb_urb_ep_type_check (const struct urb *urb) +int usb_pipe_type_check (struct usb_device *dev,unsigned int pipe) {const struct usb_host_endpoint *ep; - ep =usb_pipe_endpoint (urb->dev, urb->pipe); + ep =usb_pipe_endpoint (dev, pipe);if (!ep)return -EINVAL ; -if (usb_pipetype (urb->pipe) != pipetypes[usb_endpoint_type (&ep->desc)]) +if (usb_pipetype (pipe) != pipetypes[usb_endpoint_type (&ep->desc)])return -EINVAL ;return 0 ; } +EXPORT_SYMBOL_GPL (usb_pipe_type_check); + +/** +* usb_urb_ep_type_check - sanity check of endpoint in the given urb +* @urb: urb to be checked
drivers/usb/core/urb.c static const int pipetypes[4] = { · line 228
Quoted 10 lines
drivers/usb/core/urb.c +9
-0+* +* This performs a light-weight sanity check for the endpoint in the +* given urb. It returns 0 if the urb contains a valid endpoint, otherwise +* a negative error code. +*/ +int usb_urb_ep_type_check (const struct urb *urb) +{ +return usb_pipe_type_check (urb->dev, urb->pipe); +}EXPORT_SYMBOL_GPL (usb_urb_ep_type_check);
Since this routine is used in only one place in the entire kernel, you might as well inline the code there and get rid of the function entirely.
Quoted 14 lines
sound/usb/quirks.c +1
-1@@ -846,7 +846,7 @@ static int snd_usb_accessmusic_boot_quirk(struct usb_device *dev)static const u8 seq[] = {0x4e ,0x73 ,0x52 ,0x01 };void *buf; -if (snd_usb_pipe_sanity_check (dev,usb_sndintpipe (dev,0x05 ))) +if (usb_pipe_type_check (dev,usb_sndintpipe (dev,0x05 )))return -EINVAL ; buf =kmemdup (seq,ARRAY_SIZE (seq),GFP_KERNEL );if (!buf)
sound/usb/quirks.c static int snd_usb_nativeinstruments_boot_quirk(struct usb_device *dev) · line 879
Quoted 6 lines
sound/usb/quirks.c +1
-1@@ -875,7 +875,7 @@ static int snd_usb_nativeinstruments_boot_quirk(struct usb_device *dev) {int ret; -if (snd_usb_pipe_sanity_check (dev,usb_sndctrlpipe (dev,0 ))) +if (usb_pipe_type_check (dev,usb_sndctrlpipe (dev,0 )))return -EINVAL ;
In a few places here this check is completely unnecessary. All it does is verify that the device does have an endpoint 0 and the the type of the endpoint matches the type of the pipe. Well, every USB device always has an endpoint 0, and it is always a bidirectional control endpoint. Therefore a simple static check is all you need: There's no point calling usb_pipe_type_check() when the pipe is of the form usb_{snd|rcv}ctrlpipe(dev, 0).
In short, this check should be removed completely; it does nothing.
sound/usb/quirks.c static int snd_usb_axefx3_boot_quirk(struct usb_device *dev) · line 987
Quoted 8 lines
sound/usb/quirks.c +1
-1ret = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), 0xaf, USB_TYPE_VENDOR | USB_RECIP_DEVICE,@@ -984,7 +984,7 @@ static int snd_usb_axefx3_boot_quirk(struct usb_device *dev)dev_dbg (&dev->dev,"Waiting for Axe-Fx III to boot up...\n" ); -if (snd_usb_pipe_sanity_check (dev,usb_sndctrlpipe (dev,0 ))) +if (usb_pipe_type_check (dev,usb_sndctrlpipe (dev,0 )))
Same for this check.
Quoted 22 lines
sound/usb/quirks.c +2
-2return -EINVAL ;/* If the Axe-Fx III has not fully booted, it will timeout when trying * to enable the audio streaming interface. A more generous timeout is @@ -1018,7 +1018,7 @@ static int snd_usb_motu_microbookii_communicate(struct usb_device *dev, u8 *buf, {int err, actual_length; -if (snd_usb_pipe_sanity_check (dev,usb_sndintpipe (dev,0x01 ))) +if (usb_pipe_type_check (dev,usb_sndintpipe (dev,0x01 )))return -EINVAL ; err =usb_interrupt_msg (dev,usb_sndintpipe (dev,0x01 ), buf, *length, &actual_length,1000 );@@ -1030,7 +1030,7 @@ static int snd_usb_motu_microbookii_communicate(struct usb_device *dev, u8 *buf,memset (buf,0 , buf_size); -if (snd_usb_pipe_sanity_check (dev,usb_rcvintpipe (dev,0x82 ))) +if (usb_pipe_type_check (dev,usb_rcvintpipe (dev,0x82 )))return -EINVAL ; err =usb_interrupt_msg (dev,usb_rcvintpipe (dev,0x82 ), buf, buf_size, &actual_length,1000 );
sound/usb/quirks.c static int snd_usb_motu_m_series_boot_quirk(struct usb_device *dev) · line 1120
Quoted 5 lines
sound/usb/quirks.c +1
-1@@ -1117,7 +1117,7 @@ static int snd_usb_motu_m_series_boot_quirk(struct usb_device *dev) {int ret; -if (snd_usb_pipe_sanity_check (dev,usb_sndctrlpipe (dev,0 ))) +if (usb_pipe_type_check (dev,usb_sndctrlpipe (dev,0 )))
And this one.
sound/usb/quirks.c static int snd_usb_motu_m_series_boot_quirk(struct usb_device *dev) · line 1123
Quoted 3 lines
sound/usb/quirks.c +0
-0return -EINVAL ; ret = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), 1, USB_TYPE_VENDOR | USB_RECIP_DEVICE,
Alan Stern
Re: [PATCH 01/10] USB: move snd_usb_pipe_sanity_check into the USB core
Quoted 10 lines · Alan Stern
In a few places here this check is completely unnecessary. All it does is verify that the device does have an endpoint 0 and the the type of the endpoint matches the type of the pipe. Well, every USB device always has an endpoint 0, and it is always a bidirectional control endpoint. Therefore a simple static check is all you need: There's no point calling
usb_pipe_type_check()when the pipe is of the form usb_{snd|rcv}ctrlpipe(dev, 0).In short, this check should be removed completely; it does nothing.
Fair enough, but I think those removals should be in another patch.
thanks,
Takashi
Greg Kroah-Hartman
maintainerRe: [PATCH 01/10] USB: move snd_usb_pipe_sanity_check into the USB core
In reply to Alan SternQuoted 34 lines · Alan Stern
Quoted 33 lines · Greg Kroah-Hartman
snd_usb_pipe_sanity_check()is a great function, so let's move it into the USB core so that other parts of the kernel, including the USB core, can call it.Name it
usb_pipe_type_check()to match the existingusb_urb_ep_type_check()call, which now uses this function.Cc Jaroslav Kysela <[email protected]>Cc Takashi Iwai <[email protected]>Cc "Gustavo A. R. Silva" <[email protected]>Cc Eli Billauer <[email protected]>Cc Emiliano Ingrassia <[email protected]>Cc Alan Stern <[email protected]>Cc Alexander Tsoy <[email protected]>Cc "Geoffrey D. Bennett" <[email protected]>Cc Jussi Laako <[email protected]>Cc Nick Kossifidis <[email protected]>Cc Dmitry Panchenko <[email protected]>Cc Chris Wulff <[email protected]>Cc Jesus Ramos <[email protected]>Signed-off-by Greg Kroah-Hartman <[email protected]>---
drivers/usb/core/urb.c +0
-0@@ -192,24 +192,39 @@ static const int pipetypes[4] = { };
Quoted 13 lines
drivers/usb/core/urb.c static const int pipetypes[4] = { · line 200
Quoted 11 lines
drivers/usb/core/urb.c +4
-4/** -* usb_urb_ep_type_check - sanity check of endpoint in the given urb -* @urb: urb to be checked +* usb_pipe_type_check - sanity check of a specific pipe for a usb device +* @dev: struct usb_device to be checked +* @pipe: pipe to check * * This performs a light-weight sanity check for the endpoint in the -* given urb. It returns 0 if the urb contains a valid endpoint, otherwise -* a negative error code. +* given usb device. It returns 0 if the pipe is a valid for the specific usb -----------------------------------------------------^ Typo.
Oops, will fix, thanks.
Quoted 28 lines
Quoted 28 lines
drivers/usb/core/urb.c +15
-3+* device, otherwise a negative error code. */ -int usb_urb_ep_type_check (const struct urb *urb) +int usb_pipe_type_check (struct usb_device *dev,unsigned int pipe) {const struct usb_host_endpoint *ep; - ep =usb_pipe_endpoint (urb->dev, urb->pipe); + ep =usb_pipe_endpoint (dev, pipe);if (!ep)return -EINVAL ; -if (usb_pipetype (urb->pipe) != pipetypes[usb_endpoint_type (&ep->desc)]) +if (usb_pipetype (pipe) != pipetypes[usb_endpoint_type (&ep->desc)])return -EINVAL ;return 0 ; } +EXPORT_SYMBOL_GPL (usb_pipe_type_check); + +/** +* usb_urb_ep_type_check - sanity check of endpoint in the given urb +* @urb: urb to be checked +* +* This performs a light-weight sanity check for the endpoint in the +* given urb. It returns 0 if the urb contains a valid endpoint, otherwise +* a negative error code. +*/ +int usb_urb_ep_type_check (const struct urb *urb)
Quoted 8 lines
drivers/usb/core/urb.c static const int pipetypes[4] = { · line 228
Quoted 4 lines
drivers/usb/core/urb.c +3
-0+{ +return usb_pipe_type_check (urb->dev, urb->pipe); +}EXPORT_SYMBOL_GPL (usb_urb_ep_type_check);Since this routine is used in only one place in the entire kernel, you might as well inline the code there and get rid of the function entirely.
Good idea, will do.
Quoted 17 lines
Quoted 17 lines
sound/usb/quirks.c +1
-1@@ -846,7 +846,7 @@ static int snd_usb_accessmusic_boot_quirk(struct usb_device *dev)static const u8 seq[] = {0x4e ,0x73 ,0x52 ,0x01 };void *buf; -if (snd_usb_pipe_sanity_check (dev,usb_sndintpipe (dev,0x05 ))) +if (usb_pipe_type_check (dev,usb_sndintpipe (dev,0x05 )))return -EINVAL ; buf =kmemdup (seq,ARRAY_SIZE (seq),GFP_KERNEL );if (!buf)@@ -875,7 +875,7 @@ static int snd_usb_nativeinstruments_boot_quirk(struct usb_device *dev) {int ret;
Quoted 9 lines
sound/usb/quirks.c static int snd_usb_nativeinstruments_boot_quirk(struct usb_device *dev) · line 879
Quoted 3 lines
sound/usb/quirks.c +1
-1-if (snd_usb_pipe_sanity_check (dev,usb_sndctrlpipe (dev,0 ))) +if (usb_pipe_type_check (dev,usb_sndctrlpipe (dev,0 )))return -EINVAL ;In a few places here this check is completely unnecessary. All it does is verify that the device does have an endpoint 0 and the the type of the endpoint matches the type of the pipe. Well, every USB device always has an endpoint 0, and it is always a bidirectional control endpoint.
I think this was probably added to handle syzbot issues. As long as the USB core does ensure that a USB device has endpoint 0, I agree, these can be removed. I'll go check that and add a follow-on patch to the series to do this, thanks.
thanks,
greg k-h
Greg Kroah-Hartman
maintainerRe: [PATCH 01/10] USB: move snd_usb_pipe_sanity_check into the USB core
Quoted 89 lines · Greg Kroah-Hartman
Quoted 34 lines · Alan Stern
Quoted 33 lines · Greg Kroah-Hartman
snd_usb_pipe_sanity_check()is a great function, so let's move it into the USB core so that other parts of the kernel, including the USB core, can call it.Name it
usb_pipe_type_check()to match the existingusb_urb_ep_type_check()call, which now uses this function.Cc Jaroslav Kysela <[email protected]>Cc Takashi Iwai <[email protected]>Cc "Gustavo A. R. Silva" <[email protected]>Cc Eli Billauer <[email protected]>Cc Emiliano Ingrassia <[email protected]>Cc Alan Stern <[email protected]>Cc Alexander Tsoy <[email protected]>Cc "Geoffrey D. Bennett" <[email protected]>Cc Jussi Laako <[email protected]>Cc Nick Kossifidis <[email protected]>Cc Dmitry Panchenko <[email protected]>Cc Chris Wulff <[email protected]>Cc Jesus Ramos <[email protected]>Signed-off-by Greg Kroah-Hartman <[email protected]>---
drivers/usb/core/urb.c +0
-0@@ -192,24 +192,39 @@ static const int pipetypes[4] = { };Quoted 13 lines
drivers/usb/core/urb.c static const int pipetypes[4] = { · line 200
Quoted 11 lines
drivers/usb/core/urb.c +4
-4/** -* usb_urb_ep_type_check - sanity check of endpoint in the given urb -* @urb: urb to be checked +* usb_pipe_type_check - sanity check of a specific pipe for a usb device +* @dev: struct usb_device to be checked +* @pipe: pipe to check * * This performs a light-weight sanity check for the endpoint in the -* given urb. It returns 0 if the urb contains a valid endpoint, otherwise -* a negative error code. +* given usb device. It returns 0 if the pipe is a valid for the specific usb -----------------------------------------------------^ Typo.
Oops, will fix, thanks.
Quoted 28 lines
Quoted 28 lines
drivers/usb/core/urb.c +15
-3+* device, otherwise a negative error code. */ -int usb_urb_ep_type_check (const struct urb *urb) +int usb_pipe_type_check (struct usb_device *dev,unsigned int pipe) {const struct usb_host_endpoint *ep; - ep =usb_pipe_endpoint (urb->dev, urb->pipe); + ep =usb_pipe_endpoint (dev, pipe);if (!ep)return -EINVAL ; -if (usb_pipetype (urb->pipe) != pipetypes[usb_endpoint_type (&ep->desc)]) +if (usb_pipetype (pipe) != pipetypes[usb_endpoint_type (&ep->desc)])return -EINVAL ;return 0 ; } +EXPORT_SYMBOL_GPL (usb_pipe_type_check); + +/** +* usb_urb_ep_type_check - sanity check of endpoint in the given urb +* @urb: urb to be checked +* +* This performs a light-weight sanity check for the endpoint in the +* given urb. It returns 0 if the urb contains a valid endpoint, otherwise +* a negative error code. +*/ +int usb_urb_ep_type_check (const struct urb *urb)Quoted 8 lines
drivers/usb/core/urb.c static const int pipetypes[4] = { · line 228
Quoted 4 lines
drivers/usb/core/urb.c +3
-0+{ +return usb_pipe_type_check (urb->dev, urb->pipe); +}EXPORT_SYMBOL_GPL (usb_urb_ep_type_check);Since this routine is used in only one place in the entire kernel, you might as well inline the code there and get rid of the function entirely.
Quoted 1 line
Good idea, will do.
No, wait, the USB sound drivers call it a lot, so it needs to stick around for now until we clean that up.
thanks,
greg k-h
Re: [PATCH 01/10] USB: move snd_usb_pipe_sanity_check into the USB core
Quoted 11 lines · Greg Kroah-Hartman
Quoted 7 lines · Greg Kroah-Hartman
Quoted 3 lines · Alan Stern
Since this routine is used in only one place in the entire kernel, you might as well inline the code there and get rid of the function entirely.
Good idea, will do.
No, wait, the USB sound drivers call it a lot, so it needs to stick around for now until we clean that up.
Argh. I must have run "git grep" from within drivers/usb/core. My mistake.
Alan Stern
Greg Kroah-Hartman
maintainerRe: [PATCH 01/10] USB: move snd_usb_pipe_sanity_check into the USB core
In reply to Takashi IwaiQuoted 28 lines · Takashi Iwai
Quoted 17 lines · Greg Kroah-Hartman
snd_usb_pipe_sanity_check()is a great function, so let's move it into the USB core so that other parts of the kernel, including the USB core, can call it.Name it
usb_pipe_type_check()to match the existingusb_urb_ep_type_check()call, which now uses this function.Cc Jaroslav Kysela <[email protected]>Cc Takashi Iwai <[email protected]>Cc "Gustavo A. R. Silva" <[email protected]>Cc Eli Billauer <[email protected]>Cc Emiliano Ingrassia <[email protected]>Cc Alan Stern <[email protected]>Cc Alexander Tsoy <[email protected]>Cc "Geoffrey D. Bennett" <[email protected]>Cc Jussi Laako <[email protected]>Quoted 8 lines
Cc Nick Kossifidis <[email protected]>Cc Dmitry Panchenko <[email protected]>Cc Chris Wulff <[email protected]>Cc Jesus Ramos <[email protected]>Signed-off-by Greg Kroah-Hartman <[email protected]>
Quoted 1 line
Reviewed-by Takashi Iwai <[email protected]>
Thanks for the reviews of all of these.
greg k-h